Add support for updating firmware, triggered by a sysfs attribute.
This patch has been tested on Synaptics S7300.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 700a38b27e ("Input: gpio_keys - switch to using generic device
properties") switched to use generic device properties for GPIO keys and
commit 5feeca3c1e ("Input: gpio_keys - add support for GPIO descriptors")
switched from legacy GPIO numbers to GPIO descriptors.
Previously devm_gpio_request_one was explicitly passed GPIOF_DIR_IN flag
to set the GPIO direction as input. However devm_get_gpiod_from_child
doesn't have such provisions and hence fwnode_get_named_gpiod can't set
it as input.
This breaks few platforms with the following error:
" gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
unable to lock HW IRQ <n> for IRQ
genirq: Failed to request resources for POWER (irq <x>) on irqchip
gpio_keys: Unable to claim irq <x>; error -22
gpio-keys: probe failed with error -22 "
This patch fixes the issue by setting input direction explicitly for
gpio lines described by generic properties.
Fixes: 700a38b27e ("Input: gpio_keys - switch to using generic device properties")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should unlock before returning on this error path.
Fixes: 3a762dbd53 ('[media] Input: synaptics-rmi4 - add support for F54 diagnostics')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
BYD automatic protocol detection is extremely unreliable and is often
triggers false positives on regular mice, Sentelic touchpads, and other
devices. BYD has several documents that have recommended detection
sequence, but they conflict with each other and, as far as I can see, still
would not produce unique enough output to reliably differentiate BYD from
other PS/2 devices.
OEMs sourcing BYD devices also do not do us any favors by not supplying any
reasonable DMI data and instead leaving turds like "To Be Filled By O.E.M."
in place of vendor data, or "System Serial Number" as serial number.
On top of that BYD is not truly modern multitouch controller, but rather a
single-touch transitional device that only reports absolute coordinates at
the beginning of finger contact and then reverts to reporting
displacements, and thus not very precise; the only benefit from using BYD
mode vs the legacy PS/2 mode is possibility of edge scrolling.
Given the above, and the fact that BYD devices are somewhat uncommon, let's
disable automatic detection of BYD devices. Users who know they have BYD
trackpads or want to experiment can attempt to activate BYD protocol via
sysfs:
echo -n "byd" > /sys/bus/serio/devices/serio1/drvctl
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=151691
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=175421
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=120781
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=121281
Fixes: 98ee377144 ("Input: byd - add BYD PS/2 touchpad driver")
Cc: stable@vger.kernel.org # 4.6+
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Trivial fix to spelling mistake "failied" to "failed" in
dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some tablets the touchscreen controller is powered by separate
regulators, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit ef3714fdbc ("Input: bma150 - extend chip detection for bma180"),
adds bma180 chip-ids to the input bma150 driver, assuming that they are
100% compatible, but the bma180 is not compatible with the bma150 at all,
it has 14 bits resolution instead of 10, and it has quite different
control registers too.
Treating the bma180 as a bma150 wrt its data registers will just result
in throwing away the lowest 4 bits, which is not too bad. But the ctrl
registers are a different story. Things happen to just work but supporting
that certainly does not make treating the bma180 the same as the bma150
right.
Since some setups depend on the evdev interface the bma150 driver offers
on top of the bma180, we cannot simply remove the bma180 ids.
So this commit only removes the bma180 id when the bma180 iio driver,
which does treat the bma180 properly, is enabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The rmi4 2D sensor functions report the tool type via
input_mt_report_slot_state(), but the abs parameter bit has not been
set so the tool type is not reported to userspace. This patch set
the ABS_MT_TOOL_TYPE bit.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implements reading and setting the dribble bit in F12's control registers.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The rmi_f11 driver currently disables dribble packets and the palm detect
gesture for all devices. This patch creates a parameter in the 2d sensor
platform data for controlling this functionality on a per device basis.
For more information on dribble packets:
Commit 05ba999fca ("HID: rmi: disable dribble packets on Synaptics
touchpads")
For more information on the palm detect gesture:
Commit f097deef59 ("HID: rmi: disable palm detect gesture when present")
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 5b65c2a029 ("HID: rmi: check sanity of the incoming report") added
support for handling incomplete HID reports do to the input data being
corrupted in transit. This patch reimplements this functionality in the
function drivers so they can handle getting less valid data then they
expect.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The attn IRQ is related to the chip, rather than the transport, so move
all handling of interrupts to the core driver. This also makes sure that
there are no races between interrupts and availability of the resources
used by the core driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have encountered some RMI4 firmwares where there are blank pages in
between PDT pages which contain functions. This change makes them
correctly enumerate all functions on the device.
Tested on S7817 (has empty page 2).
Signed-off-by: Nick Dyer <nick@shmanahar.org>
[Tested successfully on S7817 and S7300 Synaptics touch controllers]
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make use of the device property API in this driver so that both OF based
systems and ACPI based systems can use this driver.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
GPIO descriptors are the preferred way over legacy GPIO numbers
nowadays. Convert the driver to use GPIO descriptors internally but
still allow passing legacy GPIO numbers from platform data to support
existing platforms.
Based on commits 633a21d80b ("input: gpio_keys_polled: Add support
for GPIO descriptors") and 1ae5ddb6f8 ("Input: gpio_keys_polled -
request GPIO pin as input.").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
for_each_available_child_of_node(node, pp) takes reference to 'pp' and
drops it when attempting next iteration. However if we exit the loop early
we need to drop the reference ourselves.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of using #ifdef, let's mark suspend and resume methods as
__maybe_unused to provide better compile coverage.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It does not matter if given GPIO may sleep or not when reading state,
polling is always done in a non-atomic context, so we should always
be able to simply use gpiod_get_value_cansleep().
Also let's note in the logs when we fail to read gpio state.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 633a21d80b ("input: gpio_keys_polled: Add support for GPIO
descriptors") placed gpio descriptor into gpio_keys_button structure, which
is supposed to be part of platform data and not modifiable by the driver.
To keep the data constant, let's move the descriptor to
gpio_keys_button_data structure instead.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use xenbus_read_unsigned() instead of xenbus_scanf() when possible.
This requires to change the type of the reads from int to unsigned,
but these cases have been wrong before: negative values are not allowed
for the modified cases.
Cc: dmitry.torokhov@gmail.com
Cc: linux-input@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/input/misc/da9063_onkey.ko | grep alias
alias: platform:da9063-onkey
After this patch:
$ modinfo drivers/input/misc/da9063_onkey.ko | grep alias
alias: platform:da9063-onkey
alias: of:N*T*Cdlg,da9062-onkeyC*
alias: of:N*T*Cdlg,da9062-onkey
alias: of:N*T*Cdlg,da9063-onkeyC*
alias: of:N*T*Cdlg,da9063-onkey
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/input/touchscreen/fsl-imx25-tcq.ko | grep alias
After this patch:
$ modinfo drivers/input/touchscreen/fsl-imx25-tcq.ko | grep alias
alias: of:N*T*Cfsl,imx25-tcqC*
alias: of:N*T*Cfsl,imx25-tcq
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
it's always easier to retrieve these information in bug reports when
it is always printed in the dmesg.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Older versions of gcc warn about the tca8418_irq_handler function
as they can't keep track of the variable assignment inside of the
loop when using the -Wmaybe-unintialized flag:
drivers/input/keyboard/tca8418_keypad.c: In function ‘tca8418_irq_handler’:
drivers/input/keyboard/tca8418_keypad.c:172:9: error: ‘reg’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/input/keyboard/tca8418_keypad.c:165:5: note: ‘reg’ was declared here
This is fixed in gcc-6, but it's possible to rearrange the code
in a way that avoids the warning on older compilers as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use product id for firmware name to request compatible firmware.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Copyright header is updated to add DA9061 in its description and the module
description macro is extended to include DA9061.
Minor change to the code, alters dev_dbg() statements to report a generic
"PMIC" instead of DA9063. This device driver is compatible with DA9061,
DA9062 and DA9063.
Kconfig is updated to reflect support for DA9061/62/63.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Trivial fix to typo in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
platform_device_id table is needed for adding the tps65218-pwrbutton
module to the mfd_cell array.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
psmouse->name "Focaltech Touchpad" is an overkill. In xinput it is too long
as "FocaltechPS/2 Focaltech Focaltech Touchpad"
In focaltech_report_state() pointer to psmouse->dev is already stored as
*dev
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of relying on this model zoo let's skip selftest on all newer Asus
laptops (newer as in when they changed "Computer" -> "COMPUTER" in their
DMI data).
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add product_id sysfs attribute and update protocol version to support it.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Schenker XMG C504 is a rebranded Gigabyte P35 v2 laptop.
Therefore it also needs a keyboard reset to detect the Elantech touchpad.
Otherwise the touchpad appears to be dead.
With this patch the touchpad is detected:
$ dmesg | grep -E "(i8042|Elantech|elantech)"
[ 2.675399] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.680372] i8042: Attempting to reset device connected to KBD port
[ 2.789037] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.791586] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.813840] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 3.811431] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f0e)
[ 3.825424] psmouse serio1: elantech: Synaptics capabilities query result 0x00, 0x15, 0x0f.
[ 3.839424] psmouse serio1: elantech: Elan sample query result 03, 58, 74
[ 3.911349] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input6
Signed-off-by: Patrick Scheuring <patrick.scheuring.dev@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull some more input subsystem updates from Dmitry Torokhov:
"An update to the ALPS driver to support the V8 protocol with
touchstick, a change for i8042 to skip selftest on many Asus laptops
which helps to keep their touchpads working after resume, and a couple
other driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - skip selftest on ASUS laptops
Input: melfas_mip4 - add ic_name sysfs attribute
Input: melfas_mip4 - add maintainer information
Input: melfas_mip4 - add devicetree binding documentations
Input: elantech - add Fujitsu Lifebook E556 to force crc_enabled
Input: synaptics-rmi4 - fix error handling in I2C transport driver
Input: synaptics-rmi4 - fix error handling in SPI transport driver
Input: ALPS - add V8 protocol documentation
Input: ALPS - set DualPoint flag for 74 03 28 devices
Input: ALPS - allow touchsticks to report pressure
Input: ALPS - handle 0-pressure 1F events
Input: ALPS - add touchstick support for SS5 hardware
Input: elantech - force needed quirks on Fujitsu H760
Input: elantech - fix Lenovo version typo
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX8Zc4AAoJEHm+PkMAQRiGQG8H/2Hd4IwJh75snGY5LAiWt6ra
kGM/SobvLAMtcoxXCeHqf2bZrxa2Zz9tnEzhuLMGaf9a3l79xHa8YumK5KS1JPGV
6lZBvuPi8BIyT0cpYH000e5ehHfhP6pSGJKZ2EuLv43HcBeVZEGAf3/8jSAlNA15
bwFy2ZEkwJGThbnT6au0Y3s9h8LcNjtllu9hjfb+/9oNGvp8r4QhdVodIqIQ4cv6
SeUfv7Pn2LZDMCSaTP9bh2KaR4dwYZHFsVe75x2wND5Sfq7DVBBfFkAoV/RwJDTM
gBc3PNnmzb/tix6ohOrSQnSiGsXv1uASxvHH3RD2zG6g7Aj9Eq/+Z7ZdPu2+o+U=
=U+ef
-----END PGP SIGNATURE-----
Merge tag 'v4.8' into next
Sync up with mainline to bring in I2C host notify changes and other
updates.
Merge more updates from Andrew Morton:
- a few block updates that fell in my lap
- lib/ updates
- checkpatch
- autofs
- ipc
- a ton of misc other things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (100 commits)
mm: split gfp_mask and mapping flags into separate fields
fs: use mapping_set_error instead of opencoded set_bit
treewide: remove redundant #include <linux/kconfig.h>
hung_task: allow hung_task_panic when hung_task_warnings is 0
kthread: add kerneldoc for kthread_create()
kthread: better support freezable kthread workers
kthread: allow to modify delayed kthread work
kthread: allow to cancel kthread work
kthread: initial support for delayed kthread work
kthread: detect when a kthread work is used by more workers
kthread: add kthread_destroy_worker()
kthread: add kthread_create_worker*()
kthread: allow to call __kthread_create_on_node() with va_list args
kthread/smpboot: do not park in kthread_create_on_cpu()
kthread: kthread worker API cleanup
kthread: rename probe_kthread_data() to kthread_probe_data()
scripts/tags.sh: enable code completion in VIM
mm: kmemleak: avoid using __va() on addresses that don't have a lowmem mapping
kdump, vmcoreinfo: report memory sections virtual addresses
ipc/sem.c: add cond_resched in exit_sme
...
On suspend/resume cycle, selftest is executed to reset i8042 controller.
But when this is done in Asus devices, subsequent calls to detect/init
functions to elantech driver fails. Skipping selftest fixes this problem.
An easier step to reproduce this problem is adding i8042.reset=1 as a
kernel parameter. On Asus laptops, it'll make the system to start with the
touchpad already stuck, since psmouse_probe forcibly calls the selftest
function.
This patch was inspired by John Hiesey's change[1], but, since this problem
affects a lot of models of Asus, let's avoid running selftests on them.
All models affected by this problem:
A455LD
K401LB
K501LB
K501LX
R409L
V502LX
X302LA
X450LCP
X450LD
X455LAB
X455LDB
X455LF
Z450LA
[1]: https://marc.info/?l=linux-input&m=144312209020616&w=2
Fixes: "ETPS/2 Elantech Touchpad dies after resume from suspend"
(https://bugzilla.kernel.org/show_bug.cgi?id=107971)
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=JqCR
-----END PGP SIGNATURE-----
Merge tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation improvements: conversion of all non-DocBook documents
to Sphinx and lots of fixes to the uAPI media book
- New PCI driver for Techwell TW5864 media grabber boards
- New SoC driver for ATMEL Image Sensor Controller
- Removal of some obsolete SoC drivers (s5p-tv driver and soc_camera
drivers)
- Addition of ST CEC driver
- Lots of drivers fixes, improvements and additions
* tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
[media] ttusb_dec: avoid the risk of go past buffer
[media] cx23885: Fix some smatch warnings
[media] si2165: switch to regmap
[media] si2165: use i2c_client->dev instead of i2c_adapter->dev for logging
[media] si2165: Remove legacy attach
[media] cx231xx: attach si2165 driver via i2c_client
[media] cx231xx: Prepare for attaching new style i2c_client DVB demod drivers
[media] cx23885: attach si2165 driver via i2c_client
[media] si2165: support i2c_client attach
[media] si2165: avoid division by zero
[media] rcar-vin: add R-Car gen2 fallback compatibility string
[media] lgdt3306a: remove 20*50 msec unnecessary timeout
[media] cx25821: Remove deprecated create_singlethread_workqueue
[media] cx25821: Drop Freeing of Workqueue
[media] cxd2841er: force 8MHz bandwidth for DVB-C if specified bw not supported
[media] redrat3: hardware-specific parameters
[media] redrat3: remove hw_timeout member
[media] cxd2841er: BER and SNR reading for ISDB-T
[media] dvb-usb: avoid link error with dib3000m{b,c|
[media] dvb-usb: split out common parts of dibusb
...
Another Lifebook machine that needs the same quirk as other similar
models to make the driver working.
Also let's reorder elantech_dmi_force_crc_enabled list so LIfebook enries
are in alphabetical order.
Reported-by: William Linna <william.linna@gmail.com>
Tested-by: William Linna <william.linna@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"You will get
- a new driver for Elan eKTF2127 touchscreen controllers
- a new "gpio-decoder" driver to read and report state of several
GPIO lines
- an ADC resistor ladder driver
- the ft6326 driver is removed because edt-ft5x06 handles the same
devices just fine.
.. plus the regular slew of driver fixes/enhancements"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (26 commits)
Input: elan_i2c - fix return tests of i2c_smbus_read_block_data()
Input: ektf2127 - mark PM functions as __maybe_unused
Input: snvs_pwrkey - drop input_free_device call if input_register_device fails
Input: add support for Elan eKTF2127 touchscreen controller
Input: serio - add hangup support
Input: tps65218-pwrbutton - add support for tps65217 variant
Input: jornada720_ts - get rid of mach/irqs.h and mach/hardware.h includes
Input: jornada720_kbd - remove unneeded mach/hardware.h include
Input: focaltech - mark focaltech_set_resolution() static
Input: wdt87xx_i2c - fix the flash erase issue
Input: gpio-keys-polled - don't use unit-address with button nodes
Input: add generic input driver to read encoded GPIO lines
Input: add ADC resistor ladder driver
Input: pegasus_notetaker - directly include workqueue header
Input: elants_i2c - get product id on recovery mode for FW update
Input: wm97xx - remove deprecated create_singletheread_workqueue
Input: mc13783_ts - remove deprecated create_singletheread_workqueue
Input: psmouse - remove deprecated create_singletheread_workqueue
Input: jornada720_kbd - switch to using dev_dbg
Input: jornada720_kbd - get rid of mach/irqs.h include
...
- Add the MFD bindings doc to MAINTAINERS
- New Drivers
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
- New Device Support
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
- New Functionality
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
- Fix-ups
- Clean-up defunct author emails; da9063, max14577
- Kconfig fixups; wm8350-i2c, as3722
- Constify; altera-a10sr, sm501
- Supply PCI IDs; intel-lpss-pci
- Improve clocking; qcom_rpm
- Fix IRQ probing; ucb1x00-core
- Ensure fault log is cleared; da9052
- Remove NO_IRQ check; ucb1x00-core
- Supply I2C properties; intel-lpss-acpi, intel-lpss-pci
- Non standard declaration; tps65217, max8997-irq
- Remove unused code; lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi
- Make non-modular; altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core,
- OF bindings; ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808,
axp20x, lp873x, exynos5433-lpass, act8945a,
aspeed-scu, twl6040, arizona
- Bug Fixes
- Release OF pointer; qcom_rpm
- Avoid double shifting in suspend/resume; 88pm80x
- Fix 'defined but not used' error; exynos-lpass
- Fix 'sleeping whilst attomic'; atmel-hlcdc
-----BEGIN PGP SIGNATURE-----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=Ja7p
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core framework:
- Add the MFD bindings doc to MAINTAINERS
New drivers:
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
New device support:
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
New functionality:
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
Fix-ups:
- Clean-up defunct author emails (da9063, max14577)
- Kconfig fixups (wm8350-i2c, as37220
- Constify (altera-a10sr, sm501)
- Supply PCI IDs (intel-lpss-pci)
- Improve clocking (qcom_rpm)
- Fix IRQ probing (ucb1x00-core)
- Ensure fault log is cleared (da9052)
- Remove NO_IRQ check (ucb1x00-core)
- Supply I2C properties (intel-lpss-acpi, intel-lpss-pci)
- Non standard declaration (tps65217, max8997-irq)
- Remove unused code (lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi)
- Make non-modular (altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core)
- OF bindings (ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808, axp20x,
lp873x, exynos5433-lpass, act8945a, aspeed-scu, twl6040, arizona)
Bugfixes:
- Release OF pointer (qcom_rpm)
- Avoid double shifting in suspend/resume (88pm80x)
- Fix 'defined but not used' error (exynos-lpass)
- Fix 'sleeping whilst attomic' (atmel-hlcdc)"
* tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: arizona: Handle probe deferral for reset GPIO
mfd: arizona: Remove arizona_of_get_named_gpio helper function
mfd: arizona: Add DT options for max_channels_clocked and PDM speaker config
mfd: twl6040: Register child device for twl6040-pdmclk
mfd: cros_ec_spi: Remove unused variable 'request'
mfd: omap-usb-host: Return value is not 'const int'
mfd: ab8500-debugfs: Remove 'weak' function suspend_test_wake_cause_interrupt_is_mine()
mfd: ab8500-debugfs: Remove ab8500_dump_all_banks_to_mem()
mfd: db8500-prcmu: Remove unused *prcmu_set_ddr_opp() calls
mfd: ab8500-debugfs: Prevent initialised field from being over-written
mfd: max8997-irq: 'inline' should be at the beginning of the declaration
mfd: rk808: Fix RK818_IRQ_DISCHG_ILIM initializer
mfd: tps65217: Fix nonstandard declaration
mfd: lp873x: Remove unused mutex lock from struct lp873x
mfd: atmel-hlcdc: Do not sleep in atomic context
mfd: exynos-lpass: Mark PM functions as __maybe_unused
mfd: intel-lpss: Add default I2C device properties for Apollo Lake
mfd: twl-core: Make it explicitly non-modular
mfd: sun6i-prcm: Make it explicitly non-modular
mfd: smsc-ece1099: Make it explicitly non-modular
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX8Zc4AAoJEHm+PkMAQRiGQG8H/2Hd4IwJh75snGY5LAiWt6ra
kGM/SobvLAMtcoxXCeHqf2bZrxa2Zz9tnEzhuLMGaf9a3l79xHa8YumK5KS1JPGV
6lZBvuPi8BIyT0cpYH000e5ehHfhP6pSGJKZ2EuLv43HcBeVZEGAf3/8jSAlNA15
bwFy2ZEkwJGThbnT6au0Y3s9h8LcNjtllu9hjfb+/9oNGvp8r4QhdVodIqIQ4cv6
SeUfv7Pn2LZDMCSaTP9bh2KaR4dwYZHFsVe75x2wND5Sfq7DVBBfFkAoV/RwJDTM
gBc3PNnmzb/tix6ohOrSQnSiGsXv1uASxvHH3RD2zG6g7Aj9Eq/+Z7ZdPu2+o+U=
=U+ef
-----END PGP SIGNATURE-----
Merge tag 'v4.8' into patchwork
Linux 4.8
* tag 'v4.8': (1761 commits)
Linux 4.8
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems
include/linux/property.h: fix typo/compile error
ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock()
mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()
MAINTAINERS: Switch to kernel.org email address for Javi Merino
x86/entry/64: Fix context tracking state warning when load_gs_index fails
x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUID
x86/vdso: Fix building on big endian host
x86/boot: Fix another __read_cr4() case on 486
sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock
sctp: change to check peer prsctp_capable when using prsctp polices
sctp: remove prsctp_param from sctp_chunk
sctp: move sent_count to the memory hole in sctp_chunk
tg3: Avoid NULL pointer dereference in tg3_io_error_detected()
x86/init: Fix cr4_init_shadow() on CR4-less machines
MIPS: Fix detection of unsupported highmem with cache aliases
MIPS: Malta: Fix IOCU disable switch read for MIPS64
MIPS: Fix BUILD_ROLLBACK_PROLOGUE for microMIPS
...
Instantiating the rmi4 I2C transport driver without interrupts assigned
(for example using manual i2c instantiation from the command line)
caused the driver to fail to load, but it does not clean up its regulator
or transport device registrations. Result is a crash at a later time,
for example when rebooting the system.
Fixes: 946c8432aa ("Input: synaptics-rmi4 - support regulator supplies")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instantiating the rmi4 SPI transport driver without an interrupt assigned
caused the driver to fail to load, but it does not clean up its transport
device registration. Result may be a crash at a later time, for example
when rebooting the system.
Fixes: 8d99758dee ("Input: synaptics-rmi4 - add SPI transport driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here we introduce logic in alps_identify to set the ALPS_DUALPOINT flag
for touchpad hardware responding to E7 report with 73 03 28, as is found
in the Dell Latitude E7470.
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The SS5 hardware can report this.
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
While a button is held SS5 hardware will give us single-finger packets
with x, y, and pressure equal to zero. This causes annoying jumps in
pointer position if a touch is released while the button is held. Handle
this by claiming zero contacts to ensure that no position events are
provided to the user.
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add touchstick support for the so-called SS5 hardware, which uses a
variant of the SS4 protocol.
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems that
flow through me. Nothing major that I can discern, full details are in
the shortlog.
All have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFUEABECABYFAlfyOIQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfsp9OQAlRy3
gSKfQUlXjTs96Bx/I5PtWysAn0r8nyKZoP1oSgsTddOCEeXngTXc
=4uPs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems
that flow through me. Nothing major that I can discern, full details
are in the shortlog.
All have been in the linux-next tree with no reported issues"
* tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (144 commits)
drivers/misc/hpilo: Changes to support new security states in iLO5 FW
at25: fix debug and error messaging
misc/genwqe: ensure zero initialization
vme: fake: remove unexpected unlock in fake_master_set()
vme: fake: mark symbols static where possible
spmi: pmic-arb: Return an error code if sanity check fails
Drivers: hv: get rid of id in struct vmbus_channel
Drivers: hv: make VMBus bus ids persistent
mcb: Add a dma_device to mcb_device
mcb: Enable PCI bus mastering by default
mei: stop the stall timer worker if not needed
clk: probe common clock drivers earlier
vme: fake: fix build for 64-bit dma_addr_t
ttyprintk: Neaten and simplify printing
mei: me: add kaby point device ids
coresight: tmc: mark symbols static where possible
coresight: perf: deal with error condition properly
Drivers: hv: hv_util: Avoid dynamic allocation in time synch
fpga manager: Add hardware dependency to Zynq driver
Drivers: hv: utils: Support TimeSync version 4.0 protocol samples.
...
Just like Fujitsu CELSIUS H730, the H760 also has an Elantech touchpad with
the same quirks. Without this patch, the touchpad is useless out-of-the-box
as the mouse pointer won't move.
This patch makes the driver aware of both the crc_enabled=1 requirement and
the middle button, making the touchpad fully functional out-of-the-box.
Signed-off-by: Matti Kurkela <Matti.Kurkela@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Reviewed-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i2c_smbus_read_block_data() returns negative errno else the number of
data bytes in the slave's response.
Checking for error not null means the function always fails if the device
answers properly.
So given that we read 3 bytes and access those, better check that we
actually read those 3 bytes.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The newly added ektf2127 driver uses the SIMPLE_DEV_PM_OPS macro
to conditionally refer to the resume/suspend functions, which
causes a warning when CONFIG_PM_SLEEP is disabled:
drivers/input/touchscreen/ektf2127.c:168:12: error: 'ektf2127_resume' defined but not used [-Werror=unused-function]
drivers/input/touchscreen/ektf2127.c:156:12: error: 'ektf2127_suspend' defined but not used [-Werror=unused-function]
We could either put these functions inside of an #ifdef or
add __maybe_unused annotations. This uses the second approach,
which is generally more foolproof.
Fixes: 9ca5bf5029 ("Input: add support for Elan eKTF2127 touchscreen controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fix from Dmitry Torokhov:
"One small change to make joydev (which is used by older games) to bind
to devices that export Z axis but not X or Y (such as TRC rudder)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: joydev - recognize devices with Z axis as joysticks
Current implementation of joydev's input_device_id table recognizes only
devices with ABS_X, ABS_WHEEL or ABS_THROTTLE axes as joysticks.
There are joystick devices that do not have those axes, for example TRC
Rudder device. The device in question has ABS_Z, ABS_RX and ABS_RY axes
causing it not being detected as joystick.
This patch adds ABS_Z to the input_device_id list allowing devices with
ABS_Z axis to be detected correctly.
Signed-off-by: Ville Ranki <ville.ranki@iki.fi>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Current code uses devm_input_allocate_device() so don't explicitly call
input_free_device if input_register_device fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds a driver for the Elan eKTF2127 touchscreen controller,
which speaks an i2c protocol which is distinctly different from
the already supported eKTH controllers.
Signed-off-by: Michel Verlaan <michel.verl@gmail.com>
Signed-off-by: Siebren Vroegindeweij <siebren.vroegindeweij@hotmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Just a fix up for the firmware handling to the Silead driver (which is
a new driver in this release)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: silead_gsl1680 - use "silead/" prefix for firmware loading
Input: silead_gsl1680 - document firmware-name, fix implementation
The Pulse-Eight USB CEC adapter is a usb device that shows up as a ttyACM0
device. It requires that you run inputattach in order to communicate with
it via serio.
This all works well, but it would be nice to have a udev rule to
automatically start inputattach. That too works OK, but the problem comes
when the USB device is unplugged: the tty hangup is never handled by the
serio framework so the inputattach utility never exits and you have to kill
it manually.
By adding this hangup callback the inputattach utility now properly exits
as soon as the USB device is unplugged.
The udev rule I used on my Debian sid system is:
SUBSYSTEM=="tty", KERNEL=="ttyACM[0-9]*", ATTRS{idVendor}=="2548", ATTRS{idProduct}=="1002", ACTION=="add", TAG+="systemd", ENV{SYSTEMD_WANTS}+="pulse8-cec-inputattach@%k.service"
And /etc/systemd/system/pulse8-cec-inputattach@.service is as follows:
===============================================================
[Unit]
Description=inputattach for pulse8-cec device on %I
[Service]
Type=simple
ExecStart=/usr/local/bin/inputattach --pulse8-cec /dev/%I
KillMode=process
===============================================================
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add copyright lines for Zodiac who paid for the V4L touch work.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The newly added debug mode for the synaptics-rmi4 driver relies on
the v4l2 interface and vb2_vmalloc, but those might be configured
as loadable modules when the driver itself is built-in, resulting
in a link failure:
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_remove':
rmi_f54.c:(.text.rmi_f54_remove+0x14): undefined reference to `video_unregister_device'
rmi_f54.c:(.text.rmi_f54_remove+0x20): undefined reference to `v4l2_device_unregister'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_s_input':
rmi_f54.c:(.text.rmi_f54_vidioc_s_input+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_g_input':
rmi_f54.c:(.text.rmi_f54_vidioc_g_input+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_fmt':
rmi_f54.c:(.text.rmi_f54_vidioc_fmt+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_enum_input':
rmi_f54.c:(.text.rmi_f54_vidioc_enum_input+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_querycap':
...
The best workaround I could come up with is to disallow the debug
mode unless it's actually possible to call it.
Fixes: 3a762dbd53 ("[media] Input: synaptics-rmi4 - add support for F54 diagnostics")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The newnly added debug mode for the atmel_mxt_ts driver relies on
the v4l2 interface and vb2_vmalloc, but those might be configured
as loadable modules when the driver itself is built-in, resulting
in a link failure:
drivers/input/touchscreen/atmel_mxt_ts.o: In function `mxt_vidioc_querycap':
atmel_mxt_ts.c:(.text.mxt_vidioc_querycap+0x10): undefined reference to `video_devdata'
drivers/input/touchscreen/atmel_mxt_ts.o: In function `mxt_buffer_queue':
atmel_mxt_ts.c:(.text.mxt_buffer_queue+0x20): undefined reference to `vb2_plane_vaddr'
atmel_mxt_ts.c:(.text.mxt_buffer_queue+0x164): undefined reference to `vb2_buffer_done'
drivers/input/touchscreen/atmel_mxt_ts.o: In function `mxt_free_object_table':
atmel_mxt_ts.c:(.text.mxt_free_object_table+0x18): undefined reference to `video_unregister_device'
atmel_mxt_ts.c:(.text.mxt_free_object_table+0x20): undefined reference to `v4l2_device_unregister'
The best workaround I could come up with is to disallow the debug
mode unless it's actually possible to call it.
Fixes: ecfdd7e266 ("[media] Input: atmel_mxt_ts - output diagnostic debug via V4L2 device")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The silead touch-controller ICs use a different firmware per digitizer /
tablet model. So there are going to be quite a few of then and they really
should be under a separate subdir.
This commit prefixes the default firmware names with "silead/" just like
we are already doing for devicetree specified firmware names.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver has supported touchscreen-fw-name to specify the firmware to
load since it has been merged, but this was omitted from the dt-binding
documentation.
During review of adding touchscreen-fw-name to the binding documentation
it was brought up that there is a standard property name called
"firmware-name" for this, which should be used.
Since there are no users of touchscreen-fw-name yet, this commit
adds documentation of "firmware-name" to the dt-binding documentation
and switches the driver over to use this.
This commit also makes the driver add a "silead/" prefix to the
firmware name from dt before calling request_firmware. That the
firmware files are stored under /lib/firmware/silead under Linux
is an implementation detail and does not belong in devicetree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The power button found in tps65217 device is very similar to the tps65218,
so let's enhance the driver to support both variants.
This driver enables us to use tps65217's power button as KEY_POWER on
am335x boards (directly connected button in chiliboard, accessible pin
via expansion header in beaglebone). This patch has been tested with
chiliboard.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch the jornada720 touchscreen driver to obtain its gpio from
the platform device via gpiolib and derive the interrupt from the
GPIO, rather than via a hard-coded interrupt number obtained from
the mach/irqs.h and mach/hardware.h headers.
Tested-by: Adam Wysocki <armlinux@chmurka.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Jornada720 keyboard driver does not make use of anything from the
mach/hardware.h header, so this header can be removed.
Tested-by: Adam Wysocki <armlinux@chmurka.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We get 1 warning when building kernel with W=1:
drivers/input/mouse/focaltech.c:393:6: warning: no previous prototype for 'focaltech_set_resolution' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
So this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The spec says that flash erase time is 30ms typical/200ms max, so let's
replace current 50ms wait with 200ms to avoid potential failures.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many modules call misc_register and misc_deregister in its module init
and exit methods without any additional code. This ends up being
boilerplate. This patch adds helper macro module_misc_device(), that
replaces module_init()/ module_exit() with template functions.
This patch also converts drivers to use new macro.
Change since v1:
Add device.h include in miscdevice.h as module_driver macro was not
available from other include files in some architectures.
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because events other that keyboard ones will be handled by now on by
other drivers, stop directly handling interrupts and instead listen to
the new notifier in the MFD driver.
Signed-off-by: Vic Yang <victoryang@google.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a driver to read group of GPIO lines and provide its status as a
numerical value as input event to the system. This will help in
interfacing devices, that can be connected over GPIOs, that provide
input to the system by driving GPIO lines connected to them like a
rotary dial or a switch.
For example, a rotary switch can be connected to four GPIO lines. The
status of the GPIO lines reflect the actual position of the rotary
switch dial. For example, if dial points to 9, then the four GPIO lines
connected to the switch will read HLLH(0b'1001 = 9). This value
can be reported as an ABS_* event to the input subsystem.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A common way of multiplexing buttons on a single input in cheap devices is
to use a resistor ladder on an ADC. This driver supports that configuration
by polling an ADC channel provided by IIO.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the kernel's guidelines, let's directly include the
workqueue functions we use.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We use hw version to construct name of file holding touchscreen firmware,
so let's try reading it even if touchscreen initialization fails (the
firmware supports reading product/hardware id even when device is in
recovery/boot mode).
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
alloc_ordered_workqueue() replaces deprecated
create_singlethread_workqueue().
It queues work items via &wm->ts_reader and &wm->pen_event_work which map
to wm97xx_pen_irq_worker (handles a pen down interrupt) and
wm97xx_ts_reader (the touchscreen sample reader) respectively. Hence, an
ordered dedicated workqueue has been used.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The workqueue "workqueue" has a single workitem(&priv->work) and hence
doesn't require ordering. Also, it is not being used on a memory reclaim
path. Hence, the singlethreaded workqueue has been replaced with the use
of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Workitem is sync cancelled in mc13783_ts_remove() to ensure that there
are no workitems pending when the driver is disconnected.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
alloc_ordered_workqueue() replaces the deprecated
create_singlethread_workqueue().
There are multiple work items on the work queue viz
&priv->dev3_register_work, &priv->recalib_wq, &psmouse->resync_work,
which require execution ordering. Hence, an ordered workqueue has been
used.
The workqueue is not being used on a memory reclaim path. Hence,
WQ_MEM_RECLAIM has not been set.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device hardware is always running at 60 FPS, so report this both via
PARM_IOCTL and ENUM_FRAMEINTERVALS.
[hans.verkuil@cisco.com: fix suspect indent checkpatch warning]
[mchehab@s-opensource.com: fix a trivial merge conflict]
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Support both V4L2_TCH_FMT_TU08 and V4L2_PIX_FMT_GREY for backwards
compatibility.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Function 54 implements access to various RMI4 diagnostic features.
This patch adds support for retrieving this data. It registers a V4L2
device to output the data to user space.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are different datatypes available from a maXTouch chip. Add
support to retrieve reference data as well.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The mXT1386 family of chips have a different architecture which splits
the diagnostic data into 3 columns.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Invert the diagnostic data to match the orientation of the input device.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen may have a margin where not all the matrix is used. Read
the parameters from T9 and T100 and take account of the difference.
Note: this does not read the XORIGIN/YORIGIN fields so it assumes that
the touchscreen starts at (0,0)
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Atmel maXTouch devices have a T37 object which can be used to read raw
touch deltas from the device. This consists of an array of 16-bit
integers, one for each node on the touchscreen matrix.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch to using dev_dbg instead of naked printk so that output is uniform
with the other driver messages in the kernel.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch the jornada720 keyboard driver to obtain its interrupt from the
platform device, rather than via a hard-coded interrupt number obtained
from the mach/irqs.h header.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch the jornada720_kbd driver to use the devm_* APIs. This is in
preparation to removing the mach/irqs.h include from this driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fix the following checkpatch report:
Blank lines aren't necessary after an open brace
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Checkpatch complains about the text suggesting writing to
Free Software Foundation for GPLv2 license copy.
This patch remove that text.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The usage of of_device_get_match_data reduce the code size a bit.
Furthermore, it is better to use a standard function for
getting the match data.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The new(ish) ft6236 simply re-implements the M09 protocol of the
(much) older edt-ft5x06.c driver.
This commit removes this duplicate driver and adds the i2c ids and
dt compatible string to the edt-ft5x06.c driver to keep compatibility.
This commit also adds the standard touchscreen properties as optional
properties to the edt,ft5x06 binding, these were documented in the
focaltech,ft6236 bindingi, but were missing from the edt,ft5x06 doc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ADS7846 regulator is disabled twice in a row in ads7846_remove(). Valid
one is in ads7846_disable().
Removing the ads7846 module causes warning about unbalanced disables.
...
WARNING: CPU: 0 PID: 29269 at drivers/regulator/core.c:2251 _regulator_disable+0xf8/0x130
unbalanced disables for vads7846
CPU: 0 PID: 29269 Comm: rmmod Tainted: G D W 4.7.0+ #3
Hardware name: HTC Magician
...
show_stack+0x10/0x14
__warn+0xd8/0x100
warn_slowpath_fmt+0x38/0x48
_regulator_disable+0xf8/0x130
regulator_disable+0x34/0x60
ads7846_remove+0x58/0xd4 [ads7846]
spi_drv_remove+0x1c/0x34
__device_release_driver+0x84/0x114
driver_detach+0x8c/0x90
bus_remove_driver+0x5c/0xc8
SyS_delete_module+0x1a0/0x238
ret_fast_syscall+0x0/0x38
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The map_offset variable is specific to the register and needs to be reset
in the loop. Otherwise, subsequent register's subpacket maps will have
their bits set at the wrong index.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Nitin Chaudhary <nitinchaudhary1289@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit fe6b0dfaba ("Input: tegra-kbc - use reset framework")
accidentally converted _deassert to _assert, so there is no code
to wake up this hardware.
Fixes: fe6b0dfaba ("Input: tegra-kbc - use reset framework")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The silead code is using devm_foo for everything (and does not free
any resources). Except that it is using gpiod_get instead of
devm_gpiod_get (but is not freeing the gpio_desc), change this
to use devm_gpiod_get so that the gpio will be properly released.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The commit 4097461897 ("Input: i8042 - break load dependency ...")
correctly set up ps2_cmd_mutex pointer for the KBD port but forgot to do
the same for AUX port(s), which results in communication on KBD and AUX
ports to clash with each other.
Fixes: 4097461897 ("Input: i8042 - break load dependency ...")
Reported-by: Bruno Wolff III <bruno@wolff.to>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input updates from Dmitry Torokhov:
"Two new drivers for touchscreen controllers:
- Silead touchscreen controllers
- SiS 9200 family touchscreen controllers
and a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: silead - remove some dead code
Input: sis-i2c - select CONFIG_CRC_ITU_T
Input: add driver for SiS 9200 family I2C touchscreen controllers
Input: ili210x - fix permissions on "calibrate" attribute
Input: elan_i2c - properly wake up touchpad on ASUS laptops
Input: add driver for Silead touchscreens
Input: elantech - fix debug dump of the current packet
Input: rotary_encoder - support binary encoding of states
Input: xpad - power off wireless 360 controllers on suspend
Input: i8042 - break load dependency between atkbd/psmouse and i8042
Input: synaptics-rmi4 - do not check for NULL when calling of_node_put()
Input: cros_ec_keyb - cleanup use of dev
buf[0] is an unsigned char. touch_nr is an int. The test for negative
here doesn't make sense so I have removed it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The newly added sis_i2c driver fails to link without the CRC_ITU_T
driver enabled:
drivers/input/touchscreen/sis_i2c.o: In function `sis_ts_irq_handler':
sis_i2c.c:(.text+0xc0): undefined reference to `crc_itu_t'
This adds a Kconfig select statement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a485cb037f ("Input: add driver for SiS 9200 family I2C touchscreen controllers")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a driver for SiS 9200 family touchscreen controllers using I2C bus.
Signed-off-by: Mika Penttilä <mika.penttila@nextfour.com>
Acked-by: Tammy Tseng <tammy_tseng@sis.com>
Acked-by: Yuger Yu <yuger_yu@sis.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
"calibrate" attribute does not provide "show" methods and thus we should
not mark it as readable.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some ASUS laptops were shipped with touchpads that require to be woken up
first, before trying to switch them into absolute reporting mode, otherwise
touchpad would fail to work while flooding the logs with:
elan_i2c i2c-ELAN1000:00: invalid report id data (1)
Among affected devices are Asus E202SA, N552VW, X456UF, UX305CA, and
others. We detect such devices by checking the IC type and product ID
numbers and adjusting order of operations accordingly.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Reported-by: Chris Chiu <chiu@endlessm.com>
Reported-by: Vlad Glagolev <stealth@vaygr.net>
Tested-by: Vlad Glagolev <stealth@vaygr.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver adds support for Silead touchscreens. It has been tested
with GSL1680 and GSL3680 touch panels.
It supports ACPI and device tree enumeration. Screen resolution,
the maximum number of fingers supported and firmware name are
configurable.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Daniel Jansen <djaniboe@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The use of mixed psmouse_printk() and printk creates 2 lines in the log,
while the use of %*ph solves everything.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
It's not advisable to use this encoding, but to support existing devices
add support for this to the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the USB wireless adapter is suspended, the controllers
lose their connection. This causes them to start flashing
their LED rings and searching for the wireless adapter
again, wasting the controller's battery power.
Instead, we will tell the controllers to power down when
we suspend. This mirrors the behavior of the controllers
when connected to the console itself and how the official
Xbox One wireless adapter behaves on Windows.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Updates for the input subsystem. This contains the following new
drivers promised in the last merge window:
- driver for touchscreen controller found in Surface 3
- driver for Pegasus Notetaker tablet
- driver for Atmel Captouch Buttons
- driver for Raydium I2C touchscreen controllers
- powerkey driver for HISI 65xx SoC
plus a few fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
Input: tty/vt/keyboard - use memdup_user()
Input: pegasus_notetaker - set device mode in reset_resume() if in use
Input: pegasus_notetaker - cancel workqueue's work in suspend()
Input: pegasus_notetaker - fix usb_autopm calls to be balanced
Input: pegasus_notetaker - handle usb control msg errors
Input: wacom_w8001 - handle errors from input_mt_init_slots()
Input: wacom_w8001 - resolution wasn't set for ABS_MT_POSITION_X/Y
Input: pixcir_ts - add support for axis inversion / swapping
Input: icn8318 - use of_touchscreen helpers for inverting / swapping axes
Input: edt-ft5x06 - add support for inverting / swapping axes
Input: of_touchscreen - add support for inverted / swapped axes
Input: synaptics-rmi4 - use the RMI_F11_REL_BYTES define in rmi_f11_rel_pos_report
Input: synaptics-rmi4 - remove unneeded variable
Input: synaptics-rmi4 - remove pointer to rmi_function in f12_data
Input: synaptics-rmi4 - support regulator supplies
Input: raydium_i2c_ts - check CRC of incoming packets
Input: xen-kbdfront - prefer xenbus_write() over xenbus_printf() where possible
Input: fix a double word "is is" in include/linux/input.h
Input: add powerkey driver for HISI 65xx SoC
Input: apanel - spelling mistake - "skiping" -> "skipping"
...
As explained in 1407814240-4275-1-git-send-email-decui@microsoft.com we
have a hard load dependency between i8042 and atkbd which prevents
keyboard from working on Gen2 Hyper-V VMs.
> hyperv_keyboard invokes serio_interrupt(), which needs a valid serio
> driver like atkbd.c. atkbd.c depends on libps2.c because it invokes
> ps2_command(). libps2.c depends on i8042.c because it invokes
> i8042_check_port_owner(). As a result, hyperv_keyboard actually
> depends on i8042.c.
>
> For a Generation 2 Hyper-V VM (meaning no i8042 device emulated), if a
> Linux VM (like Arch Linux) happens to configure CONFIG_SERIO_I8042=m
> rather than =y, atkbd.ko can't load because i8042.ko can't load(due to
> no i8042 device emulated) and finally hyperv_keyboard can't work and
> the user can't input: https://bugs.archlinux.org/task/39820
> (Ubuntu/RHEL/SUSE aren't affected since they use CONFIG_SERIO_I8042=y)
To break the dependency we move away from using i8042_check_port_owner()
and instead allow serio port owner specify a mutex that clients should use
to serialize PS/2 command stream.
Reported-by: Mark Laws <mdl@60hz.org>
Tested-by: Mark Laws <mdl@60hz.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mrOW
-----END PGP SIGNATURE-----
Merge tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new framework support for HDMI CEC and remote control support
- new encoding codec driver for Mediatek SoC
- new frontend driver: helene tuner
- added support for NetUp almost universal devices, with supports
DVB-C/S/S2/T/T2 and ISDB-T
- the mn88472 frontend driver got promoted from staging
- a new driver for RCar video input
- some soc_camera legacy drivers got removed: timb, omap1, mx2, mx3
- lots of driver cleanups, improvements and fixups
* tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (377 commits)
[media] cec: always check all_device_types and features
[media] cec: poll should check if there is room in the tx queue
[media] vivid: support monitor all mode
[media] cec: fix test for unconfigured adapter in main message loop
[media] cec: limit the size of the transmit queue
[media] cec: zero unused msg part after msg->len
[media] cec: don't set fh to NULL in CEC_TRANSMIT
[media] cec: clear all status fields before transmit and always fill in sequence
[media] cec: CEC_RECEIVE overwrote the timeout field
[media] cxd2841er: Reading SNR for DVB-C added
[media] cxd2841er: Reading BER and UCB for DVB-C added
[media] cxd2841er: fix switch-case for DVB-C
[media] cxd2841er: fix signal strength scale for ISDB-T
[media] cxd2841er: adjust the dB scale for DVB-C
[media] cxd2841er: provide signal strength for DVB-C
[media] cxd2841er: fix BER report via DVBv5 stats API
[media] mb86a20s: apply mask to val after checking for read failure
[media] airspy: fix error logic during device register
[media] s5p-cec/TODO: add TODO item
[media] cec/TODO: drop comment about sphinx documentation
...
The of_node_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In cros_ec_keyb we stored "dev" in "struct cros_ec_keyb", but this was
the EC's dev pointer and not the keyboard's. Let's clean this up to
make it the keyboard's dev pointer. This could be useful in future
patches but also has the nice effect of changing a few printouts to
include the name of the keyboard device instead of the EC device, so we
will see:
[ 1.224648] cros-ec-keyb ff110000.spi:ec@0:keyboard-controller: valid_keys[00] = 0x14
instead of:
[ 1.224505] cros-ec-spi spi0.0: valid_keys[00] = 0x14
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A few more fixes for the input subsystem:
- restore naming for tsc2005 touchscreens as some userspace match on it
- fix out of bound access in legacy keyboard driver
- fixup in RMI4 driver
Everything is tagged for stable as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc200x - report proper input_dev name
tty/vt/keyboard: fix OOB access in do_compute_shiftstate()
Input: synaptics-rmi4 - fix maximum size check for F12 control register 8
Passes input_id struct to the common probe function for the tsc200x drivers
instead of just the bustype.
This allows for the use of the product variable to set the input_dev->name
variable according to the type of touchscreen used. Note that when we
introduced support for TSC2004 we started calling everything TSC200X, so
let's keep this quirk.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Cc: stable@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the RMI4 spec the maximum size of F12 control register 8 is
15 bytes. The current code incorrectly reports an error if control 8 is
greater then 14. Making sensors with a control register 8 with 15 bytes
unusable.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reported-by: Chris Healy <cphealy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should only "put" the interface if submitting URB or setting tablet mode
in pegasus_open() fails, otherwise leave it to pegasus_close().
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() may fail and we should be handling failures properly.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A few last-minute updates for the input subsystem"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ts4800-ts - add missing of_node_put after calling of_parse_phandle
Input: synaptics-rmi4 - use of_get_child_by_name() to fix refcount
Revert "Input: wacom_w8001 - drop use of ABS_MT_TOOL_TYPE"
Input: xpad - validate USB endpoint count during probe
Input: add SW_PEN_INSERTED define
Add support for axis inversion / swapping using the new
touchscreen_parse_properties() and touchscreen_set_mt_pos()
functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the touchscreen_parse_properties() and touchscreen_report_pos() to
perform coordinates transformation, instead of DIY code, which results in a
nice cleanup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for inverting / swapping axes using the new
touchscreen_parse_properties() and touchscreen_report_pos()
functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Extend touchscreen_parse_properties() with support for the
touchscreen-inverted-x/y and touchscreen-swapped-x-y properties and
add touchscreen_set_mt_pos() and touchscreen_report_pos() helper
functions for storing coordinates into a input_mt_pos struct, or
directly reporting them, taking these properties into account.
This commit also modifies the existing callers of
touchscreen_parse_properties() to pass in NULL for the new third
argument, keeping the existing behavior.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The size of relative data in F11 is already defined by RMI_F11_REL_BYTES.
Use the define in rmi_f11_rel_pos_report() to be consistent.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove the data_base_addr_offset variable in rmi_f11_attention(). The
f11 data is read as a single block so there is no need to store an offset
to the data address.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The pointer to struct rmi_function in f12_data is never set and was never
used. The fn pointer is also stored in rmi_2d_sensor which is a member of
f12_data.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Calling of_find_node_by_name() assumes that the caller has incremented
the refcount of the of_node being passed in. Currently, the caller is
not incrementing the refcount of the of_node which results in the node
being prematurely freed when of_find_node_by_name() calls of_node_put()
on it. Instead use of_get_child_by_name() which does not call put on the
of_node.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 5f7e5445a2 because
removal of input_mt_report_slot_state() means we no longer generate
tracking IDs for the reported contacts.
Cc: stable@vger.kernel.org
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Ping Cheng <pinglinux@gmail.com>
Support the two supplies - vdd and vio - to make it possible to control
power to the Synaptics chip.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Check CRC of incoming touch packets to ensure that we do not operate on
corrupted data.
Signed-off-by: Jeffrey Lin <jeffrey.lin@rad-ic.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXefulAAoJEHm+PkMAQRiG6nMH/2O1vcZeOtqmx2yCMUeXyKAT
wG88XflXzf3rM7C7TiObEYVf/bbLleJ7saDLEeic7ButD5gyYacIuzylVnrcqfBc
vinz4cOw5kvu9DrRkCKdOfiTAgwYtqQW+syJ8ZK4lPQuSxnPAs+F/FKSOpyUF5FN
Dngr520KjYKBEtn27W9UDPChFRwQoWAlaOC534eusaArCJtHGHHiuq5TEDn2EIo8
pUw2vwx5JiquSHOY34WLU7r+QoilovCQlUSsBQdLlPjfMB1QFtclPYa+5yEMjkT4
wusOUOfS/zK0rV6KnEdc/SkpiVX5C9WpFiWUOdEeJ5mZ+KijVkaOa9K1EDx8jSM=
=7Hwh
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rc6' into patchwork
Linux 4.7-rc6
* tag 'v4.7-rc6': (1245 commits)
Linux 4.7-rc6
ovl: warn instead of error if d_type is not supported
MIPS: Fix possible corruption of cache mode by mprotect.
locks: use file_inode()
usb: dwc3: st: Use explicit reset_control_get_exclusive() API
phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
phy: miphy28lp: Inform the reset framework that our reset line may be shared
namespace: update event counter when umounting a deleted dentry
9p: use file_dentry()
lockd: unregister notifier blocks if the service fails to come up completely
ACPI,PCI,IRQ: correct operator precedence
fuse: serialize dirops by default
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
powerpc: Initialise pci_io_base as early as possible
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
...
Don't fill in the format description. This is now done in the V4L2 core to ensure
consistent descriptions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Closing the V4L2 device sometimes triggers a kernel oops.
Present patch fixes this.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.2 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The framerate sometimes drops below 60 Hz if the poll interval is too high.
Lowering it to the minimum of 1 ms fixes this.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.2 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stop using alloc_ctx and just fill in the device pointer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch changes the compatibility string to match with the smallest
supported chip (EP7209). Since the DT-support for this CPU is not yet
announced, this change is safe.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This prevents a malicious USB device from causing an oops.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: vmmouse - remove port reservation
Input: elantech - add more IC body types to the list
Input: wacom_w8001 - ignore invalid pen data packets
Input: wacom_w8001 - w8001_MAX_LENGTH should be 13
Input: xpad - fix oops when attaching an unknown Xbox One gamepad
MAINTAINERS: add Pali Rohár as reviewer of ALPS PS/2 touchpad driver
Input: add HDMI CEC specific keycodes
Input: add BUS_CEC type
Input: xpad - fix rumble on Xbox One controllers with 2015 firmware
The VMWare EFI BIOS will expose port 0x5658 as an ACPI resource. This
causes the port to be reserved by the APCI module as the system comes up,
making it unavailable to be reserved again by other drivers, thus
preserving this VMWare port for special use in a VMWare guest.
This port is designed to be shared among multiple VMWare services, such as
the VMMOUSE. Because of this, VMMOUSE should not try to reserve this port
on its own.
The VMWare non-EFI BIOS does not do this to preserve compatibility with
existing/legacy VMs. It is known that there is small chance a VM may be
configured such that these ports get reserved by other non-VMWare devices,
and if this ever happens, the result is undefined.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: <stable@vger.kernel.org> # 4.1-
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver provides a input driver for the power button on the
HiSi 65xx SoC for boards like HiKey.
This driver was originally by Zhiliang Xue <xuezhiliang@huawei.com>
then basically rewritten by Jorge, but preserving the original
module author credits.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
[jstultz: Reworked commit message, folded in other fixes/cleanups
from Jorge, implemented some larger cleanups suggested by DmitryT]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchpad in HP Pavilion 14-ab057ca reports it's version as 12 and
according to Elan both 11 and 12 are valid IC types and should be
identified as hw_version 4.
Reported-by: Patrick Lessard <Patrick.Lessard@cogeco.com>
Tested-by: Patrick Lessard <Patrick.Lessard@cogeco.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ThinkPad X60 Tablet PC (pen only device) sometime posts
packets that are larger than W8001_PKTLEN_TPCPEN.
Reported-by: Chris J Arges <christopherarges@gmail.com>
Tested-by: Chris J Arges <christopherarges@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Somehow the patch that added two-finger touch support forgot to update
W8001_MAX_LENGTH from 11 to 13.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
trivial fix to spelling mistake in pr_notice message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
trivial fix to spelling mistake in dev_warn message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Xbox One controllers have multiple interfaces which all have the
same class, subclass, and protocol. One of the these interfaces
has only a single endpoint. When Xpad attempts to bind to this
interface, it causes an oops when trying initialize the output URB
by trying to access the second endpoint's descriptor.
This situation was avoided for known Xbox One devices by checking
the XTYPE constant associated with the VID and PID tuple. However,
this breaks when new or previously unknown Xbox One controllers
are attached to the system.
This change addresses the problem by deriving the XTYPE for Xbox
One controllers based on the interface protocol before checking
the interface number.
Fixes: 1a48ff81b3 ("Input: xpad - add support for Xbox One controllers")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch changes name of secondary psmouse devices to mach format of
primary device. Format of primary device is "protocol vendor name" and is
set by function psmouse_switch_protocol() in file psmouse-base.c.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds a driver for the Pegasus Notetaker Pen. When connected,
this uses the Pen as an input tablet.
This device was sold in various different brandings, for example
"Pegasus Mobile Notetaker M210",
"Genie e-note The Notetaker",
"Staedtler Digital ballpoint pen 990 01",
"IRISnotes Express" or
"NEWLink Digital Note Taker".
Here's an example, so that you know what we are talking about:
http://www.genie-online.de/genie-e-note-2/https://pegatech.blogspot.com/ seems to be a remaining official resource.
This device can also transfer saved (offline recorded handwritten) data and
there are userspace programs that do this, see https://launchpad.net/m210
(Well, alternatively there are really fast scanners out there :)
It's *really* fun to use as an input tablet though! So let's support this
for everybody.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Xbox One controllers that shipped with or were upgraded to the 2015
firmware discard the current rumble packets we send. This patch changes
the Xbox One rumble packet to a form that both the newer and older
firmware will accept.
It is based on changes made to support newer Xbox One controllers in
the SteamOS brewmaster-4.1 kernel branch.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the code formatting to use the kernel preferred style
of using the actual variables to determize the size using
the sizeof() operator.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For devices that are incapable of reporting per-contact distance and can
only report ABS_DISTANCE, just distance is not enough for upper layers of
OS to determine whether contact is leaving the area or if it is continuing
hovering, we need BTN_TOOL_FINGER for that:
Contact State
Inactive Hovering Active
(far away) (inside hover area) (touching surface)
BTN_TOUCH 0 0 1
BTN_TOOL_FINGER 0 1 1
ABS_DISTANCE N/A 1 0
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should not be ignoring -EPROBE_DEFER reported by
devm_gpiod_get_optional(), but report it as any other error to the upper
layers. While we are at it simplify check for the presence of reset GPIO
and instead of using IS_ERR_OR_NULL just use boolean.
Also do not return -ENOMEM from suspend handler when the device in
bootloader mode as that does not make sense and switch to -EBUSY instead.
Reported-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input subsystem updates from Dmitry Torokhov:
"Just a few more driver fixes; new drivers will be coming in the next
merge window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: pwm-beeper - fix - scheduling while atomic
Input: xpad - xbox one elite controller support
Input: xpad - add more third-party controllers
Input: xpad - prevent spurious input from wired Xbox 360 controllers
Input: xpad - move pending clear to the correct location
Input: uinput - handle compat ioctl for UI_SET_PHYS
This adds support for Raydium I2C touch controllers compatible with
RM32380.
Signed-off-by: Jeffrey Lin <jeffrey.lin@rad-ic.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pwm config may sleep so defer it using a worker.
On a Freescale i.MX53 based board we ran into "BUG: scheduling while
atomic" because input_inject_event locks interrupts, but
imx_pwm_config_v2 sleeps.
Tested on Freescale i.MX53 SoC with 4.6.0.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change creates a second input device which will handle input from
a Surface Pen. The Surface Pen supplies a different packet header than
touch events, so it is simple to handle one or the other.
This patch handles both the newer Surface Pen with one button, and the
older variant with a second button to switch to Eraser mode.
Signed-off-by: Stephen Just <stephenjust@gmail.com>
Reviewed-and-tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Surface Pens can be supported by handling a second report type. Prepare
for this change.
Signed-off-by: Stephen Just <stephenjust@gmail.com>
Reviewed-and-tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
added the according id and incresed XPAD_PKT_LEN to 64 as the elite
controller sends at least 33 byte messages [1].
Verified to be working by [2].
[1]: https://franticrain.github.io/sniffs/XboxOneSniff.html
[2]: https://github.com/paroj/xpad/issues/23
Signed-off-by: Pierre-Loup A. Griffais <eduke32@plagman.net>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After initially connecting a wired Xbox 360 controller or sending it
a command to change LEDs, a status/response packet is interpreted as
controller input. This causes the state of buttons represented in
byte 2 of the controller data packet to be incorrect until the next
valid input packet. Wireless Xbox 360 controllers are not affected.
Writing a new value to the LED device while holding the Start button
and running jstest is sufficient to reproduce this bug. An event will
come through with the Start button released.
Xboxdrv also won't attempt to read controller input from a packet
where byte 0 is non-zero. It also checks that byte 1 is 0x14, but
that value differs between wired and wireless controllers and this
code is shared by both. I think just checking byte 0 is enough to
eliminate unwanted packets.
The following are some examples of 3-byte status packets I saw:
01 03 02
02 03 00
03 03 03
08 03 00
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull thermal management updates from Zhang Rui:
- Introduce generic ADC thermal driver, based on OF thermal (Laxman
Dewangan)
- Introduce new thermal driver for Tango chips (Marc Gonzalez)
- Rockchip driver support for RK3399, RK3366, and some fixes (Caesar
Wang, Elaine Zhang and Shawn Lin)
- Add CPU power cooling model to Mediatek thermal driver (Dawei Chien)
- Wider usage of dev_thermal_zone_of_sensor_register (Eduardo Valentin)
- TI thermal driver gained a new maintainer (Keerthy).
- Enabled powerclamp driver by checking CPU feature and package cstate
counter instead of CPU whitelist (Jacob Pan)
- Various fixes on thermal governor, OF thermal, Tegra, and RCAR
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (50 commits)
thermal: tango: initialize TEMPSI_CFG
thermal: rockchip: use the usleep_range instead of udelay
thermal: rockchip: add the notes for better reading
thermal: rockchip: Support RK3366 SoCs in the thermal driver
thermal: rockchip: handle the power sequence for tsadc controller
thermal: rockchip: update the tsadc table for rk3399
thermal: rockchip: fixes the code_to_temp for tsadc driver
thermal: rockchip: disable thermal->clk in err case
thermal: tegra: add Tegra132 specific SOC_THERM driver
thermal: fix ptr_ret.cocci warnings
thermal: mediatek: Add cpu dynamic power cooling model.
thermal: generic-adc: Add ADC based thermal sensor driver
thermal: generic-adc: Add DT binding for ADC based thermal sensor
thermal: tegra: fix static checker warning
thermal: tegra: mark PM functions __maybe_unused
thermal: add temperature sensor support for tango SoC
thermal: hisilicon: fix IRQ imbalance enabling
thermal: hisilicon: support to use any sensor
thermal: rcar: Remove binding docs for r8a7794
thermal: tegra: add PM support
...
The end ')' needs to be removed if the macro is ever used or there
would be a compiler error as it does not have a matching '('.
Signed-off-by: Clifton Barnes <clifton.a.barnes@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This set of changes introduces an atomic API to the PWM subsystem. This
is influenced by the DRM atomic API that was introduced a while back,
though it is obviously a lot simpler. The fundamental idea remains the
same, though: drivers provide a single callback to implement the atomic
configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware. Many
use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are postponed
to v4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sxT9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS
ioctl needs to be treated with special care, as it has the pointer
size encoded in the command.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a basic driver for the Surface 3. I am not so sure it will work
with any firmwares as most values are encoded, but given that I only have
access to my current device with its firmware and I don't have the
datasheet, it should be OK for now.
The Surface Pen is not supported (if it is supposed to be). I'll work on
this when I get one.
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 4369c64c79 ("Input: Send events one packet at a time")
significantly reduced amount of entropy input core was feeding to the rest
of the system, because only the very first event in the event block would
be used as source of entropy.
With this change we will be calling add_input_randomness() for every event
that is not filtered by the input core as a duplicate. In addition, all
EV_SYN events are ignored.
Acked-by: Henrik Rydberg <rydberg@bitmath.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The migor touchscreen driver is now available for COMPILE_TEST,
so we run into a harmless randconfig warning on ARM when CONFIG_PM
is disabled:
drivers/input/touchscreen/migor_ts.c:216:12: error: 'migor_ts_resume' defined but not used [-Werror=unused-function]
drivers/input/touchscreen/migor_ts.c:205:12: error: 'migor_ts_suspend' defined but not used [-Werror=unused-function]
This shuts up the warning by marking the two functions as __maybe_unused.
We could do the same thing by adding an #ifdef, but this version is
more reliable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The newly added Atmal captouch driver fails to build when CONFIG_I2C
is disabled:
drivers/input/misc/atmel_captouch.c: In function 'atmel_read':
drivers/input/misc/atmel_captouch.c:115:8: error: implicit declaration of function 'i2c_transfer' [-Werror=implicit-function-declaration]
This adds an explicit Kconfig dependency to prevent the broken
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b06d43f7a3 ("Input: add Atmel Captouch Button driver")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver only has runtime but no build time dependency with SH_MIGOR, so
it can be built for testing purposes if the COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that drivers are
not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is a typo in the driver for the I2C device table that is passed to
the MODULE_DEVICE_TABLE() macro, this leads to the following build error:
CC [M] drivers/input/touchscreen//migor_ts.o
drivers/input/touchscreen//migor_ts.c:233:21: error: 'migor_ts' undeclared here (not in a function)
MODULE_DEVICE_TABLE(i2c, migor_ts);
^
drivers/input/touchscreen//migor_ts.c:233:31: error: '__mod_i2c__migor_ts_device_table' aliased to undefined symbol 'migor_ts'
MODULE_DEVICE_TABLE(i2c, migor_ts);
^
scripts/Makefile.build:295: recipe for target 'drivers/input/touchscreen//migor_ts.o' failed
make[1]: *** [drivers/input/touchscreen//migor_ts.o] Error 1
Makefile:1446: recipe for target '_module_drivers/input/touchscreen/' failed
make: *** [_module_drivers/input/touchscreen/] Error 2
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Nick Dyer