mirror of https://gitee.com/openkylin/linux.git
160 Commits
| Author | SHA1 | Message | Date |
|---|---|---|---|
Lucas Stach
|
0136afa089 |
irqchip: Add driver for imx-irqsteer controller
The irqsteer block is a interrupt multiplexer/remapper found on the i.MX8 line of SoCs. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Richard Fitzgerald
|
da0abe1a04 |
irqchip: Add driver for Cirrus Logic Madera codecs
The Cirrus Logic Madera codecs (Cirrus Logic CS47L35/85/90/91 and WM1840) are highly complex devices containing up to 7 programmable DSPs and many other internal sources of interrupts plus a number of GPIOs that can be used as interrupt inputs. The large number (>150) of internal interrupt sources are managed by an on-board interrupt controller. This driver provides the handling for the interrupt controller. As the codec is accessed via regmap, we can make use of the generic IRQ functionality from regmap to do most of the work. Only around half of the possible interrupt source are currently of interest from the driver so only this subset is defined. Others can be added in future if needed. The KConfig options are not user-configurable because this driver is mandatory so is automatically included when the parent MFD driver is selected. Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Manivannan Sadhasivam
|
d852e62ad6 |
irqchip: Add RDA8810PL interrupt driver
Add interrupt driver for RDA Micro RDA8810PL SoC. Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Linus Torvalds
|
ac43507589 |
This tag contains the Linux port for C-SKY(csky) based on linux-4.19
Release, which has been through 10 rounds of review on mailing list. We almost got the Acked-by/Reviewed-by of all patches except "Process management and Signal", but all've been tested. Here is the LTP-20180118 test report: ----------------------------------------------- Total Tests: 1298 Total Skipped Tests: 281 Total Failures: 10 Kernel Version: 4.19.0+ Machine Architecture: csky Hostname: buildroot ----------------------------------------------- This patchset adds architecture support to Linux for C-SKY's 32-bit embedded There are two ABI versions with several CPU cores in this patchset: ABIv1: 610 (16-bit instruction, 32-bit data path, VIPT Cache ...) ABIv2: 807 810 860 (16/32-bit variable length instruction, PIPT Cache, SMP ...) More information: http://en.c-sky.com The development repo: https://github.com/c-sky/csky-linux ABI Documentation: https://github.com/c-sky/csky-doc Here is the pre-built cross compiler for fast test from our CI: https://gitlab.com/c-sky/buildroot/-/jobs/101608095/artifacts/file/output/images/csky_toolchain_qemu_csky_ck807f_4.18_glibc_defconfig_482b221e52908be1c9b2ccb444255e1562bb7025.tar.xz We use buildroot as our CI-test enviornment. "LTP, Lmbench ..." will be tested for every commit. See here for more details: https://gitlab.com/c-sky/buildroot/pipelines We'll continouslly improve csky subsystem in future. Changes in v10: - Remove duplicated headers in asm/Kbuild and uapi/asm/Kbuild. - Change to (__NR_arch_specific_syscall + 1) in unistd.h. - Drop dword access for get_user_size patch. - Involve the interrupt controller drivers after got Reviewed-by. Changes in v9: - Remove unused code in smp.c and use per_cpu for ipi_data. - Fixup r15 register access in abiv1/alignment.c. - Improve the changelog comment in commit-msg. Changes in v8: - Pass make allmodconfig. - Implement abiv1 get_user_dword(). - Remove set_irq_mapping() used by driver in smp.c. Changes in v7: - Use checkpatch.pl to check all patches and fixup as possible. - Remove github.com/c-sky print in bootup. - Give a return in DMA_ATTR_NON_CONSISTENT in csky_dma_alloc_atomic(). - Remove the NSIGXXX in fpu.c and use force_sig_fault() in fpu.c. - Remove irq.h and add it in asm/Kbuild. - Use byteswap helpers in abiv1/bswapXi.c. - Fixup arch_sync_dma() only with one page problem. Changes in v6: - use asm-generic/bitops/atomic.h for all in asm/bitops.h - fix flush_cache_range and tlb_start_vma - fix compile error with include linux/bug.h in cmpxchg.h - improve the comment Changes in v5: - remove redundant smp_mb operations in spinlock.h - add commit message for dt-bindings docs - add CPUHP_AP_CSKY_TIMER_STARTING in hotplug.h for csky_mptimer - add COMPILE_TEST for timer-gx6605s Kconfig - seperate csky two interrupt controllers with 2 patches - add MAINTAINERS patch for csky - move IPI_IRQ into csky_mptimer, fixup irq_mapping problem - coding convension Changes in v4: - cleanup defconfig - use ksys_ in syscall.c - remove wrong comment in vdso.c - Use GENERIC_IRQ_MULTI_HANDLER - optimize the memset.c - fixup dts warnings - remove big-endian in byteorder.h Changes in v3: dc560f1 csky: change to EM_CSKY 252 for elf.h 2ac3ddf csky: remove gx6605s.dts af00b8c csky: add defconfig and qemu.dts 6c87efb csky: remove the deprecate name. f6dda39 csky: add dt-bindings doc. d9f02a8 csky: remove KERNEL_VERSION in upstream branch 7bd663c csky: Use kernel/dma/noncoherent.c 1544c09 csky: bugfix emmc hang up LINS-976 e963271 csky: cleanup include/asm/Kbuild cd267ba csky: remove CSKY_DEBUG_INFO 78950da csky: remove dcache invalid. 13fe51d csky: remove csum_ipv6_magic(), use generic one. a7372db csky: bugfix CK810 access twice error. 1bb7c69 csky: bugfix add gcc asm memory for barrier. 5ea3257 csky: add -msoft-float instead of -mfloat-abi=soft. 38b037d csky: bugfix losing cache flush range. ab5e8c4 csky: Add ticket-spinlock and qrwlock support. c9aaec5 csky: rename cskyksyms.c to libgcc_ksyms.c 28c5e48 csky: avoid the MB on failure: trylock f929c97 csky: bugfix idly4 may cause exception. 09dc496 csky: Use GENERIC_ASHLDI3/ASHRDI3 etc 6ecc99d csky: optimize smp boot code. 16f50df csky: asm/bug.h simple implement. 0ba532a csky: csky asm/atomic.h added. df66947 csky: asm/compat.h added |
|
|
Guo Ren
|
edff1b4835 |
irqchip: add C-SKY APB bus interrupt controller
The driver is for C-SKY APB bus interrupt controller. It's a simple interrupt controller which use pending reg to detect the irq and use enable/disable reg to mask/unmask interrupt sources. A lot of SOCs based on C-SKY CPU use the interrupt controller as root controller. Signed-off-by: Guo Ren <ren_guo@c-sky.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> |
|
|
Guo Ren
|
d8a5f5f791 |
irqchip: add C-SKY SMP interrupt controller
The driver is for C-SKY SMP interrupt controller. It support 16 soft-irqs, 16 private-irqs, and 992 max external-irqs, a total of 1024 interrupts. C-SKY CPU 807/810/860 SMP/non-SMP could use it. Signed-off-by: Guo Ren <ren_guo@c-sky.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Miquel Raynal
|
61ce8d8d8a |
irqchip/irq-mvebu-sei: Add new driver for Marvell SEI
This is a cascaded interrupt controller in the AP806 GIC that collapses
SEIs (System Error Interrupt) coming from the AP and the CPs (through
the ICU).
The SEI handles up to 64 interrupts. The first 21 interrupts are wired
from the AP. The next 43 interrupts are from the CPs and are triggered
through MSI messages. To handle this complexity, the driver has to
declare to the upper layer: one IRQ domain for the wired interrupts,
one IRQ domain for the MSIs; and acts as a MSI controller ('parent')
by declaring an MSI domain.
Suggested-by: Haim Boot <hayim@marvell.com>
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
|
Christoph Hellwig
|
8237f8bc4f
|
irqchip: add a SiFive PLIC driver
Add a driver for the SiFive implementation of the RISC-V Platform Level Interrupt Controller (PLIC). The PLIC connects global interrupt sources to the local interrupt controller on each hart. This driver is based on the driver in the RISC-V tree from Palmer Dabbelt, but has been almost entirely rewritten since, and includes many fixes from Atish Patra. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Atish Patra <atish.patra@wdc.com> [Binding update by Palmer] Signed-off-by: Palmer Dabbelt <palmer@sifive.com> |
|
|
Marc Zyngier
|
505287525c |
irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller
GICv3 offers the possibility to signal SPIs using a pair of doorbells (SETPI, CLRSPI) under the name of Message Based Interrupts (MBI). They can be used as either traditional (edge) MSIs, or the more exotic level-triggered flavour. Let's implement support for platform MSI, which is the original intent for this feature. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Rob Herring <robh@kernel.org> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lkml.kernel.org/r/20180508121438.11301-8-marc.zyngier@arm.com |
|
|
Linus Torvalds
|
df34df483a |
Staging/IIO patches for 4.17-rc1
Here is the big set of Staging/IIO driver patches for 4.17-rc1. It is a lot, over 500 changes, but not huge by previous kernel release standards. We deleted more lines than we added again (27k added vs. 91k remvoed), thanks to finally being able to delete the IRDA drivers and networking code. We also deleted the ccree crypto driver, but that's coming back in through the crypto tree to you, in a much cleaned-up form. Added this round is at lot of "mt7621" device support, which is for an embedded device that Neil Brown cares about, and of course a handful of new IIO drivers as well. And finally, the fsl-mc core code moved out of the staging tree to the "real" part of the kernel, which is nice to see happen as well. Full details are in the shortlog, which has all of the tiny cleanup patches described. All of these have been in linux-next for a while with no reported issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSnAA8cZ3JlZ0Brcm9h aC5jb20ACgkQMUfUDdst+yn60ACgxKvU/5XBP14hBkBpAcD0Q43OHe0AniEti65M Kw03GWK3NNM3pzk49BjZ =sj3K -----END PGP SIGNATURE----- Merge tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging/IIO updates from Greg KH: "Here is the big set of Staging/IIO driver patches for 4.17-rc1. It is a lot, over 500 changes, but not huge by previous kernel release standards. We deleted more lines than we added again (27k added vs. 91k remvoed), thanks to finally being able to delete the IRDA drivers and networking code. We also deleted the ccree crypto driver, but that's coming back in through the crypto tree to you, in a much cleaned-up form. Added this round is at lot of "mt7621" device support, which is for an embedded device that Neil Brown cares about, and of course a handful of new IIO drivers as well. And finally, the fsl-mc core code moved out of the staging tree to the "real" part of the kernel, which is nice to see happen as well. Full details are in the shortlog, which has all of the tiny cleanup patches described. All of these have been in linux-next for a while with no reported issues" * tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (579 commits) staging: rtl8723bs: Remove yield call, replace with cond_resched() staging: rtl8723bs: Replace yield() call with cond_resched() staging: rtl8723bs: Remove unecessary newlines from 'odm.h'. staging: rtl8723bs: Rework 'struct _ODM_Phy_Status_Info_' coding style. staging: rtl8723bs: Rework 'struct _ODM_Per_Pkt_Info_' coding style. staging: rtl8723bs: Replace NULL pointer comparison with '!'. staging: rtl8723bs: Factor out rtl8723bs_recv_tasklet() sections. staging: rtl8723bs: Fix function signature that goes over 80 characters. staging: rtl8723bs: Fix lines too long in update_recvframe_attrib(). staging: rtl8723bs: Remove unnecessary blank lines in 'rtl8723bs_recv.c'. staging: rtl8723bs: Change camel case to snake case in 'rtl8723bs_recv.c'. staging: rtl8723bs: Add missing braces in else statement. staging: rtl8723bs: Add spaces around ternary operators. staging: rtl8723bs: Fix lines with trailing open parentheses. staging: rtl8723bs: Remove unnecessary length #define's. staging: rtl8723bs: Fix IEEE80211 authentication algorithm constants. staging: rtl8723bs: Fix alignment in rtw_wx_set_auth(). staging: rtl8723bs: Remove braces from single statement conditionals. staging: rtl8723bs: Remove unecessary braces from switch statement. staging: rtl8723bs: Fix newlines in rtw_wx_set_auth(). ... |
|
|
Linus Torvalds
|
5b1f3dc927 |
Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The usual pile of boring changes:
- Consolidate tasklet functions to share code instead of duplicating
it
- The first step for making the low level entry handler management on
multi-platform kernels generic
- A new sysfs file which allows to retrieve the wakeup state of
interrupts.
- Ensure that the interrupt thread follows the effective affinity and
not the programmed affinity to avoid cross core wakeups.
- Two new interrupt controller drivers (Microsemi Ocelot and Qualcomm
PDC)
- Fix the wakeup path clock handling for Reneasas interrupt chips.
- Rework the boot time register reset for ARM GIC-V2/3
- Better suspend/resume support for ARM GIV-V3/ITS
- Add missing locking to the ARM GIC set_type() callback
- Small fixes for the irq simulator code
- SPDX identifiers for the irq core code and removal of boiler plate
- Small cleanups all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
openrisc: Set CONFIG_MULTI_IRQ_HANDLER
arm64: Set CONFIG_MULTI_IRQ_HANDLER
genirq: Make GENERIC_IRQ_MULTI_HANDLER depend on !MULTI_IRQ_HANDLER
irqchip/gic: Take lock when updating irq type
irqchip/gic: Update supports_deactivate static key to modern api
irqchip/gic-v3: Ensure GICR_CTLR.EnableLPI=0 is observed before enabling
irqchip: Add a driver for the Microsemi Ocelot controller
dt-bindings: interrupt-controller: Add binding for the Microsemi Ocelot interrupt controller
irqchip/gic-v3: Probe for SCR_EL3 being clear before resetting AP0Rn
irqchip/gic-v3: Don't try to reset AP0Rn
irqchip/gic-v3: Do not check trigger configuration of partitionned LPIs
genirq: Remove license boilerplate/references
genirq: Add missing SPDX identifiers
genirq/matrix: Cleanup SPDX identifier
genirq: Cleanup top of file comments
genirq: Pass desc to __irq_free instead of irq number
irqchip/gic-v3: Loudly complain about the use of IRQ_TYPE_NONE
irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE
RISC-V: Move to the new GENERIC_IRQ_MULTI_HANDLER handler
genirq: Add CONFIG_GENERIC_IRQ_MULTI_HANDLER
...
|
|
|
Linus Torvalds
|
f5a8eb632b |
arch: remove obsolete architecture ports
This removes the entire architecture code for blackfin, cris, frv, m32r, metag, mn10300, score, and tile, including the associated device drivers. I have been working with the (former) maintainers for each one to ensure that my interpretation was right and the code is definitely unused in mainline kernels. Many had fond memories of working on the respective ports to start with and getting them included in upstream, but also saw no point in keeping the port alive without any users. In the end, it seems that while the eight architectures are extremely different, they all suffered the same fate: There was one company in charge of an SoC line, a CPU microarchitecture and a software ecosystem, which was more costly than licensing newer off-the-shelf CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems that all the SoC product lines are still around, but have not used the custom CPU architectures for several years at this point. In contrast, CPU instruction sets that remain popular and have actively maintained kernel ports tend to all be used across multiple licensees. The removal came out of a discussion that is now documented at https://lwn.net/Articles/748074/. Unlike the original plans, I'm not marking any ports as deprecated but remove them all at once after I made sure that they are all unused. Some architectures (notably tile, mn10300, and blackfin) are still being shipped in products with old kernels, but those products will never be updated to newer kernel releases. After this series, we still have a few architectures without mainline gcc support: - unicore32 and hexagon both have very outdated gcc releases, but the maintainers promised to work on providing something newer. At least in case of hexagon, this will only be llvm, not gcc. - openrisc, risc-v and nds32 are still in the process of finishing their support or getting it added to mainline gcc in the first place. They all have patched gcc-7.3 ports that work to some degree, but complete upstream support won't happen before gcc-8.1. Csky posted their first kernel patch set last week, their situation will be similar. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJawdL2AAoJEGCrR//JCVInuH0P/RJAZh1nTD+TR34ZhJq2TBoo PgygwDU7Z2+tQVU+EZ453Gywz9/NMRFk1RWAZqrLix4ZtyIMvC6A1qfT2yH1Y7Fb Qh6tccQeLe4ezq5u4S/46R/fQXu3Txr92yVwzJJUuPyU0arF9rv5MmI8e6p7L1en yb74kSEaCe+/eMlsEj1Cc1dgthDNXGKIURHkRsILoweysCpesjiTg4qDcL+yTibV FP2wjVbniKESMKS6qL71tiT5sexvLsLwMNcGiHPj94qCIQuI7DLhLdBVsL5Su6gI sbtgv0dsq4auRYAbQdMaH1hFvu6WptsuttIbOMnz2Yegi2z28H8uVXkbk2WVLbqG ZESUwutGh8MzOL2RJ4jyyQq5sfo++CRGlfKjr6ImZRv03dv0pe/W85062cK5cKNs cgDDJjGRorOXW7dyU6jG2gRqODOQBObIv3w5efdq5OgzOWlbI4EC+Y5u1Z0JF/76 pSwtGXA6YhwC+9LLAlnVTHG+yOwuLmAICgoKcTbzTVDKA2YQZG/cYuQfI5S1wD8e X6urPx3Md2GCwLXQ9mzKBzKZUpu/Tuhx0NvwF4qVxy6x1PELjn68zuP7abDHr46r 57/09ooVN+iXXnEGMtQVS/OPvYHSa2NgTSZz6Y86lCRbZmUOOlK31RDNlMvYNA+s 3iIVHovno/JuJnTOE8LY =fQ8z -----END PGP SIGNATURE----- Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic Pul removal of obsolete architecture ports from Arnd Bergmann: "This removes the entire architecture code for blackfin, cris, frv, m32r, metag, mn10300, score, and tile, including the associated device drivers. I have been working with the (former) maintainers for each one to ensure that my interpretation was right and the code is definitely unused in mainline kernels. Many had fond memories of working on the respective ports to start with and getting them included in upstream, but also saw no point in keeping the port alive without any users. In the end, it seems that while the eight architectures are extremely different, they all suffered the same fate: There was one company in charge of an SoC line, a CPU microarchitecture and a software ecosystem, which was more costly than licensing newer off-the-shelf CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems that all the SoC product lines are still around, but have not used the custom CPU architectures for several years at this point. In contrast, CPU instruction sets that remain popular and have actively maintained kernel ports tend to all be used across multiple licensees. [ See the new nds32 port merged in the previous commit for the next generation of "one company in charge of an SoC line, a CPU microarchitecture and a software ecosystem" - Linus ] The removal came out of a discussion that is now documented at https://lwn.net/Articles/748074/. Unlike the original plans, I'm not marking any ports as deprecated but remove them all at once after I made sure that they are all unused. Some architectures (notably tile, mn10300, and blackfin) are still being shipped in products with old kernels, but those products will never be updated to newer kernel releases. After this series, we still have a few architectures without mainline gcc support: - unicore32 and hexagon both have very outdated gcc releases, but the maintainers promised to work on providing something newer. At least in case of hexagon, this will only be llvm, not gcc. - openrisc, risc-v and nds32 are still in the process of finishing their support or getting it added to mainline gcc in the first place. They all have patched gcc-7.3 ports that work to some degree, but complete upstream support won't happen before gcc-8.1. Csky posted their first kernel patch set last week, their situation will be similar [ Palmer Dabbelt points out that RISC-V support is in mainline gcc since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]" This really says it all: 2498 files changed, 95 insertions(+), 467668 deletions(-) * tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits) MAINTAINERS: UNICORE32: Change email account staging: iio: remove iio-trig-bfin-timer driver tty: hvc: remove tile driver tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers serial: remove tile uart driver serial: remove m32r_sio driver serial: remove blackfin drivers serial: remove cris/etrax uart drivers usb: Remove Blackfin references in USB support usb: isp1362: remove blackfin arch glue usb: musb: remove blackfin port usb: host: remove tilegx platform glue pwm: remove pwm-bfin driver i2c: remove bfin-twi driver spi: remove blackfin related host drivers watchdog: remove bfin_wdt driver can: remove bfin_can driver mmc: remove bfin_sdh driver input: misc: remove blackfin rotary driver input: keyboard: remove bf54x driver ... |
|
|
Alexandre Belloni
|
19d9916448 |
irqchip: Add a driver for the Microsemi Ocelot controller
The Microsemi Ocelot SoC has a pretty simple IRQ controller in its ICPU block. Add a driver for it. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Archana Sathyakumar
|
f55c73aef8 |
irqchip/pdc: Add PDC interrupt controller for QCOM SoCs
The Power Domain Controller (PDC) on QTI SoCs like SDM845 houses an interrupt controller along with other domain control functions to handle interrupt related functions like handle falling edge or active low which are not detected at the GIC and handle wakeup interrupts. The interrupt controller is on an always-on domain for the purpose of waking up the processor. Only a subset of the processor's interrupts are routed through the PDC to the GIC. The PDC powers on the processors' domain, when in low power mode and replays pending interrupts so the GIC may wake up the processor. Signed-off-by: Archana Sathyakumar <asathyak@codeaurora.org> Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
James Hogan
|
df46bb1909
|
irqchip: Remove metag irqchip drivers
Now that arch/metag/ has been removed, remove the two metag irqchip drivers. They are of no value without the architecture code. - irq-metag: Meta internal (HWSTATMETA) interrupt code. - irq-metag-ext: Meta External interrupt code. Signed-off-by: James Hogan <jhogan@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-metag@vger.kernel.org |
|
|
Bogdan Purcareata
|
7afe031c1a |
staging: fsl-mc: Move irqchip code out of staging
Now that the fsl-mc bus core infrastructure is out of staging, the remaining irqchip glue code used (irq-gic-v3-its-fsl-mc-msi.c) goes to drivers/irqchip. Create new Kconfig option for irqchip code that depends on FSL_MC_BUS and ARM_GIC_V3_ITS. This ensures irqchip code only gets built on ARM64 platforms. We can now remove #ifdef GENERIC_MSI_DOMAIN_OPS as it was only needed for x86. Signed-off-by: Stuart Yoder <stuyoder@gmail.com> [rebased, add dpaa2_eth and dpio #include updates] Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> [rebased, split irqchip to separate patch] Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com> [add Kconfig dependency on ARM_GIC_V3_ITS] Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
|
|
Greentime Hu
|
abe45fd9f1 |
irqchip: Andestech Internal Vector Interrupt Controller driver
This patch adds the Andestech Internal Vector Interrupt Controller driver. You can find the spec here. Ch4.9 of AndeStar SPA V3 Manual. http://www.andestech.com/product.php?cls=9 Signed-off-by: Rick Chen <rick@andestech.com> Signed-off-by: Greentime Hu <greentime@andestech.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Miodrag Dinic
|
4235ff50cf |
irqchip/irq-goldfish-pic: Add Goldfish PIC driver
Add device driver for a virtual programmable interrupt controller The virtual PIC is designed as a device tree-based interrupt controller. The compatible string used by OS for binding the driver is "google,goldfish-pic". Signed-off-by: Miodrag Dinic <miodrag.dinic@mips.com> Signed-off-by: Goran Ferenc <goran.ferenc@mips.com> Signed-off-by: Aleksandar Markovic <aleksandar.markovic@mips.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Thomas Gleixner
|
41cc30412d |
irqchip updates for 4.15, take #4
- A core irq fix for legacy cases where the irq trigger is not reported by firmware - A couple of GICv3/4 fixes (Kconfig, of-node refcount, error handling) - Trivial pr_err fixes -----BEGIN PGP SIGNATURE----- iQJJBAABCAAzFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAloJ2UYVHG1hcmMuenlu Z2llckBhcm0uY29tAAoJECPQ0LrRPXpDtkcP/i2HrgT5CmoA315h5HLXfFImxZwg YG7ti3zqu1TM7HXNlfBgSltqiU5UgYOd2KjgUR+w30t1239DwxVdtoy6ZgGWXlfe xmHlXAiEDkqaAV3P/RHKkl8xRDkyWhKmfY1ym/So0J68EPytuiZiT4wJZO39u/xk Gi2fW38gywl4bEb9MA48noEnkNkr93DjJfFyiPxPYiAaWeFRoP+X5l171kTpCdSv sT5hfQvfsz7mQZVecMBwGg6QuWnlUplkzPb4lNhuk/tJTU97vf3Py8abzeiGqBMa 5NoH9PUMZs0L8kv6DgR2DEOmhmmk0+mwO7VWVT3eVtYoxSS8oW0i2OzgB9kCOy8+ LZi+M0fMSL6hiAgwlV5YrHYvsVl2rGjCNAqC+q2ggpW4XH9Kql2caki331mGqAyr qDeI0SWaABz5c9ajtsfQ78T0FE70xwIJ5TT1RmtKt2LFCpJjBacjK3vUST2ypIrF k0AJTmBwEefKNvxTrjkZtenblCVo92lT+boAv7HuI612NicVSBEsK7S+96kGlGMw KNi+cwGriJRWIbsn+VMpLFGyPgEmWQ1p/4Z/tkwSevqOl/k8KrNw6+VoyDS1PmJU gIQ0hh8wMnm2l9VGJARc0+pHKr0KYN52j+jZI5+OGNKKAZ0jGYI4t2JiemtOwmet q2KNdm6mvBYUYirj =/8DQ -----END PGP SIGNATURE----- Merge tag 'irqchip-4.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent Pull irqchip updates for 4.15, take #4 from Marc Zyngier - A core irq fix for legacy cases where the irq trigger is not reported by firmware - A couple of GICv3/4 fixes (Kconfig, of-node refcount, error handling) - Trivial pr_err fixes |
|
|
Linus Torvalds
|
670310dfba |
Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
|
|
|
Linus Torvalds
|
f3573b8f90 |
OpenRISC updates for v4.15
Small Things:
- Move OpenRISC docs into Documentation and clean them up
- Document previously undocumented devicetree bindings
- Update the or1ksim dts to use stdout-path
OpenRISC SMP support details:
- First the "use shadow registers" and "define CPU_BIG_ENDIAN as true"
get the architecture ready for SMP.
- The "add 1 and 2 byte cmpxchg support" and "use qspinlocks and
qrwlocks" add the SMP locking infrastructure as needed. Using the
qspinlocks and qrwlocks as suggested by Peter Z while reviewing the
original spinlocks implementation.
- The "support for ompic" adds a new irqchip device which is used for
IPI communication to support SMP.
- The "initial SMP support" adds smp.c and makes changes to all of the
necessary data-structures to be per-cpu.
- The remaining patches are bug fixes and debug helpers which I wanted
to keep separate from the "initial SMP support" in order to allow them
to be reviewed on their own. This includes:
- add cacheflush support to fix icache aliasing
- fix initial preempt state for secondary cpu tasks
- sleep instead of spin on secondary wait
- support framepointers and STACKTRACE_SUPPORT
- enable LOCKDEP_SUPPORT and irqflags tracing
- timer sync: Add tick timer sync logic
- fix possible deadlock in timer sync, pointed out by mips guys
Note: the irqchip patch was reviewed with Marc and we agreed to push it
together with these patches.
-----BEGIN PGP SIGNATURE-----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=euP7
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/openrisc/linux
Pull OpenRISC updates from Stafford Horne:
"The OpenRISC work is a bit more interesting this time, adding SMP
support and a few general cleanups.
Small Things:
- Move OpenRISC docs into Documentation and clean them up
- Document previously undocumented devicetree bindings
- Update the or1ksim dts to use stdout-path
OpenRISC SMP support details:
- First the "use shadow registers" and "define CPU_BIG_ENDIAN as
true" get the architecture ready for SMP.
- The "add 1 and 2 byte cmpxchg support" and "use qspinlocks and
qrwlocks" add the SMP locking infrastructure as needed. Using the
qspinlocks and qrwlocks as suggested by Peter Z while reviewing the
original spinlocks implementation.
- The "support for ompic" adds a new irqchip device which is used for
IPI communication to support SMP.
- The "initial SMP support" adds smp.c and makes changes to all of
the necessary data-structures to be per-cpu.
The remaining patches are bug fixes and debug helpers which I wanted
to keep separate from the "initial SMP support" in order to allow them
to be reviewed on their own. This includes:
- add cacheflush support to fix icache aliasing
- fix initial preempt state for secondary cpu tasks
- sleep instead of spin on secondary wait
- support framepointers and STACKTRACE_SUPPORT
- enable LOCKDEP_SUPPORT and irqflags tracing
- timer sync: Add tick timer sync logic
- fix possible deadlock in timer sync, pointed out by mips guys
Note: the irqchip patch was reviewed with Marc and we agreed to push
it together with these patches"
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: fix possible deadlock scenario during timer sync
openrisc: pass endianness info to sparse
openrisc: add tick timer multi-core sync logic
openrisc: enable LOCKDEP_SUPPORT and irqflags tracing
openrisc: support framepointers and STACKTRACE_SUPPORT
openrisc: add simple_smp dts and defconfig for simulators
openrisc: add cacheflush support to fix icache aliasing
openrisc: sleep instead of spin on secondary wait
openrisc: fix initial preempt state for secondary cpu tasks
openrisc: initial SMP support
irqchip: add initial support for ompic
dt-bindings: add openrisc to vendor prefixes list
openrisc: use qspinlocks and qrwlocks
openrisc: add 1 and 2 byte cmpxchg support
openrisc: use shadow registers to save regs on exception
dt-bindings: openrisc: Add OpenRISC platform SoC
Documentation: openrisc: Updates to README
Documentation: Move OpenRISC docs out of arch/
MAINTAINERS: Add OpenRISC pic maintainer
openrisc: dts: or1ksim: Add stdout-path
|
|
|
Marc Zyngier
|
29f411399a |
irqchip/gic-v3-its: Remove artificial dependency on PCI
The GICv3 ITS doesn't really depend on PCI. Only the PCI/MSI
part of it does, and there is no reason not to blow away most
of the irqchip stack because PCI is not selected (though not
selecting PCI seem to be asking for punishment, but hey...).
So let's split the PCI-specific part from the ITS in the Kconfig
file, and let's make that part depend on PCI. Architecture specific
hacks (arch/arm{,64}/Kconfig) will be addressed in a separate patch.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
|
Ard Biesheuvel
|
706cffc1b9 |
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
The Socionext Synquacer SoC has an external interrupt unit (EXIU) that forwards a block of 32 configurable input lines to 32 adjacent level-high type GICv3 SPIs. The EXIU has per-interrupt level/edge and polarity controls, and mask bits that keep the outgoing lines de-asserted, even though the controller may still latch interrupt conditions that occur while the line is masked. Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Stafford Horne
|
9b54470afd |
irqchip: add initial support for ompic
IPI driver for the Open Multi-Processor Interrupt Controller (ompic) as described in the Multi-core support section of the OpenRISC 1.2 architecture specification: https://github.com/openrisc/doc/raw/master/openrisc-arch-1.2-rev0.pdf Each OpenRISC core contains a full interrupt controller which is used in the SMP architecture for interrupt balancing. This IPI device, the ompic, is the only external device required for enabling SMP on OpenRISC. Pending ops are stored in a memory bit mask which can allow multiple pending operations to be set and serviced at a time. This is mostly borrowed from the alpha IPI implementation. Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> [shorne@gmail.com: converted ops to bitmask, wrote commit message] Signed-off-by: Stafford Horne <shorne@gmail.com> |
|
|
Greg Kroah-Hartman
|
b24413180f |
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
|
|
Jerome Brunet
|
215f4cc0fb |
irqchip/meson: Add support for gpio interrupt controller
Add support for the interrupt gpio controller found on Amlogic's meson SoC family. This controller is a separate controller from the gpio controller. It is able to spy on the SoC pad. It is essentially a 256 to 8 router with a filtering block to select level or edge and polarity. The number of actual mappable inputs depends on the SoC. Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Marc Zyngier
|
3d63cb53e2 |
irqchip/gic-v4: Enable low-level GICv4 operations
Get the show on the road... Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Masahiro Yamada
|
5ed34d3a43 |
irqchip: Add UniPhier AIDET irqchip driver
UniPhier SoCs contain AIDET (ARM Interrupt Detector). This is intended to provide additional features that are not covered by GIC. The main purpose is to provide logic inverter to support low level and falling edge trigger types for interrupt lines from on-board devices. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Thomas Petazzoni
|
e0de91a977 |
irqchip/irq-mvebu-icu: Add new driver for Marvell ICU
The Marvell ICU unit is found in the CP110 block of the Marvell Armada 7K and 8K SoCs. It collects the wired interrupts of the devices located in the CP110 and turns them into SPI interrupts in the GIC located in the AP806 side of the SoC, by using a memory transaction. Until now, the ICU was configured in a static fashion by the firmware, and Linux was relying on this static configuration. By having Linux configure the ICU, we are more flexible, and we can allocate dynamically the GIC SPI interrupts only for devices that are actually in use. The driver was initially written by Hanna Hawa <hannah@marvell.com>. Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Thomas Petazzoni
|
a68a63cb4d |
irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP
This commit adds a simple driver for the Marvell GICP, a hardware unit that converts memory writes into GIC SPI interrupts. The driver provides a number of functions to the ICU driver to allocate GICP interrupts, and get the physical addresses that the ICUs should write to to set/clear interrupts. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Brendan Higgins
|
f48e699ddf |
irqchip/aspeed-i2c-ic: Add I2C IRQ controller for Aspeed
The Aspeed 24XX/25XX chips share a single hardware interrupt across 14 separate I2C busses. This adds a dummy irqchip which maps the single hardware interrupt to software interrupts for each of the busses. Signed-off-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Youlin Pei
|
9dbbbd33aa |
irqchip: Add Mediatek mtk-cirq driver
In Mediatek SOCs, the CIRQ is a low power interrupt controller designed to works outside MCUSYS which comprises with Cortex-Ax cores,CCI and GIC. The CIRQ controller is integrated in between MCUSYS( include Cortex-Ax, CCI and GIC ) and interrupt sources as the second level interrupt controller. The external interrupts which outside MCUSYS will feed through CIRQ then bypass to GIC. CIRQ can monitors all edge trigger interupts. When an edge interrupt is triggered, CIRQ can record the status and generate a pulse signal to GIC when flush command executed. When system enters sleep mode, MCUSYS will be turned off to improve power consumption, also GIC is power down. The edge trigger interrupts will be lost in this scenario without CIRQ. This commit provides the CIRQ irqchip implement. Signed-off-by: Youlin Pei <youlin.pei@mediatek.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Linus Walleij
|
390d2d490b |
irqchip/faraday: Replace moxa with ftintc010
The Moxa Art interrupt controller is very very likely just an instance of the Faraday FTINTC010 interrupt controller from Faraday Technology. An indication would be its close association with the FA526 ARM core and the fact that the register layout is the same. The implementation in irq-moxart.c can probably be right off replaced with the irq-ftintc010.c driver by adding a compatible string, selecting this irqchip from the machine and run. As a bonus we have an irqchip driver supporting high/low and rising/falling edges for the Moxa Art, and shared code with the Gemini platform. Acked-by: Olof Johansson <olof@lixom.net> Tested-by: Jonas Jensen <jonas.jensen@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Linus Walleij
|
6ee532e2fa |
irqchip/gemini: Refactor Gemini driver to reflect Faraday origin
The Gemini irqchip turns out to be a standard IP component from Faraday Technology named FTINTC010 after some research and new information. - Rename the driver and all symbols to reflect the new information. - Add the new compatible string "faraday,ftintc010" - Create a Kconfig symbol CONFIG_FARADAY_FTINTC010 so that SoCs using this interrupt controller can easily select and reuse it instead of hardwiring it to ARCH_GEMINI I have created a separate patch to select the new Kconfig symbol from the Gemini machine, which will be merged through the ARM SoC tree. Cc: Greentime Hu <green.hu@gmail.com> Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Linus Walleij
|
b4d3053c8c |
irqchip: Add a driver for Cortina Gemini
As a part of transitioning the Gemini platform to device tree we create this clean, device-tree-only irqchip driver. Cc: Janos Laube <janos.dev@gmail.com> Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com> Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Agustin Vega-Frias
|
f20cc9b00c |
irqchip/qcom: Add IRQ combiner driver
Driver for interrupt combiners in the Top-level Control and Status Registers (TCSR) hardware block in Qualcomm Technologies chips. An interrupt combiner in this block combines a set of interrupts by OR'ing the individual interrupt signals into a summary interrupt signal routed to a parent interrupt controller, and provides read- only, 32-bit registers to query the status of individual interrupts. The status bit for IRQ n is bit (n % 32) within register (n / 32) of the given combiner. Thus, each combiner can be described as a set of register offsets and the number of IRQs managed. Signed-off-by: Agustin Vega-Frias <agustinv@codeaurora.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Zubair Lutfullah Kakakhel
|
0547dc7885 |
microblaze/irqchip: Move intc driver to irqchip
The Xilinx AXI Interrupt Controller IP block is used by the MIPS based xilfpga platform and a few PowerPC based platforms. Move the interrupt controller code out of arch/microblaze so that it can be used by everyone Tested-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Linus Torvalds
|
a771151a83 |
ARM: SoC cleanups for v4.9
The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion
of old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files.
If no regressions are found, another large cleanup for the platform
will happen as a follow-up, removing dead code and restructuring
the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now DT-only.
The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT
in principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress.
We can probably merge the remaining code into a single directory
in the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then.
Conflicts: two files deleted here have been modified upstream,
the changes can be discarded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WaLy
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion of
old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files. If no regressions are found, another
large cleanup for the platform will happen as a follow-up, removing
dead code and restructuring the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now
DT-only. The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT in
principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress. We
can probably merge the remaining code into a single directory in
the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: select PCI_DOMAINS config from ARCH_MULTIPLATFORM
ARM: stop *MIGHT_HAVE_PCI* config from being selected redundantly
ARM: imx: (trivial) fix typo and grammar
ARM: clps711x: remove extraneous files
ARM: imx: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP2+: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP1: use IS_ENABLED() instead of checking for built-in or module
ARM: imx: remove platform-mxc_rnga
ARM: realview: imply device tree boot
ARM: realview: no need to select SMP_ON_UP explicitly
ARM: realview: delete the RealView board files
ARM: imx: no need to select SMP_ON_UP explicitly
ARM: i.MX: Move SOC_IMX1 into 'Device tree only'
ARM: i.MX: Remove i.MX1 non-DT support
ARM: i.MX: Remove i.MX1 Synertronixx SCB9328 board support
ARM: i.MX: Remove i.MX1 Armadeus APF9328 board support
ARM: mxs: remove obsolete startup code for TX28
ARM: i.MX31 iomux: remove duplicates with alternate name
ARM: i.MX31 iomux: remove plain duplicates
ARM: OMAP2+: Drop legacy board file for LDP
...
|
|
|
Thomas Gleixner
|
474aa3dd3e |
irqchip core changes for v4.9
- jcore: Add AIC driver - mips-gic: Use for_each_set_bit - mvebu: Add PIC driver -----BEGIN PGP SIGNATURE----- Version: GnuPG v2 iQIcBAABCAAGBQJX5Cv8AAoJEP45WPkGe8ZnG/YP/23xxSShaURhhgmdk7vqMlp3 D4C+YZqghx3Xq+kVTH5R20FeZbQuC7DNV1B+zo75DIbCAQ0aNCYU94DIOrGDNj/S QocuWUy4oawYl730GEE7AVQL4kBK+fOwwAn7c6HjcRunNEU/IgNXwkWZLir/hpL+ KRFWXnPSocKUh50lXcGeHPrChEduT7cz7f6U/OyYzb8AgHw3zjJiWCqMaTcIGF/V 6fYsQjEuAj79UMxsuTH0Mv0vA/SzbyhtRRBIsGcP/Ket6ZW6DfdglB3SsAdxHxRa RoweK8zVorDfixjAOA/OsZ8vrjtyF2y9e/uHVXGMWfBgbXmP19QxpxtP+7u0z1Cq /L9rW0vYoQfv3tjvSon5TUOW/QMqmqvoclSTz80nRJmocEm8Za871vD53+iFOyPE sy0CsrussaooFahIl1z/kE5bugBBJKoTAnsAtfaWpTXTW+KGWOqncxsh6H9bMZUc XXbqr5TOqJk5ck9LJafLdDeVA4Cw2j7tq4wzXPnxoPwy6Dwgdjinsw8QWMbrlywR 2zGFuFlJdbRmHftFJujZ9XorTLa7978AU5K7CHr7ofaV742DH5hBRAUvBx6jTNhA 4W9UchKtEPzgzrvESVBYSj+cgvBYllewZg1XZgxDqQQ5CI2ePTKLaQwjVWiO4Q3K d9ZytcRUtuJtEWfbnyaT =DNCg -----END PGP SIGNATURE----- Merge tag 'irqchip-core-4.9' of git://git.infradead.org/users/jcooper/linux into irq/core Pull irqchip core changes for v4.9 from Jason Cooper - jcore: Add AIC driver - mips-gic: Use for_each_set_bit - mvebu: Add PIC driver |
|
|
Alexandre TORGUE
|
e072041688 |
drivers/irqchip: Add STM32 external interrupts support
The STM32 external interrupt controller consists of edge detectors that generate interrupts requests or wake-up events. Each line can be independently configured as interrupt or wake-up source, and triggers either on rising, falling or both edges. Each line can also be masked independently. Originally-from: Maxime Coquelin <mcoquelin.stm32@gmail.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: Jason Cooper <jason@lakedaemon.net> Cc: arnd@arndb.de Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: bruherrera@gmail.com Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-gpio@vger.kernel.org Cc: Rob Herring <robh+dt@kernel.org> Cc: lee.jones@linaro.org Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1474387259-18926-3-git-send-email-alexandre.torgue@st.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> |
|
|
Jason Cooper
|
e02a9b7ce4 | Merge branch 'irqchip/mvebu64' into irqchip/core | |
|
Thomas Petazzoni
|
a109893bd3 |
irqchip/mvebu-pic: New driver for Marvell Armada 7K/8K PIC
The Marvell Armada 7K/8K integrates a secondary interrupt controller very originally named "PIC". It is connected to the main GIC via a PPI. Amongst other things, this PIC is used for the ARM PMU. This commit adds a simple irqchip driver for this interrupt controller. Since this interrupt controller is not needed early at boot time, we make the driver a proper platform driver rather than use the IRQCHIP_DECLARE() mechanism. Signed-off-by: Yehuda Yitschak <yehuday@marvell.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Link: https://lkml.kernel.org/r/1470408921-447-3-git-send-email-thomas.petazzoni@free-electrons.com Signed-off-by: Jason Cooper <jason@lakedaemon.net> |
|
|
Linus Walleij
|
8f2c00629e |
ARM: realview: imply device tree boot
This reduces the Kconfig for the RealView by assuming we are always booting from the device tree, and removing all the uses of CONFIG_REALVIEW_DT and replacing with CONFIG_ARCH_REALVIEW. Further: - Drop REALVIEW_HIGH_PHYS_OFFSET: we don't use this with device tree. - Drop the REALVIEW_EB_ARM11MP_REVB option: we now handle this by simply using another device tree. - Drop the PB1176 secure flash option: this is defined in the PB1176 device tree but marked as "disabled", so users who want to use it can simply enable it in the device tree and go hacking around. Cc: Brian Norris <computersforpeace@gmail.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Rich Felker
|
981b58f66c |
irqchip/jcore-aic: Add J-Core AIC driver
There are two versions of the J-Core interrupt controller in use, aic1 which generates interrupts with programmable priorities, but only supports 8 irq lines and maps them to cpu traps in the range 17 to 24, and aic2 which uses traps in the range 64-127 and supports up to 128 irqs, with priorities dependent on the interrupt number. The Linux driver does not make use of priorities anyway. For simplicity, there is no aic1-specific logic in the driver beyond setting the priority register, which is necessary for interrupts to work at all. Eventually aic1 will likely be phased out, but it's currently in use in deployments and all released bitstream binaries. Signed-off-by: Rich Felker <dalias@libc.org> Link: https://lkml.kernel.org/r/c3b89ef74aaa6477575dbe2d410eb1d182503243.147018b6529.git.dalias@libc.org Signed-off-by: Jason Cooper <jason@lakedaemon.net> |
|
|
Thomas Gleixner
|
4030103b9b |
irqchip core changes for v4.8 (second set)
- Add Aspeed VIC driver -----BEGIN PGP SIGNATURE----- Version: GnuPG v2 iQIcBAABCAAGBQJXdwfpAAoJEP45WPkGe8ZnhM0P/1Y4A4JU8U8kZHLHCAZgxMAT Bvjqj7liwWH/KohM7WEr0DoYG5v2gxcN0tXLENez03sqO8UnDoG44UPDPeRdUR0y lqrVvg5rCHjoEzg2ilO8lpgfY2BLvF9fYTTrj0g79URpnKijqYDlM9e1cfBw0wh8 bVsIBB9WkZFVpWiGE+aONbfDnUN59hrKz/lSdOo88g97Cgs4kl8Rn75mMTqhMpYg 7ttCu6a3dnKUSDFYcOeFHglNXg7gzTsV+FDAQ2NO7ikVDMP4YLAC9XuLuaIUBMbh 3VO41pmhJ1LGzCFQidtG0vDF/e9Sj+ifmTorh+icEspS56OwsG1XVQeqsrLEnBrX gM7jkq9+4861BJKRIM18g94YxPNlHrkw1JifMw3DlTar7sGUk5SSdHys7+wFtc4t X8dGcgiTzv4zGcCRgFbWv78zEqHnnF3LjYtXC7kOqwiSw5vugkqtLocrze5X5D9+ pnPIcuZN3rRvmZu+uO44asmA3quQc9ohE1JvyAcG2zTdNkj54HGbsGihhdEGhHJx tJoXdAssCjQxky8/uca5fb2lAz5yKfTjRx6hb7iu6wys4LDzF/lXl1JrOLbifw0n l/4w5qSxykDhuVtPJQ919HdFMDN9Zum5UDmhOu5t6/3j7fcNizdG3l0ikbyFRwW2 Mp5Z09BfjKKCYo1l2qeG =09Q0 -----END PGP SIGNATURE----- Merge tag 'irqchip-core-4.8-2' of git://git.infradead.org/users/jcooper/linux into irq/core Pull irqchip core changes for v4.8 (second set) from Jason Cooper: - Add Aspeed VIC driver |
|
|
Benjamin Herrenschmidt
|
5952884258 |
irqchip/aspeed-vic: Add irq controller for Aspeed
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lkml.kernel.org/r/1463064193-2178-3-git-send-email-joel@jms.id.au Signed-off-by: Jason Cooper <jason@lakedaemon.net> |
|
|
Jon Hunter
|
9c8edddfc9 |
irqchip/gic: Add platform driver for non-root GICs that require RPM
Add a platform driver to support non-root GICs that require runtime power-management. Currently, only non-root GICs are supported because the functions, smp_cross_call() and set_handle_irq(), that need to be called for a root controller are located in the __init section and so cannot be called by the platform driver. The GIC platform driver re-uses many functions from the existing GIC driver including some functions to save and restore the GIC context during power transitions. The functions for saving and restoring the GIC context are currently only defined if CONFIG_CPU_PM is enabled and to ensure that these functions are always defined when the platform driver is enabled, a dependency on CONFIG_ARM_GIC_PM (which selects the platform driver) has been added. In order to re-use the private GIC initialisation code, a new public function, gic_of_init_child(), has been added which calls various private functions to initialise the GIC. This is different from the existing gic_of_init() because it only supports non-root GICs (ie. does not call smp_cross_call() is set_handle_irq()) and is not located in the __init section (so can be used by platform drivers). Furthermore, gic_of_init_child() dynamically allocates memory for the GIC chip data which is also different from gic_of_init(). There is no specific suspend handling for GICs registered as platform devices. Non-wakeup interrupts will be disabled by the kernel during late suspend, however, this alone will not power down the GIC if interrupts have been requested and not freed. Therefore, requestors of non-wakeup interrupts will need to free them on entering suspend in order to power-down the GIC. Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> |
|
|
Linus Torvalds
|
0efacbbaee |
ARC updates for 4.7-rc1
- Support for EZChip (now Mellanox) NPS-400 Network processor based on ARC700
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy domains)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pnAx
-----END PGP SIGNATURE-----
Merge tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"We have a relatively big changeset for ARC for 4.7.
The highlight is support for EZChip (now Mellanox) NPS-400 network
processor, a 400-Gb throughput C-programmable packet processor based
on ARC700 cores from Synopsys. See
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
Also present are irqchip and clocksource drivers for NPS as agreed
with respective maintainers to go via ARC tree due to an soc header
dependency. I have the needed ACKs from Jason, Marc, Daniel. You
might run into a trivial merge conflict in drivers/irqchip/*
This EZChip platform support required some deep changes in ARC
architecture code and also opportunity to cleanup past sins (legacy
irq domains, missing irq domain lookup, hard coded timer irqs...)
Summary:
- Support for EZChip (now Mellanox) NPS-400 Network processor based
on ARC700
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy
domains)"
* tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (37 commits)
arc: axs103_smp: Fix CPU frequency to 100MHz for dual-core
arc: axs10x: Add DT bindings for I2S PLL Clock
ARC: pae: STRICT_MM_TYPECHECKS was broken
ARC: Add eznps platform to Kconfig and Makefile
ARC: [plat-eznps] Use dedicated COMMAND_LINE_SIZE
ARC: [plat-eznps] Use dedicated cpu_relax()
ARC: [plat-eznps] Use dedicated identity auxiliary register.
ARC: [plat-eznps] Use dedicated SMP barriers
ARC: [plat-eznps] Use dedicated atomic/bitops/cmpxchg
ARC: [plat-eznps] Use dedicated user stack top
ARC: [plat-eznps] Add eznps platform
ARC: [plat-eznps] Add eznps board defconfig and dts
ARC: Mark secondary cpu online only after all HW setup is done
ARC: rwlock: disable interrupts in !LLSC variant
ARC: Make vmalloc size configurable
ARC: clean out UAPI byteorder.h clean off Kconfig symbol
irqchip: add nps Internal and external irqchips
clocksource: Add NPS400 timers driver
soc: Support for EZchip SoC
Documentation: Add EZchip vendor to binding list
...
|
|
|
Vladimir Zapolskiy
|
8cb17b5ed0 |
irqchip: Add LPC32xx interrupt controller driver
The change adds improved support of NXP LPC32xx MIC, SIC1 and SIC2 interrupt controllers. This is a list of new features in comparison to the legacy driver: * irq types are taken from device tree settings, no more need to hardcode them, * old driver is based on irq_domain_add_legacy, which causes problems with handling MIC hardware interrupt 0 produced by SIC1, * there is one driver for MIC, SIC1 and SIC2, no more need to handle them separately, e.g. have two separate handlers for SIC1 and SIC2, * the driver does not have any dependencies on hardcoded register offsets, * the driver is much simpler for maintenance, * SPARSE_IRQS option is supported. Legacy LPC32xx interrupt controller driver was broken since commit |
|
|
Noam Camus
|
44df427c89 |
irqchip: add nps Internal and external irqchips
Adding EZchip NPS400 support. Internal interrupts are handled by Multi Thread Manager (MTM) Once interrupt is serviced MTM is acked for deactivating the interrupt. External interrupts are handled by MTM as well as at Global Interrupt Controller (GIC) e.g. serial and network devices. Signed-off-by: Noam Camus <noamc@ezchip.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Vineet Gupta <vgupta@synopsys.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Cc: Thomas Gleixner <tglx@linutronix.de> |