CC [M] drivers/net/wireless/b43/pio.o
drivers/net/wireless/b43/pio.c: In function ‘pio_rx_frame’:
drivers/net/wireless/b43/pio.c:614:6: warning: ‘macstat’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't know yet when to restore it, implement just reading. We found
out what for are that PHY ops by comparing HT with N code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Comparison of the HT and N code has shown similarities in the ops
performed after b43_mac_phy_clock_set. That way we understood what is
happening in the HT-PHY code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have module param called use_pio which is much easier to use.
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the "FWxx" ID strings from the b43 and b43legacy
drivers. They were once used to match a specific driver revision
to a set of firmware files. However, this is hardly useful today.
Additionally, the IDs are not updated and maintained properly, so
they might mislead users.
Signed-off-by: Michael Buesch <m@bues.ch>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have resolved all the known issues with DMA mode, however some users
(or distros) are still forcing PIO mode by config files. Without
debugging enabled it's not noticable at all. Add the warning for them.
Cc: Gregory Bellier <gregory.bellier@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They were taken from MMIO dump with few RegExps and vim.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Analog is switched on right after reading PHY version:
read16 0xfaafc3e0 -> 0xa801
phy_read(0x043b) -> 0x0000
phy_write(0x043b) <- 0x0000
Switched off after after killing radio:
>>> Switch Radio(OFF) end
phy_read(0x043c) -> 0x0000
phy_write(0x043c) <- 0x0007
phy_read(0x043b) -> 0x0000
phy_write(0x043b) <- 0x0007
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware with 64-bit DMA uses lower address word for setting
routing (translation) bit. Add workaround for such boards.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes we need to write table which is 2-10 elements long. It's
easier to create such a function instead of defining array every time.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MMIO hacks were used to trick ndis&wl. For example following:
phy_read(0x0280) -> 0xffff
phy_write(0x0280) <- 0xff3e
***
phy_read(0x0280) -> 0x0000
phy_write(0x0280) <- 0x003e
was translated to mask 0xff00 and set 0x3e.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace "old" and "new" with number of the first firmware known to use
the given format.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
b43_op_config and b43_op_bss_info_changed apply many settings by directly
writing to hardware registers. These settings are lost as soon as the core
is restarted and the initvals are reloaded. This was discovered because
restarting hostapd led to the beacon interval getting set to ~33s (see
https://dev.openwrt.org/ticket/8033 for more information).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since kernel 3.0, the problems with controlling b43 devices that have
low-power (LP) PHYs have been fixed and the EXPERIMENTAL designation
can be fixed.
This patch also fixes a typo as the device supports 802.11b communications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ieee80211 core was found on a Netgear wndr3400.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
linux/wireless.h and net/iw_handler.h headers are
for wireless extensions only, so mac80211 drivers
shouldn't be including them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wldev is freed in b43_one_core_detach() and should not be accessed after
that call. Keep wldev->dev in a local variable.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've fixed the last issue with BCMA support which caused memory
corruption on loading and unloading b43. Support for BCMA in b43 was
tested with 14e4:4353, 14e4:4357, 14e4:4727 and 14e4:4331. First two
cards (BCM43224 and BCM43225) are supported.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
Remove b43's workarounds at the same time. Other users of
ssb_dma_translation do not support any 64-bit DMA devices, so they are
not affected.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Analyze of MMIO dumps from BCM43224, BCM43225, BCM4313 and BCM4331 has
shown that wl disables parity check for all that cards. This is required
for receiving any packets from the hardware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the newer Broadcom chipsets have longe names like BCM43224,
BCM43225, etc. However Broadcom decided to keep using u16 for storing
them. Use %X or %d depending on chip_id value to avoid BCMA8D8, etc.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Old masks were causing ugly, delayed lock ups.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following operation was incorrectly translated:
radio_read(0x0011) -> 0xffff
radio_write(0x0011) <- 0xfff7
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also change the default channel to 11. This is the first channel closed
driver switches to.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville