Add mt76x2_init_device routine in order to reuse common pcie/usb mac80211
initialization code supporting mt76x2u based device
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to reuse them supporting mt76x2u based devices, move
mt76x2_wait_for_mac, wait_for_wpdma and mt76x2_channel_silent in
mt76x2.h
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
move mt76x2_fw_header and mt76x2_patch_header definitions in mcu.h in
order to reuse them in mt76x2u mcu related code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since MT_TXD_INFO, MT_MCU_MSG and MT_RX_FCE_INFO definitions are in
common between mt76x2u, mt76x2 and mt76x0u move them in dma.h in order
to reuse usb code supporting mt76x2u and mt76x0u based devices
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is different enough to justify a split.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We would like to allow other utlities to init msix and rx.
Put their declarations in a place accessible to other utilities.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If CONFIG_IPV6 is not enabled in the kernel, tcp.h is not included
implicitly from other header files, causing compilation errors. To
solve that, explicitly include it in tx-gen2.c.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There was a bunch of code to support gscan which has never been used.
Remove it all to cleanup and get rid of a lot of dead code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Balanced power save mode isn't supported in the fw for 22560 devices
yet. Configure the power save mode to CAM until it gets implemented.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit f2e66c8df0.
The firmware never implemented this, and they do not plan to.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The periphery can't be accessed before we set the
INIT_DONE bit which initializes the device.
A previous patch added a reconfiguration of the MSI-X
tables upon resume, but at that point in the flow,
INIT_DONE wasn't set. Since the reconfiguration of the
MSI-X tables require periphery access, it failed.
The difference between WoWLAN and without WoWLAN is that
in WoWLAN, iwl_trans_pcie_d3_suspend clears the INIT_DONE
without clearing the STATUS_DEVICE_ENABLED bit in the
software status. Because of that, the resume code thinks
that the device is enabled, but the INIT_DONE bit has been
cleared.
To fix this, don't reconfigure the MSI-X tables in case
WoWLAN is enabled. It will be done in
iwl_trans_pcie_d3_resume anyway.
Fixes: 52848a79b9 ("iwlwifi: pcie: reconfigure MSI-X HW on resume")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently multi-queue is disabled for 22000 devices.
This was since driver isn't supposed to write to prph
registers anymore, and FW needs to configure the RFH.
Now that FW added support for the API - use it and remove
the 22000 multi RX queue disablement.
Bump min API version to avoid compatibility issues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the firmware does not stop recording debugging data when
entering D3 and this causes trouble (e.g. sporadic wake ups).
Fix that by stopping dbg recording when suspending.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reading and dumping memory areas takes time, and sometimes
dumping all of the areas isn't necessary.
Allow choosing the memory areas which should be dumped.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Op mode will need this data in order to feed FW with it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes code less indented and more readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This allows less "dummy" declarations and casting.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices use a new rx_mpdu_desc api.
Update the code to use the new api.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The rfh for 22560 devices has changed so it supports now
the same arch of using used and free lists, but different
structures to support the last.
Use the new structures, hw dependent, to manage the lists.
bd, the free list, uses the iwl_rx_transfer_desc,
in which the vid is stored in the structs' rbid
field, and the page address in the addr field.
used_bd, the used list, uses the iwl_rx_completion_desc
struct, in which the vid is stored in the structs' rbid
field.
rb_stts, the hw "write" pointer of rx is stored in a
__le16 array, in which each entry represents the write
pointer per queue.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
HW requires Rx buffers to be 4 bytes aligned. Modify the driver to
meet this requirement.
Enable OFU rdy valid bug fix, to prevent hang in oful34_rx while
there is back-pressure from host during RX.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the driver doesn't support secured boot flow, hence
prevent FW download in case HW is configured for such a flow.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently wil6210 ignores the channel field in the
cfg80211_mgmt_tx_params struct for wil_cfg80211_ops mgmt_tx operation
and sends all management frames on the serving channel.
Add support for off-channel transmission of management frames
(WIPHY_FLAG_OFFCHAN_TX) in AP mode. This is useful in enterprise APs
for sending custom probe request frames.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Single MSI is the current default configuration.
With multiple MSI interrupts configuration, Tx/Rx processing could
run in parallel on different CPU cores and allow better balance
between the cores.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW file name for Talyn device can be different from the default name.
In such a case use a corresponding board file name.
If such a board file is not present FW download procedure will fail.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware ready event may take longer than
current timeout in some scenarios, for example
with multiple RFs connected where each
requires an initial calibration.
Increase the timeout to support these scenarios.
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW can support BACK window size 64 for performance improvements.
A new FW capability is added for notifying the host on the increased
max BACK win size support.
Defining WIL_MAX_AGG_WSIZE_64 and WIL_MAX_AMPDU_SIZE_128 to be used
in this case.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Scan is allowed only on client interfaces (STA/P2P).
Allow scan on AP interface so that the AP can discover rouge
or unauthorized neighbor APs.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver can request FW to report link statistics using
WMI_LINK_STATS_CMDID.
FW will report statistics with WMI_LINK_STATS_EVENTID.
Two categories of statistics defined: basic and global.
New "link_stats" debugfs is used for requesting basic statistics
report (write) and for reading the basic statistics (read).
"link_stats_global" debugfs is used for requesting and reading the
global statistics.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With some tool chains compilation fails due to type
mismatch of the arguments passed to min().
Use min_t() to solve these compilation errors.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extend MSI support to 3-MSI in order to load balance the tx\rx
interrupts between different cores.
use_msi module parameter has changed to n_msi. Usage:
- Set n_msi to 0 for using INTx
- Set n_msi to 1 for using single MSI
- Set n_msi to 3 for using 3-MSI
In 3-MSI configuration MSI 0 is used for TX interrupts, MSI 1
is used for RX interrupts and MSI 2 is used for MISC interrupts.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW file name for Talyn device is different from the default name.
This patch searches for Talyn specific FW file name and fallback
to the default FW file in case it is not present.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the driver sets CHECKSUM_UNNECESSARY only in case the HW
doesn't report checksum error.
As ip_summed value is not initialized it is not clear what
the driver will report to the network stack in case of HW checksum
error or in case HW doesn't calculate checksum.
Initialize ip_summed to CHECKSUM_NONE to guarantee checksum
calculation by the network stack in the above cases.
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For negative temperatures, "temp" debugfs is showing wrong values.
Use signed types so proper calculations is done for sub zero
temperatures.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Collect statistics of TX latency. The latency is measured from the time
the HW gets aware of new SKB to transmit until the HW indicates tx
complete for this SKB.
The statistics are shown via new "tx_latency" debugfs.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to recent change in FW, driver will be notified of corrupted Rx
packets (e.g. MIC error).
Drop such packets before they are delivered to network stack.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Store the last received multicast sequence number (SN) part of the TID
info. Drop Rx multicast packets with retry bit set which their SN
is equal to the last received.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The flag needs to be cleared for the last packet in the list, not the
first one. Fixes some issues with multicast packet loss for powersave
clients connected to an ath9k AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lower limits than the CTLs
of the user configured regdomain.
To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ensure that a buffer gets tracked as part of the block-ack window as
soon as it's dequeued from the tid for the first time. Ensure that
double calls to ath_tx_addto_baw (e.g. on retransmission) don't cause
any issues.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes missed indications of end of U-APSD service period to mac80211
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The checks already prevents periodic cal from being started while noise
floor calibration runs. It is missing checks for the other way around.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9002 code and the QCA AR9003+ reference code do the same.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath6kl_bmi_init() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The QCA4019 hw1.0 firmware 10.4-3.2.1-00050 and 10.4-3.5.3-00053 (and most
likely all other) seem to ignore the WMI_CHAN_FLAG_DFS flag during the
scan. This results in transmission (probe requests) on channels which are
not "available" for transmissions.
Since the firmware is closed source and nothing can be done from our side
to fix the problem in it, the driver has to work around this problem. The
WMI_CHAN_FLAG_PASSIVE seems to be interpreted by the firmware to not
scan actively on a channel unless an AP was detected on it. Simple probe
requests will then be transmitted by the STA on the channel.
ath10k must therefore also use this flag when it queues a radar channel for
scanning. This should reduce the chance of an active scan when the channel
might be "unusable" for transmissions.
Fixes: e8a50f8ba4 ("ath10k: introduce DFS implementation")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These were recently introduced and found by checkpatch:
drivers/net/wireless/ath/ath10k/mac.c:6118: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6121: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6124: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Only rt2800 subdriver of rt2x00 implement sta_add() and sta_remove(),
rt2x00mac_sta_add and rt2x00mac_sta_remove has no callers after
commit 9c87758cf0 ("rt2x00: call sta_add/remove directly in rt2800").
So can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8225se_rf_init() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This patch only replaces the mdelay() that has >20ms time to wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
probe_atmel_card() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When receiving a beacon or probe response, we should update the
boottime_ns field which is the timestamp the frame was received at.
(cf mac80211.h)
This fixes a scanning issue with Android since it relies on this
timestamp to determine when the AP has been seen for the last time
(via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wl1271_warning() already appends a \n to the format,
so adding one to the warning string gives empty lines in the log.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some features supported by firmware aren't advertised and there is no
way for a driver to query them. This includes e.g. monitor mode details.
Most firmwares support monitor interface but only the latest ones
/announce/ it with a "monitor" flag in the "cap" iovar. There isn't any
reliable detection method for older firmwares (BRCMF_C_MONITOR was tried
but "it only indicates the core part of the stack supports").
Similarly support for tagging monitor frames and building radiotap
headers can't be reliably detected for all firmwares.
This commit adds table that allows mapping features to firmware version.
It adds mappings for 43602a1 and 4366b1 firmwares from
linux-firmware.git. Both were confirmed to be passing monitor frames.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_PROC_FS isn't set, gcc warning this:
drivers/net/wireless/intersil/hostap/hostap_hw.c:2901:12: warning: ‘prism2_registers_proc_show’ defined but not used [-Wunused-function]
static int prism2_registers_proc_show(struct seq_file *m, void *v)
drivers/net/wireless/intersil/hostap/hostap_proc.c:16:12: warning: ‘prism2_debug_proc_show’ defined but not used [-Wunused-function]
static int prism2_debug_proc_show(struct seq_file *m, void *v)
^
drivers/net/wireless/intersil/hostap/hostap_proc.c:49:12: warning: ‘prism2_stats_proc_show’ defined but not used [-Wunused-function]
static int prism2_stats_proc_show(struct seq_file *m, void *v)
^
drivers/net/wireless/intersil/hostap/hostap_proc.c:177:12: warning: ‘prism2_crypt_proc_show’ defined but not used [-Wunused-function]
static int prism2_crypt_proc_show(struct seq_file *m, void *v)
^
fix this by adding #ifdef around them.
hfa384x_read_reg is only used by prism2_registers_proc_show,so move it
into #ifdef.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_PROC_FS isn't set, gcc warning this:
drivers/net/wireless/atmel/atmel.c:1402:12: warning: ‘atmel_proc_show’ defined but not used [-Wunused-function]
static int atmel_proc_show(struct seq_file *m, void *v)
^
fix this by adding #ifdef around it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer 'p' is being assigned but is never used hence it is
redundant and can be removed. Also re-work if statement to remove
redundant assignment of p.
Cleans up clang warning:
warning: variable 'p' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables id, unicast, write, conf, a_band, accum_tx and ucode are
assigned a value but it is never read, hence they are redundant and
can be removed.
Cleans up clang warnings:
warning: variable 'id' set but not used [-Wunused-but-set-variable]
warning: variable 'unicast' set but not used [-Wunused-but-set-variable]
warning: variable 'write' set but not used [-Wunused-but-set-variable]
warning: variable 'conf' set but not used [-Wunused-but-set-variable]
warning: variable 'a_band' set but not used [-Wunused-but-set-variable]
warning: variable 'tx' set but not used [-Wunused-but-set-variable]
warning: variable 'accum_tx' set but not used [-Wunused-but-set-variable]
warning: variable 'ucode' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables len, ret, reason and crypt are assigned values that
are never read, hence they are redundant and can be removed.
Note: For the variable ret, a return code is being assigned, but
this is not returned and 0 is currently being returned, I believe
this is OK.
Cleans up clang warnings:
warning: variable 'len' set but not used [-Wunused-but-set-variable]
variable 'ret' set but not used [-Wunused-but-set-variable]
warning: variable 'reason' set but not used [-Wunused-but-set-variable]
warning: variable 'crypt' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables len and dev assigned values but are never used hence they
are redundant and can be removed. Also add in white space in for-loop
and remove some { } braces on if statement.
Cleans up clang warnings:
warning: variable 'len' set but not used [-Wunused-but-set-variable]
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
common->init_done flag should set after basic initialization. Hence,
moving init_done flag at end of rsi_91x_init().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rx_params are getting updated two times in driver, which is not required.
Hence, removing duplicate updation of rx_params from rsi_prepare_skb().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, RSI_NEEDED_HEADROOM is '80' for rsi driver, which is wrong.
As per rsi internal frame format, the RSI_NEEDED_HEADROOM shall be '84',
which is 64(dword_align) + 4(extended_desc) + 16(frame_desc).
Hence, corrected the needed headroom.
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, AP mode will work on only WLAN alone firmware. To give support
for AP and BT dual mode, adding firmware entry in 'struct ta_metadata'.
The firmware entry is based on what coex_mode is used in driver and coex
mode '4' for all AP+BT related functionalities. Hence, added the same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
while cleaning up the driver, observed that flash_content pointer is not
necessary in rsi_load_firmware(). Instead of this, driver can use
'fw_entry->data' directly.Hence, removed redundant flash_content pointer.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removing redundant device id's from both usb and sdio idtables, as rsi
driver currently supporting only one module(RS9113). Also, replaced ids
with specific defines.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to multiple calls of add interface routine, vif is getting duplicated
and at certain instance, we are out of vifs, causing the driver to behave
abnormal.
Fix: Every vif has a unique mac-id, when we got a vif with same mac-id as
the previous id's, we will override the respective vif.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
System is unable to wake-up through magic-packet in secured connections.
Because key descriptor is getting corrupted and firmware is unable to
decrypt the magic packet. Fixed the issue by properly preparing it
before sending it to firmware.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Radio capabilities packet is not prepared properly for 40MHZ case,
ppe_ack_rate is a two byte variable which is initialized wrongly,
hence we are unable to connect, resolved by assigning it properly.
Signed-off-by: Ganapathi Raju <ganapathi.kondraju@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
observed low throughput rates during verification. This is because, QoS
enable flag is overridden by sequence number in the data descriptor frame.
Hence, added the fix for same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mwifiex firmware inserts only Microsoft information element
Allow other vendor specific IEs to pass from userspace
Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver is using boolean variables to maintain vairous status
information of adapter. These status variables are accessed by
multiple threads and there is a possibility of a race. To avoid
this, convert these variables to a set of bitops flags, to be
operated atomically.
Below variables of mwifiex_adapter are converted to bitop flags:
surprise_removed
is_cmd_timedout
is_suspended
is_hs_configured
hs_enabling
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver must ensure that whenever it holds a pointer to the list
entry mwifiex_rx_reorder_tbl, it must protect the same with
rx_reorder_tbl_lock. At present there are many places where
driver does not ensure this. To cover all cases, spinlocks in
below funcions are moved out and made sure that the caller will
hold the spinlock:
mwifiex_11n_dispatch_pkt_until_start_win()
mwifiex_11n_scan_and_dispatch()
mwifiex_del_rx_reorder_entry()
mwifiex_11n_get_rx_reorder_tbl()
mwifiex_11n_find_last_seq_num()
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At present driver spinlock protects iteration of list
rx_reorder_tbl_ptr with rx_reorder_tbl_lock. To protect the
individual items in this list, it uses rx_pkt_lock. But, we can
use a single rx_reorder_tbl_lock for both purposes. This patch
replaces rx_pkt_lock by rx_reorder_tbl_lock.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Debugfs support to do hardware warm reset with WMI command
WMI_PDEV_PARAM_PDEV_RESET for 10.4 and 10.2.4(if wmi
service is enabled in the firmware for backward compatibility).
This change is purely for debugging purpose when hardware hangs/mutes.
This hardware reset won't affect the connectivity but there will be small
pause in data traffic. Here we are doing BB/MAC level reset and hence
whenever the BB/MAC watchdog is triggered, it does a hardware_chip_reset.
So the target will be in the active state.
Below command used to warm reset the hardware.
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/warm_hw_reset
Tested in QCA988X with firmware ver 10.2.4.70.45
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only code refactoring as all call sites of
ath10k_htt_tx_alloc_msdu_id() take the same lock it can be moved into the
id_get function and the assertion dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables netlen, orig_buf, orig_len, dropped and stats are assigned values
but are never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'netlen' set but not used [-Wunused-but-set-variable]
warning: variable 'orig_buf' set but not used [-Wunused-but-set-variable]
warning: variable 'orig_len' set but not used [-Wunused-but-set-variable]
warning: variable 'dropped' set but not used [-Wunused-but-set-variable]
warning: variable 'stats' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer rf is being assigned but is never used hence it is redundant
and can be removed.
Cleans up two clang warnings:
warning: variable 'rf' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointers dev and noa are being assigned but are never used hence they
are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
warning: variable 'noa' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 transmits management frames via WMI
with reference. Currently, with the management
tx completion not being handled, these frames are
not getting freed even after the transmission status
is returned by the firmware.
The transmitted management frames should be freed
when the firmware sends the over-the-air tx status of
the corresponding management frames.
Handle the wmi mgmt tx completion event and free
the corresponding management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx completion of multiple mgmt frames can be bundled
in a single event and sent by the firmware to host, if this
capability is not disabled explicitly by the host. If the host
cannot handle the bundled mgmt tx completion, this capability
support needs to be disabled in the wmi init cmd, sent to the firmware.
Add the host capability indication flag in the wmi ready command,
to let firmware know the features supported by the host driver.
This field is ignored if it is not supported by firmware.
Set the host capability indication flag(i.e. host_capab) to zero,
for disabling the support of bundle mgmt tx completion. This will
indicate the firmware to send completion event for every mgmt tx
completion, instead of bundling them together and sending in a single
event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag. Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.
Tested on QCA9984 with firmware ver 10.4-3.6-00104
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes a recently added checkpatch warning:
wmi-tlv.c:2703: open brace '{' following function definitions go on the next line
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use 11M as tx rate for CCK protection control frames
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce mac80211 rts threshold handler in order to add frame
protection support to mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set MFP_CAPABLE bit in hw flag capabilities exported by the driver
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fall back to software encryption for hw unsupported ciphers in order
to enable 802.11w
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable support for multiple SSIDs scans. Get max number of supported
SSIDs from firmware and report to cfg80211 core.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement set_power_mgmt() callback that forwards power saving
settings to the device firmware.
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The smallest rb size supported today is 4k rx buffers.
22560 devices use 2k rxb's, so allow using 2k buffers.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22560 devices the firmware will do all the hw configurations,
but that's not ready yet.
Update the correct registers in the driver until the FW is ready
and does it by itself.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices RFH uses different structures, which act similar
to the legacy rxq management lists - free and used list.
The iwl_rx_transfer_desc struct is part of the free list,
and consists of pointers to the empty rb's the driver wants to
pass to the fw.
The iwl_rx_completion_desc struct is part of the used list,
and consists of pointers to the buffer the fw filled up
with new rx, both commands and data, for the host.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices use a new tx cmd api. Update the code to use
the new api.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices tfd queue max size is 2^16. Allow a configurable
max size in the driver for supporting different devices.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nowadays, the tfd queue max size is 2^8, and the reserved size in the
command header sequence field for the tfd entry index is 8 bits,
allowing an injective function from the hw pointers to the tfd entry index
in the sequence field.
In 22560 devices the tfd queue max size is 2^16, meaning that
the hw pointers are 16 bit long (allowing to point to each entry
in the tfd queue). However, the reserved space in the sequence field for
the tfd entry doesn't change, and we are limited to 8 bit.
This requires cancelling the injective function from hw pointer to
tfd entry in the sequence number.
Use iwl_pcie_get_cmd_index to wrap the hw pointer's to the n_window
size, which is maximum 256 in tx queues, and so, keep the injective
function between the window wrapped hw pointers to tfd entry index in
the sequence.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22560 devices the ROM sendis an interrupt to the host
once the IML reading is done.
Handle this interrupt, and indicate sw error in case the
value is fail.
Additionally, the cause for sw error in 22560 devices
have been changed, so update the cause list.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22560 devices we can start debug using context info gen3. Configure
the fw to start collecting logs to the dram before init.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Lorenzo Bianconi