AFAICT the code which checks that the requested pixclock value is within
bounds is incorrect. It ensures that the lcdc core clock is at least
(bytes per pixel) times higher than the pixel clock rather than just
greater than or equal to.
There are tighter restrictions on the pixclock value as a function of bus
width for STN panels but even then it isn't a simple relationship as
currently checked for. IMO either something like the below patch should
be applied or else more detailed checking logic should be implemented
which takes in to account the panel type as well.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Daniel Glockner <dg@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove wrong fifo size definition for some AT91 products.
Due to a misunderstanding of some AT91 datasheets, a fifo size of 2048
(words) has been introduced by mistake. In fact, all products (AT91/AT32)
are sharing the same fifo size of 512 words.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The error test that follows the call to backlight_device_register semms
not to concern the right variable.
A simplified version of the semantic match that finds this problem is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@def0@
expression x;
position p0;
@@
x@p0 = backlight_device_register(...)
@protected@
expression def0.x,E;
position def0.p0;
position p;
statement S;
@@
x@p0
... when != x = E
if (!IS_ERR(x) && ...) {<... x@p ...>} else S
@unprotected@
expression def0.x;
identifier fld;
position def0.p0;
position p != protected.p;
@@
x@p0
... when != x = E
* x@p->fld
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the RGB555 wiring for the atmel LCD.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When suspending the system with atmel_lcdfb enabled, I sometimes see
this:
atmel_lcdfb atmel_lcdfb.0: FIFO underflow 0x10
Which can be explained by the fact that we're not stopping the LCD
controller and its DMA engine when suspending, we're just gating the
clocks to them.
There's another potential issue which may be harder to trigger but
much more nasty: If we gate the clocks at _just_ the right moment,
e.g. when the DMA engine is doing a bus transaction, we may cause the
DMA engine to violate the system bus protocol and cause a lockup.
Avoid these issues by shutting down the LCD controller before entering
suspend (and restarting it when resuming). This prevents the underrun
from happening in the first place, and prevents whatever nastiness is
happening when the bus clock stops in the middle of a DMA transfer.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Specify how much physically continuous, DMA capable memory will be
allocated at driver initialization time. This allow to create framebuffer
device with larger virtual resolution. Combine with y-panning this can be
used to implement double buffering acceleration method.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Panning in the y-direction can be done by simply changing the DMA base
address. This code is already in place, but FBIOPAN_DISPLAY will
currently fail because ypanstep is 0.
Set ypanstep to 1 to indicate that we do support y-panning and also set
the necessary acceleration flags on AT91 (AVR32 already have them.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid division by zero in atmel_lcdfb_check_var() function.
If pixclock is not specified while passing a var structure in
the check_var() funtion, a division by zero occurs (when
translating pixclock to KHz).
This patch adds a checking of this value and try to choose a
video mode in the modelist.
The mode found in the probe function in added to the modelist.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Manage atmel_lcdfb FIFO underflow
Resetting the LCD and DMA allows to fix screen shifting after a FIFO
underflow. It follows reset sequence from errata "LCD Screen Shifting
After a Reset".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix divider calculation and allow CLKVAL = 0 (divisor 2)
It was not possible to get the clock value 0 (divisor 2) because
the test "<=0" force the BYPASS bit to be activated instead.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Per Hedblom <per.hedblom@abem.se>
Cc: Roel Kluin <12o3l@tiscali.nl>
Cc: Jan Weber <jw022609@uni-greifswald.de>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AT91SAM9RL soc has a 2048 bytes deep FIFO, like AT91SAM9263.
[bn@niasdigital.com: fix build breakage in atmel_lcdfb]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds different wiring mode for the LCD screen.
The legacy atmel LCDC IP uses a non standard color mode, "BGR-555.1" instead
"RGB-565". The major part of graphic stacks for embedded systems uses only
"RGB-565". It is possible to swap LCD IOs instead of doing this bit swapping
by software (See application note AT91SAM9 LCD Controller
http://www.atmel.com/dyn/resources/prod_documents/doc6300.pdf)
This wire swapping is done on the at91sam9rl-ek board (board code
using this patch will come later).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Teach atmel_lcdfb driver how to suspend/resume.
Note that the backlight control should probably do more of the same stuff:
turning off display power (more than just the backlight) and stopping the
clocks (and dma to drive the no-longer-seen display). No point in wasting
power to generate images that can't be observed, after all...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the user specified a fixed framebuffer address on the command line, it may
have been initialized already with a splash image or something, so we
shouldn't clear it.
Therefore, we should only initialize the framebuffer if we allocated it
ourselves. This patch also updates the AVR32 setup code to clear the
framebuffer if it allocated it itself, i.e. the user didn't provide a fixed
address or the reservation failed.
I've updated the at91 platform code as well so that it initializes the
framebuffer if it is located in SRAM, but I haven't tested that it actually
works.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from
the LCD controller. It's controlled by "contrast" registers though.
This patch lets boards declare that they have that kind of backlight
control. The driver can then export this control, letting screenblank and
other operations actually take effect ... reducing the typically
substantial power drain from the backlight.
Note that it's not fully cooked
- doesn't force backlight off during system suspend
- the "power" and "blank" events may not be done right
This should be easily added in the future.
[nicolas.ferre@atmel.com: remove unneeded inline and rename functions]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting a display timing parameter too high or too low may cause it to
wrap around and thus become completely wrong. Validate the timings in
atmel_lcdfb_check_var() and saturate to the highest or lowest possible
value if necessary.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for Atmel's AT91CAP9 Customizable Microcontroller family.
<http://www.atmel.com/products/AT91CAP/Default.asp>
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds an additional loop, that delays turning off the DMA
until the LCDC core has been turned off. This prevents the picture
to be shifted some random length when the kernel re-initializes
the LCDC.
Without this patch, the LCDC keeps running for some small time after the
PWRCON:LCD_PWR has been cleared ; the FIFO suffers an underrun and on
re-starting the LCDC the FIFO data stays shifted.
This behavior has been seen and fixed on AT91SAM9261-EK and two custom
AT91SAM9261 boards, all of them having different LCD panels.
Thanks a lot to Anti Sullin for submitting this patch (long
time ago).
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set var->transp.offset and var->transp.length in 32bpp mode to indicate
that the 8 otherwise unused bits can be used for transparency.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes STN LCD support for the atmel_lcdfb framebuffer driver.
This patch is the result of a work from Jan Altenberg and has
been tested on a Hitachi SP06Q002 on at91sam9261ek.
It adds a Kconfig switch that enables the proper LCD in the
board configuration file (STN or TFT). The switch is used
in arch/arm/mach-at91/at91sam9261_devices.c & board-sam9261ek.c
as an example.
This patch includes the "Fix wrong line_length calculation"
little one from Jan and Haavard (submitted earlier).
AT91 platform informations are directly submitted trough
the at91 maintainer, here :
http://article.gmane.org/gmane.linux.kernel/543158
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Cc: "Antonino A. Daplas" <adaplas@gmail.com>
Cc: Jan Altenberg <jan.altenberg@linutronix.de>
Cc: Patrice Vilchez <patrice.vilchez@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds a framebuffer driver to ATMEL AT91SAM9x and AT32 aka AVR32 platforms.
Those chips share quite the same IP and this code is suitable for both
architectures.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Nizette