Lennert reported a failure to add different mpls encaps in a multipath
route:
$ ip -6 route add 1234::/16 \
nexthop encap mpls 10 via fe80::1 dev ens3 \
nexthop encap mpls 20 via fe80::1 dev ens3
RTNETLINK answers: File exists
The problem is that the duplicate nexthop detection does not compare
lwtunnel configuration. Add it.
Fixes: 19e42e4515 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Reported-by: João Taveira Araújo <joao.taveira@gmail.com>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 242d3a49a2 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf")
I assumed NETDEV_REGISTER and NETDEV_UNREGISTER are paired,
unfortunately, as reported by jeffy, netdev_wait_allrefs()
could rebroadcast NETDEV_UNREGISTER event until all refs are
gone.
We have to add an additional check to avoid this corner case.
For netdev_wait_allrefs() dev->reg_state is NETREG_UNREGISTERED,
for dev_change_net_namespace(), dev->reg_state is
NETREG_REGISTERED. So check for dev->reg_state != NETREG_UNREGISTERED.
Fixes: 242d3a49a2 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf")
Reported-by: jeffy <jeffy.chen@rock-chips.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DST_NOCACHE flag check has been removed from dst_release() and
dst_hold_safe() in a previous patch because all the dst are now ref
counted properly and can be released based on refcnt only.
Looking at the rest of the DST_NOCACHE use, all of them can now be
removed or replaced with other checks.
So this patch gets rid of all the DST_NOCACHE usage and remove this flag
completely.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all the components have been changed to release dst based on
refcnt only and not depend on dst gc anymore, we can remove the
temporary flag DST_NOGC.
Note that we also need to remove the DST_NOCACHE check in dst_release()
and dst_hold_safe() because now all the dst are released based on refcnt
and behaves as DST_NOCACHE.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmp6 dst route is currently ref counted during creation and will be
freed by user during its call of dst_release(). So no need of a garbage
collector for it.
Remove all icmp6 dst garbage collector related code.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the previous preparation patches, we are ready to get rid of the
dst gc operation in ipv6 code and release dst based on refcnt only.
So this patch adds DST_NOGC flag for all IPv6 dst and remove the calls
to dst_free() and its related functions.
At this point, all dst created in ipv6 code do not use the dst gc
anymore and will be destroyed at the point when refcnt drops to 0.
Also, as icmp6 dst route is refcounted during creation and will be freed
by user during its call of dst_release(), there is no need to add this
dst to the icmp6 gc list as well.
Instead, we need to add it into uncached list so that when a
NETDEV_DOWN/NETDEV_UNREGISRER event comes, we can properly go through
these icmp6 dst as well and release the net device properly.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar as ipv4, ipv6 path also needs to call dst_hold_safe() when
necessary to avoid double free issue on the dst.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In IPv6 routing code, struct rt6_info is created for each static route
and RTF_CACHE route and inserted into fib6 tree. In both cases, dst
ref count is not taken.
As explained in the previous patch, this leads to the need of the dst
garbage collector.
This patch holds ref count of dst before inserting the route into fib6
tree and properly releases the dst when deleting it from the fib6 tree
as a preparation in order to fully get rid of dst gc later.
Also, correct fib6_age() logic to check dst->__refcnt to be 1 to indicate
no user is referencing the dst.
And remove dst_hold() in vrf_rt6_create() as ip6_dst_alloc() already puts
dst->__refcnt to 1.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing ipv4/6_blackhole_route() code generates a blackhole route
with dst->dev pointing to the passed in dst->dev.
It is not necessary to hold reference to the passed in dst->dev
because the packets going through this route are dropped anyway.
A loopback interface is good enough so that we don't need to worry about
releasing this dst->dev when this dev is going down.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa reported attempts to delete a bond device that is referenced in a
multipath route is hanging:
$ ifdown bond2 # ifupdown2 command that deletes virtual devices
unregister_netdevice: waiting for bond2 to become free. Usage count = 2
Steps to reproduce:
echo 1 > /proc/sys/net/ipv6/conf/all/ignore_routes_with_linkdown
ip link add dev bond12 type bond
ip link add dev bond13 type bond
ip addr add 2001:db8:2::0/64 dev bond12
ip addr add 2001:db8:3::0/64 dev bond13
ip route add 2001:db8:33::0/64 nexthop via 2001:db8:2::2 nexthop via 2001:db8:3::2
ip link del dev bond12
ip link del dev bond13
The root cause is the recent change to keep routes on a linkdown. Update
the check to detect when the device is unregistering and release the
route for that case.
Fixes: a1a22c1206 ("net: ipv6: Keep nexthop of multipath route on admin down")
Reported-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack arg down to lwtunnel_build_state and the build_state callbacks.
Add messages for failures in lwtunnel_build_state, and add the extarg to
nla_parse where possible in the build_state callbacks.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack down to lwtunnel_valid_encap_type and
lwtunnel_valid_encap_type_attr. Add messages for unknown
or unsupported encap types.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to return matched fib result when RTM_F_FIB_MATCH
flag is specified in RTM_GETROUTE request. This is useful for user-space
applications/controllers wanting to query a matching route.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add messages for non-obvious errors (e.g, no need to add text for malloc
failures or ENODEV failures). This mostly covers the annoying EINVAL errors
Some message strings violate the 80-columns but searchable strings need to
trump that rule.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each netns (except init_net), we initialize its null entry
in 3 places:
1) The template itself, as we use kmemdup()
2) Code around dst_init_metrics() in ip6_route_net_init()
3) ip6_route_dev_notify(), which is supposed to initialize it after
loopback registers
Unfortunately the last one still happens in a wrong order because
we expect to initialize net->ipv6.ip6_null_entry->rt6i_idev to
net->loopback_dev's idev, thus we have to do that after we add
idev to loopback. However, this notifier has priority == 0 same as
ipv6_dev_notf, and ipv6_dev_notf is registered after
ip6_route_dev_notifier so it is called actually after
ip6_route_dev_notifier. This is similar to commit 2f460933f5
("ipv6: initialize route null entry in addrconf_init()") which
fixes init_net.
Fix it by picking a smaller priority for ip6_route_dev_notifier.
Also, we have to release the refcnt accordingly when unregistering
loopback_dev because device exit functions are called before subsys
exit functions.
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a crash on init_net.ipv6.ip6_null_entry->rt6i_idev
since it is always NULL.
This is clearly wrong, we have code to initialize it to loopback_dev,
unfortunately the order is still not correct.
loopback_dev is registered very early during boot, we lose a chance
to re-initialize it in notifier. addrconf_init() is called after
ip6_route_init(), which means we have no chance to correct it.
Fix it by moving this initialization explicitly after
ipv6_add_dev(init_net.loopback_dev) in addrconf_init().
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both conflict were simple overlapping changes.
In the kaweth case, Eric Dumazet's skb_cow() bug fix overlapped the
conversion of the driver in net-next to use in-netdev stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a fault in the IPv6 route code:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 1 PID: 4035 Comm: a.out Not tainted 4.11.0-rc7+ #250
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff880069809600 task.stack: ffff880062dc8000
RIP: 0010:ip6_rt_cache_alloc+0xa6/0x560 net/ipv6/route.c:975
RSP: 0018:ffff880062dced30 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: ffff8800670561c0 RCX: 0000000000000006
RDX: 0000000000000003 RSI: ffff880062dcfb28 RDI: 0000000000000018
RBP: ffff880062dced68 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff880062dcfb28 R14: dffffc0000000000 R15: 0000000000000000
FS: 00007feebe37e7c0(0000) GS:ffff88006cb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000205a0fe4 CR3: 000000006b5c9000 CR4: 00000000000006e0
Call Trace:
ip6_pol_route+0x1512/0x1f20 net/ipv6/route.c:1128
ip6_pol_route_output+0x4c/0x60 net/ipv6/route.c:1212
...
Andrey's syzkaller program passes rtmsg.rtmsg_flags with the RTF_PCPU bit
set. Flags passed to the kernel are blindly copied to the allocated
rt6_info by ip6_route_info_create making a newly inserted route appear
as though it is a per-cpu route. ip6_rt_cache_alloc sees the flag set
and expects rt->dst.from to be set - which it is not since it is not
really a per-cpu copy. The subsequent call to __ip6_dst_alloc then
generates the fault.
Fix by checking for the flag and failing with EINVAL.
Fixes: d52d3997f8 ("ipv6: Create percpu rt6_info")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink_ext_ack arg to rtnl_doit_func. Pass extack arg to nlmsg_parse
for doit functions that call it directly.
This is the first step to using extended error reporting in rtnetlink.
>From here individual subsystems can be updated to set netlink_ext_ack as
needed.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anycast routes have the RTF_ANYCAST flag set, but when dumping routes
for userspace the route type is not set to RTN_ANYCAST. Make it so.
Fixes: 58c4fb86ea ("[IPV6]: Flag RTF_ANYCAST for anycast routes")
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dinesh reported that RTA_MULTIPATH nexthops are 8-bytes larger with IPv6
than IPv4. The recent refactoring for multipath support in netlink
messages does discriminate between non-multipath which needs the OIF
and multipath which adds a rtnexthop struct for each hop making the
RTA_OIF attribute redundant. Resolve by adding a flag to the info
function to skip the oif for multipath.
Fixes: beb1afac51 ("net: ipv6: Add support to dump multipath routes
via RTA_MULTIPATH attribute")
Reported-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like commit 1f17e2f2c8 ("net: ipv6: ignore null_entry on route dumps"),
we need to ignore null entry in inet6_rtm_getroute() too.
Return -ENETUNREACH here to sync with IPv4 behavior, as suggested by David.
Fixes: a1a22c1206 ("net: ipv6: Keep nexthop of multipath route on admin down")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a NULL pointer deref bug in ipv6_route_ioctl()
-> ip6_route_del() -> __ip6_del_rt_siblings() code path. This is
because ip6_null_entry is returned in this path since ip6_null_entry
is kinda default for a ipv6 route table root node. Quote from
David Ahern:
ip6_null_entry is the root of all ipv6 fib tables making it integrated
into the table ...
We should ignore any attempt of trying to delete it, like we do in
__ip6_del_rt() path and several others.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Fixes: 0ae8133586 ("net: ipv6: Allow shorthand delete of all nexthops in multipath route")
Cc: David Ahern <dsa@cumulusnetworks.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will add stricter validating for RTA_MARK attribute.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
The datagram protocols can use MSG_CONFIRM to confirm the
neighbour. When used with MSG_PROBE we do not reach the
code where neighbour is confirmed, so we have to do the
same slow lookup by using the dst_confirm_neigh() helper.
When MSG_PROBE is not used, ip_append_data/ip6_append_data
will set the skb flag dst_pending_confirm.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8 ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf3 ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add confirm_neigh method to dst_ops and use it from IPv4 and IPv6
to lookup and confirm the neighbour. Its usage via the new helper
dst_confirm_neigh() should be restricted to MSG_PROBE users for
performance reasons.
For XFRM prefer the last tunnel address, if present. With help
from Steffen Klassert.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_print_replace_route_err logs an error if a route replace fails with
IPv6 addresses in the full format. e.g,:
IPv6: IPV6: multipath route replace failed (check consistency of installed routes): 2001:0db8:0200:0000:0000:0000:0000:0000 nexthop 2001:0db8:0001:0000:0000:0000:0000:0016 ifi 0
Change the message to dump the addresses in the compressed format.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an entire multipath route is deleted using prefix and len (without any
nexthops), send a single RTM_DELROUTE notification with the full route
using RTA_MULTIPATH. This is done by generating the skb before the route
delete when all of the sibling routes are still present but sending it
after the route has been removed from the FIB. The skip_notify flag
is used to tell the lower fib code not to send notifications for the
individual nexthop routes.
If a route is deleted using RTA_MULTIPATH for any nexthops or a single
nexthop entry is deleted, then the nexthops are deleted one at a time with
notifications sent as each hop is deleted. This is necessary given that
IPv6 allows individual hops within a route to be deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ip6_route_multipath_add to send one notifciation with the full
route encoded with RTA_MULTIPATH instead of a series of individual routes.
This is done by adding a skip_notify flag to the nl_info struct. The
flag is used to skip sending of the notification in the fib code that
actually inserts the route. Once the full route has been added, a
notification is generated with all nexthops.
ip6_route_multipath_add handles 3 use cases: new routes, route replace,
and route append. The multipath notification generated needs to be
consistent with the order of the nexthops and it should be consistent
with the order in a FIB dump which means the route with the first nexthop
needs to be used as the route reference. For the first 2 cases (new and
replace), a reference to the route used to send the notification is
obtained by saving the first route added. For the append case, the last
route added is used to loop back to its first sibling route which is
the first nexthop in the multipath route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 returns multipath routes as a series of individual routes making
their display and handling by userspace different and more complicated
than IPv4, putting the burden on the user to see that a route is part of
a multipath route and internally creating a multipath route if desired
(e.g., libnl does this as of commit 29b71371e764). This patch addresses
this difference, allowing multipath routes to be returned using the
RTA_MULTIPATH attribute.
The end result is that IPv6 multipath routes can be treated and displayed
in a format similar to IPv4:
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 allows multipath routes to be deleted using just the prefix and
length. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.11.200.2 dev eth11.200 weight 1
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
$ ip ro del 1.1.1.0/24 vrf red
$ ip ro ls vrf red
unreachable default metric 8192
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
The same notation does not work with IPv6 because of how multipath routes
are implemented for IPv6. For IPv6 only the first nexthop of a multipath
route is deleted if the request contains only a prefix and length. This
leads to unnecessary complexity in userspace dealing with IPv6 multipath
routes.
This patch allows all nexthops to be deleted without specifying each one
in the delete request. Internally, this is done by walking the sibling
list of the route matching the specifications given (prefix, length,
metric, protocol, etc).
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 via 2001:db8:1::2 dev eth1 metric 1024 pref medium
2001:db8:200::/120 via 2001:db8:2::2 dev eth2 metric 1024 pref medium
...
$ ip -6 ro del vrf red 2001:db8:200::/120
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
...
Because IPv6 allows individual nexthops to be deleted without deleting
the entire route, the ip6_route_multipath_del and non-multipath code
path (ip6_route_del) have to be discriminated so that all nexthops are
only deleted for the latter case. This is done by making the existing
fc_type in fib6_config a u16 and then adding a new u16 field with
fc_delete_all_nh as the first bit.
Suggested-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 stack does not set the protocol for local routes, so those routes show
up with proto "none":
$ ip -6 ro ls table local
local ::1 dev lo proto none metric 0 pref medium
local 2100:3:: dev lo proto none metric 0 pref medium
local 2100:3::4 dev lo proto none metric 0 pref medium
local fe80:: dev lo proto none metric 0 pref medium
...
Set rt6i_protocol to RTPROT_KERNEL for consistency with IPv4. Now routes
show up with proto "kernel":
$ ip -6 ro ls table local
local ::1 dev lo proto kernel metric 0 pref medium
local 2100:3:: dev lo proto kernel metric 0 pref medium
local 2100:3::4 dev lo proto kernel metric 0 pref medium
local fe80:: dev lo proto kernel metric 0 pref medium
...
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing about lwt state requires a device reference, so remove the
input argument.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lkp-robot reported a BUG:
[ 10.151226] BUG: unable to handle kernel NULL pointer dereference at 00000198
[ 10.152525] IP: rt6_fill_node+0x164/0x4b8
[ 10.153307] *pdpt = 0000000012ee5001 *pde = 0000000000000000
[ 10.153309]
[ 10.154492] Oops: 0000 [#1]
[ 10.154987] CPU: 0 PID: 909 Comm: netifd Not tainted 4.10.0-rc4-00722-g41e8c70ee162-dirty #10
[ 10.156482] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 10.158254] task: d0deb000 task.stack: d0e0c000
[ 10.159059] EIP: rt6_fill_node+0x164/0x4b8
[ 10.159780] EFLAGS: 00010296 CPU: 0
[ 10.160404] EAX: 00000000 EBX: d10c2358 ECX: c1f7c6cc EDX: c1f6ff44
[ 10.161469] ESI: 00000000 EDI: c2059900 EBP: d0e0dc4c ESP: d0e0dbe4
[ 10.162534] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
[ 10.163482] CR0: 80050033 CR2: 00000198 CR3: 10d94660 CR4: 000006b0
[ 10.164535] Call Trace:
[ 10.164993] ? paravirt_sched_clock+0x9/0xd
[ 10.165727] ? sched_clock+0x9/0xc
[ 10.166329] ? sched_clock_cpu+0x19/0xe9
[ 10.166991] ? lock_release+0x13e/0x36c
[ 10.167652] rt6_dump_route+0x4c/0x56
[ 10.168276] fib6_dump_node+0x1d/0x3d
[ 10.168913] fib6_walk_continue+0xab/0x167
[ 10.169611] fib6_walk+0x2a/0x40
[ 10.170182] inet6_dump_fib+0xfb/0x1e0
[ 10.170855] netlink_dump+0xcd/0x21f
This happens when the loopback device is set down and a ipv6 fib route
dump is requested.
ip6_null_entry is the root of all ipv6 fib tables making it integrated
into the table and hence passed to the ipv6 route dump code. The
null_entry route uses the loopback device for dst.dev but may not have
rt6i_idev set because of the order in which initializations are done --
ip6_route_net_init is run before addrconf_init has initialized the
loopback device. Fixing the initialization order is a much bigger problem
with no obvious solution thus far.
The BUG is triggered when the loopback is set down and the netif_running
check added by a1a22c1206 fails. The fill_node descends to checking
rt->rt6i_idev for ignore_routes_with_linkdown and since rt6i_idev is
NULL it faults.
The null_entry route should not be processed in a dump request. Catch
and ignore. This check is done in rt6_dump_route as it is the highest
place in the callchain with knowledge of both the route and the network
namespace.
Fixes: a1a22c1206("net: ipv6: Keep nexthop of multipath route on admin down")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove skb_reserve and skb_reset_mac_header from inet6_rtm_getroute. The
allocated skb is not passed through the routing engine (like it is for
IPv4) and has not since the beginning of git time.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 deletes route entries associated with multipath routes on an
admin down where IPv4 does not. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24 metric 64
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.100.2.254 dev eth2 weight 1
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.4
10.100.2.0/24 dev eth2 proto kernel scope link src 10.100.2.4
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:1::16 dev eth1 metric 1024 pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Set link down:
$ ip li set eth1 down
IPv4 retains the multihop route but flags eth1 route as dead:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.16 dev eth1 weight 1 dead linkdown
nexthop via 10.100.2.16 dev eth2 weight 1
10.100.2.0/24 dev eth2 proto kernel scope link src 10.100.2.4
and IPv6 deletes the route as part of flushing all routes for the device:
$ ip -6 ro ls vrf red
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Worse, on admin up of the device the multipath route has to be deleted
to get this leg of the route re-added.
This patch keeps routes that are part of a multipath route if
ignore_routes_with_linkdown is set with the dead and linkdown flags
enabling consistency between IPv4 and IPv6:
$ ip -6 ro ls vrf red
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:1::16 dev eth1 metric 1024 dead linkdown pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to add an mpls encap route when the MPLS modules are not loaded
hangs. For example:
CONFIG_MPLS=y
CONFIG_NET_MPLS_GSO=m
CONFIG_MPLS_ROUTING=m
CONFIG_MPLS_IPTUNNEL=m
$ ip route add 10.10.10.10/32 encap mpls 100 via inet 10.100.1.2
The ip command hangs:
root 880 826 0 21:25 pts/0 00:00:00 ip route add 10.10.10.10/32 encap mpls 100 via inet 10.100.1.2
$ cat /proc/880/stack
[<ffffffff81065a9b>] call_usermodehelper_exec+0xd6/0x134
[<ffffffff81065efc>] __request_module+0x27b/0x30a
[<ffffffff814542f6>] lwtunnel_build_state+0xe4/0x178
[<ffffffff814aa1e4>] fib_create_info+0x47f/0xdd4
[<ffffffff814ae451>] fib_table_insert+0x90/0x41f
[<ffffffff814a8010>] inet_rtm_newroute+0x4b/0x52
...
modprobe is trying to load rtnl-lwt-MPLS:
root 881 5 0 21:25 ? 00:00:00 /sbin/modprobe -q -- rtnl-lwt-MPLS
and it hangs after loading mpls_router:
$ cat /proc/881/stack
[<ffffffff81441537>] rtnl_lock+0x12/0x14
[<ffffffff8142ca2a>] register_netdevice_notifier+0x16/0x179
[<ffffffffa0033025>] mpls_init+0x25/0x1000 [mpls_router]
[<ffffffff81000471>] do_one_initcall+0x8e/0x13f
[<ffffffff81119961>] do_init_module+0x5a/0x1e5
[<ffffffff810bd070>] load_module+0x13bd/0x17d6
...
The problem is that lwtunnel_build_state is called with rtnl lock
held preventing mpls_init from registering.
Given the potential references held by the time lwtunnel_build_state it
can not drop the rtnl lock to the load module. So, extract the module
loading code from lwtunnel_build_state into a new function to validate
the encap type. The new function is called while converting the user
request into a fib_config which is well before any table, device or
fib entries are examined.
Fixes: 745041e2aa ("lwtunnel: autoload of lwt modules")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prefix arg to rt6_fill_node is non-0 in only 1 path - rt6_dump_route
where a user is requesting a prefix only dump. Simplify rt6_fill_node
by removing the prefix arg and moving the prefix check to rt6_dump_route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers of rt6_fill_node pass 0 for nowait arg. Remove the arg and
simplify rt6_fill_node accordingly.
rt6_fill_node passes the nowait of 0 to ip6mr_get_route. Remove the
nowait arg from it as well.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle failure in lwtunnel_fill_encap adding attributes to skb.
Fixes: 571e722676 ("ipv4: support for fib route lwtunnel encap attributes")
Fixes: 19e42e4515 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o s/approriate/appropriate
o s/discouvery/discovery
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The protocol field is checked when deleting IPv4 routes, but ignored for
IPv6, which causes problems with routing daemons accidentally deleting
externally set routes (observed by multiple bird6 users).
This can be verified using `ip -6 route del <prefix> proto something`.
Signed-off-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Made kernel accept IPv6 routes with IPv4-mapped address as next-hop.
It is possible to configure IP interfaces with IPv4-mapped addresses, and
one can add IPv6 routes for IPv4-mapped destinations/prefixes, yet prior
to this fix the kernel returned an EINVAL when attempting to add an IPv6
route with an IPv4-mapped address as a nexthop/gateway.
RFC 4798 (a proposed standard RFC) uses IPv4-mapped addresses as nexthops,
thus in order to support that type of address configuration the kernel
needs to allow IPv4-mapped addresses as nexthops.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routes can specify an mtu explicitly or inherit the mtu from
the underlying device - this inheritance is implemented in
dst->ops->mtu handlers ip6_mtu() and ip6_blackhole_mtu().
Currently changing the mtu of a device adds mtu explicitly
to routes using that device.
ie.
# ip link set dev lo mtu 65536
# ip -6 route add local 2000::1 dev lo
# ip -6 route get 2000::1
local 2000::1 dev lo table local src ... metric 1024 pref medium
# ip link set dev lo mtu 65535
# ip -6 route get 2000::1
local 2000::1 dev lo table local src ... metric 1024 mtu 65535 pref medium
# ip link set dev lo mtu 65536
# ip -6 route get 2000::1
local 2000::1 dev lo table local src ... metric 1024 mtu 65536 pref medium
# ip -6 route del local 2000::1
After this patch the route entry no longer changes unless it already has an mtu.
There is no need: this inheritance is already done in ip6_mtu()
# ip link set dev lo mtu 65536
# ip -6 route add local 2000::1 dev lo
# ip -6 route add local 2000::2 dev lo mtu 2000
# ip -6 route get 2000::1; ip -6 route get 2000::2
local 2000::1 dev lo table local src ... metric 1024 pref medium
local 2000::2 dev lo table local src ... metric 1024 mtu 2000 pref medium
# ip link set dev lo mtu 65535
# ip -6 route get 2000::1; ip -6 route get 2000::2
local 2000::1 dev lo table local src ... metric 1024 pref medium
local 2000::2 dev lo table local src ... metric 1024 mtu 2000 pref medium
# ip link set dev lo mtu 1501
# ip -6 route get 2000::1; ip -6 route get 2000::2
local 2000::1 dev lo table local src ... metric 1024 pref medium
local 2000::2 dev lo table local src ... metric 1024 mtu 1501 pref medium
# ip link set dev lo mtu 65536
# ip -6 route get 2000::1; ip -6 route get 2000::2
local 2000::1 dev lo table local src ... metric 1024 pref medium
local 2000::2 dev lo table local src ... metric 1024 mtu 65536 pref medium
# ip -6 route del local 2000::1
# ip -6 route del local 2000::2
This is desirable because changing device mtu and then resetting it
to the previous value shouldn't change the user visible routing table.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
CC: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the UID in routing lookups made by protocol connect() and
sendmsg() functions.
- Make sure that routing lookups triggered by incoming packets
(e.g., Path MTU discovery) take the UID of the socket into
account.
- For packets not associated with a userspace socket, (e.g., ping
replies) use UID 0 inside the user namespace corresponding to
the network namespace the socket belongs to. This allows
all namespaces to apply routing and iptables rules to
kernel-originated traffic in that namespaces by matching UID 0.
This is better than using the UID of the kernel socket that is
sending the traffic, because the UID of kernel sockets created
at namespace creation time (e.g., the per-processor ICMP and
TCP sockets) is the UID of the user that created the socket,
which might not be mapped in the namespace.
Tested: compiles allnoconfig, allyesconfig, allmodconfig
Tested: https://android-review.googlesource.com/253302
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Define a new FIB rule attributes, FRA_UID_RANGE, to describe a
range of UIDs.
- Define a RTA_UID attribute for per-UID route lookups and dumps.
- Support passing these attributes to and from userspace via
rtnetlink. The value INVALID_UID indicates no UID was
specified.
- Add a UID field to the flow structures.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, ipv6 didn't do mtu lock check in ip6_update_pmtu.
It leaded to that mtu lock doesn't really work when receiving the pkt
of ICMPV6_PKT_TOOBIG.
This patch is to add mtu lock check in __ip6_rt_update_pmtu just as ipv4
did in __ip_rt_update_pmtu.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv4, do not consider link state when validating next hops.
Currently, if the link is down default routes can fail to insert:
$ ip -6 ro add vrf blue default via 2100:2::64 dev eth2
RTNETLINK answers: No route to host
With this patch the command succeeds.
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_add_route_info and rt6_add_dflt_router were updated to pull the FIB
table from the device index, but the corresponding rt6_get_route_info
and rt6_get_dflt_router functions were not leading to the failure to
process RA's:
ICMPv6: RA: ndisc_router_discovery failed to add default route
Fix the 'get' functions by using the table id associated with the
device when applicable.
Also, now that default routes can be added to tables other than the
default table, rt6_purge_dflt_routers needs to be updated as well to
look at all tables. To handle that efficiently, add a flag to the table
denoting if it is has a default route via RA.
Fixes: ca254490c8 ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8c14586fc3 ("net: ipv6: Use passed in table for nexthop
lookups") introduced a regression: insertion of an IPv6 route in a table
not containing the appropriate connected route for the gateway but which
contained a non-connected route (like a default gateway) fails while it
was previously working:
$ ip link add eth0 type dummy
$ ip link set up dev eth0
$ ip addr add 2001:db8::1/64 dev eth0
$ ip route add ::/0 via 2001:db8::5 dev eth0 table 20
$ ip route add 2001:db8:cafe::1/128 via 2001:db8::6 dev eth0 table 20
RTNETLINK answers: No route to host
$ ip -6 route show table 20
default via 2001:db8::5 dev eth0 metric 1024 pref medium
After this patch, we get:
$ ip route add 2001:db8:cafe::1/128 via 2001:db8::6 dev eth0 table 20
$ ip -6 route show table 20
2001:db8:cafe::1 via 2001:db8::6 dev eth0 metric 1024 pref medium
default via 2001:db8::5 dev eth0 metric 1024 pref medium
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make ip6_route_input_lookup available outside of ipv6 the module
similar to ip_route_input_noref in the IPv4 world.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous patch added l3mdev flow update making these hooks
redundant. Remove them.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flip the IPv6 output path to use the l3mdev tx out hook. The VRF dst
is not returned on the first FIB lookup. Instead, the dst on the
skb is switched at the beginning of the IPv6 output processing to
send the packet to the VRF driver on xmit.
Link scope addresses (linklocal and multicast) need special handling:
specifically the oif the flow struct can not be changed because we
want the lookup tied to the enslaved interface. ie., the source address
and the returned route MUST point to the interface scope passed in.
Convert the existing vrf_get_rt6_dst to handle only link scope addresses.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow an L3 master device to act as the loopback for that L3 domain.
For IPv4 the device can also have the address 127.0.0.1.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today mpls iptunnel lwtunnel_output redirect expects the tunnel
output function to handle fragmentation. This is ok but can be
avoided if we did not do the mpls output redirect too early.
ie we could wait until ip fragmentation is done and then call
mpls output for each ip fragment.
To make this work we will need,
1) the lwtunnel state to carry encap headroom
2) and do the redirect to the encap output handler on the ip fragment
(essentially do the output redirect after fragmentation)
This patch adds tunnel headroom in lwtstate to make sure we
account for tunnel data in mtu calculations during fragmentation
and adds new xmit redirect handler to redirect to lwtunnel xmit func
after ip fragmentation.
This includes IPV6 and some mtu fixes and testing from David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
with the commit 8c14586fc3 ("net: ipv6: Use passed in table for
nexthop lookups"), net hop lookup is first performed on route creation
in the passed-in table.
However device match is not enforced in table lookup, so the found
route can be later discarded due to egress device mismatch and no
global lookup will be performed.
This cause the following to fail:
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip route add 2001:db8:8086::/48 dev dummy1 metric 20
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy1 metric 20
ip route add 2001:db8:8086::/48 dev dummy2 metric 21
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy2 metric 21
RTNETLINK answers: No route to host
This change fixes the issue enforcing device lookup in
ip6_nh_lookup_table()
v1->v2: updated commit message title
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Reported-and-tested-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VRF driver needs access to ip6_route_get_saddr code. Since it does
little beyond ipv6_dev_get_saddr and ipv6_dev_get_saddr is already
exported for modules move ip6_route_get_saddr to the header as an
inline.
Code move only; no functional change.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces neighbour discovery ops callback structure. The
idea is to separate the handling for 6LoWPAN into the 6lowpan module.
These callback offers 6lowpan different handling, such as 802.15.4 short
address handling or RFC6775 (Neighbor Discovery Optimization for IPv6
over 6LoWPANs).
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 multicast and link-local addresses require special handling by the
VRF driver:
1. Rather than using the VRF device index and full FIB lookups,
packets to/from these addresses should use direct FIB lookups based on
the VRF device table.
2. fail sends/receives on a VRF device to/from a multicast address
(e.g, make ping6 ff02::1%<vrf> fail)
3. move the setting of the flow oif to the first dst lookup and revert
the change in icmpv6_echo_reply made in ca254490c8 ("net: Add VRF
support to IPv6 stack"). Linklocal/mcast addresses require use of the
skb->dev.
With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses work (icmp, tcp, and udp)
e.g.,
1. packets into VM with VRF config:
ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
ping6 -c3 ff02::1%br1
ssh -6 fe80::e0:f9ff:fe1c:b974%br1
2. packets going out a VRF enslaved device:
ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
ping6 -c3 ff02::1%eth1
ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In IPv6 the ToS values are part of the flowlabel in flowi6 and get
extracted during fib rule lookup, but we forgot to correctly initialize
the flowlabel before the routing lookup.
Reported-by: <liam.mcbirnie@boeing.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when creating or updating a route, no check is performed
in both ipv4 and ipv6 code to the hoplimit value.
The caller can i.e. set hoplimit to 256, and when such route will
be used, packets will be sent with hoplimit/ttl equal to 0.
This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4
ipv6 route code, substituting any value greater than 255 with 255.
This is consistent with what is currently done for ADVMSS and MTU
in the ipv4 code.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move l3mdev_rt6_dst_by_oif and l3mdev_get_saddr to l3mdev.c. Collapse
l3mdev_get_rt6_dst into l3mdev_rt6_dst_by_oif since it is the only
user and keep the l3mdev_get_rt6_dst name for consistency with other
hooks.
A follow-on patch adds more code to these functions making them long
for inlined functions.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to 3bfd847203 ("net: Use passed in table for nexthop lookups")
for IPv4, if the route spec contains a table id use that to lookup the
next hop first and fall back to a full lookup if it fails (per the fix
4c9bcd1179 ("net: Fix nexthop lookups")).
Example:
root@kenny:~# ip -6 ro ls table red
local 2100:1::1 dev lo proto none metric 0 pref medium
2100:1::/120 dev eth1 proto kernel metric 256 pref medium
local 2100:2::1 dev lo proto none metric 0 pref medium
2100:2::/120 dev eth2 proto kernel metric 256 pref medium
local fe80::e0:f9ff:fe09:3cac dev lo proto none metric 0 pref medium
local fe80::e0:f9ff:fe1c:b974 dev lo proto none metric 0 pref medium
fe80::/64 dev eth1 proto kernel metric 256 pref medium
fe80::/64 dev eth2 proto kernel metric 256 pref medium
ff00::/8 dev red metric 256 pref medium
ff00::/8 dev eth1 metric 256 pref medium
ff00::/8 dev eth2 metric 256 pref medium
unreachable default dev lo metric 240 error -113 pref medium
root@kenny:~# ip -6 ro add table red 2100:3::/64 via 2100:1::64
RTNETLINK answers: No route to host
Route add fails even though 2100:1::64 is a reachable next hop:
root@kenny:~# ping6 -I red 2100:1::64
ping6: Warning: source address might be selected on device other than red.
PING 2100:1::64(2100:1::64) from 2100:1::1 red: 56 data bytes
64 bytes from 2100:1::64: icmp_seq=1 ttl=64 time=1.33 ms
With this patch:
root@kenny:~# ip -6 ro add table red 2100:3::/64 via 2100:1::64
root@kenny:~# ip -6 ro ls table red
local 2100:1::1 dev lo proto none metric 0 pref medium
2100:1::/120 dev eth1 proto kernel metric 256 pref medium
local 2100:2::1 dev lo proto none metric 0 pref medium
2100:2::/120 dev eth2 proto kernel metric 256 pref medium
2100:3::/64 via 2100:1::64 dev eth1 metric 1024 pref medium
local fe80::e0:f9ff:fe09:3cac dev lo proto none metric 0 pref medium
local fe80::e0:f9ff:fe1c:b974 dev lo proto none metric 0 pref medium
fe80::/64 dev eth1 proto kernel metric 256 pref medium
fe80::/64 dev eth2 proto kernel metric 256 pref medium
ff00::/8 dev red metric 256 pref medium
ff00::/8 dev eth1 metric 256 pref medium
ff00::/8 dev eth2 metric 256 pref medium
unreachable default dev lo metric 240 error -113 pref medium
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a case in connected UDP socket such that
getsockopt(IPV6_MTU) will return a stale MTU value. The reproducible
sequence could be the following:
1. Create a connected UDP socket
2. Send some datagrams out
3. Receive a ICMPV6_PKT_TOOBIG
4. No new outgoing datagrams to trigger the sk_dst_check()
logic to update the sk->sk_dst_cache.
5. getsockopt(IPV6_MTU) returns the mtu from the invalid
sk->sk_dst_cache instead of the newly created RTF_CACHE clone.
This patch updates the sk->sk_dst_cache for a connected datagram sk
during pmtu-update code path.
Note that the sk->sk_v6_daddr is used to do the route lookup
instead of skb->data (i.e. iph). It is because a UDP socket can become
connected after sending out some datagrams in un-connected state. or
It can be connected multiple times to different destinations. Hence,
iph may not be related to where sk is currently connected to.
It is done under '!sock_owned_by_user(sk)' condition because
the user may make another ip6_datagram_connect() (i.e changing
the sk->sk_v6_daddr) while dst lookup is happening in the pmtu-update
code path.
For the sock_owned_by_user(sk) == true case, the next patch will
introduce a release_cb() which will update the sk->sk_dst_cache.
Test:
Server (Connected UDP Socket):
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Route Details:
[root@arch-fb-vm1 ~]# ip -6 r show | egrep '2fac'
2fac::/64 dev eth0 proto kernel metric 256 pref medium
2fac:face::/64 via 2fac::face dev eth0 metric 1024 pref medium
A simple python code to create a connected UDP socket:
import socket
import errno
HOST = '2fac::1'
PORT = 8080
s = socket.socket(socket.AF_INET6, socket.SOCK_DGRAM)
s.bind((HOST, PORT))
s.connect(('2fac:face::face', 53))
print("connected")
while True:
try:
data = s.recv(1024)
except socket.error as se:
if se.errno == errno.EMSGSIZE:
pmtu = s.getsockopt(41, 24)
print("PMTU:%d" % pmtu)
break
s.close()
Python program output after getting a ICMPV6_PKT_TOOBIG:
[root@arch-fb-vm1 ~]# python2 ~/devshare/kernel/tasks/fib6/udp-connect-53-8080.py
connected
PMTU:1300
Cache routes after recieving TOOBIG:
[root@arch-fb-vm1 ~]# ip -6 r show table cache
2fac:face::face via 2fac::face dev eth0 metric 0
cache expires 463sec mtu 1300 pref medium
Client (Send the ICMPV6_PKT_TOOBIG):
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
scapy is used to generate the TOOBIG message. Here is the scapy script I have
used:
>>> p=Ether(src='da:75:4d:36:ac:32', dst='52:54:00:12:34:66', type=0x86dd)/IPv6(src='2fac::face', dst='2fac::1')/ICMPv6PacketTooBig(mtu=1300)/IPv6(src='2fac::
1',dst='2fac:face::face', nh='UDP')/UDP(sport=8080,dport=53)
>>> sendp(p, iface='qemubr0')
Fixes: 45e4fd2668 ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reported-by: Wei Wang <weiwan@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivek reported a kernel exception deleting a VRF with an active
connection through it. The root cause is that the socket has a cached
reference to a dst that is destroyed. Converting the dst_destroy to
dst_release and letting proper reference counting kick in does not
work as the dst has a reference to the device which needs to be released
as well.
I talked to Hannes about this at netdev and he pointed out the ipv4 and
ipv6 dst handling has dst_ifdown for just this scenario. Rather than
continuing with the reinvented dst wheel in VRF just remove it and
leverage the ipv4 and ipv6 versions.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of ip6_dst_lookup_tail basically
ignore the egress ifindex match: if the saddr is set,
ip6_route_output() purposefully ignores flowi6_oif, due
to the commit d46a9d678e ("net: ipv6: Dont add RT6_LOOKUP_F_IFACE
flag if saddr set"), if the saddr is 'any' the first route lookup
in ip6_dst_lookup_tail fails, but upon failure a second lookup will
be performed with saddr set, thus ignoring the ifindex constraint.
This commit adds an output route lookup function variant, which
allows the caller to specify lookup flags, and modify
ip6_dst_lookup_tail() to enforce the ifindex match on the second
lookup via said helper.
ip6_route_output() becames now a static inline function build on
top of ip6_route_output_flags(); as a side effect, out-of-tree
modules need now a GPL license to access the output route lookup
functionality.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for adding expire value to routes, requested by
Tom Gundersen <teg@jklm.no> for systemd-networkd, and NetworkManager
wants it too.
implement it by adding the new RTNETLINK attribute RTA_EXPIRES.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ab450605b3.
In IPv6, we cannot inherit the dst of the original dst. ndisc packets
are IPv6 packets and may take another route than the original packet.
This patch breaks the following scenario: a packet comes from eth0 and
is forwarded through vxlan1. The encapsulated packet triggers an NS
which cannot be sent because of the wrong route.
CC: Jiri Benc <jbenc@redhat.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tracepoint to show fib6 table lookups and result.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All DST_NOCACHE rt6_info used to have rt->dst.from set to
its parent.
After commit 8e3d5be736 ("ipv6: Avoid double dst_free"),
DST_NOCACHE is also set to rt6_info which does not have
a parent (i.e. rt->dst.from is NULL).
This patch catches the rt->dst.from == NULL case.
Fixes: 8e3d5be736 ("ipv6: Avoid double dst_free")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the expires of the DST_NOCACHE rt can be set during
the ip6_rt_update_pmtu(), we also need to consider the expires
value when doing ip6_dst_check().
This patches creates __rt6_check_expired() to only
check the expire value (if one exists) of the current rt.
In rt6_dst_from_check(), it adds __rt6_check_expired() as
one of the condition check.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original bug report:
https://bugzilla.redhat.com/show_bug.cgi?id=1272571
The setup has a IPv4 GRE tunnel running in a IPSec. The bug
happens when ndisc starts sending router solicitation at the gre
interface. The simplified oops stack is like:
__lock_acquire+0x1b2/0x1c30
lock_acquire+0xb9/0x140
_raw_write_lock_bh+0x3f/0x50
__ip6_ins_rt+0x2e/0x60
ip6_ins_rt+0x49/0x50
~~~~~~~~
__ip6_rt_update_pmtu.part.54+0x145/0x250
ip6_rt_update_pmtu+0x2e/0x40
~~~~~~~~
ip_tunnel_xmit+0x1f1/0xf40
__gre_xmit+0x7a/0x90
ipgre_xmit+0x15a/0x220
dev_hard_start_xmit+0x2bd/0x480
__dev_queue_xmit+0x696/0x730
dev_queue_xmit+0x10/0x20
neigh_direct_output+0x11/0x20
ip6_finish_output2+0x21f/0x770
ip6_finish_output+0xa7/0x1d0
ip6_output+0x56/0x190
~~~~~~~~
ndisc_send_skb+0x1d9/0x400
ndisc_send_rs+0x88/0xc0
~~~~~~~~
The rt passed to ip6_rt_update_pmtu() is created by
icmp6_dst_alloc() and it is not managed by the fib6 tree,
so its rt6i_table == NULL. When __ip6_rt_update_pmtu() creates
a RTF_CACHE clone, the newly created clone also has rt6i_table == NULL
and it causes the ip6_ins_rt() oops.
During pmtu update, we only want to create a RTF_CACHE clone
from a rt which is currently managed (or owned) by the
fib6 tree. It means either rt->rt6i_node != NULL or
rt is a RTF_PCPU clone.
It is worth to note that rt6i_table may not be NULL even it is
not (yet) managed by the fib6 tree (e.g. addrconf_dst_alloc()).
Hence, rt6i_node is a better check instead of rt6i_table.
Fixes: 45e4fd2668 ("ipv6: Only create RTF_CACHE routes after encountering pmtu")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reported-by: Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu>
Cc: Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are other error values besides ip6_null_entry that can be returned by
ip6_route_redirect(): fib6_rule_action() can also result in
ip6_blk_hole_entry and ip6_prohibit_entry if such ip rules are installed.
Only checking for ip6_null_entry in rt6_do_redirect() causes ip6_ins_rt()
to be called with rt->rt6i_table == NULL in these cases, making the kernel
crash.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
741a11d9e4 ("net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set")
adds the RT6_LOOKUP_F_IFACE flag to make device index mismatch fatal if
oif is given. Hajime reported that this change breaks the Mobile IPv6
use case that wants to force the message through one interface yet use
the source address from another interface. Handle this case by only
adding the flag if oif is set and saddr is not set.
Fixes: 741a11d9e4 ("net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set")
Cc: Hajime Tazaki <thehajime@gmail.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6e28b00082 ("net: Fix vti use case with oif in dst lookups for IPv6")
is missing the checks on FLOWI_FLAG_SKIP_NH_OIF. Add them.
Fixes: 42a7b32b73 ("xfrm: Add oif to dst lookups")
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_blackhole_route() does not initialize the newly allocated
rt6_info properly. This patch:
1. Call rt6_info_init() to initialize rt6i_siblings and rt6i_uncached
2. The current rt->dst._metrics init code is incorrect:
- 'rt->dst._metrics = ort->dst._metris' is not always safe
- Not sure what dst_copy_metrics() is trying to do here
considering ip6_rt_blackhole_cow_metrics() always returns
NULL
Fix:
- Always do dst_copy_metrics()
- Replace ip6_rt_blackhole_cow_metrics() with
dst_cow_metrics_generic()
3. Mask out the RTF_PCPU bit from the newly allocated blackhole route.
This bug triggers an oops (reported by Phil Sutter) in rt6_get_cookie().
It is because RTF_PCPU is set while rt->dst.from is NULL.
Fixes: d52d3997f8 ("ipv6: Create percpu rt6_info")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reported-by: Phil Sutter <phil@nwl.cc>
Tested-by: Phil Sutter <phil@nwl.cc>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce rt6_info_init() to do the common init work for
'struct rt6_info' (after calling dst_alloc).
It is a prep work to fix the rt6_info init logic in the
ip6_blackhole_route().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with IPv4 support for VRFs added to IPv6 stack by replacing hardcoded
table ids with possibly device specific ones and manipulating the oif in
the flowi6. The flow flags are used to skip oif compare in nexthop lookups
if the device is enslaved to a VRF via the L3 master device.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As originally written rt6_uncached_list_flush_dev makes no sense when
called with dev == NULL as it attempts to flush all uncached routes
regardless of network namespace when dev == NULL. Which is simply
incorrect behavior.
Furthermore at the point rt6_ifdown is called with dev == NULL no more
network devices exist in the network namespace so even if the code in
rt6_uncached_list_flush_dev were to attempt something sensible it
would be meaningless.
Therefore remove support in rt6_uncached_list_flush_dev for handling
network devices where dev == NULL, and only call rt6_uncached_list_flush_dev
when rt6_ifdown is called with a network device.
Fixes: 8d0b94afdc ("ipv6: Keep track of DST_NOCACHE routes in case of iface down/unregister")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: Martin KaFai Lau <kafai@fb.com>
Tested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes ip6_route_info_create return err pointer instead of
returning the rt pointer by reference as suggested by Dave
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network namespace is already passed into dst_output pass it into
dst->output lwt->output and friends.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only __ip6_local_out_sk has callers so rename __ip6_local_out_sk
__ip6_local_out and remove the previous __ip6_local_out.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with the other similar methods in the kernel pass a
struct sock into the dst_ops .local_out method.
Simplifying the socket passing case is needed a prequel to passing a
struct net reference into .local_out.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern