Currently the SigmaDSP firmware loader only works correctly on little-endian
systems. Fix this by using the proper endianess conversion functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The firmware header is not part of the CRC, so skip it. Otherwise the firmware
will be rejected due to non-matching CRCs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The SigmaDSP firmware loader currently does not perform enough boundary size
checks when processing the firmware. As a result it is possible that a
malformed firmware can cause an out of bounds memory access.
This patch adds checks which ensure that both the action header and the payload
are completely inside the firmware data boundaries before processing them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This updates the Ux500 defconfig with the new drivers for HWSEM
and AB5500 core that were merged in the 3.2 cycle.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This updates the U300 defconfig to support some new drivers like
FSMC, sets it to use the MMC clock gating scheme, and removes
some stale config options.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added table quirks entry for Roland GAIA SH-01 Synthesizer based upon
Roland SH-201 table entry as template. USB MIDI and audio was tested
with Muse and Audacity.
Signed-off-by: John F Leach <jfleach@jfleach.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous commit 30c2235c is incomplete and cannot prevent integer
overflows. For example, when key_len is 0x80000000 (INT_MAX + 1), the
left-hand side of the check, (INT_MAX - key_len), which is unsigned,
becomes 0xffffffff (UINT_MAX) and bypasses the check.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prevents in-memory corruption and possible panics if the on-disk
ACL is badly corrupted.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: convert drivers/hwmon/* to use module_platform_driver()
hwmon: Remove redundant spi driver bus initialization
Support for the acm_ms usb gadget on windows.
Signed-off-by: Klaus Schwarzkopf <schwarzkopf@sensortherm.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a regression that was introduced by commit
811c926c53 (USB: EHCI: fix HUB TT scheduling
issue with iso transfer).
We detect an error if next == start, but this means uframe 0 can't be allocated
anymore for iso transfer...
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the case where CONFIG_PSTORE=n, the function efi_pstore_read() doesn't
have the correct list of parameters. This patch provides a definition
of efi_pstore_read() with 'char **buf' added to fix this warning:
"drivers/firmware/efivars.c:609: warning: initialization from".
problem introduced in commit f6f8285132
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We need to set np->mcast_hops to it's default value at this moment
otherwise when we use it and found it's value is -1, the logic to
get default hop limit doesn't take multicast into account and will
return wrong hop limit(IPV6_DEFAULT_HOPLIMIT) which is for unicast.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I just hit this during my testing. Isn't there another bug lurking?
BUG kmalloc-8: Redzone overwritten
INFO: 0xc0000000de9dec48-0xc0000000de9dec4b. First byte 0x0 instead of 0xcc
INFO: Allocated in .__seq_open_private+0x30/0xa0 age=0 cpu=5 pid=3896
.__kmalloc+0x1e0/0x2d0
.__seq_open_private+0x30/0xa0
.seq_open_net+0x60/0xe0
.dev_mc_seq_open+0x4c/0x70
.proc_reg_open+0xd8/0x260
.__dentry_open.clone.11+0x2b8/0x400
.do_last+0xf4/0x950
.path_openat+0xf8/0x480
.do_filp_open+0x48/0xc0
.do_sys_open+0x140/0x250
syscall_exit+0x0/0x40
dev_mc_seq_ops uses dev_seq_start/next/stop but only allocates
sizeof(struct seq_net_private) of private data, whereas it expects
sizeof(struct dev_iter_state):
struct dev_iter_state {
struct seq_net_private p;
unsigned int pos; /* bucket << BUCKET_SPACE + offset */
};
Create dev_seq_open_ops and use it so we don't have to expose
struct dev_iter_state.
[ Problem added by commit f04565ddf5 (dev: use name hash for
dev_seq_ops) -Eric ]
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-3.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: explain why per_cpu_ptr_to_phys() is more complicated than necessary
percpu: fix chunk range calculation
percpu: rename pcpu_mem_alloc to pcpu_mem_zalloc
The comments describing device power management callbacks in
include/pm.h are outdated and somewhat confusing, so make them
reflect the reality more accurately.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The system wakeup section of Documentation/power/devices.txt is
outdated, so make it agree with the current code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The runtime PM core code behavior related to the power.irq_safe
device flag has changed recently and the documentation should be
modified to reflect it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The documentation file Documentation/power/devices.txt contains some
information that isn't correct any more due to code modifications
made after that file had been created (or updated last time). Fix
this.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The current power management documentation in Documentation/power/
either doesn't cover PM domains at all, or gives inaccurate
information about them, so update the relevant files in there to
follow the code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Don't over-schedule QSFP work on driver initialization. It could end
up being run simultaneously on two different CPUs resulting in bad
EEPROM reads. In combination with setting the physical IB link state
prior to the IBC being brought out of reset, this can cause the link
state machine to start training early with wrong settings.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix logic so that we don't retry with MPAv1 once we have done that
already. Otherwise, we end up retrying with MPAv1 even when its not
needed on getting peer aborts - and this could lead to kernel panic.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix another place in the code where logic dealing with the t4_cqe was
using the wrong QID. This fixes the counting logic so that it tests
against the SQ QID instead of the RQ QID when counting RCQES.
Signed-off by: Jonathan Lallinger <jonathan@ogc.us>
Signed-off by: Steve Wise <swise@ogc.us>
Signed-off-by: Roland Dreier <roland@purestorage.com>
SMPS regulator voltage control differs from the one of the LDO ones.
Current TWL code was using LDO regulator ops for controlling the SMPS
regulators, which fails. This was fixed fixed by adding separate
regulator type which uses correct logic and calculations for the
voltage levels.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
When a packet is supposed to sent be as an a-MPDU, mac80211 sets
IEEE80211_TX_CTL_AMPDU to let the driver know. On the other
hand, mac80211 configures the driver for aggregration with the
ampdu_action callback.
There is race between these two mechanisms since the following
scenario can occur when the BA agreement is torn down:
Tx softIRQ drv configuration
========== =================
check OPERATIONAL bit
Set the TX_CTL_AMPDU bit in the packet
clear OPERATIONAL bit
stop Tx AGG
Pass Tx packet to the driver.
In that case the driver would get a packet with TX_CTL_AMPDU set
although it has already been notified that the BA session has been
torn down.
To fix this, we need to synchronize all the Qdisc activity after we
cleared the OPERATIONAL bit. After that step, all the following
packets will be buffered until the driver reports it is ready to get
new packets for this RA / TID. This buffering allows not to run into
another race that would send packets with TX_CTL_AMPDU unset while
the driver hasn't been requested to tear down the BA session yet.
This race occurs in practice and iwlwifi complains with a WARN_ON
when it happens.
Cc: stable@kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If addBA responses comes in just after addba_resp_timer has
expired mac80211 will still accept it and try to open the
aggregation session. This causes drivers to be confused and
in some cases even crash.
This patch fixes the race condition and makes sure that if
addba_resp_timer has expired addBA response is not longer
accepted and we do not try to open half-closed session.
Cc: stable@vger.kernel.org
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
[some adjustments]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Revert a hunk in drivers/net/wireless/ath/ath9k/hw.c introduced by
commit 2577c6e8f2 (ath9k_hw: Add
support for AR946/8x chipsets) that caused a nasty regression to
appear on my Acer Ferrari One (the box locks up entirely at random
times after the wireless has been started without any way to get
debug information out of it).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nikolay noticed (by code review) that mac80211 can
attempt to stop an aggregation session while it is
already being stopped. So to fix it, check whether
stop is already being done and bail out if so.
Also move setting the STOPPING state into the lock
so things are properly atomic.
Cc: stable@vger.kernel.org
Reported-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MAC addresses have a fixed length. The current
policy allows passing < ETH_ALEN bytes, which
might result in reading beyond the buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julian Sikorski reports NEC uPD720200 does not work stable after suspend
and resume. Re-initialize the host in xhci_resume().
This should be backported to stable kernels as old as 2.6.37. The
kernel will need to include
commit c877b3b2ad
"xhci: Add reset on resume quirk for asrock p67 host"
for this patch to work.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Reported-by: Julian Sikorski <belegdol@gmail.com>
Tested-by: Julian Sikorski <belegdol@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Fix extra wakeups from __remove_hrtimer()
timekeeping: add arch_offset hook to ktime_get functions
clocksource: Avoid selecting mult values that might overflow when adjusted
time: Improve documentation of timekeeeping_adjust()
Commit fa27271bc8d2("genirq: Fixup poll handling") introduced a
regression that broke irqfixup/irqpoll for some hardware configurations.
Amidst reorganizing 'try_one_irq', that patch removed a test that
checked for 'action->handler' returning IRQ_HANDLED, before acting on
the interrupt. Restoring this test back returns the functionality lost
since 2.6.39. In the current set of tests, after 'action' is set, it
must precede '!action->next' to take effect.
With this and my previous patch to irq/spurious.c, c75d720fca, all
IRQ regressions that I have encountered are fixed.
Signed-off-by: Edward Donovan <edward.donovan@numble.net>
Reported-and-tested-by: Rogério Brito <rbrito@ime.usp.br>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org (2.6.39+)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is caused by dereferencing 'rdev' after device_unregister() in
the regulator_unregister() function. 'rdev' is freed by
device_unregister(), so it must not be dereferenced after this call.
[Edited commit message for legibility -- broonie]
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In current implementation, the pointer ri is not NULL if no id is matched.
Fix it by checking i == ARRAY_SIZE(aat2870_regulators) if no id is matched.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Make it is safe to assign the return value of this function
to u8/u16 variables.
Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
To perform PHY calibration and set a different EA value by chip ID,
Whenever the NIC chip power on, ie booting or resuming, we need to
force HW to calibrate PHY parameter again, and also set a proper EA
value which gather from experiment.
Those procedures help to reduce compatible issues(NIC is unable to link
up in some special case) in giga speed.
Signed-off-by: AriesLee <AriesLee@jmicron.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'fbdev-for-linus' of git://github.com/schandinat/linux-2.6:
viafb: correct sync polarity for OLPC DCON
video:da8xx-fb: Disable and reset sequence on version2 of LCDC
OMAPDSS: DISPC: skip scaling calculations when not scaling
OMAPFB: fix compilation warnings due to missing include
OMAPDSS: HDMI: fix returned HDMI pixel clock
Takashi Iwai