Add callback to retrieve the current set norm.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Issue a V4L2_EVENT_SOURCE_CHANGE notification when the TVP5150 locks
onto a signal and when it loses the lock.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: partly mainline part port]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To avoid short frames on stream start, keep output pins at high impedance
while we are not properly locked onto the input signal.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds an optional interrupt handler to handle the sync
lock interrupt and sync lock status.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[m.felsch@pengutronix.de: move added .g_std callback to separate patch]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To allow optional interrupt support, we want to configure the pin settings
dynamically. Move those register accesses out of the static initialization
tables.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: drop init_default register remove]
[m.felsch@pengutronix.de: fix regmap access during reset()]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To trigger standard autodetection only the reset part of the routine
is necessary during probe(). Split this out to make it callable on its own.
[m.felsch@pengutronix.de: adapt commit message]
[m.felsch@pengutronix.de: add tvp5150_enable() to tvp5150_s_stream()]
[m.chehab@samsung.com: fix a compilation breakage]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure to not overwrite decoder->norm when setting the standard
in hardware, but only when instructed by V4L2 API calls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If cropping isn't set explicitly by userspace, reset it to the maximum
possible rectangle in subdevice open if a standard change is detected.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: move code from internal_ops.open() to pad_ops.init_cfg()]
[m.felsch@pengutronix.de: make use of tvp5150_set_default() helper]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The patch adds three macros to bundle the mbus_framefmt default
values and a helper function to set the the default crop and
mbus_framefmt values.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 9a4c7e68f7e0 ("media: tvp5150: convert register
access to regmap")' the driver supports regmap. Now we can drop
the handmade bit update sequence and move to the regmap provided
helpers.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Regmap provides built in debugging, caching and provides dedicated
accessors for bit manipulations in registers, which make the following
changes a lot simpler.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function only consists of a single switch case block without a
default case. Unsupported control requests are indicated by the -EINVAL
return code trough the last return statement at the end of the function. So
exiting just the switch case block returns the -EINVAL error code but the
hue control is supported and a zero should be returned instead.
Replace the break by a 'return 0' to fix this behaviour.
Fixes: d183e4efca ("[media] v4l: tvp5150: Add missing break in set
control handler")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver ignored the width alignment which exists due to the UYVY
colorspace format. Fix the width alignment and make use of the the
provided v4l2 helper function to set the width, height and all
alignments in one.
Fixes: 963ddc63e2 ("[media] media: tvp5150: Add cropping support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Consumer devices are provided with a wide different range of types
supported by the same driver, allowing different configutations.
In order to make easier to setup media controller links, "taint"
pads with the signal type it carries.
While here, get rid of DEMOD_PAD_VBI_OUT, as the signal it carries
is actually the same as the normal video output.
The difference happens at the video/VBI interface:
- for VBI, only the hidden lines are streamed;
- for video, the stream is usually cropped to hide the
vbi lines.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The signal there is the same as the video output (well,
except for sliced VBI, but let's simplify the model and ignore
it, at least for now - as it is routed together with raw
VBI).
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
Cc: Benoit Parrot <bparrot@ti.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Hyun Kwon <hyun.kwon@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As original license mentioned, it is GPL-2.0+ in SPDX.
Then, MODULE_LICENSE() should be "GPL" instead of "GPL v2".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix error handling of v4l2_ctrl creation by inspecting the ctrl.error flag
instead of testing for each returned value correctness.
As reported by Dan Carpenter returning PTR_ERR() on the v4l2_ctrl_new_std()
return value is also wrong, as that function return NULL on error.
While at there re-order the cleanup path to respect the operation inverse
order.
Fixes: aab7ed1c "media: i2c: Add driver for Aptina MT9V111"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The strcpy() function is being deprecated upstream. Replace
it by the safer strscpy().
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix error handling of v4l2_ctrl creation by inspecting the ctrl.error flag
instead of testing for each returned value correctness.
As reported by Dan Carpenter returning PTR_ERR() on the v4l2_ctrl_new_std()
return value is also wrong, as that function return NULL on error.
While at there re-order the cleanup path to respect the operation inverse
order.
Fixes: aab7ed1c "media: i2c: Add driver for Aptina MT9V111"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The pixelclock detection of the adv7842 is precise enough to detect
if the framerate is 60 Hz or 59.94 Hz (aka "reduced fps").
Implement this detection.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
fixes: 6949d86477 ("media: ov5640: do not change mode if format or frame interval is unchanged").
Symptom was fuzzy image because of JPEG default format
not being changed according to new format selected, fix this.
Init sequence initialises format to YUV422 UYVY but
sensor->fmt initial value was set to JPEG, fix this.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If ov772x_power_on() is unable to get GPIO rstb,
the clock is left undisabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
pm_runtime_get_if_in_use() returns -EINVAL if runtime PM is disabled. This
should not be considered an error. Generally the driver has enabled
runtime PM already so getting this error due to runtime PM being disabled
will not happen.
Instead of checking for lesser or equal to zero, check for zero only.
Address this for drivers where this pattern exists.
This patch has been produced using the following command:
$ git grep -l pm_runtime_get_if_in_use -- drivers/media/i2c/ | \
xargs perl -i -pe 's/(pm_runtime_get_if_in_use\(.*\)) \<\= 0/!$1/'
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Replace the calls to pm_runtime_get_noresume() and pm_runtime_put() with
pm_runtime_idle() in the driver's probe function. This will have the same
effect with fewer calls. pm_runtime_disable() in remove is sufficient as
the device is already in RPM_SUSPENDED state.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_subdev_get_try_format() function is only defined if the
VIDEO_V4L2_SUBDEV_API Kconfig option is enabled. Builds configured
without that symbol fails with:
drivers/media/i2c/mt9v111.c:801:10: error: implicit declaration of function
'v4l2_subdev_get_try_format';
Fix this by protecting the function call by testing for the right symbol.
media: mt9v111: fix random build errors
Fix the internal check for it to do the right thing if the
subdev API is not built.
Fixes: aab7ed1c ("media: i2c: Add driver for Aptina MT9V111")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This fixes the "'idx' may be used uninitialized in this function"
warning:
drivers/media/i2c/mt9v111.c: In function 'mt9v111_set_format':
drivers/media/i2c/mt9v111.c:887:15: warning: 'idx' may be used uninitialized in this function [-Wmaybe-uninitialized]
unsigned int idx;
^~~
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently this driver does not support cropping. The supported modes
are the following, all capturing the entire area:
- 3840x2160, 1:1 binning (native sensor resolution)
- 1920x1080, 2:1 binning
- 1280x720, 3:1 binning
The VIDIOC_SUBDEV_S_FMT ioctl chooses among these 3 configurations the
one that matches the requested format.
Add cropping support via VIDIOC_SUBDEV_S_SELECTION: with target
V4L2_SEL_TGT_CROP to choose the captured area, with
V4L2_SEL_TGT_COMPOSE to choose the output resolution.
To maintain backward compatibility we also allow setting the compose
format via VIDIOC_SUBDEV_S_FMT. To obtain this, compose rect and
output format are computed in the common helper function
__imx274_change_compose(), which sets both to the same width/height
values.
Cropping also calls __imx274_change_compose() whenever cropping rect
size changes in order to reset the compose rect (and output format
size) for 1:1 binning.
Also rename enum imx274_mode to imx274_binning (and its values from
IMX274_MODE_BINNING_* to IMX274_BINNING_*). Without cropping, the two
naming are equivalent. With cropping, the resolution could be
different, e.g. using 2:1 binning mode to crop 1200x960 and output a
600x480 format. Using binning in the names avoids any
misunderstanding. For the same reason, replace the 'size' field in
struct imx274_frmfmt with 'bin_ratio'.
[Sakari Ailus: Remove leftover condition in imx274_apply_trimming]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently 2-bytes and 3-bytes registers are set by very similar
functions doing the needed shift & mask manipulation, followed by very
similar for loops setting one byte at a time over I2C.
Replace all of this code by a unique helper function that calls
regmap_bulk_write(), which has two advantages:
- sets all the bytes in a unique I2C transaction
- removes lots of now unused code.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds V4L2 sub-device driver for OV2680 image sensor.
The OV2680 is a 1/5" CMOS color sensor from Omnivision.
Supports output format: 10-bit Raw RGB.
The OV2680 has a single lane MIPI interface.
The driver exposes following V4L2 controls:
- auto/manual exposure,
- exposure,
- auto/manual gain,
- gain,
- horizontal/vertical flip,
- test pattern menu.
Supported resolution are only: QUXGA, 720P, UXGA.
[Sakari Ailus: Drop "-level" from Kconfig help text]
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add V4L2 sensor driver for Aptina MT9V111 CMOS image sensor.
The MT9V111 is a 1/4-Inch CMOS image sensor based on MT9V011 with an
integrated Image Flow Processor.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The dw9807 contains a voice coil lens driver as well as an EEPROM. This
driver is just for the VCM. Reflect this in the driver's name --- this is
already the case for the compatible string, for instance.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vs6624_probe() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
adv7842_ddr_ram_test() is never called in atomic context.
It only calls from:
adv7842_ddr_ram_test() <- adv7842_command_ram_test() <- adv7842_ioctl()
adv7842_ddr_ram_test() calls mdelay() to busily wait,
which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
PTR_ERR was making any pointer passed an error pointer, and should be
replaced with PTR_ERR_OR_ZERO which checks if is an actual error condition.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV7180 and ADV7182 transmit whole fields, bottom field followed
by top (or vice-versa, depending on detected video standard). So
for chips that do not have support for explicitly setting the field
mode via I2P, set the field mode to V4L2_FIELD_ALTERNATE.
I2P converts fields into frames using an edge adaptive algorithm. The
frame rate is the same as the 'field rate': e.g. X fields per second
are now X frames per second.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
AMG88xx has an on-board thermistor which is used for more accurate
processing of its temperature readings from the 8x8 thermopile array
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Several drivers in media/i2c do not set the entity function.
Correct this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The entity function was ORed with the flags field instead of
assigned to the function field. Correct this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These two drivers both have function MEDIA_ENT_F_DV_ENCODER.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The use of 'DTV' is very confusing since it normally refers to Digital
TV e.g. DVB etc.
Instead use 'DV' (Digital Video), which nicely corresponds to the
DV Timings API used to configure such receivers and transmitters.
We keep an alias to avoid breaking userspace applications.
Since this alias is only available if __KERNEL__ is *not* defined
(i.e. it is only available for userspace, not kernelspace), any
drivers that use it also have to be converted to the new define.
These drivers are adv7604, adv7842 and tda1997x.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A lot of sensor drivers are labelled as "sensor-level" drivers. That's
odd and somewhat confusing as the term isn't used elsewhere: these are
just sensor drivers. Call them such.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The just parsed endpoint fwnode has to be put after use.
Currently this is done only in error handling path. Fix that by
putting node unconditionally after use.
Fixes: 01b8444828 ("media: v4l2: i2c: ov7670: Implement OF mbus configuration")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The external clock frequency was set to 23.88MHz by mistake
because of a platform which cannot get closer to 24MHz.
The supported by the driver external clock is 24MHz so
set it correctly and also fix the values of the pixel
clock and link clock.
However allow 1% tolerance to the external clock as this
difference is small enough to be insignificant.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Save load of mode registers array when V4L2 client sets a format or a
frame interval which selects the same mode than the current one.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The smiapp driver is licensed under GNU GPL v2 only, as stated by the
header. Reflect this in the MODULE_LICENSE macro.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This commit describes a device instance private data of the driver
(struct cx25840_state) in a kernel-doc style comment.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
imx274_write_table() is a mere wrapper (and the only user) to
imx274_regmap_util_write_table_8(). Remove this useless indirection by
merging the two functions into one.
Also get rid of the wait_ms_addr and end_addr parameters since it does
not make any sense to give them any values other than
IMX274_TABLE_WAIT_MS and IMX274_TABLE_END.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
IMX274_DEFAULT_MODE is defined but not used. Start using it, so the
default can be more easily changed without digging into the code.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After restructuring struct imx274_frmfmt, the mode_index field is
still in use only for two dev_dbg() calls in imx274_s_stream(). Let's
remove it and avoid duplicated information.
Replacing the first usage requires some rather annoying but trivial
pointer math. The other one can be removed entirely since it would
print the same value anyway.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Data about the implemented readout modes is partially stored in
imx274_formats[], the rest is scattered in several arrays. The latter
are then accessed using the mode index, e.g.:
min_frame_len[priv->mode_index]
Consolidate all these data in imx274_formats[], and store a pointer to
the selected mode (i.e. imx274_formats[priv->mode_index]) in the main
device struct. This way code to use these data becomes more readable,
e.g.:
priv->mode->min_frame_len
This removes lots of scaffolding code and keeps data about each mode
in a unique place.
Also remove a parameter to imx274_mode_regs() that is now unused.
While this adds the mode pointer to the device struct, it does not
remove the mode_index from it because mode_index is still used in two
dev_dbg() calls. This will be handled in a follow-up commit.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The current probe function calls v4l2_ctrl_handler_setup() before
initializing the format info. This triggers call paths such as:
imx274_probe -> v4l2_ctrl_handler_setup -> imx274_s_ctrl ->
imx274_set_exposure, where priv->mode_index is accessed before being
assigned.
This is wrong but does not trigger a visible bug because priv is
zero-initialized and 0 is the default value for priv->mode_index. But
this would become a crash in follow-up commits when mode_index is
replaced by a pointer that must always be valid.
Fix the bug before it shows up by initializing struct members early.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a v4l2 sub-device driver for the ak7375 lens voice coil.
This is a voice coil module using the i2c bus to control the
focus position.
ak7375 can write multiple bytes of data at a time. If more
data is received instead of the stop condition after receiving
one byte of data, the address inside the chip is automatically
incremented and the data is written into the next address.
The ak7375 can control the position with 12 bits value and
consists of two 8 bit registers show as below:
register 0x00(AK7375_REG_POSITION):
+---+---+---+---+---+---+---+---+
|D11|D10|D09|D08|D07|D06|D05|D04|
+---+---+---+---+---+---+---+---+
register 0x01:
+---+---+---+---+---+---+---+---+
|D03|D02|D01|D00|---|---|---|---|
+---+---+---+---+---+---+---+---+
This driver support :
- set ak7375 to standby mode once suspend and
turn it back to active if resume
- set the position via V4L2_CID_FOCUS_ABSOLUTE ctrl
[Sakari Ailus: Rename val as ret in probe, drop redundant error message]
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Driver must reject frame interval enumeration of unsupported resolution.
This was detected by v4l2-compliance format ioctl test:
v4l2-compliance Format ioctls:
info: found 2 frameintervals for pixel format 4745504a and size 176x144
fail: v4l2-test-formats.cpp(123):
found frame intervals for invalid size 177x144
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
According to ov5640 datasheet xvclk is allowed to be between 6 and 54 MHz.
I run a successful test with 27 MHz.
Signed-off-by: Philipp Puschmann <pp@emlix.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The banding filter ON/OFF is controlled via bit 5 of COM8 register. It
is attempted to be enabled in ov772x_set_params() by the following line.
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, 1);
But this unexpectedly results disabling the banding filter, because the
mask and set bits are exclusive.
On the other hand, ov772x_s_ctrl() correctly sets the bit by:
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, BNDF_ON_OFF);
The same fix was already applied to non-soc_camera version of ov772x
driver in the commit commit a024ee14cd ("media: ov772x: correct setting
of banding filter")
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
DW9807 is a 10 bit DAC from Dongwoon, designed for linear
control of voice coil motor.
This driver creates a V4L2 subdevice and
provides control to set the desired focus.
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so that the
subdevice device node is created.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver is going to offer a V4L2 sub-device interface, so
changing the output data format and the frame interval on this sub-device
can be made anytime. However, these requests are preferred to fail while
the video stream on the device is active.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The set_fmt() in subdev pad ops, the s_ctrl() for subdev control handler,
and the s_frame_interval() in subdev video ops could be called when the
device is under power saving mode. These callbacks for ov772x driver
cause updating H/W registers that will fail under power saving mode.
This avoids it by not apply any changes to H/W if the device is not powered
up. Instead the changes will be restored right after power-up.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver provides three V4L2 controls and the current value of
each control is saved as a variable in the private data structure.
We don't need to keep track of the current value by ourself, if we use
v4l2_ctrl returned from v4l2_ctrl_new_std() instead.
This is a preparatory change to avoid accessing registers under power
saving mode. This simplifies s_ctrl() by making it just return without
saving the current control value in private area when it is called under
power saving mode.
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This splits the s_frame_interval() in subdev video ops into selecting the
frame interval and setting up the registers.
This is a preparatory change to avoid accessing registers under power
saving mode.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Depending on the v4l2 driver, calling s_power() could be nested. So the
actual transitions between power saving mode and normal operation mode
should only happen at the first power on and the last power off.
This adds an s_power() nesting counter and updates the power state if the
counter is modified from 0 to != 0 or from != 0 to 0.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver currently only supports legacy platform data probe.
This change enables device tree probing.
Note that the platform data probe can select auto or manual edge control
mode, but the device tree probling can only select auto edge control mode
for now.
[Sakari Ailus: Remove direct OF dependencies from device ID table]
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the ov772x driver obtains a clock with a specific consumer ID.
As there's a single clock for this driver, we could omit clock-names
property in device tree by passing NULL as a consumer ID to clk_get().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver uses "rstb-gpios" and "pwdn-gpios" for reset and
powerdown pins. However, using generic names for these gpios is
preferred. ("reset-gpios" and "powerdown-gpios" respectively)
There is only one mainline user for these gpios, so rename to generic
names.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Create a source pad and set the media controller type to the sensor.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver only works when the i2c controller have
I2C_FUNC_PROTOCOL_MANGLING. However, many i2c controller drivers don't
support it.
The reason that the ov772x requires I2C_FUNC_PROTOCOL_MANGLING is that
it doesn't support repeated starts.
This changes the reading ov772x register method so that it doesn't
require I2C_FUNC_PROTOCOL_MANGLING by calling two separated i2c messages.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support of module being physically mounted upside down.
In this case, mirror and flip are enabled to fix captured images
orientation.
[Sakari Ailus: Use dev_fwnode() instead of accessing device's of_node]
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add HFLIP/VFLIP controls support by setting registers REG21/REG20.
Useless values in hardcoded mode sequences are removed and
remaining binning values are now set after mode sequence being set.
Note that due to BSI (Back Side Illuminated) technology, image capture
is physically mirrored, mirror logic is so inversed in REG21 register
to cancel this effect.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the "rotation" property to tell that the sensor is mounted upside
down. This reverses the behaviour of the VFLIP and HFLIP controls as well
as the pixel order.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts commit 0866df8dff.
The v4l uAPI documentation [0] makes clear that in the case of interlaced
video (i.e: field is V4L2_FIELD_ALTERNATE) the height refers to the number
of lines in the field and not the number of lines in the full frame (which
is twice the field height for interlaced formats).
So the original height calculation was correct, and it shouldn't had been
changed by the mentioned commit.
[0]:https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/subdev-formats.html
Fixes: 0866df8dff ("[media] tvp5150: fix pad format frame height")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Cc: <stable@vger.kernel.org> # for v4.12 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove soc_camera framework dependencies from rj54n1 sensor driver.
- Handle clock
- Handle GPIOs (named 'powerup' and 'enable')
- Register the async subdevice
- Remove g/s_mbus_config as they're deprecated.
- Adjust build system
- List the driver as maintained for 'Odd Fixes' as I don't have HW to test.
This commits does not remove the original soc_camera based driver.
Compiled tested only.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Copy the soc_camera based driver in v4l2 sensor driver directory.
This commit just copies the original file without modifying it.
No modification to KConfig and Makefile as soc_camera framework
dependencies need to be removed first in next commit.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for LM3559, as found in Motorola Droid 4 phone, for
example. SW interface seems to be identical.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the of_node_put() is unconditional here there is no need to have it
twice.
Signed-off-by: Nicholas Mc Guire <hofrat@opentech.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
of_graph_get_next_endpoint() returns device_node with refcnt increased,
but these is no of_node_put() for it.
The patch adds one on error and normal paths.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver only supports streaming images flipped horizontally and
vertically. In order to ensure that all current users will be fine if or
when support for upright streaming is added, require the presence of the
"rotation" control now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: "Lai, Jim" <jim.lai@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----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=r/WP
-----END PGP SIGNATURE-----
Merge tag 'media/v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove of atomisp driver from staging, as nobody would have time to
dedicate huge efforts to fix all the problems there. Also, we have a
feeling that the driver may not even run the way it is.
- move Zoran driver to staging, in order to be either fixed to use VB2
and the proper media kAPIs or to be removed
- remove videobuf-dvb driver, with is unused for a while
- some V4L2 documentation fixes/improvements
- new sensor drivers: imx258 and ov7251
- a new driver was added to allow using I2C transparent drivers
- several improvements at the ddbridge driver
- several improvements at the ISDB pt1 driver, making it more coherent
with the DVB framework
- added a new platform driver for MIPI CSI-2 RX: cadence
- now, all media drivers can be compiled on x86 with COMPILE_TEST
- almost all media drivers now build on non-x86 architectures with
COMPILE_TEST
- lots of other random stuff: cleanups, support for new board models,
bug fixes, etc
* tag 'media/v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
media: omap2: fix compile-testing with FB_OMAP2=m
media: media/radio/Kconfig: add back RADIO_ISA
media: v4l2-ioctl.c: fix missing unlock in __video_do_ioctl()
media: pxa_camera: ignore -ENOIOCTLCMD from v4l2_subdev_call for s_power
media: arch: sh: migor: Fix TW9910 PDN gpio
media: staging: tegra-vde: Reset VDE regardless of memory client resetting failure
media: marvel-ccic: mmp: select VIDEOBUF2_VMALLOC/DMA_CONTIG
media: marvel-ccic: allow ccic and mmp drivers to coexist
media: uvcvideo: Prevent setting unavailable flags
media: ddbridge: conditionally enable fast TS for stv0910-equipped bridges
media: dvb-frontends/stv0910: make TS speed configurable
media: ddbridge/mci: add identifiers to function definition arguments
media: ddbridge/mci: protect against out-of-bounds array access in stop()
media: rc: ensure input/lirc device can be opened after register
media: rc: nuvoton: Keep device enabled during reg init
media: rc: nuvoton: Keep track of users on CIR enable/disable
media: rc: nuvoton: Tweak the interrupt enabling dance
media: uvcvideo: Support realtek's UVC 1.5 device
media: uvcvideo: Fix driver reference counting
media: gspca_zc3xx: Enable short exposure times for OV7648
...
We've got many code additions at this cycle as a result of quite a few
new drivers. Below are highlights:
Core stuff:
- Fix the long-standing issue with the device registration order;
the control device is now registered at last
- PCM locking code cleanups for RT kernels
- Fixes for possible races in ALSA timer resolution accesses
- TLV offset definitions in uapi
ASoC:
- Many fixes for the topology stuff, including fixes for v4 ABI
compatibility
- Lots of cleanups / quirks for Intel platforms based on Realtek
CODECs
- Continued componentization works, removing legacy CODEC stuff
- Conversion of OMAP DMA to the new, more standard SDMA-PCM driver
- Fixes and updates to Cirrus Logic SoC drivers
- New Qualcomm DSP support
- New drivers for Analog SSM2305, Atmel I2S controllers, Mediatek
MT6351, MT6797 and MT7622, Qualcomm DSPs, Realtek RT1305, RT1306 and
RT5668 and TI TSCS454
HD-audio:
- Finally better support for some CA0132 boards, allowing Windows
firmware
- HP Spectre x360 support along with a bulk of COEF stuff
- Blacklisting power save default some known boards reported on Fedora
USB-audio:
- Continued improvements on UAC3 support; now BADD is supported
- Fixes / improvements for Dell WD15 dock
- Allow DMA coherent pages for PCM buffers for ARCH, MIPS & co
Others:
- New Xen sound frontend driver support
- Cache implementation and other improvements for FireWire DICE
- Conversions to octal permissions in allover places
-----BEGIN PGP SIGNATURE-----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=37hC
-----END PGP SIGNATURE-----
Merge tag 'sound-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"We've got many code additions at this cycle as a result of quite a few
new drivers. Below are highlights:
Core stuff:
- Fix the long-standing issue with the device registration order; the
control device is now registered at last
- PCM locking code cleanups for RT kernels
- Fixes for possible races in ALSA timer resolution accesses
- TLV offset definitions in uapi
ASoC:
- Many fixes for the topology stuff, including fixes for v4 ABI
compatibility
- Lots of cleanups / quirks for Intel platforms based on Realtek
CODECs
- Continued componentization works, removing legacy CODEC stuff
- Conversion of OMAP DMA to the new, more standard SDMA-PCM driver
- Fixes and updates to Cirrus Logic SoC drivers
- New Qualcomm DSP support
- New drivers for Analog SSM2305, Atmel I2S controllers, Mediatek
MT6351, MT6797 and MT7622, Qualcomm DSPs, Realtek RT1305, RT1306
and RT5668 and TI TSCS454
HD-audio:
- Finally better support for some CA0132 boards, allowing Windows
firmware
- HP Spectre x360 support along with a bulk of COEF stuff
- Blacklisting power save default some known boards reported on
Fedora
USB-audio:
- Continued improvements on UAC3 support; now BADD is supported
- Fixes / improvements for Dell WD15 dock
- Allow DMA coherent pages for PCM buffers for ARCH, MIPS & co
Others:
- New Xen sound frontend driver support
- Cache implementation and other improvements for FireWire DICE
- Conversions to octal permissions in allover places"
* tag 'sound-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (386 commits)
ASoC: dapm: delete dapm_kcontrol_data paths list before freeing it
ALSA: usb-audio: remove redundant check on err
ASoC: topology: Move skl-tplg-interface.h to uapi
ASoC: topology: Move v4 manifest header data structures to uapi
ASoC: topology: Improve backwards compatibility with v4 topology files
ALSA: pci/hda: Remove unused, broken, header file
ASoC: TSCS454: Add Support
ASoC: Intel: kbl: Move codec sysclk config to codec_init function
ASoC: simple-card: set cpu dai clk in hw_params
ALSA: hda - Handle kzalloc() failure in snd_hda_attach_pcm_stream()
ALSA: oxygen: use match_string() helper
ASoC: dapm: use match_string() helper
ASoC: max98095: use match_string() helper
ASoC: max98088: use match_string() helper
ASoC: Intel: bytcr_rt5651: Set card long_name based on quirks
ASoC: mt6797-mt6351: add hostless phone call path
ASoC: mt6797: add Hostless DAI
ASoC: mt6797: add PCM interface
ASoC: mediatek: export mtk-afe symbols as needed
ASoC: codecs: PCM1789: include gpio/consumer.h
...
If a CEC message was received and the RX interrupt was set, but
not yet processed, and a new transmit was issues, then the
transmit code would inadvertently clear the RX interrupt and
after that no new messages would ever be received.
Instead it should only clear TX interrupts since register 0x97
is a clear-on-write register.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The banding filter ON/OFF is controlled via bit 5 of COM8 register. It
is attempted to be enabled in ov772x_set_params() by the following line.
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, 1);
But this unexpectedly results disabling the banding filter, because the
mask and set bits are exclusive.
On the other hand, ov772x_s_ctrl() correctly sets the bit by:
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, BNDF_ON_OFF);
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/media/i2c/imx258.c: In function 'imx258_init_controls':
drivers/media/i2c/imx258.c:1117:6: warning: variable 'exposure_max' set but not used [-Wunused-but-set-variable]
s64 exposure_max;
^~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a V4L2 sub-device driver for the Sony IMX258 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
Signed-off-by: Jason Chen <jasonx.z.chen@intel.com>
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CEC receive buffer was not always cleared correctly. The
datasheet was a bit confusing since sometimes it mentioned that the
bit in CEC register 0x4a had to be toggled, and sometimes it suggested
it was a 'Clear-on-write' bit. But it really needs to be toggled.
The patch also enables/disables the CEC irqs after the other irq are
enabled/disabled instead of doing it before. It may not matter, but it
feels more logical to do it in that order, and the implementation that
we (Cisco) have used until now and that is known to be reliable also
did it in that order.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The pixel rate, as reported by the V4L2_CID_PIXEL_RATE control, must
include both horizontal and vertical blanking. Both the AFE and HDMI
receiver program it incorrectly:
- The HDMI receiver goes to the trouble of removing blanking to compute
the rate of active pixels. This is easy to fix by removing the
computation and returning the incoming pixel clock rate directly.
- The AFE performs similar calculation, while it should simply return
the fixed pixel rate for analog sources, mandated by the ADV748x to be
14.3180180 MHz.
[Niklas: Update AFE fixed pixel rate]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
mode_table[] has 3 members that are accessed based on their index, which
makes worth using an array.
The other members are always accessed with a constant index. This added
indirection gives no improvement and only makes code more verbose.
Remove these pointers from the array and access them directly.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Most registers are defined using the name used in the datasheet.
E.g. the defines for the HMAX register are IMX274_HMAX_REG_*.
Rename the SHR and VMAX register accordingly. Also move them close to
related registers: SHR close to SVR, VMAX close to HMAX.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
struct imx274_frmfmt is instantiated only in the imx274_formats[]
array, where imx274_formats[N].mode always equals N (via enum
imx274_mode). So .mode carries no information, and unsurprisingly it
is never used.
mbus_code is never used because the 12 bit modes are not implemented.
The colorspace member is also never used, which is normal since the
imx274 sensor can output only one colorspace.
Let's get rid of all of them.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
imx274_s_frame_interval() already has a direct pointer to the v4l2
exposure control, so reuse it to simplify code.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document the unit to avoid having to look through the code to compute it.
Also clarify that these are min and max values.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The current code decrements the timeout counter i and the end of
each loop i is incremented, so the check for timeout will always
be false and hence the timeout mechanism is just a dead code path.
Potentially, if the RD_READY bit is not set, we could end up in
an infinite loop.
Fix this so the timeout starts from 1000 and decrements to zero,
if at the end of the loop i is zero we have a timeout condition.
Detected by CoverityScan, CID#1324008 ("Logically dead code")
Fixes: ccfc97bdb5 ("[media] smiapp: Add driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov7251 sensor is a 1/7.5-Inch B&W VGA (640x480) CMOS Digital Image
Sensor from Omnivision.
The driver supports the following modes:
- 640x480 30fps
- 640x480 60fps
- 640x480 90fps
Output format is 10bit B&W RAW - MEDIA_BUS_FMT_Y10_1X10.
The driver supports configuration via user controls for:
- exposure and gain;
- horizontal and vertical flip;
- test pattern.
[Sakari Ailus: Wrap a line over 80 characters, fix trivial sparse warning]
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The active frame size is set in the initialization arrays, but the value
itself is also available in the struct ov5640_mode_info.
Let's move these values out of the big bytes arrays, and program it with
the value of the mode that we are given.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All the initialization arrays are changing the horizontal and vertical
totals for some value.
In order to clean up the driver, and since we're going to need that value
later on, let's introduce in the ov5640_mode_info structure the horizontal
and vertical total sizes, and move these out of the bytes array.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The current width and height parameters in the struct ov5640_mode_info are
actually the active horizontal and vertical resolutions.
Since we're going to add a few other parameters, let's pick a better, more
precise name for these values.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SCLK and SCLK2X dividers are fixed in stone in the initialization
array. Let's make explicit what we're doing and move that away from the
huge array to the initialization code.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sensor needs to have the auto exposure stopped while changing mode.
However, when the new mode is set, the driver will force the auto exposure
on, disregarding whether the control has been changed or not.
Bypass the controls code entirely to do that, and only use the control
value cached when restoring the auto exposure mode.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the light frequency control to be able to set the frequency
to manual (50Hz or 60Hz) or auto.
[Sakari Ailus: Rename "ctl" as "ctrl" as agreed.]
[mchehab+samsung@kernel.org: fixed two coding style warnings]
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The s_ctrl() operation can be called when the device is placed into
power down mode. Then, applying controls to H/W should be postponed at
this time. Instead the controls will be restored when the streaming is
started.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The set_fmt() subdev pad operation for this driver currently does not
only do the driver internal format selection but also do the actual
register setup.
This doesn't work if the device power control via GPIO lines is enabled.
Because the set_fmt() can be called when the device is placed into power
down mode.
First of all, this fix adds flag to keep track of whether the device starts
streaming or not. Then, the set_fmt() postpones applying the actual
register setup at this time. Instead the setup will be applied when the
streaming is started.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
I2C transfer functions return number of successful operations (on success).
Do not return the received positive return code but instead return 0 on
success. The users of write_reg function already use this logic.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use dev_fwnode() on the device instead of getting an fwnode handle of the
device's OF node. The result is the same on OF-based systems and looks
better, too.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If 'media_entity_pads_init()' fails, we must free the resources allocated
by 'v4l2_ctrl_handler_init()', as already done in the previous error
handling path.
'goto' the right label to fix it.
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch resolves the following checkpatch.pl error:
ERROR: that open brace { should be on the previous line
Signed-off-by: Nasser Afshin <Afshin.Nasser@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch resolves checkpatch.pl warnings:
WARNING: Block comments use * on subsequent lines
WARNING: Block comments use a trailing */ on a separate line
Signed-off-by: Nasser Afshin <Afshin.Nasser@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Structure i2c_driver does not need to set the owner field, as this will
be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Structure i2c_driver does not need to set the owner field, as this will
be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Cc: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After adding this driver, gcc complains with:
drivers/media/i2c/video-i2c.c:55:1: warning: 'static' is not at beginning of declaration [-Wold-style-declaration]
const static struct v4l2_fmtdesc amg88xx_format = {
^~~~~
drivers/media/i2c/video-i2c.c:59:1: warning: 'static' is not at beginning of declaration [-Wold-style-declaration]
const static struct v4l2_frmsize_discrete amg88xx_size = {
^~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Both Hauppauge WinTV 44981 (bt878) and the HVR 1110 (saa7134) have a Zilog
Z8F0811. The transmitter was not probed. Receive and transmit tested on
both cards.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are several thermal sensors that only have a low-speed bus
interface but output valid video data. This patchset enables support
for the AMG88xx "Grid-Eye" sensor family.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[hans.verkuil@cisco.com: split up int ret = ...->xfer(); line]
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
From now on, I'll start using my @kernel.org as my development e-mail.
As such, let's remove the entries that point to the old
mchehab@s-opensource.com at MAINTAINERS file.
For the files written with a copyright with mchehab@s-opensource,
let's keep Samsung on their names, using mchehab+samsung@kernel.org,
in order to keep pointing to my employer, with sponsors the work.
For the files written before I join Samsung (on July, 4 2013),
let's just use mchehab@kernel.org.
For bug reports, we can simply point to just kernel.org, as
this will reach my mchehab+samsung inbox anyway.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Brian Warner <brian.warner@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Assigning subdev flags in probe() after v4l2_i2c_subdev_init() clears the
I2C flag set by that function. Fix this by using bitwise or instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver has event support implemented but fails to set the flag
enabling event support. Set the flag to enable control events.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check that no error happened during adding controls to the driver's
control handler. Print an error message and bail out if there was one.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check that creating the control actually succeeded before accessing it.
A failure would lead to NULL pointer reference. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver has 12 controls, not 2.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=+PjT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of media updates/fixes for 4.17.
There are two important core fix patches in this series:
- A regression fix on Kernel 4.16 with causes it to not work with
some input devices that depend on media core
- A fix at compat32 bits with causes it to OOPS on overlay, and
affects the Kernels where the CVE-2017-13166 was backported
The remaining ones are other random fixes at the documentation and on
drivers.
The biggest part of this series is a set of 18 patches for the Intel
atomisp driver. Currently, it produces hundreds of warnings/errors on
sparse/smatch, causing me to sometimes ignore new warnings on other
drivers that are not so broken. This driver is on really poor state,
even for staging standards: it has several layers of abstraction on
it, and it supports two different hardware. Selecting between them
require to add a define (there isn't even a Kconfig option for such
purpose). Just on this smatch cleanup, I could easily get rid of 8
"do-nothing" files. So, I'm seriously considering its removal from
upstream, if I don't see any real work on addressing the problems
there along this year"
* tag 'media/v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (48 commits)
media: v4l2-core: fix size of devnode_nums[] bitarray
media: v4l2-compat-ioctl32: don't oops on overlay
media: i2c: adv748x: afe: fix sparse warning
media: extended-controls.rst: transmitter -> receiver
media: staging: atomisp: stop duplicating input format types
media: staging: atomisp: get rid of an unused var
media: staging: atomisp: stop mixing enum types
media: staging: atomisp: get rid of some static warnings
media: staging: atomisp: use %p to print pointers
media: staging: atomisp: remove an useless check
media: staging: atomisp: avoid a warning if 32 bits build
media: staging: atomisp: don't access a NULL var
media: staging: atomisp: Get rid of *default.host.[ch]
media: staging: atomisp: get rid of an unused function
media: staging: atomisp: remove unused set_pd_base()
media: staging: atomisp: fix endianess issues
media: staging: atomisp: add a missing include
media: staging: atomisp: get rid of stupid statements
media: staging: atomisp: declare static vars as such
media: staging: atomisp: ia_css_output.host: don't use var before check
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
kfifo: fix inaccurate comment
tools/thermal: tmon: fix for segfault
net: Spelling s/stucture/structure/
edd: don't spam log if no EDD information is present
Documentation: Fix early-microcode.txt references after file rename
tracing: Block comments should align the * on each line
treewide: Fix typos in printk
GenWQE: Fix a typo in two comments
treewide: Align function definition open/close braces
The output pixel format changed by set_fmt() pad operation is not
correctly applied. It is intended to be restored by calling
ov5640_set_framefmt() when the video stream is started.
However, when the device is powered on by s_power subdev operation before
the video stream is started, the current output mode setting is restored
by ov5640_restore_mode() that also clears pending_mode_change flag in
ov5640_set_mode(). So ov5640_set_framefmt() isn't called as intended and
the output pixel format is not restored.
This change adds the missing output pixel format setting in the
ov5640_restore_mode() that is called when the device is powered on.
Cc: Steve Longerbeam <slongerbeam@gmail.com>
Cc: Hugues Fruchet <hugues.fruchet@st.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Structure i2c_driver does not need to set the owner field, as this will
be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device node obtained with of_graph_get_next_endpoint() should be
released by calling of_node_put(). But it was not released when
v4l2_fwnode_endpoint_parse() failed.
This change moves the of_node_put() call before the error check and
fixes the issue.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix set of missing colorspace related fields in get_/set_fmt.
Detected by v4l2-compliance tool.
[Sakari Ailus: Rearrange fmt declaration in ov5640_probe()]
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
An older version of the driver patches were merged accidentally which
resulted in missing the array_size parameter that tells the length of the
array that contains the different supported sizes.
Bring it back to v4l2_find_nearest size and make the corresponding change
for the drivers using it as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some functions definitions have either the initial open brace and/or
the closing brace outside of column 1.
Move those braces to column 1.
This allows various function analyzers like gnu complexity to work
properly for these modified functions.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There's a false positive warning there:
drivers/media/i2c/tda9840.c:79 tda9840_status() error: uninitialized symbol 'byte'.
Change the code to match our coding style, in order to fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While the code is correct, it produces this warning:
drivers/media/i2c/ir-kbd-i2c.c:593 zilog_ir_format() error: buffer overflow 'code_block->codes' 61 <= 173
As static analyzers may be tricked by arithmetic expressions on
comparisions. So, change the order, in order to shut up this
false-positive warning.
That also makes easier for humans to understand that it won't
be trying to go past buffer size.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current I2C error handling logic makes static analyzers
confused, and it doesn't follow the coding style we're using:
drivers/media/i2c/ir-kbd-i2c.c:180 get_key_pixelview() error: uninitialized symbol 'b'.
drivers/media/i2c/ir-kbd-i2c.c:224 get_key_knc1() error: uninitialized symbol 'b'.
drivers/media/i2c/ir-kbd-i2c.c:226 get_key_knc1() error: uninitialized symbol 'b'.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The error handling logic at tvaudio is broken on several ways,
as it doesn't really check right when an error occurs.
Change it to return the proper error code from read/write
routines and fix the errors on reads.
Shuts up the following warnings:
drivers/media/i2c/tvaudio.c:222 chip_read() error: uninitialized symbol 'buffer'.
drivers/media/i2c/tvaudio.c:223 chip_read() error: uninitialized symbol 'buffer'.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are some troubles on this driver with respect to the usage
of __be16 and __b32 macros:
drivers/media/i2c/ov5670.c:1857:27: warning: incorrect type in initializer (different base types)
drivers/media/i2c/ov5670.c:1857:27: expected unsigned short [unsigned] [usertype] reg_addr_be
drivers/media/i2c/ov5670.c:1857:27: got restricted __be16 [usertype] <noident>
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1901:13: warning: incorrect type in assignment (different base types)
drivers/media/i2c/ov5670.c:1901:13: expected unsigned int [unsigned] [usertype] val
drivers/media/i2c/ov5670.c:1901:13: got restricted __be32 [usertype] <noident>
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove soc_camera framework dependencies from mt9t112 sensor driver.
- Handle clk, gpios and power routines
- Register async subdev
- Remove deprecated g/s_mbus_config operations
- Remove driver flags
- Change driver interface and add kernel doc
- Adjust build system
- Fix code style issues reported by checkpatch in strict mode
This commit does not remove the original soc_camera based driver as long
as other platforms depends on soc_camera framework.
As I don't have access to a working camera module, this change has only
been compile tested.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Copy the soc_camera based driver in v4l2 sensor driver directory.
This commit just copies the original file without modifying it.
No modification to KConfig and Makefile as soc_camera framework
dependencies need to be removed first in next commit.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV7604 has thirteen 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
[Kieran: Re-adapted for mainline]
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has twelve 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has 12 pages mapped onto I2C addresses.
In the existing implementation only 11 are mapped correctly in the page
enumerations, which causes an off-by-one fault on pages above the
infoframe definition due to a missing 'CBUS' page.
This causes the address for the CEC, SDP, TXA, and TXB to be incorrectly
programmed during the iterations in adv748x_initialise_clients().
Until now this has gone un-noticed due to the fact that following the
creation of the clients - the device is reset and the addresses are
reprogrammed in manually by the call to "adv748x_write_regs(state,
adv748x_set_slave_address);"
As part of moving to dynamic i2c address allocations repair this by
providing the missing CBUS page definition.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has identical map configurations for each register map. The
duplication of each map can be simplified using a helper macro such that
each map is represented on a single line.
Define ADV748X_REGMAP_CONF for this purpose use it to create the tables.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/i2c/s5c73m3/s5c73m3-core.c:268 s5c73m3_check_status() error: uninitialized symbol 'status'.
if s5c73m3_check_status() is called too late, time_is_after_jiffies(end)
will return 0, causing the while to abort before reading status.
The current code will do the wrong thing here, as it will still
check if status != value. The right fix here is to change
the logic to ensure that it will always read the status.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cx25840 driver currently configures 885, 887, and 888 using
default divisors for each chip. This check to see if the cx23885
driver has passed the cx25840 a non-default clock rate for a
specific chip. If a cx23885 board has left clk_freq at 0, the
clock default values will be used to configure the PLLs.
This patch only has effect on 888 boards who set clk_freq to 25M.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ">" should be ">=" so that we don't read one element beyond the end
of the array.
Fixes: 8a77009be4 ("media: ov5695: add support for OV5695 sensor")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Update the register 0x3503 to use 'no delay latch' for gain.
This makes sensor to output the first frame as normal rather
than a very dark one.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As the media subdevice is registered with 'v4l2_async_register_subdev()'
unregister it at module removal time with
'v4l2_async_unregister_subdev()'
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
msleep() can sleep up to 20ms.
As suggested by Documentation/timers/timers_howto.txt replace it with
usleep_range() with up to 5ms delay.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add an empty line before return at the end of functions.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A lot of comments that would fit a single line were spread on two or
more lines. Also fix capitalization and punctuation where appropriate.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Align all function parameters to first open brace when declaring
functions.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
msleep() can sleep up to 20ms.
As suggested by Documentation/timers/timers_howto.txt replace it with
usleep_range() with up to 5ms delay.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Two minor style fixes, align function parameter and remove un-necessary
spaces.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Yet more whitespace and style neatening
o Add blank lines before returns
o Reverse a logic test and return early on error
o Move formats to same line as dev_<level> calls
o Remove an unnecessary period from a logging message
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Update multiline statements to open parenthesis.
Update a ?: to a single line.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A lot of comments that would fit a single line were spread on two or
more lines. Also fix capitalization and punctuation where appropriate.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* commit 'v4.16-rc4~0': (900 commits)
Linux 4.16-rc4
memremap: fix softlockup reports at teardown
libnvdimm: re-enable deep flush for pmem devices via fsync()
MAINTAINERS: take over Kconfig maintainership
vfio: disable filesystem-dax page pinning
kconfig: fix line number in recursive inclusion error message
Coccinelle: memdup: Fix typo in warning messages
i2c: octeon: Prevent error message on bus error
parisc: Reduce irq overhead when run in qemu
parisc: Use cr16 interval timers unconditionally on qemu
parisc: Check if secondary CPUs want own PDC calls
parisc: Hide virtual kernel memory layout
parisc: Fix ordering of cache and TLB flushes
kconfig: Update ncurses package names for menuconfig
kbuild/kallsyms: trivial typo fix
kbuild: test --build-id linker flag by ld-option instead of cc-ldoption
kbuild: drop superfluous GCC_PLUGINS_CFLAGS assignment
kconfig: Don't leak choice names during parsing
sh: fix build error for empty CONFIG_BUILTIN_DTB_SOURCE
kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list
...
Without CONFIG_PM, we get a harmless build warning:
drivers/media/i2c/ov2685.c:516:12: error: 'ov2685_runtime_suspend' defined but not used [-Werror=unused-function]
static int ov2685_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/ov2685.c:507:12: error: 'ov2685_runtime_resume' defined but not used [-Werror=unused-function]
static int ov2685_runtime_resume(struct device *dev)
This marks the affected functions as __maybe_unused.
Fixes: e3861d9118 ("media: ov2685: add support for OV2685 sensor")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[hans.verkuil@cisco.com: fixed typo in Subject: was ov5695]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without CONFIG_PM, we get a harmless build warning:
drivers/media/i2c/ov5695.c:1033:12: error: 'ov5695_runtime_suspend' defined but not used [-Werror=unused-function]
static int ov5695_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/ov5695.c:1024:12: error: 'ov5695_runtime_resume' defined but not used [-Werror=unused-function]
static int ov5695_runtime_resume(struct device *dev)
This marks the affected functions as __maybe_unused.
Fixes: 8a77009be4 ("media: ov5695: add support for OV5695 sensor")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without CONFIG_SND, we get a link error:
ERROR: "snd_soc_register_codec" [drivers/media/i2c/tda1997x.ko] undefined!
ERROR: "snd_soc_unregister_codec" [drivers/media/i2c/tda1997x.ko] undefined!
ERROR: "snd_pcm_hw_constraint_minmax" [drivers/media/i2c/tda1997x.ko] undefined!
This adds the same Kconfig dependency that we have in other
media drivers, using 'select SND_PCM' to ensure that we have
can call snd_pcm_hw_constraint_minmax, while depending on
CONFIG_SND_SOC for registering the codec.
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The error handling for the adv748x_identify_chip() call erroneously
jumps to the err_cleanup_clients label before the clients have been
established.
Correct this by jumping to the next (and correct) label in the cleanup
code: err_cleanup_dt.
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're adding this as a new driver, make checkpatch happier by
solving several style issues, using --fix-inplace at strict mode.
Some issues required manual work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're adding this as a new driver, make checkpatch happier by
solving some whitespace issues, using --fix-inplace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove soc_camera framework dependencies from tw9910 sensor driver.
- Handle clock and gpios
- Register async subdevice
- Remove soc_camera specific g/s_mbus_config operations
- Add kernel doc to driver interface header file
- Adjust build system
This commit does not remove the original soc_camera based driver as long
as other platforms depends on soc_camera-based CEU driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Copy the soc_camera based driver in v4l2 sensor driver directory.
This commit just copies the original file without modifying it.
No modification to KConfig and Makefile as soc_camera framework
dependencies need to be removed first in next commit.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support to ov772x driver for frame intervals handling and enumeration.
Tested with 10MHz and 24MHz input clock at VGA and QVGA resolutions for
10, 15 and 30 frame per second rates.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove soc_camera framework dependencies from ov772x sensor driver.
- Handle clock and gpios
- Register async subdevice
- Remove soc_camera specific g/s_mbus_config operations
- Change image format colorspace from JPEG to SRGB as the two use the
same colorspace information but JPEG makes assumptions on color
components quantization that do not apply to the sensor
- Remove sizes crop from get_selection as driver can't scale
- Add kernel doc to driver interface header file
- Adjust build system
This commit does not remove the original soc_camera based driver as long
as other platforms depends on soc_camera-based CEU driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Copy the soc_camera based driver in v4l2 sensor driver directory.
This commit just copies the original file without modifying it.
No modification to KConfig and Makefile as soc_camera framework
dependencies need to be removed first in next commit.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Solve the following warnings:
+ drivers/media/i2c/tvp514x.c: warning: Excess function parameter 'a' description in 'tvp514x_g_frame_interval': => 759
+ drivers/media/i2c/tvp514x.c: warning: Excess function parameter 'a' description in 'tvp514x_s_frame_interval': => 784
+ drivers/media/i2c/tvp514x.c: warning: Function parameter or member 'ival' not described in 'tvp514x_g_frame_interval': => 759
+ drivers/media/i2c/tvp514x.c: warning: Function parameter or member 'ival' not described in 'tvp514x_s_frame_interval': => 784
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix this warning regression:
drivers/media/i2c/ov7740.c: warning: variable 'ret' set but not used [-Wunused-but-set-variable]: => 276:6
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x handles interlaced media using V4L2_FIELD_ALTERNATE field
types. The correct specification for the height on the mbus is the
image height, in this instance, the field height.
The AFE component already correctly adjusts the height on the mbus, but
the HDMI component got left behind.
Adjust the mbus height to correctly describe the image height of the
fields when processing interlaced video for HDMI pipelines.
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add suffix LL to constant 2 in order to give the compiler complete
information about the proper arithmetic to use. Notice that this
constant is used in a context that expects an expression of type
s64 (64 bits, signed).
The expression 2 * (clock_rate - abs_nco_freq) is currently being
evaluated using 32-bit arithmetic.
Addresses-Coverity-ID: 1446589 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As pointed by Dan, possible values for bits[3:0] of te Line Mode Registers
can range from 0x0 to 0xf, but the check logic allow values ranging
from 0x0 to 0xe.
As static arrays are initialized with zero, using a value without
an explicit initializer at the array won't cause any harm.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
After a framerate update through s_frame_interval(), the new
framerate was not taken into account when streaming,
but was taken into account on next session.
This was due to sensor->current_mode not updated accordingly to new
framerate setting in ov5640_s_frame_interval().
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix module_param(virtual_channel) permissions.
This problem was detected by checkpatch:
$ scripts/checkpatch.pl -f drivers/media/i2c/ov5640.c
ERROR: Use 4 digit octal (0777) not decimal permissions
+module_param(virtual_channel, int, 0);
Also add an error trace in case of virtual_channel not in
the valid range of values.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Various typo & style fixes either detected by code
review or checkpatch.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add an error trace in ov5640_read_reg() in case of i2c_transfer()
failure.
Uniformize error traces using dev_err instead v4l2_err.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ov7670 driver supports two optional properties supplied through platform
data, but currently does not support any standard video interface
property.
Add support through OF parsing for 2 generic properties (vsync and hsync
polarities) and for one custom property already supported through
platform data to suppress pixel clock output during horizontal
blanking.
While at there, check return value of register writes in set_fmt
function and rationalize spacings.
Signal polarities and pixel clock blanking verified through scope and
image capture.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cast fi->interval.numerator to u64 in order to avoid a potential integer
overflow. This variable is being used in a context that expects an
expression of type u64.
Addresses-Coverity-ID: 1324146 ("Unintentional integer overflow")
[Sakari Ailus: use do_div() to make this work on 32-bit systems]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov9650 driver currently only supports legacy platform data probe.
This change adds device tree probing.
There has been an attempt to add device tree support for ov9650 driver
by Hugues Fruchet as a part of the patchset that adds support of OV9655
camera (http://www.spinics.net/lists/linux-media/msg117903.html), but
it wasn't merged into mainline because creating a separate driver for
OV9655 is preferred.
This is very similar to Hugues's patch, but not supporting new device.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Hugues Fruchet <hugues.fruchet@st.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Rob Herring <robh@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, the sensor, with default settings, was outputting SOF without
data. This results in frame sync error on the receiver side.
Now, configure the sensor to output SOF with MIPI data for all frames. This
avoids possible null first frame on the bus.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Assign ret in the default case for s_ctrl callback. This can't happen but
still may result in compiler warnings.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds driver for Omnivision's ov2685 sensor.
Though the ov2685 can output yuv data, this driver only
supports the raw bayer format, including the following features:
- output 1600x1200 at 30fps
- test patterns
- manual exposure/gain control
- vblank and hblank
- media controller
- runtime pm
[Sakari Ailus: trivial: ov5695_of_match -> ov2685_of_match]
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds driver for Omnivision's ov5695 sensor,
the driver supports following features:
- supported resolutions
+ 2592x1944 at 30fps
+ 1920x1080 at 30fps
+ 1296x972 at 60fps
+ 1280x720 at 30fps
+ 640x480 at 120fps
- test patterns
- manual exposure/gain(analog and digital) control
- vblank and hblank
- media controller
- runtime pm
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver is unused and depends on the deprecated soc-camera framework.
Move it to staging in preparation for being removed unless someone does
the work to convert it to a proper V4L2 subdev driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver is unused and depends on the deprecated soc-camera framework.
Move it to staging in preparation for being removed unless someone does
the work to convert it to a proper V4L2 subdev driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
1 warning regressions:
+ drivers/media/i2c/tda1997x.c: warning: variable 'last_irq_status' set but not used [-Wunused-but-set-variable]: => 1421:17
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the TDA1997x HDMI receivers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix type 'testin' -> 'testing']
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert all g/s_parm calls to g/s_frame_interval. This allows us
to remove the g/s_parm ops since those are a duplicate of
g/s_frame_interval.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the old license information with the corresponding SPDX
license for those drivers Cisco authored.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When built on a platform without gpiolib support, we run into
a couple of compile errors in ov7740, including:
drivers/media/i2c/ov7740.c: In function 'ov7740_set_power':
drivers/media/i2c/ov7740.c:307:4: error: implicit declaration of function 'gpiod_direction_output'; did you mean 'gpio_direction_output'? [-Werror=implicit-function-declaration]
gpiod_direction_output(ov7740->pwdn_gpio, 0);
drivers/media/i2c/ov7740.c:914:4: error: 'GPIOD_OUT_HIGH' undeclared (first use in this function); did you mean 'GPIOF_INIT_HIGH'?
Changing it to use the correct header file solves the problem.
Fixes: 39c5c4471b ("media: i2c: Add the ov7740 image sensor driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add nop variant of media_entity_cleanup. This allows calling
media_entity_cleanup whether or not Media controller is enabled,
simplifying driver code.
Also drop #ifdefs on a few drivers around media_entity_cleanup().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Time to time, stream on is failing with a strange positive error.
Error code is returned erroneously by ov5640_set_ctrl_exposure()
due to ov5640_get_vts() return value wrongly treated as error.
Fix this by forcing ret to 0 after ov5640_get_vts() success call,
in order that ret is set to success for rest of code sequence.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned:
drivers/media/i2c/dw9714.c: warning: incorrect type in initializer (different base types): => 64:19
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The client field in driver's struct is redundant. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Call pm_runtime_idle() at the end of the driver's probe() function to
enable the device to reach low power state once probe() finishes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support of DVP parallel mode in addition of
existing MIPI CSI mode. The choice between two modes
and configuration is made through device tree.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mt9m111 has the test pattern generator features. This makes use of
it through V4L2_CID_TEST_PATTERN control.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Create a source pad and set the media controller type to the sensor.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so that the
subdevice device node is created.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov7740 (color) image sensor is a high performance VGA CMOS
image snesor, which supports for output formats: RAW RGB and YUV
and image sizes: VGA, and QVGA, CIF and any size smaller.
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Smatch complains that "err" can be uninitialized if we have a zero size
write. The flow analysis is a little complicated so I'm not sure if
that's possible or not, but it's harmless to set this to zero and it
makes the code easier to read.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a lot of places where sequences of space/tabs are
found. Get rid of all spaces before tabs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On several places, whitespaces are being used for indentation,
or even at the end of the line.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove the V4L2 AS3645A sub-device driver in favour of the LED flash class
driver for the same hardware, drivers/leds/leds-as3645a.c. The latter uses
the V4L2 flash LED class framework to provide V4L2 sub-device interface.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most of the I2C headers got moved a long time ago to
include/media/i2c. Stop including them at the patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the past, the same I2C address were used on multiple places.
After I2C rebinding changes, this is no longer needed. So, we
can just get rid of this header, placing the I2C address where
they belong, e. g. either at bttv driver or at tvtuner.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a fix for commit 329d88da4d ("[media] media: i2c: Don't export
ir-kbd-i2c module alias") that stopped the module from being loaded
automagically.
The problems described only affect the HD-PVR, so it should not affect
other hardware; also if the module happens to be loaded, the i2c IR
part of the HD-PVR will be enabled anyway.
Fixes: 329d88da4d ("[media] media: i2c: Don't export ir-kbd-i2c module alias")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This code implements the transmitter which is currently implemented
in the staging lirc_zilog driver.
The new code does not need a signal database, iow. the
haup-ir-blaster.bin firmware file is no longer needed, and the driver
does not know anything about the keycodes in that file.
Instead, the new driver can send raw IR, but the hardware is limited
to few different lengths of pulse and spaces, so it is best to use
generated IR rather than recorded IR.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These two devices ids are really just one device with multiple
addresses. Probing becomes much simpler if we simply fold this into
one i2c device with two address.
Note that this breaks the lirc_zilog driver, however we will teach
ir-kbd-i2c to do what lirc_zilog does in a later commit.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The lirc_zilog driver only polls the device if the lirc chardev
is opened; do the same with the rc-core driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the dev_dbg dynamic infrastructure instead of rolling our own custom
debug logic.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Marco Felsch