Set the min_freq_softlimit to max(RPe, 450MHz).
Setting a floor can ensure a minimum experience
level. The 450MHz value came from a power and
performance study of various types of workloads
(3D, Media, GPGPU, idle, etc).
v2: rebased
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added gen6_init_rps_frequencies() to initialize
the rps frequency values. This function replaces
parse_rp_state_cap(). In addition to reading RPn,
RP0, and RP1 from RP_STATE_CAP register, the new
function reads efficient frequency (aka RPe) from
pcode for Haswell and Broadwell and sets the turbo
softlimits. The turbo minimum frequency softlimit
is set to RPe for Haswell and Broadwell and to RPn
otherwise.
For RPe, the efficiency is based on the frequency/power
ratio (MHz/W); this is considering GT power and not
package power. The efficent frequency is the highest
frequency for which the frequency/power ratio is within
some threshold of the highest frequency/power ratio.
A fixed decrease in frequency results in smaller
decrease in power at frequencies less than RPe than
at frequencies above RPe.
v2: Following suggestions from Chris Wilson and
Daniel Vetter to extend and rename parse_rp_state_cap
and to open-code a poorly named function.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Remove unused variables.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Found one more!
With this we can clear up the ggtt init code a bit, yay!
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
With this all the ums nonsense around gem setup/teardown has
disappeared, yay!
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Again just complicates gem init functions and makes a general mess out
of everything.
Good riddance!
v2: In my enthusiasm to start removing dri1/ums crud I went overboard a
bit and killed parts of hangcheck. Resurrect it.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We've killed ums support by now, it's time to reap the benefits. This
one here is getting in the way of doing some ring init cleanup.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
KMS always intializes, this was only a valid check when userspace
was still in control of the kernel driver.
v2: Comment that we outright reject all dri1/ums params.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whether we'll reject them or no-op doesn't really matter ...
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the deprecation of UMS, and by association DRI1, we have a tough
choice when updating the ring access routines. We either rewrite the
DRI1 routines blindly without testing (so likely to be broken) or take
the liberty of declaring them no longer supported and remove them
entirely. This takes the latter approach.
v2: Also remove the DRI1 sarea updates
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fix rebase conflicts.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as with the context, pinning to GGTT regardless is harmful (it
badly fragments the GGTT and can even exhaust it).
Unfortunately, this case is also more complex than the previous one
because we need to map and access the ringbuffer in several places
along the execbuffer path (and we cannot make do by leaving the
default ringbuffer pinned, as before). Also, the context object
itself contains a pointer to the ringbuffer address that we have to
keep updated if we are going to allow the ringbuffer to move around.
v2: Same as with the context pinning, we cannot really do it during
an interrupt. Also, pin the default ringbuffers objects regardless
(makes error capture a lot easier).
v3: Rebased. Take a pin reference of the ringbuffer for each item
in the execlist request queue because the hardware may still be using
the ringbuffer after the MI_USER_INTERRUPT to notify the seqno update
is executed. The ringbuffer must remain pinned until the context save
is complete. No longer pin and unpin ringbuffer in
populate_lr_context() - this transient address is meaningless and the
pinning can cause a sleep while atomic.
v4: Moved ringbuffer pin and unpin into the lr_context_pin functions.
Downgraded pinning check BUG_ONs to WARN_ONs.
v5: Reinstated WARN_ONs for unexpected execlist states. Removed unused
variable.
Issue: VIZ-4277
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Up until now, we have pinned every logical ring context backing object
during creation, and left it pinned until destruction. This made my life
easier, but it's a harmful thing to do, because we cause fragmentation
of the GGTT (and, eventually, we would run out of space).
This patch makes the pinning on-demand: the backing objects of the two
contexts that are written to the ELSP are pinned right before submission
and unpinned once the hardware is done with them. The only context that
is still pinned regardless is the global default one, so that the HWS can
still be accessed in the same way (ring->status_page).
v2: In the early version of this patch, we were pinning the context as
we put it into the ELSP: on the one hand, this is very efficient because
only a maximum two contexts are pinned at any given time, but on the other
hand, we cannot really pin in interrupt time :(
v3: Use a mutex rather than atomic_t to protect pin count to avoid races.
Do not unpin default context in free_request.
v4: Break out pin and unpin into functions. Fix style problems reported
by checkpatch
v5: Remove unpin_lock as all pinning and unpinning is done with the struct
mutex already locked. Add WARN_ONs to make sure this is the case in future.
Issue: VIZ-4277
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No longer create a work item to clean each execlist queue item.
Instead, move retired execlist requests to a queue and clean up the
items during retire_requests.
v2: Fix legacy ring path broken during overzealous cleanup
v3: Update idle detection to take execlists queue into account
v4: Grab execlist lock when checking queue state
v5: Fix leaking requests by freeing in execlists_retire_requests.
Issue: VIZ-4274
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So with all the code movement and extraction in intel_pm.c in -next
git is hopelessly confused with
commit 2208d655a9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Nov 14 09:25:29 2014 +0100
drm/i915: drop WaSetupGtModeTdRowDispatch:snb
from -fixes. Worse even small changes in -next move around the
conflict context so rerere is equally useless. Let's just backmerge
and be done with it.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Except for git getting lost no tricky conflicts really.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
After the previous patch RPS disabling doesn't depend any more on the
first level interrupts being disabled, so we can move it everywhere
earlier. Doing so let's us think about the uninitialization steps
afterwards independently of any asynchronous RPS events that can happen
atm. It also makes the system/runtime suspend time RPS disabling more
uniform. Finally this gets rid of the WARN in
intel_suspend_gt_powersave(), which we can hit if a final RPS work runs
after we disabled the first level interrupts.
Testcase: igt/pm_rpm
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When disabling the RPS interrupts there is a tricky dependency between
the thread disabling the interrupts, the RPS interrupt handler and the
corresponding RPS work. The RPS work can reenable the interrupts, so
there is no straightforward order in the disabling thread to (1) make
sure that any RPS work is flushed and to (2) disable all RPS
interrupts. Currently this is solved by masking the interrupts using two
separate mask registers (first level display IMR and PM IMR) and doing
the disabling when all first level interrupts are disabled.
This works, but the requirement to run with all first level interrupts
disabled is unnecessary making the suspend / unload time ordering of RPS
disabling wrt. other unitialization steps difficult and error prone.
Removing this restriction allows us to disable RPS early during suspend
/ unload and forget about it for the rest of the sequence. By adding a
more explicit method for avoiding the above race, it also becomes easier
to prove its correctness. Finally currently we can hit the WARN in
snb_update_pm_irq(), when a final RPS work runs with the first level
interrupts already disabled. This won't lead to any problem (due to the
separate interrupt masks), but with the change in this and the next
patch we can get rid of the WARN, while leaving it in place for other
scenarios.
To address the above points, add a new RPS interrupts_enabled flag and
use this during RPS disabling to avoid requeuing the RPS work and
reenabling of the RPS interrupts. Since the interrupt disabling happens
now in intel_suspend_gt_powersave(), we will disable RPS interrupts
explicitly during suspend (and not just through the first level mask),
but there is no problem doing so, it's also more consistent and allows
us to unify more of the RPS disabling during suspend and unload time in
the next patch.
v2/v3:
- rebase on patch "drm/i915: move rps irq disable one level up" in the
patchset
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we first enable the RPS interrupts then we clear any pending ones.
By this we could lose an interrupt arriving after we unmasked it. This
may not be a problem as the caller should handle such a race, but logic
still calls for the opposite order. Also we can delay enabling the
interrupts until after all the RPS initialization is ready with the
following order:
1. disable left-over RPS (earlier via intel_uncore_sanitize)
2. clear any pending RPS interrupts
3. initialize RPS
4. enable RPS interrupts
This also allows us to do the 2. and 4. step the same way for all
platforms, so let's follow this order to simplifying things.
Also make sure any queued interrupts are also cleared.
v2:
- rebase on the GEN9 patches where we don't support RPS yet, so we
musn't enable RPS interrupts on it (Paulo)
v3:
- avoid enabling RPS interrupts on GEN>9 too (Paulo)
- clarify the RPS init sequence in the log message (Chris)
- add POSTING_READ to gen6_reset_rps_interrupts() (Paulo)
- WARN if any PM_IIR bits are set in gen6_enable_rps_interrupts()
(Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable the RPS interrupts for all platforms at the same spot, so
move it one level up in the callstack to simplify things.
No functional change.
v2:
- rebase on the GEN9 patches where RPS isn't supported yet, so we don't
need to disable RPS interrupts on it (Paulo)
v3:
- avoid disabling the interrupts on GEN>9 too (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This extends
commit 132f3f1767
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Nov 10 15:34:33 2014 +0200
drm/i915: WARN if we receive any gen9 rps interrupts
to GEN>9 platforms as suggested by Paulo.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When using the universal plane interface, the source rectangle
coordinates define the panning offset for the primary plane, which needs
to be stored in crtc->{x,y}. The original universal plane code
negelected to set these panning offset fields, which was partially
remedied in:
commit ccc759dc2a
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Wed Sep 24 14:20:22 2014 -0300
drm/i915: Merge of visible and !visible paths for primary planes
However the plane source coordinates are provided in 16.16 fixed point
format and the above commit forgot to convert back to integer
coordinates before saving the values. When we replace
intel_pipe_set_base() with plane->funcs->update_plane() in a future
patch, this bug becomes visible via the set_config entrypoint as well as
update_plane.
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Testcase: igt/kms_plane
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like we do in the HDMI code, set the infoframe flag if we detect
that infoframes are enabled.
v2: check for actual infoframe status as in hdmi code (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In sandybridge_pcode_read and sandybridge_pcode_write,
extend the mbox parameter from u8 to u32.
On Haswell and Sandybridge, bits 7:0 encode the mailbox
command and bits 28:8 are used for address control for
specific commands.
Based on suggestion from Ville Syrjälä.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For whatever reasons this can happen. For real testcases the test will
notice the -EIO and fall over, but we also have some testcases that
just read all debugfs files. And that shouldn't cause dmesg spam.
So tune it down a bit so that we still have the information for
debugging. And change the errno so that real testcases can easily
differentiate.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84890
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
With multiple rings, we may continue to render on the blitter whilst
executing an infinite shader on the render ring. As we currently, rearm
the timer with each execbuf, in this scenario the hangcheck will never
fire and we will never detect the lockup on the render ring. Instead,
only arm the timer once per hangcheck, so that hangcheck runs more
frequently.
v2: Rearrange code to avoid triggering a BUG_ON in add_timer from
softirq context.
Testcase: igt/gem_reset_stats/defer-hangcheck*
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86225
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This goes back to
commit 362b8af7ad
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Thu Jan 30 00:19:38 2014 -0800
drm/i915: Move per ring error state to ring_error
Spotted while reading error states.
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Indicate the monitor has been disconnected on disable.
The regression has been introduced in
commit 5fad84a753
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Nov 4 10:30:23 2014 +0200
drm/i915: rewrite hsw/bdw audio codec enable/disable sequences
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86424
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The lack of a break here wasn't for falling through to some other
important code, so made me do a double take. Add a break just to make
things a little less confusing.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
kmap never fails.
Spotted-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When invalid cloning configurations were detected during modeset, we
never copied the error code into the return value variable, leading us
to return 0 (success) to userspace.
This regression has been introduced in
commit 50f5275698
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Nov 7 13:11:00 2014 -0800
drm/i915: use compute_config in set_config v4
Testcase: igt/kms_setmode
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86226
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL DPLL0 is used to derive CDCLK but can also be used to drive an
eDP port (as long as we don't want SSC). DPLL0 is special enough to not
be handled by the shared DPLL framework (drives CDCLK, not supposed to
enable the HDMI mode), So we need to compute the configuration
separately from the other DPLLs.
Note that we don't need to reprogram DPLL0 (which would mean bringing
down CDCLK) to support the various eDP 1.3 link rates as they all share
the same VCO (8100).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's document PSR a bit. No functional changes.
v2: Add actual DocBook entry and accept Daniel's improvements.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes. Just cleaning and reorganizing it.
v2: Rebase it puting it to begin of psr rework. This helps to blame easily
at least latest changes.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional change. Just making it public for use outside intel_dp.c
Allowing split psr functions.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN6_GT_THREAD_STATUS_REG doesn't seem to exist on VLV. Reads just give
0x0 no matter what the state of the render and media wells.
There was also some hint in the Gunit HAS that thread status not being
needed on VLV, and hence dropped when bringing stuff over from the IVB
design. Not really a definite comment about the specific register itself
though.
Also the w/a itself is no longer listed for VLV in the database. It was
there some time ago in the past, but I guess someone figured out the
mistake and dropped it.
So let's just drop it from the code as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits [18:16] of GEN6_GT_THREAD_STATUS_REG have always had the same
meaning since SNB. So treating them as something special for HSW doesn't
make sense to me.
Also the bits *seem* to work exactly the same way on IVB, HSW GT2 and
HSW GT3. At least intel_reg_read gives the identical results on all
platforms with and without forcewake.
Also the HSW PM guide rev 0.99 (ww05 2013) doesn't say anything about
those bits. It just says to poll for bits [2:0]. As does the more recent
BDW PM guide.
So just drop the HSW special case and treat all platforms the same way.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When reading out a DDI config that uses a PLL that is not part of the
shared_dpll scheme (DPLL0), it's totally normal to end up in the
default: case of that switch.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to "Cherryview_GFXclocks_y14w36d1.xlsx" the GPU frequency
divider should be 10 in when the CZ clock is 400 MHz. Change the code
to agree so that we report the correct frequencies.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The divider used in the GPU frequency calculations is compatible between
vlv and chv. vlv just wants doubled values compared to chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always print the final PCBR register value on both vlv and chv, and
also tell us whether the BIOS was a good citizen or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our freq<->opcode conversions assume that GPLL is always used.
Apparently that should be the case always, but let's scream if we
ever encounter something different.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the magic number for the GPLLENABLE bit by adding a name for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even with the rps debug messages signficantly recuced by
commit 67956867aa
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Tue Sep 2 15:12:17 2014 +0300
drm/i915: Don't spam dmesg with rps messages on vlv/chv
we still get an inordinate amount of spam from this. Just kill the debug
print. If someone wants to observe it they can just use the tracepoint.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's magic, but it seems to work.
This fixes a regression introduced in
commit 1bb9e632a0
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 8 10:02:43 2014 +0200
drm/i915: Only unbind vgacon, not other console drivers
My best guess is that the vga fbdev driver falls over if we rip out
parts of vgacon. Hooray.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82439
Cc: stable@vger.kernel.org (v3.16+)
Reported-and-tested-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts the regressing
commit 6547fbdbff
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Dec 14 23:38:29 2012 +0100
drm/i915: Implement WaSetupGtModeTdRowDispatch
that causes GPU hangs immediately on boot.
Reported-by: Leo Wolf <jclw@ymail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79996
Cc: stable@vger.kernel.org (v3.8+)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
[Jani: amended the commit message slightly.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On chv the pipe-a power well is the new disp2d well, and it kills pretty
much everything in the display block. So we need to do the the same
dance that vlv does wrt. display irqs and hpd when the power well goes
up or down.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a small collection of fixes that I've been carrying around for a
while now. Many of these have been posted and reviewed or acked. The few
that haven't I deemed too trivial to bother.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=OUaP
-----END PGP SIGNATURE-----
Merge tag 'drm/fixes/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux into drm-next
drm: Miscellaneous fixes for v3.19-rc1
This is a small collection of fixes that I've been carrying around for a
while now. Many of these have been posted and reviewed or acked. The few
that haven't I deemed too trivial to bother.
* tag 'drm/fixes/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux:
video/hdmi: Relicense header under MIT license
drm/gma500: mdfld: Reuse video/mipi_display.h
drm: Make drm_mode_create_tv_properties() signature consistent
drm: Implement drm_get_pci_dev() dummy for !PCI
drm/prime: Use unsigned type for number of pages
drm/gem: Fix typo in kerneldoc
drm: Use const data when creating blob properties
drm: Use size_t for blob property sizes
- skl watermarks code (Damien, Vandana, Pradeep)
- reworked audio codec /eld handling code (Jani)
- rework the mmio_flip code to use the vblank evade logic and wait for rendering
using the standard wait_seqno interface (Ander)
- skl forcewake support (Zhe Wang)
- refactor the chv interrupt code to use functions shared with vlv (Ville)
- prep work for different global gtt views (Tvrtko Ursulin)
- precompute the display PLL config before touching hw state (Ander)
- completely reworked panel power sequencer code for chv/vlv (Ville)
- pre work to split the plane update code into a prepare and commit phase
(Gustavo Padovan)
- golden context for skl (Armin Reese)
- as usual tons of fixes and improvements all over
* tag 'drm-intel-next-2014-11-07-fixups' of git://anongit.freedesktop.org/drm-intel: (135 commits)
drm/i915: Use correct pipe config to update pll dividers. V2
drm/i915: Plug memory leak in intel_shared_dpll_start_config()
drm/i915: Update DRIVER_DATE to 20141107
drm/i915: Add gen to the gpu hang ecode
drm/i915: Cache HPLL frequency on VLV/CHV
Revert "drm/i915/vlv: Remove check for Old Ack during forcewake"
drm/i915: Make mmio flip wait for seqno in the work function
drm/i915: Make __wait_seqno non-static and rename to __i915_wait_seqno
drm/i915: Move the .global_resources() hook call into modeset_update_crtc_power_domains()
drm/i915/audio: add DOC comment describing HDA over HDMI/DP
drm/i915: make pipe/port based audio valid accessors easier to use
drm/i915/audio: add audio codec enable debug log for g4x
drm/i915/audio: add audio codec disable on g4x
drm/i915: enable audio codec after port
drm/i915/audio: add vlv/chv/gen5-7 audio codec disable sequence
drm/i915/audio: rewrite vlv/chv and gen 5-7 audio codec enable sequence
drm/i915/skl: Enable Gen9 RC6
drm/i915/skl: Gen9 Forcewake
drm/i915/skl: Log the order in which we flush the pipes in the WM code
drm/i915/skl: Flush the WM configuration
...
Replace the misinformed notes about CHV snoop behaviour with something
that's hopefully closer to reality.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Throw away the hand rolled display irq setup code on chv, and instead
just call vlv_display_irq_postinstall() and vlv_display_irq_uninstall().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull the vlv display irq uninstall code into a separate function, for
eventual sharing with chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Running the driver without execlists and hence PPGTT (either aliasing or
full) isn't a supported configuration on gen9+.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_ddi.c:955:41: sparse: constant 8400000000 is so big it is long
intel_ddi.c:955:53: sparse: constant 9000000000 is so big it is long
intel_ddi.c:955:65: sparse: constant 9600000000 is so big it is long
intel_ddi.c:1028:23: sparse: constant 9600000000 is so big it is long
intel_ddi.c:1031:23: sparse: constant 9000000000 is so big it is long
intel_ddi.c:1034:23: sparse: constant 8400000000 is so big it is long
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Given the history, there's some chance we'll keep the same WM code for a
bit (previously, we were able to reuse the same WM code from ILK to BDW,
so that sounds like a fair assumption).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Write and reads following the block changed use engine specific use counters
and unless that is matched here force wake use counting goes bad. Same
force wake is attempted to be taken twice which leads to at least time outs.
NOTE: Depending on feedback from hardware designers it may not be necessary
to grab force wakes on Gen9 here. But for Gen8 it is needed due to a race
between RC6 and ELSP writes.
v2: Added blitter force wake engine and made more future proof.
Added commit note.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville found out that the DATA1 register exists since SNB with some
scarce apparitions in the specs throughout the times. In his own words:
Also according to Bspec the mailbox data1 register already existed
since snb. The hsw cdclk change sequence also mentions that it should
be set to 0, but eg. the bdw IPS sequence doesn't mention it. I guess
in theory some pcode command might cause it to be clobbered, so I'm
thinking we should just explicitly set it to 0 for all platforms in
the pcode read/write functions
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The LRC increased in size on gen9. Make sure we return the right
size in get_lr_context_size()
v2. Corrected the size, should be 22 pages. I unintentionally mailed out
a test patch w/ size equaling 23 pages.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Michael H. Nguyen <michael.h.nguyen@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new AUX port irq bits where needed.
v2: Rebase on top of upstream changes
v3: Rebase on top of Oscar change to write IIR as soon as possible (Damien)
v4: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This moved around on SKL, so we need to make sure we read/write the
correct regs.
v2: fixup WIN_POS offsets (Paulo)
zero out WIN_POS reg at disable time (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuougseek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few bits have changed in MI_DISPLAY_FLIP to accomodate the new planes.
DE_RRMR seems to have kept its plane flip bits backward compatible.
v2: Rebase on top of nightly
v3: Rebase on top of nightly (minor conflict in i915_reg.h)
v4: Remove code that is now part of intel_crtc_page_flip()
Don't use BUG() in default:
Use intel_crtc->unpin_work->gtt_offset
(Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The eDP WA to stop link train based on port type is for HSW/BDW, not
required for SKL+.
Suggested by Satheesh
v2: Simplified the check befoe stop_link_train. Suggested by Satheesh.
v3: stop_link_train need not be called from intel_enable_ddi for gen >= 9
Suggested-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: rebase on top of the hw state flattening.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch implements SKL DPLL programming that includes:
- DPLL allocation
- wide range PLL calculation and programming
- DP link rate programming
- DDI to DPLL mapping
v2: Incorporated following changes
- Added vfunc for function required outside
- Fixed multiple comments in WRPLL calculation
v3: - Fix the DCO computation
- Move the initialization up to not clobber the computed values
- Use the correct macro for DP link rate programming.
- Use wait_for() to wait for the PLL locked bit
v4: Rebase on top of nigthly (Damien)
v5: A few code cleanups in the WRPLL computation (Damien)
- Use uint32_t when possible
- Use abs_diff() in the WRPLL computation
- Make the 64bits divisions use div64_u64()
- Fix typo in dco_central_feq_deviation (freq)
- Replace the chain of breaks with a goto
v6: Port of the patch to work on top of the shared DPLLs (Damien)
v7: Don't try to handle eDP in ddi_pll_select() (Damien)
v8: Modified as per review comments from Paulo (Satheesh)
v9: Rebase on top of Ander's clock computation staging work for atomic (Damien)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake deprecates the usage of PORT_CLK_SEL and we are advised to use
the new DPLL_CRTL2 for the DDI->PLL mapping.
v2: Modified as per review comments
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On skylake, DPLL 1, 2 and 3 can be used for DP and HDMI. The shared dpll
framework allows us to share those DPLLs among DDIs when possible.
The most tricky part is to provide a DPLL state that can be easily
compared. DPLL_CRTL1 is shared by all the DPLLs, 6 bits each. The
per-dpll crtl1 field of the hw state is then normalized to be the same
value if 2 DPLLs do indeed have identical values for those 6 bits.
v2: Port the code to the shared DPLL infrastructure (Damien)
v3: Rebase on top of Ander's clock computation staging work for atomic (Damien)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v2)
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Modify the implementation to query DPLL attached to a SKL port.
v2: Rebase on top of the run-time PM on DPMS series (Damien)
v3: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Fixup compilation due to the removal of the intel_ddi_dpll_id enum.
And add a fixme about the abuse of pipe_config here.
v3: Rebase on top of the hsw_ddi_clock_get() rename (Damien)
v4: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Determine programmed cd clock for SKL.
v2: Fix the LCPLL1 enable warning logic
v3: Rebase over the hsw pll rework.
v4: Rebase on top of the per-platform split (Damien)
v5: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding structure/enum for SKL clocking implementation.
v2: Addressed Damien's comment
- Removed internal structure from this header file
v3: Stove this into the generic intel_dpll_id enum and give them the established
DPLL_ID_ prefixes. (Daniel)
v4: - We'll only try to share DPLL1/2/3, leaving DPLL0 to eDP
- Use SKL in the skylake shared DPLL names
- Re-add the skl_dpll enum
(Damien)
v5: Remove SKL_DPLL_NONE (Daniel)
v6: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v4,v5)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v3)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines the necessary SKL registers for implementing the
new clocking mechanism.
v2: Addressed review comments by Damien
- Added code comment
- Introduced enum for WRPLL values
v3: Rebase on top of nightly (minor conflict in i915_reg.h)
v4: Use 0x, not 0X (Ville)
v5: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3,v4)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some machines may have a broken VBT or no VBT at all, but we still want
to use SSC there. So check for it and keep it enabled if we see it
already on. Based on an earlier fix from Kristian.
v2: honor modparam if set too (Daniel)
read out at init time and store for panel_use_ssc() use (Jesse)
v3: trust BIOS configuration over VBT like we do for DP (Jani)
Reported-by: Kristian Høgsberg <hoegsberg@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This has been invalidated in
commit 24f3a8cf77
Author: Akash Goel <akash.goel@intel.com>
Date: Tue Jun 17 10:59:42 2014 +0530
drm/i915: Added write-enable pte bit supportt
But despite that it's in the diff context no one noticed :(
Cc: Akash Goel <akash.goel@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Use the same conditions, group by features, add comments.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is not used within the driver, and merely saving/restoring these
registers isn't going to do any good anyway. In fact, it's possible it's
actively harmful. Any code enabling the feature should handle this
completely in the regular platform specific enable/disable backlight
functions.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
AFAICT i9xx_pfit_disable() on the GMCH display crtc disable path in
i9xx_crtc_disable() will always disable the panel fitter by writing 0 to
PFIT_CONTROL. The register save will always save/restore 0. Also we
completely recompue both in intel_gmch_panel_fitting so there's no way
we depend upon leftover bits.
Move the PFIT_CONTROL and PFIT_PGM_RATIOS save/restore to UMS
code. While at it, save/restore them both under the same conditions.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Make it a bit clearer that we nowhere depend upon these
bits.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The block was added for spin_lock_irqsave flags, but since the locking
was converted to spin_lock_irq variant, the block is no longer needed.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since RSTDBYCTL is only saved on non-KMS path in within i915_save_state,
move the restore in i915_restore_state for symmetry.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't save the panel power sequencer register on vlv/chv for two simple
reasons. First, these are the wrong registers to save to begin
with. Second, they are not restored anyway.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As per latest pm guide, we need to do this also on
past hsw.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Following the legacy ring submission example, update the
ring->init_context() hook to support the execlist submission mode.
v2: update to use the new workaround macros and cleanup unused code.
This takes care of both bdw and chv workarounds.
v2.1: Add missing call to init_context() during deferred context creation.
v3: Split init_context (emit) in legacy/lrc modes. For lrc, get the ringbuf
from the context (Mika/Daniel).
v4: Merge init_context interfaces back, the legacy mode only needs the ring,
but the lrc mode needs the ring and context (Mika).
Issue: VIZ-4092
Issue: GMIN-3475
Change-Id: Ie3d093b2542ab0e2a44b90460533e2f979788d6c
Cc: Deepak S <deepak.s@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Align function paramater lists properly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When reading a CCK register we should obviously read it from CCK not
Punit. This problem has been present ever since this of code was
introduced in
commit 67c3bf6f55
Author: Deepak S <deepak.s@linux.intel.com>
Date: Thu Jul 10 13:16:24 2014 +0530
drm/i915: populate mem_freq/cz_clock for chv
The problem was raised during review by Mika [1] but somehow slipped
through the cracks, and the patch got applied with the problem unfixed.
[1] http://lists.freedesktop.org/archives/intel-gfx/2014-July/048937.html
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The predicate source registers are needed to implement conditional
rendering without stalling. The two source registers are used to load
the previous values of the PS_DEPTH_COUNT register saved from
PIPE_CONTROL commands. These can then be compared and used to set the
predicate enable bit via the MI_PREDICATE command.
The command parser version number is increased to 2 to make it easier
to detect the new functionality in user space.
Signed-off-by: Neil Roberts <neil@linux.intel.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com> (v1)
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This only affects the fastboot path as-is. In that case, we simply need
to make sure that we update the pipe size at the first mode set. Rather
than putting it off until we decide to flip (if indeed we do end up
flipping), update the pipe size as appropriate a bit earlier in the
set_config call.
This sets us up for better pipe tracking in later patches.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If these change (e.g. after a modeset following a fastboot), we need to
do a full mode set.
v2:
- put under pipe_config check so we don't deref a null state (Jesse)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is useful for checking things later.
v2:
- fix hsw infoframe enabled check (Ander)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Add the missing PIPE_CONF_CHECK_I(has_infoframe); line to the
hw state cross-checker.]
[danet: Squash in fixup from Jesse to correctly compute has_infoframe
in the hdmi compute_config function.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will allow us to consult more info before deciding whether to flip
or do a full mode set.
v2:
- don't use uninitialized or incorrect pipe masks in set_config
failure path (Ander)
v3:
- fixup for pipe_config changes in compute_config (Jesse)
v4:
- drop spurious hunk in force restore path (Ander)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows us to calculate the full pipe config before we do any mode
setting work.
v2:
- clarify comments about global vs. per-crtc mode set (Ander)
- clean up unnecessary pipe_config = NULL setting (Ander)
v3:
- fix pipe_config handling (alloc in compute_config, free in set_mode) (Jesse)
- fix arg order in set_mode (Jesse)
- fix failure path of set_config (Ander)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the backlight device no longer gets registered too early we
should be able to drop most of the INVALID_PIPE checks from the backlight
code.
The only exceptio is the opregion stuff where we may (in theory at
least) get a request from the BIOS already during driver init as soon as
the backlight setup has been done. In which case we can still get the
INVALID_PIPE from intel_get_pipe_from_connector(). So leave that check
in place, and add a comment explaining why.
For the rest, if we still manage to get here with INVALID_PIPE on
VLV/CHV we will now get a WARN from the lower level functions and
can then actually investigate further.
v2: Leave the check in the BIOS related code (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we register the backlight device as soon as we register the
connector. That means we can get backlight requests from userspace
already before reading out the current modeset hardware state.
That means we don't yet know the current crtc->encoder->connector mapping,
which causes problems for VLV/CHV which need to know the current pipe in
order to figure out which BLC registers to poke. Currently we just
ignore such requests fairly deep in the backlight code which means the
backlight device brightness property will get out of sync with our
backlight.level and the actual hardware state.
Fix the problem by delaying the backlight device registration until the
entire modeset init has been performed. And we also move the
backlight unregisteration to happen as the first thing during the
modeset cleanup so that we also won't be bothered with userspace
backlight requested during teardown.
This is a real world problem on machines using systemd, because systemd,
for some reason, wants to restore the backlight to the level it used last
time. And that happens as soon as it sees the backlight device appearing
in the system. Sometimes the userspace access makes it through before
the modeset init, sometimes not.
v2: Do not lie to the user in the debug prints (Jani)
Include connector name in the prints (Jani)
Fix a typo in the commit message (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV both pipes A and B have their own backlight control
registers. In order to correctly read out the current hardware state at
init we need to know which pipe is driving the eDP port. Pass that
information down from the eDP init code into the backlight code.
To determine the correct pipe we first look at which pipe is currently
configured in the port control register, if that look invalid we look
at which pipe's PPS is currently controlling the port, and if that
too looks invalid we just assume pipe A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the connector would have an encoder but the encoder didn't have a
crtc we might dereference a NULL crtc here. I suppose that should never
happen due to intel_sanitize_encoder(), but let's be a bit paranoid
print a warning if we ever hit this and return INVALID_PIPE to the
caller.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV when the display is off, we can't read out the current
backlight level from the hardware since we have no pipe to do so.
Currently we end up reading a bigus register due to passing
INVALID_PIPE to VLV_BLC_PWM_CTL().
Skip the entire .get_backlight() call if the backlight isn't enabled
according to backlight.enabled.
This problem can be reproduced simply by reading the backlight device
actual_brightness file while the display is off.
Cc: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV/CHV have backlight controls only on pipes A and B. Bail out
without touching registers that don't exist, and print a warning.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently objects for which the hardware needs a contiguous physical
address are allocated a shadow backing storage to satisfy the contraint.
This shadow buffer is not wired into the normal obj->pages and so the
physical object is incoherent with accesses via the GPU, GTT and CPU. By
setting up the appropriate scatter-gather table, we can allow userspace
to access the physical object via either a GTT mmaping of or by rendering
into the GEM bo. However, keeping the CPU mmap of the shmemfs backing
storage coherent with the contiguous shadow is not yet possible.
Fortuituously, CPU mmaps of objects requiring physical addresses are not
expected to be coherent anyway.
This allows the physical constraint of the GEM object to be transparent
to userspace and allow it to efficiently render into or update them via
the GTT and GPU.
v2: Fix leak of pci handle spotted by Ville
v3: Remove the now duplicate call to detach_phys_object during free.
v4: Wait for rendering before pwrite. As this patch makes it possible to
render into the phys object, we should make it correct as well!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo noticed that we don't support RPS on GEN9 yet, so WARN for and
ignore any RPS interrupts on that platform.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The logical place for these functions is in i915_irq.c next to the rest of
PM interrupt handling functions.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The GEN6 and GEN8 versions differ only in the PM IIR and IER register
addresses and that on GEN8 we need to keep the
GEN8_PMINTR_REDIRECT_TO_NON_DISP PM interrupt unmasked. Abstract away
these 3 things in the GEN6 versions of the helpers and use them
everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the previous patch the GEN8 RPS handler became very similar to the
GEN6 version, so unify the two functions.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Move one misplaced hunk from a later patch to fix a bisect
issue as reported by Wu Fengguang's 0-day builder and fix suggested by
Imre.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The helpers to enable/disable PM IRQs for GEN6 and GEN8 are the same
except for the PM interrupt mask register, so abstract away this
register in the GEN6 versions and use these everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaDisablePartialInstShootdown:chv and
WaDisableThreadStallDopClockGating:chv are related to the same
register so combine them.
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-WaDisableDopClockGating:chv
-WaDisableSamplerPowerBypass:chv
-WaDisableGunitClockGating:chv
-WaDisableFfDopClockGating:chv
-WaDisableDopClockGating:chv
v2: Remove pre-production WA instead of restricting them
based on revision id (Ville)
For: VIZ-4090
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit "drm/i915: create a prepare phase for sprite plane updates"
changed the old_obj pointer we use when committing sprite planes,
which caused a WARN() and a BUG() to be triggered. Later, commit
"drm/i915: use intel_fb_obj() macros to assign gem objects" introduced
the same problem to function intel_commit_sprite_plane().
Regression introduced by:
commit ec82cb793c9224e0692eed904f43490cf70e8258
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Fri Oct 24 14:51:32 2014 +0100
drm/i915: create a prepare phase for sprite plane updates
and:
commit 77cde95217
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Fri Oct 24 14:51:33 2014 +0100
drm/i915: use intel_fb_obj() macros to assign gem objects
Credits to Imre Deak for pointing out the exact lines that were wrong.
v2: Also fix intel_commit_sprite_plane() (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85634
Testcase: igt/pm_rpm/legacy-planes
Testcase: igt/pm_rpm/legacy-planes-dpms
Testcase: igt/pm_rpm/universal-planes
Testcase: igt/pm_rpm/universal-planes-dpms
Credits-to: Imre Deak <imre.deak@intel.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- ppgtt init/release: these tracepoints are useful for observing the
creation and destruction of Full PPGTTs.
- ctx create/free: we can use the ctx_free trace in combination with the
ppgtt_release one to be sure that the ppgtt doesn't stay alive for too
long after the ctx is destroyed. ctx_create is there for simmetry
- switch_mm: important point in the lifetime of the vm
v4: add DOC information
v5: pull the DOC in drm.tmpl
v6: clean ppgtt init/release traces + add ctx create/free and switch_mm
tracepoints (Chris)
v7: drop execlist_submit_context tracepoint
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Baseline_ELD_Len field does not include ELD Header Block size.
From High Definition Audio Specification, Revision 1.0a:
The header block is a fixed size of 4 bytes. The baseline block
is variable size in multiple of 4 bytes, and its size is defined
in the header block Baseline_ELD_Len field (in number of
DWords).
Do not include the header size in Baseline_ELD_Len field. Fix all known
users of eld[2].
While at it, switch to DIV_ROUND_UP instead of open coding it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
[danvet: Fix compile fail in nouveau.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since a8bb681827 __intel_framebuffer_create() is called
with struct_mutex held, so it should use drm_gem_object_unreference()
instead of drm_gem_object_unreference_unlocked().
Found by Linux Driver Verification project (linuxtesting.org).
This regression has been introduced in
commit a8bb681827
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Feb 10 18:00:39 2014 +0100
drm/i915: Fix error path leak in fbdev fb allocation
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new pipe config values to calculate the updated pll dividers.
This regression was introduced in
commit 0dbdf89f27b17ae1eceed6782c2917f74cbb5d59
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Wed Oct 29 11:32:33 2014 +0200
drm/i915: Add infrastructure for choosing DPLLs before disabling crtcs
and
commit 00d958817dd3daaa452c221387ddaf23d1e4c06f
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Wed Oct 29 11:32:36 2014 +0200
drm/i915: Covert remaining platforms to choose DPLLS before disabling CRTCs
v2: Use intel_pipe_will_have_type() to look at new configuration - Ander
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
CC: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Creating a blob property will always copy the input data so the data
that is passed in can be const.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The cleanup path would reset pll->new_config to NULL but wouldn't free
the allocated memory.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turned out to be much simpler on top of my latest atomic stuff than
what I've feared. Some details:
- Drop the modeset_lock_all snakeoil in drm_plane_init. Same
justification as for the equivalent change in drm_crtc_init done in
commit d0fa1af40e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Sep 8 09:02:49 2014 +0200
drm: Drop modeset locking from crtc init function
Without these the drm_modeset_lock_init would fall over the exact
same way.
- Since the atomic core code wraps the locking switching it to
per-plane locks was a one-line change.
- For the legacy ioctls add a plane argument to the locking helper so
that we can grab the right plane lock (cursor or primary). Since the
universal cursor plane might not be there, or someone really crazy
might forgoe the primary plane even accept NULL.
- Add some locking WARN_ON to the atomic helpers for good paranoid
measure and to check that it all works out.
Tested on my exynos atomic hackfest with full lockdep checks and ww
backoff injection.
v2: I've forgotten about the load-detect code in i915.
v3: Thierry reported that in latest 3.18-rc vmwgfx doesn't compile any
more due to
commit 21e88620aa
Author: Rob Clark <robdclark@gmail.com>
Date: Thu Oct 30 13:39:04 2014 -0400
drm/vmwgfx: fix lock breakage
Rebased and fix this up.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUX/DqAAoJEHm+PkMAQRiGLtQH/iAt3fRHlYDXjaJian/KG1Cb
wVP0I+HWZmvVmmd0PzyaxCZLgRNwdmmYHEH4QLy2JwZ3jZfFHlxhy+hDWCgz+67t
bIzkLs0Pf1T4kJ2+r8qW2kBEz9PWJHGTQw7NTqZ++Ts3rPptBA6Fg4mEJ6fQigXy
qRIY68DpipUkXV9BWBWijnTmrvP5tt7JtPzBr4DC8frMjvWct8+XwYhc2k2tEv2j
LwLYb1OW6PUpPv2BQBfWjqqH77vYNQVhJwuwGcDe2YZdI0UFkDheL24+RbbPcZ4f
OnrLjJSSgzv6lBWkAaXZK7/WJ/JZbXxEqHzWZQ3xXoQov97bm7lEYJqqi5gDasQ=
=6Qpa
-----END PGP SIGNATURE-----
Merge tag 'v3.18-rc4' into drm-next
backmerge to get vmwgfx locking changes into next as the
conflict with per-plane locking.
As obj->map_and_fenceable computation has changed to only be set when
the object is bound inside the global GTT (and is suitable aligned to a
fence region) we need to accommodate those changes when the tiling is
adjusted. The easiest solution is to unbind from the global GTT if we
are currently fenceable, but will not be after the tiling change.
The bug has been exposed by
commit f8fcadba218fe6d23b2e353fea1cf0a4be4c9454
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Oct 31 13:53:52 2014 +0000
drm/i915: Only mark as map-and-fenceable when bound into the GGTT
which tried to fix an oversight from
commit e6a844687c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Aug 11 12:00:12 2014 +0200
drm/i915: Force CPU relocations if not GTT mapped
which changed the handling of obj->map_and_fenceable.
Note that the alignment check is a vestige from our attempts to reduce
the alignment requirements of tiled but unfenced buffers on
gen2/3. Also, that was when unbinding from the GTT meant UC writes and
clflushing, so we went to great pains to avoid such.
That leaves the actual bug of setting map_and_fenceable to true if we're
not bound to ggtt, which violates the change introduced in the above
patch. Unbinding in that case really looks like the simplest and safest
option, we have to do it anyway.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85896
Testcase: igt/gem_concurrent_blit/gttX*
Tested-by: huax.lu@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Valtteri Rantala <valtteri.rantala@intel.com>
[Jani: amend commit message per input from Daniel and bisect result from
Valtteri]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Backmerge drm-next so that I can keep merging patches. Specifically I
want:
- atomic stuff, yay!
- eld parsing patch from Jani.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We need the HPLL frequency when calculating cdclk. Currently we read
that out from the hardware every single time, which isn't going to fly
very well if the device is runtime suspended. So cache the HPLL
frequency in dev_priv and use the cached value.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 5cb13c07da.
While the relevance for WaRsDontPollForAckOnClearingFWBits is under
investigation, revert this as regression.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85684
Tested-by: Tested-by: lu hua <huax.lu@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: S, Deepak <deepak.s@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This simplifies the code quite a bit compared to iterating over all
rings during the ring interrupt.
Also, it allows us to drop the mmio_flip spinlock, since the mmio_flip
struct is only accessed in two places. The first is when the flip is
queued and the other when the mmio writes are done. Since a flip cannot
be queued while there is a pending flip, the two paths shouldn't ever
run in parallel. We might need to revisit that if support for replacing
flips is implemented though.
v2: Don't hold dev->struct_mutext while waiting (Chris)
v3: Make the wait uninterruptable (Chris)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So that it can be used by the flip code to wait for rendering without
holding any locks.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We may need to access various hardware bits in the .global_resources()
hook, so move the call to occur after enabling all the newly required
power wells, but before disabling all the now unneeded wells. This
should guarantee that we have all the sufficient hardware resources
available during the .global_resources() call. And if not, any additional
resources must be explicitly acquired by the .global_resorces() hook.
For instance on VLV/CHV we need to access the gunit mailbox so that we
can talk to punit/cck over sideband. In addition some PFI credit
reprogramming may need to be addes as well, which may require the disp2d
well.
This should also make the power domain refcounts consistent on platforms
which don't have a .global_resource() hook since now they too will
call modeset_update_crtc_power_domains() which will drop the init power.
Previously init power was just left enabled for such platforms.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: include the section in the drm docbook.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This not based on any documentation...
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As per spec, and similar to DDI.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for disabling the audio codec on vlv/chv/gen5-7, similar to
hsw/bdw.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to the hsw/bdw enable sequence rewrite.
v3: replace vblank wait with a comment
v4: expand the comment on what should be done with the vblank wait
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Configure and enable RC6 for Gen9.
v2: Rebase on top of BDW rc6 support (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Implement common forcewake functions shared by Gen9 features.
v2: Make the focewake_{get,put} functions static (Mika)
Small coding style fix in the function definition (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we write new values for the DDB allocation and WM parameters, we now
need to trigger the double buffer update for the pipe to take the new
configuration into account.
As the DDB is a global resource shared between planes, enabling or
disabling one plane will result in changes for all planes that are
currently in use, thus the need write PLANE_SURF/CUR_BASE for more than
the plane we're touching.
v2: Don't wait for pipes that are off
v3: Split the staging results structure to not exceed the 1Kb stack
allocation in skl_update_wm()
v4: Rework and document the algorithm after Ville found that it was all
wrong.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To correctly flush the new DDB allocation we need to know about the pipe
allocation layout inside the DDB in order to sequence the re-allocation
to not cause a newly allocated pipe to fetch from a space that was
previously allocated to another pipe.
This patch preserves the per-pipe (start,end) allocation to be used in
the flush.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can reduce the indentation level by continuing early.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The transition WMs code was doing a shortcut and the values were copied
from the WM0 ones at compute_wm_results() time. Going forward, we want
to compute them like the other WMs and resolve their final register
values in the same way as well.
This patch does just that and isolate the transtion WM compute code in
skl_compute_transition_wm() while skl_compute_wm_results() takes care of
the register values.
We also take the opportunity to disable the transition WMs for now.
We've noticed underruns and they seem to be the culprit.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DDB allocation code managed to split in two the compute functions.
Bring back skl_compute_transition_wm() and skl_compute_linetime_wm()
with their little friends.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To align with the ilk WM code and because it makes sense to test against
the upper bounds as soon as possible on variables that are bigger than
the number of bits in the register, let's move the maximum checks from
skl_compute_wm_results() to skl_compute_plane_wm().
v2: Leave the result values to 0 when overflowing the limits (Ville)
Use 32 bits intermediate variables (Damien)
Instead of using the 16 and 8 bits space we have in the result
structure, use 32 bits local variables until we're sure they fit into
the constraints.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
What we're talking about here is the DDB allocation (in blocks). That's
more descriptive than 'max_page_buff_alloc'.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville suggested that we should use the same semantics as C arrays to
reduce the number of those pesky +1/-1 in the allocation code.
This patch leaves the debugfs file as is, showing the internal DDB
allocation structure, not the values written in the registers.
v2: Remove the test on ->end in skl_ddb_entry_size() (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: minor conflict in i915_debugfs.c
v3: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument.
v4: minor conflict in the i915_debugfs_files array
v5: minor conflict in the i915_debugfs_files array
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Use the gen >= 9 in the debugfs file condition (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This logically belongs to the WM state, so do it there.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're going to add a new step, let's not hide the copy of the new WM
state inside one inner function, but as a 1st level operation in the WM
update.
v2: Split the staging results structure to not exceed the 1Kb stack
allocation in skl_update_wm()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to updated BSpec, If level 1 or any higher level has a value of 0x00,
that level and any higher levels are unused and the associated watermark
registers must not be enabled.
This patch checks for latency 0 for level >=1 and does not enable WM
corresponding to level m | m>=n, if level n (n != 0) has a 0us latency.
v2: Satheesh's review comments
- zero-out latency values (for all higher levels if latency of given
level is zero ) in read_wm_latency() function itself
v3: removed redundant check as per Satheesh's observation.
v4: rebase on top before merging (Damien)
v5: Rebase on top of the default value removal (Ville)
Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to the updated Bspec, The mailbox response data is not currently
accounting for memory read latency. Add 2 microseconds to the result for
each level.
This patch adds 2us to latency of level 0 for all cases and
for all other levels (1-7) only if latency[level] > 0.
v2: Slightly rework the patch and add a big comment (Damien)
v3: Rebase on top of the renames of the memory latency defines
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Reviewed-by: M, Satheeshakrishna <satheeshakrishna.m@intel.com> (v1)
Cc: Lespiau, Damien <damien.lespiau@intel.com>
Cc: M, Satheeshakrishna <satheeshakrishna.m@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch provides the implementation for reading the pipe wm HW
state.
v2: Incorporated Damien's review comments and also made modifications
to incorporate the plane/cursor split.
v3: No need to ident a line that was fitting 80 chars
Return early instead of indenting the remaining of a function
(Damien)
v4: Rebase on top of nightly (minor conflict in intel_drv.h)
v5: Rebase on top of nightly (minor conflict in intel_drv.h)
v6: Rebase on top of nightly (minor conflict in intel_drv.h)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Adapt to the planes/cursor split
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Fix the 3rd plane/cursor logic (Pradeep Bhat)
v3: Fix one-by-one error in the DDB allocation code
v4: Rebase on top of the skl_pipe_pixel_rate() argument change
v5: Replace the available/start/end output parameters of
skl_ddb_get_pipe_allocation_limits() by a single ddb entry constify
a few arguments
Make nth_active_pipe 0 indexed
Use sizeof(variable) instead of sizeof(type)
(Ville)
v6: Use the for_each_crtc() macro instead of list_for_each_entry()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tom O'Rourke