When a link is being established, the two endpoints advertise their
respective interface MTU in the transmitted RESET and ACTIVATE messages.
If there is any difference, the lower of the two MTUs will be selected
for use by both endpoints.
However, as a remnant of earlier attempts to introduce TIPC level
routing. there also exists an MTU discovery mechanism. If an intermediate
node has a lower MTU than the two endpoints, they will discover this
through a bisectional approach, and finally adopt this MTU for common use.
Since there is no TIPC level routing, and probably never will be,
this mechanism doesn't make any sense, and only serves to make the
link level protocol unecessarily complex.
In this commit, we eliminate the MTU discovery algorithm,and fall back
to the simple MTU advertising approach. This change is fully backwards
compatible.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bearer is disabled manually, all its links have to be reset
and deleted. However, if there is a remaining, parallel link ready
to take over a deleted link's traffic, we currently delay the delete
of the removed link until the failover procedure is finished. This
is because the remaining link needs to access state from the reset
link, such as the last received packet number, and any partially
reassembled buffer, in order to perform a successful failover.
In this commit, we do instead move the state data over to the new
link, so that it can fulfill the procedure autonomously, without
accessing any data on the old link. This means that we can now
proceed and delete all pertaining links immediately when a bearer
is disabled. This saves us from some unnecessary complexity in such
situations.
We also choose to change the confusing definitions CHANGEOVER_PROTOCOL,
ORIGINAL_MSG and DUPLICATE_MSG to the more descriptive TUNNEL_PROTOCOL,
FAILOVER_MSG and SYNCH_MSG respectively.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 8b4ed8634f
("tipc: eliminate race condition at dual link establishment")
we introduced a parallel link synchronization mechanism that
guarentees sequential delivery even for users switching from
an old to a newly established link. The new mechanism makes it
unnecessary to deliver the tunneled duplicate packets back to
the old link, as we are currently doing. It is now sufficient
to use the last tunneled packet's inner sequence number as
synchronization point between the two parallel links, whereafter
it can be dropped.
In this commit, we drop the duplicate packets arriving on the new
link, after updating the synchronization point at each new arrival.
Although it would now have been sufficient for the other endpoint
to only tunnel the last packet in its send queue, and not the
entire queue, we must still do this to maintain compatibility
with older nodes.
This commit makes it possible to get rid if some complex
interaction between the two parallel links.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
When remove TIPC module, there is a warning to remind us that a slab
object is leaked like:
root@localhost:~# rmmod tipc
[ 19.056226] =============================================================================
[ 19.057549] BUG TIPC (Not tainted): Objects remaining in TIPC on kmem_cache_close()
[ 19.058736] -----------------------------------------------------------------------------
[ 19.058736]
[ 19.060287] INFO: Slab 0xffffea0000519a00 objects=23 used=1 fp=0xffff880014668b00 flags=0x100000000004080
[ 19.061915] INFO: Object 0xffff880014668000 @offset=0
[ 19.062717] kmem_cache_destroy TIPC: Slab cache still has objects
This is because the listening socket of TIPC topology server is not
closed before TIPC proto handler is unregistered with proto_unregister().
However, as the socket is closed in tipc_exit_net() which is called by
unregister_pernet_subsys() during unregistering TIPC namespace operation,
the warning can be eliminated if calling unregister_pernet_subsys() is
moved before calling proto_unregister().
Fixes: e05b31f4bf ("tipc: make tipc socket support net namespace")
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A message sent to a node after a successful name table lookup may still
find that the destination socket has disappeared, because distribution
of name table updates is non-atomic. If so, the message will be rejected
back to the sender with error code TIPC_ERR_NO_PORT. If the source
socket of the message has disappeared in the meantime, the message
should be dropped.
However, in the currrent code, the message will instead be subject to an
unwanted tertiary lookup, because the function tipc_msg_lookup_dest()
doesn't check if there is an error code present in the message before
performing the lookup. In the worst case, the message may now find the
old destination again, and be redirected once more, instead of being
dropped directly as it should be.
A second bug in this function is that the "prev_node" field in the message
is not updated after successful lookup, something that may have
unpredictable consequences.
The problems arising from those bugs occur very infrequently.
The third change in this function; the test on msg_reroute_msg_cnt() is
purely cosmetic, reflecting that the returned value never can be negative.
This commit corrects the two bugs described above.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC node hash node table is protected with rcu lock on read side.
tipc_node_find() is used to look for a node object with node address
through iterating the hash node table. As the entire process of what
tipc_node_find() traverses the table is guarded with rcu read lock,
it's safe for us. However, when callers use the node object returned
by tipc_node_find(), there is no rcu read lock applied. Therefore,
this is absolutely unsafe for callers of tipc_node_find().
Now we introduce a reference counter for node structure. Before
tipc_node_find() returns node object to its caller, it first increases
the reference counter. Accordingly, after its caller used it up,
it decreases the counter again. This can prevent a node being used by
one thread from being freed by another thread.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Despite recent improvements, the establishment of dual parallel
links still has a small glitch where messages can bypass each
other. When the second link in a dual-link configuration is
established, part of the first link's traffic will be steered over
to the new link. Although we do have a mechanism to ensure that
packets sent before and after the establishment of the new link
arrive in sequence to the destination node, this is not enough.
The arriving messages will still be delivered upwards in different
threads, something entailing a risk of message disordering during
the transition phase.
To fix this, we introduce a synchronization mechanism between the
two parallel links, so that traffic arriving on the new link cannot
be added to its input queue until we are guaranteed that all
pre-establishment messages have been delivered on the old, parallel
link.
This problem seems to always have been around, but its occurrence is
so rare that it has not been noticed until recent intensive testing.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent changes in message importance handling it becomes
possible to simplify handling of messages and sockets when we
encounter link congestion.
We merge the function tipc_link_cong() into link_schedule_user(),
and simplify the code of the latter. The code should now be
easier to follow, especially regarding return codes and handling
of the message that caused the situation.
In case the scheduling function is unable to pre-allocate a wakeup
message buffer, it now returns -ENOBUFS, which is a more correct
code than the previously used -EHOSTUNREACH.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we only use a single counter; the length of the backlog
queue, to determine whether a message should be accepted to the queue
or not. Each time a message is being sent, the queue length is compared
to a threshold value for the message's importance priority. If the queue
length is beyond this threshold, the message is rejected. This algorithm
implies a risk of starvation of low importance senders during very high
load, because it may take a long time before the backlog queue has
decreased enough to accept a lower level message.
We now eliminate this risk by introducing a counter for each importance
priority. When a message is sent, we check only the queue level for that
particular message's priority. If that is ok, the message can be added
to the backlog, irrespective of the queue level for other priorities.
This way, each level is guaranteed a certain portion of the total
bandwidth, and any risk of starvation is eliminated.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a node joins a cluster while we are transmitting a fragment
stream over the broadcast link, it's missing the preceding fragments
needed to build a meaningful message. As a result, the node has to
drop it. However, as the fragment message is not acknowledged to
its sender before it's dropped, it accidentally causes link reset
of retransmission failure on the node.
Reported-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new bool automatic_shrinking to require the
user to explicitly opt-in to automatic shrinking of tables.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IPV6=m and TIPC=y, below error will appear during building kernel
image:
net/tipc/udp_media.c:196:
undefined reference to `ip6_dst_lookup'
make: *** [vmlinux] Error 1
As ip6_dst_lookup() is implemented in IPV6 and IPV6 is compiled as
module, ip6_dst_lookup() is not built-in core kernel image. As a
result, compiler cannot find 'ip6_dst_lookup' reference while
compiling TIPC code into core kernel image.
But with the method introduced by commit 5f81bd2e5d ("ipv6: export a
stub for IPv6 symbols used by vxlan"), we can avoid the compile error
through "ipv6_stub" pointer to access ip6_dst_lookup().
Fixes: d0f91938be ("tipc: add ip/udp media type")
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f2f8036 ("tipc: add support for connect() on dgram/rdm sockets")
hasn't validated user input length for the sockaddr structure which allows
a user to overwrite kernel memory with arbitrary input.
Fixes: f2f8036 ("tipc: add support for connect() on dgram/rdm sockets")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the explicit jhash value for the hashfn parameter
of rhashtable. The default is now jhash so removing the setting
makes no difference apart from making one less copy of jhash in
the kernel.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts tipc to the inlined rhashtable interface.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't directly call ipv6_sock_mc_join() but should use the stub
instead and protect it around IS_ENABLED.
Fixes: d0f91938be ("tipc: add ip/udp media type")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the example of ip4_datagram_connect, we store the
address in the socket structure for dgram/rdm sockets and use
that as the default destination for subsequent send() calls.
It is allowed to connect to any address types, and the behaviour
of send() will be the same as a normal sendto() with this address
provided. Binding to an AF_UNSPEC address clears the association.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 1186adf7df ("tipc: simplify message forwarding and
rejection in socket layer") -EHOSTUNREACH is propagated back to
the sending process if we fail to deliver the message to another
socket local to the node.
This is wrong, host unreachable should only be reported when the
destination port/name does not exist in the cluster, and that
check is always done before sending the message. Also, this
introduces inconsistent sendmsg() behavior for local/remote
destinations. Errors occurring on the receiving side should not
trickle up to the sender. If message delivery fails TIPC should
either discard the packet or reject it back to the sender based
on the destination droppable option.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_node_remove_conn may be called twice if shutdown() is
called on a socket that have messages in the receive queue.
Calling this function twice does no harm, but is unnecessary
and we remove the redundant call.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in favor of their inner __ ones, which doesn't grab rtnl.
As these functions need to operate on a locked socket, we can't be
grabbing rtnl by then. It's too late and doing so causes reversed
locking.
So this patch:
- move rtnl handling to callers instead while already fixing some
reversed locking situations, like on vxlan and ipvs code.
- renames __ ones to not have the __ mark:
__ip_mc_{join,leave}_group -> ip_mc_{join,leave}_group
__ipv6_sock_mc_{join,drop} -> ipv6_sock_mc_{join,drop}
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts tipc to use rhashtable max/min_size instead of
the obsolete max/min_shift.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIPC topology server is a per namespace service associated with the
tipc name {1, 1}. When a namespace is deleted, that name must be withdrawn
before we call sk_release_kernel because the kernel socket release is
done in init_net and trying to withdraw a TIPC name published in another
namespace will fail with an error as:
[ 170.093264] Unable to remove local publication
[ 170.093264] (type=1, lower=1, ref=2184244004, key=2184244005)
We fix this by breaking the association between the topology server name
and socket before calling sk_release_kernel.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the TIPC module is loaded, we launch a topology server in kernel
space, which in its turn is creating TIPC sockets for communication
with topology server users. Because both the socket's creator and
provider reside in the same module, it is necessary that the TIPC
module's reference count remains zero after the server is started and
the socket created; otherwise it becomes impossible to perform "rmmod"
even on an idle module.
Currently, we achieve this by defining a separate "tipc_proto_kern"
protocol struct, that is used only for kernel space socket allocations.
This structure has the "owner" field set to NULL, which restricts the
module reference count from being be bumped when sk_alloc() for local
sockets is called. Furthermore, we have defined three kernel-specific
functions, tipc_sock_create_local(), tipc_sock_release_local() and
tipc_sock_accept_local(), to avoid the module counter being modified
when module local sockets are created or deleted. This has worked well
until we introduced name space support.
However, after name space support was introduced, we have observed that
a reference count leak occurs, because the netns counter is not
decremented in tipc_sock_delete_local().
This commit remedies this problem. But instead of just modifying
tipc_sock_delete_local(), we eliminate the whole parallel socket
handling infrastructure, and start using the regular sk_create_kern(),
kernel_accept() and sk_release_kernel() calls. Since those functions
manipulate the module counter, we must now compensate for that by
explicitly decrementing the counter after module local sockets are
created, and increment it just before calling sk_release_kernel().
Fixes: a62fbccecd ("tipc: make subscriber server support net namespace")
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reported-by: Cong Wang <cwang@twopensource.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Messages transferred by TIPC are assigned an "importance priority", -an
integer value indicating how to treat the message when there is link or
destination socket congestion.
There is no separate header field for this value. Instead, the message
user values have been chosen in ascending order according to perceived
importance, so that the message user field can be used for this.
This is not a good solution. First, we have many more users than the
needed priority levels, so we end up with treating more priority
levels than necessary. Second, the user field cannot always
accurately reflect the priority of the message. E.g., a message
fragment packet should really have the priority of the enveloped
user data message, and not the priority of the MSG_FRAGMENTER user.
Until now, we have been working around this problem in different ways,
but it is now time to implement a consistent way of handling such
priorities, although still within the constraint that we cannot
allocate any more bits in the regular data message header for this.
In this commit, we define a new priority level, TIPC_SYSTEM_IMPORTANCE,
that will be the only one used apart from the four (lower) user data
levels. All non-data messages map down to this priority. Furthermore,
we take some free bits from the MSG_FRAGMENTER header and allocate
them to store the priority of the enveloped message. We then adjust
the functions msg_importance()/msg_set_importance() so that they
read/set the correct header fields depending on user type.
This small protocol change is fully compatible, because the code at
the receiving end of a link currently reads the importance level
only from user data messages, where there is no change.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct tipc_link contains one single queue for outgoing packets,
where both transmitted and waiting packets are queued.
This infrastructure is hard to maintain, because we need
to keep a number of fields to keep track of which packets are
sent or unsent, and the number of packets in each category.
A lot of code becomes simpler if we split this queue into a transmission
queue, where sent/unacknowledged packets are kept, and a backlog queue,
where we keep the not yet sent packets.
In this commit we do this separation.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unicast packet header contains a broadcast acknowledge sequence
number, that may need to be conveyed to the broadcast link for proper
treatment. Currently, the function tipc_rcv(), which is on the most
critical data path, calls the function tipc_bclink_acknowledge() to
have this done. This call is made for each received packet, and results
in the unconditional grabbing of the broadcast link spinlock.
This is unnecessary, since we can see directly from tipc_rcv() if
the acknowledged number differs from what has been previously acked
from the node in question. In the vast majority of cases the numbers
won't differ, and there is nothing to update.
We now make the call to tipc_bclink_acknowledge() conditional
to that the two ack values differ.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we currently extract a bundled buffer from a message bundle in
the function tipc_msg_extract(), we allocate a new buffer and explicitly
copy the linear data area.
This is unnecessary, since we can just clone the buffer and do
skb_pull() on the clone to move the data pointer to the correct
position.
This is what we do in this commit.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, TIPC linearizes all incoming buffers directly at reception
before passing them upwards in the stack. This is clearly a waste of
CPU resources, and must be avoided.
In this commit, we eliminate this unnecessary linearization. We still
ensure that at least the message header is linear, and that the buffer
is linearized where this is still needed, i.e. when unbundling and when
reversing messages.
In addition, we ensure that fragmented messages are validated after
reassembly before delivering them upwards in the stack.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function link_buf_validate() is in reality re-entrant and context
independent, and will in later commits be called from several locations.
Therefore, we move it to msg.c, make it outline and rename the it to
tipc_msg_validate().
We also redesign the function to make proper use of pskb_may_pull()
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIPC protocol spec has defined a 13 bit capability bitmap in
the neighbor discovery header, as a means to maintain compatibility
between different code and protocol generations. Until now this field
has been unused.
We now introduce the basic framework for exchanging capabilities
between nodes at first contact. After exchange, a peer node's
capabilities are stored as a 16 bit bitmap in struct tipc_node.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit afaa3f65f6
(tipc: purge links when bearer is disabled) was an attempt to resolve
a problem that turned out to have a more profound reason.
When we disable a bearer, we delete all its pertaining links if
there is no other bearer to perform failover to, or if the module
is shutting down. In case there are dual bearers, we wait with
deleting links until the failover procedure is finished.
However, this misses the case when a link on the removed bearer
was already down, so that there will be no failover procedure to
finish the link delete. This causes confusion if a new bearer is
added to replace the removed one, and also entails a small memory
leak.
This commit takes the current state of the link into account when
deciding when to delete it, and also reverses the above-mentioned
commit.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit c637c10355
("tipc: resolve race problem at unicast message reception") we
introduced a new mechanism for delivering buffers upwards from link
to socket layer.
That code contains a bug in how we handle the new link input queue
during failover. When a link is reset, some of its users may be blocked
because of congestion, and in order to resolve this, we add any pending
wakeup pseudo messages to the link's input queue, and deliver them to
the socket. This misses the case where the other, remaining link also
may have congested users. Currently, the owner node's reference to the
remaining link's input queue is unconditionally overwritten by the
reset link's input queue. This has the effect that wakeup events from
the remaining link may be unduely delayed (but not lost) for a
potentially long period.
We fix this by adding the pending events from the reset link to the
input queue that is currently referenced by the node, whichever one
it is.
This commit should be applied to both net and net-next.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9bbb4ecc68 ("tipc: standardize recvmsg routine") changed
the sleep/wakeup behaviour for sockets entering recv() or accept().
In this process the order of reporting -EAGAIN/-EINTR was reversed.
This caused problems with wrong errno being reported back if the
timeout expires. The same problem happens if the socket is
nonblocking and recv()/accept() is called when the process have
pending signals. If there is no pending data read or connections to
accept, -EINTR will be returned instead of -EAGAIN.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reported-by László Benedek <laszlo.benedek@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d0f91938be ("tipc: add ip/udp media type") introduced
some new sparse warnings. Clean them up.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip/udp bearer can be configured in a point-to-point
mode by specifying both local and remote ip/hostname,
or it can be enabled in multicast mode, where links are
established to all tipc nodes that have joined the same
multicast group. The multicast IP address is generated
based on the TIPC network ID, but can be overridden by
using another multicast address as remote ip.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The payload area following the TIPC discovery message header is an
opaque area defined by the media. INT_H_SIZE was enough for
Ethernet/IB/IPv4 but needs to be expanded to carry IPv6 addressing
information.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
After TIPC doesn't depend on iocb argument in its internal
implementations of sendmsg() and recvmsg() hooks defined in proto
structure, no any user is using iocb argument in them at all now.
Then we can drop the redundant iocb argument completely from kinds of
implementations of both sendmsg() and recvmsg() in the entire
networking stack.
Cc: Christoph Hellwig <hch@lst.de>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the iocb argument is used to idenfiy whether or not socket
lock is hold before tipc_sendmsg()/tipc_send_stream() is called. But
this usage prevents iocb argument from being dropped through sendmsg()
at socket common layer. Therefore, in the commit we introduce two new
functions called __tipc_sendmsg() and __tipc_send_stream(). When they
are invoked, it assumes that their callers have taken socket lock,
thereby avoiding the weird usage of iocb argument.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the exception of infiniband media which does not use media
offsets, the media address is always located at offset 4 in the
media info field as defined by the protocol, so we move the
definition to the generic bearer.h
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIPC_MEDIA_ADDR_SIZE and TIPC_MEDIA_ADDR_OFFSET names
are misleading, as they actually define the size and offset of
the whole media info field and not the address part. This patch
does not have any functional changes.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bearer is disabled by manual intervention, all links over that
bearer should be purged, indicated with the 'shutting_down' flag.
Otherwise tipc will get confused if a new bearer is enabled using
a different media type.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a subscription request is sent to a topology server
connection, and any error occurs (malformed request, oom
or limit reached) while processing this request, TIPC should
terminate the subscriber connection. While doing so, it tries
to access fields in an already freed (or never allocated)
subscription element leading to a nullpointer exception.
We fix this by removing the subscr_terminate function and
terminate the connection immediately upon any subscription
failure.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIPC name distributor pushes topology updates to the cluster
neighbors. Currently this is done in a unicast manner, and the
skb holding the update is cloned for each cluster member. This
is unnecessary, as we only modify the destnode field in the header
so we change it to do pskb_copy instead.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all real users of rhashtable default their grow and shrink
decision functions to rht_grow_above_75() and rht_shrink_below_30(),
so that there's currently no need to have this explicitly selectable.
It can/should be generic and private inside rhashtable until a real
use case pops up. Since we can make this private, we'll save us this
additional indirection layer and can improve insertion/deletion time
as well.
Reference: http://patchwork.ozlabs.org/patch/443040/
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_snprintf() was heavily utilized by the old netlink API which no
longer exists (now netlink compat).
In this patch we swap tipc_snprintf() to the identical scnprintf() in
the only remaining occurrence.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_CMD_NOOP to compat layer and remove the old framework.
All legacy nl commands are now converted to the compat layer in
netlink_compat.c.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_SHOW_STATS to compat layer. This command does not
have any counterpart in the new API, meaning it now solely exists as a
function in the compat layer.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_GET_NETID to compat dumpit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_SET_NETID to compat doit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_SET_NODE_ADDR to compat doit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_GET_NODES to compat dumpit and remove global node
counter solely used by the legacy API.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_GET_MEDIA_NAMES to compat dumpit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert socket (port) listing to compat dumpit call. If a socket
(port) has publications a second dumpit call is issued to collect them
and format then into the legacy buffer before continuing to process
the sockets (ports).
Command converted in this patch:
TIPC_CMD_SHOW_PORTS
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functionality for printing a dump header and convert
TIPC_CMD_SHOW_NAME_TABLE to compat dumpit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_RESET_LINK_STATS to compat doit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert setting of link proprieties to compat doit calls.
Commands converted in this patch:
TIPC_CMD_SET_LINK_TOL
TIPC_CMD_SET_LINK_PRI
TIPC_CMD_SET_LINK_WINDOW
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_GET_LINKS to compat dumpit and remove global link
counter solely used by the legacy API.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functionality for safely appending string data to a TLV without
keeping write count in the caller.
Convert TIPC_CMD_SHOW_LINK_STATS to compat dumpit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a framework for transcoding legacy nl action into actions
(.doit) calls from the new nl API. This is done by converting the
incoming TLV data into netlink data with nested netlink attributes.
Unfortunately due to the randomness of the legacy API we can't do this
generically so each legacy netlink command requires a specific
transcoding recipe. In this case for bearer enable and bearer disable.
Convert TIPC_CMD_ENABLE_BEARER and TIPC_CMD_DISABLE_BEARER into doit
compat calls.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a framework for dumping netlink data from the new netlink
API and formatting it to the old legacy API format. This is done by
looping the dump data and calling a format handler for each entity, in
this case a bearer.
We dump until either all data is dumped or we reach the limited buffer
size of the legacy API. Remember, the legacy API doesn't scale.
In this commit we convert TIPC_CMD_GET_BEARER_NAMES to use the compat
layer.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new netlink API is no longer "v2" but rather the standard API and
the legacy API is now "nl compat". We split them into separate
start/stop and put them in different files in order to further
distinguish them.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit c637c10355 ("tipc: resolve race
problem at unicast message reception") we introduced a time limit
for how long the function tipc_sk_eneque() would be allowed to execute
its loop. Unfortunately, the test for when this limit is passed was put
in the wrong place, resulting in a lost message when the test is true.
We fix this by moving the test to before we dequeue the next buffer
from the input queue.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a previous commit in this series we resolved a race problem during
unicast message reception.
Here, we resolve the same problem at multicast reception. We apply the
same technique: an input queue serializing the delivery of arriving
buffers. The main difference is that here we do it in two steps.
First, the broadcast link feeds arriving buffers into the tail of an
arrival queue, which head is consumed at the socket level, and where
destination lookup is performed. Second, if the lookup is successful,
the resulting buffer clones are fed into a second queue, the input
queue. This queue is consumed at reception in the socket just like
in the unicast case. Both queues are protected by the same lock, -the
one of the input queue.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure 'tipc_port_list' is used to collect port numbers
representing multicast destination socket on a receiving node.
The list is not based on a standard linked list, and is in reality
optimized for the uncommon case that there are more than one
multicast destinations per node. This makes the list handling
unecessarily complex, and as a consequence, even the socket
multicast reception becomes more complex.
In this commit, we replace 'tipc_port_list' with a new 'struct
tipc_plist', which is based on a standard list. We give the new
list stack (push/pop) semantics, someting that simplifies
the implementation of the function tipc_sk_mcast_rcv().
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new input message queue in struct tipc_link can be used for
delivering connection abort messages to subscribing sockets. This
makes it possible to simplify the code for such cases.
This commit removes the temporary list in tipc_node_unlock()
used for transforming abort subscriptions to messages. Instead, the
abort messages are now created at the moment of lost contact, and
then added to the last failed link's generic input queue for delivery
to the sockets concerned.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC handles message cardinality and sequencing at the link layer,
before passing messages upwards to the destination sockets. During the
upcall from link to socket no locks are held. It is therefore possible,
and we see it happen occasionally, that messages arriving in different
threads and delivered in sequence still bypass each other before they
reach the destination socket. This must not happen, since it violates
the sequentiality guarantee.
We solve this by adding a new input buffer queue to the link structure.
Arriving messages are added safely to the tail of that queue by the
link, while the head of the queue is consumed, also safely, by the
receiving socket. Sequentiality is secured per socket by only allowing
buffers to be dequeued inside the socket lock. Since there may be multiple
simultaneous readers of the queue, we use a 'filter' parameter to reduce
the risk that they peek the same buffer from the queue, hence also
reducing the risk of contention on the receiving socket locks.
This solves the sequentiality problem, and seems to cause no measurable
performance degradation.
A nice side effect of this change is that lock handling in the functions
tipc_rcv() and tipc_bcast_rcv() now becomes uniform, something that
will enable future simplifications of those functions.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list for outgoing traffic buffers from a socket is currently
allocated on the stack. This forces us to initialize the queue for
each sent message, something costing extra CPU cycles in the most
critical data path. Later in this series we will introduce a new
safe input buffer queue, something that would force us to initialize
even the spinlock of the outgoing queue. A closer analysis reveals
that the queue always is filled and emptied within the same lock_sock()
session. It is therefore safe to use a queue aggregated in the socket
itself for this purpose. Since there already exists a queue for this
in struct sock, sk_write_queue, we introduce use of that queue in
this commit.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_msg_eval() is in reality doing two related, but
different tasks. First it tries to find a new destination for named
messages, in case there was no first lookup, or if the first lookup
failed. Second, it does what its name suggests, evaluating the validity
of the message and its destination, and returning an appropriate error
code depending on the result.
This is confusing, and in this commit we choose to break it up into two
functions. A new function, tipc_msg_lookup_dest(), first attempts to find
a new destination, if the message is of the right type. If this lookup
fails, or if the message should not be subject to a second lookup, the
already existing tipc_msg_reverse() is called. This function performs
prepares the message for rejection, if applicable.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for enqueuing arriving buffers in the function tipc_sk_rcv()
contains long code lines and currently goes to two indentation levels.
As a cosmetic preparaton for the next commits, we break it out into
a separate function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Despite recent improvements, the handling of error codes and return
values at reception of messages in the socket layer is still confusing.
In this commit, we try to make it more comprehensible. First, we
separate between the return values coming from the functions called
by tipc_sk_rcv(), -those are TIPC specific error codes, and the
return values returned by tipc_sk_rcv() itself. Second, we don't
use the returned TIPC error code as indication for whether a buffer
should be forwarded/rejected or not; instead we use the buffer pointer
passed along with filter_msg(). This separation is necessary because
we sometimes want to forward messages even when there is no error
(i.e., protocol messages and successfully secondary looked up data
messages).
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The most common usage of namespace information is when we fetch the
own node addess from the net structure. This leads to a lot of
passing around of a parameter of type 'struct net *' between
functions just to make them able to obtain this address.
However, in many cases this is unnecessary. The own node address
is readily available as a member of both struct tipc_sock and
tipc_link, and can be fetched from there instead.
The fact that the vast majority of functions in socket.c and link.c
anyway are maintaining a pointer to their respective base structures
makes this option even more compelling.
In this commit, we introduce the inline functions tsk_own_node()
and link_own_node() to make it easy for functions to fetch the node
address from those structs instead of having to pass along and
dereference the namespace struct.
In particular, we make calls to the msg_xx() functions in msg.{h,c}
context independent by directly passing them the own node address
as parameter when needed. Those functions should be regarded as
leaves in the code dependency tree, and it is hence desirable to
keep them namspace unaware.
Apart from a potential positive effect on cache behavior, these
changes make it easier to introduce the changes that will follow
later in this series.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new link instance is created, it is trigged to start by
sending it a TIPC_STARTING_EVT, whereafter a regular link
reset is applied to it.
The starting event is codewise treated as a timeout event, and prompts
a link RESET message to be sent to the peer node, carrying a link
session identifier. The later link_reset() call nudges this session
identifier, whereafter all subsequent RESET messages will be sent out
with the new identifier. The latter session number overrides the former,
causing the peer to unconditionally accept it irrespective of its
current working state.
We don't think that this causes any problem, but it is not in accordance
with the protocol spec, and may cause confusion when debugging TIPC
sessions.
To avoid this, we make the starting event distinct from the
subsequent timeout events, by not allowing the former to send
out any RESET message. This eliminates the described problem.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instances of struct node are created in the function tipc_disc_rcv()
under the assumption that there is no race between received discovery
messages arriving from the same node. This assumption is wrong.
When we use more than one bearer, it is possible that discovery
messages from the same node arrive at the same moment, resulting in
creation of two instances of struct tipc_node. This may later cause
confusion during link establishment, and may result in one of the links
never becoming activated.
We fix this by making lookup and potential creation of nodes atomic.
Instead of first looking up the node, and in case of failure, create it,
we now start with looking up the node inside node_link_create(), and
return a reference to that one if found. Otherwise, we go ahead and
create the node as we did before.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During link failover it may happen that the remaining link goes
down while it is still in the process of taking over traffic
from a previously failed link. When this happens, we currently
abort the failover procedure and reset the first failed link to
non-failover mode, so that it will be ready to re-establish
contact with its peer when it comes available.
However, if the first link goes down because its bearer was manually
disabled, it is not enough to reset it; it must also be deleted;
which is supposed to happen when the failover procedure is finished.
Otherwise it will remain a zombie link: attached to the owner node
structure, in mode LINK_STOPPED, and permanently blocking any re-
establishing of the link to the peer via the interface in question.
We fix this by amending the failover abort procedure. Apart from
resetting the link to non-failover state, we test if the link is
also in LINK_STOPPED mode. If so, we delete it, using the conditional
tipc_link_delete() function introduced in the previous commit.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bearer is disabled, all pertaining links will be reset and
deleted. However, if there is a second active link towards a killed
link's destination, the delete has to be postponed until the failover
is finished. During this interval, we currently put the link in zombie
mode, i.e., we take it out of traffic, delete its timer, but leave it
attached to the owner node structure until all missing packets have
been received. When this is done, we detach the link from its node
and delete it, assuming that the synchronous timer deletion that was
initiated earlier in a different thread has finished.
This is unsafe, as the failover may finish before del_timer_sync()
has returned in the other thread.
We fix this by adding an atomic reference counter of type kref in
struct tipc_link. The counter keeps track of the references kept
to the link by the owner node and the timer. We then do a conditional
delete, based on the reference counter, both after the failover has
been finished and when the timer expires, if applicable. Whoever
comes last, will actually delete the link. This approach also implies
that we can make the deletion of the timer asynchronous.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one needs to copy the same data from user potentially more than
once. Sadly, MTU changes can trigger that ;-/
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If a large number of namespaces is spawned on a node and TIPC is
enabled in each of these, the excessive printk tracing of network
events will cause the system to grind down to a near halt.
The traces are still of debug value, so instead of removing them
completely we fix it by changing the link state and node availability
logging debug traces.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 07f6c4bc (tipc: convert tipc reference table to use generic
rhashtable) introduced a problem with port listing in the new netlink
API. It broke the resume functionality resulting in a never ending
loop. This was caused by starting with the first hash table every time
subsequently never returning an empty skb (terminating).
This patch fixes the resume mechanism by keeping a logical reference
to the last hash table along with a logical reference to the socket
(port) that didn't fit in the previous message.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f2f9800d49 "tipc: make tipc node table aware of net
namespace" has added a dereference of sock->sk before making sure it's
not NULL, which makes releasing a tipc socket NULL pointer dereference
for sockets that are not fully initialized.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the redundant timer defined in tipc_sock structure, instead we
can directly reuse the sk_timer defined in sock structure.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tipc module only allows users sitting on "init_net" namespace
to configure it through netlink interface. But now almost each tipc
component is able to be aware of net namespace, so it's time to open
the permission for users residing in other namespaces, allowing them
to configure their own tipc stack instance through netlink interface.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After namespace is supported, each namespace should own its private
random value. So the global variable representing the random value
must be moved to tipc_net structure.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC establishes one subscriber server which allows users to subscribe
their interesting name service status. After tipc supports namespace,
one dedicated tipc stack instance is created for each namespace, and
each instance can be deemed as one independent TIPC node. As a result,
subscriber server must be built for each namespace.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If net namespace is supported in tipc, each namespace will be treated
as a separate tipc node. Therefore, every namespace must own its
private tipc node address. This means the "tipc_own_addr" global
variable of node address must be moved to tipc_net structure to
satisfy the requirement. It's turned out that users also can assign
node address for every namespace.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC name table is used to store the mapping relationship between
TIPC service name and socket port ID. When tipc supports namespace,
it allows users to publish service names only owned by a certain
namespace. Therefore, every namespace must have its private name
table to prevent service names published to one namespace from being
contaminated by other service names in another namespace. Therefore,
The name table global variable (ie, nametbl) and its lock must be
moved to tipc_net structure, and a parameter of namespace must be
added for necessary functions so that they can obtain name table
variable defined in tipc_net structure.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now tipc socket table is statically allocated as a global variable.
Through it, we can look up one socket instance with port ID, insert
a new socket instance to the table, and delete a socket from the
table. But when tipc supports net namespace, each namespace must own
its specific socket table. So the global variable of socket table
must be redefined in tipc_net structure. As a concequence, a new
socket table will be allocated when a new namespace is created, and
a socket table will be deallocated when namespace is destroyed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC broadcast link is statically established and its relevant states
are maintained with the global variables: "bcbearer", "bclink" and
"bcl". Allowing different namespace to own different broadcast link
instances, these variables must be moved to tipc_net structure and
broadcast link instances would be allocated and initialized when
namespace is created.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bearer list defined as a global variable is used to store bearer
instances. When tipc supports net namespace, bearers created in
one namespace must be isolated with others allocated in other
namespaces, which requires us that the bearer list(bearer_list)
must be moved to tipc_net structure. As a result, a net namespace
pointer has to be passed to functions which access the bearer list.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Global variables associated with node table are below:
- node table list (node_htable)
- node hash table list (tipc_node_list)
- node table lock (node_list_lock)
- node number counter (tipc_num_nodes)
- node link number counter (tipc_num_links)
To make node table support namespace, above global variables must be
moved to tipc_net structure in order to keep secret for different
namespaces. As a consequence, these variables are allocated and
initialized when namespace is created, and deallocated when namespace
is destroyed. After the change, functions associated with these
variables have to utilize a namespace pointer to access them. So
adding namespace pointer as a parameter of these functions is the
major change made in the commit.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Involve namespace infrastructure, make the "tipc_net_id" global
variable aware of per namespace, and rename it to "net_id". In
order that the conversion can be successfully done, an instance
of networking namespace must be passed to relevant functions,
allowing them to access the "net_id" variable of per namespace.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make tipc socket table aware of namespace, a networking
namespace instance must be passed to tipc_sk_lookup(), allowing it
to look up tipc socket instance with a given port ID from a concrete
socket table. However, as now tipc_sk_timeout() only has one port ID
parameter and is not namespace aware, it's unable to obtain a correct
socket instance through tipc_sk_lookup() just with a port ID,
especially after namespace is completely supported.
If port ID is replaced with socket instance as tipc_sk_timeout()'s
parameter, it's unnecessary to look up socket table. But as the timer
handler - tipc_sk_timeout() is run asynchronously, socket reference
must be held before its timer is launched, and must be carefully
checked to identify whether the socket reference needs to be put or
not when its timer is terminated.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the works of initializing and shutting down tipc module are done
in core.h and core.c files, so all stuffs which are not closely
associated with the two tasks should be moved to appropriate places.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not only some wrapper function like k_term_timer() is empty, but also
some others including k_start_timer() and k_cancel_timer() don't return
back any value to its caller, what's more, there is no any component
in the kernel world to do such thing. Therefore, these timer interfaces
defined in tipc module should be purged.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant wrapper functions like tipc_core_start() and
tipc_core_stop(), and directly move them to their callers, such
as tipc_init() and tipc_exit(), having us clearly know what are
really done in both initialization and deinitialzation functions.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 58dc55f256 ("tipc: use generic
SKB list APIs to manage link transmission queue") we replace all list
traversal loops with the macros skb_queue_walk() or
skb_queue_walk_safe(). While the previous loops were based on the
assumption that the list was NULL-terminated, the standard macros
stop when the iterator reaches the list head, which is non-NULL.
In the function bclink_retransmit_pkt() this macro replacement has
lead to a bug. When we receive a BCAST STATE_MSG we unconditionally
call the function bclink_retransmit_pkt(), whether there really is
anything to retransmit or not, assuming that the sequence number
comparisons will lead to the correct behavior. However, if the
transmission queue is empty, or if there are no eligible buffers in
the transmission queue, we will by mistake pass the list head pointer
to the function tipc_link_retransmit(). Since the list head is not a
valid sk_buff, this leads to a crash.
In this commit we fix this by only calling tipc_link_retransmit()
if we actually found eligible buffers in the transmission queue.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As tipc reference table is statically allocated, its memory size
requested on stack initialization stage is quite big even if the
maximum port number is just restricted to 8191 currently, however,
the number already becomes insufficient in practice. But if the
maximum ports is allowed to its theory value - 2^32, its consumed
memory size will reach a ridiculously unacceptable value. Apart from
this, heavy tipc users spend a considerable amount of time in
tipc_sk_get() due to the read-lock on ref_table_lock.
If tipc reference table is converted with generic rhashtable, above
mentioned both disadvantages would be resolved respectively: making
use of the new resizable hash table can avoid locking on the lookup;
smaller memory size is required at initial stage, for example, 256
hash bucket slots are requested at the beginning phase instead of
allocating the entire 8191 slots in old mode. The hash table will
grow if entries exceeds 75% of table size up to a total table size
of 1M, and it will automatically shrink if usage falls below 30%,
but the minimum table size is allowed down to 256.
Also converts ref_table_lock to a separate mutex to protect hash table
mutations on write side. Lastly defers the release of the socket
reference using call_rcu() to allow using an RCU read-side protected
call to rhashtable_lookup().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Erik Hugne <erik.hugne@ericsson.com>
Cc: Thomas Graf <tgraf@suug.ch>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
net/tipc/link.c:1924:40: warning: Using plain integer as NULL pointer
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 908344cdda ("tipc: fix bug in multicast congestion handling")
introduced a race in the broadcast link wakeup functionality.
This patch eliminates this broadcast link wakeup race caused by
operation on the wakeup list without proper locking. If this race
hit and corrupted the list all subsequent wakeup messages would be
lost, resulting in a considerable memory leak.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit fb9962f3ce ("tipc: ensure all name sequences are properly
protected with its lock") involves below errors:
net/tipc/name_table.c:980 tipc_purge_publications() error: double lock 'spin_lock:&seq->lock'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that the code _using_ ->msg_iter at that point will be very
unhappy with anything other than unshifted iovec-backed iov_iter.
We still need to convert users to proper primitives.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
commit 908344cdda ("tipc: fix bug in multicast congestion
handling") introduced two bugs with the bclink wakeup
function. This commit fixes the missing spinlock init for the
waiting_sks list. We also eliminate the race condition
between the waiting_sks length check/dequeue operations in
tipc_bclink_wakeup_users by simply removing the redundant
length check.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Tero Aho <Tero.Aho@coriant.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of the old remote management feature is a piece of code
that checked permissions on the local system to see if a certain
operation was permitted, and if so pass the command to a remote
node. This serves no purpose after the removal of remote management
with commit 5902385a24 ("tipc: obsolete the remote management
feature") so we remove it.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert tipc name table read-write lock to RCU. After this change,
a new spin lock is used to protect name table on write side while
RCU is applied on read side.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a list_head variable is seen as a new entry to be added to a
list head, it's unnecessary to be initialized with INIT_LIST_HEAD().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tipc name sequence is published, name table lock is released
before name sequence buffer is delivered to remote nodes through its
underlying unicast links. However, when name sequence is withdrawn,
the name table lock is held until the transmission of the removal
message of name sequence is finished. During the process, node lock
is nested in name table lock. To prevent node lock from being nested
in name table lock, while withdrawing name, we should adopt the same
locking policy of publishing name sequence: name table lock should
be released before message is sent.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As tipc_nametbl_lock is used to protect name_table structure, the lock
must be held while all members of name_table structure are accessed.
However, the lock is not obtained while a member of name_table
structure - local_publ_count is read in tipc_nametbl_publish(), as
a consequence, an inconsistent value of local_publ_count might be got.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC internally created a name table which is used to store name
sequences. Now there is a read-write lock - tipc_nametbl_lock to
protect the table, and each name sequence saved in the table is
protected with its private lock. When a name sequence is inserted
or removed to or from the table, its members might need to change.
Therefore, in normal case, the two locks must be held while TIPC
operates the table. However, there are still several places where
we only hold tipc_nametbl_lock without proprerly obtaining name
sequence lock, which might cause the corruption of name sequence.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As TIPC subscriber server is terminated before name table, no user
depends on subscription list of name sequence when name table is
stopped. Therefore, all name sequences stored in name table should
be released whatever their subscriptions lists are empty or not,
otherwise, memory leak might happen.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name table locking policy is going to be adjusted from read-write
lock protection to RCU lock protection in the future commits. But
its essential precondition is to convert the allocation way of name
table from static to dynamic mode.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size variable is introduced in publ_list struct to help us exactly
calculate SKB buffer sizes needed by publications when all publications
in name table are delivered in bulk in named_distribute(). But if
publication SKB buffer size is assumed to MTU, the size variable in
publ_list struct can be completely eliminated at the cost of wasting
a bit memory space for last SKB.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Tero Aho <tero.aho@coriant.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard SKB list APIs associated with struct sk_buff_head to
manage socket outgoing packet chain and name table outgoing packet
chain, having relevant code simpler and more readable.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard SKB list APIs associated with struct sk_buff_head to
manage link's receive queue to simplify its relevant code cemplexity.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard SKB list APIs associated with struct sk_buff_head to
manage link's deferred queue, simplifying relevant code.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard SKB list APIs associated with struct sk_buff_head to
manage link transmission queue, having relevant code more clean.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pseudo message types of BUNDLE_CLOSED as well as BUNDLE_OPEN are
used to flag whether or not more messages can be bundled into a data
packet in the outgoing transmission queue. Obviously, no more messages
can be appended after the packet has been sent and is waiting to be
acknowledged and deleted. These message types do in reality represent
a send-side local implementation flag, and are not defined as part of
the protocol. It is therefore safe to move it to to where it belongs,
that is, the control area (TIPC_SKB_CB) of the buffer.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original tipc_link_push_packet(), it pushes messages from protocol
message queue, retransmission queue and next_out queue. But as the two
first queues are removed, we can simplify its relevant code through
deleting tipc_link_push_queue().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC retransmission queue is intended to record which messages
should be retransmitted when bearer is not congested. However,
as the retransmission queue becomes useless with the removal of
bearer congestion mechanism, it should be removed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC protocol message queue is intended to save one protocol message
when bearer is congested so that the message stored in the queue can
be immediately transmitted when bearer congestion is released. However,
as now the protocol queue has no mission any more with the removal of
bearer congestion mechanism, it should be removed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The node subscribe infrastructure represents a virtual base class, so
its users, such as struct tipc_port and struct publication, can derive
its implemented functionalities. However, after the removal of struct
tipc_port, struct publication is left as its only single user now. So
defining an abstract infrastructure for one user becomes no longer
reasonable. If corresponding new functions associated with the
infrastructure are moved to name_table.c file, the node subscription
infrastructure can be removed as well.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings about non-static declaration of static functions
in the new tipc netlink API.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NAME_TABLE_GET command to the new tipc netlink API.
This command supports dumping the name table of all nodes.
Netlink logical layout of name table response message:
-> name table
-> publication
-> type
-> lower
-> upper
-> scope
-> node
-> ref
-> key
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NET_SET command to the new tipc netlink API.
This command can set the network id and network (tipc) address.
Netlink logical layout of network set message:
-> net
[ -> id ]
[ -> address ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NET_GET command to the new tipc netlink API.
This command dumps the network id of the node.
Netlink logical layout of returned network data:
-> net
-> id
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NODE_GET to the new tipc netlink API.
This command can dump the address and node status of all nodes in the
tipc cluster.
Netlink logical layout of returned node/address data:
-> node
-> address
-> up flag
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_MEDIA_SET command to the new tipc netlink API.
This command can set one or more link properties for a particular
media.
Netlink logical layout of bearer set message:
-> media
-> name
-> link properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_MEDIA_GET command to the new tipc netlink API.
This command supports dumping all information about all defined
media as well as getting all information about a specific media.
The information about a media includes name and link properties.
Netlink logical layout of media get response message:
-> media
-> name
-> link properties
-> tolerance
-> priority
-> window
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_LINK_RESET_STATS command to the new netlink API.
This command resets the link statistics for a particular link.
Netlink logical layout of link reset message:
-> link
-> name
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_LINK_SET to the new tipc netlink API.
This command can set one or more link properties for a particular
link.
Netlink logical layout of link set message:
-> link
-> name
-> properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_LINK_GET command to the new tipc netlink API.
This command supports dumping all information about all links
(including the broadcast link) or getting all information about a
specific link (not the broadcast link).
The information about a link includes name, transmission info,
properties and link statistics.
As the tipc broadcast link is special we unfortunately have to treat
it specially. It is a deliberate decision not to abstract the
broadcast link on this (API) level.
Netlink logical layout of link response message:
-> port
-> name
-> MTU
-> RX
-> TX
-> up flag
-> active flag
-> properties
-> priority
-> tolerance
-> window
-> statistics
-> rx_info
-> rx_fragments
-> rx_fragmented
-> rx_bundles
-> rx_bundled
-> tx_info
-> tx_fragments
-> tx_fragmented
-> tx_bundles
-> tx_bundled
-> msg_prof_tot
-> msg_len_cnt
-> msg_len_tot
-> msg_len_p0
-> msg_len_p1
-> msg_len_p2
-> msg_len_p3
-> msg_len_p4
-> msg_len_p5
-> msg_len_p6
-> rx_states
-> rx_probes
-> rx_nacks
-> rx_deferred
-> tx_states
-> tx_probes
-> tx_nacks
-> tx_acks
-> retransmitted
-> duplicates
-> link_congs
-> max_queue
-> avg_queue
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_PUBL_GET command to the new tipc netlink API.
This command supports dumping of all publications for a specific
socket.
Netlink logical layout of request message:
-> socket
-> reference
Netlink logical layout of response message:
-> publication
-> type
-> lower
-> upper
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_SOCK_GET command to the new tipc netlink API.
This command supports dumping of all available sockets with their
associated connection or publication(s). It could be extended to reply
with a single socket if the NLM_F_DUMP isn't set.
The information about a socket includes reference, address, connection
information / publication information.
Netlink logical layout of response message:
-> socket
-> reference
-> address
[
-> connection
-> node
-> socket
[
-> connected flag
-> type
-> instance
]
]
[
-> publication flag
]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_BEARER_SET command to the new tipc netlink API.
This command can set one or more link properties for a particular
bearer.
Netlink logical layout of bearer set message:
-> bearer
-> name
-> link properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_BEARER_GET command to the new tipc netlink API.
This command supports dumping all data about all bearers or getting
all information about a specific bearer.
The information about a bearer includes name, link priorities and
domain.
Netlink logical layout of bearer get message:
-> bearer
-> name
Netlink logical layout of returned bearer information:
-> bearer
-> name
-> link properties
-> priority
-> tolerance
-> window
-> domain
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new netlink API for tipc that can disable or enable a tipc bearer.
The new API is separated from the old API because of a bug in the
user space client (tipc-config). The problem is that older versions
of tipc-config has a very low receive limit and adding commands to
the legacy genl_opts struct causes the ctrl_getfamily() response
message to grow, subsequently breaking the tool.
The new API utilizes netlink policies for input validation. Where the
top-level netlink attributes are tipc-logical entities, like bearer.
The top level entities then contain nested attributes. In this case
a name, nested link properties and a domain.
Netlink commands implemented in this patch:
TIPC_NL_BEARER_ENABLE
TIPC_NL_BEARER_DISABLE
Netlink logical layout of bearer enable message:
-> bearer
-> name
[ -> domain ]
[
-> properties
-> priority
]
Netlink logical layout of bearer disable message:
-> bearer
-> name
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to limit the amount of possible links to a
neighboring node to 2. If we have more then two bearers we can also
establish more links.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Reviewed-By: Jon Maloy <jon.maloy@ericsson.com>
cc: Ying Xue <ying.xue@windriver.com>
cc: Erik Hugne <erik.hugne@ericsson.com>
cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This encapsulates all of the skb_copy_datagram_iovec() callers
with call argument signature "skb, offset, msghdr->msg_iov, length".
When we move to iov_iters in the networking, the iov_iter object will
sit in the msghdr.
Having a helper like this means there will be less places to touch
during that transformation.
Based upon descriptions and patch from Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
Locking dependency detected below possible unsafe locking scenario:
CPU0 CPU1
T0: tipc_named_rcv() tipc_rcv()
T1: [grab nametble write lock]* [grab node lock]*
T2: tipc_update_nametbl() tipc_node_link_up()
T3: tipc_nodesub_subscribe() tipc_nametbl_publish()
T4: [grab node lock]* [grab nametble write lock]*
The opposite order of holding nametbl write lock and node lock on
above two different paths may result in a deadlock. If we move the
the updating of the name table after link state named out of node
lock, the reverse order of holding locks will be eliminated, and
as a result, the deadlock risk.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit ec8a2e5621 ("tipc: same receive
code path for connection protocol and data messages") we omitted the
the possiblilty that an arriving message extracted from a bundle buffer
may be a multicast message. Such messages need to be to be delivered to
the socket via a separate function, tipc_sk_mcast_rcv(). As a result,
small multicast messages arriving as members of a bundle buffer will be
silently dropped.
This commit corrects the error by considering this case in the function
tipc_link_bundle_rcv().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One aim of commit 50100a5e39 ("tipc:
use pseudo message to wake up sockets after link congestion") was
to handle link congestion abatement in a uniform way for both unicast
and multicast transmit. However, the latter doesn't work correctly,
and has been broken since the referenced commit was applied.
If a user now sends a burst of multicast messages that is big
enough to cause broadcast link congestion, it will be put to sleep,
and not be waked up when the congestion abates as it should be.
This has two reasons. First, the flag that is used, TIPC_WAKEUP_USERS,
is set correctly, but in the wrong field. Instead of setting it in the
'action_flags' field of the arrival node struct, it is by mistake set
in the dummy node struct that is owned by the broadcast link, where it
will never tested for. Second, we cannot use the same flag for waking
up unicast and multicast users, since the function tipc_node_unlock()
needs to pick the wakeup pseudo messages to deliver from different
queues. It must hence be able to distinguish between the two cases.
This commit solves this problem by adding a new flag
TIPC_WAKEUP_BCAST_USERS, and a new function tipc_bclink_wakeup_user().
The latter is to be called by tipc_node_unlock() when the named flag,
now set in the correct field, is encountered.
v2: using explicit 'unsigned int' declaration instead of 'uint', as
per comment from David Miller.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following sparse warnings:
sparse: symbol 'tipc_update_nametbl' was not declared. Should it be static?
Also, the function is changed to return bool upon success, rather than a
potentially freed pointer.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC name table updates are distributed asynchronously in a cluster,
entailing a risk of certain race conditions. E.g., if two nodes
simultaneously issue conflicting (overlapping) publications, this may
not be detected until both publications have reached a third node, in
which case one of the publications will be silently dropped on that
node. Hence, we end up with an inconsistent name table.
In most cases this conflict is just a temporary race, e.g., one
node is issuing a publication under the assumption that a previous,
conflicting, publication has already been withdrawn by the other node.
However, because of the (rtt related) distributed update delay, this
may not yet hold true on all nodes. The symptom of this failure is a
syslog message: "tipc: Cannot publish {%u,%u,%u}, overlap error".
In this commit we add a resiliency queue at the receiving end of
the name table distributor. When insertion of an arriving publication
fails, we retain it in this queue for a short amount of time, assuming
that another update will arrive very soon and clear the conflict. If so
happens, we insert the publication, otherwise we drop it.
The (configurable) retention value defaults to 2000 ms. Knowing from
experience that the situation described above is extremely rare, there
is no risk that the queue will accumulate any large number of items.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to perform the same actions when processing deferred name
table updates, so this functionality is moved to a separate
function.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6c9808ce09 ("tipc: remove port_lock") accidentally involves
a potential bug: when tipc socket instance(tsk) is not got with given
reference number in tipc_sk_get(), tsk is set to NULL. Subsequently
we jump to exit label where to decrease socket reference counter
pointed by tsk pointer in tipc_sk_put(). However, As now tsk is NULL,
oops may happen because of touching a NULL pointer.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We complete the merging of the port and socket layer by aggregating
the fields of struct tipc_port directly into struct tipc_sock, and
moving the combined structure into socket.c.
We also move all functions and macros that are not any longer
exposed to the rest of the stack into socket.c, and rename them
accordingly.
Despite the size of this commit, there are no functional changes.
We have only made such changes that are necessary due of the removal
of struct tipc_port.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reference table is now 'socket aware' instead of being generic,
and has in reality become a socket internal table. In order to be
able to minimize the API exposed by the socket layer towards the rest
of the stack, we now move the reference table definitions and functions
into the file socket.c, and rename the functions accordingly.
There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move the inline functions in the file port.h to socket.c, and modify
their names accordingly.
We move struct tipc_port and some macros to socket.h.
Finally, we remove the file port.h.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit, we move the remaining functions in port.c to
socket.c, and give them new names that correspond to their new
location. We then remove the file port.c.
There are only cosmetic changes to the moved functions.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In previous commits we have reduced usage of port_lock to a minimum,
and complemented it with usage of bh_lock_sock() at the remaining
locations. The purpose has been to remove this lock altogether, since
it largely duplicates the role of bh_lock_sock. We are now ready to do
this.
However, we still need to protect the BH callers from inadvertent
release of the socket while they hold a reference to it. We do this by
replacing port_lock by a combination of a rw-lock protecting the
reference table as such, and updating the socket reference counter while
the socket is referenced from BH. This technique is more standard and
comprehensible than the previous approach, and turns out to have a
positive effect on overall performance.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make tipc_sock the only entity referencable from other
parts of the stack, we add a tipc_sock pointer instead of a tipc_port
pointer to the registry. As a consequence, we also let the function
tipc_port_lock() return a pointer to a tipc_sock instead of a tipc_port.
We keep the function's name for now, since the lock still is owned by
the port.
This is another step in the direction of eliminating port_lock, replacing
its usage with lock_sock() and bh_lock_sock().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions tipc_port_get_ports() and tipc_port_reinit() scan over
all sockets/ports to access each of them. This is done by using a
dedicated linked list, 'tipc_socks' where all sockets are members. The
list is in turn protected by a spinlock, 'port_list_lock', while each
socket is locked by using port_lock at the moment of access.
In order to reduce complexity and risk of deadlock, we want to get
rid of the linked list and the accompanying spinlock.
This is what we do in this commit. Instead of the linked list, we use
the port registry to scan across the sockets. We also add usage of
bh_lock_sock() inside the scope of port_lock in both functions, as a
preparation for the complete removal of port_lock.
Finally, we move the functions from port.c to socket.c, and rename them
to tipc_sk_sock_show() and tipc_sk_reinit() repectively.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the latest changes to the socket/port layer the existence of
the functions tipc_port_init() and tipc_port_destroy() cannot be
justified. They are both called only once, from tipc_sk_create() and
tipc_sk_delete() respectively, and their functionality can better be
merged into the latter two functions.
This also entails that all remaining references to port_lock now are
made from inside socket.c, something that will make it easier to remove
this lock.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_acknowledge() is a remnant from the obsolete native
API. Currently, it grabs port_lock, before building an acknowledge
message and sending it to the peer.
Since all access to socket members now is protected by the socket lock,
it has become unnecessary to grab port_lock here.
In this commit, we remove the usage of port_lock, simplify the
function, and move it to socket.c, renaming it to tipc_sk_send_ack().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_port_connect()/tipc_port_disconnect() are remnants of the obsolete
native API. Their only task is to grab port_lock and call the functions
__tipc_port_connect()/__tipc_port_disconnect() respectively, which will
perform the actual state change.
Since socket/port exection now is single-threaded the use of port_lock
is not needed any more, so we can safely replace the two functions with
their lock-free counterparts.
In this commit, we remove the two functions. Furthermore, the contents
of __tipc_port_disconnect() is so trivial that we choose to eliminate
that function too, expanding its functionality into tipc_shutdown().
__tipc_port_connect() is simplified, moved to socket.c, and given the
more correct name tipc_sk_finish_conn(). Finally, we eliminate the
function auto_connect(), and expand its contents into filter_connect().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_port_shutdown() is a remnant from the now obsolete native
interface. As such it grabs port_lock in order to protect itself
from concurrent BH processing.
However, after the recent changes to the port/socket upcalls, sockets
are now basically single-threaded, and all execution, except the read-only
tipc_sk_timer(), is executing within the protection of lock_sock(). So
the use of port_lock is not needed here.
In this commit we eliminate the whole function, and merge it into its
only caller, tipc_shutdown().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last remaining BH upcall to the socket, apart for the message
reception function tipc_sk_rcv(), is the timer function.
We prefer to let this function continue executing in BH, since it only
does read-acces to semi-permanent data, but we make three changes to it:
1) We introduce a bh_lock_sock()/bh_unlock_sock() inside the scope
of port_lock. This is a preparation for replacing port_lock with
bh_lock_sock() at the locations where it is still used.
2) We move the function from port.c to socket.c, as a further step
of eliminating the port code level altogether.
3) We let it make use of the newly introduced tipc_msg_create()
function. This enables us to get rid of three context specific
functions (port_create_self_abort_msg() etc.) in port.c
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implementation, each 'struct tipc_node' instance keeps
a linked list of those ports/sockets that are connected to the node
represented by that struct. The purpose of this is to let the node
object know which sockets to alert when it loses contact with its peer
node, i.e., which sockets need to have their connections aborted.
This entails an unwanted direct reference from the node structure
back to the port/socket structure, and a need to grab port_lock
when we have to make an upcall to the port. We want to get rid of
this unecessary BH entry point into the socket, and also eliminate
its use of port_lock.
In this commit, we instead let the node struct keep list of "connected
socket" structs, which each represents a connected socket, but is
allocated independently by the node at the moment of connection. If
the node loses contact with its peer node, the list is traversed, and
a "connection abort" message is created for each entry in the list. The
message is sent to it respective connected socket using the ordinary
data path, and the receiving socket aborts its connections upon reception
of the message.
This enables us to get rid of the direct reference from 'struct node' to
´struct port', and another unwanted BH access point to the latter.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current link implementation keeps a linked list of blocked ports/
sockets that is populated when there is link congestion. The purpose
of this is to let the link know which users to wake up when the
congestion abates.
This adds unnecessary complexity to the data structure and the code,
since it forces us to involve the link each time we want to delete
a socket. It also forces us to grab the spinlock port_lock within
the scope of node_lock. We want to get rid of this direct dependence,
as well as the deadlock hazard resulting from the usage of port_lock.
In this commit, we instead let the link keep list of a "wakeup" pseudo
messages for use in such situations. Those messages are sent to the
pending sockets via the ordinary message reception path, and wake up
the socket's owner when they are received.
This enables us to get rid of the 'waiting_ports' linked lists in struct
tipc_port that manifest this direct reference. As a consequence, we can
eliminate another BH entry into the socket, and hence the need to grab
port_lock. This is a further step in our effort to remove port_lock
altogether.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_msg_init() has turned out to be of limited value
in many cases. It take too few parameters to be usable for creating
a complete message, it makes too many assumptions about what the
message should be used for, and it does not allocate any buffer to
be returned to the caller.
Therefore, we now introduce the new function tipc_msg_create(), which
takes all the parameters needed to create a full message, and returns
a buffer of the requested size. The new function will be very useful
for the changes we will be doing in later commits in this series.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3b4f302d85 ("tipc: eliminate
redundant locking") introduced a bug by removing the sanity check
for message importance, allowing programs to assign any value to
the msg_user field. This will mess up the packet reception logic
and may cause random link resets.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per comment from David Miller, we try to make the buffer reassembly
function more resilient to user errors than it is today.
- We check that the "*buf" parameter always is set, since this is
mandatory input.
- We ensure that *buf->next always is set to NULL before linking in
the buffer, instead of relying of the caller to have done this.
- We ensure that the "tail" pointer in the head buffer's control
block is initialized to NULL when the first fragment arrives.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
net/tipc/socket.c:545:5: warning:
symbol 'tipc_sk_proto_rcv' was not declared. Should it be static?
net/tipc/socket.c:2015:5: warning:
symbol 'tipc_ioctl' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we run broadcast packets over dual bearers/interfaces, the
current transmission code is flipping bearers between each sent
packet, with the purpose of leveraging the double bandwidth
available. The receiving bclink is resequencing the packets if
needed, so all messages are delivered upwards from the broadcast
link in the correct order, even if they may arrive in concurrent
interrupts.
However, at the moment of delivery upwards to the socket, we release
all spinlocks (bclink_lock, node_lock), so it is still possible
that arriving messages bypass each other before they reach the socket
queue.
We fix this by applying the same technique we are using for unicast
traffic. We use a link selector (i.e., the last bit of sending port
number) to ensure that messages from the same sender socket always are
sent over the same bearer. This guarantees sequential delivery between
socket pairs, which is sufficient to satisfy the protocol spec, as well
as all known user requirements.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous commit, we can now give the functions with temporary
names, such as tipc_link_xmit2(), tipc_msg_build2() etc., their proper
names.
There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now remove a number of functions which have become obsolete
and unreferenced through this commit series. There are no functional
changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit, we convert the socket multicast send function to
directly call the new multicast/broadcast function (tipc_bclink_xmit2())
introduced in the previous commit. We do this instead of letting the
call go via the now obsolete tipc_port_mcast_xmit(), hence saving
a call level and some code complexity.
We also remove the initial destination lookup at the message sending
side, and replace that with an unconditional lookup at the receiving
side, including on the sending node itself. This makes the destination
lookup and message transfer more uniform than before.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add a new broadcast link transmit function in bclink.c and a new
receive function in socket.c. The purpose is to move the branching
between external and internal destination down to the link layer,
just as we have done with unicast in earlier commits. We also make
use of the new link-independent fragmentation support that was
introduced in an earlier commit series.
This gives a shorter and simpler code path, and makes it possible
to obtain copy-free buffer delivery to all node local destination
sockets.
The new transmission code is added in parallel with the existing one,
and will be used by the socket multicast send function in the next
commit in this series.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We convert the link internal users (changeover protocol, broadcast
synchronization) to use the new packet send function.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a previous commit series ("tipc: new unicast transmission code")
we introduced a new message sending function, tipc_link_xmit2(),
and moved the unicast data users over to use that function. We now
let the internal name table distributor do the same.
The interaction between the name distributor and the node/link
layer also becomes significantly simpler, so we can eliminate
the function tipc_link_names_xmit().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the 'next' pointer of the last fragment buffer in a message is not
zeroed before reassembly, we risk ending up with a corrupt message,
since the reassembly function itself isn't doing this.
Currently, when a buffer is retrieved from the deferred queue of the
broadcast link, the next pointer is not cleared, with the result as
described above.
This commit corrects this, and thereby fixes a bug that may occur when
long broadcast messages are transmitted across dual interfaces. The bug
has been present since 40ba3cdf54 ("tipc:
message reassembly using fragment chain")
This commit should be applied to both net and net-next.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression bug caused by:
067608e9d0 ("tipc: introduce direct
iovec to buffer chain fragmentation function")
If data is sent on a nonblocking socket and the destination link
is congested, the buffer chain is leaked. We fix this by freeing
the chain in this case.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 37e22164a8 ("tipc: rename and
move message reassembly function") reassembly of long broadcast messages
has been broken. This is because we test for a non-NULL return value
of the *buf parameter as criteria for succesful reassembly. However, this
parameter is left defined even after reception of the first fragment,
when reassebly is still incomplete. This leads to a kernel crash as soon
as a the first fragment of a long broadcast message is received.
We fix this with this commit, by implementing a stricter behavior of the
function and its return values.
This commit should be applied to both net and net-next.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link state acks triggered from the receive path is done before
the last received packet have been processed by the link layer.
The effect of this is that the last received packet will not be
included in the ack. This causes problems if the link window is
set to TIPC_MIN_LINK_WIN, where the ack interval will be equal to
the link tolerance, and the link enters a stop-and-go behavior.
We move the ack logic to after link state processing, just before
the packet is delivered to higher layers.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Carl Sigurjonsson <carl.sigurjonsson@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic change, separating message delivery from the
link state processing.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a consequence of the recently introduced serialized access
to the socket in commit 8d94168a761819d10252bab1f8de6d7b202c3baa
("tipc: same receive code path for connection protocol and data
messages") we can make a number of simplifications in the
detection and handling of connection congestion situations.
- We don't need to keep two counters, one for sent messages and one
for acked messages. There is no longer any risk for races between
acknowledge messages arriving in BH and data message sending
running in user context. So we merge this into one counter,
'sent_unacked', which is incremented at sending and subtracted
from at acknowledge reception.
- We don't need to set the 'congested' field in tipc_port to
true before we sent the message, and clear it when sending
is successful. (As a matter of fact, it was never necessary;
the field was set in link_schedule_port() before any wakeup
could arrive anyway.)
- We keep the conditions for link congestion and connection connection
congestion separated. There would otherwise be a risk that an arriving
acknowledge message may wake up a user sleeping because of link
congestion.
- We can simplify reception of acknowledge messages.
We also make some cosmetic/structural changes:
- We rename the 'congested' field to the more correct 'link_cong´.
- We rename 'conn_unacked' to 'rcv_unacked'
- We move the above mentioned fields from struct tipc_port to
struct tipc_sock.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simplify the code for receiving connection probes, leveraging the
recently introduced tipc_msg_reverse() function. We also stick to
the principle of sending a possible response message directly from
the calling (tipc_sk_rcv or backlog_rcv) functions, hence making
the call chain shallower and easier to follow.
We make one small protocol change here, allowed according to
the spec. If a protocol message arrives from a remote socket that
is not the one we are connected to, we are currently generating a
connection abort message and send it to the source. This behavior
is unnecessary, and might even be a security risk, so instead we
now choose to only ignore the message. The consequnce for the sender
is that he will need longer time to discover his mistake (until the
next timeout), but this is an extreme corner case, and may happen
anyway under other circumstances, so we deem this change acceptable.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation to eliminate port_lock we need to bring reception
of connection protocol messages under proper protection of bh_lock_sock
or socket owner.
We fix this by letting those messages follow the same code path as
incoming data messages.
As a side effect of this change, the last reference to the function
net_route_msg() disappears, and we can eliminate that function.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several functions in port.c, related to the port protocol and
connection shutdown, need to send messages. We now convert them
to use the new link send function.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move the message sending across established connections
to use the message preparation and send functions introduced
earlier in this series. We now do the message preparation
and call to the link send function directly from the socket,
instead of going via the port layer.
As a consequence of this change, the functions tipc_send(),
tipc_port_iovec_rcv(), tipc_port_iovec_reject() and tipc_reject_msg()
become unreferenced and can be eliminated from port.c. For the same
reason, the functions tipc_link_xmit_fast(), tipc_link_iovec_xmit_long()
and tipc_link_iovec_fast() can be eliminated from link.c.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We merge the code for sending port name and port identity addressed
messages into the corresponding send functions in socket.c, and start
using the new fragmenting and transmit functions we just have introduced.
This saves a call level and quite a few code lines, as well as making
this part of the code easier to follow. As a consequence, the functions
tipc_send2name() and tipc_send2port() in port.c can be removed.
For practical reasons, we break out the code for sending multicast messages
from tipc_sendmsg() and move it into a separate function, tipc_sendmcast(),
but we do not yet convert it into using the new build/send functions.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a message arrives in a node and finds no destination
socket, we may need to drop it, reject it, or forward it after
a secondary destination lookup. The latter two cases currently
results in a code path that is perceived as complex, because it
follows a deep call chain via obscure functions such as
net_route_named_msg() and net_route_msg().
We now introduce a function, tipc_msg_eval(), that takes the
decision about whether such a message should be rejected or
forwarded, but leaves it to the caller to actually perform
the indicated action.
If the decision is 'reject', it is still the task of the recently
introduced function tipc_msg_reverse() to take the final decision
about whether the message is rejectable or not. In the latter case
it drops the message.
As a result of this change, we can finally eliminate the function
net_route_named_msg(), and hence become independent of net_route_msg().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way we build and send rejected message is currenty perceived as
hard to follow, partly because we let the transmission go via deep
call chains through functions such as tipc_reject_msg() and
net_route_msg().
We want to remove those functions, and make the call sequences shallower
and simpler. For this purpose, we separate building and sending of
rejected messages. We build the reject message using the new function
tipc_msg_reverse(), and let the transmission go via the newly introduced
tipc_link_xmit2() function, as all transmission eventually will do. We
also ensure that all calls to tipc_link_xmit2() are made outside
port_lock/bh_lock_sock.
Finally, we replace all calls to tipc_reject_msg() with the two new
calls at all locations in the code that we want to keep. The remaining
calls are made from code that we are planning to remove, along with
tipc_reject_msg() itself.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fragmentation at message sending is currently performed in two
places in link.c, depending on whether data to be transmitted
is delivered in the form of an iovec or as a big sk_buff. Those
functions are also tightly entangled with the send functions
that are using them.
We now introduce a re-entrant, standalone function, tipc_msg_build2(),
that builds a packet chain directly from an iovec. Each fragment is
sized according to the MTU value given by the caller, and is prepended
with a correctly built fragment header, when needed. The function is
independent from who is calling and where the chain will be delivered,
as long as the caller is able to indicate a correct MTU.
The function is tested, but not called by anybody yet. Since it is
incompatible with the existing tipc_msg_build(), and we cannot yet
remove that function, we have given it a temporary name.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Message fragmentation is currently performed at link level, inside
the protection of node_lock. This potentially binds up the sending
link structure for a long time, instead of letting it do other tasks,
such as handle reception of new packets.
In this commit, we make the MTUs of each active link become easily
accessible from the socket level, i.e., without taking any spinlock
or dereferencing the target link pointer. This way, we make it possible
to perform fragmentation in the sending socket, before sending the
whole fragment chain to the link for transport.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current link implementation provides several different transmit
functions, depending on the characteristics of the message to be
sent: if it is an iovec or an sk_buff, if it needs fragmentation or
not, if the caller holds the node_lock or not. The permutation of
these options gives us an unwanted amount of unnecessarily complex
code.
As a first step towards simplifying the send path for all messages,
we introduce two new send functions at link level, tipc_link_xmit2()
and __tipc_link_xmit2(). The former looks up a link to the message
destination, and if one is found, it grabs the node lock and calls
the second function, which works exclusively inside the node lock
protection. If no link is found, and the destination is on the same
node, it delivers the message directly to the local destination
socket.
The new functions take a buffer chain where all packet headers are
already prepared, and the correct MTU has been used. These two
functions will later replace all other link-level transmit functions.
The functions are not backwards compatible, so we have added them
as new functions with temporary names. They are tested, but have no
users yet. Those will be added later in this series.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some places, TIPC functions returns positive integers as return
codes. This goes against standard Linux coding practice, and may
even cause problems in some cases.
We now change the return values of the functions filter_rcv()
and filter_connect() to become signed integers, and return
negative error codes when needed. The codes we use in these
particular cases are still TIPC specific, since they are both
part of the TIPC API and have no correspondence in errno.h
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function tipc_nodesub_notify() we call a function pointer
aggregated into the object to be notified, whereafter we set
the function pointer to NULL. However, in some cases the function
pointed to will free the struct containing the function pointer,
resulting in a write to already freed memory.
This bug seems to always have been there, without causing any
notable harm.
In this commit we fix the problem by inverting the order of the
zeroing and the function call.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several instances where a pskb_copy or __pskb_copy is
immediately followed by an skb_clone.
Add a couple of new functions to allow the copy skb to be allocated
from the fclone cache and thus speed up subsequent skb_clone calls.
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 4f4482dcd9 ("tipc: compensate
for double accounting in socket rcv buffer") we access 'truesize' of
a received buffer after it might have been released by the function
filter_rcv().
In this commit we correct this by reading the value of 'truesize' to
the stack before delivering the buffer to filter_rcv().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it may then take longer than what the user specified using
setsockopt(SO_RCVTIMEO).
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to reduce complexity and save a call level during message
reception at port/socket level, we remove the function tipc_port_rcv()
and merge its functionality into tipc_sk_rcv().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_disc_rcv(), which is handling received neighbor
discovery messages, is perceived as messy, and it is hard to verify
its correctness by code inspection. The fact that the task it is set
to resolve is fairly complex does not make the situation better.
In this commit we try to take a more systematic approach to the
problem. We define a decision machine which takes three state flags
as input, and produces three action flags as output. We then walk
through all permutations of the state flags, and for each of them we
describe verbally what is going on, plus that we set zero or more of
the action flags. The action flags indicate what should be done once
the decision machine has finished its job, while the last part of the
function deals with performing those actions.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC currently handles two media specific addresses: Ethernet MAC
addresses and InfiniBand addresses. Those are kept in three different
formats:
1) A "raw" format as obtained from the device. This format is known
only by the media specific adapter code in eth_media.c and
ib_media.c.
2) A "generic" internal format, in the form of struct tipc_media_addr,
which can be referenced and passed around by the generic media-
unaware code.
3) A serialized version of the latter, to be conveyed in neighbor
discovery messages.
Conversion between the three formats can only be done by the media
specific code, so we have function pointers for this purpose in
struct tipc_media. Here, the media adapters can install their own
conversion functions at startup.
We now introduce a new such function, 'raw2addr()', whose purpose
is to convert from format 1 to format 2 above. We also try to as far
as possible uniform commenting, variable names and usage of these
functions, with the purpose of making them more comprehensible.
We can now also remove the function tipc_l2_media_addr_set(), whose
job is done better by the new function.
Finally, we expand the field for serialized addresses (format 3)
in discovery messages from 20 to 32 bytes. This is permitted
according to the spec, and reduces the risk of problems when we
add new media in the future.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_link_frag_rcv() is in reality a re-entrant generic
message reassemby function that has nothing in particular to do with
the link, where it is defined now. This becomes obvious when we see
the need to call the function from other places in the code.
In this commit rename it to tipc_buf_append() and move it to the file
msg.c. We also simplify its signature by moving the tail pointer to
the control block of the head buffer, hence making the head buffer
self-contained.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message reassembly function does not update the 'len' and 'data_len'
fields of the head skbuff correctly when fragments are chained to it.
This may sometimes lead to obsure errors, such as fragment reordering
when we receive fragments which are cloned buffers.
This commit fixes this, by ensuring that the two fields are updated
correctly.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, all incoming LINK_PROTOCOL messages, irrespective
of type, nudge the "last message received" checkpoint, informing the
link state machine that a message was received from the peer since last
supervision timeout event. This inhibits the link from starting probing
the peer unnecessarily.
However, not only STATE messages are recorded as legitimate incoming
traffic this way, but even RESET and ACTIVATE messages, which in
reality are there to inform the link that the peer endpoint has been
reset. At the same time, some RESET messages may be dropped instead
of causing a link reset. This happens when the link endpoint thinks
it is fully up and working, and the session number of the RESET is
lower than or equal to the current link session. In such cases the
RESET is perceived as a delayed remnant from an earlier session, or
the current one, and dropped.
Now, if a TIPC module is removed and then immediately reinserted, e.g.
when using a script, RESET messages may arrive at the peer link endpoint
before this one has had time to discover the failure. The RESET may be
dropped because of the session number, but only after it has been
recorded as a legitimate traffic event. Hence, the receiving link will
not start probing, and not discover that the peer endpoint is down, at
the same time ignoring the periodic RESET messages coming from that
endpoint. We have ended up in a stale state where a failed link cannot
be re-established.
In this commit, we remedy this by nudging the checkpoint only for
received STATE messages, not for RESET or ACTIVATE messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function net/core/sock.c::__release_sock() runs a tight loop
to move buffers from the socket backlog queue to the receive queue.
As a security measure, sk_backlog.len of the receiving socket
is not set to zero until after the loop is finished, i.e., until
the whole backlog queue has been transferred to the receive queue.
During this transfer, the data that has already been moved is counted
both in the backlog queue and the receive queue, hence giving an
incorrect picture of the available queue space for new arriving buffers.
This leads to unnecessary rejection of buffers by sk_add_backlog(),
which in TIPC leads to unnecessarily broken connections.
In this commit, we compensate for this double accounting by adding
a counter that keeps track of it. The function socket.c::backlog_rcv()
receives buffers one by one from __release_sock(), and adds them to the
socket receive queue. If the transfer is successful, it increases a new
atomic counter 'tipc_sock::dupl_rcvcnt' with 'truesize' of the
transferred buffer. If a new buffer arrives during this transfer and
finds the socket busy (owned), we attempt to add it to the backlog.
However, when sk_add_backlog() is called, we adjust the 'limit'
parameter with the value of the new counter, so that the risk of
inadvertent rejection is eliminated.
It should be noted that this change does not invalidate the original
purpose of zeroing 'sk_backlog.len' after the full transfer. We set an
upper limit for dupl_rcvcnt, so that if a 'wild' sender (i.e., one that
doesn't respect the send window) keeps pumping in buffers to
sk_add_backlog(), he will eventually reach an upper limit,
(2 x TIPC_CONN_OVERLOAD_LIMIT). After that, no messages can be added
to the backlog, and the connection will be broken. Ordinary, well-
behaved senders will never reach this buffer limit at all.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory overhead when allocating big buffers for data transfer may
be quite significant. E.g., truesize of a 64 KB buffer turns out
to be 132 KB, 2 x the requested size.
This invalidates the "worst case" calculation we have been
using to determine the default socket receive buffer limit,
which is based on the assumption that 1024x64KB = 67MB buffers
may be queued up on a socket.
Since TIPC connections cannot survive hitting the buffer limit,
we have to compensate for this overhead.
We do that in this commit by dividing the fix connection flow
control window from 1024 (2*512) messages to 512 (2*256). Since
older version nodes send out acks at 512 message intervals,
compatibility with such nodes is guaranteed, although performance
may be non-optimal in such cases.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Each node action flag should be set or cleared separately, instead
we now set the whole flags variable in one shot, and it's turned
out to be hard to see which other flags are affected. Therefore,
for instance, we explicitly clear TIPC_WAIT_OWN_LINKS_DOWN bit in
node_lost_contact().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename node flags to action_flags as well as its enum names so
that they can reflect its real meanings.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous commits of this series, we removed all asynchronous
actions which were based on the tasklet handler - "tipc_k_signal()".
So the moment has now come when we can completely remove the tasklet
handler infrastructure. That is done with this commit.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Postpone the actions of resetting all links until after bclink
lock is released, avoiding to asynchronously reset all links.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert allocations of global variables associated with bclink from
static way to dynamical way for the convenience of bclink instance
initialisation. Meanwhile, this also helps TIPC support name space
in the future easily.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we are going to do more jobs when bc_lock is released, the two
operations of holding/releasing the lock should be encapsulated with
functions. In addition, we move bc_lock spin lock into tipc_bclink
structure avoiding to define the global variable.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Postpone the actions of delivering name tables until after node
lock is released, avoiding to do it under asynchronous context.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since previously what all publications pertaining to the lost node
were removed from name table was finished in tasklet context
asynchronously, we need to TIPC_NAMES_GONE flag indicating whether
the node cleanup work is finished or not. But now as the cleanup work
has been finished when node lock is released, the flag becomes
meaningless for us.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Postpone the actions of notifying subscriptions until after node lock
is released, avoiding to asynchronously execute registered handlers
when node is lost.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename setup_blocked variable of node struct to a more common
name called "flags", which will be used to represent kinds of
node states.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move more frequently used variables up to the head of tipc_node
structure, hopefully improving a bit performance.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we obtain node lock with tipc_node_lock() in most time, there
are still places where we directly use native spin lock interface
to grab node lock. But as we will do more jobs in the future when node
lock is released, we should ensure that tipc_node_lock() is always
called when node lock is taken.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1bb8dce57f ("tipc: fix memory
leak during module removal") introduced a memory leak issue: when
name table is stopped, it's forgotten that publication instances are
freed properly. Additionally the useless "continue" statement in
tipc_nametbl_stop() is removed as well.
Reported-by: Jason <huzhijiang@gmail.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a89778d8ba ("tipc: add support
for link state subscriptions") introduced below possible deadlock
scenario:
CPU0 CPU1
T0: tipc_publish() link_timeout()
T1: tipc_nametbl_publish() [grab node lock]*
T2: [grab nametbl write lock]* link_state_event()
T3: named_cluster_distribute() link_activate()
T4: [grab node lock]* tipc_node_link_up()
T5: tipc_nametbl_publish()
T6: [grab nametble write lock]*
The opposite order of holding nametbl write lock and node lock on
above two different paths may result in a deadlock. If we move the
the delivery of named messages via link out of name nametbl lock,
the reverse order of holding locks will be eliminated, as a result,
the deadlock will be killed as well.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 78acb1f9b8 ("tipc: add
ioctl to fetch link names") introduced a buffer overflow bug where
specially crafted ioctl requests could cause out-of-bounds indexing
of the node->links array. This was caused by an incorrect check vs
MAX_BEARERS, and the static code checker complaint is:
net/tipc/node.c:459 tipc_node_get_linkname() error: buffer overflow 'node->links' 2 <= 2
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit a8b9b96e95 ("tipc: fix race
in disc create/delete") leads to the following static checker warning:
net/tipc/discover.c:352 tipc_disc_create()
warn: possible memory leak of 'req'
The risk of memory leak really exists in practice. Especially when
it's failed to allocate memory for "req->buf", tipc_disc_create()
doesn't free its allocated memory, instead just directly returns
with ENOMEM error code. In this situation, memory leak, of course,
happens.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add a new ioctl for AF_TIPC that can be used to fetch the
logical name for a link to a remote node on a given bearer. This
should be used in combination with link state subscriptions.
The logical name size limit definitions are moved to tipc.h, as
they are now also needed by the new ioctl.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When links are established over a bearer plane, we create a node
local publication containing information about the peer node and
bearer plane. This allows TIPC applications to use the standard
TIPC topology server subscription mechanism to get notifications
when a link goes up or down.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible by passing a netlink socket to a more privileged
executable and then to fool that executable into writing to the socket
data that happens to be valid netlink message to do something that
privileged executable did not intend to do.
To keep this from happening replace bare capable and ns_capable calls
with netlink_capable, netlink_net_calls and netlink_ns_capable calls.
Which act the same as the previous calls except they verify that the
opener of the socket had the desired permissions as well.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a21a584d67 (tipc: fix neighbor
detection problem after hw address change) introduces a race condition
involving tipc_disc_delete() and tipc_disc_add/remove_dest that can
cause TIPC to dereference the pointer to the bearer discovery request
structure after it has been freed since a stray pointer is left in the
bearer structure.
In order to fix the issue, the process of resetting the discovery
request handler is optimized: the discovery request handler and request
buffer are just reset instead of being freed, allocated and initialized.
As the request point is always valid and the request's lock is taken
while the request handler is reset, the race doesn't happen any more.
Reported-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The node map variable - 'nodes' in bearer structure is only used by
bclink. When bclink accesses it, bc_lock is held. But when change it,
for instance, in tipc_bearer_add_dest() or tipc_bearer_remove_dest()
the bc_lock is not taken at all. To avoid any inconsistent data, we
should always grab bc_lock while accessing node map variable.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As bearer pointer is known in tipc_l2_device_event(), it's unnecessary
to search it again in tipc_disable_bearer(). If tipc_disable_bearer()
is replaced with bearer_disable() in tipc_l2_device_event(), this will
help us save a bit time when bearer is disabled.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'media_ptr' pointer in bearer structure which points to network
device, is protected by RCU. So, before netdevice is released,
synchronize_net() should be involved to prevent no any user of
the netdevice on read side from accessing it after it is freed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now tipc routing hierarchy comprises the structures 'node', 'link'and
'bearer'. The whole hierarchy is protected by a big read/write lock,
tipc_net_lock, to ensure that nothing is added or removed while code
is accessing any of these structures. Obviously the locking policy
makes node, link and bearer components closely bound together so that
their relationship becomes unnecessarily complex. In the worst case,
such locking policy not only has a negative influence on performance,
but also it's prone to lead to deadlock occasionally.
In order o decouple the complex relationship between bearer and node
as well as link, the locking policy is adjusted as follows:
- Bearer level
RTNL lock is used on update side, and RCU is used on read side.
Meanwhile, all bearer instances including broadcast bearer are
saved into bearer_list array.
- Node and link level
All node instances are saved into two tipc_node_list and node_htable
lists. The two lists are protected by node_list_lock on write side,
and they are guarded with RCU lock on read side. All members in node
structure including link instances are protected by node spin lock.
- The relationship between bearer and node
When link accesses bearer, it first needs to find the bearer with
its bearer identity from the bearer_list array. When bearer accesses
node, it can iterate the node_htable hash list with the node
address to find the corresponding node.
In the new locking policy, every component has its private locking
solution and the relationship between bearer and node is very simple,
that is, they can find each other with node address or bearer identity
from node_htable hash list or bearer_list array.
Until now above all changes have been done, so tipc_net_lock can be
removed safely.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the media_ptr pointer is protected with tipc_net_lock write lock
on write side; tipc_net_lock read lock is used to read side. As the
part of effort of eliminating tipc_net_lock, we decide to adjust the
locking policy of media_ptr pointer protection: on write side, RTNL
lock is use while on read side RCU read lock is applied.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently on both paths of message transmission and reception, the
read lock of tipc_net_lock must be held before bearer is accessed,
while the write lock of tipc_net_lock has to be taken before bearer
is configured. Although it can ensure that bearer is always valid on
the two data paths, link and bearer is closely bound together.
So as the part of effort of removing tipc_net_lock, the locking
policy of bearer protection will be adjusted as below: on the two
data paths, RCU is used, and on the configuration path of bearer,
RTNL lock is applied.
Now RCU just covers the path of message reception. To make it possible
to protect the path of message transmission with RCU, link should not
use its stored bearer pointer to access bearer, but it should use the
bearer identity of its attached bearer as index to get bearer instance
from bearer_list array, which can help us decouple the relationship
between bearer and link. As a result, bearer on the path of message
transmission can be safely protected by RCU when we access bearer_list
array within RCU lock protection.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert bearer_list to RCU list. It's protected by RTNL lock on
update side, and RCU read lock is applied to read side.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the tipc network initialization(ie, tipc_net_start routine) is
under RTNL protection, its corresponding deinitialization part(ie,
tipc_net_stop routine) should be protected by RTNL too.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the 'tipc_ptr' pointer is protected by tipc_net_lock
write lock on write side, and RCU read lock is applied to read
side. In addition, there have two paths on write side where we
may change variables pointed by the 'tipc_ptr' pointer: one is
to configure bearer by tipc-config tool and another one is that
bearer status is changed by notification events of its attached
interface. But on the latter path, we improperly deem that
accessing 'tipc_ptr' pointer happens on read side with
rcu_read_lock() although some variables pointed by the 'tipc_ptr'
pointer are changed possibly.
Moreover, as now the both paths are guarded by RTNL lock, it's
better to adjust the locking policy of 'tipc_ptr' pointer
protection, allowing RTNL instead of tipc_net_lock write lock to
protect it on write side, which will help us purge tipc_net_lock
in the future.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have two paths where we can configure or change bearer status:
one is that bearer is configured from user space with tipc-config
tool; another one is that bearer is changed by notification events
from its attached interface. On the first path, one dedicated
config_mutex lock is guarded; on the latter path, RTNL lock has been
placed to serialize the process of dealing with interface events.
So, if RTNL lock is also used to protect the first path, this will
not only extremely help us simplify current locking policy, but also
config_mutex lock can be deleted as well.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several spots in the kernel perform a sequence like:
skb_queue_tail(&sk->s_receive_queue, skb);
sk->sk_data_ready(sk, skb->len);
But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up. So this skb->len access is potentially
to freed up memory.
Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.
And finally, no actual implementation of this callback actually uses
the length argument. And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.
So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.
Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: David S. Miller <davem@davemloft.net>
net/tipc/socket.c: In function ‘tipc_release’:
net/tipc/socket.c:352: warning: ‘res’ is used uninitialized in this function
Introduced by commit 24be34b5a0 ("tipc:
eliminate upcall function pointers between port and socket"), which
removed the sole initializer of "res".
Just return 0 to fix it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5902385a24 ("tipc: obsolete
the remote management feature") introduces a regression where node
topology events are not being generated because the publication
that triggers this: {0, <z.c.n>, <z.c.n>} is no longer available.
This will break applications that rely on node events to discover
when nodes join/leave a cluster.
We fix this by advertising the node publication when TIPC enters
networking mode, and withdraws it upon shutdown.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy