The register offsets have been changed in SD8897 and newer chips.
Define a new btmrvl_sdio_card_reg map for SD88xx.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the initial skeleton for Three-wire UART (H5) support
and hooks it up to the HCI UART framework.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The SD8797 firmware image is shared with mwifiex driver.
Whoever gets loaded first will be responsible for firmware
downloading.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The SD8787 firmware image is shared with mwifiex driver.
Whoever gets loaded first will be responsible for firmware
downloading.
Signed-off-by: Kevin Gan <ganhy@marvell.com>
Signed-off-by: Tristan Xu <xurf@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This is the bluetooth protocol driver for the TI WiLink7 chipsets.
Texas Instrument's WiLink chipsets combine wireless technologies
like BT, FM, GPS and WLAN onto a single chip.
This Bluetooth driver works on top of the TI_ST shared transport
line discipline driver which also allows other drivers like
FM V4L2 and GPS character driver to make use of the same UART interface.
Kconfig and Makefile modifications to enable the Bluetooth
driver for Texas Instrument's WiLink 7 chipset.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implements Atheros AR300x serial HCI protocol.
This protocol extends H4 serial protocol to implement enhanced power
management features supported by Atheros AR300x serial Bluetooth chipsets.
Signed-off-by: Suraj Sumangala <suraj@atheros.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Marvell driver selects DEBUG_FS and FW_LOADER for its core driver
and that is pointless. Don't select DEBUG_FS since it is either enabled
or not and it is not for the driver to enable it. Also FW_LOADER is
only used within the SDIO driver and so just have that one select the
FW_LOADER option.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
/debug/btmrvl/config/
/debug/btmrvl/status/
See Documentation/btmrvl.txt for details.
This patch incorporates a lot of comments given by
Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre.
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This driver supports Marvell Bluetooth enabled devices with SDIO
interface. Currently only SD8688 chip is supported.
The helper/firmware images of SD8688 can be downloaded from this tree:
git://git.infradead.org/users/dwmw2/linux-firmware.git
This patch incorporates a lot of comments given by
Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre.
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This driver provides basic definitions and library functions to
support Marvell Bluetooth enabled devices, such as 88W8688 WLAN/BT
combo chip.
This patch incorporates a lot of comments given by
Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre.
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The old hci_usb driver has been fully replaced with the new btusb driver
and all major distributions switched to the new driver now. This removes
it since it should not be used at all anymore.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new generic driver for Bluetooth USB devices was missing proper
SCO support. The driver now claims the second interface for these USB
devices to allow the flow of SCO packets. It also handles switching
of the alternate setting and re-submission of isochronous URBs.
The btusb driver is now a full replacement for hci_usb and thus the
experimental tag has been removed and this driver is promoted as
preferred one.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix bluetooth hci_bcsp Kconfig to avoid build errors:
drivers/built-in.o: In function `bcsp_prepare_pkt':
hci_bcsp.c:(.text+0x7e9ac): undefined reference to `bitrev16'
drivers/built-in.o: In function `bcsp_recv':
hci_bcsp.c:(.text+0x7f276): undefined reference to `bitrev16'
hci_bcsp.c:(.text+0x7f293): undefined reference to `bitrev16'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Ackey-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bitrev16 from lib/bitrev.c.
Use the get_unaligned_be16 to get the crc from the packet, create a
small helper function for this.
Fix a shadowed variable sparse warning:
drivers/bluetooth/hci_bcsp.c:218:26: warning: symbol 'hdr' shadows an earlier one
drivers/bluetooth/hci_bcsp.c:187:5: originally declared here
[akpm@linux-foundation.org: select CONFIG_BITREVERSE, noted by akinobu.mita@gmail.com]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new generic driver for Bluetooth USB devices. This
driver is still experimental at this point, but it is cleaner and
easier to maintain than the current Bluetooth USB driver. It is a
much better starting point for power management improvements.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a generic driver for Bluetooth SDIO devices. It
supports Type-A and Type-B devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support for Texas Instruments' HCI Low Level (HCILL) Bluetooth
protocol, which is a power management extension to H4. The HCILL is
widely used by TI's BRF63xx Bluetooth chips.
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Stephan Gabert