Fix whitespace, capitalization, and spelling errors. No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.
Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PCIe PME doesn't depend on ACPI, so remove the #includes and
Kconfig dependency.
Based-on-patch-by: Andrew Murray <Andrew.Murray@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce an inline function pci_pcie_type(dev) to extract PCIe
device type from pci_dev->pcie_flags_reg field, and prepare for
removing pci_dev->pcie_type.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The land of PCI power management is a land of sorrow and ugliness,
especially in the area of signaling events by devices. There are
devices that set their PME Status bits, but don't really bother
to send a PME message or assert PME#. There are hardware vendors
who don't connect PME# lines to the system core logic (they know
who they are). There are PCI Express Root Ports that don't bother
to trigger interrupts when they receive PME messages from the devices
below. There are ACPI BIOSes that forget to provide _PRW methods for
devices capable of signaling wakeup. Finally, there are BIOSes that
do provide _PRW methods for such devices, but then don't bother to
call Notify() for those devices from the corresponding _Lxx/_Exx
GPE-handling methods. In all of these cases the kernel doesn't have
a chance to receive a proper notification that it should wake up a
device, so devices stay in low-power states forever. Worse yet, in
some cases they continuously send PME Messages that are silently
ignored, because the kernel simply doesn't know that it should clear
the device's PME Status bit.
This problem was first observed for "parallel" (non-Express) PCI
devices on add-on cards and Matthew Garrett addressed it by adding
code that polls PME Status bits of such devices, if they are enabled
to signal PME, to the kernel. Recently, however, it has turned out
that PCI Express devices are also affected by this issue and that it
is not limited to add-on devices, so it seems necessary to extend
the PME polling to all PCI devices, including PCI Express and planar
ones. Still, it would be wasteful to poll the PME Status bits of
devices that are known to receive proper PME notifications, so make
the kernel (1) poll the PME Status bits of all PCI and PCIe devices
enabled to signal PME and (2) disable the PME Status polling for
devices for which correct PME notifications are received.
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make wakeup events be reported by the PCI subsystem before attempting to
resume devices or queuing up runtime resume requests for them, because
wakeup events should be reported as soon as they have been detected.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I noticed that PCI Express PMEs don't work on my Toshiba Portege R500
after the system has been woken up from a sleep state by a PME
(through Wake-on-LAN). After some investigation it turned out that
the BIOS didn't clear the Root PME Status bit in the root port that
received the wakeup PME and since the Requester ID was also set in
the port's Root Status register, any subsequent PMEs didn't trigger
interrupts.
This problem can be avoided by clearing the Root PME Status bits in
all PCI Express root ports during early resume. For this purpose,
add an early resume routine to the PCIe port driver and make this
driver be always registered, even if pci_ports_disable is set (in
which case the driver's only function is to provide the early
resume callback).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCIe PME code only consists of one file, so it doesn't need to
occupy its own directory. Move it to drivers/pci/pcie/pme.c and
remove the contents of drivers/pci/pcie/pme .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bjorn Helgaas