Book3S PACA memory allocation is restricted by the RMA limit and also
must not take SLB faults when accessed in virtual mode. Currently a
fixed 256MB limit is used for this, which is imprecise and sub-optimal.
Update the paca allocation limits to use use the ppc64_rma_size for RMA
limit, and share the safe_stack_limit() that is currently used for stack
allocations that must not take virtual mode faults.
The safe_stack_limit() name is changed to ppc64_bolted_size() to match
ppc64_rma_size and some comments are updated. We also need to use
early_mmu_has_feature() because we are now calling this function prior
to the jump label patching that enables mmu_has_feature().
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Change mmu_has_feature() to early_mmu_has_feature()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This statement causes some not very useful messages to always
be printed on the serial port at boot, even on quiet boots.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Take the DSCR value set by firmware as the dscr_default value,
rather than zero.
POWER9 recommends DSCR default to a non-zero value.
Signed-off-by: From: Nicholas Piggin <npiggin@gmail.com>
[mpe: Make record_spr_defaults() __init]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OPAL boot does not insert secondaries at 0x60 to wait at the secondary
hold spinloop. Instead they are started later, and inserted at
generic_secondary_smp_init(), which is after the secondary hold
spinloop.
Avoid waiting on this spinloop when booting with OPAL firmware. This
wait always times out that case.
This saves 100ms boot time on powernv, and 10s of seconds of real time
when booting on the simulator in SMP.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes a couple more bits of fallout from the new hard lockup watchdog
patch.
It restores the required hw_nmi_get_sample_period() function for the
perf watchdog, and removes some function declarations on 64e that are only
defined for 64s. This fixes the 64e build when the hardlockup detector is
enabled.
It restores the default behaviour of disabling the perf watchdog, and also
fixes disabling the 64s watchdog when running as a guest.
Fixes: 2104180a53 ("powerpc/64s: implement arch-specific hardlockup watchdog")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Radix MMU does not take SLB or TLB interrupts when accessing kernel
linear address. Remove this restriction for radix mode.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implement an arch-speicfic watchdog rather than use the perf-based
hardlockup detector.
The new watchdog takes the soft-NMI directly, rather than going through
perf. Perf interrupts are to be made maskable in future, so that would
prevent the perf detector from working in those regions.
Additionally, implement a SMP based detector where all CPUs watch one
another by pinging a shared cpumask. This is because powerpc Book3S
does not have a true periodic local NMI, but some platforms do implement
a true NMI IPI.
If a CPU is stuck with interrupts hard disabled, the soft-NMI watchdog
does not work, but the SMP watchdog will. Even on platforms without a
true NMI IPI to get a good trace from the stuck CPU, other CPUs will
notice the lockup sufficiently to report it and panic.
[npiggin@gmail.com: honor watchdog disable at boot/hotplug]
Link: http://lkml.kernel.org/r/20170621001346.5bb337c9@roar.ozlabs.ibm.com
[npiggin@gmail.com: fix false positive warning at CPU unplug]
Link: http://lkml.kernel.org/r/20170630080740.20766-1-npiggin@gmail.com
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20170616065715.18390-6-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Tested-by: Babu Moger <babu.moger@oracle.com> [sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split SOFTLOCKUP_DETECTOR from LOCKUP_DETECTOR, and split
HARDLOCKUP_DETECTOR_PERF from HARDLOCKUP_DETECTOR.
LOCKUP_DETECTOR implies the general boot, sysctl, and programming
interfaces for the lockup detectors.
An architecture that wants to use a hard lockup detector must define
HAVE_HARDLOCKUP_DETECTOR_PERF or HAVE_HARDLOCKUP_DETECTOR_ARCH.
Alternatively an arch can define HAVE_NMI_WATCHDOG, which provides the
minimum arch_touch_nmi_watchdog, and it otherwise does its own thing and
does not implement the LOCKUP_DETECTOR interfaces.
sparc is unusual in that it has started to implement some of the
interfaces, but not fully yet. It should probably be converted to a full
HAVE_HARDLOCKUP_DETECTOR_ARCH.
[npiggin@gmail.com: fix]
Link: http://lkml.kernel.org/r/20170617223522.66c0ad88@roar.ozlabs.ibm.com
Link: http://lkml.kernel.org/r/20170616065715.18390-4-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Babu Moger <babu.moger@oracle.com>
Tested-by: Babu Moger <babu.moger@oracle.com> [sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Emergency stacks have their thread_info mostly uninitialised, which in
particular means garbage preempt_count values.
Emergency stack code runs with interrupts disabled entirely, and is
used very rarely, so this has been unnoticed so far. It was found by a
proposed new powerpc watchdog that takes a soft-NMI directly from the
masked_interrupt handler and using the emergency stack. That crashed
at BUG_ON(in_nmi()) in nmi_enter(). preempt_count()s were found to be
garbage.
To fix this, zero the entire THREAD_SIZE allocation, and initialize
the thread_info.
Cc: stable@vger.kernel.org
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Move it all into setup_64.c, use a function not a macro. Fix
crashes on Cell by setting preempt_count to 0 not HARDIRQ_OFFSET]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 8c27226119 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"), we
switched to the generic implementation of cpu_to_node(), which uses a percpu
variable to hold the NUMA node for each CPU.
Unfortunately we neglected to notice that we use cpu_to_node() in the allocation
of our percpu areas, leading to a chicken and egg problem. In practice what
happens is when we are setting up the percpu areas, cpu_to_node() reports that
all CPUs are on node 0, so we allocate all percpu areas on node 0.
This is visible in the dmesg output, as all pcpu allocs being in group 0:
pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07
pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15
pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23
pcpu-alloc: [0] 24 25 26 27 [0] 28 29 30 31
pcpu-alloc: [0] 32 33 34 35 [0] 36 37 38 39
pcpu-alloc: [0] 40 41 42 43 [0] 44 45 46 47
To fix it we need an early_cpu_to_node() which can run prior to percpu being
setup. We already have the numa_cpu_lookup_table we can use, so just plumb it
in. With the patch dmesg output shows two groups, 0 and 1:
pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07
pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15
pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23
pcpu-alloc: [1] 24 25 26 27 [1] 28 29 30 31
pcpu-alloc: [1] 32 33 34 35 [1] 36 37 38 39
pcpu-alloc: [1] 40 41 42 43 [1] 44 45 46 47
We can also check the data_offset in the paca of various CPUs, with the fix we
see:
CPU 0: data_offset = 0x0ffe8b0000
CPU 24: data_offset = 0x1ffe5b0000
And we can see from dmesg that CPU 24 has an allocation on node 1:
node 0: [mem 0x0000000000000000-0x0000000fffffffff]
node 1: [mem 0x0000001000000000-0x0000001fffffffff]
Cc: stable@vger.kernel.org # v3.16+
Fixes: 8c27226119 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights include:
- rework the Linux page table geometry to lower memory usage on 64-bit Book3S
(IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features on future
firmwares.
- Freescale updates from Scott: "Includes a fix for a powerpc/next mm regression
on 64e, a fix for a kernel hang on 64e when using a debugger inside a
relocated kernel, a qman fix, and misc qe improvements."
Thanks to:
Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong, Nicholas Piggin, Roy
Pledge, Scott Wood, Valentin Longchamp.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZFXjPAAoJEFHr6jzI4aWAgG4QAJoF7G5Txj0Du2I2/wQDkVq1
InJ+BNji0xnOrFpz2EcIIlbIwBeJbY9cSIbmKUEPQU4hxtQgI8Q5WNEl2btWq8xz
I0Ej3uc5obc9ltUdQoGxgXih/XDd8UN3fscSE2/SSuPY/A7JwAVZMsCEJ1tWdxpM
hx+R9wlaUT3I6jmQwj9gg6zuBdIOL5szvZXKh9ruPKNyZWbPmPSUwIqiyT0YHsiD
01OZsFYpdSH6Ka/eNHSNx5HC+kK8aDVaqd5E2fkHeH9+sxerpEzMo2PmK4T8vChh
mSD4nhfqRwC2WRpPF/MY+zGBeXrFkCkR+nYhaqVDXXACKzfHgU58NOfvrmtRj52X
vTW+cn92wqFTmi0TNUfhEFt8elcOO7/fKh1OVhsFx+bD+bgj8G1ZkLoBU/0QUzRf
R4hiKKuOMnDHriNPdlAOKjHpR+ewh8Q679INThEJzEQpn7VBY72hcQwapQ3MjMnd
E7LfsGwqGPkTc6gy1bFbWum5HMGOcmE0qkrnZo5VyFhNNwBs1Kx/B1GHjUOiucVu
km5GEVNTfCkZqeabdca7fwbGcMH7zchR1ootqH2m18PZJAzr85A+aTqfrdJ5fDBs
v/nznfcPVNEgvEW0im2jhpPoAlQE6/YvYa+kG4zjjxWA5FKVKdTzINexD82jlcqP
+fDtIDxNcFkzlt4gacjh
=YOQs
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"The change to the Linux page table geometry was delayed for more
testing with 16G pages, and there's the new CPU features stuff which
just needed one more polish before going in. Plus a few changes from
Scott which came in a bit late. And then various fixes, mostly minor.
Summary highlights:
- rework the Linux page table geometry to lower memory usage on
64-bit Book3S (IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features
on future firmwares.
- Freescale updates from Scott:
"Includes a fix for a powerpc/next mm regression on 64e, a fix for
a kernel hang on 64e when using a debugger inside a relocated
kernel, a qman fix, and misc qe improvements."
Thanks to: Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong,
Nicholas Piggin, Roy Pledge, Scott Wood, Valentin Longchamp"
* tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Support new device tree binding for discovering CPU features
powerpc: Don't print cpu_spec->cpu_name if it's NULL
of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
powerpc/64s: Fix unnecessary machine check handler relocation branch
powerpc/mm/book3s/64: Rework page table geometry for lower memory usage
powerpc: Fix distclean with Makefile.postlink
powerpc/64e: Don't place the stack beyond TASK_SIZE
powerpc/powernv: Block PCI config access on BCM5718 during EEH recovery
powerpc/8xx: Adding support of IRQ in MPC8xx GPIO
soc/fsl/qbman: Disable IRQs for deferred QBMan work
soc/fsl/qe: add EXPORT_SYMBOL for the 2 qe_tdm functions
soc/fsl/qe: only apply QE_General4 workaround on affected SoCs
soc/fsl/qe: round brg_freq to 1kHz granularity
soc/fsl/qe: get rid of immrbar_virt_to_phys()
net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
powerpc/64e: Fix hang when debugging programs with relocated kernel
The ibm,powerpc-cpu-features device tree binding describes CPU features with
ASCII names and extensible compatibility, privilege, and enablement metadata
that allows improved flexibility and compatibility with new hardware.
The interface is described in detail in ibm,powerpc-cpu-features.txt in this
patch.
Currently this code is not enabled by default, and there are no released
firmwares that provide the binding.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights include:
- Larger virtual address space on 64-bit server CPUs. By default we use a 128TB
virtual address space, but a process can request access to the full 512TB by
passing a hint to mmap().
- Support for the new Power9 "XIVE" interrupt controller.
- TLB flushing optimisations for the radix MMU on Power9.
- Support for CAPI cards on Power9, using the "Coherent Accelerator Interface
Architecture 2.0".
- The ability to configure the mmap randomisation limits at build and runtime.
- Several small fixes and cleanups to the kprobes code, as well as support for
KPROBES_ON_FTRACE.
- Major improvements to handling of system reset interrupts, correctly treating
them as NMIs, giving them a dedicated stack and using a new hypervisor call
to trigger them, all of which should aid debugging and robustness.
Many fixes and other minor enhancements.
Thanks to:
Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anshuman Khandual, Anton Blanchard, Balbir Singh, Ben
Hutchings, Benjamin Herrenschmidt, Bhupesh Sharma, Chris Packham, Christian
Zigotzky, Christophe Leroy, Christophe Lombard, Daniel Axtens, David Gibson,
Gautham R. Shenoy, Gavin Shan, Geert Uytterhoeven, Guilherme G. Piccoli,
Hamish Martin, Hari Bathini, Kees Cook, Laurent Dufour, Madhavan Srinivasan,
Mahesh J Salgaonkar, Mahesh Salgaonkar, Masami Hiramatsu, Matt Brown, Matthew
R. Ochs, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran,
Pan Xinhui, Paul Mackerras, Rashmica Gupta, Russell Currey, Sukadev
Bhattiprolu, Thadeu Lima de Souza Cascardo, Tobin C. Harding, Tyrel Datwyler,
Uma Krishnan, Vaibhav Jain, Vipin K Parashar, Yang Shi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vSF3
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Larger virtual address space on 64-bit server CPUs. By default we
use a 128TB virtual address space, but a process can request access
to the full 512TB by passing a hint to mmap().
- Support for the new Power9 "XIVE" interrupt controller.
- TLB flushing optimisations for the radix MMU on Power9.
- Support for CAPI cards on Power9, using the "Coherent Accelerator
Interface Architecture 2.0".
- The ability to configure the mmap randomisation limits at build and
runtime.
- Several small fixes and cleanups to the kprobes code, as well as
support for KPROBES_ON_FTRACE.
- Major improvements to handling of system reset interrupts,
correctly treating them as NMIs, giving them a dedicated stack and
using a new hypervisor call to trigger them, all of which should
aid debugging and robustness.
- Many fixes and other minor enhancements.
Thanks to: Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple,
Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual, Anton
Blanchard, Balbir Singh, Ben Hutchings, Benjamin Herrenschmidt,
Bhupesh Sharma, Chris Packham, Christian Zigotzky, Christophe Leroy,
Christophe Lombard, Daniel Axtens, David Gibson, Gautham R. Shenoy,
Gavin Shan, Geert Uytterhoeven, Guilherme G. Piccoli, Hamish Martin,
Hari Bathini, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Mahesh J
Salgaonkar, Mahesh Salgaonkar, Masami Hiramatsu, Matt Brown, Matthew
R. Ochs, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Oliver
O'Halloran, Pan Xinhui, Paul Mackerras, Rashmica Gupta, Russell
Currey, Sukadev Bhattiprolu, Thadeu Lima de Souza Cascardo, Tobin C.
Harding, Tyrel Datwyler, Uma Krishnan, Vaibhav Jain, Vipin K Parashar,
Yang Shi"
* tag 'powerpc-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (214 commits)
powerpc/64s: Power9 has no LPCR[VRMASD] field so don't set it
powerpc/powernv: Fix TCE kill on NVLink2
powerpc/mm/radix: Drop support for CPUs without lockless tlbie
powerpc/book3s/mce: Move add_taint() later in virtual mode
powerpc/sysfs: Move #ifdef CONFIG_HOTPLUG_CPU out of the function body
powerpc/smp: Document irq enable/disable after migrating IRQs
powerpc/mpc52xx: Don't select user-visible RTAS_PROC
powerpc/powernv: Document cxl dependency on special case in pnv_eeh_reset()
powerpc/eeh: Clean up and document event handling functions
powerpc/eeh: Avoid use after free in eeh_handle_special_event()
cxl: Mask slice error interrupts after first occurrence
cxl: Route eeh events to all drivers in cxl_pci_error_detected()
cxl: Force context lock during EEH flow
powerpc/64: Allow CONFIG_RELOCATABLE if COMPILE_TEST
powerpc/xmon: Teach xmon oops about radix vectors
powerpc/mm/hash: Fix off-by-one in comment about kernel contexts ids
powerpc/pseries: Enable VFIO
powerpc/powernv: Fix iommu table size calculation hook for small tables
powerpc/powernv: Check kzalloc() return value in pnv_pci_table_alloc
powerpc: Add arch/powerpc/tools directory
...
The system reset interrupt is used for crash/debug situations, so it is
desirable to have as little impact on the normal state of the system as
possible.
Currently it uses the current kernel stack to process the exception.
This stores into the stack which may be involved with the crash. The
stack pointer may be corrupted, or it may have overflowed.
Avoid or minimise these problems by creating a dedicated NMI stack for
the system reset interrupt to use.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On Power8 & Power9 the early CPU inititialisation in __init_HFSCR()
turns on HFSCR[TM] (Hypervisor Facility Status and Control Register
[Transactional Memory]), but that doesn't take into account that TM
might be disabled by CPU features, or disabled by the kernel being built
with CONFIG_PPC_TRANSACTIONAL_MEM=n.
So later in boot, when we have setup the CPU features, clear HSCR[TM] if
the TM CPU feature has been disabled. We use CPU_FTR_TM_COMP to account
for the CONFIG_PPC_TRANSACTIONAL_MEM=n case.
Without this a KVM guest might try use TM, even if told not to, and
cause an oops in the host kernel. Typically the oops is seen in
__kvmppc_vcore_entry() and may or may not be fatal to the host, but is
always bad news.
In practice all shipping CPU revisions do support TM, and all host
kernels we are aware of build with TM support enabled, so no one should
actually be able to hit this in the wild.
Fixes: 2a3563b023 ("powerpc: Setup in HFSCR for POWER8")
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
[mpe: Rewrite change log with input from Sam, add Fixes/stable]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cpu_ready_for_interrupts() is called after feature patching, so there's
no need to use early_cpu_has_feature().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
I see a panic in early boot when building with a recent gcc toolchain.
The issue is a divide by zero, which is undefined. Older toolchains
let us get away with it:
int foo(int a) { return a / 0; }
foo:
li 9,0
divw 3,3,9
extsw 3,3
blr
But newer ones catch it:
foo:
trap
Add a check to avoid the divide by zero.
Fixes: e2827fe5c1 ("powerpc/64: Clean up ppc64_caches using a struct per cache")
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
WARN_ONCE() takes a condition and a format string. We were passing a
constant string as the condition, and the function name as the format
string. It would work, but the message would be just the function name.
Fix it by just using WARN_ONCE() directly instead of if (x) WARN_ONCE().
Noticed-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds AUX vectors for the L1I,D, L2 and L3 cache levels
providing for each cache level the size of the cache in bytes
and the geometry (line size and number of ways).
We chose to not use the existing alpha/sh definition which
packs all the information in a single entry per cache level as
it is too restricted to represent some of the geometries used
on POWER.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All shipping firmware versions have it wrong in the device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Retrieved from device-tree when available
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have two set of identical struct members for the I and D sides
and mostly identical bunches of code to parse the device-tree to
populate them. Instead make a ppc_cache_info structure with one
copy for I and one for D
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It will be used to calculate the associativity
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In a number of places we called "cache line size" what is actually
the cache block size, which in the powerpc architecture, means the
effective size to use with cache management instructions (it can
be different from the actual cache line size).
We fix the naming across the board and properly retrieve both
pieces of information when available in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We don't patch instructions based on the cache lines or block
sizes these days.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The variables are defined twice in setup_32.c and setup_64.c, do it
once in setup-common.c instead
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for secure and
trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and store
them as relative offsets to save space in the kernel image & memory.
- Allow building the kernel with thin archives, which should allow us to build
an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the kernel endian
from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9 Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage support,
qbman fixes/cleanup, device tree updates, and some misc cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual,
Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz, Christophe Jaillet,
Christophe Leroy, Denis Kirjanov, Elimar Riesebieter, Frederic Barrat,
Gautham R. Shenoy, Geliang Tang, Geoff Levand, Jack Miller, Johan Hovold,
Lars-Peter Clausen, Libin, Madhavan Srinivasan, Michael Neuling, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin,
Rashmica Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xOzf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for
secure and trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to
SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and
store them as relative offsets to save space in the kernel image &
memory.
- Allow building the kernel with thin archives, which should allow us
to build an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the
kernel endian from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9
Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via
debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage
support, qbman fixes/cleanup, device tree updates, and some misc
cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman
Khandual, Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz,
Christophe Jaillet, Christophe Leroy, Denis Kirjanov, Elimar
Riesebieter, Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff
Levand, Jack Miller, Johan Hovold, Lars-Peter Clausen, Libin,
Madhavan Srinivasan, Michael Neuling, Nathan Fontenot, Naveen N.
Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin, Rashmica
Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain"
[ And thanks to Michael, who took time off from a new baby to get this
pull request done. - Linus ]
* tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (174 commits)
powerpc/fsl/dts: add FMan node for t1042d4rdb
powerpc/fsl/dts: add sg_2500_aqr105_phy4 alias on t1024rdb
powerpc/fsl/dts: add QMan and BMan nodes on t1024
powerpc/fsl/dts: add QMan and BMan nodes on t1023
soc/fsl/qman: test: use DEFINE_SPINLOCK()
powerpc/fsl-lbc: use DEFINE_SPINLOCK()
powerpc/8xx: Implement support of hugepages
powerpc: get hugetlbpage handling more generic
powerpc: port 64 bits pgtable_cache to 32 bits
powerpc/boot: Request no dynamic linker for boot wrapper
soc/fsl/bman: Use resource_size instead of computation
soc/fsl/qe: use builtin_platform_driver
powerpc/fsl_pmc: use builtin_platform_driver
powerpc/83xx/suspend: use builtin_platform_driver
powerpc/ftrace: Fix the comments for ftrace_modify_code
powerpc/perf: macros for power9 format encoding
powerpc/perf: power9 raw event format encoding
powerpc/perf: update attribute_group data structure
powerpc/perf: factor out the event format field
powerpc/mm/iommu, vfio/spapr: Put pages on VFIO container shutdown
...
Commit 2965faa5e0 ("kexec: split kexec_load syscall from kexec core
code") introduced CONFIG_KEXEC_CORE so that CONFIG_KEXEC means whether
the kexec_load system call should be compiled-in and CONFIG_KEXEC_FILE
means whether the kexec_file_load system call should be compiled-in.
These options can be set independently from each other.
Since until now powerpc only supported kexec_load, CONFIG_KEXEC and
CONFIG_KEXEC_CORE were synonyms. That is not the case anymore, so we
need to make a distinction. Almost all places where CONFIG_KEXEC was
being used should be using CONFIG_KEXEC_CORE instead, since
kexec_file_load also needs that code compiled in.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit d3cbff1b5 "powerpc: Put exception configuration in a common place"
broke the setting of the AIL bit (which enables taking exceptions with
the MMU still on) on all processors, moving it incorrectly to a function
called only on the boot CPU. This was correct for the guest case but
not when running in hypervisor mode.
This fixes it by partially reverting that commit, putting the setting
back in cpu_ready_for_interrupts()
Fixes: d3cbff1b5a ("powerpc: Put exception configuration in a common place")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We cannot do those initializations from apply_feature_fixups() as
this function runs in a very restricted environment on 32-bit where
the kernel isn't running at its linked address and the PTRRELOC()
macro must be used for any global accesss.
Instead, split them into a separtate steup_feature_keys() function
which is called in a more suitable spot on ppc32.
Fixes: 309b315b6e ("powerpc: Call jump_label_init() in apply_feature_fixups()")
Reported-and-tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This switches early feature checks to use the non static key variant of
the function. In later patches we will be switching cpu_has_feature()
and mmu_has_feature() to use static keys and we can use them only after
static key/jump label is initialized. Any check for feature before jump
label init should be done using this new helper.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Up until now we needed to do the MMU init before feature patching,
because part of the MMU init was scanning the device tree and setting
and/or clearing some MMU feature bits.
Now that we have split that MMU feature modification out into routines
called from early_init_devtree() (called earlier) we can now do feature
patching before calling MMU init.
The advantage of this is it means the remainder of the MMU init runs
with the final set of features which will apply for the rest of the life
of the system. This means we don't have to special case anything called
from MMU init to deal with a changing set of feature bits.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is little enough differences now.
mpe: Add a/p/k/setup.h to contain the prototypes and empty versions of
functions we need, rather than using weak functions. Add a few other
empty versions to avoid as many #ifdefs as possible in the code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Do it right after probe_machine() since it's about testing ppc_md,
and put the test in the common code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It makes more sense to do it before intializing xmon() as xmon might
use the info in there. We do want to register the console early
though in case we want some functioning printk's in the cpu map setup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Also remove the completely osbolete comment. We *do* look in the
device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is now called right after platform probe, so the probe function
can just do the job.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We no long need the machine type that early, so we can move probe_machine()
to after the device-tree has been expanded. This will allow further
consolidation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The various calls to establish exception endianness and AIL are
now done from a single point using already established CPU and FW
feature bits to decide what to do.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is really no need to do them that early, early_setup() runs
before MMU is on, we should do the strict minimum there to get the
MMU going.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make it part of early_setup() as we really want the feature fixups
to be applied before we turn on the MMU since they can have an impact
on the various assembly path related to MMU management and interrupts.
This makes 64-bit match what 32-bit does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
32 and 64-bit do a similar set of calls early on, we move it all to
a single common function to make the boot code more readable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function is called by both 32-bit and 64-bit early setup right
after early_init_devtree(). All it does is run yet another early
DT parser which is precisely what early_init_devtree() is about,
so move it in there.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anything in early_setup() needs to be justified to be there, in
this case, we need the trampolines before we can take exceptions
and thus before we turn on the MMU.
Also remove a pretty meaningless and misplaced debug message
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Fix comment formatting]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Current comment in the early_setup_secondary() for paca->soft_enabled
update is misleading. Comment should say to Mark interrupts "disabled"
instead of "enabled". Fix the typo.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to support live patching we need to maintain an alternate
stack of TOC & LR values. We use the base of the stack for this, and
store the "live patch stack pointer" in struct thread_info.
Unlike the other fields of thread_info, we can not statically initialise
that value, so it must be done at run time.
This patch just adds the code to support that, it is not enabled until
the next patch which actually adds live patch support.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Nicholas Piggin