The rawnand clock gate gates two clocks, NAND_USDHC_BUS_CLK_ROOT
and NAND_CLK_ROOT. However, the gate has been in the chain of the
latter only. This does not allow to use the NAND_USDHC_BUS_CLK_ROOT
only, e.g. as required by APBH-Bridge-DMA.
Add new clocks which represent the clock after the gate, and use a
shared clock gate to correctly model the hardware.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Commit ad14972422 ("clk: imx7d: Fix the powerdown bit location
of PLL DDR") used the incorrect bit for the IMX_PLLV3_DDR_IMX7 case.
Fix it accordingly to avoid a kernel hang.
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
According to the MX7D Reference Manual the powerdown bit of
CCM_ANALOG_PLL_DDRn register is bit 20, so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The USDHC NAND root clock is not gated by any CCM clock gate. Remove
the bogus gate definition.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the missing ipg_root_clk which actually is already used by many
orphan clks in current tree.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
MX7D ahb clk actually has no LPCG gate, current LPCG offset 0x4200
used actually is for adc, not ahb. After fix, correct ocram_s_clk
parent accordingly as well.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The clock was mapped on CG15 (gpio2_clocks) in the CCRG0 register.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Add the OCOTP so that this hardware block can be used.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The LDB mux/gate layout has been fixed on QuadPlus, so there is no need
to restrict the LDB mux changes on this hardware, as the erratum
preventing this from working properly is gone.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On vf610, PLL1 and PLL2 have registers to configure fractional part of
frequency multiplier.
This patch adds support for these registers.
This fixes "fast system clock" issue on boards where bootloader sets
fractional multiplier for PLL1.
Suggested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
CC: Chris Healy <cphealy@gmail.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of
the machines that are still normally used with classic board files.
One tegra fix is important for new bootloader versions, but the
bug has been around for a while without anyone noticing.
The other changes are mostly cosmetic.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i2l2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of the
machines that are still normally used with classic board files. One
tegra fix is important for new bootloader versions, but the bug has
been around for a while without anyone noticing.
The other changes are mostly cosmetic"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: tegra: Add missing Smaug revision
arm64: tegra: Add VDD_GPU regulator to Jetson TX1
arm64: dts: zte: clean up gic-v3 redistributor properties
arm64: dts: zx: Fix gic GICR property
bus: vexpress-config: fix device reference leak
soc: ti: qmss: fix the case when !SMP
ARM: lpc32xx: drop duplicate header device.h
ARM: ixp4xx: drop duplicate header gpio.h
ARM: socfpga: fix spelling mistake in error message
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
ARM: OMAP2+: Remove the omapdss_early_init_of() function
mfd: tps65217: Fix mismatched interrupt number
ARM: zx: Fix error handling
ARM: spear: Fix error handling
ARM: davinci: da850: Fix pwm name matching
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
...
- A patch series to fix the long standing issue with glitchy parent
mux of ldb_di_clk, which can hang up LVDS display when ipu_di_clk
is sourced from ldb_di_clk.
- A patch to add imx6ull clock support on top of imx6ul clock driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYKni2AAoJEFBXWFqHsHzOu+UIAKpiVKqacJYxD1wEJDh9Mtq2
o9U10aGY6yl3ZEa5Ik8OTqg2Aa6ZT5kaV8h9i5uv7XIGqCSM6SUcWweF0KlRyJP4
7bjz9rcir2/zXys+dVuRodUiF8uowoFxgw7wAHwHfzs1oA7ihQaUB4v6vBiNbADq
zheCn2AqDWhIKAOFkLcyEid2IyIz0S/tlyzfElBmukSons+0zTrJ+e9QePzcuRZO
TnhZAxc/FQwcPZ/a2kiwiOOfQXWQld5pIeIp1YHWD4+L4m0Yxb/WK1yaocTxox2O
Ek8BPlkpNYdic8g3DRlwZGCHe5UaESSEQ3pyXlgYAdIOA2i+0tlnnCVCW0gNvQc=
=DJo7
-----END PGP SIGNATURE-----
Merge tag 'imx-clk-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-next
Pull i.MX clock updates from Shawn Guo:
- A patch series to fix the long standing issue with glitchy parent
mux of ldb_di_clk, which can hang up LVDS display when ipu_di_clk
is sourced from ldb_di_clk.
- A patch to add imx6ull clock support on top of imx6ul clock driver.
* tag 'imx-clk-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx: clk-imx6ul: add clk support for imx6ull
clk: imx6: Fix procedure to switch the parent of LDB_DI_CLK
clk: imx6: Make the LDB_DI0 and LDB_DI1 clocks read-only
clk: imx6: Mask mmdc_ch1 handshake for periph2_sel and mmdc_ch1_axi_podf
imx6ull is the derived SoC from imx6ul
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The audio and video PLLs are designed to have a precision of 1 Hz if some
conditions are met. The current implementation only allows a precision that
depends on the rate of the parent clock. E.g., if the parent clock is 24
MHz, the precision will be 24 Hz; or more generally the precision will be
p / 10^6 Hz
where p is the parent clock rate. This comes down to how the register
values for the PLL's fractional loop divider are chosen.
The clock rate calculation for the PLL is
PLL output frequency = Fref * (DIV_SELECT + NUM / DENOM)
or with a shorter notation
r = p * (d + a / b)
In addition to all variables being integers, we also have the following
conditions:
27 <= d <= 54
-2^29 <= a <= 2^29-1
0 < b <= 2^30-1
|a| < b
Here, d, a and b are register values for the fractional loop divider. We
want to chose d, a and b such that f(p, r) = p, i.e. f is our round_rate
function. Currently, d and b are chosen as
d = r / p
b = 10^6
hence we get the poor precision. And a is defined in terms of r, d, p and
b:
a = (r - d * p) * b / p
I propose that if p <= 2^30-1 (i.e., the max value for b), we chose b as
b = p
We can do this since
|a| < b
|(r - d * p) * b / p| < b
|r - d * p| < p
Which have two solutions, one of them is when p < 0, so we can skip that
one. The other is when p > 0 and
p * (d - 1) < r < p * (d + 1)
Substitute d = r / p:
(r - p) < r < (r + p) <=> p > 0
So, as long as p > 0, we can chose b = p. This is a good choise for b since
a = (r - d * p) * b / p
= (r - d * p) * p / p
= r - d * p
r = p * (d + a / b)
= p * d + p * a / b
= p * d + p * a / p
= p * d + a
and if d = r / p:
a = r - d * p
= r - r / p * p
= 0
r = p * d + a
= p * d + 0
= p * r / p
= r
I reckon this is the intention by the design of the clock rate formula.
Signed-off-by: Emil Lundmark <emil@limesaudio.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since 'parent_rate * mfn' may overflow 32 bits, the result should be
stored using 64 bits.
The problem was discovered when trying to set the rate of the audio PLL
(pll4_post_div) on an i.MX6Q. The desired rate was 196.608 MHz, but
the actual rate returned was 192.000570 MHz. The round rate function should
have been able to return 196.608 MHz, i.e., the desired rate.
Fixes: ba7f4f557e ("clk: imx: correct AV PLL rate formula")
Cc: Anson Huang <b20788@freescale.com>
Signed-off-by: Emil Lundmark <emil@limesaudio.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Due to incorrect placement of the clock gate cell in the ldb_di[x]_clk
tree, the glitchy parent mux of ldb_di[x]_clk can cause a glitch to
enter the ldb_di_ipu_div divider. If the divider gets locked up, no
ldb_di[x]_clk is generated, and the LVDS display will hang when the
ipu_di_clk is sourced from ldb_di_clk.
To fix the problem, both the new and current parent of the ldb_di_clk
should be disabled before the switch. This patch ensures that correct
steps are followed when ldb_di_clk parent is switched in the beginning
of boot. The glitchy muxes are then registered as read-only. The clock
parent can be selected using the assigned-clocks and
assigned-clock-parents properties of the ccm device tree node:
&clks {
assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
<&clks IMX6QDL_CLK_LDB_DI1_SEL>;
assigned-clock-parents = <&clks IMX6QDL_CLK_MMDC_CH1_AXI>,
<&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
};
The issue is explained in detail in EB821 ("LDB Clock Switch Procedure &
i.MX6 Asynchronous Clock Switching Guidelines") [1].
[1] http://www.nxp.com/files/32bit/doc/eng_bulletin/EB821.pdf
Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Akshay Bhat <akshay.bhat@timesys.com>
Tested-by Joshua Clayton <stillcompiling@gmail.com>
Tested-by: Charles Kang <Charles.Kang@advantech.com.tw>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Due to incorrect placement of the clock gate cell in the ldb_di[x]_clk
tree, the glitchy parent mux of ldb_di[x]_clk can cause a glitch to
enter the ldb_di_ipu_div divider. If the divider gets locked up, no
ldb_di[x]_clk is generated, and the LVDS display will hang when the
ipu_di_clk is sourced from ldb_di_clk.
To fix the problem, both the new and current parent of the ldb_di_clk
should be disabled before the switch. As this can not be guaranteed by
the clock framework during runtime, make the ldb_di[x]_sel muxes read-only.
A workaround to set the muxes once during boot could be added to the
kernel or bootloader.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
MMDC CH1 is not used on i.MX6Q, so the handshake needed to change the
parent of periph2_sel or the divider of mmdc_ch1_axi_podf will never
succeed.
Disable the handshake mechanism to allow changing the frequency of
mmdc_ch1_axi, allowing to use it as a possible source for the LDB DI
clock.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Clock initialization for i.MX31 powered machines with DT support
should be done by a call of an init function registered with
CLK_OF_DECLARE() in common clock framework.
The change converts exported mx31_clocks_init_dt() into a static
initialization function registered by CLK_OF_DECLARE().
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Function mx31_clocks_init() is called during clock intialization on
legacy boards with reference clock frequency passed as its input
argument, this can be verified by examination of the function
declaration found in arch/arm/mach-imx/common.h and actual function
users which include that header file.
Inside CCF driver the function ignores its input argument, by chance
the used value in the function body is the same as input arguments on
side of all callers.
Fixes: d9388c8432 ("clk: imx31: Do not call mxc_timer_init twice when booting with DT")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion
of old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files.
If no regressions are found, another large cleanup for the platform
will happen as a follow-up, removing dead code and restructuring
the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now DT-only.
The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT
in principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress.
We can probably merge the remaining code into a single directory
in the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then.
Conflicts: two files deleted here have been modified upstream,
the changes can be discarded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAV/guBGCrR//JCVInAQJoaQ/+N42zjmqDg6zO2JSs3q793AHskllT7kJo
2G36Afl3hOZqy2TFF8nq5Iv8/hb45+3bHBIlq+JrOq5Fep3wFVfT0d1HMQ8UG6+K
jSMikItIZkOJdmjuZLEBzhjUFIEIpIrSuSY1Pej5Sy8zDzxT+n68gVqcm/qxa2w6
gPThdL69/XDo7JkF9TbYn0nrECey3ps9XnikNITWyQTrvCmlDVtGp6B+Cwi4cyvh
FfJ690GAJU3/9op+xLomtEt1sli/+xJUdpH0IktfuNrc/2i96NsiUgPbqprIP6C6
rGRN40tDClYa1viRexZlZdkCd7nH9PC+VCC59FONYiY8WmpwtNPVZ8px4D/rv7AX
GHDnqeVbzUK/CMxRsQC0bnvQnD/oDqkSkDD7ixzfUh2TQiJASXvuj1vOej5k06Vc
KFkpjh1dSZkehkUp106F2Obm8Sh7nNoG2olzrlzlza97OuYxAEBungIn95vjYbUj
IRrTQdKgv3gVVGXzHjH7TMr46MZLk6K4mHjDeuQr/NN8JyPH0uLTy6pjsdXRWCvO
sIWVhyMohKMU2q5NeBWmY0OtDje93JchRVeKfRaQ3+YysPMUTBK5ZtI5GB9tsM14
7/GA7MO4FA0MZWW2E/GllQzgreaokUzTxBbhANzcEyjGh9OEx4gYaSF68PRy/HBa
TlhH1PR3PNg=
=WaLy
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion of
old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files. If no regressions are found, another
large cleanup for the platform will happen as a follow-up, removing
dead code and restructuring the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now
DT-only. The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT in
principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress. We
can probably merge the remaining code into a single directory in
the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: select PCI_DOMAINS config from ARCH_MULTIPLATFORM
ARM: stop *MIGHT_HAVE_PCI* config from being selected redundantly
ARM: imx: (trivial) fix typo and grammar
ARM: clps711x: remove extraneous files
ARM: imx: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP2+: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP1: use IS_ENABLED() instead of checking for built-in or module
ARM: imx: remove platform-mxc_rnga
ARM: realview: imply device tree boot
ARM: realview: no need to select SMP_ON_UP explicitly
ARM: realview: delete the RealView board files
ARM: imx: no need to select SMP_ON_UP explicitly
ARM: i.MX: Move SOC_IMX1 into 'Device tree only'
ARM: i.MX: Remove i.MX1 non-DT support
ARM: i.MX: Remove i.MX1 Synertronixx SCB9328 board support
ARM: i.MX: Remove i.MX1 Armadeus APF9328 board support
ARM: mxs: remove obsolete startup code for TX28
ARM: i.MX31 iomux: remove duplicates with alternate name
ARM: i.MX31 iomux: remove plain duplicates
ARM: OMAP2+: Drop legacy board file for LDP
...
Initialize the GPU clock muxes to sane inputs. Until now they have
not been changed from their default values, which means that both
GPU3D shader and GPU2D core were fed by clock inputs whose rates
exceed the maximium allowed frequency of the cores by as much as
200MHz.
This fixes a severe GPU stability issue on i.MX6DL.
Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current clock tree only implements the minimal set of differences
between the i.MX6Q and the i.MX6DL, but that doesn't really reflect
reality.
Apply the following fixes to match the RM:
- DL has no GPU3D_SHADER_SEL/PODF, the shader domain is clocked by
GPU3D_CORE
- GPU3D_SHADER_SEL/PODF has been repurposed as GPU2D_CORE_SEL/PODF
- GPU2D_CORE_SEL/PODF has been repurposed as MLB_SEL/PODF
Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This fixes
[ 0.000000] i.MX clk 82: register failed with -17
because the name is duplicated.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 3713e3f5e9 ("clk: imx35: define two clocks for rtc")
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently we see the following error when using the SAI audio
driver on mx7:
Division by zero in kernel.
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.8.0-rc3-next-20160823
Hardware name: Freescale i.MX7 Dual (Device Tree)
Backtrace:
[<c010b70c>] (dump_backtrace) from [<c010b8a8>] (show_stack+0x18)
r6:60000013 r5:ffffffff r4:00000000 r3:00000000
[<c010b890>] (show_stack) from [<c03e9324>] (dump_stack+0xb0/0xe)
[<c03e9274>] (dump_stack) from [<c010b578>] (__div0+0x18/0x20)
r8:00000000 r7:ffffffff r6:ffffffff r5:00000000 r4:00000000 r3:0
[<c010b560>] (__div0) from [<c03e795c>] (Ldiv0_64+0x8/0x18)
[<c06cd860>] (divider_get_val) from [<c06cda28>] (clk_divider_se)
This error happens due to the lack of definition of the
IMX7D_PLL_AUDIO_TEST_DIV/IMX7D_PLL_AUDIO_POST_DIV clocks.
Add support for them.
Tested on a imx7s-warp board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The SAI_IPG clocks are enabled by the same bits that control SAI_ROOT_CLK
clocks, so represent them as shared clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Introduce imx_clk_gate2_shared2() which is similar to the existing
imx_clk_gate2_shared() and passes CLK_OPS_PARENT_ENABLE flag, which
is useful for i.MX7 shared clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add IMX7D_SDMA_CORE_CLK clock so that SDMA can be functional.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Booting the kernel on a imx7s-warp leads to several warnings like these:
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/locking/lockdep.c:3536 lock_release+0x2f8/0x330
[ 0.000000] releasing a pinned lock
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/locking/lockdep.c:2722 trace_hardirqs_on_caller+0x1ac/0x1f4
[ 0.000000] DEBUG_LOCKS_WARN_ON(unlikely(early_boot_irqs_disabled))
[ 0.000000] ---[ end trace cb88537fdc8fa201 ]---
[ 0.000000] bad: scheduling from the idle thread!
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.7.0-rc7-next-20160715 #404
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/time/sched_clock.c:179 sched_clock_register+0x44/0x1f8
[ 0.000000] Modules linked in:
[ 0.000591] ------------[ cut here ]------------
[ 0.000610] WARNING: CPU: 0 PID: 0 at kernel/time/sched_clock.c:179 sched_clock_register+0x44/0x1f8
[ 0.002084] ------------[ cut here ]------------
[ 0.002104] WARNING: CPU: 0 PID: 0 at init/main.c:576 start_kernel+0x258/0x3b0
[ 0.002114] Interrupts were enabled early
This fix is along the same lines as 5e33ebff7e ("clk: imx7d: do not
set parent of ethernet time/ref clocks") and the explanation from that
commit is:
"The reason for the warning is that setting the parent enables the ENET
PLL since we are using CLK_OPS_PARENT_ENABLE. Enabling the ENET PLL can
cause clk_pllv3_wait_lock to sleep. See also:
commit fc8726a2c0 ("clk: core: support clocks which requires parents
enable (part 2)")."
imx7s-warp does not even use the FEC interface, so we should not really
configure the parent of IMX7D_ENET_AXI_ROOT_SRC in the common MX7 clock
driver code.
The dts file should use the assigned-clocks/assigned-clock-parents method,
so simply remove the configuration of IMX7D_ENET_AXI_ROOT_SRC parent.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch removes registration helpers and support files,
used for non-DT i.MX1 targets.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All device trees currently in mainline specify the time clock parent
using the assigned-clocks/assigned-clock-parents method, there is no
need to statically assign the parent in the core clock driver.
Also all current boards provide an Ethernet reference clock for the
PHY externally, hence configuring the internal PHY reference clock.
Furthermore, and the actual driver of this patch, specify ethernet
related parents at that early point in boot leads to a warning:
bad: scheduling from the idle thread!
The reason for the warning is that setting the parent enables the ENET
PLL since we are using CLK_OPS_PARENT_ENABLE. Enabling the ENET PLL can
cause clk_pllv3_wait_lock to sleep. See also:
commit fc8726a2c0 ("clk: core: support clocks which requires parents
enable (part 2)").
Note that setting the ENET AXI root clock parent also requires ENET
PLL to be enabled. However, U-Boot typically leaves the ENET PLL on,
hence when the framework sets the parent of the first clock, it does
not need to wait for the PLL to come up. But because there is currently
no user of that clock, the PLL gets disabled after setting the parent.
Therefore, subsequent reparenting calls of any clock which somehow rely
on the ENET PLL, need to reenable the ENET PLL which leads to a sleep.
Removing those subsequent reparenting calls works around this issue.
Also remove comments. The code is really verbose enough.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160703174813.13970-1-stefan@agner.ch
In order to allow wake support in STOP sleep mode, clocks are needed. Use
imx_clk_gate2_cgr to disable automatic clock gating in low power mode STOP.
This allows to enable wake by UART using:
echo enabled > /sys/class/tty/ttyLP0/power/wakeup
However, if wake is not enabled, the driver should disable the clocks explicitly
to save power.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160628053235.5114-3-bhuvanchandra.dv@toradex.com
Formerly clk core does not support imx7d clock type well that all
its clock operations requires the parent clock on.
Therefore we enabled all clocks by default in clock driver
initialization for other module clocks operate well.
After patch 'clk: imx7d: using api with flag CLK_OPS_PARENT_ENABLE',
clk core can handle such clock type well, so we don't have to enable
them all by default anymore. Instead, we only enable a minimum required
set of clocks.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
i.MX7D requires all clocks operations including enable/disable,
rate change and re-parent with its parent clock on.
Changing to the correct APIs to tell clk core such requirement.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
IMX SoCs like i.MX7D requires using CLK_OPS_PARENT_ENABLE flags,
adding the corresponding clock APIs variants for easily to use.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Re-order and concentrate the same type of clk api for better
code maintenance.
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The powerdown bit is a bit confused, let's change it to power_bit
to relfect both powerdown and powerup case according to different
plls.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After commit f53947456f ("ARM: clk: imx: update pllv3 to support imx7"),
the former used BM_PLL_POWER bit is not correct anymore for IMX7 ENET.
Instead, pll->powerdown holds the correct bit, so using powerdown bit
in clk_pllv3_{prepare | unprepare} functions.
Fixes: f53947456f ("ARM: clk: imx: update pllv3 to support imx7")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pllx_bypass_src mux shouldn't be the parent of pllx clock
since it's only valid when when pllx BYPASS bit is set.
Thus it is actually one parent of pllx_bypass only.
Instead, pllx parent should be fixed to osc according to
reference manual.
Other plls have the same issue.
e.g. before fix, the pll tree is:
osc 6 6 24000000 0 0
pll1_bypass_src 0 0 24000000 0 0
pll1 0 0 792000000 0 0
pll1_bypass 0 0 792000000 0 0
pll1_sys 0 0 792000000 0 0
After the fix, it's:
osc 6 6 24000000 0 0
pll1 0 0 792000000 0 0
pll1_bypass 0 0 792000000 0 0
pll1_sys 0 0 792000000 0 0
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DRAM PLL is a audio/video type PLL, need to correct
it to get correct ops of PLL.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DRAM root clk should be either from pll dram main clk
or dram alt root clk.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The audio/video PLL's rate calculation is as below in RM:
Fref * (DIV_SELECT + NUM / DENOM), in origin clk-pllv3's
code, below code is used:
(parent_rate * div) + ((parent_rate / mfd) * mfn
as it does NOT consider the float data using div, so below
formula should be used as a decent method:
(parent_rate * div) + ((parent_rate * mfn) / mfd)
and we also need to consider parent_rate * mfd may overflow
a 32 bit value, 64 bit value should be used.
After updating this formula, the dram PLL's rate is
1066MHz, which is correct, while the old formula gets
1056MHz.
[Aisheng: fix clk_pllv3_av_round_rate too]
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull some non-critical i.MX clk fixes from Shawn Guo:
* Fix the commit 3713e3f5e9 ("clk: imx35: define two clocks for rtc")
which messed up the clock enumeration when adding new clock.
* tag 'imx-clk-fixes-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx35: restore existing used clock enumeration
clk: imx6q: fix typo in CAN clock definition
The clock parent of the AHB root clock when using mux option 1
is the SYS PLL 270MHz clock. This is specified in Table 5-11
Clock Root Table of the i.MX 7Dual Applications Processor
Reference Manual.
While it could be a documentation error, the 270MHz parent is
also mentioned in the boot ROM configuration in Table 6-28: The
clock is by default at 135MHz due to a POST_PODF value of 1
(=> divider of 2).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7 designs Ethernet PLL provides a 1000MHz reference clock.
Store the reference clock in the clk_pllv3 structure according to
the PLL type.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner