The dev_attrs field has long been "depreciated" and is finally being
removed, so move the driver to use the "correct" dev_groups field
instead for struct bus_type.
Cc: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
Here is the "big" TTY/Serial patch updates for 4.12-rc1
Not a lot of new things here, the normal number of serial driver updates
and additions, tiny bugs fixed, and some core files split up to make
future changes a bit easier for Nicolas's "tiny-tty" work.
All of these have been in linux-next for a while. There will be a merge
conflict with include/linux/serdev.h coming from the bluetooth tree
merge, which we knew about, as we wanted some of the serdev changes to
go in through that tree. I'll send the expected merge result as a
follow-on message.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWRA9rw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn8OwCXSoCtZMGl25ohu1osCL5G0UEMtgCg2Z9k7hDk
LpQTTN98hHn/VwM47ro=
=X8sk
-----END PGP SIGNATURE-----
Merge tag 'tty-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" TTY/Serial patch updates for 4.12-rc1
Not a lot of new things here, the normal number of serial driver
updates and additions, tiny bugs fixed, and some core files split up
to make future changes a bit easier for Nicolas's "tiny-tty" work.
All of these have been in linux-next for a while"
* tag 'tty-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (62 commits)
serial: small Makefile reordering
tty: split job control support into a file of its own
tty: move baudrate handling code to a file of its own
console: move console_init() out of tty_io.c
serial: 8250_early: Add earlycon support for Palmchip UART
tty: pl011: use "qdf2400_e44" as the earlycon name for QDF2400 E44
vt: make mouse selection of non-ASCII consistent
vt: set mouse selection word-chars to gpm's default
imx-serial: Reduce RX DMA startup latency when opening for reading
serial: omap: suspend device on probe errors
serial: omap: fix runtime-pm handling on unbind
tty: serial: omap: add UPF_BOOT_AUTOCONF flag for DT init
serial: samsung: Remove useless spinlock
serial: samsung: Add missing checks for dma_map_single failure
serial: samsung: Use right device for DMA-mapping calls
serial: imx: setup DCEDTE early and ensure DCD and RI irqs to be off
tty: fix comment typo s/repsonsible/responsible/
tty: amba-pl011: Fix spurious TX interrupts
serial: xuartps: Enable clocks in the pm disable case also
serial: core: Re-use struct uart_port {name} field
...
While examining output from trial builds with -Wformat-security enabled,
many strings were found that should be defined as "const", or as a char
array instead of char pointer. This makes some static analysis easier,
by producing fewer false positives.
As these are all trivial changes, it seemed best to put them all in a
single patch rather than chopping them up per maintainer.
Link: http://lkml.kernel.org/r/20170405214711.GA5711@beast
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jes Sorensen <jes@trained-monkey.org> [runner.c]
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Antonio Quartulli <a@unstable.cc>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kejian Yan <yankejian@huawei.com>
Cc: Daode Huang <huangdaode@hisilicon.com>
Cc: Qianqian Xie <xieqianqian@huawei.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Christian Gromm <christian.gromm@microchip.com>
Cc: Andrey Shvetsov <andrey.shvetsov@k2l.de>
Cc: Jason Litzinger <jlitzingerdev@gmail.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix sparse warnings in drivers/of/.
- Add more overlay unittests.
- Update dtc to v1.4.4-8-g756ffc4f52f6. This adds more checks on dts
files such as unit-address formatting and stricter character sets for
node and property names.
- Add a common DT modalias function.
- Move trivial-devices.txt up and out of i2c dir.
- ARM NVIC interrupt controller binding.
- Vendor prefixes for Sensirion, Dioo, Nordic, ROHM.
- Correct some binding file locations.
-----BEGIN PGP SIGNATURE-----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=ca1M
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- fix sparse warnings in drivers/of/
- add more overlay unittests
- update dtc to v1.4.4-8-g756ffc4f52f6. This adds more checks on dts
files such as unit-address formatting and stricter character sets for
node and property names
- add a common DT modalias function
- move trivial-devices.txt up and out of i2c dir
- ARM NVIC interrupt controller binding
- vendor prefixes for Sensirion, Dioo, Nordic, ROHM
- correct some binding file locations
* tag 'devicetree-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (24 commits)
of: fix sparse warnings in fdt, irq, reserved mem, and resolver code
of: fix sparse warning in of_pci_range_parser_one
of: fix sparse warnings in of_find_next_cache_node
of/unittest: Missing unlocks on error
of: fix uninitialized variable warning for overlay test
of: fix unittest build without CONFIG_OF_OVERLAY
of: Add unit tests for applying overlays
of: per-file dtc compiler flags
fpga: region: add missing DT documentation for config complete timeout
of: Add vendor prefix for ROHM Semiconductor
of: fix "/cpus" reference leak in of_numa_parse_cpu_nodes()
of: Add vendor prefix for Nordic Semiconductor
dt-bindings: arm,nvic: Binding for ARM NVIC interrupt controller on Cortex-M
dtc: update warning settings for new bus and node/property name checks
scripts/dtc: Update to upstream version v1.4.4-8-g756ffc4f52f6
scripts/dtc: automate getting dtc version and log in update script
of: Add function for generating a DT modalias with a newline
of: fix of_device_get_modalias returned length when truncating buffers
Documentation: devicetree: move trivial-devices out of I2C realm
dt-bindings: add vendor prefix for Dioo
..
Tetsuo has reported that sysrq triggered OOM killer will print a
misleading information when no tasks are selected:
sysrq: SysRq : Manual OOM execution
Out of memory: Kill process 4468 ((agetty)) score 0 or sacrifice child
Killed process 4468 ((agetty)) total-vm:43704kB, anon-rss:1760kB, file-rss:0kB, shmem-rss:0kB
sysrq: SysRq : Manual OOM execution
Out of memory: Kill process 4469 (systemd-cgroups) score 0 or sacrifice child
Killed process 4469 (systemd-cgroups) total-vm:10704kB, anon-rss:120kB, file-rss:0kB, shmem-rss:0kB
sysrq: SysRq : Manual OOM execution
sysrq: OOM request ignored because killer is disabled
sysrq: SysRq : Manual OOM execution
sysrq: OOM request ignored because killer is disabled
sysrq: SysRq : Manual OOM execution
sysrq: OOM request ignored because killer is disabled
The real reason is that there are no eligible tasks for the OOM killer
to select but since commit 7c5f64f844 ("mm: oom: deduplicate victim
selection code for memcg and global oom") the semantic of out_of_memory
has changed without updating moom_callback.
This patch updates moom_callback to tell that no task was eligible which
is the case for both oom killer disabled and no eligible tasks. In
order to help distinguish first case from the second add printk to both
oom_killer_{enable,disable}. This information is useful on its own
because it might help debugging potential memory allocation failures.
Fixes: 7c5f64f844 ("mm: oom: deduplicate victim selection code for memcg and global oom")
Link: http://lkml.kernel.org/r/20170404134705.6361-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/tty/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Jiri Slaby <jslaby@suse.com>
cc: linux-serial@vger.kernel.org
Move 21285 entry down alongside other UART drivers to be more consistent
with the rest of the file. It is kept before 8250 though, to preserve the
existing link ordering between those two.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes it easier for job control to become optional and/or usable
independently from tty_io.c, as well as providing a nice purpose
separation. No logical changes from this patch.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow reuse without the rest of the tty_ioctl code.
No logical changes from this patch.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the console driver handling code lives in printk.c.
Move console_init() there as well so console support can still be used
when the TTY code is configured out. No logical changes from this patch.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define an OF early console for Palmchip UART, which can be enabled
by passing "earlycon" on the boot command line.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define a new early console name for Qualcomm Datacenter Technologies
QDF2400 SOCs affected by erratum 44, instead of piggy-backing on "pl011".
Previously, to enable traditional (non-SPCR) earlycon, the documentation
said to specify "earlycon=pl011,<address>,qdf2400_e44", but the code was
broken and this didn't actually work.
So instead, the method for specifying the E44 work-around with traditional
earlycon is "earlycon=qdf2400_e44,<address>". Both methods of earlycon
are now enabled with the same function.
Fixes: e53e597fd4 ("tty: pl011: fix earlycon work-around for QDF2400 erratum 44")
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Cc: stable <stable@vger.kernel.org> # 4.11
Tested-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add method, which waits until the transmission buffer has been sent.
Note, that the change in ttyport_write_wakeup is related, since
tty_wait_until_sent will hang without that change.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The UPF_BOOT_AUTOCONF flag is needed for proper
flow control support.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since forever, gpm was this code's only user, and it overrides the table on
start so the default was never seen -- until Bill Allombert's "consolation"
came in. The in-kernel set is "A-Za-z0-9_" which fails to catch typical
file names, etc. Let's change this to gpm's conservative default, ie
"-A-Za-z0-9_./"; most terminals include more, for example xfce4-terminal has
"-A-Za-z0-9,./?%&#:_=+@~".
There's some discussion at https://bugs.debian.org/846587
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce RX DMA start latency for the first reception when port is opened
for reading. Instead of waiting for an interrupt signaling data on RX
FIFO or data too old on RX FIFO, start RX DMA immediately when the
serial port is opened for reading.
Before this patch, the average RX DMA latency for the first reception
was 42489 microseconds with a standard deviation of 25721 microseconds
in 36 samples.
After the patch the average RX DMA latency for the first reception, when
the serial port is opened for reading, is 653 microseconds with a
standard deviation of 294 microseconds in 36 samples.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to actually suspend the device before returning after a failed
(or deferred) probe.
Note that autosuspend must be disabled before runtime pm is disabled in
order to balance the usage count due to a negative autosuspend delay as
well as to make the final put suspend the device synchronously.
Fixes: 388bc26226 ("omap-serial: Fix the error handling in the omap_serial probe")
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An unbalanced and misplaced synchronous put was used to suspend the
device on driver unbind, something which with a likewise misplaced
pm_runtime_disable leads to external aborts when an open port is being
removed.
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa024010
...
[<c046e760>] (serial_omap_set_mctrl) from [<c046a064>] (uart_update_mctrl+0x50/0x60)
[<c046a064>] (uart_update_mctrl) from [<c046a400>] (uart_shutdown+0xbc/0x138)
[<c046a400>] (uart_shutdown) from [<c046bd2c>] (uart_hangup+0x94/0x190)
[<c046bd2c>] (uart_hangup) from [<c045b760>] (__tty_hangup+0x404/0x41c)
[<c045b760>] (__tty_hangup) from [<c045b794>] (tty_vhangup+0x1c/0x20)
[<c045b794>] (tty_vhangup) from [<c046ccc8>] (uart_remove_one_port+0xec/0x260)
[<c046ccc8>] (uart_remove_one_port) from [<c046ef4c>] (serial_omap_remove+0x40/0x60)
[<c046ef4c>] (serial_omap_remove) from [<c04845e8>] (platform_drv_remove+0x34/0x4c)
Fix this up by resuming the device before deregistering the port and by
suspending and disabling runtime pm only after the port has been
removed.
Also make sure to disable autosuspend before disabling runtime pm so
that the usage count is balanced and device actually suspended before
returning.
Note that due to a negative autosuspend delay being set in probe, the
unbalanced put would actually suspend the device on first driver unbind,
while rebinding and again unbinding would result in a negative
power.usage_count.
Fixes: 7e9c8e7dbf ("serial: omap: make sure to suspend device before remove")
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UPF_BOOT_AUTOCONF flag is needed for proper
flow control support.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Spinlock taken only for dma_map_single() for TX buffer is completely
useless and doesn't protect anything, so remove it to simplify the code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds missing checks for dma_map_single() failure and proper error
reporting. Although this issue was harmless on ARM architecture, it is always
good to use the DMA mapping API in a proper way. This patch fixes the following
DMA API debug warning:
WARNING: CPU: 1 PID: 3785 at lib/dma-debug.c:1171 check_unmap+0x8a0/0xf28
dma-pl330 121a0000.pdma: DMA-API: device driver failed to check map error[device address=0x000000006e0f9000] [size=4096 bytes] [mapped as single]
Modules linked in:
CPU: 1 PID: 3785 Comm: (agetty) Tainted: G W 4.11.0-rc1-00137-g07ca963-dirty #59
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c011aaa4>] (unwind_backtrace) from [<c01127c0>] (show_stack+0x20/0x24)
[<c01127c0>] (show_stack) from [<c06ba5d8>] (dump_stack+0x84/0xa0)
[<c06ba5d8>] (dump_stack) from [<c0139528>] (__warn+0x14c/0x180)
[<c0139528>] (__warn) from [<c01395a4>] (warn_slowpath_fmt+0x48/0x50)
[<c01395a4>] (warn_slowpath_fmt) from [<c072a114>] (check_unmap+0x8a0/0xf28)
[<c072a114>] (check_unmap) from [<c072a834>] (debug_dma_unmap_page+0x98/0xc8)
[<c072a834>] (debug_dma_unmap_page) from [<c0803874>] (s3c24xx_serial_shutdown+0x314/0x52c)
[<c0803874>] (s3c24xx_serial_shutdown) from [<c07f5124>] (uart_port_shutdown+0x54/0x88)
[<c07f5124>] (uart_port_shutdown) from [<c07f522c>] (uart_shutdown+0xd4/0x110)
[<c07f522c>] (uart_shutdown) from [<c07f6a8c>] (uart_hangup+0x9c/0x208)
[<c07f6a8c>] (uart_hangup) from [<c07c426c>] (__tty_hangup+0x49c/0x634)
[<c07c426c>] (__tty_hangup) from [<c07c78ac>] (tty_ioctl+0xc88/0x16e4)
[<c07c78ac>] (tty_ioctl) from [<c03b5f2c>] (do_vfs_ioctl+0xc4/0xd10)
[<c03b5f2c>] (do_vfs_ioctl) from [<c03b6bf4>] (SyS_ioctl+0x7c/0x8c)
[<c03b6bf4>] (SyS_ioctl) from [<c010b4a0>] (ret_fast_syscall+0x0/0x3c)
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Fixes: 62c37eedb7 ("serial: samsung: add dma reqest/release functions")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver should provide its own struct device for all DMA-mapping calls instead
of extracting device pointer from DMA engine channel. Although this is harmless
from the driver operation perspective on ARM architecture, it is always good
to use the DMA mapping API in a proper way. This patch fixes following DMA API
debug warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1241 check_sync+0x520/0x9f4
samsung-uart 12c20000.serial: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000006df0f580] [size=64 bytes]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1-00137-g07ca963 #51
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c011aaa4>] (unwind_backtrace) from [<c01127c0>] (show_stack+0x20/0x24)
[<c01127c0>] (show_stack) from [<c06ba5d8>] (dump_stack+0x84/0xa0)
[<c06ba5d8>] (dump_stack) from [<c0139528>] (__warn+0x14c/0x180)
[<c0139528>] (__warn) from [<c01395a4>] (warn_slowpath_fmt+0x48/0x50)
[<c01395a4>] (warn_slowpath_fmt) from [<c0729058>] (check_sync+0x520/0x9f4)
[<c0729058>] (check_sync) from [<c072967c>] (debug_dma_sync_single_for_device+0x88/0xc8)
[<c072967c>] (debug_dma_sync_single_for_device) from [<c0803c10>] (s3c24xx_serial_start_tx_dma+0x100/0x2f8)
[<c0803c10>] (s3c24xx_serial_start_tx_dma) from [<c0804338>] (s3c24xx_serial_tx_chars+0x198/0x33c)
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Fixes: 62c37eedb7 ("serial: samsung: add dma reqest/release functions")
CC: stable@vger.kernel.org # v4.0+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the UART is operated in DTE mode and UCR3_DCD or UCR3_RI are 1 (which
is the reset default) and the opposite side pulls the respective line to
its active level the irq triggers after it is requested in .probe.
These irqs were already disabled in .startup but this might be too late.
Also setup of the UFCR_DCEDTE bit (currently done in .set_termios) is
done very late which is critical as it also controls direction of some
pins.
So setup UFCR_DCEDTE earlier (in .probe) and also disable the broken
irqs in DTE mode there before requesting irqs.
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SMP systems, we see a lot of spurious TX interrupts when a
program generates a steady stream of output to the pl011 UART.
The problem can be easily seen when one CPU generates the output
while another CPU handles the pl011 interrupts, and the rate of
output is low enough not to fill the TX FIFO. The problem seems
to be:
-- CPU a -- -- CPU b --
(take port lock)
pl011_start_tx
pl011_start_tx_pio
enable TXIM in REG_IMSC -> causes uart tx intr (pl011_int)
pl011_tx_chars pl011_int
...tx chars, all done... (wait for port lock)
pl011_stop_tx .
disable TXIM .
(release port lock) -> (take port lock)
check for TXIM, not enabled
(release port lock)
return IRQ_NONE
Enabling the TXIM in pl011_start_tx_pio() causes the interrupt
to be generated and delivered to CPU b, even though pl011_tx_chars()
is able to complete the TX and then disable the tx interrupt.
Fix this by enabling TXIM only after pl011_tx_chars, if it is needed.
pl011_tx_chars will return a boolean indicating whether the TX
interrupts have to be enabled.
Debugged-by: Vijaya Kumar <Vijaya.Kumar@cavium.com>
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Power management is disabled then the clocks are not getting
enabled. This patch enables it for the !PM case also.
While at it also pm_runtime_set_active is called before
calling pm_runtime_enable.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have port name stored in struct uart_port, we better to use
that one instead of open coding.
This will make it one place source for easier maintenance or
modifications.
While here, replace printk(KERN_INFO ) by pr_info(). It seems last printk()
call in serial_core.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serdev_device_write() a blocking call allowing to transfer
arbitraty amount of data (potentially exceeding amount that
serdev_device_write_buf can process in a single call)
To support that, also add serdev_device_write_wakeup().
Drivers wanting to use full extent of serdev_device_write
functionality are expected to provide serdev_device_write_wakeup() as
a sole handler of .write_wakeup event or call it as a part of driver's
custom .write_wakeup code.
Because serdev_device_write() subroutine is a superset of
serdev_device_write_buf() the patch re-impelements latter is terms of
the former. For drivers wanting to just use serdev_device_write_buf()
.write_wakeup handler is optional.
Cc: cphealy@gmail.com
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPRD_TIMEOUT was 256, which is too small to wait until the status
switched to workable in a while loop, so that the earlycon could
not work correctly.
Signed-off-by: Wei Qiao <wei.qiao@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit d6580a9f15 ("kexec: sysrq: simplify sysrq-c handler"),
the sysrq handler for the 'c' key has been sysrq_crash_op. Debugging
code in the ibm_emac driver also tries to register a handler for the 'c'
key, but this has no effect because register_sysrq_key() doesn't replace
existing handlers. Since evidently no one has cared enough to fix this
in the last 8 years, and it's very rare for drivers to register sysrq
handlers (for good reason), just remove the dead code.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler fixes from Thomas Gleixner:
"This update provides:
- make the scheduler clock switch to unstable mode smooth so the
timestamps stay at microseconds granularity instead of switching to
tick granularity.
- unbreak perf test tsc by taking the new offset into account which
was added in order to proveide better sched clock continuity
- switching sched clock to unstable mode runs all clock related
computations which affect the sched clock output itself from a work
queue. In case of preemption sched clock uses half updated data and
provides wrong timestamps. Keep the math in the protected context
and delegate only the static key switch to workqueue context.
- remove a duplicate header include"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/headers: Remove duplicate #include <linux/sched/debug.h> line
sched/clock: Fix broken stable to unstable transfer
sched/clock, x86/perf: Fix "perf test tsc"
sched/clock: Fix clear_sched_clock_stable() preempt wobbly
The work-around for the Qualcomm Datacenter Technologies QDF2400
erratum 44 sets the "qdf2400_e44_present" global variable if the
work-around is needed. However, this check does not happen until after
earlycon is initialized, which means the work-around is not
used, and the console hangs as soon as it displays one character.
Fixes: d8a4995bce ("tty: pl011: Work around QDF2400 E44 stuck BUSY bit")
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit d0aeaa83f0 ("serial: exar:
split out the exar code from 8250_pci") the exar driver got its own
Kconfig. However the text for the new option was never changed from
the original 8250_PCI text, and hence it appears confusing when you
get asked the same question twice:
8250/16550 PCI device support (SERIAL_8250_PCI) [Y/n/m/?] (NEW)
8250/16550 PCI device support (SERIAL_8250_EXAR) [Y/n/m] (NEW)
Adding to the confusion, is that there is no help text for this new
option to indicate it is specific to a certain family of cards.
Fix both issues at the same time, as well as the space vs. tab issues
introduced in the same commit.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A side effect of 89d8232411 ("tty/serial: atmel_serial: BUG: stop DMA
from transmitting in stop_tx") is that the console can be called with
TX path disabled. Then the system would hang trying to push charecters
out in atmel_console_putchar().
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 89d8232411 ("tty/serial: atmel_serial: BUG: stop DMA from transmitting
in stop_tx")
Cc: stable <stable@vger.kernel.org> #4.4+
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If uart_flush_buffer() is called between atmel_tx_dma() and
atmel_complete_tx_dma(), the circular buffer has been cleared, but not
atmel_port->tx_len.
That leads to a circular buffer overflow (dumping (UART_XMIT_SIZE -
atmel_port->tx_len) bytes).
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reference manual for the i.MX28 recommends to calculate the divisor
as
divisor = (UARTCLK * 32) / baud rate, rounded to the nearest integer
, so let's do this. For a typical setup of UARTCLK = 24 MHz and baud
rate = 115200 this changes the divisor from 6666 to 6667 and so the
actual baud rate improves from 115211.521 Bd (error ≅ 0.01 %) to
115194.240 Bd (error ≅ 0.005 %).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console write code is not entirely race free (e.g. the operations
to disabling the UART interrupts are not atomic) hence locking is
required. This has been become apparent with the PREEMPT RT patchset
applied: With the fully preemptible kernel configuration the system
often ended up in a freeze already at startup.
Disable interrupts and lock using read_lock_irqsave. Try to lock in
the sysrq/oops case, but don't bother if locking fails.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nios2 currently uses its own early printk implementation, rather than
using unified earlycon support to show boot messages on altera_uart.
Add earlycon support to altera_uart so that other archs may use it.
Also, this (together with the corresponding patch for altera_jtaguart)
will allow the early printk implementation in arch/nios2 to be removed
in a future patch.
Cc: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BugLink: http://bugs.launchpad.net/bugs/869017
Console blanking is not enabling DPMS power saving (thereby negating any
power-saving benefit), and is simply turning the screen content blank. This
means that any crash output is invisible which is unhelpful on a server
(virtual or otherwise).
Furthermore, CRT burn in concerns should no longer govern the default case.
Affected users could always set consoleblank on the kernel command line.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Adam Borowski <kilobyte@angband.pl>
Cc: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using dev_name() as IRQ name during request_irq() might be misleading in
case of serial over PCI. Therefore identify serial port IRQ using
uart_port's name field. This will help mapping IRQs to appropriate
ttySN(where N is the serial port index) instances.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman