The commit below didn't update the max_ht_ampdu_exponent
for the devices listed in iwl-[1-6]000.c which, in result,
became 0 instead of 8K. This reduced the size of the Rx
AMPDU from 64K to 8K which had an impact in the Rx
throughput. One user reported that because of this, his
downstream throughput droppped by a half.
CC: <stable@vger.kernel.org> [3.19]
Fixes: c064ddf318 ("iwlwifi: change max HT and VHT A-MPDU exponent")
Reported-and-tested-by: Valentin Manea <linux-wireless@mrs.ro>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
7000 device series have a fix for this hardware feature.
Stop disabling it, and get an improvement in Tx throughput.
This feature allows the scheduler to fetch more frames on
the fly while an A-MPDU is being built - which means that
we can get larger A-MPDU. This, of course, give an
improvement in the Tx throughput.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are a number of parameters that aren't really hardware
specific but rather define how the DVM firmware is used.
Move these into the DVM configuration.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer devices can work on different buses. This means that
their configuration can be shared between different buses.
Hence the configuration structures should exported to all
the buses and not only to PCIE. Change this.
Note that this requires all the fields to be the same
amongst the buses. If differences will appear, we can always
define a part that is bus dependent. Today, this is not
needed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Structure the code a bit more and move all PCIe code
including the hardware configuration files into a
PCIe specific subdirectory.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A workaround in commit c0486b7ccc5 resulted in a 40% drop in receive
throughput in order to fix a transmit problem. The transmit problem
no longer occurs, so restore the receive throughput.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
We can't get rid of everything yet due to
the BT definitions that I'm not quite sure
yet how to handle, but we can get rid of
most unneeded includes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The hardware files belong to the core PCI
functionality, but the eeprom header file
mixes higher-level functionality and the
defines, so move out the specific defines
and put them into the appropriate HW files
instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Having the pointer to lib_ops in the config
makes it impossible to split the driver into
different modules. Determine the ops based on
the device family enumeration to get rid of
the direct pointer.
Also move all the opmode specific code from
the iwl-[1256]000.c files into a new file
iwl-agn-devices.c so that the former only
have configuration data now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will later be used to dynamically bind
the configuration data for DVM and MVM.
For now, we can use it to get rid of the
additional_nic_config() hook.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hw_params are mostly values that are
derived from the actual hardware config.
As such, while it is possible that MVM
will require similar ones, it makes more
sense -- at least for now -- to put them
into the DVM struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes one of the two sources of device
restarts in the upper layer -- those are a bit
inconvenient because normal restarts originate
in the transport. By moving the watchdog down
it can be treated the same.
Also rewrite the watchdog logic. Timers are
much more efficient when they never fire, so
instead firing a timer every 500ms set up a
timer for each TX queue and fire it only when
the queue is really stuck. This avoids the CPU
waking up when everything is working well.
While at it, remove the wd_disable config item
and replace it by simply setting wd_timeout to
IWL_WATCHHDOG_DISABLED (0).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue mapping is not only dynamic, it
is also dependent on the uCode, as we can
already see today with the dual-mode and
non-dual-mode being different.
Move the queue mapping out of the transport
layer and let the higher layer manage it.
Part of the transport configuration is how
to set up the queues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BIg portion of "iwlwifi: remove max_txq_num from hw_params" was
missing during merge, here is the fix for it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sensitivity parameters are never modified, so they
should be const. Also remove the unused max_nrg_cck
value to save some space.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's only needed in a few places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW configuration settings base_params, ht_params
and bt_params all should be const, make it so.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a hardware parameter, so it shouldn't
be configurable by the user. Users can disable
aggregation (which is the only thing affected)
with 11n_disable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing to the global config structures
is always wrong. To protect against such
mistakes in the future, mark them const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not really a good idea to write to the
global static configuration. Use the valid
TX/RX antenna information only from the HW
params struct except in the case where the
values from the config are used to override
the values from the EEPROM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will allow to set the hw_params after we fetch the uCode.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There is nothing device specific in the initialization of the
bcast_sta_id so move it to the common inititalization routine.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
From now on, the transport layer in charge of providing access to the
device. So change all the driver to give a pointer to the transport
to all the low level functions that actually access the device.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move the configuration pointer from the upper level iwl_priv to the
lower level iwl_shared structure, with associated code fixes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current default watchdog timer is enabled, but we are seeing issues on
legacy devices. So change the default setting of watchdog timer to per
device based. But user still can use the "wd_disable" module parameter
to overwrite the system setting
Cc: stable@vger.kernel.org #3.0+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The init microcode knows very well which calibrations
are required and sends us results for those that are.
Consequently, we can just send all of those to the RT
uCode again.
The problem with having the driver know about this is
that it is a uCode feature, not a hardware feature so
the config is completely unsuitable.
The only thing we need to check is whether the device
needs crystal calibration or not, add a new parameter
to the configuration for that.
This makes new uCode work on 6000 series devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move iwl_enable_rfkill_int to iwl-core.h, and remove the empty
iwl-helpers.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After driver split, no need to separate station management functions
in two files, merge it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not needed since driver split.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's nothing PCI(E) specific in this file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All devices use the same value for beacon_time_tsf_bits. Use the #define
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
chain_noise_num_beacons is set and never changes. Use the #define
rather than 3 levels of indirection.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all the iwlXXX_abgn_cfg forward declaration to a separate file
so that iwl-pci.c doesn't need to include iwl-agn.h that includes
all iwl-dev.h
This allows to provide real encapsulation. Dereferencing iwl_priv
in the bus layer will now lead to a compilation error.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Which means that iwl-io.c doesn't need to include iwl-dev.h any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of them weren't used at all, the others always had the same value since
the driver split.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It will hold declaration of functions and forward declaration of struct that
are used by several layers.
This will allow modules not to include iwl_priv. iwl_bus and iwl_trans are
still visible to all.
All the layers share the module parameters, move the struct to iwl-shared.h.
Also add all module parameters to iwl_mod_params instead of having them as
global static. This includes
* debug_level
* ant_coupling
* bt_ch_announce
* wanted_ucode_alternative
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're working on improvements for the firmware
for some devices, and need to bump the API for
those since they won't be backward compatible
completely (the earlier patch reserving queue
10 for P2P).
Bump the API version to 6 for those devices
but don't warn users of version 5 yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For _bgn device, remove ht40 support for 5.2GHz, it is probably ok since
the "band" is not support but just feel strange.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1000 series are 1x2 devices, the old default using static smps which only
use single antenna for rx, set the default to dynamic smps.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
linux/wireless.h and net/iw_handler.h headers are
for wireless extensions only, so mac80211 drivers
shouldn't be including them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since iwlagn_setup_deferred_work is always called, fold it into
iwl_setup_deferred_work. BT related works are setup by the new
bt_setup_deferred_work lib_ops.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
Since iwlagn_rx_handler_setup is always called, fold it into
iwl_rx_handler_setup. BT related handlers are setup by the new
bt_rx_handler_setup lib_ops.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
Emmanuel Grumbach