Initialize asm_irq_flags in omap_init_irq and use it in
get_irqnr_and_base to detect between omap7xx and omap15xx/16xx.
Note that both INT_1510_IH2_IRQ and INT_1510_IH2_IRQ are defined
as 0, so use INT_1510_IH2_IRQ for both of them.
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7c63984b86 (ARM: do not define VMALLOC_END relative to PAGE_OFFSET)
changed VMALLOC_END to be an explicit value. Before this, it was
relative to PAGE_OFFSET and therefore converted to unsigned long
as PAGE_OFFSET is an unsigned long. This introduced the following
build warning. Fix this by changing the explicit defines of
VMALLOC_END to be unsigned long.
CC arch/arm/mm/init.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Uwe Kleine-K <u.kleine-koenig@pengutronix.dee>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
#include <media/omap1_camera.h> directive is required to
compile the dependant boards (board-ams-delta for now).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
VMALLOC_END is supposed to be an absolute value, while PAGE_OFFSET may
vary depending on the selected user:kernel memory split mode through
CONFIG_VMSPLIT_*. In fact, the goal of moving PAGE_OFFSET down is to
accommodate more directly addressed RAM by the kernel below the vmalloc
area, and having VMALLOC_END move along PAGE_OFFSET is rather against
the very reason why PAGE_OFFSET can be moved in the first place.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This patch adds a definition of the OMAP1 camera interface platform device,
and a function that allows for providing a board specific platform data.
The device will be used with the upcoming OMAP1 SoC camera interface driver.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now we use a memory address to store the debug port info, So we need
to read/write this address when we choose DEBUG_LL. When MMU isn't
enable(I.E. the begining part of init stage of the linux kernel boot),
we need to access physical address instead of virtual address,
otherwise the kernel will crash.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch introduces an IRQ handler used for processing interrupts generated
by the FIQ handler when it decides there are data ready for processing.
The handler further invokes device specific interrupt routines based on
interrupt source counters passed from the FIQ handler.
The handler setup function is intended to be called from the board
provided init_machine() callback.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: Updated to include linux/io.h instead of plat/io.h
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch introduces a Fast Interrupt Request (FIQ) handler for Amstrad Delta
(E3) videophone. The handler's purpose is to process interrupts generated by a
GPIO line that a serial keyboard clock hangs off. It collects consecutive bits
into words, pushing them into a buffer, then requests a higher level interrupt
after one or more words are ready for further processing by a keyboard port
driver.
The handler also processes interrupts generated by two other GPIO lines, used
by other on-board supported devices, by simply requesting a higher level
interrupt, that in turn should invoke those device's specific irq handlers.
IRQ12 line, not used by OMAP1510 hardware (described as reserved), has been
choosen as a higher level interrupt source.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This removes the dependency to the UART1 being available for storing
the debug configuration in uncompress.h. This will simplify the
DEBUG_LL UART configuration for boards that may not have UART1, or
have an external UART as it requires only one mapping for DEBUG_LL.
The patch has a few limitations. Basically now we're assuming that
the kernel uncompress code won't overlap with OMAP_UART_INFO. We also
assume the printascii is called at least once before paging_init in
order for addruart to have a chance to read the UART setup from
OMAP_UART_INFO.
As suggested by Cyril Chemparathy <cyril@ti.com>,
Vikram Pandita <vikram.pandita@ti.com> and
Kevin Hilman <khilman@deeprootsystems.com>. Based on an earlier
patch posted for Davinci by Cyril Chemparathy <cyril@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we don't have conflicts with the defines
with compiling in multiple omaps. Set the addresses
for uarts in struct omap_globals for the early serial
init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch corrects the issue introduced with one of my earlier patches:
OMAP: DMA: Fix omapfb/lcdc on OMAP1510 broken when PM set[1]
as pointed out by OMAP subsystem maintainer.
Applies on top of my prevoius patch:
OMAP: DMA: move LCD DMA related code from plat-omap to mach-omap1[2]
Tested on Amstrad Delta
Compile tested with omap_generic_2420_defconfig
[1] http://patchwork.kernel.org/patch/57922/
[2] http://patchwork.kernel.org/patch/61952/
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).
Move this code to mach-omap1/lcd_dma.c.
Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Create the headers needed for compiling under
mach-omap1/include/mach and mach-omap2/include/mach.
This was done with the following script:
#!/bin/bash
mach_files="clkdev.h gpio.h hardware.h io.h irqs.h memory.h \
smp.h system.h timex.h uncompress.h vmalloc.h"
omaps="mach-omap1 mach-omap2"
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
mkdir -p $plat_dir_new
git add $plat_dir_new
for dir in $omaps; do
mach_dir_new="arch/arm/$dir/include/mach"
for header in $mach_files; do
file="$mach_dir_new/$header"
if [ ! -f $file ]; then
echo -ne "/*\n * $file\n */\n\n#include <plat/$header>\n" > $file
git add $file
if [ ! -f $plat_dir_new/$header ]; then
git mv $mach_dir_old/$header $plat_dir_new/$header
fi
fi
done
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Earlier patch "omap: Remap L3, L4 to get more kernel io address space"
changed the VMALLOC_END.
However, this change causes problems on mach-omap1:
BUG: mapping for 0xe0000000 at 0xe0000000 overlaps vmalloc space
BUG: mapping for 0xe1000000 at 0xe1000000 overlaps vmalloc space
Fix this by creating separate vmalloc.h files for mach-omap1
and mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren