rt2x00usb_vendor_request_large_buff is write-only, so it is
safe to make the argument a const.
Fixes compile warning:
drivers/net/wireless/rt2x00/rt73usb.c: In function 'rt73usb_load_firmware':
drivers/net/wireless/rt2x00/rt73usb.c:916: warning: passing argument 5 of 'rt2x00usb_vendor_request_large_buff' discards qualifiers from pointer target typ
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some module parameters with only one line have the '\n' at the end of the
description. This is not needed nor wanted as after the description the
type (i.e. int) is followed by a newline.
Some modules contain a multi-line description, these are not affected
by this patch.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Ed L. Cashin <ecashin@coraid.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Roland Dreier <rolandd@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
iwl3945_rx_reply_rx was sending packets too early to
mac80211, before updating signal strength/quality.
This resulted in garbage power levels.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the standard offsetof() macro to fix a compile warning below:
CC [M] drivers/net/wireless/prism54/isl_ioctl.o
drivers/net/wireless/prism54/isl_ioctl.c: In function 'prism2_ioctl_set_generic_element':
drivers/net/wireless/prism54/isl_ioctl.c:2658: warning: cast from pointer to integer of different size
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw_write8() can't be used alone with a loop because of a wrong definition.
CC [M] drivers/net/wireless/ipw2200.o
drivers/net/wireless/ipw2200.c: In function 'ipw_ethtool_set_eeprom':
drivers/net/wireless/ipw2200.c:10579: warning: array subscript is above array bounds
drivers/net/wireless/ipw2200.c: In function 'ipw_load':
drivers/net/wireless/ipw2200.c:2663: warning: array subscript is above array bounds
Add missing do {} while (0) to fix them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some users of the RTL8187B have experienced difficulties since commit
49292d5635 that introduced the power
management wext hooks. This difficulty has not made much sense until
it was realized that it was possible for mac80211 to make a call to the
config routine while that routine was already being executed. On this
device, it is necessary to loopback the TX when changing channels. Unless
this is properly restored, the device will lockup. A mutex now protects
the device state, and the private data in several places.
The problem was found by Herton Ronaldo Krzesinski <herton@mandriva.com.br>,
who also suggested this type of fix.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In kernel version 2.6.26-rc9 my wireless LAN card worked; but in the
released 2.6.26, my RaLink rt2500 card wouldn't associate.
Git-bisect led me to this patch:
61486e0f68
rt2x00: Remove ieee80211_tx_control argument from write_tx_desc()
I believe that there is a problem with that patch --- it
(inadvertantly) removes an extra line of code, that used to set the
DATABYTE_COUNT field.
This patch reinstates that line, and with it my card works again.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since only mesh-enabled firmware has the CMD_802_11_MONITOR_MODE on
which the rtap functionality depends, only expose the rtap functionality
when mesh is also available.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sequence counter can be accessed in IRQ context,
which means the lock protecting the counter should
be irqsave. To prevent making the entire intf->lock irqsave
without reason, create a new lock which only protects
the sequence counter.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM_BBPTUNE_VGC word is valid, we should
override EEPROM_BBPTUNE_VGCLOWER field with the BBP
value.
And we should _not_ do that when EEPROM_BBPTUNE_R17 is valid.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the hardware has indicated the firmware upload has completed
and the device is ready, we should wait another millisecond to
make sure the device is really ready to continue.
Without this timout, bringing the interface down and up again will
fail due to incorrect register initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The if-statement to determine the new TX/RX antenna
configuration was incomplete. It lacks the general
else-clause when the antenna wasn't changed.
This is a correct event, since it can occur when only
one of the antenna's has been changed or when the new
configuration is being forced (like when the interface
has just been added).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although most rt2x00 debugfs files don't contain
information which could compromise network security,
it is better to set the access permissions to root only.
This will be required when HW crypto is implemented,
because it could be possible to read the HW key from
the registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids stopping queue in the middle of the fragmented packet.
It is required that there will be ~10 (max packet/min fragment) or 16
(4 bits of frag number) free tfds all the time.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mask out previously demanded interrupt flags because we set
new ones. Don't allow mixing them after switch from sta to
ibss and vice versa.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Enable I/Q calibration each time we have correction results (we
were only enabling calibration during reset). If we don't we commit
the same results each time calibration routine is called.
* Add some documentation and a TODO on nf calibration
* Return -EAGAIN on noise floor timeout/failure
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add channel function for RF2425 (got this from decompiling binary
HAL, i have no idea why there is a 5GHz section but i'm looking
into it)
* Update RF5112 channel function (also got this from decompiling binary HAL)
* Set JAPAN setting for channel 14 on all PHY chips
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add initial RF gain settings for RF2425
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update ath5k_hw_reset and add some more documentation about PHY calibration
* Fix ath5k_hw_set_power to use AR5K_SLEEP_CTL_SLE_ALLOW for Network sleep
* Preserve sleep duration field while setting AR5K_SLEEP_CTL
and reduce delays & checks for register's status (got this from
decompiling & dumps, it works for me but it needs testing)
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Do an ADC test during reset to match recent regdumps
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update hw_reset to calculate some of the values we were using as static
* Increase activation to rx delay
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Correctly attach RF2425
* Update SREV values for Radio chips
* Update hw_attach to use new SPENDING values
* Write a bit after POST for some chips
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Restore saved initial value after POST
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update list of registers
* Use updated register macros inside hw.c, initvals.c and debug.c
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When support for multiple TX queues were added, the
netif_tx_lock() routines we converted to iterate over
all TX queues and grab each queue's spinlock.
This causes heartburn for lockdep and it's not a healthy
thing to do with lots of TX queues anyways.
So modify this to use a top-level lock and a "frozen"
state for the individual TX queues.
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary to set the dongle type on the nsc driver in order to get
it to work correctly. Thinkpads all appear to use dongle type 9. This
patch defaults nsc devices with an IBM PnP descriptor to use type 9.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Adapt the tg3 driver to use the reworked PCI PM and make it use the
exported PCI PM core functions instead of accessing the PCI PM registers
directly by itself.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SH7763 has Ethernet core same as SH7710/SH7712.
Positions of some registry are different, but the basic part is the same.
I add support of ethernet of sh7763 to sh_eth.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Trying to build with CONFIG_NE2000=m fails with:
scripts/mod/modpost -o /tmp/tmp/linux-2.6.27-rc1/Module.symvers -S -s
ERROR: "NS8390_init" [drivers/net/ne.ko] undefined!
This is because the split of 8390 into pausing and non-pausing
versions was incompletely propagated to ne.c. This fixes it.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dm_{read,write}() were doing USB transfers of data on stack, which isn't
allowed. Fix it by kmalloc'ing a temporary buffer.
Clean up the error handling for short transfers while we're at it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The callers of niu_ethflow_to_class expect zero as error, but it returns
-1 instead.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On s2io driver, when you change the interface MTU, it invokes a card
reset, which flush some statistics. This patch solves this problem, and
also set the net_device->stats as the default statistics structure,
instead of s2io_nic->stats.
To do that, s2io_nic->stats turned into a staging area, where is saved
statistics of the last hardware statistics query. So, the difference
between the current hardware statistics and s2io_nic->stats, is the
value that should be summed up, in order to get the correct statistics
value, even after a reset.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Recent changes to the IRQ framework have made passing the wrong
trigger type to request_irq() become a fatal error. In the case
of the enc28j60 driver, it stopped working in my test harness.
(Specifically: the signal detects "pin change" events, both edges,
not just falling edges. Similarly, other boards might route it
through an inverter. Trigger type are board-specific.)
This fixes that problem by the usual fix of expecting board setup
code to have set up the correct IRQ trigger type. The best known
example of that being x86 setup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Starting with FW version 7.0, the driver needs to allow larger images.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reprogram MAC address after resume from Suspend Mem
(Blackfin Hibernate looses all CORE and SYSTEM register content)
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for the realtek 8211c phy. The driver must
perform a hardware reset of the phy due to an errata where the phy could
not detect the link.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ivo van Doorn