I broke this with my commit
07cfe0e7a8
This fixes fdo #33434
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It is illegal to call netif_stop_queue before register_netdev.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running insmod/rmood in a loop, an unnecessary netif_stop_queue
causes the system to crash. Remove the netif_stop_queue call
and netif_start_queue in the link status update path.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments under "config STUB_POULSBO" are close to correct,
but they are not being followed. This patch updates them to reflect
the requirements for THERMAL.
This build error is caused by STUB_POULSBO selecting ACPI_VIDEO
when ACPI_VIDEO's config requirements are not met.
ERROR: "thermal_cooling_device_register" [drivers/acpi/video.ko] undefined!
ERROR: "thermal_cooling_device_unregister" [drivers/acpi/video.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This warning was reported by cppcheck:
drivers/isdn/icn/icn.c:1641: error: Dangerous usage of 'rev' (strncpy doesn't always 0-terminate it)
If strncpy copied 20 bytes, the destination string rev was not terminated.
The patch adds one more byte to rev and makes sure that this byte is
always 0.
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip was erroneously configured to accept all multicast frames
in a normal (none-promisc) rx mode both on the RSS and on the FCoE L2 rings
when in an NPAR mode. This caused packet duplication for every received multicast
frame in this mode.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Early chipsets (gen2/3) used function 1 as a placeholder for multi-head.
We used to ignore these since they were not assigned to
PCI_CLASS_DISPLAY_VGA. However with 934f992c7 we attempt to bind to all
Intel PCI_CLASS_DISPLAY devices (and functions) to work in multi-gpu
systems. This fails hard on gen2/3.
Reported-by: Ferenc Wágner <wferi@niif.hu>
Tested-by: Ferenc Wágner <wferi@niif.hu>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28012
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This error is reported by cppcheck:
drivers/net/vxge/vxge-config.c:3693: warning: Mutual exclusion over || always evaluates to true. Did you intend to use && instead?
It looks like cppcheck is correct, so fix this. No test was run.
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Sivakumar Subramani <sivakumar.subramani@exar.com>
Cc: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Cc: Jon Mason <jon.mason@exar.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When built with rcu checks enabled, vhost triggers
bogus warnings as vhost features are read without
dev->mutex sometimes, and private pointer is read
with our kind of rcu where work serves as a
read side critical section.
Fixing it properly is not trivial.
Disable the warnings by stubbing out the checks for now.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This error was reported by cppcheck:
drivers/net/enc28j60.c:815: error: Using sizeof for array given as function argument returns the size of pointer.
The original code reads 4 or 8 bytes instead of TSV_SIZE (= 100) bytes.
I just fixed the code, but did not run any tests.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
axnet_cs:
mdelay of 10ms is too long at ei_rx_overrun.
It should be reduced to 2ms.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (42 commits)
usb: gadget: composite: avoid access beyond array max length
USB: serial: handle Data Carrier Detect changes
USB: gadget: Fix endpoint representation in ci13xxx_udc
USB: gadget: Fix error path in ci13xxx_udc gadget probe function
usb: pch_udc: Fix the worning log issue at gadget driver remove
USB: serial: Updated support for ICOM devices
USB: ehci-mxc: add work-around for efika mx/sb bug
USB: unbreak ehci-mxc on otg port of i.MX27
drivers: update to pl2303 usb-serial to support Motorola cables
USB: adding USB support for Cinterion's HC2x, EU3 and PH8 products
USB serial: add missing .usb_driver field in serial drivers
USB: ehci-fsl: Fix 'have_sysif_regs' detection
USB: g_printer: fix bug in module parameter definitions
USB: g_printer: fix bug in unregistration
USB: uss720: remove duplicate USB device
MAINTAINERS: add ueagle-atm entry
USB: EHCI: fix DMA deallocation bug
USB: pch_udc: support new device ML7213 IOH
usb: pch_udc: Fixed issue which does not work with g_serial
usb: set ep_dev async suspend should be later than device_initialize
...
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (26 commits)
staging: r8712u: Add new device IDs
staging: brcm80211: fix suspend/resume issue in brcmsmac
staging: brcm80211: remove assert to avoid panic since 2.6.37 kernel
Staging: iio: Aditional fixpoint formatted output bugfix
staging: usbip: vhci: use urb->dev->portnum to find port
staging: usbip: vhci: handle EAGAIN from SO_RCVTIMEO
staging: usbip: vhci: friendly log messages for connection errors
staging: usbip: vhci: refuse to enqueue for dead connections
staging: usbip: vhci: give back URBs from in-flight unlink requests
staging: usbip: vhci: update reference count for usb_device
staging: usbip: stub: update refcounts for devices and interfaces
staging: tidspbridge: replace mbox callback with notifier_call
staging: comedi: ni_labpc: Use shared IRQ for PCMCIA card
Staging: speakup: &&/|| confusion in silent_store()
iio: Fixpoint formatted output bugfix
staging: rt2860: Fix incorrect netif_stop_queue usage warning
staging: r8712u: Fix memory leak in firmware loading
staging: tidspbridge: configure full L1 MMU range
staging: rt2870sta: Add ID for Linksys WUSB100v2
Staging: xgfib: put parenthesis in the right place
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/serial: fix apbuart build
n_hdlc: fix read and write locking
serial: unbreak billionton CF card
tty: use for_each_console() and WARN() on sysfs failures
vt: fix issue when fbcon wants to takeover a second time.
Fix up trivial conflict in drivers/tty/tty_io.c
Without this dependency the softing driver will be buildable on s390,
where it fails.
Signed-Off-By: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DEBUG_SPI is included in the debug log level wl1271_spi_reset()
will dump the already freed memory instead of the SPI buffer.
This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One saa7111 device is reporting a different ID:
saa7115 0-0024: chip found @ 0x48 (ID 0f7111d0e111111) does not match a known saa711x chip.
As this is for sure a saa7111, change the detection code to also
cover this device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The streamzap driver has relatively low sampling resolution, and any
delays in reporting events seem to cause some minor problems for the
likes of irw when using the lirc bridge driver, resulting in a single
keypress registering as multiple independent ones, rather than as a
single press with repeats. If we call ir_raw_event_handle() more
frequently and reset the rawir kfifo at end-of-signal, the behavior
improves quite a bit.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure rawir struct is zeroed out before populating it for each
ir_raw_event_store_with_filter() call, and when we see a trailing 0x80
packet (end-of-data), issue an ir_raw_event_reset() call.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to my own stupidity, some of the wrong time unit conversion macros
were being used inside some of the IR drivers I've been working on. Fix
that, and convert over some additional places to also use the macros.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some occasionally useful debug spew disappeared as part of a feature
update a while back, and I'm finding myself in need of it again to help
diagnose some issues.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the same "are you ready?" i2c_master_send() poll command to
get_key_haup_xvr found in lirc_zilog, which is apparently seen in
the Windows driver for the PVR-150 w/a z8. This stabilizes what is
received from both the HD-PVR and HVR-1950, even with their polling
intervals at the default of 100, thus the removal of the custom
260ms polling_interval in pvrusb2-i2c-core.c.
Acked-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Mike Isely <isely@isely.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both the HD-PVR and HVR-1950, driven by the hdpvr and pvrusb2 drivers
respectively, have a zilog z8 chip exposed via i2c. These are both
usb-connected devices, and on both of them, back-to-back i2c_master_send
calls that work fine with a z8 on a pci card fail with a -EIO, as the
chip isn't yet ready from the prior command. To cope with that, add a
delay and retry loop where necessary.
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have to actually call i2c_new_device() once for each of the rx and tx
addresses. Also improve error-handling and device remove i2c cleanup.
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per http://mediacenterguides.com/book/export/html/31 and investigation
by Erin, we were missing these last three mappings to complete the mce
key table. Lets remedy that.
Reported-by: Erin Simonds <fisslefink@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some cases, some frames may not end with the JPEG end of frame.
Being not complete, they are now discarded.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The problem was introduced by the commit 2af0b4c60c.
Some registers were no more initialized.
Tested-by: <Giovanni Scafora giovanni@archlinux.org>
Tested-by: <Sergey Manucharian sm@ingeniware.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hugh Dickins found that characters in xterm were going missing and oft
delayed. Being the curious type, he managed to associate this with the
new high-precision vblank patches; disabling these he found, restored
the orderliness of his characters.
The oddness begins when one realised that Hugh was not using vblanks at
all on his system (fvwm and some xterms). Instead, all he had to go on
were warning of a pipe underrun, curiously enough at around 60Hz. He
poked and found that in addition to the underrun warning, the hardware
was flagging the start of a new frame, a vblank, which in turn was
kicking off the pending vblank processing code.
There is little we can do for the underruns on Hugh's machine, a
Crestline [965GM], which must have its FIFO watermarks set to 8.
However, we do not need to process the vblank if we know that they are
disabled...
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By setting the FB of a CRTC to NULL, we are turning off the CRTC (and so
disable the unused encoders and connectors). As such we can simplify the
later tests by making sure the set->mode is NULL. Setting the
num_connectors to zero means that we do not need to loop over the unused
connectors.
All current usage appears correct, this only builds additional defense
into the routine.
References: https://bugzilla.kernel.org/show_bug.cgi?id=27722
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In drm_crtc_helper_set_config, we call drm_crtc_helper_set_mode which
may return early and do no operation if the crtc is to be disabled. In
this case we merrily swap to the new fb, discarding the old_fb believing
that it has been cleaned up. However, due to the early return, the
old_fb was not presented to the backend for correct reaping, and nor was
the new one - which is about to be reaped via the
drm_helper_disable_unused_functions(), leading to incorrect refcounting
of the pinned objects.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=27722
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29230
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We should not report incomplete blocks on error. Return the number of
bytes successfully transferred, rounded down to the nearest block.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we encounter an error, make sure we complete the transaction
otherwise we'll leave the request dangling.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prevent the following compiler warning if compiling a 31 bit kernel:
drivers/s390/cio/qdio_main.c: In function ‘get_outbound_buffer_frontier’:
drivers/s390/cio/qdio_main.c:646:16: warning: ‘state’ may be used uninitialized in this function
CC lib/radix-tree.o
CC drivers/s390/scsi/zfcp_cfdc.o
drivers/s390/cio/qdio_main.c: In function ‘qdio_inbound_q_moved’:
drivers/s390/cio/qdio_main.c:479:16: warning: ‘state’ may be used uninitialized in this function
drivers/s390/cio/qdio_main.c:479:16: note: ‘state’ was declared here
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a device is not resumed correctly the system crashes when this
device is set offline. This may happen if it gets disconnected
during suspend.
Check if the device is already removed from alias handling and skip
these steps to prevent the kernel panic.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Update bnx2x version to 1.62.00-5
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All functions on a port should be set to take the MDC/MDIO lock to avoid contention on the bus
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix link on BCM57712 + BCM8073 when port swap is enabled. Common PHY reset was done on the wrong port.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix blink rate of activity LED of the BCM84823 on 10G link
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rare link issue with the BCM8073 PHY may occur due to setting XAUI low power mode, while the PHY microcode already does that.
The fix is not to set set XAUI low power mode for this PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not respond with -EINVAL to EVIOCGKEYCODE for not-yet-mapped
scancodes, but rather return KEY_RESERVED.
This fixes breakage with Ubuntu's input-kbd utility that stopped
returning full keymaps for remote controls.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Mark Lord <kernel@teksavvy.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: set queue DMA alignment to sector size for ATAPI too
libata: DVR-212D can't do SETXFER DVD-RW DVR-212D
ahci: add HFLAG_YES_FBS and apply it to 88SE9128
pata_hpt37x: inherit prereset() method for HPT374
ahci: AHCI mode SATA patch for Intel DH89xxCC DeviceIDs
pata_hpt37x: fold 'if' statement into 'switch'
pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)
pata_hpt{366|37x}: use pr_warning(...) instead of printk(KERN_WARNING ...)
pata_mpc52xx: inherit from ata_bmdma_port_ops
This error is reported by cppcheck:
drivers/gpu/drm/radeon/radeon_encoders.c:1066: warning: Mutual exclusion over || always evaluates to true. Did you intend to use && instead?
It looks like cppcheck is correct, so fix this. No test was run.
Cc: David Airlie <airlied@linux.ie>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix the referenced project website to www.mictronics.de in the Kconfig
help text for the slcan driver.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a121f64399.
Unfortunately, this commit breaks UBIFS backward compatibility and
makes new UBIFS refuse older UBIFS-formatted media:
UBIFS error: validate_sb: min. I/O unit mismatch: 8 in superblock, 64 real
Thus, we have to revert this patch and work on a better solution.
Reported-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
On some machines, like Dell Studio XPS 16 (1640), touchpad fails to
respond to the standard query after first reset but may start
responding later, so let's repeat reset sequence several (3) times.
Signed-off-by: Alexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
synaptics_set_advanced_gesture_mode() affect capabilities bits we should
perform comparison after calling this function, otherwise they will never
match and we will be forced to perform full reconnect.
Signed-off-by: Alexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit f06267104d ("RDMA: Update workqueue usage") introduced ib_wq
and removed the use of flush_scheduled_work(); however, during the merge
process one chunk was lost in ib_sa_remove_one(). Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For iWARP rdma_cm ids, the "route" information is the L2 src and
next hop addresses.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix compile warnings on 32-bit by using "0" instead of "(u64) NULL" to
assign to "c2_vq_req->reply_msg".
Signed-off-by: Ralf Thielow <ralf.thielow@googlemail.com>
[ Change from "(unsigned long) NULL" to plain old "0" as suggested by
Bart Van Assche <bvanassche@acm.org>. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
The PF passed to FW was 0, causing PCI failures in an SR-IOV environment.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
MAXBURST cannot exceed 256B for on-chip queues. With a 512B MAXBURST,
we can lock up the chip.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Hold the IB link at DISABLED until we get the correct TX settings
on mezz boards.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.
This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.
ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.
Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.
Cc: stable@kernel.org
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ata_pio_sectors() expects buffer for each sector to be contained in a
single page; otherwise, it ends up overrunning the first page. This
is achieved by setting queue DMA alignment. If sector_size is smaller
than PAGE_SIZE and all buffers are sector_size aligned, buffer for
each sector is always contained in a single page.
This wasn't applied to ATAPI devices but IDENTIFY_PACKET is executed
as ATA_PROT_PIO and thus uses ata_pio_sectors(). Newer versions of
udev issue IDENTIFY_PACKET with unaligned buffer triggering the
problem and causing oops.
This patch fixes the problem by setting sdev->sector_size to
ATA_SECT_SIZE on ATATPI devices and always setting DMA alignment to
sector_size. While at it, add a warning for the unlikely but still
possible scenario where sector_size is larger than PAGE_SIZE, in which
case the alignment wouldn't be enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: John Stanley <jpsinthemix@verizon.net>
Tested-by: John Stanley <jpsinthemix@verizon.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PIONEER DVR-212D can't do SETXFER like its sibling DVRTD08. Add
ATA_HORKAGE_NOSETXFER for it. Reported in bko#27502.
https://bugzilla.kernel.org/show_bug.cgi?id=27502
Signed-off-by: Francesco Antonacci <fraanto@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 5f173107ec added HFLAG_YES_FBS workaround for 88SE9128
(1b4b:9123).
However, that change inadvertently caused the legacy IDE interface of
the controller (with the same pci id) to become associated with the AHCI
driver as well, causing the driver to try to bring the interface up in
vain.
Fix that by matching against class as well.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit ab81a505ae (pata_hpt37x: unify ->pre_reset
methods) neglected to remove the initializer for the prereset() method from
'hpt374_fn1_port_ops' (it's inherited from 'hpt372_port_ops' anyway), as well
as to update the comment in hpt37x_init_one()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the AHCI-mode SATA DeviceID for the Intel DH89xxCC PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
hpt37x_init_one() has a large *if* statement which should really be folded into
the *switch* statement that currently constitutes its *else* branch, reducing
one level of indentation...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
... the same as the 'pata_hpt366' driver does.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_mpc52xx supports BMDMA but inherits ata_sff_port_ops which
triggers BUG_ON() when a DMA command is issued. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Roman Fietze <roman.fietze@telemotive.de>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/nv50: fix regression on IGPs
drm/radeon/kms: re-emit full context state for evergreen blits
drm/radeon/kms: release CMASK access in preclose_kms
drm/radeon/kms: fix r6xx+ scanout on BE systems
drm/radeon/kms: clean up some magic numbers
drm/radeon/kms: only enable HDMI mode if radeon audio is enabled
radeon/kms: fix dp displayport mode validation
drm/nvc0/grctx: correct an off-by-one
drm/nv50: Fix race with PFIFO during PGRAPH context destruction.
drm/nouveau: Workaround incorrect DCB entry on a GeForce3 Ti 200.
drm/nvc0: implement irq handler for whatever's at 0x14xxxx
drm/nvc0: fix incorrect TPC register setup
drm/nouveau: probe for adt7473 before f75375
drm/nouveau: remove dead function definition
clear state doesn't seem to work properly in some cases
Fixes hangs in heavy 3D on some evergreen cards reported on
IRC.
May fix:
https://bugs.freedesktop.org/show_bug.cgi?id=33381
possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@gmail.com>
The Linux network stack expects all GSO SKBs to have ip_summed ==
CHECKSUM_PARTIAL (which implies that the frame contains a partial
checksum) and the Xen network ring protocol similarly expects an SKB
which has GSO set to also have NETRX_csum_blank (which also implies a
partial checksum).
However there have been cases of buggy guests which mark a frame as
GSO but do not set csum_blank. If we detect that we a receiving such a
frame (which manifests as ip_summed != PARTIAL && skb_is_gso) then
force the SKB to partial and recalculate the checksum, since we cannot
rely on the peer having done so if they have not set csum_blank.
Add an ethtool stat to track occurances of this event.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: David Miller <davem@davemloft.net>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The MMCIDATACNT register contain the number of byte left at error
not the number of words, so loose the << 2 thing. Further if CRC
fails on the first block, we may end up with a negative number
of transferred bytes which is not good, and the formula was in
wrong order.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.
Cc: stable@kernel.org
Tested-by: Sujith <m.sujith@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.
I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath5k version of ieee80211_generic_frame_duration() returns
an __le16 for standard modes but a cpu-endian int for turbo/half/
quarter rates. Make it always return cpu-endian values.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Review spotted a problem with the error handling in ath5k_hw_dma_stop:
a successful return from ath5k_hw_stop_tx_dma will be treated as
an error, so we always bail out of the loop after processing a single
active queue. As a result, we may not actually stop some queues during
reset.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the source code from Realtek was prepared for kernel inclusion,
some routines were refactored to reduce the level of indentation. This
patch repairs errors introduced in that process.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (43 commits)
bnx2: Eliminate AER error messages on systems not supporting it
cnic: Fix big endian bug
xfrm6: Don't forget to propagate peer into ipsec route.
tg3: Use new VLAN code
bonding: update documentation - alternate configuration.
TCP: fix a bug that triggers large number of TCP RST by mistake
MAINTAINERS: remove Reinette Chatre as iwlwifi maintainer
rt2x00: add device id for windy31 usb device
mac80211: fix a crash in ieee80211_beacon_get_tim on change_interface
ipv6: Revert 'administrative down' address handling changes.
textsearch: doc - fix spelling in lib/textsearch.c.
USB NET KL5KUSB101: Fix mem leak in error path of kaweth_download_firmware()
pch_gbe: don't use flush_scheduled_work()
bnx2: Always set ETH_FLAG_TXVLAN
net: clear heap allocation for ethtool_get_regs()
ipv6: Always clone offlink routes.
dcbnl: make get_app handling symmetric for IEEE and CEE DCBx
tcp: fix bug in listening_get_next()
inetpeer: Use correct AVL tree base pointer in inet_getpeer().
GRO: fix merging a paged skb after non-paged skbs
...
R6xx+ have per-block swappers. BE content in the
framebuffer will now be swapped properly during scanout.
Untested, however, the same code is reported working in
the UMS ddx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Force DVI mode if the user specifies radeon.audio=0. The driver
doesn't handle HDMI mode properly in some cases.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=27731
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Check if there is a big enough dp clock & enough dp lane to
drive the video mode provided.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-By: Alex Deucher <alexdeucher@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Lucas Stach