Rewrites the siano IR implementation. The previous implementation were
non-standard. As such, it has issues if more than one device registers IR,
as there used to have some static constants used during protocol decoding
phase. Also, it used to implement its on RAW decoder, and only for RC5.
The new code uses RC core subsystem for handling IR. This brings several
new features to the driver, including:
- Allow to dynamically replace the IR keycodes;
- Supports all existing raw decoders (JVC, NEC, RC-5, RC-6, SONY);
- Supports lirc dev;
- Doesn't have race conditions when more than one sms IR is
registered;
- The code size for the IR implementation is very small;
- it exports the IR features via /sys/class/rc.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make id signed so we can't get an invalid pointer when we pass a negative
id.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add two additional USB targets, add these to the 'cards' modules
and to the 'smsusb' module.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the infra-red to the makefile and declare
the assignment in the cards components.
[mchehab@redhat.com: Fixed a few trivial merge conflicts]
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add gpio look-up table for various requirements, any
target may select any gpio and assign it to a function
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The smsdvb module was separated from the core and usb code. This change loads
smsdvb automatically for driver configurations that depend on it.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the usb_device_id table to the smsusb module in preparation for the
sms1xxx module to be split into sub-modules. This will allow the smsusb
driver to start up automatically upon insertion of the USB device.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Power the LNA while the frontend is in use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable power LED while the frontend is in use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This should have read, "GNU General Public License version 2"
rather than, "GNU General Public License version 3"
This was actually a typo mass-blunder -- this is not a change in licence,
as the code was always GPLv2.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the capability to define device-specific firmware filenames for the SMS1150,
with a mechanism to fall back to the generic firmware if the device-specific
firmware is not present.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Set board ID in the usb_device_id table's driver_info field.
Use board name when registering the dvb adapter.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab