This patch separates the TCO bits from snd_hdspm_proc_read_madi(), so
the new function can later be shared between MADI and AES32 cards.
It's essentially only moving code around, no new functionality.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a left-over mistake from old code, the correct register offset is
provided in kcontrol->private_value, not in the index.
Cf. RayDAT case, where it has already been corrected.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AIO cards allow to use AEB (Analogue Expansion Boards) to add four
input and/or output channels.
This patch adds the necessary code to detect and enable the additional
I/O channels.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch uses the newly introduced HDSPM_CONTROL_TRISTATE functions to
create and expose the following ALSA controls:
- Gain selection for Input, Output and Phones (HiGain, +4dBu, -10dbV)
- S/PDIF Input select (Coaxial, Optical, Internal)
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AIO cards offer at least four individual settings options with three
states each. Those settings are represented as two bits in the settings
register with the following meaning:
0*some_base_bit --> Option value 0
1*some_base_bit --> Option value 1
2*some_base_bit --> Option value 2
3*some_base_bit --> mask to select the two involved bits
This patch adds a generic ALSA control macro for such a value-to-bit
pattern mapping. It will be used in a later commit to expose four new
controls.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ENUMERATED_CTL_INFO is a macro, so the binary code is generated multiple
times. To avoid code duplication, refactor the involved functionality
into a function and make ENUMERATED_CTL_INFO a call to this function.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds the following ALSA controls:
- S/PDIF Out Optical to switch S/PDIF Out from coaxial to optical
- S/PDIF Out Professional to send the Pro bit in the output stream
- ADAT-Internal to enable ADAT/TDIF Expansion Board (AEB/TEB)
- XLR Breakout Cable if analogue I/O uses the XLR breakout cable
- WCK48 to force WordClock to the 32-48kHz range (single speed) if
the card is operating at higher frequencies
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds new ALSA controls to send single-speed WordClock and
S/PDIF-Professional on RME RayDAT cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdspm_set_system_clock_mode() is almost a one-by-one copy of
hdspm_set_toggle_setting(). To improve code quality, remove the
duplication.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDSPM_TOGGLE_SETTING functions alter the control_register on older
cards. On newer cards (AIO/RayDAT), they have to operate on the
settings_register instead.
This patch augments the existing functions to work with AIO/RayDAT, too.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RME RayDAT and AIO cards are new designs with different register
settings. Since we need to distinguish them from older cards multiple
times in the driver, refactor the code into a separate helper function.
No functional change intended.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver did not support all possible configurations. These defines
will be used by later commits to add the missing functionality.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similarly to MADI, WordClock can also be at SingleSpeed while the card
is actually working at twice or four times this rate. If so, multiply
the base rate accordingly.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the DoubleSpeed or QuadSpeed bit is set, the SingleSpeed frequency
has to be multiplied accordingly. Since this functionality will be
required at least twice, refactor it into a separate function.
The second reference to the newly introduced hdspm_rate_multiplier()
will be in a separate commit.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As drvdata is cleared to NULL at probe failure or at removal by the
driver core, we don't have to call pci_set_drvdata(pci, NULL) any
longer in each driver.
The only remaining pci_set_drvdata(NULL) is in azx_firmware_cb() in
hda_intel.c. Since this function itself releases the card instance,
we need to clear drvdata here as well, so that it won't be released
doubly in the remove callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Expose the newly added TCO LTC and sync check functions to userspace.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds new ALSA controls to query the LTC state from userspace.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch prepares snd_hdspm_get_sync_check() to also check the TCO
sync state. The added feature will be exposed to the user in a later
commit.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Considerably shorten the code by using a macro. Though this won't lower
the binary size, it makes the source more readable.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For 96kHz, MADI allows to multiplex the samples (SMUX) or to use a
dedicated 96K mode. The RME cards default to 96K mode, but since not all
external MADI equipment supports this, provide a switch to users that
changes the on-wire protocol to SMUX.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When using the additional Time Code Option module in slave mode or the
SYNC-In wordclock connector, the sample rate needs to be returned by
hdspm_external_sample_rate().
Since this sample rate may contain any value with 1Hz granularity, we
need to round it to a common rate as done by the OSX driver.
[Fixed missing function declarations by tiwai]
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit introduces hdspm_get_pll_freq() to avoid code duplication.
Reading the sample rate from the DDS register will be required by
upcoming code.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With HDSP_TOGGLE_SETTING in place, these functions are no longer
required. Removing them makes the code DRY and considerably shorter.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDSP_TOGGLE_SETTING and its corresponding functions allow to change
settings in the control register. Instead of using the specialised
functions, use the generic code to make the code DRY.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver contains multiple similar functions that change only a single
bit in the control register, only the bit position varies.
This patch implements a generic function to toggle a certain bit
position that will be used to replace the old code.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current iobox detection code reportedly fails for various users, so
simply do what the Win32 driver does instead.
Patch originally by Karl Grill <kgrill@chello.at> and then modified to
comply with kernel coding guidelines + current HEAD.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use correct bitmask for AES32 cards to determine wordclock lock state,
add missing bitmask for sync check and make output of the corresponding
control and /proc coherent.
Signed-off-by: Andre Schramm <andre.schramm@iosono-sound.com>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With HDSPM_TOGGLE_SETTING in place, these functions are no longer
required. Removing them makes the code DRY and considerably shorter.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDSPM_TOGGLE_SETTING and its corresponding functions allow to change
settings in the control register. Instead of using the specialised
functions, use the generic code to make the code DRY.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver contains at least six similar functions that change only a
single bit in the control register, only the bit position varies.
This patch implements a generic function to toggle a certain bit
position that will be used to replace the old code.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the recent firmware code tries to reread and cache the firmware by
itself, it's even better to keep the struct firmware data instead of
keeping a local copy. Also, it makes little sense to disable the fw
loader for this driver, so added the explicit dependency, too.
Last, but not least, allocate the firmware data loaded via ioctl in
vmalloc'ed buffer instead, as the firmware size isn't that small.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The RayDAT reports the sync status of its inputs in consecutive bit
positions, so all we do in hdspm_s1_sync_check is to iterate over idx:
status = hdspm_read(hdspm, HDSPM_RD_STATUS_1);
lock = (status & (0x1<<idx)) ? 1 : 0;
sync = (status & (0x100<<idx)) ? 1 : 0;
The index is given in kcontrol->private_value:
HDSPM_SYNC_CHECK("WC SyncCheck", 0),
HDSPM_SYNC_CHECK("AES SyncCheck", 1),
HDSPM_SYNC_CHECK("SPDIF SyncCheck", 2),
HDSPM_SYNC_CHECK("ADAT1 SyncCheck", 3),
HDSPM_SYNC_CHECK("ADAT2 SyncCheck", 4),
HDSPM_SYNC_CHECK("ADAT3 SyncCheck", 5),
HDSPM_SYNC_CHECK("ADAT4 SyncCheck", 6),
HDSPM_SYNC_CHECK("TCO SyncCheck", 7),
HDSPM_SYNC_CHECK("SYNC IN SyncCheck", 8),
The patch corrects the indicated sync flags by passing the proper index
value to hdspm_s1_sync_check().
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
checkpatch.pl discourages the use of spaces at the beginning of lines.
Some of the CTL_ELEM defines were not properly indented.
This patch replaces the leading spaces by tabs. No functionality is
changed, the commit is purely cosmetic.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the documentation, AES32 cards use a different bit position
for reporting the sync_in status.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In contrast to AES32, MADI uses the first status register to report the
sync_in status.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MADI and MADIface used to report the autosync_sample_rate. This
functionality was lost in commit
0dca179306, this commit now adds it back.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Missing breaks lead to a fall-through, thus causing the wrong
autosync_sample_rate to be reported.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to missing breaks and the resulting fall-through, card subtype
selection was effectively missing, thus causing the wrong sync check
functions to be called.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a follow-up to a97bda7d29, report the
external sample rate as system_sample_rate when in slave mode.
For PCIe MADI cards, the DDS value automatically contains the external
sample rate, but the PCI version needs this manual workaround.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The DDS value is the actual physical sample rate. We set it indirectly
when selecting 44100, 48000 and so on via snd_hdspm_hw_params or
hdspm_set_clock_source.
This commit now allows the DDS value to be altered at runtime, thus
speeding up or slowing down the physical sample rate. This is required
for MADI's varispeed that allows for ±12.5% speed adjustment from the
"selected" rate (32kHz, 44100kHz, 48kHz and so on).
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On PCI RME MADI cards, the PLL register does not contain the proper
value, so the calculated system_sample_rate is wrong. In this case, we
simply return the cached rate from struct hdspm.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hdsp uses its own ioctls to acquire config- and status information.
Expose the corresponding ioctl handler via ioctl_compat, so that 32bit applications can use it on 64bit kernels.
Signed-off-by: Andre Schramm <andre.schramm@iosono-sound.com>
Reviewed-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hdspm uses its own ioctls to acquire config- and status information.
Expose the corresponding ioctl handler via ioctl_compat, so that 32bit
applications can use it on 64bit kernels.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Before, /proc/asound looked like this:
2 [Default ]: HDSPM - RME RayDAT_f1cd85
RME RayDAT S/N 0xf1cd85 at 0xf7300000, irq 18
In case of a second HDSPM card, its name would be Default_1. This is
cumbersome, because the order of the cards isn't stable across reboots.
To help userspace tools referring to the correct card, this commit
provides a unique id for each card:
2 [HDSPMxf1cd85 ]: HDSPM - RME RayDAT_f1cd85
RME RayDAT S/N 0xf1cd85 at 0xf7300000, irq 18
In this example, userspace (configuration files) would then use
hw:HDSPMxf1cd85 to choose the right card.
The serial is masked to 24bits, so this string is always shorter than
sixteen chars.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dan Carpenter reported that setting 0 to uinfo->value.enumerated.items
in snd_hdsp_info_pref_sync_ref() may lead to Oops. This function should
return an error immediately in such a case instead.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The serial number is used multiple times in hdspm.c. Since it belongs
to the card, let's store it in struct hdspm and refer to it whenever
necessary.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit c09403dcc5 has introduced a
regression: PCIe versions of RME MADI were no longer detected, because
the MADIface ID (0xd5) was used instead of the correct 0xd2.
This commit fixes the problem.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
The implicit presence of module.h lured several users into
incorrectly thinking that they only needed/used modparam.h
but once we clean up the module.h presence, these will show
up as build failures, so fix 'em now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
From the Windows INF file, we know the firmware ranges for all RME
cards. For PCIe, a single revision ID per device (RayDAT, MADI, AIO,
AES) is used. Contrary, the older PCI versions use ranges, that is,
one revision ID per firmware version.
Instead of listing all possible revisions individually, match the range.
This commit enables all MADI and AES PCI versions ever shipped.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDSP_VERSION_BIT has to be ORed with HDSP_S_LOAD. This fixes the detection
of at least some RME RPM boxes.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SNDRV_HDSPM_IOCTL_GET_STATUS is supposed to query the current card
status, so we have to return what we receive on the MADI wire (RX), not
what we transmit (TX) to others. The latter is a config item to be
queried via SNDRV_HDSPM_IOCTL_GET_CONFIG.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Smatch has a new check for Rosenberg type information leaks where
structs are copied to the user with uninitialized stack data in them.
The status struct has a hole in it, and on some paths not all the
members were initialized.
struct hdspm_status {
unsigned char card_type; /* 0 1 */
/* XXX 3 bytes hole, try to pack */
enum hdspm_syncsource autosync_source; /* 4 4 */
long long unsigned int card_clock; /* 8 8 */
The hdspm_version struct had holes in it as well.
struct hdspm_version {
unsigned char card_type; /* 0 1 */
char cardname[20]; /* 1 20 */
/* XXX 3 bytes hole, try to pack */
unsigned int serial; /* 24 4 */
short unsigned int firmware_rev; /* 28 2 */
/* XXX 2 bytes hole, try to pack */
int addons; /* 32 4 */
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Refactoring the code using snd_pcm_hw_constraint_pow2() helper function.
Tested-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AES32 supports the non-standard 128kHZ, and this is enabled only when
SNDRV_PCM_RATE_KNOT is set in hw.rates field.
Tested-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Newer RME cards like RayDAT and AIO support 32 samples per period. This
value is encoded as {1,1,1} in the HDSP_LatencyMask bits in the control
register.
Since {1,1,1} is also the representation for 8192 samples/period on
older RME cards, we have to special case 32 samples and 32768 bytes
according to the actual card.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, hdspm_decode_latency is called several times, violating the
DRY principle. Given that we need to distinguish between old and new
cards when decoding the latency bits in the control register, introduce
hdspm_get_latency() to provide the required functionality.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On newer RME cards like RayDAT and AIO, the 8192 samples per period size
are no longer supported. Instead, setting all three bits of
HDSP_LatencyMask to one ({1,1,1}) now corresponds to 32 samples per
period.
To make this more obvious to future developers, let's reorder the array
according to their bit representation, starting at 64 ({0,0,0}) up to
4096 ({1,1,0}) and finally 32 ({1,1,1}).
Note that this patch doesn't change semantics.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On newer RME cards like RayDAT and AIO, the lower bound is 32 samples
per period in contrast to 64 samples as seen on older cards.
We hence lower period_bytes_min to 32 * 4. Four bytes per sample.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Older RME cards like MADI and AES support period sizes of 8192 samples.
The original hdspm driver already featured this value, apparently, it
was lost during the rewrite.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put the exception checks for io_type switch() for possible mistakes in
future. Also this shuts up annoying compile warnings.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apparently, there are multiple old firmware revisions in the wild for
the PCI RME MADI cards. Just add them to the list of supported devices
and treat them like their modern counterparts.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In slave mode, the card can only detect the base frequency (32..48kHz)
on the MADI link (exception: 96k frames), so the real external sample
rate is this base frequency multiplied by 1, 2 or 4 depending on the
speed mode.
This patch enables 64..192kHz sample rates in clock slave mode, which
failed before due to an alleged sample rate mismatch between the MADI
link (e.g., 48kHz) and the application in DS/QS mode (e.g., 96kHz,
192kHz).
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When running in slave mode (no clock master), there is no way to
determine the real wirespeed on the MADI link (single/double/quad
speed). Like physical gear, simply provide the user with a tristate
switch to select the appropriate format.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The char can be unsigned on some architectures. Since the code checks
the negative values, they should be declared as signed char explicitly.
sound/pci/rme9652/hdspm.c:5449: warning: comparison is always false due to limited range of data type
sound/pci/rme9652/hdspm.c:5462: warning: comparison is always false due to limited range of data type
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI version of the RME HDSP MADI card uses 0xcf as revision ID. Just
add this to the list of supported cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When using Word Clock on RME MADI cards, AutoSync mode was alternating
betweeen MADI and WC due to a typo: AutoSync is indicated in the second
status register (status2), not the first one (status).
While the proc output was always correct, the reported WC frequency to
ALSA was unstable as mentioned in
http://mailman.alsa-project.org/pipermail/alsa-devel/2008-March/006723.html
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For the MIDI part, we need to acquire (and release) the hmidi->lock,
access to the global hdspm structure is serialized through
hmidi->hdspm->lock instead.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The name argument of request_irq() appears in /proc/interrupts, and
it's quite ugly when the name entry contains a space or special letters.
In general, it's simpler and more readable when the module name appears
there, so let's replace all entries with KBUILD_MODNAME.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The convention for pci_driver.name entry in kernel drivers seem to be
the module name or equivalent ones. But, so far, almost all PCI sound
drivers use more verbose name like "ABC Xyz (12)", and these are fairly
confusing when appearing as a file name.
This patch converts the all pci_driver.name entries in sound/pci/* to
use KBUILD_MODNAME for more unified appearance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current AES32 firmware revision ID is 234, however, a user confirmed
that everything works fine with the previous revision, too.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Depending on the model and the presence of a TCO module, the number of
midi ports varies. Some have 1 port (MADIface), some have 2 (default),
with TCO, there are 3.
Don't hardcode the number of midi ports to initialize.
This patch also fixes a boot lockup on MADIface.
[Coding-style fixes by tiwai]
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In contrast to the PCIe version (RME AES), the PCI version (RME AES32)
has a different firmware revision.
This patch adds the missing PCI revision.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Original patch by Dan Rosenberg <drosenberg@vsecurity.com> under commit
e68d3b316a. I'm copying his text here:
The SNDRV_HDSPM_IOCTL_GET_CONFIG_INFO ioctl in hdspm.c allow unprivileged
users to read uninitialized kernel stack memory, because several fields
of the hdspm_config struct declared on the stack are not altered
or zeroed before being copied back to the user. This patch takes care
of it.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fredrik Lingvall <fredrik.lingvall@gmail.com> has discovered wrong
frequency and sync detection on AES32. According to him, the provided
patch fixes these issues.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In contrast to the RME MADI card, coax/optical selection on the MADIface
is done via a physical switch located at the breakout box. Obviously,
the driver cannot switch ports in software.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Caused by two typos, no output channel mappings were assigned for
MADI/MADIface at double/quad speed.
The channel mapping is indeed identical to the single speed mapping, the
cards will simply use the first N channels.
Signed-off-by: Florian Faber <faber@faberman.de>
Signed-off-by: Fredrik Lingvall <fredrik.lingvall@gmail.com>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without calling an appropriate rule, AES/AES32 cards would announce a
theoretical channel count of 64 (HDSPM_MAX_CHANNELS), leading to the
already known bug:
[37422.640481] ------------[ cut here ]------------
[37422.640487] WARNING: at sound/pci/rme9652/hdspm.c:5449
snd_hdspm_ioctl+0x18f/0x202 [snd_hdspm]()
[37422.640489] Hardware name: PRIMERGY RX100 S6
[37422.640490] BUG? (info->channel >= hdspm->max_channels_in)
[37422.640492] Modules linked in: snd_hdspm snd_seq_midi ipmi_watchdog
ipmi_poweroff ipmi_si ipmi_devintf ipmi_msghandler i2c_i801 e1000e
snd_rawmidi power_meter [last unloaded: snd_hdspm]
[37422.640501] Pid: 22231, comm: jackd Tainted: G D W
2.6.36-gentoo-r5 #5
[37422.640502] Call Trace:
[37422.640508] [<ffffffff8103db3a>] warn_slowpath_common+0x80/0x98
[37422.640511] [<ffffffff8103dbe6>] warn_slowpath_fmt+0x41/0x43
[37422.640514] [<ffffffff81034306>] ? get_parent_ip+0x11/0x42
[37422.640518] [<ffffffffa0055763>] snd_hdspm_ioctl+0x18f/0x202
[snd_hdspm]
[37422.640522] [<ffffffff813fd626>] snd_pcm_channel_info+0x73/0x7c
[37422.640525] [<ffffffff814001e9>] snd_pcm_common_ioctl1+0x326/0xb01
[37422.640527] [<ffffffff81034306>] ? get_parent_ip+0x11/0x42
[37422.640531] [<ffffffff8105be6c>] ? __srcu_read_unlock+0x3b/0x59
[37422.640533] [<ffffffff81400bce>] snd_pcm_capture_ioctl1+0x20a/0x227
[37422.640537] [<ffffffff811e599c>] ? file_has_perm+0x90/0x9e
[37422.640540] [<ffffffff81400c15>] snd_pcm_capture_ioctl+0x2a/0x2e
[37422.640543] [<ffffffff810f2c69>] do_vfs_ioctl+0x404/0x453
[37422.640546] [<ffffffff810f2d09>] sys_ioctl+0x51/0x74
[37422.640549] [<ffffffff81002aab>] system_call_fastpath+0x16/0x1b
[37422.640552] ---[ end trace 0cd919cd68118082 ]---
We already have all the right values in place, we simply have to inform
the upper layers about this restriction.
Note that snd_hdspm_hw_rule_rate_out_channels and
snd_hdspm_hw_rule_rate_in_channels must not be called on AES32, because
the channel count is always 16, no matter of the samplerate in use.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only RayDAT and AIO provide sane buffer pointers that can be used with
HDSPM_BufferPositionMask, on all other cards, this would result in a
wrong HW pointer leading to xruns and these messages:
[260808.916788] BUG: pcmC0D0p:0, pos = 2976, buffer size = 1024, period size = 512
[260808.961124] BUG: pcmC0D0c:0, pos = 4944, buffer size = 1024, period size = 512
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As requested by Takashi and Jaroslav, these arrays should not be in the
header file.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Incorporate changes by Florian Faber into hdspm.c. Code taken from
http://wiki.linuxproaudio.org/index.php/Driver:hdspe
Heavily reworked to mostly comply with the coding standard (whitespace
fixes, line width, C++ style comments)
The code was tested and confirmed to be working on RME RayDAT.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the RME HDSP RPM IO box. Changes have been made in the identification of the IO box and the neccessary controls have been added.
Signed-off-by: Florian Faber <faberman@linuxproaudio.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SNDRV_HDSP_IOCTL_GET_CONFIG_INFO and
SNDRV_HDSP_IOCTL_GET_CONFIG_INFO ioctls in hdspm.c and hdsp.c allow
unprivileged users to read uninitialized kernel stack memory, because
several fields of the hdsp{m}_config_info structs declared on the stack
are not altered or zeroed before being copied back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use DEFINE_PCI_DEVICE_TABLE() to make PCI device ids go to
.devinit.rodata section, so they can be discarded in some cases,
and make them const.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
the hdsp driver refuses to report any information via the proc
interface, if the io box is not connected. with this patch, the
content of the control and status registers is printed before the
iobox check.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the use of the FIRMWARE_IN_KERNEL option with hdsp cards and
in-kernel driver.
Also corrected a typo in the comment.
Signed-off-by: Raphael Doursenaud <rdoursenaud@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ignore MIDI and PCM events in the interrupt handler until the device
gets initialized properly. Otherwise you may get kernel panic by the
access to uninitialized devices via hotplugging.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sleeping for 2 seconds before checking for the iobox is not enough
on some systems.
this patch increases the timeout, but polls the card during that
time. it thus speeds up the module loading when the card has already
been initialized, while being more robust on systems, which require
a higher timeout than the predefined 2 seconds.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace all tasklet_hi_schedule() callers with the normal
tasklet_schedule(). The former often causes troubles with
RT-kernels, and has actually no merit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The card->id (card text identification) can be changed at runtime.
It might be confusing to have old text identification in device name.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
currently, the error message when trying to run hdspmixer or hdspconf
if the breakout box is not connected is somehow misleading, since it
asks the user to upload the firmware.
this patch adds a test, whether the breakout box is connected and
tries to upload the firmware in the case, that it is not present, e.g.
because of power failures of the breakout box.
[Minor coding-style fixes by tiwai]
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
currently the hdsp driver tries to upload the firmware, even if the
io box is not connected. this patch adds a check for the io box
before trying to upload the firmware.
thus instead of messages complaining about the fifo status and firmware
loading failure, the driver gives a message that no multiface or
digiface is connected.
[A minor coding-style fix by tiwai]
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up SG-buffer helper functions and macros. Helpers take substream
as arguments now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Kill snd_assert() in sound/pci/*, either removed or replaced with
if () with snd_BUG_ON().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
sound/pci/rme9652/hdspm.c has unusually large number of static inline
functions - 22.
I looked through them and some of them seem to be too big to warrant inlining.
This patch removes "inline" from these static functions (regardless of number
of callsites - gcc nowadays auto-inlines statics with one callsite).
Size difference on 32bit x86:
text data bss dec hex filename
20437 2160 516 23113 5a49 linux-2.6-ALLYES/sound/pci/rme9652/hdspm.o
18036 2160 516 20712 50e8 linux-2.6.inline-ALLYES/sound/pci/rme9652/hdspm.o
[coding fix by Takashi Iwai <tiwai@suse.de>]
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bits indicating SPDIF frequency in the status register are not the same for
the 9632 than for the other cards, because it also supports 192kHz. A specific
bitmask has thus been added (used in hdsp_spdif_sample_rate()).
The 9632 does not seem to report external sample rates greater than 96kHz. In
this case, the best seems to report spdif rate when autosync reference is
spdif. This also required to move function hdsp_spdif_sample_rate().
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device has io_type == 1 (Multiface) and firmware_rev > 0xa
(fixes regression from changeset 5326)
Signed-off-by: Andreas Degert <ad@papyrus-gmbh.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix section mismatch in hdsp: snd_hdsp_proc_init() can be called from
an ioctl at any time.
WARNING: vmlinux.o(.text+0x1089bc2): Section mismatch: reference to .init.text: (between 'snd_hdsp_create_alsa_devices' and 'snd_hdsp_free')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly in the rest of
PCI drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove duplicated defines.
(From their use it looks like 'midiDataOutx are written to
rather than read from.)
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
added support for the latest revision of the 9632 (and hopefully a few
following ones). The DSP matrix was not working because of wrong
identification of the card in this part of the code.
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
* better report of speed mode change failures
* autosync_ref control bugfix (was reporting pref_sync_ref instead)
(changed HDSPM_AES32_AUTOSYNC_FROM_NONE value to comply with array
indexing in snd_hdspm_info_autosync_ref())
* added support for master modes up to 192kHz (clock source control
value was restricted up to 96kHz)
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix codes to follow more to the standard kernel coding style.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Clean up codes using the new common snd_ctl_boolean_*_info() callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The negative check in hw_pointer callback doesn't work because the
value is unsigned. Cast to int in the comparison to fix this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add 'DDS Sample Rate Offset' control. Allows values in Hz from -5000 to +5000.
The value is added to the nominal sample rate and written to the DDS register.
Signed-off-by: Julian Cable <julian_cable@yahoo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The current MADI driver was found not to completely work, at least on recent
MADI cards (rev 204), in particular at 96kHz. This patch solves this:
* Add support of DDS feature
* Channel map fixed
* Channel/rate rules fixed
* DMA allocation fixed (need to alloc for all channels and not only for the
used ones)
Full support for AES32 master mode was added:
* Add support of DDS feature
* Channel map fixed
* Channel/rate rules fixed
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added a new macro snd_pcm_group_for_each_entry() just for code cleanup.
Old macros, snd_pcm_group_for_each() and snd_pcm_group_substream_entry(),
are removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Adrian Knoth