Another round of 'allOf' removals that came in this cycle.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Signed-off-by: Rob Herring <robh@kernel.org>
Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
Note, you will get a conflict merging with your tree in the
Documentation/devicetree/bindings/serial/rs485.yaml file, but it should
be pretty obvious what to do. If not, I'm sure Rob will clean it all up
afterwards :)
All of these have been in linux-next with no issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzpCg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRxACgjGtOKPjahONL4lWd0F8ZYEcyw7sAn34woBCO
BDUV3kolrRQ4OYNJWsHP
=TvqG
-----END PGP SIGNATURE-----
Merge tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
All of these have been in linux-next with no issues for a while"
* tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (67 commits)
tty: serial: qcom_geni_serial: Add 51.2MHz frequency support
tty: serial: imx: clear Ageing Timer Interrupt in handler
serial: 8250_fintek: Add F81966 Support
sc16is7xx: Add flag to activate IrDA mode
dt-bindings: sc16is7xx: Add flag to activate IrDA mode
serial: 8250: Support rs485 bus termination GPIO
serial: 8520_port: Fix function param documentation
dt-bindings: serial: Add binding for rs485 bus termination GPIO
vt: keyboard: avoid signed integer overflow in k_ascii
serial: 8250: Enable 16550A variants by default on non-x86
tty: hvc_console, fix crashes on parallel open/close
serial: imx: Initialize lock for non-registered console
sc16is7xx: Read the LSR register for basic device presence check
sc16is7xx: Allow sharing the IRQ line
sc16is7xx: Use threaded IRQ
sc16is7xx: Always use falling edge IRQ
tty: n_gsm: Fix bogus i++ in gsm_data_kick
tty: n_gsm: Remove unnecessary test in gsm_print_packet()
serial: stm32: add no_console_suspend support
tty: serial: fsl_lpuart: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
...
Add documentation to support RX-TX & CTS-RTS GPIO pin swap in HW.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This series of uart controllers is able to work in IrDA mode.
This adds a property to the device tree to enable that feature on
selected ports if needed.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200529055058.1606910-2-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e8759ad17d ("serial: uapi: Add support for bus termination")
introduced the ability to enable rs485 bus termination from user space.
So far the feature is only used by a single driver, 8250_exar.c, using a
hardcoded GPIO pin specific to Siemens IOT2040 products.
Provide for a more generic solution by allowing specification of an
rs485 bus termination GPIO pin in the device tree. An upcoming commit
implements support for this pin for any 8250 driver. The binding is
used in device trees of the "Revolution Pi" PLCs offered by KUNBUS.
[Heiko Stuebner converted the binding to YAML, hence his Signed-off-by.]
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/4f4411895dc52c846f766e7f7207ec412c4811b6.1589811297.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document Device Tree bindings for the Renesas EMMA Mobile UART
Interface.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Rob Herring <robh@kernel.org>
The conversion to json-schema accidentally retained some SoC part
numbers in comments for compatible values. Drop them, as they're part
of the compatible values anyway.
Fixes: 384d00fae8 ("dt-bindings: serial: sh-sci: Convert to json-schema")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
RZ/G1H (R8A7742) SoC also has the R-Car gen2 compatible SCIFA ports,
so document the SoC specific bindings.
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Document the use of CTS/RTS gpios for flow control in STM32 UART
controller. These properties can be used instead of 'st,hw-flow-ctrl'
for making use of any gpio pins for flow control instead of dedicated
pins. It should be noted that both CTS/RTS and 'st,hw-flow-ctrl'
properties cannot co-exist in a design.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200420170204.24541-2-mani@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The examples template is a 'simple-bus' with a size of 1 cell for
had between 2 and 4 cells which really only errors on I2C or SPI type
devices with a single cell.
The easiest fix in most cases is to change the 'reg' property to for 1 cell
address and size. In some cases with child devices having 2 cells, that
doesn't make sense so a bus node is needed.
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
RZ/G1H (R8A7742) SoC also has the R-Car gen2 compatible HSCIF ports,
so document the SoC specific bindings.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
RZ/G1H (R8A7742) SoC also has the R-Car gen2 compatible SCIFB ports,
so document the SoC specific bindings.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
RZ/G1H (R8A7742) SoC also has the R-Car gen2 compatible SCIF ports,
so document the SoC specific bindings.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the ingenic,uart.txt to a new ingenic,uart.yaml file.
A few things were changed in the process:
- the dmas and dma-names properties are now required.
- the ingenic,jz4770-uart and ingenic,jz4775-uart compatible strings now
require the ingenic,jz4760-uart string to be used as fallback, since
the hardware is compatible.
- the ingenic,jz4725b-uart compatible string was added, with a fallback
to ingenic,jz4740-uart.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a description for reg-io-width options for the samsung serial
UART peripheral.
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200506080242.18623-2-hyunki00.koo@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Scripted with ruamel.yaml with some manual fixups. Some minor whitespace
changes from the script.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Stephen Boyd <sboyd@kernel.org> # clock
Signed-off-by: Rob Herring <robh@kernel.org>
Some fixes were done during the conversion:
Slightly better examples. The original example was for an OMAP serial
port, which is not even described by this binding, but by
omap_serial.txt instead.
Added compatible strings, that were used, byt not documented:
andestech,uart16550, cavium,octeon-3860-uart, fsl,16550-FIFO64,
nvidia,tegra186-uart, nvidia,tegra194-uart, nxp,lpc1850-uart,
opencores,uart16550-rtlsvn105, ralink,mt7620a-uart, ralink,rt3052-uart,
ralink,rt3883-uart and xlnx,xps-uart16550-2.00.b.
Removed "serial" compatible string. It's redundant with the node name
(which, in OFW, serves the same purpose as the compatible string).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
[robh: allow additional properties. clocks/clock-frequency can be
optional on original 8250 series with standard clocks]
Signed-off-by: Rob Herring <robh@kernel.org>
These ports are compatible with NS8250 and handled by the same driver.
Get rid of the extra document that fails to document the properties that
are actually supported.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Rob Herring <robh@kernel.org>
Fix various inconsistencies in schema indentation. Most of these are
list indentation which should be 2 spaces more than the start of the
enclosing keyword. This doesn't matter functionally, but affects running
scripts which do transforms on the schema files.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAl6GTJUQHHJvYmhAa2Vy
bmVsLm9yZwAKCRD6+121jbxhw8vaD/9HDT0EEDRdfr8s5OiLHYQMSXlSExJgR+ON
iLI4v19apWwyycil176RXuWL5fFxh9HHOKbxOL27mmfqSLdv/xe/ev6Z4oNLVZzm
YiUalm37K+R9yWsWTqxJKtQxWqSBBtOlyJmUYnvxI1bjfF4PANKF+IMpQVDflj1w
9UMixoPRFdlOoMXVmC7yT0sfE1B6REJIh0Qfa4pqDwnHRhs8imgoIYA+JwFnmFPr
k5Q8xS2YCwopH/7W5aRLzyEI2dF6Rfy9FID8jfyNoKZLtBW6cIEkA4zTv41BZSuj
4Zj2etELXAnkIWMZXXdeKSz8IoSOlgjsCR482QmzTRuoFdmVLoJgsgh9hO2+oK07
vJDEVJnXKxq1pF6DVbYwuzNgPB1pRzg6Y8EitdH3SBgjsOQ/m4RpKaqN0MkQhYrB
BI9PCiF7GKCzNfNl3b/Op+HSsZ6aJkOsQPzC89/Ww0mB8azypgAwvLsjte5R3hib
fS8z+V+lxAAC0/M981TsPKJ96HNv4VXbLI3bY9qJBd2LB+NDortsF/OkUuObsh+6
hVQCWnae5V5iq8WmMTFABfBAK5lHafop87edn6X33LOyZZQCT9svNz/zrpakXh0e
/SBGTUudtjCOy/BLj1VQrb6tczEzos7Ij+bszeIBAcSzrWg8gtVPjw9TvuAo2b/b
9nwR4yrm0Q==
=db/l
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
* tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (106 commits)
MAINTAINERS: drop an old reference to stm32 pwm timers doc
MAINTAINERS: dt: update etnaviv file reference
dt-bindings: usb: dwc2: fix bindings for amlogic, meson-gxbb-usb
dt-bindings: uniphier-system-bus: fix warning in the example
dt-bindings: display: meson-vpu: fix indentation of reg-names' "items"
dt-bindings: iio: Fix adi, ltc2983 uint64-matrix schema constraints
dt-bindings: power: Fix example for power-domain
dt-bindings: arm: Add some constraints for PSCI nodes
of: some unittest overlays not untracked
of: gpio unittest kfree() wrong object
dt-bindings: phy: convert phy-rockchip-inno-usb2 bindings to yaml
dt-bindings: serial: sh-sci: Convert to json-schema
dt-bindings: serial: Document serialN aliases
dt-bindings: thermal: tsens: Set 'additionalProperties: false'
dt-bindings: thermal: tsens: Fix nvmem-cell-names schema
dt-bindings: vendor-prefixes: Add Beacon vendor prefix
dt-bindings: vendor-prefixes: Add Topwise
of: of_private.h: Replace zero-length array with flexible-array member
docs: dt: fix a broken reference to input.yaml
docs: dt: fix references to ap806-system-controller.txt
...
Convert the Renesas Serial Communication Interface ((H)SCI(F)(A|B))
Device Tree binding documentation to json-schema.
Split the bindings in 5 files, one per major type, to ease expressing
constraints.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Document the format of aliases referring to UARTs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Setting 'additionalProperties: false' is frequently omitted, but is
important in order to check that there aren't extra undocumented
properties in a binding.
Ideally, we'd just add this automatically and make this the default, but
there's some cases where it doesn't work. For example, if a common
schema is referenced, then properties in the common schema aren't part
of what's considered for 'additionalProperties'. Also, sometimes there
are bus specific properties such as 'spi-max-frequency' that go into
bus child nodes, but aren't defined in the child node's schema.
So let's stick with the json-schema defined default and add
'additionalProperties: false' where needed. This will be a continual
review comment and game of wack-a-mole.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Stephen Boyd <sboyd@kernel.org> # clock
Acked-by: Lee Jones <lee.jones@linaro.org>
Convert the serial slave-device Device Tree binding documentation to
json-schema, and incorporate it into the generic serial bindings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the generic serial interface Device Tree binding documentation
to json-schema.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
A test with the command below gives these errors:
arch/arm64/boot/dts/rockchip/rk3308-evb.dt.yaml: serial@ff0d0000: compatible:
['rockchip,rk3308-uart', 'snps,dw-apb-uart']
is not valid under any of the given schemas
arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dt.yaml: serial@ff0a0000: compatible:
['rockchip,rk3308-uart', 'snps,dw-apb-uart']
is not valid under any of the given schemas
The compatible property for the Rockchip rk3308 uart was somehow never
added to the documention. Fix this error by adding 'rockchip,rk3308-uart'
to snps-dw-apb-uart.yaml.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/serial/
snps-dw-apb-uart.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a description for the new fsl,inverted-tx and fsl,inverted-rx
options for the i.MX UART peripheral.
Signed-off-by: George Hilliard <ghilliard@kopismobile.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200226222319.18383-2-ghilliard@kopismobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" tty and serial driver patches for 5.5-rc1. It's a bit
later in the merge window than normal as I wanted to make sure some
last-minute patches applied to it were all sane. They seem to be :)
There's a lot of little stuff in here, for the tty core, and for lots of
serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXebFIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylnmACgjfMcfQWa7uC9Q6m2DaQaRMaW6QoAnjg+TgBB
eW9EhvyXL2VbrsuUl+iH
=Am9O
-----END PGP SIGNATURE-----
Merge tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404 interconnect,
Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
-----BEGIN PGP SIGNATURE-----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=L6uq
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404
interconnect, Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
* tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (138 commits)
libfdt: define INT32_MAX and UINT32_MAX in libfdt_env.h
dt-bindings: arm: Remove leftover axentia.txt
of: unittest: fix memory leak in attach_node_and_children
of: overlay: add_changeset_property() memory leak
dt-bindings: interrupt-controller: arm,gic-v3: Add missing type to interrupt-partition-* nodes
dt-bindings: firmware: ixp4xx: Drop redundant minItems/maxItems
dt-bindings: power: Rename back power_domain.txt bindings to fix references
dt-bindings: i2c: stm32: Migrate i2c-stm32 documentation to yaml
dt-bindings: mtd: Convert stm32 fmc2-nand bindings to json-schema
dt-bindings: remoteproc: convert stm32-rproc to json-schema
dt-bindings: mailbox: convert stm32-ipcc to json-schema
dt-bindings: mfd: Convert stm32 low power timers bindings to json-schema
dt-bindings: interrupt-controller: Convert stm32-exti to json-schema
dt-bindings: crypto: Convert stm32 HASH bindings to json-schema
dt-bindings: rng: Convert stm32 RNG bindings to json-schema
dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
dt-bindings: pwm: Convert PWM bindings to json-schema
dt-bindings: serial: Add a new compatible string for SC9863A
dt-bindings: serial: Convert sprd-uart to json-schema
dt-bindings: arm: Add bindings for Unisoc SC9863A
...
SC9863A use the same serial device which SC9836 uses.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert Samsung S3C/S5P/Exynos Serial/UART bindings to DT schema format
using json-schema.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Document support for the SCIF and HSCIF serial ports in the Renesas
R-Car M3-W+ (R8A77961) SoC.
Update all references to R-Car M3-W from "r8a7796" to "r8a77960", to
avoid confusion between R-Car M3-W (R8A77960) and M3-W+.
No driver update is needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191023123010.12501-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add documentation for 8250_aspeed_vuart's aspeed,sirq-polarity-sense
property that enables to auto-configure the VUART's SIRQ polarity.
Signed-off-by: Oskar Senft <osk@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190905144130.220713-2-osk@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RZ/G2N (R8A774B1) SoC also has the R-Car Gen3 compatible SCIF and
HSCIF ports, so document the SoC specific bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1568724324-26995-1-git-send-email-biju.das@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- A bunch of DT binding conversions to DT schema format
- Clean-ups of the Arm idle-states binding
- Support a default number of cells in of_for_each_phandle() when the
cells name is missing
- Expose dtbs_check and dt_binding_check in the make help
- Convert writting-schema.md to ReST
- HiSilicon reset controller binding updates
- Add documentation for MT8516 RNG
-----BEGIN PGP SIGNATURE-----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=ZO6c
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- a bunch of DT binding conversions to DT schema format
- clean-ups of the Arm idle-states binding
- support a default number of cells in of_for_each_phandle() when the
cells name is missing
- expose dtbs_check and dt_binding_check in the make help
- convert writting-schema.md to ReST
- HiSilicon reset controller binding updates
- add documentation for MT8516 RNG
* tag 'devicetree-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (46 commits)
of: restore old handling of cells_name=NULL in of_*_phandle_with_args()
bus: qcom: fix spelling mistake "ambigous" -> "ambiguous"
of: Let of_for_each_phandle fallback to non-negative cell_count
iommu: pass cell_count = -1 to of_for_each_phandle with cells_name
dt-bindings: arm: Convert Realtek board/soc bindings to json-schema
dt-bindings: arm: Convert Actions Semi bindings to jsonschema
dt-bindings: Correct spelling in example schema
dt-bindings: cpu: Add a support cpu type for cortex-a55
dt-bindings: gpu: mali-midgard: Add samsung exynos5250 compatible
dt-bindings: arm: idle-states: Move exit-latency-us explanation
dt-bindings: arm: idle-states: Add punctuation to improve readability
dt-bindings: arm: idle-states: Correct "constraint guarantees"
dt-bindings: arm: idle-states: Correct references to wake-up delay
dt-bindings: arm: idle-states: Use "e.g." and "i.e." consistently
pinctrl-mcp23s08: Fix property-name in dt-example
dt-bindings: Clarify interrupts-extended usage
dt-bindings: Convert Arm Mali Utgard GPU to DT schema
dt-bindings: Convert Arm Mali Bifrost GPU to DT schema
dt-bindings: Convert Arm Mali Midgard GPU to DT schema
dt-bindings: irq: Convert Allwinner NMI Controller to a schema
...
Even in this age, people are still making new serial port silicon,
why...
Anyway, here's the TTY and Serial driver update for 5.4-rc1. Lots of
changes in here for a number of embedded serial port devices that are
being worked on because people really like to see those console logs...
Other than that, nothing major here, no core tty changes that anyone
should care about.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIXfw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymmNACeIYq7038NXGBXBj1DfN90GeGNenwAnRkjzF+6
YwEhFRxOMglnbvDevgPU
=E6jv
-----END PGP SIGNATURE-----
Merge tag 'tty-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Even in this age, people are still making new serial port silicon,
why...
Anyway, here's the TTY and Serial driver update for 5.4-rc1. Lots of
changes in here for a number of embedded serial port devices that are
being worked on because people really like to see those console
logs...
Other than that, nothing major here, no core tty changes that anyone
should care about.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (125 commits)
serial: tegra: Add PIO mode support
serial: tegra: report clk rate errors
serial: tegra: add support to adjust baud rate
serial: tegra: DT for Adjusted baud rates
serial: tegra: add support to use 8 bytes trigger
serial: tegra: set maximum num of uart ports to 8
serial: tegra: check for FIFO mode enabled status
dt-binding: serial: tegra: add new chips
serial: tegra: report error to upper tty layer
serial: tegra: flush the RX fifo on frame error
serial: tegra: avoid reg access when clk disabled
serial: tegra: add support to ignore read
serial: sprd: correct the wrong sequence of arguments
dt-bindings: serial: Convert riscv,sifive-serial to json-schema
serial: max310x: turn off transmitter before activating AutoCTS or auto transmitter flow control
serial: max310x: Properly set flags in AutoCTS mode
tty: serial: fix platform_no_drv_owner.cocci warnings
dt-bindings: serial: Document Freescale LINFlexD UART
serial: fsl_linflexuart: Update compatible string
tty: n_gsm: avoid recursive locking with async port hangup
...
Tegra186 chip has a hardware issue resulting in frame errors when
tolerance level for baud rate is negative. Provided entries to adjust
baud rate to be within acceptable range and work with devices that
can send negative baud rate. Also report error when baud rate set is
out of tolerance range of controller updated in device tree.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-10-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new compatible string for Tegra186. It differs from earlier chips
as it has FIFO mode enable check and 8 byte DMA buffer.
Add new compatible string for Tegra194. Tegra194 has different error
tolerance levels for baud rate compared to older chips.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-6-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add documentation for the serial communication interface module (LINFlexD),
found in two instances on S32V234.
Signed-off-by: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Larisa Grigore <Larisa.Grigore@nxp.com>
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190823191115.18490-7-stefan-gabriel.mirea@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a note for enabling wakeup capabilities of usart
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1560433800-12255-2-git-send-email-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rob Herring