NVIDIA's Tegra210 support the park bit to make pinmux configuration
enable/disable. If parked bit is 1 then configuration does not apply
and if it is 0 then pinmux configuration applies. This is to support
to avoid any glitch in pinmux configurations.
The parked bit is part of mux register and mux bank and hence it is
not required to have member for the parked_reg and parked bank very
similar to other bit field of the same register.
Remove the need of the parked register and parked bank and get whether
parked function supported or not by parked_bit.
This is to make the parked bit handling same as other fields of mux
registers.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pincontrol registers of Tegra chips has multiple filed per
registers. There is two type of registers mux and drive. All
configurations belongs to one of these registers.
If any configurations are supported then <config>_bit is set to
bit position of these registers otherwise -1 to not support it.
The member is defined as
s32 <config>_bit:6;
So if config is not supported ifor given SoC then it is set to -1
in soc pinmmux table.
In common driver code, to find out that given config is supported
or not, it is checked as:
s8 bit = <config>_bit;
if (bit > 31) {
/* Not supported config */
}
But in this case, bit is s8 and hence for non supporting it is -1.
Correct the check as:
if (bit < 0) {
/* Not supported config */
}
Fixes: e4c02dced9 ("pinctrl: tegra: use signed bitfields for optional fields")
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration and remove
need of .remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Parking bits might not be cleared by the bootloader properly (if for
instance it doesn't use the device configured by that pin). Clear
the park bits for all the pins during pinctrl probe.
This is present on T210 platforms but not earlier ones, so for earlier
generations, set parked_reg = -1 to disable.
The park bit is used to prevent glitching when reprogramming pinctrl
registers.
Based on work by:
Shravani Dingari <shravanid@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map, since
it does not depend on device tree despite the current name. This
will enforce a consistent naming in pinctr-utils.c and will make
it clear it can be called from outside device tree (e.g. from
ACPI handling code).
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra has several pinctrl drivers. Now it is reasonable enough to
move them into drivers/pinctrl/tegra/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij