this callback is called during suspend/resume and also via iw command.
it configures parameters like sifs, slottime, acktimeout in
ath9k_hw_init_global_settings where few REG_READ, REG_RMW are also done
and hence the need for PS wrappers
Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If is_main_vif(ar, vif) reports that we have to fall back
to software encryption, we goto err_softw; before locking ar->mutex.
As a result, we have unprotected call to carl9170_set_operating_mode
and unmatched mutex_unlock.
The patch fix the issue by adding mutex_lock before goto.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: <stable@kernel.org>
Acked-By: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After commit 5a865ba, we require a separate value to indicate the
number of supported SSIDs in scheduled scans. This patch adds a
proper value to the wl12xx driver.
This fixes a regression in 3.1-rc3 where scheduled scans were not
working properly with the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1271_sdio_power_on checks if the return value of pm_runtime_get_sync
is non-zero, and if so bails out.
However, pm_runtime_get_sync can return a positive number which does not
suggest an error has occurred. This is problematic for two reasons:
1. The function will needlessly bail out without decrementing back the
runtime PM reference counter.
2. wl1271_power_on only checks if wl1271_power_on return value is
negative. This means that wl1271_power_on will continue even if
wl1271_sdio_power_on bailed out. As a result, sdio transactions will
be initiated without properly enabling the sdio function and claiming
the host. This could even lead to a kernel panic.
Fix this by only checking that the return value of pm_runtime_get_sync
is non-negative.
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The testmode NVS push command is no longer in use. In addition, it has
several implementation issues that prevent it from working correctly:
1. wl1271_tm_cmd_configure relies on wl->chip.id being set. However,
since the device was not necessarily booted by the time the function
is called, wl->chip.id will be initialized to 0.
2. The NVS file is fetched by calling request_firmware() before it is
possible to push an NVS file.
3. The maximum allowed size of nl binary payloads is not sufficient for
pushing NVS files.
4. Pushing 128x NVS files will always fail due to a bug in the
validation code.
5. In case the pushed NVS file is found invalid, the mutex will be kept
locked and the nvs member will become a dangling pointer.
Since this feature is not being used, remove it completely instead of
fixing it.
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to some recent optimization done in the way the mac address
bytes are written into the OTP memory, some AR9485 chipsets were
forced to use the first byte from the eeprom template and the
remaining bytes are read from OTP.
AR9485 happens to use generic eeprom template which has 0x1 as
the first byte causes issues in bringing up the card.
So fixed the eeprom template accordingly to address the issue.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hibernating ->resume may not be called by usb core, but disconnect
and probe instead, so we do not increase the counter after decreasing
it in ->supend. As a result we free memory early, and get crash when
unplugging usb dongle.
BUG: unable to handle kernel paging request at 6b6b6b9f
IP: [<c06909b0>] driver_sysfs_remove+0x10/0x30
*pdpt = 0000000034f21001 *pde = 0000000000000000
Pid: 20, comm: khubd Not tainted 3.1.0-rc1-wl+ #20 LENOVO 6369CTO/6369CTO
EIP: 0060:[<c06909b0>] EFLAGS: 00010202 CPU: 1
EIP is at driver_sysfs_remove+0x10/0x30
EAX: 6b6b6b6b EBX: f52bba34 ECX: 00000000 EDX: 6b6b6b6b
ESI: 6b6b6b6b EDI: c0a0ea20 EBP: f61c9e68 ESP: f61c9e64
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process khubd (pid: 20, ti=f61c8000 task=f6138270 task.ti=f61c8000)
Call Trace:
[<c06909ef>] __device_release_driver+0x1f/0xa0
[<c0690b20>] device_release_driver+0x20/0x40
[<c068fd64>] bus_remove_device+0x84/0xe0
[<c068e12a>] ? device_remove_attrs+0x2a/0x80
[<c068e267>] device_del+0xe7/0x170
[<c06d93d4>] usb_disconnect+0xd4/0x180
[<c06d9d61>] hub_thread+0x691/0x1600
[<c0473260>] ? wake_up_bit+0x30/0x30
[<c0442a39>] ? complete+0x49/0x60
[<c06d96d0>] ? hub_disconnect+0xd0/0xd0
[<c06d96d0>] ? hub_disconnect+0xd0/0xd0
[<c0472eb4>] kthread+0x74/0x80
[<c0472e40>] ? kthread_worker_fn+0x150/0x150
[<c0809b3e>] kernel_thread_helper+0x6/0x10
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If hw does not support vlans, dont call nv_vlan_mode because it has no point.
I believe that this should fix issues on older non-vlan supportive
chips (like Ingo has).
Reported-ty: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's undesired to filter untagged packets at any time. So simply remove this.
Reported-by: Stephan Bärwolf <stephan.baerwolf@tu-ilmenau.de>
Tested-by: Stephan Bärwolf <stephan.baerwolf@tu-ilmenau.de>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eduard Sinelnikov (eduard.sinelnikov@gmail.com) found that if we change
bonding mode from active backup to round robin, some slaves are still keeping
"backup", and won't transmit packets.
As Jay Vosburgh(fubar@us.ibm.com) pointed out that we can work around that by
removing the bond_is_active_slave() check, because the "backup" flag is only
meaningful for active backup mode.
But if we just simply ignore the bond_is_active_slave() check,
the transmission will work fine, but we can't maintain the correct value of
"backup" flag for each slaves, though it is meaningless for other mode than
active backup.
I'd like to reset "backup" and "inactive" flag in bond_open,
thus we can keep the correct value of them.
As for bond_is_active_slave(), I'd like to prepare another patch to handle it.
V2:
Use C style comment.
Move read_lock(&bond->curr_slave_lock).
Replace restore with reset, for active backup mode, it means "restore",
but for other modes, it means "reset".
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/gianfar_ethtool.c:765: warning: the frame size of 2048 bytes is larger than 1024 bytes
Signed-off-by: Wang Shaoyan <wangshaoyan.pt@taobao.com>
Reviewed-and-tested-by: Sebastian Pöhn <sebastian.poehn@belden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some buggy chips, "vlan tag present" flag is set which causes packet
loss. Fix this by checking if rx vlan accel is enabled in features.
Reported-by: Michael Guntsche <mguntsche@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By a6b7a40786, remove interrupt.h
from netdevice.h. But this forget to revise sh_eth.
This fix the build failure.
error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_eth_interrupt'
error: implicit declaration of function 'request_irq'
error: 'sh_eth_interrupt' undeclared (first use in this function)
error: (Each undeclared identifier is reported only once
drivers/net/sh_eth.c:1386: error: for each function it appears in.)
error: 'IRQF_SHARED' undeclared (first use in this function)
error: implicit declaration of function 'free_irq'
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this code, the failure_cleanup label calls the function
plx_pci_del_card, which frees everything in the card->net_dev array. dev
is placed in this array immediately after allocation, so the two subsequent
jumps to failure_cleanup should not also call free_sja1000dev, but the
second one does.
If plx_pci_check_sja1000 fails, then free_sja1000dev is also called on
dev. Because dev is already in the card->net_dev array, this implies that
when plx_pci_del_card is later called, it may get freed again. So that
entry is reset to NULL after the free.
Finally, if there is a problem with one channel, there will be a hole in the
array. card->channels counts the number of channels that have succeeded,
and does not keep track of the index of the largest element in the array
that is valid. So the loop in plx_pci_del_card is changed to go up to
PLX_PCI_MAX_CHAN, which is only 2.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdc_ncm driver still has a few places where stack variables are
passed to the cdc_ncm_do_request function. This triggers a stack trace in
lib/dma-debug.c if the CONFIG_DEBUG_DMA_API option is set.
Adjust these calls to pass parameters that have been allocated with
kzalloc.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vmxnet3 driver enables vlan filters if filtering is enabled for
any vlan. In promiscuous mode the filter table is cleared to in
order to disable filtering. However, if a vlan device is subsequently
created that vlan will be added to the filter, re-engaging it. As a
result, not only do we not see all the vlans in promiscuous mode, we
don't even see vlans for which a filter was previously created.
CC: Scott J. Goldman <scottjg@vmware.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug has been introduced by:
d593411084
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date: Mon Jul 11 10:48:51 2011 +0300
iwlagn: simplify the bus architecture
Revert part of the buggy patch: dev_get_drvdata will now return
iwl_priv as it did before the patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit cc1a93e68f.
This fix introduced a bug: bad pointer in unload.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the Manageability Engine (ME) is enabled on 82579, it periodically
accesses some MAC CSR registers. There is an arbiter in hardware which
prevents simultaneous access of these registers by the host software, i.e.
the driver. There is a hardware bug in the aribter that signals a host
access of the registers later than it actually happens. A write of the
Transmit or Receive Descriptor Tail register could result in an incorrect
value if the driver and ME perform simultaneous accesses which could result
in an access to an invalid memory address. This would return an
Unsupported Request which could hang the hardware. Workaround the issue by
checking the FWSM register bit24 which is set by ME before it accesses the
MAC CSR registers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC can drop short packets when the PHY detects noise on the line at
100Mbps due to a timing issue. Workaround the issue by increasing the PLL
counter so the PHY properly recognizes the synchronization pattern from the
MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On 82577/8/9 in half-duplex when a received packet is passed from the PHY
to the MAC, if too many preamble octects are stripped from the packet
before arriving at the MAC, it can be misintrepeted as an in-band message
rather than an actual frame. For example, if the frame contents resembled
an interrupt request in-band message, it would trigger a false interrupt.
In most cases, the packet is just dropped.
By reducing the number of preamble octets stripped from the beginning of
the frame when passing it from the PHY to the MAC, the MAC will interpret
the frame properly.
An additional uses of the magic PHY_REG(770, 16) have been updated with a
define introduced with this patch.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to fix a memory leak found via code review for FCOE.
Specifically on DDP flows the SKBs were being dropped without being
recycled, freed, or given to the stack.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In each case, the freed data should be freed in the error handling code
as
well.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If word 0x37 in the EEPROM is 0xFFFF _or_ 0x0000, then there is no
alternate MAC address in the EEPROM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to a hardware erratum, the receiver on 82574 and 82583 should not be
stopped once it has been started.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This issue is present all the way back to 2.6.34 kernels.
CC: <stable@kernel.org>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeffrey Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In rt2800usb_work_txdone we check flags in order:
- ENTRY_OWNER_DEVICE_DATA
- ENTRY_DATA_STATUS_PENDING
- ENTRY_DATA_IO_FAILED
Modify flags in separate order in rt2x00usb_interrupt_txdone, to avoid
processing entries in _txdone with wrong flags or skip processing
ready entries.
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Building MIPS mtx1_defconfig results in:
MODPOST 735 modules
WARNING: drivers/net/pcnet32.o(.devinit.text+0x11ec): Section mismatch in reference from the function pcnet32_probe_vlbus.constprop.22() to the variable .init.data:pcnet32_portlist
The function __devinit pcnet32_probe_vlbus.constprop.22() references
a variable __initdata pcnet32_portlist.
If pcnet32_portlist is only used by pcnet32_probe_vlbus.constprop.22 then
annotate pcnet32_portlist with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tidyup below warning
${LINUX}/drivers/net/irda/sh_sir.c:514:6: warning:
'val' may be used uninitialized in this function
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixup below build error on sh_sir
sh_sir.c: In function 'sh_sir_write':
sh_sir.c:127:2: error: implicit declaration of function 'iowrite16'
sh_sir.c: In function 'sh_sir_read':
sh_sir.c:132:2: error: implicit declaration of function 'ioread16'
sh_sir.c: At top level:
sh_sir.c:561:20: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_sir_irq'
sh_sir.c: In function 'sh_sir_probe':
sh_sir.c:727:2: error: implicit declaration of function 'ioremap_nocache'
sh_sir.c:727:16: warning: assignment makes pointer from integer without a cast
sh_sir.c:762:2: error: implicit declaration of function 'request_irq'
sh_sir.c:762:23: error: 'sh_sir_irq' undeclared (first use in this function)
sh_sir.c:762:23: note: each undeclared identifier is reported only once for each function it appears in
sh_sir.c:762:35: error: 'IRQF_DISABLED' undeclared (first use in this function)
sh_sir.c:776:2: error: implicit declaration of function 'iounmap'
sh_sir.c: At top level:
sh_sir.c:436:13: warning: 'sh_sir_clear_all_err' defined but not used
sh_sir.c:474:12: warning: 'sh_sir_is_which_phase' defined but not used
sh_sir.c:490:13: warning: 'sh_sir_tx' defined but not used
sh_sir.c:540:13: warning: 'sh_sir_rx' defined but not used
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixup below build error on sh_irda
sh_irda.c: In function 'sh_irda_write':
sh_irda.c:174: error: implicit declaration of function 'iowrite16'
sh_irda.c: In function 'sh_irda_read':
sh_irda.c:184: error: implicit declaration of function 'ioread16'
sh_irda.c: At top level:
sh_irda.c:492: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_irda_irq'
sh_irda.c: In function 'sh_irda_probe':
sh_irda.c:776: error: implicit declaration of function 'ioremap_nocache'
sh_irda.c:776: warning: assignment makes pointer from integer without a cast
sh_irda.c:811: error: implicit declaration of function 'request_irq'
sh_irda.c:811: error: 'sh_irda_irq' undeclared (first use in this function)
sh_irda.c:811: error: (Each undeclared identifier is reported only once
sh_irda.c:811: error: for each function it appears in.)
sh_irda.c:811: error: 'IRQF_DISABLED' undeclared (first use in this function)
sh_irda.c:825: error: implicit declaration of function 'iounmap'
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As this discussion pointed out
http://marc.info/?l=linux-netdev&m=131257225602375
netdevices that are based on serial line disciplines should use netif_rx_ni()
when pushing received socketbuffers into the netdev rx queue.
Following commit 614851601c ("slip: fix NOHZ
local_softirq_pending 08 warning") this patch updates the slcan driver
accordingly.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Matvejchikov Ilya <matvejchikov@gmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In each case, the kfree already at the end of the function is also needed
in the error case.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This cleans up error handling for the beacon in case of dma mapping
failure. We need to free the skb when dma mapping fails instead of
nulling and leaking the pointer, and we should bail out to avoid
giving the hardware the bad descriptor.
Finally, we need to perform the null check after trying to update
the beacon, or else beacons will never be sent after a single
mapping failure.
Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add a device id for the wifi usb keys shiped by DVICO with
some of their tvix hardware.
Signed-off-by: Anthony Bourguignon <contact+kernel@toniob.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses an issue with incorrect HW register
AR_PHY_TX_IQCAL_CORR_COEFF_B1 definition which leads to incorrect clibration.
Cc: stable@kernel.org
Signed-off-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Maik-Holger Freudenberg <hhfeuer@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes several problems in the USB_DEVICE table, including missing IDs,
reversed vendor/product codes, and a duplicate ID.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit ebefce3d13 failed
to set proper PMU value to address ripple issue for AR9485.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CTL power data incorrect in ctlPowerData_2G field of ar9300_eeprom.
Setting incorrect CTL power in calibration is causing lower tx power.
Tx power was reported as 3dBm while operating in channel 6 HT40+/
in channel 11 HT40- due to CTL powers in the calibration is set to
zero.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This causes an databus error on a Broadcom SoC using bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dp83640 buffers receive time stamps from special PHY status frames,
matching them to received PTP packets in a work queue. Because the timeout
for orphaned time stamps is so long and the buffer is so small, the driver
can drop time stamps under moderate PTP traffic.
This commit fixes the issue by decreasing the timeout to (at least) one
timer tick and increasing the buffer size.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After resetting the time, the PPS signals on the FIPER output channels
are incorrectly offset from the clock time, as can be readily verified
by a looping back the FIPER to the external time stamp input.
Despite its name, setting the "Fiper Realignment Disable" bit seems to
fix the problem, at least on the P2020.
Also, following the example code from the Freescale BSP, it is not really
necessary to disable and re-enable the timer in order to reprogram the
FIPER. (The documentation is rather unclear on this point. It seems that
writing to the alarm register also disables the FIPER.)
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Executing cmd 'rmmod rtl8150' does not return(if your device connects
to host), the root cause is tasklet_disable() causes tasklet_kill()
block, remove it from rtl8150_disconnect().
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using nanosleep() in an userspace application we get a ratelimit warning:
NOHZ: local_softirq_pending 08
According to 481a819914 the problem is caused by
netif_rx() function. This patch replaces netif_rx() with netif_rx_ni() which
has to be used from process/softirq context.
Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
ipv6: check for IPv4 mapped addresses when connecting IPv6 sockets
mlx4: decreasing ref count when removing mac
net: Fix security_socket_sendmsg() bypass problem.
net: Cap number of elements for sendmmsg
net: sendmmsg should only return an error if no messages were sent
ixgbe: fix PHY link setup for 82599
ixgbe: fix __ixgbe_notify_dca() bail out code
igb: fix WOL on second port of i350 device
e1000e: minor re-order of #include files
e1000e: remove unnecessary check for NULL pointer
intel drivers: repair missing flush operations
macb: restore wrap bit when performing underrun cleanup
cdc_ncm: fix endianness problem.
irda: use PCI_VENDOR_ID_*
mlx4: Fixing Ethernet unicast packet steering
net: fix NULL dereferences in check_peer_redir()
bnx2x: Clear MDIO access warning during first driver load
bnx2x: Fix BCM578xx MAC test
bnx2x: Fix BCM54618se invalid link indication
bnx2x: Fix BCM84833 link
...
For older FW versions, when a Mac address removed from Mac table,
we should set 0 for reference count for the corresponding Mac index.
Fixes a bug where removing Mac from the table still left that entry as
invalid.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix pointer to setup_link for 82599.
This resolves some link issues when advertising modes unsupported
by the link partner.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The way __ixgbe_notify_dca() was currently set up it would not be
possible to add a requester. Both cases of the IXGBE_FLAG_DCA_ENABLED
bit being on and off would lead to the function exiting for a
DCA_PROVIDER_ADD.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where WOL would fail on second port of i350
device.
Reported-by: Martin Wilck <martin.wilck@ts.fujitsu.com>
Reported-by: Stefan Assmann<sassmann@redhat.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The recent commit a6b7a407 when back-ported to the out-of-tree e1000e
driver caused a compilation error on older kernels which required a
re-ordering of the #include files. This cosmetic patch syncs the two
drivers for easier maintainability.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The array shadow_ram is never NULL.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
after review of all intel drivers, found several instances where
drivers had the incorrect pattern of:
memory mapped write();
delay();
which should always be:
memory mapped write();
write flush(); /* aka memory mapped read */
delay();
explanation:
The reason for including the flush is that writes can be held
(posted) in PCI/PCIe bridges, but the read always has to complete
synchronously and therefore has to flush all pending writes to a
device. If a write is held and followed by a delay, the delay
means nothing because the write may not have reached hardware
(maybe even not until the next read)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When TX underrun occurs, a cleanup is performed that marks all buffers
as used. As a side effect it also clears the wrap bit in the last
buffer. This patch will restore the wrap bit.
Signed-off-by: Tord Andersson <tord.andersson@endian.se>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a misusage of the struct usb_cdc_notification to pass arguments to the
usb_control_msg function. The usb_control_msg function expects host endian
arguments but usb_cdc_notification stores these values as little endian.
Now usb_control_msg is directly invoked with host endian values.
Signed-off-by: Giuseppe Scrivano <giuseppe@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PCI_VENDOR_ID_* from pci_ids.h instead of creating #define locally.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
For older FW versions, fixing the usage of per port Mac table.
For each port we must define the base QP number, which is passed
to the HW.
Setting the correct value in SET_PORT FW command to enable the steering.
Reported-by: Roland Dreier <roland@purestorage.com>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After resetting BCM54618se, link partner would still see link since the PHY wasn't put into low-power state.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM84833 fail to link due to incorrect auto-negotiation setting.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix no-link issue on BCM578xx when direct attached cable is connected since Warpcore microcode restart was missing to re-read the new mode.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix resolve two problems seen regarding LED:
1. LED doesn't flash during port identification.
2. Traffic LED sometimes do not blink.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix MDIO access to Warpcore on new chip version of 578xx.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix couple of issues of remote fault detection and handling:
Link may go down due to remote fault indications during link establishment.
Possible link down after primary function migration.
Remote fault was not detected on 578xx.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem in which the 578xx chip hangs after running traffic, and then pulling the network cable.
This occurs since TX pipe is stalled due to missing XON indication towards the NIG.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link speed is 1G and below, pause weren't sent due to missing pause setting in the UMAC.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=39252
Hayes suggested that the usual MAC{0, 4} register writes be completed
with writes to extended GigaMAC registers :
- 0xe0 .. 0xe5
- 0xf2 .. 0xf7
Registers 0xf0 and 0xf1 should be set to 0.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5000 series has issue supporting power save idle mode:
commit 9dc2153315
iwlwifi: always support idle mode for agn devices
For agn devices, always support idle mode which help power
consumption in idle unassociated state.
the above changes cause 5000 become not stable when power management is "on"
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2312
Cc: stable@kernel.org #2.6.39, #3.0.0
Reported-by: Devin J Pohly <djpohly+iwl@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We may call rt2x00queue_pause_queue(queue) with queue == NULL. Bug
was introduced by commit 62fe778412
"rt2x00: Fix stuck queue in tx failure case" .
Cc: stable@kernel.org # 3.0+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced by commit
77b5621bac (rt2x00: Don't use queue entry
as parameter when creating TX descriptor.)
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug has been introduced by:
d593411084
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date: Mon Jul 11 10:48:51 2011 +0300
iwlagn: simplify the bus architecture
Revert part of the buggy patch: dev_get_drvdata will now return
iwl_priv as it did before the patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tx queues were stopped before bp->state was changed to a value different
from BNX2X_STATE_OPEN, which allowed the bnx2x_tx_int() called from the
NAPI context to re-enable it. This then allowed the netdev->ndo_start_xmit()
to be called in the middle of the function reset and rings freeing.
This patch changes bp->state to a value different
from BNX2X_STATE_OPEN BEFORE disabling the Tx queues in order to restore the
broken protection against the above race in the bnx2x_tx_int().
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should clear skb->data not skb itself. Bug was introduced by:
commit 0b8004aa12 "rt2x00: Properly
reserve room for descriptors in skbs".
Cc: stable@kernel.org # 2.6.36+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver uses information from the self member of the pci_bus struct to
get information regarding the bridge to which the PCIe device is attached.
Unfortunately, this member is not established on all architectures, which
leads to a kernel oops.
Skipping the entire block that uses the self member to determine the bridge
vendor will only affect RTL8192DE devices as that driver sets the ASPM support
flag differently when the bridge vendor is Intel. If the self member is
available, there is no functional change.
This patch fixes Bugzilla No. 40212.
Reported-by: Hubert Liao <liao.hubertt@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [back to 2.6.38]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We receive many bug reports about system hang during suspend/resume
when ath9k driver is in use. Adrian Chadd remarked that this problem
happens on systems that have ASPM disabled.
To do not hit the bug, skip doing ->config_pci_powersave magic if PCIe
downstream port device, which ath9k device is connected to, has ASPM
disabled.
Bug was introduced by:
commit 53bc7aa08b
Author: Vivek Natarajan <vnatarajan@atheros.com>
Date: Mon Apr 5 14:48:04 2010 +0530
ath9k: Add support for newer AR9285 chipsets.
Patch should address:
https://bugzilla.kernel.org/show_bug.cgi?id=37462https://bugzilla.kernel.org/show_bug.cgi?id=37082https://bugzilla.redhat.com/show_bug.cgi?id=697157
however I did not receive confirmation about that, except from Camilo
Mesias, whose system stops hang regularly with this patch (but still
hangs from time to time, but this is probably some other bug).
Tested-by: Camilo Mesias <camilo@mesias.co.uk>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If settings of tx power was deferred during scan or changing channel we
have to setup them during commit rxon. Fix problem on 3945 (4965 already
has this fix).
Optimize code to apply tx settings only when tx power was actually
changed.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With an uninitialized chainmask, the per-channel power will only contain
the power limits for a single chain instead of the combined tx power.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert array index from the loop bound to the loop index.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,ar;
@@
for(e1 = 0; e1 < e2; e1++) { <...
ar[
- e2
+ e1
]
...> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
smc91c92_cs.c: fix bogus compiler warning
orinoco_cs: be more careful when matching cards with ID 0x0156:0x0002
hostap_cs: support cards with "Version 01.02" as third product ID
pcmcia: add PCMCIA_DEVICE_MANF_CARD_PROD_ID3
pxa2xx pcmcia - stargate 2 use gpio array.
pcmcia: pxa2xx: remove empty socket_init / socket_resume functions.
drivers:pcmcia:soc_common: make socket_init and socket_suspend optional
* 'next/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (21 commits)
arm/dt: tegra devicetree support
arm/versatile: Add device tree support
dt/irq: add irq_domain_generate_simple() helper
irq: add irq_domain translation infrastructure
dmaengine: imx-sdma: add device tree probe support
dmaengine: imx-sdma: sdma_get_firmware does not need to copy fw_name
dmaengine: imx-sdma: use platform_device_id to identify sdma version
mmc: sdhci-esdhc-imx: add device tree probe support
mmc: sdhci-pltfm: dt device does not pass parent to sdhci_alloc_host
mmc: sdhci-esdhc-imx: get rid of the uses of cpu_is_mx()
mmc: sdhci-esdhc-imx: do not reference platform data after probe
mmc: sdhci-esdhc-imx: extend card_detect and write_protect support for mx5
net/fec: add device tree probe support
net: ibm_newemac: convert it to use of_get_phy_mode
dt/net: add helper function of_get_phy_mode
net/fec: gasket needs to be enabled for some i.mx
serial/imx: add device tree probe support
serial/imx: get rid of the uses of cpu_is_mx1()
arm/dt: Add dtb make rule
arm/dt: Add skeleton dtsi file
...
On a recent compile, I got this warning:
CC [M] drivers/net/pcmcia/smc91c92_cs.o
drivers/net/pcmcia/smc91c92_cs.c: In function ‘smc91c92_probe’:
drivers/net/pcmcia/smc91c92_cs.c:812:12: warning: ‘j’ may be used uninitialized in this function
However, "j" is only used in a branch which has the same condition as
a previous branch, where j is set, e.g.
int j;
if (CONDITION)
j = VALUE
...
if (CONDITION)
printk(j)
Still, avoid this warning, as it is easy to circumvent.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Without CONFIG_HERMES_PRISM, only match cards that have "Version 01.01"
as the third product ID. Those have Agere firmware.
With CONFIG_HERMES_PRISM, match all 0x0156:0x0002 cards.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cards with numeric ID 0x0156:0x0002 and third ID "Version 01.02" can be
assumed to have Intersil firmware. Cards with Agere firmware use
"Version 01.01".
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Only Sparc and PPC actually have the asm/prom.h include and as such they
can't be moved outside of the ifdefs.
Reported-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The D-Link DGE-530T rev C1 is a re-badged Realtek 8169 named DLG10028C,
unlike the previous revisions which were skge based. It is probably
the same as the discontinued DGE-528T (0x4300) other than the PCI ID.
The PCI ID is 0x1186:0x4302.
Adding it to r8169.c where 0x1186:0x4300 is already found makes the card
be detected and work.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=38862
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=34552
Signed-off-by: Klement Fish <klement2@azet.sk>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
tg3: Remove 5719 jumbo frames and TSO blocks
tg3: Break larger frags into 4k chunks for 5719
tg3: Add tx BD budgeting code
tg3: Consolidate code that calls tg3_tx_set_bd()
tg3: Add partial fragment unmapping code
tg3: Generalize tg3_skb_error_unmap()
tg3: Remove short DMA check for 1st fragment
tg3: Simplify tx bd assignments
tg3: Reintroduce tg3_tx_ring_info
ASIX: Use only 11 bits of header for data size
ASIX: Simplify condition in rx_fixup()
Fix cdc-phonet build
bonding: reduce noise during init
bonding: fix string comparison errors
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
net: add IFF_SKB_TX_SHARED flag to priv_flags
net: sock_sendmsg_nosec() is static
forcedeth: fix vlans
gianfar: fix bug caused by 87c288c6e9
gro: Only reset frag0 when skb can be pulled
...
The A0 revision of this chip is the only device that requires these
features to be disabled.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5719 has bug where RDMAs larger than 4k can cause problems. This
patch works around the problem by dividing larger DMA requests into
something the hardware can handle.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the driver breaks large skb fragments into smaller submissions to the
hardware, there is a new danger that BDs might get exhausted before all
fragments have been mapped. This patch adds code to make sure tx BDs
aren't oversubscribed and flag the condition if it happens.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates all code that populates tx BDs into a single
routine. Setting tx BDs needs to be more carefully controlled to see if
workarounds need to be applied.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patches are going to break skb fragments into smaller
sizes. This patch attempts to make the change easier to digest by only
addressing the skb teardown portion.
The patch modifies the driver to skip over any BDs that have a flag set
that indicates the BD isn't the beginning of an skb fragment. Such BDs
were a result of segmentation and do not need a pci_unmap_page() call.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the following patches, unmapping skb fragments will get just as
complicated as mapping them. This patch generalizes
tg3_skb_error_unmap() and makes it the one-stop-shop for skb unmapping.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first fragment of an skb should always be greater than 8 bytes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the following patches, the process the driver will use to assign skb
fragments to transmit BDs will get more complicated. To prepare for
that new code, this patch seeks to simplify how transmit BDs are
populated. It does this by separating the code that assigns the BD
members from the logic that controls how the fields are set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patches will require the use of an additional flag in the
ring_info structure. The use of this flag is tx path specific, so this
patch defines a specialized ring_info structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AX88772B uses only 11 bits of the header for the actual size. The other bits
are used for something else. This causes dmesg full of messages:
asix_rx_fixup() Bad Header Length
This patch trims the check to only 11 bits. I believe on older chips, the
remaining 5 top bits are unused.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to send to correct address this time!
---------- Forwarded Message ----------
Subject: [PATCH] Fix cdc-phonet build
Date: Saturday 23 Jul 2011
From: Chris Clayton <chris2553@googlemail.com>
To: linux-net@vger.kernel.org
cdc-phonet does not presently build on linux-3.0 because there is no entry for it in
drivers/net/Makefile. This patch adds that entry.
Signed-off-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Tue, Jul 26, 2011 at 05:40:27PM -0700, Joe Perches wrote:
> On Tue, 2011-07-26 at 17:37 -0700, Jay Vosburgh wrote:
> > Joe Perches <joe@perches.com> wrote:
> > >I'd prefer you don't separate the format string
> > >into multiple pieces.
> > Why not? To me, it looks easier to read split into sections
> > that don't wrap lines.
>
> Harder to grep for a dmesg and the
> defect rate of these split formats is
> typically higher than single strings
> because of bad spacing between string
> segments.
>
I noticed that you took some time back in late 2009 to 'consolidate' the
split format-strings present in the bonding driver at the time and I've
decided I'm fine to leave them the way they are. The main point of my
patch was to change the output and I would like to get that included.
Here is my updated patch...
Subject: [PATCH net-next-2.6 v2] bonding: reduce noise during init
Many are using sysfs to configure bonding rather than module options, so
there is no need for bonding to throw this warning in normal cases.
Keep the message around when debugging is enabled as it might be useful
for someone desperate enough to enable debugging, but eliminate it
otherwise.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bond contains a device where one name is the subset of another
(eth1 and eth10, for example), one cannot properly set the primary
device or the currently active device.
This was reported and based on work by Takuma Umeya. I also verified
the problem and tested that this fix resolves it.
V2: A few did not like the the current code or my changes, so I
refactored bonding_store_primary and bonding_store_active_slave to be a
bit cleaner, dropped the use of strnicmp since we did not really need
the comparison to be case insensitive, and formatted the input string
from sysfs so a comparison to IFNAMSIZ could be used.
I also discovered an error in bonding_store_active_slave that would
modify bond->primary_slave rather than bond->curr_active_slave before
forcing the bonding driver to choose a new active slave.
V3: Actually sending the proper patch....
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Takuma Umeya <tumeya@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs. There are a handful of drivers that violate this assumption of
course, and need to be fixed up. This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, when rxaccel is disabled, NV_RX3_VLAN_TAG_PRESENT is
still set and some pseudorandom vids appear. So check for
NETIF_F_HW_VLAN_RX as well. Also set correctly hw_features and set vlan
mode on probe.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 87c288c6e9 "gianfar: do vlan cleanup" has two issues:
# permutation of rx and tx flags
# enabling vlan tag insertion by default (this leads to unusable connections on some configurations)
If VLAN insertion is requested (via ethtool) it will be set at an other point ...
Signed-off-by: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It adds device tree probe support for fec driver.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
The patch extends 'enum phy_interface_t' and of_get_phy_mode a little
bit with PHY_INTERFACE_MODE_NA and PHY_INTERFACE_MODE_SMII added,
and then converts ibm_newemac net driver to use of_get_phy_mode
getting phy mode from device tree.
It also resolves the namespace conflict on phy_read/write between
common mdiobus interface and ibm_newemac private one.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Miller <davem@davemloft.net>
On the recent i.mx (mx25/50/53), there is a gasket inside fec
controller which needs to be enabled no matter phy works in MII
or RMII mode.
The current code enables the gasket only when phy interface is RMII.
It's broken when the driver works with a MII phy. The patch uses
platform_device_id to distinguish the SoCs that have the gasket and
enables it on these SoCs for both MII and RMII mode.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reported-by: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
wldev is freed in b43_one_core_detach() and should not be accessed after
that call. Keep wldev->dev in a local variable.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've fixed the last issue with BCMA support which caused memory
corruption on loading and unloading b43. Support for BCMA in b43 was
tested with 14e4:4353, 14e4:4357, 14e4:4727 and 14e4:4331. First two
cards (BCM43224 and BCM43225) are supported.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take Eric's patch one step further.
Use netdev_skb_ip_align to do setup the receive skb.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
This patch includes:
- Counting statistics ramrods as EQ ramrods the way they should be. This
accounting is meant to prevent MC asserts in case of software bugs.
- Fixes in debug facilities which were added while working on one of such
bugs.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fixes minor formatting in that function.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a result of DCBX negotiation some priorities maybe untouched and still
unmapped to any COS; instead of sending them to COS0 we assign them
to the same COS as L2 traffic - to avoid collisions with storage class of
service.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/via-velocity.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/qlge/qlge_main.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/igb/igb_main.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/can/c_can/c_can.c
drivers/net/can/c_can/c_can_platform.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/bna/bnad.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Consolidated bfa_sm.h and bfa_wc.h into bfa_cs.h
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Heartbeat failure counter is not incrementing under some scenarios.
Update hbfails and hb_count stats during hwerror event.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Added logic to unlock hw semaphore if the previos FW boot was from boot
code (flash based) and the current FW initialization attempt is from OS
driver.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Changed event name IOC_E_PFAILED to IOC_E_PFFAILED
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- If there is a command pending in the mailbox, bfa_ioc_mbox_queue() enqueues
the mailbox command to a pending command queue. Entries in this queue are
not flushed when IOC is disabled. As a result, when IOC is re-enabled again,
the stale entries in the pending command queue are posted to the mailbox.
When these mailbox commands are processed by the FW and responses are sent,
unexpected events are received by other modules' FSMs (f.e. bfa_msgq) which
have not posted any mailbox commands after IOC was enabled.
- Flush the pending mailbox command queue when IOC is disabled. Rename
bfa_ioc_mbox_hbfail to bfa_ioc_mbox_flush. Call bfa_ioc_mbox_flush
from bfa_iocpf_sm_disabled_entry()
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Always set mbox irq index to zero and make corresponding changes in mbox
irq alloc/sync function and txrx irq index calculation. Add definition of
BNAD_INTX_TX_IB_BITMASK & BNAD_INTX_RX_IB_BITMASK and update
bnad_txrx_irq_alloc accordingly.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chnage details:
- The module name is not used in case of state machine fault, hence no longer
passing the module name to the fault handler.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mohammed Shafi Shajakhan