USB4 spec specifies standard access to retimers (both on-board and
cable) through USB4 port sideband access. This makes it possible to
upgrade their firmware in the same way than we already do with the
routers.
This enumerates on-board retimers under each USB4 port when the link
comes up and adds them to the bus under the router the retimer belongs
to. Retimers are exposed in sysfs with name like <device>:<port>.<index>
where device is the router the retimer belongs to, port is the USB4 port
the retimer is connected to and index is the retimer index under that
port (starting from 1). This applies to the upstream USB4 port as well
so if there is on-board retimer between the port and the router it is
also added accordingly.
At this time we do not add cable retimers but there is no techincal
restriction to do so in the future if needed. It is not clear whether it
makes sense to upgrade their firmwares and at least Thunderbolt 3 cables
it has not been done outside of lab environments.
The sysfs interface is made to follow the router NVM upgrade to make it
easy to extend the existing userspace (fwupd) to handle these as well.
Signed-off-by: Kranthi Kuntala <kranthi.kuntala@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fix heading format warnings in admin-guide/sysctl/kernel.rst:
Documentation/admin-guide/sysctl/kernel.rst:339: WARNING: Title underline too short.
hung_task_all_cpu_backtrace:
================
Documentation/admin-guide/sysctl/kernel.rst:650: WARNING: Title underline too short.
oops_all_cpu_backtrace:
================
Fixes: 0ec9dc9bcb ("kernel/hung_task.c: introduce sysctl to print all traces when a hung task is detected")
Fixes: 60c958d8df ("panic: add sysctl to dump all CPUs backtraces on oops event")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/8af1cb77-4b5a-64b9-da5d-f6a95e537f99@infradead.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The lengths of underlines must match the titles to avoid build warnings.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Mark Gross<mgross@linux.intel.com>
Link: https://lore.kernel.org/r/20200615203645.11545-1-xypron.glpk@gmx.de
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Document the efi=novamap kernel command line parameter.
Put the efi parameters into alphabetic order.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Link: https://lore.kernel.org/r/20200616104012.4780-1-xypron.glpk@gmx.de
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Solves this Sphinx warning:
Documentation/admin-guide/device-mapper/dm-ebs.rst: WARNING: document isn't included in any toctree
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This is temporary. It will allow the next few patches to be tested
incrementally.
Setting unsafe_fsgsbase is a root hole. Don't do it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Link: https://lkml.kernel.org/r/1557309753-24073-4-git-send-email-chang.seok.bae@intel.com
Link: https://lkml.kernel.org/r/20200528201402.1708239-3-sashal@kernel.org
HTTP links to HTTPS that had to be yanked and redone before the first
pull.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl7hRs0PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YEE0H/jlTBzV3kkf09nzngka07kUlXTsd5kkQjXNr
sr0zV4q7o70Hc9mv8r5m5suBFuQ+2rx9Oy2BB4ywOAFIXMkhycCzj/v+tkBLav2s
+oJ6ytSAnFIoyfChq+ynX2ub0VEE86zxafGaL1xt0SwRt/hSAQWXmfN3m8DorqF3
bXn2WzKhBxPhjxrRUhzgQVyXnEUbONshFzng7E0OtKMbOw7ftEdh18JdZ2M/KQwH
DPD+wtmzns/uUUarkC/fmaj8JLD1Bq5X9VTpkz0YU151GX1P4mbMZcWSA8/QHnoS
B21LMa58itBsQxchN7LvdnkbDj3GIUzDiXsLt9VXMOd+TK4TyhE=
=mp4N
-----END PGP SIGNATURE-----
Merge tag 'docs-5.8-2' of git://git.lwn.net/linux
Pull more documentation updates from Jonathan Corbet:
"A handful of late-arriving docs fixes, along with a patch changing a
lot of HTTP links to HTTPS that had to be yanked and redone before the
first pull"
* tag 'docs-5.8-2' of git://git.lwn.net/linux:
docs/memory-barriers.txt/kokr: smp_mb__{before,after}_atomic(): update Documentation
Documentation: devres: add missing entry for devm_platform_get_and_ioremap_resource()
Replace HTTP links with HTTPS ones: documentation
docs: it_IT: address invalid reference warnings
doc: zh_CN: use doc reference to resolve undefined label warning
docs: Update the location of the LF NDA program
docs: dev-tools: coccinelle: underlines
Merge even more updates from Andrew Morton:
- a kernel-wide sweep of show_stack()
- pagetable cleanups
- abstract out accesses to mmap_sem - prep for mmap_sem scalability work
- hch's user acess work
Subsystems affected by this patch series: debug, mm/pagemap, mm/maccess,
mm/documentation.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (93 commits)
include/linux/cache.h: expand documentation over __read_mostly
maccess: return -ERANGE when probe_kernel_read() fails
x86: use non-set_fs based maccess routines
maccess: allow architectures to provide kernel probing directly
maccess: move user access routines together
maccess: always use strict semantics for probe_kernel_read
maccess: remove strncpy_from_unsafe
tracing/kprobes: handle mixed kernel/userspace probes better
bpf: rework the compat kernel probe handling
bpf:bpf_seq_printf(): handle potentially unsafe format string better
bpf: handle the compat string in bpf_trace_copy_string better
bpf: factor out a bpf_trace_copy_string helper
maccess: unify the probe kernel arch hooks
maccess: remove probe_read_common and probe_write_common
maccess: rename strnlen_unsafe_user to strnlen_user_nofault
maccess: rename strncpy_from_unsafe_strict to strncpy_from_kernel_nofault
maccess: rename strncpy_from_unsafe_user to strncpy_from_user_nofault
maccess: update the top of file comment
maccess: clarify kerneldoc comments
maccess: remove duplicate kerneldoc comments
...
Pull x86 srbds fixes from Thomas Gleixner:
"The 9th episode of the dime novel "The performance killer" with the
subtitle "Slow Randomizing Boosts Denial of Service".
SRBDS is an MDS-like speculative side channel that can leak bits from
the random number generator (RNG) across cores and threads. New
microcode serializes the processor access during the execution of
RDRAND and RDSEED. This ensures that the shared buffer is overwritten
before it is released for reuse. This is equivalent to a full bus
lock, which means that many threads running the RNG instructions in
parallel have the same effect as the same amount of threads issuing a
locked instruction targeting an address which requires locking of two
cachelines at once.
The mitigation support comes with the usual pile of unpleasant
ingredients:
- command line options
- sysfs file
- microcode checks
- a list of vulnerable CPUs identified by model and stepping this
time which requires stepping match support for the cpu match logic.
- the inevitable slowdown of affected CPUs"
* branch 'x86/srbds' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation: Add Ivy Bridge to affected list
x86/speculation: Add SRBDS vulnerability and mitigation documentation
x86/speculation: Add Special Register Buffer Data Sampling (SRBDS) mitigation
x86/cpu: Add 'table' argument to cpu_matches()
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the
pdev->no_vf_scan flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio
and qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl7eVGcACgkQjYWKoQLX
FBhweQgAkicvx31x230rdfG+jQkQkl0UqF99vvWrJHEll77SqadfjzKAGIjUB+K0
EoeHVD5Wcj7BogDGcyHeQ0bZpu4WzE+y1nmnrsvu7TEEvcBmkJH0rF2jF+y0sb/O
3qvwFkX/CB5OqaMzKC/AEeRpcCKR+ZUXkWu1irbYth7CBXaycD9EAPc4cj8CfYGZ
r5njUdYOVk77TaO4aV+t5pCYc5TCRJaWXSsWaAv/nuLcIqsFBYOy2q+L47zITGXp
utZVanIDjzx+ikpaKicOIfC3hJsRuNX9MnlZKsQFwpVEZAUZmIUm29XdhGJTWSxU
RV7m1ORINbFP1nGAqWqkOvGo/LC0ZA==
=VhXR
-----END PGP SIGNATURE-----
Merge tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the pdev->no_vf_scan
flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio and
qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
* tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (52 commits)
vfio-ccw: make vfio_ccw_regops variables declarations static
vfio-ccw: Add trace for CRW event
vfio-ccw: Wire up the CRW irq and CRW region
vfio-ccw: Introduce a new CRW region
vfio-ccw: Refactor IRQ handlers
vfio-ccw: Introduce a new schib region
vfio-ccw: Refactor the unregister of the async regions
vfio-ccw: Register a chp_event callback for vfio-ccw
vfio-ccw: Introduce new helper functions to free/destroy regions
vfio-ccw: document possible errors
vfio-ccw: Enable transparent CCW IPL from DASD
s390/pci: Log new handle in clp_disable_fh()
s390/cio, s390/qeth: cleanup PNSO CHSC
s390/qdio: remove q->first_to_kick
s390/qdio: fix up qdio_start_irq() kerneldoc
s390: remove critical section cleanup from entry.S
s390: add machine check SIGP
s390/pci: ioremap() align with generic code
s390/ap: introduce new ap function ap_get_qdev()
Documentation/s390: Update / remove developerWorks web links
...
Starting from v4.19 commit 29ef680ae7 ("memcg, oom: move out_of_memory
back to the charge path") cgroup oom killer is no longer invoked only
from page faults. Now it implements the same semantics as global OOM
killer: allocation context invokes OOM killer and keeps retrying until
success.
[akpm@linux-foundation.org: fixes per Randy]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Link: http://lkml.kernel.org/r/158894738928.208854.5244393925922074518.stgit@buzz
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Usually when the kernel reaches an oops condition, it's a point of no
return; in case not enough debug information is available in the kernel
splat, one of the last resorts would be to collect a kernel crash dump
and analyze it. The problem with this approach is that in order to
collect the dump, a panic is required (to kexec-load the crash kernel).
When in an environment of multiple virtual machines, users may prefer to
try living with the oops, at least until being able to properly shutdown
their VMs / finish their important tasks.
This patch implements a way to collect a bit more debug details when an
oops event is reached, by printing all the CPUs backtraces through the
usage of NMIs (on architectures that support that). The sysctl added
(and documented) here was called "oops_all_cpu_backtrace", and when set
will (as the name suggests) dump all CPUs backtraces.
Far from ideal, this may be the last option though for users that for
some reason cannot panic on oops. Most of times oopses are clear enough
to indicate the kernel portion that must be investigated, but in virtual
environments it's possible to observe hypervisor/KVM issues that could
lead to oopses shown in other guests CPUs (like virtual APIC crashes).
This patch hence aims to help debug such complex issues without
resorting to kdump.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Matthew Wilcox <willy@infradead.org>
Link: http://lkml.kernel.org/r/20200327224116.21030-1-gpiccoli@canonical.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 401c636a0e ("kernel/hung_task.c: show all hung tasks before
panic") introduced a change in that we started to show all CPUs
backtraces when a hung task is detected _and_ the sysctl/kernel
parameter "hung_task_panic" is set. The idea is good, because usually
when observing deadlocks (that may lead to hung tasks), the culprit is
another task holding a lock and not necessarily the task detected as
hung.
The problem with this approach is that dumping backtraces is a slightly
expensive task, specially printing that on console (and specially in
many CPU machines, as servers commonly found nowadays). So, users that
plan to collect a kdump to investigate the hung tasks and narrow down
the deadlock definitely don't need the CPUs backtrace on dmesg/console,
which will delay the panic and pollute the log (crash tool would easily
grab all CPUs traces with 'bt -a' command).
Also, there's the reciprocal scenario: some users may be interested in
seeing the CPUs backtraces but not have the system panic when a hung
task is detected. The current approach hence is almost as embedding a
policy in the kernel, by forcing the CPUs backtraces' dump (only) on
hung_task_panic.
This patch decouples the panic event on hung task from the CPUs
backtraces dump, by creating (and documenting) a new sysctl called
"hung_task_all_cpu_backtrace", analog to the approach taken on soft/hard
lockups, that have both a panic and an "all_cpu_backtrace" sysctl to
allow individual control. The new mechanism for dumping the CPUs
backtraces on hung task detection respects "hung_task_warnings" by not
dumping the traces in case there's no warnings left.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: http://lkml.kernel.org/r/20200327223646.20779-1-gpiccoli@canonical.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After a recent change introduced by Vlastimil's series [0], kernel is
able now to handle sysctl parameters on kernel command line; also, the
series introduced a simple infrastructure to convert legacy boot
parameters (that duplicate sysctls) into sysctl aliases.
This patch converts the watchdog parameters softlockup_panic and
{hard,soft}lockup_all_cpu_backtrace to use the new alias infrastructure.
It fixes the documentation too, since the alias only accepts values 0 or
1, not the full range of integers.
We also took the opportunity here to improve the documentation of the
previously converted hung_task_panic (see the patch series [0]) and put
the alias table in alphabetical order.
[0] http://lkml.kernel.org/r/20200427180433.7029-1-vbabka@suse.cz
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Kees Cook <keescook@chromium.org>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Link: http://lkml.kernel.org/r/20200507214624.21911-1-gpiccoli@canonical.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can now handle sysctl parameters on kernel command line and have
infrastructure to convert legacy command line options that duplicate
sysctl to become a sysctl alias.
This patch converts the hung_task_panic parameter. Note that the sysctl
handler is more strict and allows only 0 and 1, while the legacy
parameter allowed any non-zero value. But there is little reason anyone
would not be using 1.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Guilherme G . Piccoli" <gpiccoli@canonical.com>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Ivan Teterevkov <ivan.teterevkov@nutanix.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20200427180433.7029-4-vbabka@suse.cz
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "support setting sysctl parameters from kernel command line", v3.
This series adds support for something that seems like many people
always wanted but nobody added it yet, so here's the ability to set
sysctl parameters via kernel command line options in the form of
sysctl.vm.something=1
The important part is Patch 1. The second, not so important part is an
attempt to clean up legacy one-off parameters that do the same thing as
a sysctl. I don't want to remove them completely for compatibility
reasons, but with generic sysctl support the idea is to remove the
one-off param handlers and treat the parameters as aliases for the
sysctl variants.
I have identified several parameters that mention sysctl counterparts in
Documentation/admin-guide/kernel-parameters.txt but there might be more.
The conversion also has varying level of success:
- numa_zonelist_order is converted in Patch 2 together with adding the
necessary infrastructure. It's easy as it doesn't really do anything
but warn on deprecated value these days.
- hung_task_panic is converted in Patch 3, but there's a downside that
now it only accepts 0 and 1, while previously it was any integer
value
- nmi_watchdog maps to two sysctls nmi_watchdog and hardlockup_panic,
so there's no straighforward conversion possible
- traceoff_on_warning is a flag without value and it would be required
to handle that somehow in the conversion infractructure, which seems
pointless for a single flag
This patch (of 5):
A recently proposed patch to add vm_swappiness command line parameter in
addition to existing sysctl [1] made me wonder why we don't have a
general support for passing sysctl parameters via command line.
Googling found only somebody else wondering the same [2], but I haven't
found any prior discussion with reasons why not to do this.
Settings the vm_swappiness issue aside (the underlying issue might be
solved in a different way), quick search of kernel-parameters.txt shows
there are already some that exist as both sysctl and kernel parameter -
hung_task_panic, nmi_watchdog, numa_zonelist_order, traceoff_on_warning.
A general mechanism would remove the need to add more of those one-offs
and might be handy in situations where configuration by e.g.
/etc/sysctl.d/ is impractical.
Hence, this patch adds a new parse_args() pass that looks for parameters
prefixed by 'sysctl.' and tries to interpret them as writes to the
corresponding sys/ files using an temporary in-kernel procfs mount.
This mechanism was suggested by Eric W. Biederman [3], as it handles
all dynamically registered sysctl tables, even though we don't handle
modular sysctls. Errors due to e.g. invalid parameter name or value
are reported in the kernel log.
The processing is hooked right before the init process is loaded, as
some handlers might be more complicated than simple setters and might
need some subsystems to be initialized. At the moment the init process
can be started and eventually execute a process writing to /proc/sys/
then it should be also fine to do that from the kernel.
Sysctls registered later on module load time are not set by this
mechanism - it's expected that in such scenarios, setting sysctl values
from userspace is practical enough.
[1] https://lore.kernel.org/r/BL0PR02MB560167492CA4094C91589930E9FC0@BL0PR02MB5601.namprd02.prod.outlook.com/
[2] https://unix.stackexchange.com/questions/558802/how-to-set-sysctl-using-kernel-command-line-parameter
[3] https://lore.kernel.org/r/87bloj2skm.fsf@x220.int.ebiederm.org/
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Ivan Teterevkov <ivan.teterevkov@nutanix.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: "Guilherme G . Piccoli" <gpiccoli@canonical.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Link: http://lkml.kernel.org/r/20200427180433.7029-1-vbabka@suse.cz
Link: http://lkml.kernel.org/r/20200427180433.7029-2-vbabka@suse.cz
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Analogously to the introduction of panic_on_warn, this patch introduces
a kernel option named panic_on_taint in order to provide a simple and
generic way to stop execution and catch a coredump when the kernel gets
tainted by any given flag.
This is useful for debugging sessions as it avoids having to rebuild the
kernel to explicitly add calls to panic() into the code sites that
introduce the taint flags of interest.
For instance, if one is interested in proceeding with a post-mortem
analysis at the point a given code path is hitting a bad page (i.e.
unaccount_page_cache_page(), or slab_bug()), a coredump can be collected
by rebooting the kernel with 'panic_on_taint=0x20' amended to the
command line.
Another, perhaps less frequent, use for this option would be as a means
for assuring a security policy case where only a subset of taints, or no
single taint (in paranoid mode), is allowed for the running system. The
optional switch 'nousertaint' is handy in this particular scenario, as
it will avoid userspace induced crashes by writes to sysctl interface
/proc/sys/kernel/tainted causing false positive hits for such policies.
[akpm@linux-foundation.org: tweak kernel-parameters.txt wording]
Suggested-by: Qian Cai <cai@lca.pw>
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Takashi Iwai <tiwai@suse.de>
Link: http://lkml.kernel.org/r/20200515175502.146720-1-aquini@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of enabling dynamic debug globally with CONFIG_DYNAMIC_DEBUG,
CONFIG_DYNAMIC_DEBUG_CORE will only enable core function of dynamic
debug. With the DYNAMIC_DEBUG_MODULE defined for any modules, dynamic
debug will be tied to them.
This is useful for people who only want to enable dynamic debug for
kernel modules without worrying about kernel image size and memory
consumption is increasing too much.
[orson.zhai@unisoc.com: v2]
Link: http://lkml.kernel.org/r/1587408228-10861-1-git-send-email-orson.unisoc@gmail.com
Signed-off-by: Orson Zhai <orson.zhai@unisoc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Petr Mladek <pmladek@suse.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Link: http://lkml.kernel.org/r/1586521984-5890-1-git-send-email-orson.unisoc@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200526060544.25127-1-grandmaster@al2klimov.de
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
Note, you will get a conflict merging with your tree in the
Documentation/devicetree/bindings/serial/rs485.yaml file, but it should
be pretty obvious what to do. If not, I'm sure Rob will clean it all up
afterwards :)
All of these have been in linux-next with no issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzpCg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRxACgjGtOKPjahONL4lWd0F8ZYEcyw7sAn34woBCO
BDUV3kolrRQ4OYNJWsHP
=TvqG
-----END PGP SIGNATURE-----
Merge tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
All of these have been in linux-next with no issues for a while"
* tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (67 commits)
tty: serial: qcom_geni_serial: Add 51.2MHz frequency support
tty: serial: imx: clear Ageing Timer Interrupt in handler
serial: 8250_fintek: Add F81966 Support
sc16is7xx: Add flag to activate IrDA mode
dt-bindings: sc16is7xx: Add flag to activate IrDA mode
serial: 8250: Support rs485 bus termination GPIO
serial: 8520_port: Fix function param documentation
dt-bindings: serial: Add binding for rs485 bus termination GPIO
vt: keyboard: avoid signed integer overflow in k_ascii
serial: 8250: Enable 16550A variants by default on non-x86
tty: hvc_console, fix crashes on parallel open/close
serial: imx: Initialize lock for non-registered console
sc16is7xx: Read the LSR register for basic device presence check
sc16is7xx: Allow sharing the IRQ line
sc16is7xx: Use threaded IRQ
sc16is7xx: Always use falling edge IRQ
tty: n_gsm: Fix bogus i++ in gsm_data_kick
tty: n_gsm: Remove unnecessary test in gsm_print_packet()
serial: stm32: add no_console_suspend support
tty: serial: fsl_lpuart: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
...
- allow only 'config', 'comment', 'if' statements inside 'choice' since
the other statements are not sensible inside 'choice' and should be
grammatical error
- support LMC_KEEP env variable for 'make local{yes,mod}config' to
preserve some CONFIG options
- deprecate 'make kvmconfig' and 'make xenconfig' in favor of
'make kvm_guest.config' and 'make xen.config'
- code cleanups
-----BEGIN PGP SIGNATURE-----
iQJJBAABCgAzFiEEbmPs18K1szRHjPqEPYsBB53g2wYFAl7bsBkVHG1hc2FoaXJv
eUBrZXJuZWwub3JnAAoJED2LAQed4NsGjgwP/17odsg7DK15nFXiT0A7A1VzMZpf
4oOjRo7W+J3zplEzLAFCf759Cov+MeqEdApzTWc+10bLXh5UlWBN8A1wof8dt5SV
uQZMDO90uqB/sIwTZc8PJrn+9PiGl8D0L/WHMBOvz1AYaK8SBnB6xO0Xf/mn/AFX
xpjxOhkUjTO59sNn8X3xjgDROkLp/iD3aC0sxo88U30n1aoV2surkPbG2/X879M4
Q+sW1phPqXoC9WsOJHmsWOx5IdZoj2hy0z4uWGGjXuZwimNQd2PnhuhRg0xfp+WN
8OYK4B74gnTAAFh2AyQu89DcNCiBYMGwRlrPrsvszODsUZjjgAPWouDpvrwVHf+R
fZDTPtccQK4BELxIg3lbPCQPfzTDXfsxcK7R4X2AizdLKsh6yI5mdqGR0XcCxCyH
gEtBNDHsMt4X4g4Z916cvewCmr5dmz+gAKem83j5fPhmVddMCcBgd6W8Dj9NUzGs
cloHhs9gOGt0w+xBWGftcWARW4/wTf+Dn0yJ6QAaobq/QwMLFDWv8rDy0xzLttjA
ISNetBUofolmvKiLqgblwY66yCgDzLJhNhR0L8jEJTMGq02Bi76BwnADlr3vnraw
Bx4tmAoVGx+JXw/TrEY7Be5u/Ji/ofv7YTN9RZZOD9m5Om5HD3zFbtCXN+/8t83D
2iD1imSJ0TQId36y
=FlOD
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig updates from Masahiro Yamada:
- allow only 'config', 'comment', 'if' statements inside 'choice' since
the other statements are not sensible inside 'choice' and should be
grammatical error
- support LMC_KEEP env variable for 'make local{yes,mod}config' to
preserve some CONFIG options
- deprecate 'make kvmconfig' and 'make xenconfig' in favor of
'make kvm_guest.config' and 'make xen.config'
- code cleanups
* tag 'kconfig-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: announce removal of 'kvmconfig' and 'xenconfig' shorthands
streamline_config.pl: add LMC_KEEP to preserve some kconfigs
kconfig: allow only 'config', 'comment', and 'if' inside 'choice'
kconfig: tests: remove randconfig test for choice in choice
kconfig: do not assign a variable in the return statement
kconfig: do not use OR-assignment for zero-cleared structure
Pull cgroup updates from Tejun Heo:
"Just two patches: one to add system-level cpu.stat to the root cgroup
for convenience and a trivial comment update"
* 'for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: add cpu.stat file to root cgroup
cgroup: Remove stale comments
version 2 feature that adds support for pairing regular block
devices with a zoned device to ease performance impact associated
with finite random zones of zoned device. Changes came in 3
batches: first prepared for and then added the ability to pair a
single regular block device, second was a batch of fixes to improve
zoned's reclaim heuristic, third removed the limitation of only
adding a single additional regular block device to allow many
devices. Testing has shown linear scaling as more devices are
added.
- Add new emulated block size (ebs) target that emulates a smaller
logical_block_size than a block device supports. Primary use-case
is to emulate "512e" devices that have 512 byte logical_block_size
and 4KB physical_block_size. This is useful to some legacy
applications otherwise wouldn't be ablee to be used on 4K devices
because they depend on issuing IO in 512 byte granularity.
- Add discard interfaces to DM bufio. First consumer of the interface
is the dm-ebs target that makes heavy use of dm-bufio.
- Fix DM crypt's block queue_limits stacking to not truncate
logic_block_size.
- Add Documentation for DM integrity's status line.
- Switch DMDEBUG from a compile time config option to instead use
dynamic debug via pr_debug.
- Fix DM multipath target's hueristic for how it manages
"queue_if_no_path" state internally. DM multipath now avoids
disabling "queue_if_no_path" unless it is actually needed (e.g. in
response to configure timeout or explicit "fail_if_no_path"
message). This fixes reports of spurious -EIO being reported back
to userspace application during fault tolerance testing with an NVMe
backend. Added various dynamic DMDEBUG messages to assist with
debugging queue_if_no_path in the future.
- Add a new DM multipath "Historical Service Time" Path Selector.
- Fix DM multipath's dm_blk_ioctl() to switch paths on IO error.
- Improve DM writecache target performance by using explicit
cache flushing for target's single-threaded usecase and a small
cleanup to remove unnecessary test in persistent_memory_claim.
- Other small cleanups in DM core, dm-persistent-data, and DM integrity.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEJfWUX4UqZ4x1O2wixSPxCi2dA1oFAl7alrgTHHNuaXR6ZXJA
cmVkaGF0LmNvbQAKCRDFI/EKLZ0DWl42B/9sBd+j60emy4Bliu/f3pd7SEkFrSXv
K2jXicRFx4E5kO0aLK+fX65cOiq2vvLsDh8c++0TLXcD9q7oK0qxK9c8TCPq29Cx
W2J2dwdjyyqqbr3/FZHYYM9KLOl5rsxJLygXwhJhQ2Gny44L7nVACrAXNzXIHJ3r
f8xr+GLdF/jz7WLj8bwEDo3Bf8wvxDvl2ijqj7EceOhTutNE8xHQ6UcTPqTtozJy
sNM8UQNk1L43DBAvXfrKZ+yQ5DYAKdXKJpV9C8qv5DEGbaEikuMrHddgO4KlDdp4
VjPk9GSfPwGcJ4ecN8vgecZVGvh52ZU7OZ8qey/q0zqps74jeHTZQQyM
=jRun
-----END PGP SIGNATURE-----
Merge tag 'for-5.8/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- The largest change for this cycle is the DM zoned target's metadata
version 2 feature that adds support for pairing regular block devices
with a zoned device to ease the performance impact associated with
finite random zones of zoned device.
The changes came in three batches: the first prepared for and then
added the ability to pair a single regular block device, the second
was a batch of fixes to improve zoned's reclaim heuristic, and the
third removed the limitation of only adding a single additional
regular block device to allow many devices.
Testing has shown linear scaling as more devices are added.
- Add new emulated block size (ebs) target that emulates a smaller
logical_block_size than a block device supports
The primary use-case is to emulate "512e" devices that have 512 byte
logical_block_size and 4KB physical_block_size. This is useful to
some legacy applications that otherwise wouldn't be able to be used
on 4K devices because they depend on issuing IO in 512 byte
granularity.
- Add discard interfaces to DM bufio. First consumer of the interface
is the dm-ebs target that makes heavy use of dm-bufio.
- Fix DM crypt's block queue_limits stacking to not truncate
logic_block_size.
- Add Documentation for DM integrity's status line.
- Switch DMDEBUG from a compile time config option to instead use
dynamic debug via pr_debug.
- Fix DM multipath target's hueristic for how it manages
"queue_if_no_path" state internally.
DM multipath now avoids disabling "queue_if_no_path" unless it is
actually needed (e.g. in response to configure timeout or explicit
"fail_if_no_path" message).
This fixes reports of spurious -EIO being reported back to userspace
application during fault tolerance testing with an NVMe backend.
Added various dynamic DMDEBUG messages to assist with debugging
queue_if_no_path in the future.
- Add a new DM multipath "Historical Service Time" Path Selector.
- Fix DM multipath's dm_blk_ioctl() to switch paths on IO error.
- Improve DM writecache target performance by using explicit cache
flushing for target's single-threaded usecase and a small cleanup to
remove unnecessary test in persistent_memory_claim.
- Other small cleanups in DM core, dm-persistent-data, and DM
integrity.
* tag 'for-5.8/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (62 commits)
dm crypt: avoid truncating the logical block size
dm mpath: add DM device name to Failing/Reinstating path log messages
dm mpath: enhance queue_if_no_path debugging
dm mpath: restrict queue_if_no_path state machine
dm mpath: simplify __must_push_back
dm zoned: check superblock location
dm zoned: prefer full zones for reclaim
dm zoned: select reclaim zone based on device index
dm zoned: allocate zone by device index
dm zoned: support arbitrary number of devices
dm zoned: move random and sequential zones into struct dmz_dev
dm zoned: per-device reclaim
dm zoned: add metadata pointer to struct dmz_dev
dm zoned: add device pointer to struct dm_zone
dm zoned: allocate temporary superblock for tertiary devices
dm zoned: convert to xarray
dm zoned: add a 'reserved' zone flag
dm zoned: improve logging messages for reclaim
dm zoned: avoid unnecessary device recalulation for secondary superblock
dm zoned: add debugging message for reading superblocks
...
Core changes:
- A new GPIO aggregator driver has been merged: this can
join a few select GPIO lines into a new aggregated GPIO
chip. This can be used for security: a process can be
granted access to only these lines, for example for
industrial control. Another way to use this is to
reexpose certain select lines to a virtual machine or
container.
- Warn if the gpio-line-names is too long in he DT parser
core.
- GPIO lines can now be looked up by line name in addition
to being looked up by offset.
New drivers:
- A new generic regmap GPIO driver has been merged. Too
many regmap drivers are starting to look like each other
so we need to create some common ground and try to move
drivers over to using that.
- The F7188X driver now supports F81865.
Driver improvements:
- Large improvements to the PCA953x expander, get multiple lines
and several cleanups.
- Large improvements to the DesignWare DWAPB driver, and Sergey
Semin has volunteered to maintain it.
- PL061 can now be built as a module, this is part of a bigger
effort to make the ARM platforms more modular.
-----BEGIN PGP SIGNATURE-----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=B5OK
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.8 kernel cycle.
Core changes:
- A new GPIO aggregator driver has been merged: this can join a few
select GPIO lines into a new aggregated GPIO chip. This can be used
for security: a process can be granted access to only these lines,
for example for industrial control. Another way to use this is to
reexpose certain select lines to a virtual machine or container.
- Warn if the gpio-line-names is too long in he DT parser core.
- GPIO lines can now be looked up by line name in addition to being
looked up by offset.
New drivers:
- A new generic regmap GPIO driver has been merged. Too many regmap
drivers are starting to look like each other so we need to create
some common ground and try to move drivers over to using that.
- The F7188X driver now supports F81865.
Driver improvements:
- Large improvements to the PCA953x expander, get multiple lines and
several cleanups.
- Large improvements to the DesignWare DWAPB driver, and Sergey Semin
has volunteered to maintain it.
- PL061 can now be built as a module, this is part of a bigger effort
to make the ARM platforms more modular"
* tag 'gpio-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: pca953x: Drop unneeded ACPI_PTR()
MAINTAINERS: Add gpio regmap section
gpio: add a reusable generic gpio_chip using regmap
gpiolib: Introduce gpiochip_irqchip_add_domain()
gpio: gpiolib: Allow GPIO IRQs to lazy disable
gpiolib: Separate GPIO_GET_LINEINFO_WATCH_IOCTL conditional
gpio: rcar: Fix runtime PM imbalance on error
gpio: pca935x: Allow IRQ support for driver built as a module
gpio: pxa: Add COMPILE_TEST support
dt-bindings: gpio: Add renesas,em-gio bindings
MAINTAINERS: Fix file name for DesignWare GPIO DT schema
gpio: dwapb: Remove unneeded has_irq member in struct dwapb_port_property
gpio: dwapb: Don't use IRQ 0 as valid Linux interrupt
gpio: dwapb: avoid error message for optional IRQ
gpio: dwapb: Call acpi_gpiochip_free_interrupts() on GPIO chip de-registration
gpio: max730x: bring gpiochip_add_data after port config
MAINTAINERS: Add GPIO Aggregator section
docs: gpio: Add GPIO Aggregator documentation
gpio: Add GPIO Aggregator
gpiolib: Add support for GPIO lookup by line name
...
- Support for userspace to send requests directly to the on-chip GZIP
accelerator on Power9.
- Rework of our lockless page table walking (__find_linux_pte()) to make it
safe against parallel page table manipulations without relying on an IPI for
serialisation.
- A series of fixes & enhancements to make our machine check handling more
robust.
- Lots of plumbing to add support for "prefixed" (64-bit) instructions on
Power10.
- Support for using huge pages for the linear mapping on 8xx (32-bit).
- Remove obsolete Xilinx PPC405/PPC440 support, and an associated sound driver.
- Removal of some obsolete 40x platforms and associated cruft.
- Initial support for booting on Power10.
- Lots of other small features, cleanups & fixes.
Thanks to:
Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan, Andrey Abramov,
Aneesh Kumar K.V, Balamuruhan S, Bharata B Rao, Bulent Abali, Cédric Le
Goater, Chen Zhou, Christian Zigotzky, Christophe JAILLET, Christophe Leroy,
Dmitry Torokhov, Emmanuel Nicolet, Erhard F., Gautham R. Shenoy, Geoff Levand,
George Spelvin, Greg Kurz, Gustavo A. R. Silva, Gustavo Walbon, Haren Myneni,
Hari Bathini, Joel Stanley, Jordan Niethe, Kajol Jain, Kees Cook, Leonardo
Bras, Madhavan Srinivasan., Mahesh Salgaonkar, Markus Elfring, Michael
Neuling, Michal Simek, Nathan Chancellor, Nathan Lynch, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pingfan Liu, Qian Cai, Ram
Pai, Raphael Moreira Zinsly, Ravi Bangoria, Sam Bobroff, Sandipan Das, Segher
Boessenkool, Stephen Rothwell, Sukadev Bhattiprolu, Tyrel Datwyler, Wolfram
Sang, Xiongfeng Wang.
-----BEGIN PGP SIGNATURE-----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=o0WU
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Support for userspace to send requests directly to the on-chip GZIP
accelerator on Power9.
- Rework of our lockless page table walking (__find_linux_pte()) to
make it safe against parallel page table manipulations without
relying on an IPI for serialisation.
- A series of fixes & enhancements to make our machine check handling
more robust.
- Lots of plumbing to add support for "prefixed" (64-bit) instructions
on Power10.
- Support for using huge pages for the linear mapping on 8xx (32-bit).
- Remove obsolete Xilinx PPC405/PPC440 support, and an associated sound
driver.
- Removal of some obsolete 40x platforms and associated cruft.
- Initial support for booting on Power10.
- Lots of other small features, cleanups & fixes.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan,
Andrey Abramov, Aneesh Kumar K.V, Balamuruhan S, Bharata B Rao, Bulent
Abali, Cédric Le Goater, Chen Zhou, Christian Zigotzky, Christophe
JAILLET, Christophe Leroy, Dmitry Torokhov, Emmanuel Nicolet, Erhard F.,
Gautham R. Shenoy, Geoff Levand, George Spelvin, Greg Kurz, Gustavo A.
R. Silva, Gustavo Walbon, Haren Myneni, Hari Bathini, Joel Stanley,
Jordan Niethe, Kajol Jain, Kees Cook, Leonardo Bras, Madhavan
Srinivasan., Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Michal
Simek, Nathan Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin,
Oliver O'Halloran, Paul Mackerras, Pingfan Liu, Qian Cai, Ram Pai,
Raphael Moreira Zinsly, Ravi Bangoria, Sam Bobroff, Sandipan Das, Segher
Boessenkool, Stephen Rothwell, Sukadev Bhattiprolu, Tyrel Datwyler,
Wolfram Sang, Xiongfeng Wang.
* tag 'powerpc-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (299 commits)
powerpc/pseries: Make vio and ibmebus initcalls pseries specific
cxl: Remove dead Kconfig options
powerpc: Add POWER10 architected mode
powerpc/dt_cpu_ftrs: Add MMA feature
powerpc/dt_cpu_ftrs: Enable Prefixed Instructions
powerpc/dt_cpu_ftrs: Advertise support for ISA v3.1 if selected
powerpc: Add support for ISA v3.1
powerpc: Add new HWCAP bits
powerpc/64s: Don't set FSCR bits in INIT_THREAD
powerpc/64s: Save FSCR to init_task.thread.fscr after feature init
powerpc/64s: Don't let DT CPU features set FSCR_DSCR
powerpc/64s: Don't init FSCR_DSCR in __init_FSCR()
powerpc/32s: Fix another build failure with CONFIG_PPC_KUAP_DEBUG
powerpc/module_64: Use special stub for _mcount() with -mprofile-kernel
powerpc/module_64: Simplify check for -mprofile-kernel ftrace relocations
powerpc/module_64: Consolidate ftrace code
powerpc/32: Disable KASAN with pages bigger than 16k
powerpc/uaccess: Don't set KUEP by default on book3s/32
powerpc/uaccess: Don't set KUAP by default on book3s/32
powerpc/8xx: Reduce time spent in allow_user_access() and friends
...
-----BEGIN PGP SIGNATURE-----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=KNAo
-----END PGP SIGNATURE-----
Merge tag 'media/v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Media documentation is now split into admin-guide, driver-api and
userspace-api books (a longstanding request from Jon);
- The media Kconfig was reorganized, in order to make easier to select
drivers and their dependencies;
- The testing drivers now has a separate directory;
- added a new driver for Rockchip Video Decoder IP;
- The atomisp staging driver was resurrected. It is meant to work with
4 generations of cameras on Atom-based laptops, tablets and cell
phones. So, it seems worth investing time to cleanup this driver and
making it in good shape.
- Added some V4L2 core ancillary routines to help with h264 codecs;
- Added an ov2740 image sensor driver;
- The si2157 gained support for Analog TV, which, in turn, added
support for some cx231xx and cx23885 boards to also support analog
standards;
- Added some V4L2 controls (V4L2_CID_CAMERA_ORIENTATION and
V4L2_CID_CAMERA_SENSOR_ROTATION) to help identifying where the camera
is located at the device;
- VIDIOC_ENUM_FMT was extended to support MC-centric devices;
- Lots of drivers improvements and cleanups.
* tag 'media/v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (503 commits)
media: Documentation: media: Refer to mbus format documentation from CSI-2 docs
media: s5k5baf: Replace zero-length array with flexible-array
media: i2c: imx219: Drop <linux/clk-provider.h> and <linux/clkdev.h>
media: i2c: Add ov2740 image sensor driver
media: ov8856: Implement sensor module revision identification
media: ov8856: Add devicetree support
media: dt-bindings: ov8856: Document YAML bindings
media: dvb-usb: Add Cinergy S2 PCIe Dual Port support
media: dvbdev: Fix tuner->demod media controller link
media: dt-bindings: phy: phy-rockchip-dphy-rx0: move rockchip dphy rx0 bindings out of staging
media: staging: dt-bindings: phy-rockchip-dphy-rx0: remove non-used reg property
media: atomisp: unify the version for isp2401 a0 and b0 versions
media: atomisp: update TODO with the current data
media: atomisp: adjust some code at sh_css that could be broken
media: atomisp: don't produce errs for ignored IRQs
media: atomisp: print IRQ when debugging
media: atomisp: isp_mmu: don't use kmem_cache
media: atomisp: add a notice about possible leak resources
media: atomisp: disable the dynamic and reserved pools
media: atomisp: turn on camera before setting it
...
Merge more updates from Andrew Morton:
"More mm/ work, plenty more to come
Subsystems affected by this patch series: slub, memcg, gup, kasan,
pagealloc, hugetlb, vmscan, tools, mempolicy, memblock, hugetlbfs,
thp, mmap, kconfig"
* akpm: (131 commits)
arm64: mm: use ARCH_HAS_DEBUG_WX instead of arch defined
x86: mm: use ARCH_HAS_DEBUG_WX instead of arch defined
riscv: support DEBUG_WX
mm: add DEBUG_WX support
drivers/base/memory.c: cache memory blocks in xarray to accelerate lookup
mm/thp: rename pmd_mknotpresent() as pmd_mkinvalid()
powerpc/mm: drop platform defined pmd_mknotpresent()
mm: thp: don't need to drain lru cache when splitting and mlocking THP
hugetlbfs: get unmapped area below TASK_UNMAPPED_BASE for hugetlbfs
sparc32: register memory occupied by kernel as memblock.memory
include/linux/memblock.h: fix minor typo and unclear comment
mm, mempolicy: fix up gup usage in lookup_node
tools/vm/page_owner_sort.c: filter out unneeded line
mm: swap: memcg: fix memcg stats for huge pages
mm: swap: fix vmstats for huge pages
mm: vmscan: limit the range of LRU type balancing
mm: vmscan: reclaim writepage is IO cost
mm: vmscan: determine anon/file pressure balance at the reclaim root
mm: balance LRU lists based on relative thrashing
mm: only count actual rotations as LRU reclaim cost
...
With the advent of fast random IO devices (SSDs, PMEM) and in-memory swap
devices such as zswap, it's possible for swap to be much faster than
filesystems, and for swapping to be preferable over thrashing filesystem
caches.
Allow setting swappiness - which defines the rough relative IO cost of
cache misses between page cache and swap-backed pages - to reflect such
situations by making the swap-preferred range configurable.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-4-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With all hugetlb page processing done in a single file clean up code.
- Make code match desired semantics
- Update documentation with semantics
- Make all warnings and errors messages start with 'HugeTLB:'.
- Consistently name command line parsing routines.
- Warn if !hugepages_supported() and command line parameters have
been specified.
- Add comments to code
- Describe some of the subtle interactions
- Describe semantics of command line arguments
This patch also fixes issues with implicitly setting the number of
gigantic huge pages to preallocate. Previously on X86 command line,
hugepages=2 default_hugepagesz=1G
would result in zero 1G pages being preallocated and,
# grep HugePages_Total /proc/meminfo
HugePages_Total: 0
# sysctl -a | grep nr_hugepages
vm.nr_hugepages = 2
vm.nr_hugepages_mempolicy = 2
# cat /proc/sys/vm/nr_hugepages
2
After this patch 2 gigantic pages will be preallocated and all the proc,
sysfs, sysctl and meminfo files will accurately reflect this.
To address the issue with gigantic pages, a small change in behavior was
made to command line processing. Previously the command line,
hugepages=128 default_hugepagesz=2M hugepagesz=2M hugepages=256
would result in the allocation of 256 2M huge pages. The value 128 would
be ignored without any warning. After this patch, 128 2M pages will be
allocated and a warning message will be displayed indicating the value of
256 is ignored. This change in behavior is required because allocation of
implicitly specified gigantic pages must be done when the
default_hugepagesz= is encountered for gigantic pages. Previously the
code waited until later in the boot process (hugetlb_init), to allocate
pages of default size. However the bootmem allocator required for
gigantic allocations is not available at this time.
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Sandipan Das <sandipan@linux.ibm.com>
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Will Deacon <will@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Longpeng <longpeng2@huawei.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nitesh Narayan Lal <nitesh@redhat.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/20200417185049.275845-5-mike.kravetz@oracle.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'max_ptes_shared' specifies how many pages can be shared across multiple
processes. Exceeding the number would block the collapse::
/sys/kernel/mm/transparent_hugepage/khugepaged/max_ptes_shared
A higher value may increase memory footprint for some workloads.
By default, at least half of pages has to be not shared.
[colin.king@canonical.com: fix several spelling mistakes]
Link: http://lkml.kernel.org/r/20200420084241.65433-1-colin.king@canonical.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Zi Yan <ziy@nvidia.com>
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Reviewed-by: Zi Yan <ziy@nvidia.com>
Acked-by: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Link: http://lkml.kernel.org/r/20200416160026.16538-9-kirill.shutemov@linux.intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
By far the biggest change in this cycle are the changes that allow much
earlier debug of systems that are hooked up via UART by taking advantage
of the earlycon framework to implement the kgdb I/O hooks before handing
over to the regular polling I/O drivers once they are available. When
discussing Doug's work we also found and fixed an broken
raw_smp_processor_id() sequence in in_dbg_master().
Also included are a collection of much smaller fixes and tweaks: a
couple of tweaks to ged rid of doc gen or coccicheck warnings, future
proof some internal calculations that made implicit power-of-2
assumptions and eliminate some rather weird handling of magic
environment variables in kdb.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=uLAB
-----END PGP SIGNATURE-----
Merge tag 'kgdb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"By far the biggest change in this cycle are the changes that allow
much earlier debug of systems that are hooked up via UART by taking
advantage of the earlycon framework to implement the kgdb I/O hooks
before handing over to the regular polling I/O drivers once they are
available. When discussing Doug's work we also found and fixed an
broken raw_smp_processor_id() sequence in in_dbg_master().
Also included are a collection of much smaller fixes and tweaks: a
couple of tweaks to ged rid of doc gen or coccicheck warnings, future
proof some internal calculations that made implicit power-of-2
assumptions and eliminate some rather weird handling of magic
environment variables in kdb"
* tag 'kgdb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
kdb: Remove the misfeature 'KDBFLAGS'
kdb: Cleanup math with KDB_CMD_HISTORY_COUNT
serial: amba-pl011: Support kgdboc_earlycon
serial: 8250_early: Support kgdboc_earlycon
serial: qcom_geni_serial: Support kgdboc_earlycon
serial: kgdboc: Allow earlycon initialization to be deferred
Documentation: kgdboc: Document new kgdboc_earlycon parameter
kgdb: Don't call the deinit under spinlock
kgdboc: Disable all the early code when kgdboc is a module
kgdboc: Add kgdboc_earlycon to support early kgdb using boot consoles
kgdboc: Remove useless #ifdef CONFIG_KGDB_SERIAL_CONSOLE in kgdboc
kgdb: Prevent infinite recursive entries to the debugger
kgdb: Delay "kgdbwait" to dbg_late_init() by default
kgdboc: Use a platform device to handle tty drivers showing up late
Revert "kgdboc: disable the console lock when in kgdb"
kgdb: Disable WARN_CONSOLE_UNLOCKED for all kgdb
kgdb: Return true in kgdb_nmi_poll_knock()
kgdb: Drop malformed kernel doc comment
kgdb: Fix spurious true from in_dbg_master()
- Add TPAUSE based delay which allows the CPU to enter an optimized power
state while waiting for the delay to pass. The delay is based on TSC
cycles.
- Add tsc_early_khz command line parameter to workaround the problem that
overclocked CPUs can report the wrong frequency via CPUID.16h which
causes the refined calibration to fail because the delta to the initial
frequency value is too big. With the parameter users can provide an
halfways accurate initial value.
-----BEGIN PGP SIGNATURE-----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=199V
-----END PGP SIGNATURE-----
Merge tag 'x86-timers-2020-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 timer updates from Thomas Gleixner:
"X86 timer specific updates:
- Add TPAUSE based delay which allows the CPU to enter an optimized
power state while waiting for the delay to pass. The delay is based
on TSC cycles.
- Add tsc_early_khz command line parameter to workaround the problem
that overclocked CPUs can report the wrong frequency via CPUID.16h
which causes the refined calibration to fail because the delta to
the initial frequency value is too big. With the parameter users
can provide an halfways accurate initial value"
* tag 'x86-timers-2020-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Add tsc_early_khz command line parameter
x86/delay: Introduce TPAUSE delay
x86/delay: Refactor delay_mwaitx() for TPAUSE support
x86/delay: Preparatory code cleanup
- Rework the system-wide PM driver flags to make them easier to
understand and use and update their documentation (Rafael Wysocki,
Alan Stern).
- Allow cpuidle governors to be switched at run time regardless of
the kernel configuration and update the related documentation
accordingly (Hanjun Guo).
- Improve the resume device handling in the user space hibernarion
interface code (Domenico Andreoli).
- Document the intel-speed-select sysfs interface (Srinivas
Pandruvada).
- Make the ACPI code handing suspend to idle print more debug
messages to help diagnose issues with it (Rafael Wysocki).
- Fix a helper routine in the cpufreq core and correct a typo in
the struct cpufreq_driver kerneldoc comment (Rafael Wysocki, Wang
Wenhu).
- Update cpufreq drivers:
* Make the intel_pstate driver start in the passive mode by
default on systems without HWP (Rafael Wysocki).
* Add i.MX7ULP support to the imx-cpufreq-dt driver and add
i.MX7ULP to the cpufreq-dt-platdev blacklist (Peng Fan).
* Convert the qoriq cpufreq driver to a platform one, make the
platform code create a suitable device object for it and add
platform dependencies to it (Mian Yousaf Kaukab, Geert
Uytterhoeven).
* Fix wrong compatible binding in the qcom driver (Ansuel Smith).
* Build the omap driver by default for ARCH_OMAP2PLUS (Anders
Roxell).
* Add r8a7742 SoC support to the dt cpufreq driver (Lad Prabhakar).
- Update cpuidle core and drivers:
* Fix three reference count leaks in error code paths in the
cpuidle core (Qiushi Wu).
* Convert Qualcomm SPM to a generic cpuidle driver (Stephan
Gerhold).
* Fix up the execution order when entering a domain idle state in
the PSCI driver (Ulf Hansson).
- Fix a reference counting issue related to clock management and
clean up two oddities in the PM-runtime framework (Rafael Wysocki,
Andy Shevchenko).
- Add ElkhartLake support to the Intel RAPL power capping driver
and remove an unused local MSR definition from it (Jacob Pan,
Sumeet Pawnikar).
- Update devfreq core and drivers:
* Replace strncpy() with strscpy() in the devfreq core and use
lockdep asserts instead of manual checks for a locked mutex in
it (Dmitry Osipenko, Krzysztof Kozlowski).
* Add a generic imx bus scaling driver and make it register an
interconnect device (Leonard Crestez, Gustavo A. R. Silva).
* Make the cpufreq notifier in the tegra30 driver take boosting
into account and delete an unuseful error message from that
driver (Dmitry Osipenko, Markus Elfring).
- Remove unneeded semicolon from the cpupower code (Zou Wei).
-----BEGIN PGP SIGNATURE-----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=APdj
-----END PGP SIGNATURE-----
Merge tag 'pm-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These rework the system-wide PM driver flags, make runtime switching
of cpuidle governors easier, improve the user space hibernation
interface code, add intel-speed-select interface documentation, add
more debug messages to the ACPI code handling suspend to idle, update
the cpufreq core and drivers, fix a minor issue in the cpuidle core
and update two cpuidle drivers, improve the PM-runtime framework,
update the Intel RAPL power capping driver, update devfreq core and
drivers, and clean up the cpupower utility.
Specifics:
- Rework the system-wide PM driver flags to make them easier to
understand and use and update their documentation (Rafael Wysocki,
Alan Stern).
- Allow cpuidle governors to be switched at run time regardless of
the kernel configuration and update the related documentation
accordingly (Hanjun Guo).
- Improve the resume device handling in the user space hibernarion
interface code (Domenico Andreoli).
- Document the intel-speed-select sysfs interface (Srinivas
Pandruvada).
- Make the ACPI code handing suspend to idle print more debug
messages to help diagnose issues with it (Rafael Wysocki).
- Fix a helper routine in the cpufreq core and correct a typo in the
struct cpufreq_driver kerneldoc comment (Rafael Wysocki, Wang
Wenhu).
- Update cpufreq drivers:
- Make the intel_pstate driver start in the passive mode by
default on systems without HWP (Rafael Wysocki).
- Add i.MX7ULP support to the imx-cpufreq-dt driver and add
i.MX7ULP to the cpufreq-dt-platdev blacklist (Peng Fan).
- Convert the qoriq cpufreq driver to a platform one, make the
platform code create a suitable device object for it and add
platform dependencies to it (Mian Yousaf Kaukab, Geert
Uytterhoeven).
- Fix wrong compatible binding in the qcom driver (Ansuel Smith).
- Build the omap driver by default for ARCH_OMAP2PLUS (Anders
Roxell).
- Add r8a7742 SoC support to the dt cpufreq driver (Lad
Prabhakar).
- Update cpuidle core and drivers:
- Fix three reference count leaks in error code paths in the
cpuidle core (Qiushi Wu).
- Convert Qualcomm SPM to a generic cpuidle driver (Stephan
Gerhold).
- Fix up the execution order when entering a domain idle state in
the PSCI driver (Ulf Hansson).
- Fix a reference counting issue related to clock management and
clean up two oddities in the PM-runtime framework (Rafael Wysocki,
Andy Shevchenko).
- Add ElkhartLake support to the Intel RAPL power capping driver and
remove an unused local MSR definition from it (Jacob Pan, Sumeet
Pawnikar).
- Update devfreq core and drivers:
- Replace strncpy() with strscpy() in the devfreq core and use
lockdep asserts instead of manual checks for a locked mutex in
it (Dmitry Osipenko, Krzysztof Kozlowski).
- Add a generic imx bus scaling driver and make it register an
interconnect device (Leonard Crestez, Gustavo A. R. Silva).
- Make the cpufreq notifier in the tegra30 driver take boosting
into account and delete an unuseful error message from that
driver (Dmitry Osipenko, Markus Elfring).
- Remove unneeded semicolon from the cpupower code (Zou Wei)"
* tag 'pm-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (51 commits)
cpuidle: Fix three reference count leaks
PM: runtime: Replace pm_runtime_callbacks_present()
PM / devfreq: Use lockdep asserts instead of manual checks for locked mutex
PM / devfreq: imx-bus: Fix inconsistent IS_ERR and PTR_ERR
PM / devfreq: Replace strncpy with strscpy
PM / devfreq: imx: Register interconnect device
PM / devfreq: Add generic imx bus scaling driver
PM / devfreq: tegra30: Delete an error message in tegra_devfreq_probe()
PM / devfreq: tegra30: Make CPUFreq notifier to take into account boosting
PM: hibernate: Restrict writes to the resume device
PM: runtime: clk: Fix clk_pm_runtime_get() error path
cpuidle: Convert Qualcomm SPM driver to a generic CPUidle driver
ACPI: EC: PM: s2idle: Extend GPE dispatching debug message
ACPI: PM: s2idle: Print type of wakeup debug messages
powercap: RAPL: remove unused local MSR define
PM: runtime: Make clear what we do when conditions are wrong in rpm_suspend()
Documentation: admin-guide: pm: Document intel-speed-select
PM: hibernate: Split off snapshot dev option
PM: hibernate: Incorporate concurrency handling
Documentation: ABI: make current_governer_ro as a candidate for removal
...
Merge updates from Andrew Morton:
"A few little subsystems and a start of a lot of MM patches.
Subsystems affected by this patch series: squashfs, ocfs2, parisc,
vfs. With mm subsystems: slab-generic, slub, debug, pagecache, gup,
swap, memcg, pagemap, memory-failure, vmalloc, kasan"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
kasan: move kasan_report() into report.c
mm/mm_init.c: report kasan-tag information stored in page->flags
ubsan: entirely disable alignment checks under UBSAN_TRAP
kasan: fix clang compilation warning due to stack protector
x86/mm: remove vmalloc faulting
mm: remove vmalloc_sync_(un)mappings()
x86/mm/32: implement arch_sync_kernel_mappings()
x86/mm/64: implement arch_sync_kernel_mappings()
mm/ioremap: track which page-table levels were modified
mm/vmalloc: track which page-table levels were modified
mm: add functions to track page directory modifications
s390: use __vmalloc_node in stack_alloc
powerpc: use __vmalloc_node in alloc_vm_stack
arm64: use __vmalloc_node in arch_alloc_vmap_stack
mm: remove vmalloc_user_node_flags
mm: switch the test_vmalloc module to use __vmalloc_node
mm: remove __vmalloc_node_flags_caller
mm: remove both instances of __vmalloc_node_flags
mm: remove the prot argument to __vmalloc_node
mm: remove the pgprot argument to __vmalloc
...
Add a memory.swap.high knob, which can be used to protect the system
from SWAP exhaustion. The mechanism used for penalizing is similar to
memory.high penalty (sleep on return to user space).
That is not to say that the knob itself is equivalent to memory.high.
The objective is more to protect the system from potentially buggy tasks
consuming a lot of swap and impacting other tasks, or even bringing the
whole system to stand still with complete SWAP exhaustion. Hopefully
without the need to find per-task hard limits.
Slowing misbehaving tasks down gradually allows user space oom killers
or other protection mechanisms to react. oomd and earlyoom already do
killing based on swap exhaustion, and memory.swap.high protection will
help implement such userspace oom policies more reliably.
We can use one counter for number of pages allocated under pressure to
save struct task space and avoid two separate hierarchy walks on the hot
path. The exact overage is calculated on return to user space, anyway.
Take the new high limit into account when determining if swap is "full".
Borrowing the explanation from Johannes:
The idea behind "swap full" is that as long as the workload has plenty
of swap space available and it's not changing its memory contents, it
makes sense to generously hold on to copies of data in the swap device,
even after the swapin. A later reclaim cycle can drop the page without
any IO. Trading disk space for IO.
But the only two ways to reclaim a swap slot is when they're faulted
in and the references go away, or by scanning the virtual address space
like swapoff does - which is very expensive (one could argue it's too
expensive even for swapoff, it's often more practical to just reboot).
So at some point in the fill level, we have to start freeing up swap
slots on fault/swapin. Otherwise we could eventually run out of swap
slots while they're filled with copies of data that is also in RAM.
We don't want to OOM a workload because its available swap space is
filled with redundant cache.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Chris Down <chris@chrisdown.name>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Link: http://lkml.kernel.org/r/20200527195846.102707-5-kuba@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's a new workingset counter introduced in commit 1899ad18c6 ("mm:
workingset: tell cache transitions from workingset thrashing"). With
the help of this counter we can know the workingset is transitioning or
thrashing. To leverage the benifit of this counter to memcg, we should
introduce it into memory.stat. Then we could know the workingset of the
workload inside a memcg better.
Bellow is the verification of this new counter in memory.stat. Read a
file into the memory and then read it again to make these pages be
active. The size of this file is 1G. (memory.max is greater than file
size) The counters in memory.stat will be
inactive_file 0
active_file 1073639424
workingset_refault 0
workingset_activate 0
workingset_restore 0
workingset_nodereclaim 0
Trigger the memcg reclaim by setting a lower value to memory.high, and
then some pages will be demoted into inactive list, and then some pages
in the inactive list will be evicted into the storage.
inactive_file 498094080
active_file 310063104
workingset_refault 0
workingset_activate 0
workingset_restore 0
workingset_nodereclaim 0
Then recover the memory.high and read the file into memory again. As a
result of it, the transitioning will occur. Bellow is the result of
this transitioning,
inactive_file 498094080
active_file 575397888
workingset_refault 64746
workingset_activate 64746
workingset_restore 64746
workingset_nodereclaim 0
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Chris Down <chris@chrisdown.name>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Shakeel Butt <shakeelb@google.com>
Link: http://lkml.kernel.org/r/20200504153522.11553-1-laoar.shao@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent patch ("kgdboc: Add kgdboc_earlycon to support early kgdb
using boot consoles") adds a new kernel command line parameter.
Document it.
Note that the patch adding the feature does some comparing/contrasting
of "kgdboc_earlycon" vs. the existing "ekgdboc". See that patch for
more details, but briefly "ekgdboc" can be used _instead_ of "kgdboc"
and just makes "kgdboc" do its normal initialization early (only works
if your tty driver is already ready). The new "kgdboc_earlycon" works
in combination with "kgdboc" and is backed by boot consoles.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.9.I7d5eb42c6180c831d47aef1af44d0b8be3fac559@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
set from Mauro toward the completion of the RST conversion. I *really*
hope we are getting close to the end of this. Meanwhile, those patches
reach pretty far afield to update document references around the tree;
there should be no actual code changes there. There will be, alas, more of
the usual trivial merge conflicts.
Beyond that we have more translations, improvements to the sphinx
scripting, a number of additions to the sysctl documentation, and lots of
fixes.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl7VId8PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yq/gH/iaDgirQZV6UZ2v9sfwQNYolNpf2sKAuOZjd
bPFB7WJoMQbKwQEvYrAUL2+5zPOcLYuIfzyOfo1BV1py+EyKbACcKjI4AedxfJF7
+NchmOBhlEqmEhzx2U08HRc4/8J223WG17fJRVsV3p+opJySexSFeQucfOciX5NR
RUCxweWWyg/FgyqjkyMMTtsePqZPmcT5dWTlVXISlbWzcv5NFhuJXnSrw8Sfzcmm
SJMzqItv3O+CabnKQ8kMLV2PozXTMfjeWH47ZUK0Y8/8PP9+cvqwFzZ0UDQJ1Xaz
oyW/TqmunaXhfMsMFeFGSwtfgwRHvXdxkQdtwNHvo1dV4dzTvDw=
=fDC/
-----END PGP SIGNATURE-----
Merge tag 'docs-5.8' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"A fair amount of stuff this time around, dominated by yet another
massive set from Mauro toward the completion of the RST conversion. I
*really* hope we are getting close to the end of this. Meanwhile,
those patches reach pretty far afield to update document references
around the tree; there should be no actual code changes there. There
will be, alas, more of the usual trivial merge conflicts.
Beyond that we have more translations, improvements to the sphinx
scripting, a number of additions to the sysctl documentation, and lots
of fixes"
* tag 'docs-5.8' of git://git.lwn.net/linux: (130 commits)
Documentation: fixes to the maintainer-entry-profile template
zswap: docs/vm: Fix typo accept_threshold_percent in zswap.rst
tracing: Fix events.rst section numbering
docs: acpi: fix old http link and improve document format
docs: filesystems: add info about efivars content
Documentation: LSM: Correct the basic LSM description
mailmap: change email for Ricardo Ribalda
docs: sysctl/kernel: document unaligned controls
Documentation: admin-guide: update bug-hunting.rst
docs: sysctl/kernel: document ngroups_max
nvdimm: fixes to maintainter-entry-profile
Documentation/features: Correct RISC-V kprobes support entry
Documentation/features: Refresh the arch support status files
Revert "docs: sysctl/kernel: document ngroups_max"
docs: move locking-specific documents to locking/
docs: move digsig docs to the security book
docs: move the kref doc into the core-api book
docs: add IRQ documentation at the core-api book
docs: debugging-via-ohci1394.txt: add it to the core-api book
docs: fix references for ipmi.rst file
...
- Branch Target Identification (BTI)
* Support for ARMv8.5-BTI in both user- and kernel-space. This
allows branch targets to limit the types of branch from which
they can be called and additionally prevents branching to
arbitrary code, although kernel support requires a very recent
toolchain.
* Function annotation via SYM_FUNC_START() so that assembly
functions are wrapped with the relevant "landing pad"
instructions.
* BPF and vDSO updates to use the new instructions.
* Addition of a new HWCAP and exposure of BTI capability to
userspace via ID register emulation, along with ELF loader
support for the BTI feature in .note.gnu.property.
* Non-critical fixes to CFI unwind annotations in the sigreturn
trampoline.
- Shadow Call Stack (SCS)
* Support for Clang's Shadow Call Stack feature, which reserves
platform register x18 to point at a separate stack for each
task that holds only return addresses. This protects function
return control flow from buffer overruns on the main stack.
* Save/restore of x18 across problematic boundaries (user-mode,
hypervisor, EFI, suspend, etc).
* Core support for SCS, should other architectures want to use it
too.
* SCS overflow checking on context-switch as part of the existing
stack limit check if CONFIG_SCHED_STACK_END_CHECK=y.
- CPU feature detection
* Removed numerous "SANITY CHECK" errors when running on a system
with mismatched AArch32 support at EL1. This is primarily a
concern for KVM, which disabled support for 32-bit guests on
such a system.
* Addition of new ID registers and fields as the architecture has
been extended.
- Perf and PMU drivers
* Minor fixes and cleanups to system PMU drivers.
- Hardware errata
* Unify KVM workarounds for VHE and nVHE configurations.
* Sort vendor errata entries in Kconfig.
- Secure Monitor Call Calling Convention (SMCCC)
* Update to the latest specification from Arm (v1.2).
* Allow PSCI code to query the SMCCC version.
- Software Delegated Exception Interface (SDEI)
* Unexport a bunch of unused symbols.
* Minor fixes to handling of firmware data.
- Pointer authentication
* Add support for dumping the kernel PAC mask in vmcoreinfo so
that the stack can be unwound by tools such as kdump.
* Simplification of key initialisation during CPU bringup.
- BPF backend
* Improve immediate generation for logical and add/sub
instructions.
- vDSO
- Minor fixes to the linker flags for consistency with other
architectures and support for LLVM's unwinder.
- Clean up logic to initialise and map the vDSO into userspace.
- ACPI
- Work around for an ambiguity in the IORT specification relating
to the "num_ids" field.
- Support _DMA method for all named components rather than only
PCIe root complexes.
- Minor other IORT-related fixes.
- Miscellaneous
* Initialise debug traps early for KGDB and fix KDB cacheflushing
deadlock.
* Minor tweaks to early boot state (documentation update, set
TEXT_OFFSET to 0x0, increase alignment of PE/COFF sections).
* Refactoring and cleanup
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl7U9csQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNLBHCACs/YU4SM7Om5f+7QnxIKao5DBr2CnGGvdC
yTfDghFDTLQVv3MufLlfno3yBe5G8sQpcZfcc+hewfcGoMzVZXu8s7LzH6VSn9T9
jmT3KjDMrg0RjSHzyumJp2McyelTk0a4FiKArSIIKsJSXUyb1uPSgm7SvKVDwEwU
JGDzL9IGilmq59GiXfDzGhTZgmC37QdwRoRxDuqtqWQe5CHoRXYexg87HwBKOQxx
HgU9L7ehri4MRZfpyjaDrr6quJo3TVnAAKXNBh3mZAskVS9ZrfKpEH0kYWYuqybv
znKyHRecl/rrGePV8RTMtrwnSdU26zMXE/omsVVauDfG9hqzqm+Q
=w3qi
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"A sizeable pile of arm64 updates for 5.8.
Summary below, but the big two features are support for Branch Target
Identification and Clang's Shadow Call stack. The latter is currently
arm64-only, but the high-level parts are all in core code so it could
easily be adopted by other architectures pending toolchain support
Branch Target Identification (BTI):
- Support for ARMv8.5-BTI in both user- and kernel-space. This allows
branch targets to limit the types of branch from which they can be
called and additionally prevents branching to arbitrary code,
although kernel support requires a very recent toolchain.
- Function annotation via SYM_FUNC_START() so that assembly functions
are wrapped with the relevant "landing pad" instructions.
- BPF and vDSO updates to use the new instructions.
- Addition of a new HWCAP and exposure of BTI capability to userspace
via ID register emulation, along with ELF loader support for the
BTI feature in .note.gnu.property.
- Non-critical fixes to CFI unwind annotations in the sigreturn
trampoline.
Shadow Call Stack (SCS):
- Support for Clang's Shadow Call Stack feature, which reserves
platform register x18 to point at a separate stack for each task
that holds only return addresses. This protects function return
control flow from buffer overruns on the main stack.
- Save/restore of x18 across problematic boundaries (user-mode,
hypervisor, EFI, suspend, etc).
- Core support for SCS, should other architectures want to use it
too.
- SCS overflow checking on context-switch as part of the existing
stack limit check if CONFIG_SCHED_STACK_END_CHECK=y.
CPU feature detection:
- Removed numerous "SANITY CHECK" errors when running on a system
with mismatched AArch32 support at EL1. This is primarily a concern
for KVM, which disabled support for 32-bit guests on such a system.
- Addition of new ID registers and fields as the architecture has
been extended.
Perf and PMU drivers:
- Minor fixes and cleanups to system PMU drivers.
Hardware errata:
- Unify KVM workarounds for VHE and nVHE configurations.
- Sort vendor errata entries in Kconfig.
Secure Monitor Call Calling Convention (SMCCC):
- Update to the latest specification from Arm (v1.2).
- Allow PSCI code to query the SMCCC version.
Software Delegated Exception Interface (SDEI):
- Unexport a bunch of unused symbols.
- Minor fixes to handling of firmware data.
Pointer authentication:
- Add support for dumping the kernel PAC mask in vmcoreinfo so that
the stack can be unwound by tools such as kdump.
- Simplification of key initialisation during CPU bringup.
BPF backend:
- Improve immediate generation for logical and add/sub instructions.
vDSO:
- Minor fixes to the linker flags for consistency with other
architectures and support for LLVM's unwinder.
- Clean up logic to initialise and map the vDSO into userspace.
ACPI:
- Work around for an ambiguity in the IORT specification relating to
the "num_ids" field.
- Support _DMA method for all named components rather than only PCIe
root complexes.
- Minor other IORT-related fixes.
Miscellaneous:
- Initialise debug traps early for KGDB and fix KDB cacheflushing
deadlock.
- Minor tweaks to early boot state (documentation update, set
TEXT_OFFSET to 0x0, increase alignment of PE/COFF sections).
- Refactoring and cleanup"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (148 commits)
KVM: arm64: Move __load_guest_stage2 to kvm_mmu.h
KVM: arm64: Check advertised Stage-2 page size capability
arm64/cpufeature: Add get_arm64_ftr_reg_nowarn()
ACPI/IORT: Remove the unused __get_pci_rid()
arm64/cpuinfo: Add ID_MMFR4_EL1 into the cpuinfo_arm64 context
arm64/cpufeature: Add remaining feature bits in ID_AA64PFR1 register
arm64/cpufeature: Add remaining feature bits in ID_AA64PFR0 register
arm64/cpufeature: Add remaining feature bits in ID_AA64ISAR0 register
arm64/cpufeature: Add remaining feature bits in ID_MMFR4 register
arm64/cpufeature: Add remaining feature bits in ID_PFR0 register
arm64/cpufeature: Introduce ID_MMFR5 CPU register
arm64/cpufeature: Introduce ID_DFR1 CPU register
arm64/cpufeature: Introduce ID_PFR2 CPU register
arm64/cpufeature: Make doublelock a signed feature in ID_AA64DFR0
arm64/cpufeature: Drop TraceFilt feature exposure from ID_DFR0 register
arm64/cpufeature: Add explicit ftr_id_isar0[] for ID_ISAR0 register
arm64: mm: Add asid_gen_match() helper
firmware: smccc: Fix missing prototype warning for arm_smccc_version_init
arm64: vdso: Fix CFI directives in sigreturn trampoline
arm64: vdso: Don't prefix sigreturn trampoline with a BTI C instruction
...
- Add the initrdmem= boot option to specify an initrd embedded in RAM (flash most likely)
- Sanitize the CS value earlier during boot, which also fixes SEV-ES.
- Various fixes and smaller cleanups.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=U/uh
-----END PGP SIGNATURE-----
Merge tag 'x86-boot-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 boot updates from Ingo Molnar:
"Misc updates:
- Add the initrdmem= boot option to specify an initrd embedded in RAM
(flash most likely)
- Sanitize the CS value earlier during boot, which also fixes SEV-ES
- Various fixes and smaller cleanups"
* tag 'x86-boot-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Correct relocation destination on old linkers
x86/boot/compressed/64: Switch to __KERNEL_CS after GDT is loaded
x86/boot: Fix -Wint-to-pointer-cast build warning
x86/boot: Add kstrtoul() from lib/
x86/tboot: Mark tboot static
x86/setup: Add an initrdmem= option to specify initrd physical address
- Add AMD Fam17h RAPL support
- Introduce CAP_PERFMON to kernel and user space
- Add Zhaoxin CPU support
- Misc fixes and cleanups
Tooling changes:
perf record:
- Introduce --switch-output-event to use arbitrary events to be setup
and read from a side band thread and, when they take place a signal
be sent to the main 'perf record' thread, reusing the --switch-output
code to take perf.data snapshots from the --overwrite ring buffer, e.g.:
# perf record --overwrite -e sched:* \
--switch-output-event syscalls:*connect* \
workload
will take perf.data.YYYYMMDDHHMMSS snapshots up to around the
connect syscalls.
- Add --num-synthesize-threads option to control degree of parallelism of the
synthesize_mmap() code which is scanning /proc/PID/task/PID/maps and can be
time consuming. This mimics pre-existing behaviour in 'perf top'.
perf bench:
- Add a multi-threaded synthesize benchmark.
- Add kallsyms parsing benchmark.
Intel PT support:
- Stitch LBR records from multiple samples to get deeper backtraces,
there are caveats, see the csets for details.
- Allow using Intel PT to synthesize callchains for regular events.
- Add support for synthesizing branch stacks for regular events (cycles,
instructions, etc) from Intel PT data.
Misc changes:
- Updated perf vendor events for power9 and Coresight.
- Add flamegraph.py script via 'perf flamegraph'
- Misc other changes, fixes and cleanups - see the Git log for details.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=i27M
-----END PGP SIGNATURE-----
Merge tag 'perf-core-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Add AMD Fam17h RAPL support
- Introduce CAP_PERFMON to kernel and user space
- Add Zhaoxin CPU support
- Misc fixes and cleanups
Tooling changes:
- perf record:
Introduce '--switch-output-event' to use arbitrary events to be
setup and read from a side band thread and, when they take place a
signal be sent to the main 'perf record' thread, reusing the core
for '--switch-output' to take perf.data snapshots from the ring
buffer used for '--overwrite', e.g.:
# perf record --overwrite -e sched:* \
--switch-output-event syscalls:*connect* \
workload
will take perf.data.YYYYMMDDHHMMSS snapshots up to around the
connect syscalls.
Add '--num-synthesize-threads' option to control degree of
parallelism of the synthesize_mmap() code which is scanning
/proc/PID/task/PID/maps and can be time consuming. This mimics
pre-existing behaviour in 'perf top'.
- perf bench:
Add a multi-threaded synthesize benchmark and kallsyms parsing
benchmark.
- Intel PT support:
Stitch LBR records from multiple samples to get deeper backtraces,
there are caveats, see the csets for details.
Allow using Intel PT to synthesize callchains for regular events.
Add support for synthesizing branch stacks for regular events
(cycles, instructions, etc) from Intel PT data.
Misc changes:
- Updated perf vendor events for power9 and Coresight.
- Add flamegraph.py script via 'perf flamegraph'
- Misc other changes, fixes and cleanups - see the Git log for details
Also, since over the last couple of years perf tooling has matured and
decoupled from the kernel perf changes to a large degree, going
forward Arnaldo is going to send perf tooling changes via direct pull
requests"
* tag 'perf-core-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (163 commits)
perf/x86/rapl: Add AMD Fam17h RAPL support
perf/x86/rapl: Make perf_probe_msr() more robust and flexible
perf/x86/rapl: Flip logic on default events visibility
perf/x86/rapl: Refactor to share the RAPL code between Intel and AMD CPUs
perf/x86/rapl: Move RAPL support to common x86 code
perf/core: Replace zero-length array with flexible-array
perf/x86: Replace zero-length array with flexible-array
perf/x86/intel: Add more available bits for OFFCORE_RESPONSE of Intel Tremont
perf/x86/rapl: Add Ice Lake RAPL support
perf flamegraph: Use /bin/bash for report and record scripts
perf cs-etm: Move definition of 'traceid_list' global variable from header file
libsymbols kallsyms: Move hex2u64 out of header
libsymbols kallsyms: Parse using io api
perf bench: Add kallsyms parsing
perf: cs-etm: Update to build with latest opencsd version.
perf symbol: Fix kernel symbol address display
perf inject: Rename perf_evsel__*() operating on 'struct evsel *' to evsel__*()
perf annotate: Rename perf_evsel__*() operating on 'struct evsel *' to evsel__*()
perf trace: Rename perf_evsel__*() operating on 'struct evsel *' to evsel__*()
perf script: Rename perf_evsel__*() operating on 'struct evsel *' to evsel__*()
...
- RCU-tasks update, including addition of RCU Tasks Trace for
BPF use and TASKS_RUDE_RCU
- kfree_rcu() updates.
- Remove scheduler locking restriction
- RCU CPU stall warning updates.
- Torture-test updates.
- Miscellaneous fixes and other updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Yisx
-----END PGP SIGNATURE-----
Merge tag 'core-rcu-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
"The RCU updates for this cycle were:
- RCU-tasks update, including addition of RCU Tasks Trace for BPF use
and TASKS_RUDE_RCU
- kfree_rcu() updates.
- Remove scheduler locking restriction
- RCU CPU stall warning updates.
- Torture-test updates.
- Miscellaneous fixes and other updates"
* tag 'core-rcu-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
rcu: Allow for smp_call_function() running callbacks from idle
rcu: Provide rcu_irq_exit_check_preempt()
rcu: Abstract out rcu_irq_enter_check_tick() from rcu_nmi_enter()
rcu: Provide __rcu_is_watching()
rcu: Provide rcu_irq_exit_preempt()
rcu: Make RCU IRQ enter/exit functions rely on in_nmi()
rcu/tree: Mark the idle relevant functions noinstr
x86: Replace ist_enter() with nmi_enter()
x86/mce: Send #MC singal from task work
x86/entry: Get rid of ist_begin/end_non_atomic()
sched,rcu,tracing: Avoid tracing before in_nmi() is correct
sh/ftrace: Move arch_ftrace_nmi_{enter,exit} into nmi exception
lockdep: Always inline lockdep_{off,on}()
hardirq/nmi: Allow nested nmi_enter()
arm64: Prepare arch_nmi_enter() for recursion
printk: Disallow instrumenting print_nmi_enter()
printk: Prepare for nested printk_nmi_enter()
rcutorture: Convert ULONG_CMP_LT() to time_before()
torture: Add a --kasan argument
torture: Save a few lines by using config_override_param initially
...
- refactor pstore locking for safer module unloading (Kees Cook)
- remove orphaned records from pstorefs when backend unloaded (Kees Cook)
- refactor dump_oops parameter into max_reason (Pavel Tatashin)
- introduce pstore/zone for common code for contiguous storage (WeiXiong Liao)
- introduce pstore/blk for block device backend (WeiXiong Liao)
- introduce mtd backend (WeiXiong Liao)
-----BEGIN PGP SIGNATURE-----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=7s1u
-----END PGP SIGNATURE-----
Merge tag 'pstore-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"Fixes and new features for pstore.
This is a pretty big set of changes (relative to past pstore pulls),
but it has been in -next for a while. The biggest change here is the
ability to support a block device as a pstore backend, which has been
desired for a while. A lot of additional fixes and refactorings are
also included, mostly in support of the new features.
- refactor pstore locking for safer module unloading (Kees Cook)
- remove orphaned records from pstorefs when backend unloaded (Kees
Cook)
- refactor dump_oops parameter into max_reason (Pavel Tatashin)
- introduce pstore/zone for common code for contiguous storage
(WeiXiong Liao)
- introduce pstore/blk for block device backend (WeiXiong Liao)
- introduce mtd backend (WeiXiong Liao)"
* tag 'pstore-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (35 commits)
mtd: Support kmsg dumper based on pstore/blk
pstore/blk: Introduce "best_effort" mode
pstore/blk: Support non-block storage devices
pstore/blk: Provide way to query pstore configuration
pstore/zone: Provide way to skip "broken" zone for MTD devices
Documentation: Add details for pstore/blk
pstore/zone,blk: Add ftrace frontend support
pstore/zone,blk: Add console frontend support
pstore/zone,blk: Add support for pmsg frontend
pstore/blk: Introduce backend for block devices
pstore/zone: Introduce common layer to manage storage zones
ramoops: Add "max-reason" optional field to ramoops DT node
pstore/ram: Introduce max_reason and convert dump_oops
pstore/platform: Pass max_reason to kmesg dump
printk: Introduce kmsg_dump_reason_str()
printk: honor the max_reason field in kmsg_dumper
printk: Collapse shutdown types into a single dump reason
pstore/ftrace: Provide ftrace log merging routine
pstore/ram: Refactor ftrace buffer merging
pstore/ram: Refactor DT size parsing
...
* pm-cpuidle:
cpuidle: Fix three reference count leaks
cpuidle: Convert Qualcomm SPM driver to a generic CPUidle driver
Documentation: ABI: make current_governer_ro as a candidate for removal
Documentation: cpuidle: update the document
cpuidle: sysfs: Remove sysfs_switch and switch attributes
cpuidle: Make cpuidle governor switchable to be the default behaviour
cpuidle: sysfs: Accept governor name with 15 characters
cpuidle: sysfs: Fix the overlap for showing available governors
cpuidle: psci: Fixup execution order when entering a domain idle state
cpuidle: sysfs: Minor coding style corrections
cpuidle: sysfs: Remove the unused define_one_r(o/w) macros
This introduces mtdpstore, which is similar to mtdoops but more
powerful. It uses pstore/blk, and aims to store panic and oops logs to
a flash partition, where pstore can later read back and present as files
in the mounted pstore filesystem.
To make mtdpstore work, the "blkdev" of pstore/blk should be set
as MTD device name or MTD device number. For more details, see
Documentation/admin-guide/pstore-blk.rst
This solves a number of issues:
- Work duplication: both of pstore and mtdoops do the same job storing
panic/oops log. They have very similar logic, registering to kmsg
dumper and storing logs to several chunks one by one.
- Layer violations: drivers should provides methods instead of polices.
MTD should provide read/write/erase operations, and allow a higher
level drivers to provide the chunk management, kmsg dump
configuration, etc.
- Missing features: pstore provides many additional features, including
presenting the logs as files, logging dump time and count, and
supporting other frontends like pmsg, console, etc.
Signed-off-by: WeiXiong Liao <liaoweixiong@allwinnertech.com>
Link: https://lore.kernel.org/lkml/20200511233229.27745-11-keescook@chromium.org/
Link: https://lore.kernel.org/r/1589266715-4168-1-git-send-email-liaoweixiong@allwinnertech.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Add support for non-block devices (e.g. MTD). A non-block driver calls
pstore_blk_register_device() to register iself.
In addition, pstore/zone is updated to handle non-block devices,
where an erase must be done before a write. Without this, there is no
way to remove records stored to an MTD.
Signed-off-by: WeiXiong Liao <liaoweixiong@allwinnertech.com>
Link: https://lore.kernel.org/lkml/20200511233229.27745-10-keescook@chromium.org/
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Add details on using pstore/blk, the new backend of pstore to record
dumps to block devices, in Documentation/admin-guide/pstore-blk.rst
Signed-off-by: WeiXiong Liao <liaoweixiong@allwinnertech.com>
Link: https://lore.kernel.org/lkml/20200511233229.27745-7-keescook@chromium.org/
Signed-off-by: Kees Cook <keescook@chromium.org>
Now that pstore_register() can correctly pass max_reason to the kmesg
dump facility, introduce a new "max_reason" module parameter and
"max-reason" Device Tree field.
The "dump_oops" module parameter and "dump-oops" Device
Tree field are now considered deprecated, but are now automatically
converted to their corresponding max_reason values when present, though
the new max_reason setting has precedence.
For struct ramoops_platform_data, the "dump_oops" member is entirely
replaced by a new "max_reason" member, with the only existing user
updated in place.
Additionally remove the "reason" filter logic from ramoops_pstore_write(),
as that is not specifically needed anymore, though technically
this is a change in behavior for any ramoops users also setting the
printk.always_kmsg_dump boot param, which will cause ramoops to behave as
if max_reason was set to KMSG_DUMP_MAX.
Co-developed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Link: https://lore.kernel.org/lkml/20200515184434.8470-6-keescook@chromium.org/
Signed-off-by: Kees Cook <keescook@chromium.org>
Currently, the root cgroup does not have a cpu.stat file. Add one which
is consistent with /proc/stat to capture global cpu statistics that
might not fall under cgroup accounting.
We haven't done this in the past because the data are already presented
in /proc/stat and we didn't want to add overhead from collecting root
cgroup stats when cgroups are configured, but no cgroups have been
created.
By keeping the data consistent with /proc/stat, I think we avoid the
first problem, while improving the usability of cgroups stats.
We avoid the second problem by computing the contents of cpu.stat from
existing data collected for /proc/stat anyway.
Signed-off-by: Boris Burkov <boris@bur.io>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This documents ignore-unaligned-usertrap, unaligned-dump-stack, and
unaligned-trap, based on arch/arc/kernel/unaligned.c,
arch/ia64/kernel/unaligned.c, and arch/parisc/kernel/unaligned.c.
While we're at it, integrate unaligned-memory-access.txt into the docs
tree.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200515212443.5012-1-steve@sk2.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Update Documentation/admin-guide/bug-hunting.rst:
- add a small section on "Modules linked in" and their possible flags;
- delete all references to ksymoops since it is no longer applicable;
- fix spello, grammar, and punctuation;
- note that get_maintainers.pl only provides recent patchers if it is
run inside a git tree;
- add mention of scripts/decode_stacktrace.sh;
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: greg@wind.rmcc.com
Link: https://lore.kernel.org/r/c629a9ef-3867-c3d1-f6c9-2c3b0e4ac68a@infradead.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Changing base clock frequency directly impacts TSC Hz but not CPUID.16h
value. An overclocked CPU supporting CPUID.16h and with partial CPUID.15h
support will set TSC KHZ according to "best guess" given by CPUID.16h
relying on tsc_refine_calibration_work to give better numbers later.
tsc_refine_calibration_work will refuse to do its work when the outcome is
off the early TSC KHZ value by more than 1% which is certain to happen on
an overclocked system.
Fix this by adding a tsc_early_khz command line parameter that makes the
kernel skip early TSC calibration and use the given value instead.
This allows the user to provide the expected TSC frequency that is closer
to reality than the one reported by the hardware, enabling
tsc_refine_calibration_work to do meaningful error checking.
[ tglx: Made the variable __initdata as it's only used on init and
removed the error checking in the argument parser because
kstrto*() only stores to the variable if the string is valid ]
Signed-off-by: Krzysztof Piecuch <piecuch@protonmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/O2CpIOrqLZHgNRkfjRpz_LGqnc1ix_seNIiOCvHY4RHoulOVRo6kMXKuLOfBVTi0SMMevg6Go1uZ_cL9fLYtYdTRNH78ChaFaZyG3VAyYz8=@protonmail.com
Implement handling for metadata version 2. The new metadata adds a
label and UUID for the device mapper device, and additional UUID for
the underlying block devices.
It also allows for an additional regular drive to be used for
emulating random access zones. The emulated zones will be placed
logically in front of the zones from the zoned block device, causing
the superblocks and metadata to be stored on that device.
The first zone of the original zoned device will be used to hold
another, tertiary copy of the metadata; this copy carries a generation
number of 0 and is never updated; it's just used for identification.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This option increases the number of SLB misses by limiting the number
of kernel SLB entries, and increased flushing of cached lookaside
information. This helps stress test difficult to hit paths in the
kernel.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Relocate the code into arch/powerpc/mm, s/torture/stress/]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200511125825.3081305-1-mpe@ellerman.id.au
Added documentation to configure servers to use Intel(R) Speed
Select Technology using intel-speed-select tool.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Andriy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update the document after the remove of cpuidle_sysfs_switch.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 2f4c33063a.
The changes here were fine, but there's a non-documentation change to
sysctl.c that makes messes elsewhere; those changes should have been done
independently.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The goal is to be able to inherit the initial devconf parameters from the
current netns, ie the netns where this new netns has been created.
This is useful in a containers environment where /proc/sys is read only.
For example, if a pod is created with specifics devconf parameters and has
the capability to create netns, the user expects to get the same parameters
than his 'init_net', which is not the real init_net in this case.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 4 IRQ documentation files under Documentation/*.txt.
Move them into a new directory (core-api/irq) and add a new
index file for it.
While here, use a title markup for the Debugging section of the
irq-domain.rst file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/2da7485c3718e1442e6b4c2dd66857b776e8899b.1588345503.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There is an special chapter inside the core-api book about
some debug infrastructure like tracepoints and debug objects.
It sounded to me that this is the best place to add a chapter
explaining how to use a FireWire controller to do remote
kernel debugging, as explained on this document.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/9b489d36d08ad89d3ad5aefef1f52a0715b29716.1588345503.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Make some miscellaneous fixes to the first paragraph of "ECC memory":
- Change the incorrect "74 bits" to "72 bits".
- Change "mentioned on" to "mentioned in".
- Remove the extra "extra".
- Rephrase some sentences as suggested by Matthew Wilcox.
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lore.kernel.org/r/20200506162217.16633-1-longman@redhat.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
During recent patch discussion [1] it became apparent that the "other_node"
definition in the numastat documentation has always been different from actual
implementation. It was also noted that the stats can be innacurate on systems
with memoryless nodes.
This patch corrects the other_node definition (with minor tweaks to two more
definitions), adds a note about memoryless nodes and also two introductory
paragraphs to the numastat documentation.
[1] https://lore.kernel.org/linux-mm/20200504070304.127361-1-sandipan@linux.ibm.com/T/#u
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Sandipan Das <sandipan@linux.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Link: https://lore.kernel.org/r/20200507120217.12313-1-vbabka@suse.cz
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This is a read-only export of NGROUPS_MAX, so this patch also changes
the declarations in kernel/sysctl.c to const.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20200515160222.7994-1-steve@sk2.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add callback for 'dmsetup message' to allow the reclaim process
to be triggered manually.
Eg.
dmsetup message /dev/dm-X 0 message
will start the reclaim process even if the default threshold
of 50 percent of free random zones is not reached.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add callback to supply information for 'dmsetup status'
and 'dmsetup table'. The output for 'dmsetup status' is
0 <size> zoned <nr_zones> zones <nr_unmap_rnd>/<nr_rnd> random <nr_unmap_seq>/<nr_seq> sequential
where <nr_unmap_rnd> is the number of unmapped (ie free) random zones,
<nr_rnd> the total number of random zones, <nr_unmap_seq> the number
of unmapped sequential zones, and <nr_seq> the total number of
sequential zones.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This new target is similar to the linear target except that it emulates
a smaller logical block size on a device with a larger logical block
size. Its main purpose is to emulate 512 byte sectors on 4K native
disks (i.e. 512e).
See Documentation/admin-guide/device-mapper/dm-ebs.rst for details.
Reviewed-by: Damien Le Moal <DamienLeMoal@wdc.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> [Kconfig fixes]
Signed-off-by: Zheng Bin <zhengbin13@huawei.com> [static fixes]
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The user is not supposed to thinker with the underlying sysrq_key_op.
Make that explicit by adding a handful of const notations.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://lore.kernel.org/r/20200513214351.2138580-2-emil.l.velikov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes it is useful to preserve batches of configs when making
localmodconfig. For example, I usually don't want any usb and fs
modules to be disabled. Now we can do it by:
$ make LMC_KEEP="drivers/usb:fs" localmodconfig
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Add documentation for KERNELPACMASK variable being added to the vmcoreinfo.
It indicates the PAC bits mask information of signed kernel pointers if
Armv8.3-A Pointer Authentication feature is present.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Link: https://lore.kernel.org/r/1589202116-18265-2-git-send-email-amit.kachhap@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
fixes.2020.04.27a: Miscellaneous fixes.
kfree_rcu.2020.04.27a: Changes related to kfree_rcu().
rcu-tasks.2020.04.27a: Addition of new RCU-tasks flavors.
stall.2020.04.27a: RCU CPU stall-warning updates.
torture.2020.05.07a: Torture-test updates.
This commit provides an rcutorture.stall_gp_kthread module parameter
to allow rcutorture to starve the grace-period kthread. This allows
testing the code that detects such starvation.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
This commit aids testing of RCU task stall warning messages by adding
an rcutorture.stall_cpu_block module parameter that results in the
induced stall sleeping within the RCU read-side critical section.
Spinning with interrupts disabled is still available via the
rcutorture.stall_cpu_irqsoff module parameter, and specifying neither
of these two module parameters will spin with preemption disabled.
Note that sleeping (as opposed to preemption) results in additional
complaints from RCU at context-switch time, so yet more testing.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Sphinx 2.4.4 produces this warning:
Documentation/admin-guide/media/ipu3.rst:235: WARNING: Title underline too short.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Based on the firmware fallback mechanisms documentation and the
implementation in drivers/base/firmware_loader/fallback.c.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200429205757.8677-2-steve@sk2.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Based on the ftrace documentation, the tp_printk boot parameter
documentation, and the implementation in kernel/trace/trace.c.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20200429205757.8677-1-steve@sk2.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
After adding all cardlists, this file became too big. Split
it on smaller files, in order to make easier to maintain.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On several parts of the document, it mentions "PCI ID", when
it is actually referring to the subsystem's part of the PCI
ID.
Change the language to let it be clear.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add some explanation of the ImgU running mode and add more information
about firmware selection and running mode usage.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
5.7 merge window.
- Fix potential for DM writecache data corruption during DM table
reloads.
- Fix DM verity's FEC support's hash block number calculation in
verity_fec_decode().
- Fix bio-based DM multipath crash due to use of stale copy of
MPATHF_QUEUE_IO flag state in __map_bio().
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEJfWUX4UqZ4x1O2wixSPxCi2dA1oFAl6rSn4THHNuaXR6ZXJA
cmVkaGF0LmNvbQAKCRDFI/EKLZ0DWjmFB/9kwi4L5SQTg81ak0jmiO4lNSxqvc8s
ZJUyT8m/Iheh6FWo6kZYyfN+YVPPwXRFDWk4TGSrKyoqElTbpxkkmVxE7nhp9Z+O
1f7cfD8vCsTexHxYjxx3DxW529YVjvccifhaJFQgCA3II8+0to9PFzc7v6JpFBGS
1CWd169OUDHe2XGNmah0lbgwEgb7ZQRn9MNrkdYu3L9HihNLs8h4uin390FlfhSj
+/rS89jkA9X5MhFnspKrX0wGl3qoQBzFFvvn4KKPcH8EPt5zsUPVo+/rTOBL8Tr8
VXDYKco4CDfuqzB5LdHeTi3mKwGq+fpPmwzRTk+/gosDZHA49m7mLKGB
=cr8K
-----END PGP SIGNATURE-----
Merge tag 'for-5.7/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Document DM integrity allow_discard feature that was added during 5.7
merge window.
- Fix potential for DM writecache data corruption during DM table
reloads.
- Fix DM verity's FEC support's hash block number calculation in
verity_fec_decode().
- Fix bio-based DM multipath crash due to use of stale copy of
MPATHF_QUEUE_IO flag state in __map_bio().
* tag 'for-5.7/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm multipath: use updated MPATHF_QUEUE_IO on mapping for bio-based mpath
dm verity fec: fix hash block number in verity_fec_decode
dm writecache: fix data corruption when reloading the target
dm integrity: document allow_discard option
- add SPDX header;
- add a document title;
- mark code blocks and literals as such;
- mark tables as such;
- add notes markups;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- add a document title;
- mark lists as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not much to be done here:
- add SPDX header;
- add a document title;
- mark a literal as such, in order to avoid a warning;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- mark lists as such;
- mark tables as such;
- use footnote markup;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark lists as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the implementation in kernel/sysctl.c (the proc_do_cad_pid()
function), kernel/reboot.c, and include/linux/sched/signal.h.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200423183651.15365-1-steve@sk2.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There are changes in the usage of PCI for the user:
- new kernel parameter
- modification of the way functions are enumerated
Let's document these.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This commit provides a rcupdate.rcu_task_ipi_delay kernel boot parameter
that specifies how old the RCU tasks trace grace period must be before
the grace-period kthread starts sending IPIs. This delay allows more
tasks to pass through rcu_tasks_qs() quiescent states, thus reducing
(or even eliminating) the number of IPIs that must be sent.
On a short rcutorture test setting this kernel boot parameter to HZ/2
resulted in zero IPIs for all 877 RCU-tasks trace grace periods that
elapsed during that test.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Add the initrdmem option:
initrdmem=ss[KMG],nn[KMG]
which is used to specify the physical address of the initrd, almost
always an address in FLASH. Also add code for x86 to use the existing
phys_init_start and phys_init_size variables in the kernel.
This is useful in cases where a kernel and an initrd is placed in FLASH,
but there is no firmware file system structure in the FLASH.
One such situation occurs when unused FLASH space on UEFI systems has
been reclaimed by, e.g., taking it from the Management Engine. For
example, on many systems, the ME is given half the FLASH part; not only
is 2.75M of an 8M part unused; but 10.75M of a 16M part is unused. This
space can be used to contain an initrd, but need to tell Linux where it
is.
This space is "raw": due to, e.g., UEFI limitations: it can not be added
to UEFI firmware volumes without rebuilding UEFI from source or writing
a UEFI device driver. It can be referenced only as a physical address
and size.
At the same time, if a kernel can be "netbooted" or loaded from GRUB or
syslinux, the option of not using the physical address specification
should be available.
Then, it is easy to boot the kernel and provide an initrd; or boot the
the kernel and let it use the initrd in FLASH. In practice, this has
proven to be very helpful when integrating Linux into FLASH on x86.
Hence, the most flexible and convenient path is to enable the initrdmem
command line option in a way that it is the last choice tried.
For example, on the DigitalLoggers Atomic Pi, an image into FLASH can be
burnt in with a built-in command line which includes:
initrdmem=0xff968000,0x200000
which specifies a location and size.
[ bp: Massage commit message, make it passive. ]
[akpm@linux-foundation.org: coding style fixes]
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Link: http://lkml.kernel.org/r/CAP6exYLK11rhreX=6QPyDQmW7wPHsKNEFtXE47pjx41xS6O7-A@mail.gmail.com
Link: https://lkml.kernel.org/r/20200426011021.1cskg0AGd%akpm@linux-foundation.org
Here are a number of USB driver fixes for 5.7-rc3.
Nothing huge, just the usual collection of:
- xhci fixes
- gadget driver fixes
- syzkaller fuzzing fixes
- new device ids and DT bindings
- new quirks added for broken devices
A few of the gadget driver fixes show up twice here as they were applied
to my branch, and also by Felipe to his branch which I then pulled in as
we got out of sync a bit.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXqVfog8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynVFwCfb33URz0KrXE+ipecpheVEoMdvDsAoIuYG4cb
qxLwEE6203jdICq9/nDg
=8f/s
-----END PGP SIGNATURE-----
Merge tag 'usb-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB driver fixes for 5.7-rc3.
Nothing huge, just the usual collection of:
- xhci fixes
- gadget driver fixes
- syzkaller fuzzing fixes
- new device ids and DT bindings
- new quirks added for broken devices
A few of the gadget driver fixes show up twice here as they were
applied to my branch, and also by Felipe to his branch which I then
pulled in as we got out of sync a bit.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
USB: sisusbvga: Change port variable from signed to unsigned
usb-storage: Add unusual_devs entry for JMicron JMS566
USB: hub: Revert commit bd0e6c9614 ("usb: hub: try old enumeration scheme first for high speed devices")
USB: hub: Fix handling of connect changes during sleep
usb: typec: altmode: Fix typec_altmode_get_partner sometimes returning an invalid pointer
xhci: Don't clear hub TT buffer on ep0 protocol stall
xhci: prevent bus suspend if a roothub port detected a over-current condition
xhci: Fix handling halted endpoint even if endpoint ring appears empty
usb: raw-gadget: Fix copy_to/from_user() checks
usb: raw-gadget: fix raw_event_queue_fetch locking
usb: gadget: udc: atmel: Fix vbus disconnect handling
usb: dwc3: gadget: Fix request completion check
USB: Add USB_QUIRK_DELAY_CTRL_MSG and USB_QUIRK_DELAY_INIT for Corsair K70 RGB RAPIDFIRE
phy: tegra: Select USB_COMMON for usb_get_maximum_speed()
usb: typec: tcpm: Ignore CC and vbus changes in PORT_RESET change
usb: f_fs: Clear OS Extended descriptor counts to zero in ffs_data_reset()
cdc-acm: introduce a cool down
cdc-acm: close race betrween suspend() and acm_softint
UAS: fix deadlock in error handling and PM flushing work
UAS: no use logging any details in case of ENODEV
...
Commit bd0e6c9614 ("usb: hub: try old enumeration scheme first for
high speed devices") changed the way the hub driver enumerates
high-speed devices. Instead of using the "new" enumeration scheme
first and switching to the "old" scheme if that doesn't work, we start
with the "old" scheme. In theory this is better because the "old"
scheme is slightly faster -- it involves resetting the device only
once instead of twice.
However, for a long time Windows used only the "new" scheme. Zeng Tao
said that Windows 8 and later use the "old" scheme for high-speed
devices, but apparently there are some devices that don't like it.
William Bader reports that the Ricoh webcam built into his Sony Vaio
laptop not only doesn't enumerate under the "old" scheme, it gets hung
up so badly that it won't then enumerate under the "new" scheme! Only
a cold reset will fix it.
Therefore we will revert the commit and go back to trying the "new"
scheme first for high-speed devices.
Reported-and-tested-by: William Bader <williambader@hotmail.com>
Ref: https://bugzilla.kernel.org/show_bug.cgi?id=207219
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: bd0e6c9614 ("usb: hub: try old enumeration scheme first for high speed devices")
CC: Zeng Tao <prime.zeng@hisilicon.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221611230.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernel + tools/perf:
Alexey Budankov:
- Introduce CAP_PERFMON to kernel and user space.
callchains:
Adrian Hunter:
- Allow using Intel PT to synthesize callchains for regular events.
Kan Liang:
- Stitch LBR records from multiple samples to get deeper backtraces,
there are caveats, see the csets for details.
perf script:
Andreas Gerstmayr:
- Add flamegraph.py script
BPF:
Jiri Olsa:
- Synthesize bpf_trampoline/dispatcher ksymbol events.
perf stat:
Arnaldo Carvalho de Melo:
- Honour --timeout for forked workloads.
Stephane Eranian:
- Force error in fallback on :k events, to avoid counting nothing when
the user asks for kernel events but is not allowed to.
perf bench:
Ian Rogers:
- Add event synthesis benchmark.
tools api fs:
Stephane Eranian:
- Make xxx__mountpoint() more scalable
libtraceevent:
He Zhe:
- Handle return value of asprintf.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCXp2LlQAKCRCyPKLppCJ+
J95oAP0ZihVUhESv/gdeX0IDE5g6Rd2V6LNcRj+jb7gX9NlQkwD/UfS454WV1ftQ
qTwrkKPzY/5Tm2cLuVE7r7fJ6naDHgU=
=FHm4
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-5.8-20200420' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core fixes and improvements from Arnaldo Carvalho de Melo:
kernel + tools/perf:
Alexey Budankov:
- Introduce CAP_PERFMON to kernel and user space.
callchains:
Adrian Hunter:
- Allow using Intel PT to synthesize callchains for regular events.
Kan Liang:
- Stitch LBR records from multiple samples to get deeper backtraces,
there are caveats, see the csets for details.
perf script:
Andreas Gerstmayr:
- Add flamegraph.py script
BPF:
Jiri Olsa:
- Synthesize bpf_trampoline/dispatcher ksymbol events.
perf stat:
Arnaldo Carvalho de Melo:
- Honour --timeout for forked workloads.
Stephane Eranian:
- Force error in fallback on :k events, to avoid counting nothing when
the user asks for kernel events but is not allowed to.
perf bench:
Ian Rogers:
- Add event synthesis benchmark.
tools api fs:
Stephane Eranian:
- Make xxx__mountpoint() more scalable
libtraceevent:
He Zhe:
- Handle return value of asprintf.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to better organize the main admin-guide index,
place the driver-specific indexes on separate files.
This ensures a more consistent numbering at the main index.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Separate the generic documentation from the driver-specific
parts, and use a better title for the documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The old cards.rst file doesn't exist anymore. Also, it is not
the right reference there, as it should be pointing to the
bttv-specific cardlist.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While test drivers is probably something that normal users
won't bother, it doesn't hurt to add them to the card list.
This way, all drivers, except for the ones under staging,
would be listed there.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The SPI cards are also under the concept of "platform" drivers
as defined at the section introduction.
So, add a SPI card list there.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Having a table with a list of all USB drivers seems worth,
and it comes almost for free, as we can just use Kconfig
descriptions (with some adjustments).
So, add a table for that.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of listing "other" PCI card list, just add a list with
the existing drivers (not including sub-drivers).
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The frontend drivers list is incomplete. Update it from
what's there at the Kernel Kconfig files.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The DVB cards.rst file is old and outdated. It also contains
data that are contained on other cardlists. Remove the
duplicated information and split frontends and PCI cards on
separate files.
As all USB cards already have their own card lists, just drop
the old USB data there.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several other USB cards. Most of them support just
one device. The only exception is the "pwc" driver. But, as
updates to it are not frequent, let's just place everything
manually into a single file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The siano driver looks like em28xx, except that its cards
are split on 3 drivers.
Add a card list for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cardlist section is important for some boards, because they
may require extra modprobe parameters.
Improve the docs to mention that.
Thanks-to: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for providing me some PCI IDs
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Several of the existing documents under the media admin-guide
contain build procedures.
Add an specific chapter describing it. This document was
partially inspired on the modifications I made to the bttv.rst
file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media's admin guide is currently just a group of
not-connected docs.
Add an introduction chapter for it to start making sense
to a random reader.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It is interesting to have a card list also for cx231xx
driver, as it currently supports 27 different boards.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Improve the documentation by providing examples on how to test camera
capture on imx6q-sabresd via v4l2-ctl and Gstreamer.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Steve Longerbeam<slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to improve the documentation, provide the OV5640 MIPI module
part number that is used on the imx6q-sabresd board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current example for imx6q-sabresd is for a direct conversion pipeline.
Provide an extra example using unprocessed video capture for completeness.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current instructions for imx6q-sabresd do not lead to functional
capture on OV5640 MIPI CSI-2.
The reason for this, as explained by Steve Longerbeam, is that OV5640 by
default transmits on virtual channel 0, not channel 1 as is given in the
instructions.
Adapt the instructions to use virtual channel 0 so that a working
camera setup can be achieved on imx6q-sabresd.
Also, since we are using an IC direct conversion pipeline, improve
the example by demonstrating colorspace and scaling.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Steve Longerbeam<slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Changes to make the text more formal and organized. The reasons are now cited and described at the same time.
Minor grammatical problems have also been fixed.
Signed-off-by: Cristian Souza <cristianmsbr@gmail.com>
Link: https://lore.kernel.org/r/20200411010201.GA22706@darkstar
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Based on the implementation in kernel/bpf/syscall.c,
kernel/bpf/trampoline.c, include/linux/filter.h, and the documentation
in bpftool-prog.rst.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200315122648.20558-1-steve@sk2.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Several parts of this document define literals: ioctl names,
function calls, directory patches, etc. Mark those as literal
blocks, in order to improve its readability (both at text mode
and after parsed by Sphinx.
This fixes those two warnings:
Documentation/admin-guide/mm/userfaultfd.rst:139: WARNING: Inline emphasis start-string without end-string.
Documentation/admin-guide/mm/userfaultfd.rst:139: WARNING: Inline emphasis start-string without end-string.
produced during documentation build.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/2ae061761baf8fe00cdf8a7e6dae293756849a05.1586881715.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Sphinx produce some warnings due to a bad table format:
Documentation/admin-guide/ras.rst:358: WARNING: Definition list ends without a blank line; unexpected unindent.
Documentation/admin-guide/ras.rst:358: WARNING: Definition list ends without a blank line; unexpected unindent.
Documentation/admin-guide/ras.rst:363: WARNING: Definition list ends without a blank line; unexpected unindent.
Documentation/admin-guide/ras.rst:363: WARNING: Definition list ends without a blank line; unexpected unindent.
Rearrange the things there in order to supress the warnings
while being precise at the Sphinx output about how ranks are
mapped into csrows.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/9e1bb44d6dbedb5b6f049d081b47da1f9620de16.1586881715.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl6cxDAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGb2YH/3V3yrWOgbZkEWvO
IwW5nSjYk+xTBs7Tf5+nycWHpr+e92tX4m/+DZ6qn1sQpjdKEA7EZ/E0mpm0fm5w
Po+dzy4PP40CLi/Z0mXl3U3FWmp5l50Q4tEs5fzI6rQPKjX+G5qO8+J7Yu1iNduJ
KRbNeKCnUGHf2mRYiOJRNurVm4Yv370AIyvulxX5FkZHN7hTq/Js76sRV1BSnG7k
o1Vs4vvFSSdFgVxyuflpV0Uv9bDTxppqiwQ4ktntB8TKmVtXLT25wcO4V5LwRjQt
6o064j343Q+OQ4t/LZVKYUB0Fmw8Ks1YH00OOdH6G41wY6LogaxYIXM1YvUZ4NwQ
HjNsASY=
=kvEN
-----END PGP SIGNATURE-----
Merge tag 'v5.7-rc2' into patchwork
Linux 5.7-rc2
* tag 'v5.7-rc2': (331 commits)
Linux 5.7-rc2
mm: Fix MREMAP_DONTUNMAP accounting on VMA merge
xattr.h: Replace zero-length array with flexible-array member
uapi: linux: fiemap.h: Replace zero-length array with flexible-array member
uapi: linux: dlm_device.h: Replace zero-length array with flexible-array member
tpm_eventlog.h: Replace zero-length array with flexible-array member
ti_wilink_st.h: Replace zero-length array with flexible-array member
swap.h: Replace zero-length array with flexible-array member
skbuff.h: Replace zero-length array with flexible-array member
sched: topology.h: Replace zero-length array with flexible-array member
rslib.h: Replace zero-length array with flexible-array member
rio.h: Replace zero-length array with flexible-array member
posix_acl.h: Replace zero-length array with flexible-array member
platform_data: wilco-ec.h: Replace zero-length array with flexible-array member
memcontrol.h: Replace zero-length array with flexible-array member
list_lru.h: Replace zero-length array with flexible-array member
lib: cpu_rmap: Replace zero-length array with flexible-array member
irq.h: Replace zero-length array with flexible-array member
ihex.h: Replace zero-length array with flexible-array member
igmp.h: Replace zero-length array with flexible-array member
...
SRBDS is an MDS-like speculative side channel that can leak bits from the
random number generator (RNG) across cores and threads. New microcode
serializes the processor access during the execution of RDRAND and
RDSEED. This ensures that the shared buffer is overwritten before it is
released for reuse.
While it is present on all affected CPU models, the microcode mitigation
is not needed on models that enumerate ARCH_CAPABILITIES[MDS_NO] in the
cases where TSX is not supported or has been disabled with TSX_CTRL.
The mitigation is activated by default on affected processors and it
increases latency for RDRAND and RDSEED instructions. Among other
effects this will reduce throughput from /dev/urandom.
* Enable administrator to configure the mitigation off when desired using
either mitigations=off or srbds=off.
* Export vulnerability status via sysfs
* Rename file-scoped macros to apply for non-whitelist table initializations.
[ bp: Massage,
- s/VULNBL_INTEL_STEPPING/VULNBL_INTEL_STEPPINGS/g,
- do not read arch cap MSR a second time in tsx_fused_off() - just pass it in,
- flip check in cpu_set_bug_bits() to save an indentation level,
- reflow comments.
jpoimboe: s/Mitigated/Mitigation/ in user-visible strings
tglx: Dropped the fused off magic for now
]
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Neelima Krishnan <neelima.krishnan@intel.com>
After recent changes allowing scale-invariant utilization to be
used on x86, the schedutil governor on top of intel_pstate in the
passive mode should be on par with (or better than) the active mode
"powersave" algorithm of intel_pstate on systems in which
hardware-managed P-states (HWP) are not used, so it should not be
necessary to use the internal scaling algorithm in those cases.
Accordingly, modify intel_pstate to start in the passive mode by
default if the processor at hand does not support HWP of if the driver
is requested to avoid using HWP through the kernel command line.
Among other things, that will allow utilization clamps and the
support for RT/DL tasks in the schedutil governor to be utilized on
systems in which intel_pstate is used.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update the kernel.rst documentation file with the information related to
usage of CAP_PERFMON capability to secure performance monitoring and
observability operations in system.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Igor Lubashev <ilubashe@akamai.com>
Cc: James Morris <jmorris@namei.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Serge Hallyn <serge@hallyn.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-doc@vger.kernel.org
Cc: linux-man@vger.kernel.org
Cc: linux-security-module@vger.kernel.org
Cc: selinux@vger.kernel.org
Link: http://lore.kernel.org/lkml/84c32383-14a2-fa35-16b6-f9e59bd37240@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Update perf-security.rst documentation file with the information
related to usage of CAP_PERFMON capability to secure performance
monitoring and observability operations in system.
Committer notes:
While testing 'perf top' under cap_perfmon I noticed that it needs
some more capability and Alexey pointed out cap_ipc_lock, as needed by
this kernel chunk:
kernel/events/core.c: 6101
if ((locked > lock_limit) && perf_is_paranoid() &&
!capable(CAP_IPC_LOCK)) {
ret = -EPERM;
goto unlock;
}
So I added it to the documentation, and also mentioned that if the
libcap version doesn't yet supports 'cap_perfmon', its numeric value can
be used instead, i.e. if:
# setcap "cap_perfmon,cap_ipc_lock,cap_sys_ptrace,cap_syslog=ep" perf
Fails, try:
# setcap "38,cap_ipc_lock,cap_sys_ptrace,cap_syslog=ep" perf
I also added a paragraph stating that using an unpatched libcap will
fail the check for CAP_PERFMON, as it checks the cap number against a
maximum to see if it is valid, which makes it use as the default the
'cycles:u' event, even tho a cap_perfmon capable perf binary can get
kernel samples, to workaround that just use, e.g.:
# perf top -e cycles
# perf record -e cycles
And it will sample kernel and user modes.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Igor Lubashev <ilubashe@akamai.com>
Cc: James Morris <jmorris@namei.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Serge Hallyn <serge@hallyn.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-doc@vger.kernel.org
Cc: linux-man@vger.kernel.org
Cc: linux-security-module@vger.kernel.org
Cc: selinux@vger.kernel.org
Link: http://lore.kernel.org/lkml/17278551-9399-9ebe-d665-8827016a217d@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Documentation for the kernel.modprobe sysctl was added both by
commit 0317c5371e ("docs: merge debugging-modules.txt into
sysctl/kernel.rst") and by commit 6e71582506 ("docs: admin-guide:
document the kernel.modprobe sysctl"), resulting in the same sysctl
being documented in two places. Merge these into one place.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200414172430.230293-1-ebiggers@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
In order to make easier for people to navigate between the
three media guides, add cross-references between them
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Kranthi Kuntala