This adds the support of atmel-mci sd/mmc driver in at91sam9g45 devices and
board files. This also configures the DMA controller slave interface for
at_hdmac dmaengine driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This driver adds basic support for the esdhc-core found on e.g.
imx35/51, as a platform driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix kconfig dependency warning to satisfy dependencies:
warning: (MMC_CB710 && MMC && PCI) selects CB710_CORE which has
unmet direct dependencies (MISC_DEVICES && PCI)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a driver for USB SD Host Controller devices. These devices are
Cypress Astoria chips with firmware compliant with issue 2 of CSR's USHC
specification.
[cjb: adapt to block layer deprecation of max_{hw,phys}_segs]
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'msm-mmc_sdcc' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
mmc: msm_sdcc: Rename config MMC_MSM7X00A to MMC_MSM
mmc: msm_sdcc: Compile the driver for msm7x30
mmc: msm: fix up build breakage on !PM
There's nothing special, just SoC-specific ops and quirks.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Richard R?jfors <richard.rojfors@pelagicore.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SD/MMC host controller driver is same for all MSM and QSD
platforms. Hence, rename the config to reflect the same.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The controller base address is referred from platform
resource instead of using #defines. This fixes the
compilation error when driver is compiled for msm7x30.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
MSM7x30 isn't supported in this driver yet. If ones tried to compile it in
with MSM7x30 configure you get,
linux-2.6/drivers/mmc/host/msm_sdcc.c: In function 'msmsdcc_fifo_addr':
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: 'MSM_SDC1_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: (Each undeclared identifier is reported only once
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: for each function it appears in.)
linux-2.6/drivers/mmc/host/msm_sdcc.c:167: error: 'MSM_SDC2_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:169: error: 'MSM_SDC3_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:171: error: 'MSM_SDC4_PHYS' undeclared (first use in this function)
So we add a Kconfig check to prevent this.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add a glue layer to support the sdhci driver on the ST SPEAr platform.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: <shiraz.hashim@st.com>
Cc: Linus Walleij <linus.ml.walleij@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MMCIF is the MMC Host Interface in SuperH.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable the sh_mobile_sdhi mfd driver on SH-Mobile ARM
processors. While at it, make CONFIG_TMIO_MMC depend on
CONFIG_MFD_SH_MOBILE_SDHI.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The host/Kconfig file is only included when MMC is selected.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This prevents those without an Atmel chip having a line in kernel
configuration which says "Atmel SD/MMC Driver" without any option.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch solves nasty problem original driver has.
Original goal of the ricoh_mmc was to disable this device because then,
mmc cards can be read using standard SDHCI controller, thus avoiding
writing of yet another driver.
However, the act of disablement, makes other pci functions that belong to
this controller (xD and memstick) shift up one level, thus pci core has
now wrong idea about these devices.
To fix this issue, this patch moves the driver into the pci quirk section,
thus it is executes before the pci is enumerated, and therefore solving
that issue, also same sequence of commands is performed on resume for same
reasons.
Also regardless of the above, this way is cleaner. You still need to set
CONFIG_MMC_RICOH_MMC to enable this quirk
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Philip Langdale <philipl@overt.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Secure Digital Host Controller Interface found on the
"Hollywood" chipset of the Nintendo Wii video game console.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch breaks down sdhci-of into a core portion and a eSDHC portion,
clearing the path to easily support additional hardware using the same OF
driver.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for MMC/SD controller driver for all DaVinci family SoC. This
patch supports davinci family SoC's DM6446, DM355, DM365 and
DA830/OMAPL137.
The patch has been tested on DM355 EVM.
The MMCSD controller specifications for DM355 can be found at
http://focus.ti.com/general/docs/litabsmultiplefilelist.tsp?literatureNumber=spruee2c
Signed-off-by: Vipin Bhandari <vipin.bhandari@ti.com>
Signed-off-by: Purshotam Kumar <purushotam@ti.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add SUPERH to the Kconfig dependencies for tmio_mmc.
This change allows us to drive the SDHI hardware blocks
found in SuperH Mobile with tmio_mmc.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We have found a couple of boards where the SDIO IRQ hardware support has
failed to work properly, and thus we should make it configurable whether
or not to be included in the driver.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a selection for the data transfer mode of the s3cmci driver, allowing
for either a configuration or rumtime selection of the use of the DMA or
PIO transfer code.
The PIO only mode is 476 bytes smaller than the driver with both methods
compiled in.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add basic support for all 5 MMC controllers on OMAP4.
This patch doesn't include mmc-regulator support
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unification of the atmel-mci driver to support the AT91 processors MCI
interface. The atmel-mci driver currently supports the AVR32 and this
patch adds AT91 support.
Add read/write proof selection switch dependent on chip availability of
this feature.
To use this new driver on a at91 the platform driver for your board needs
to be updated.
[nicolas.ferre@atmel.com indent, Kconfig comment and one printk modification]
Signed-off-by: Rob Emanuele <rob@emanuele.us>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MMC Driver for HTC Dream. I picked the code up from Google git trees,
removed stuff not strictly necessary, and did a few cleanups. It still
works :-).
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Joe Perches <joe@perches.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the via-sdmmc driver for the SD/MMC-controller of VIA,
which is found in a number of recent integrated VIA chipset
products.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Add support for the 'HSMMC' block(s) in the Samsung SoC
line. These are compatible with the SDHCI driver so add
the necessary setup and driver binding for the platform
devices.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (25 commits)
atmel-mci: add MCI2 register definitions
atmel-mci: Integrate AT91 specific definition in header file
tmio_mmc: allow compilation for ASIC3
mmc_block: do not DMA to stack
sdhci: Print ADMA status and pointer on debug
tmio_mmc: fix clock setup
tmio_mmc: map SD control registers after enabling the MFD cell
tmio_mmc: correct probe return value for num_resources != 3
tmio_mmc: don't use set_irq_type
tmio_mmc: add bus_shift support
MFD,mmc: tmio_mmc: make HCLK configurable
mmc_spi: don't use EINVAL for possible transmission errors
cb710: more cleanup for the DEBUG case.
sdhci: platform driver for SDHCI
mxcmmc: remove frequency workaround
cb710: handle DEBUG define in Makefile
cb710: add missing parenthesis
cb710: fix printk format string
mmc: Driver for CB710/720 memory card reader (MMC part)
pxamci: add regulator support.
...
Now tmio_mmc is able to drive the MMC/SD cell in ASIC3.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Added a platform driver which uses the SDHCI core.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
arch-imx is superseeded by the MXC architecture support.
This patch removes arch-imx from the build system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (42 commits)
atmel-mci: fix sdc_reg typo
tmio_mmc: add maintainer
mmc: Add OpenFirmware bindings for SDHCI driver
sdhci: Add quirk for forcing maximum block size to 2048 bytes
sdhci: Add quirk for controllers that need IRQ re-init after reset
sdhci: Add quirk for controllers that need small delays for PIO
sdhci: Add set_clock callback and a quirk for nonstandard clocks
sdhci: Add get_{max,timeout}_clock callbacks
sdhci: Add support for hosts reporting inverted write-protect state
sdhci: Add support for card-detection polling
sdhci: Enable only relevant (DMA/PIO) interrupts during transfers
sdhci: Split card-detection IRQs management from sdhci_init()
sdhci: Add support for bus-specific IO memory accessors
mmc_spi: adjust for delayed data token response
omap_hsmmc: Wait for SDBP
omap_hsmmc: Fix MMC3 dma
omap_hsmmc: Disable SDBP at suspend
omap_hsmmc: Do not prefix slot name
omap_hsmmc: Allow cover switch to cause rescan
omap_hsmmc: Add 8-bit bus width mode support
...
This patch adds a new driver: sdhci-of. The driver is similar to
the sdhci-pci, it contains common probe code, and controller-specific
ops and quirks.
So far there are only Freescale eSDHC ops and quirks.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently the SDHCI driver works with PCI accessors (write{l,b,w} and
read{l,b,w}).
With this patch drivers may change memory accessors, so that we can
support hosts with "weird" IO memory access requirments.
For example, in "FSL eSDHC" SDHCI hardware all registers are 32 bit
width, with big-endian addressing. That is, readb(0x2f) should turn
into readb(0x2c), and readw(0x2c) should be translated to
le16_to_cpu(readw(0x2e)).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This supports MMC/SD/SDIO currently found on the Kirkwood 88F6281 and
88F6192 SoC controllers.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add omap hsmmc controller for 2430 and 34xx.
Note that this controller has different registers compared to
the earlier omap MMC controller, so sharing code currently is
not possible.
Various updates and fixes from linux-omap list have been
merged into this patch.
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds support for DMA transfers through the generic DMA engine
framework with the DMA slave extensions.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 7.5 MiB/s on fast cards with debugging disabled.
Unfortunately, the driver has been known to lock up from time to time
with DMA enabled, so DMA support is currently optional and marked
EXPERIMENTAL. However, I didn't see any problems while testing 13
different cards (MMC, SD and SDHC of different brands and sizes), so I
suspect the "Initialize BLKR before sending data transfer command" fix
that was posted earlier fixed this as well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The TMIO chips are only found (and thus tested) on ARM machines.
Moreover, we don't want the TMIO cells to be built if one of the TMIO
driver is not selected (which indirectly make the TMIO cells drivers
depend on ARM as well).
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds support for the MMC subdevice 'cell' commonly found in
TMIO based MFDs.
Signed-off-by: Ian Molton <spyro@f2s.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This is a driver for the MMC controller on the AP7000 chips from
Atmel. It should in theory work on AT91 systems too with some
tweaking, but since the DMA interface is quite different, it's not
entirely clear if it's worth merging this with the at91_mci driver.
This driver has been around for a while in BSPs and kernel sources
provided by Atmel, but this particular version uses the generic DMA
Engine framework (with the slave extensions) instead of an
avr32-only DMA controller framework.
This driver can also use PIO transfers when no DMA channels are
available, and for transfers where using DMA may be difficult or
impractical for some reason (e.g. the DMA setup overhead is usually
not worth it for very short transfers, and badly aligned buffers or
lengths are difficult to handle.)
Currently, the driver only support PIO transfers. DMA support has been
split out to a separate patch to hopefully make it easier to review.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 3.5 MiB/s on fast cards with debugging disabled.
The driver has also been tested using the mmc_test module on the same
cards. All tests except 7, 9, 15 and 17 succeed. The first two are
unsupported by all the cards I have, so I don't know if the driver
handles this correctly. The last two fail because the hardware flags a
Data CRC Error instead of a Data Timeout error. I'm not sure how to deal
with that.
Documentation for this controller can be found in many data sheets from
Atmel, including the AT32AP7000 data sheet which can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This is the latest S3C MMC/SD driver by Thomas Kleffel
with cleanups as suggested by AKPM done by Ben Dooks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The SDHCI interface is not PCI specific, yet the Linux driver was
intimitely connected to the PCI bus. This patch properly separates
the PCI specific portion from the bus independent code.
This patch is based on work by Ben Dooks but he did not have time
to complete it.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Both of these drivers work well (although some hardware still has
its problems) and are not in the "alpha" quality that EXPERIMENTAL
suggests.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Thanks to Matt Domsch and Rezwanul Kabir at Dell, we know how to disable the
MMC controller on the multi-function Ricoh R5C832. The MMC controller needs
to be disabled or it will steal MMC cards from the SD controller where they
would otherwise be supported by the Linux SDHCI driver.
Signed-off-by: Philipl Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This is the latest version of the MMC-over-SPI support. It works
on 2.6.23-rc2 plus git-mmc (from rc1-mm2), along with the preceding
patches which teach the rest of the MMC stack about SPI.
The main issue of note is that sometimes cards need to be power cycled
to recover after certain faults. Also, it may sometimes be necessary
to disable CRCs. ("modprobe mmc_core use_spi_crc=n")
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: mikael.starvik@axis.com,
Cc: Hans-Peter Nilsson <hp@axis.com>
Cc: Jan Nikitenko <jan.nikitenko@gmail.com>
Cc: Mike Lavender <mike@steroidmicros.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Nicolas Ferre