Jana Iyengar found an interesting issue on CUBIC :
The epoch is only updated/reset initially and when experiencing losses.
The delta "t" of now - epoch_start can be arbitrary large after app idle
as well as the bic_target. Consequentially the slope (inverse of
ca->cnt) would be really large, and eventually ca->cnt would be
lower-bounded in the end to 2 to have delayed-ACK slow-start behavior.
This particularly shows up when slow_start_after_idle is disabled
as a dangerous cwnd inflation (1.5 x RTT) after few seconds of idle
time.
Jana initial fix was to reset epoch_start if app limited,
but Neal pointed out it would ask the CUBIC algorithm to recalculate the
curve so that we again start growing steeply upward from where cwnd is
now (as CUBIC does just after a loss). Ideally we'd want the cwnd growth
curve to be the same shape, just shifted later in time by the amount of
the idle period.
Reported-by: Jana Iyengar <jri@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Sangtae Ha <sangtae.ha@gmail.com>
Cc: Lawrence Brakmo <lawrence@brakmo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing a CC TX_START event on control frames like pure ACK
is a waste of time, as a CC should not care.
Following patch needs this change, as we want CUBIC to properly track
idle time at a low cost, with a single TX_START being generated.
Yuchung might slightly refine the condition triggering TX_START
on a followup patch.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Cc: Jana Iyengar <jri@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Sangtae Ha <sangtae.ha@gmail.com>
Cc: Lawrence Brakmo <lawrence@brakmo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally that parameter was always reset to num_online_cpus during
module initialisation, which renders it useless.
The fix is to only set max_queues to num_online_cpus when user has not
provided a value.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally that parameter was always reset to num_online_cpus during
module initialisation, which renders it useless.
The fix is to only set max_queues to num_online_cpus when user has not
provided a value.
Reported-by: Johnny Strom <johnny.strom@linuxsolutions.fi>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=104031
Fixes: 6e85d5ad36
Based on the discussion starting at
http://www.spinics.net/lists/netdev/msg342193.html
Tested locally on RTL8168evl/8111evl with various concurrent processes
accessing /proc/net/dev while changing the link state as well as
removing/reloading the r8169 module.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: poma <pomidorabelisima@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like single link MIPI panels, similarly for dual link panels, pipe
to be configured is based on the DVO port from VBT Block 2. In hardware,
Port A is mapped with Pipe A and Port C is mapped with Pipe B.
This issue got introduced in -
commit 7e9804fdcf
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Jan 16 14:27:23 2015 +0200
drm/i915/dsi: add drm mipi dsi host support
Cc: stable@vger.kernel.org # v4.0
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If one disables DDR DVFS in the BIOS, Punit will apparently ignores
all DDR DVFS request. Currently we assume that DDR DVFS is always
operational, which leads to errors in dmesg when the DDR DVFS requests
time out.
Fix the problem by gently prodding Punit during driver load to find out
whether it will respond to DDR DVFS requests. If the request times out,
we assume that DDR DVFS has been permanenly disabled in the BIOS and
no longer perster the Punit about it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91629
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix a wrong logical AND (&&) used for the range check of CSR MMIO.
Spotted nicely by gcc -Wlogical-op flag:
drivers/gpu/drm/i915/intel_csr.c: In function ‘finish_csr_load’:
drivers/gpu/drm/i915/intel_csr.c:353:41: warning: logical ‘and’ of mutually exclusive tests is always false [-Wlogical-op]
Fixes: eb805623d8 ('drm/i915/skl: Add support to load SKL CSR firmware.')
Cc: <stable@vger.kernel.org> # v4.2
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
IEEE 1722 describes AVB (later renamed to TSN - Time Sensitive
Networking), a protocol, encapsualtion and synchronization to utilize
standard networks for audio/video (and later other time-sensitive)
streams.
This standard uses ethertype 0x22F0.
http://standards.ieee.org/develop/regauth/ethertype/eth.txt
This is a respin of a previous patch ("ether: add AVB frame type
ETH_P_AVB")
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: linux-api@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Henrik Austad <henrik@austad.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The linux/audit.h header uses EM_MICROBLAZE in order to define
AUDIT_ARCH_MICROBLAZE, but it's only available in the microblaze
asm headers. Move it to the common elf-em.h header so that the
define can be used on non-microblaze systems. Otherwise we get
build errors that EM_MICROBLAZE isn't defined when we try to use
the AUDIT_ARCH_MICROBLAZE symbol.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When netlink mmap on receive side is the consumer of nf queue data,
it can happen that in some edge cases, we write skb shared info into
the user space mmap buffer:
Assume a possible rx ring frame size of only 4096, and the network skb,
which is being zero-copied into the netlink skb, contains page frags
with an overall skb->len larger than the linear part of the netlink
skb.
skb_zerocopy(), which is generic and thus not aware of the fact that
shared info cannot be accessed for such skbs then tries to write and
fill frags, thus leaking kernel data/pointers and in some corner cases
possibly writing out of bounds of the mmap area (when filling the
last slot in the ring buffer this way).
I.e. the ring buffer slot is then of status NL_MMAP_STATUS_VALID, has
an advertised length larger than 4096, where the linear part is visible
at the slot beginning, and the leaked sizeof(struct skb_shared_info)
has been written to the beginning of the next slot (also corrupting
the struct nl_mmap_hdr slot header incl. status etc), since skb->end
points to skb->data + ring->frame_size - NL_MMAP_HDRLEN.
The fix adds and lets __netlink_alloc_skb() take the actual needed
linear room for the network skb + meta data into account. It's completely
irrelevant for non-mmaped netlink sockets, but in case mmap sockets
are used, it can be decided whether the available skb_tailroom() is
really large enough for the buffer, or whether it needs to internally
fallback to a normal alloc_skb().
>From nf queue side, the information whether the destination port is
an mmap RX ring is not really available without extra port-to-socket
lookup, thus it can only be determined in lower layers i.e. when
__netlink_alloc_skb() is called that checks internally for this. I
chose to add the extra ldiff parameter as mmap will then still work:
We have data_len and hlen in nfqnl_build_packet_message(), data_len
is the full length (capped at queue->copy_range) for skb_zerocopy()
and hlen some possible part of data_len that needs to be copied; the
rem_len variable indicates the needed remaining linear mmap space.
The only other workaround in nf queue internally would be after
allocation time by f.e. cap'ing the data_len to the skb_tailroom()
iff we deal with an mmap skb, but that would 1) expose the fact that
we use a mmap skb to upper layers, and 2) trim the skb where we
otherwise could just have moved the full skb into the normal receive
queue.
After the patch, in my test case the ring slot doesn't fit and therefore
shows NL_MMAP_STATUS_COPY, where a full skb carries all the data and
thus needs to be picked up via recv().
Fixes: 3ab1f683bf ("nfnetlink: add support for memory mapped netlink")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of netlink mmap, there can be situations where received frames
have to be placed into the normal receive queue. The ring buffer indicates
this through NL_MMAP_STATUS_COPY, so the user is asked to pick them up
via recvmsg(2) syscall, and to put the slot back to NL_MMAP_STATUS_UNUSED.
Commit 0ef707700f ("netlink: rx mmap: fix POLLIN condition") changed
polling, so that we walk in the worst case the whole ring through the
new netlink_has_valid_frame(), for example, when the ring would have no
NL_MMAP_STATUS_VALID, but at least one NL_MMAP_STATUS_COPY frame.
Since we do a datagram_poll() already earlier to pick up a mask that could
possibly contain POLLIN | POLLRDNORM already (due to NL_MMAP_STATUS_COPY),
we can skip checking the rx ring entirely.
In case the kernel is compiled with !CONFIG_NETLINK_MMAP, then all this is
irrelevant anyway as netlink_poll() is just defined as datagram_poll().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorporate fw_ldst_cmd structure change for new firmware and also
update version string for the same
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist one issue by below case that case system hang:
ifconfig eth0 down
ifconfig eth0 hw ether 00:10:19:19:81:19
After eth0 down, all fec clocks are gated off. In the .fec_set_mac_address()
function, it will set new MAC address to registers, which causes system hang.
So it needs to add netif status check to avoid registers access when clocks are
gated off. Until eth0 up the new MAC address are wrote into related registers.
V2:
As Lucas Stach's suggestion, add a comment in the code to explain why it needed.
CC: Lucas Stach <l.stach@pengutronix.de>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: fix the autoresume may fail
Fix the autosuspend issues which occur about linking change.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the runtime suspend issues result from the linking change.
Case 1:
a) link down occurs.
b) driver disable tx/rx.
c) autosuspend occurs.
d) hw linking up.
e) device suspends without enabling tx/rx.
f) couldn't wake up when receiving packets.
Case 2:
a) Nway results in linking down.
b) autosuspend occurs.
c) device suspends.
d) device may not wake up when linking up.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split DRIVER_VERSION into NETNEXT_VERSION and NET_VERSION. Then,
according to the value of DRIVER_VERSION, we could know which
patches are used generally without comparing the source code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/route.c:2946:3-8: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
Generated by: scripts/coccinelle/free/ifnullfree.cocci
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Microchip LAN88XX phy driver for phylib.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current check of phydev with IS_ERR(phydev) may make not much sense
because of_phy_connect() returns NULL on failure instead of error value.
Still for checking result of phy_connect() IS_ERR() makes perfect sense.
So let's use combined check IS_ERR_OR_NULL() that covers both cases.
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all cases, mbx->req.arg and mbx->rsp.arg have just been allocated
using kcalloc(), so these six memsets are redundant.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The double memset is a little ugly; using kzalloc avoids it altogether.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using kzalloc saves a tiny bit on .text.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We save a little .text and get rid of the sizeof(...) style
inconsistency.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
PBIAS regulator is required for MMC module in OMAP2, OMAP3, OMAP4,
OMAP5 and DRA7 SoCs. Enable it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This switches IPv6 policy routing to use the shared
fib_default_rule_pref() function of IPv4 and DECnet. It is also used in
multicast routing for IPv4 as well as IPv6.
The motivation for this patch is a complaint about iproute2 behaving
inconsistent between IPv4 and IPv6 when adding policy rules: Formerly,
IPv6 rules were assigned a fixed priority of 0x3FFF whereas for IPv4 the
assigned priority value was decreased with each rule added.
Since then all users of the default_pref field have been converted to
assign the generic function fib_default_rule_pref(), fib_nl_newrule()
may just use it directly instead. Therefore get rid of the function
pointer altogether and make fib_default_rule_pref() static, as it's not
used outside fib_rules.c anymore.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
For !CONFIG_OF of_get_property() is defined to always return NULL. Thus
there's no need to protect the call to of_get_property() with #ifdef
CONFIG_OF.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro to write 64-bits quantities to the 32-bits register swapped
the value and offsets arguments, we want to preserve the ordering of the
arguments with respect to how writel() is implemented for instance:
value first, offset/base second.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when the verifier log is enabled the print_bpf_insn() is doing
bpf_alu_string[BPF_OP(insn->code) >> 4]
and
bpf_jmp_string[BPF_OP(insn->code) >> 4]
where BPF_OP is a 4-bit instruction opcode.
Malformed insns can cause out of bounds access.
Fix it by sizing arrays appropriately.
The bug was found by clang address sanitizer with libfuzzer.
Reported-by: Yonghong Song <yhs@plumgrid.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem:
The ecmp route replace support for ipv6 in the kernel, deletes the
existing ecmp route too early, ie when it installs the first nexthop.
If there is an error in installing the subsequent nexthops, its too late
to recover the already deleted existing route leaving the fib
in an inconsistent state.
This patch reduces the possibility of this by doing the following:
a) Changes the existing multipath route add code to a two stage process:
build rt6_infos + insert them
ip6_route_add rt6_info creation code is moved into
ip6_route_info_create.
b) This ensures that most errors are caught during building rt6_infos
and we fail early
c) Separates multipath add and del code. Because add needs the special
two stage mode in a) and delete essentially does not care.
d) In any event if the code fails during inserting a route again, a
warning is printed (This should be unlikely)
Before the patch:
$ip -6 route show
3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024
/* Try replacing the route with a duplicate nexthop */
$ip -6 route change 3000:1000:1000:1000::2/128 nexthop via
fe80::202:ff:fe00:b dev swp49s0 nexthop via fe80::202:ff:fe00:d dev
swp49s1 nexthop via fe80::202:ff:fe00:d dev swp49s1
RTNETLINK answers: File exists
$ip -6 route show
/* previously added ecmp route 3000:1000:1000:1000::2 dissappears from
* kernel */
After the patch:
$ip -6 route show
3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024
/* Try replacing the route with a duplicate nexthop */
$ip -6 route change 3000:1000:1000:1000::2/128 nexthop via
fe80::202:ff:fe00:b dev swp49s0 nexthop via fe80::202:ff:fe00:d dev
swp49s1 nexthop via fe80::202:ff:fe00:d dev swp49s1
RTNETLINK answers: File exists
$ip -6 route show
3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fBLOCKREADINTR is masking the notification from the remote and should
hence be cleared while we're waiting the tx fifo to drain. Also change
the reset state to mask the notification, as send is the only use case
where we're interested in it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch fixes SMEM addressing issues when remote processors need to use
secure SMEM partitions.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
This patch corrects private partition item access. Instead of falling back to
global for instances where we have an actual host and remote partition existing,
return the results of the private lookup.
Signed-off-by: Andy Gross <agross@codeaurora.org>
PCT_TO_HWP does not take the actual range of pstates exported
by HWP_CAPABILITIES in account, and is broken on most platforms.
Remove the macro and set the min and max pstate for hwp by
determining the range and adjusting by the min and max percent
limits values.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In current code, max_perf_pct might be smaller than min_perf_pct
by improper user input:
$ grep . /sys/devices/system/cpu/intel_pstate/m*_perf_pct
/sys/devices/system/cpu/intel_pstate/max_perf_pct:100
/sys/devices/system/cpu/intel_pstate/min_perf_pct:100
$ echo 80 > /sys/devices/system/cpu/intel_pstate/max_perf_pct
$ grep . /sys/devices/system/cpu/intel_pstate/m*_perf_pct
/sys/devices/system/cpu/intel_pstate/max_perf_pct:80
/sys/devices/system/cpu/intel_pstate/min_perf_pct:100
Fix this problem by 2 steps:
1. Normalize the user input to [min_policy, max_policy].
2. Make sure max_perf_pct>=min_perf_pct, suggested by Seiichi Ikarashi.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no point returning suspend_opp, if it is disabled by the core.
As we can't use it at all. Fix it.
Fixes: 4eafbd15b6 ("PM / OPP: add dev_pm_opp_get_suspend_opp() helper")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use stdout-path so that we don't have to put the console on the
kernel command line.
Cc: Tim Bird <tim.bird@sonymobile.com>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use stdout-path so that we don't have to put the console on the
kernel command line.
Cc: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Eric Dumazet