Extended BSG to support stats, port log and trace reset and to support
adapter, port SET operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added logic to check the loopback test input speed based on port mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to always acknowledge RME interrupt and update
consumer index (CI) when RME interrupt is generated.
- Made changes to have ASIC specific hw_rspq_ack() handler.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support to post vendor unique events on fc_host.
- Supports adapter, port, ioc, flash and remote port based AEN events.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added a new module parameter max_xfer_size to
set the max_sectors in the scsi_host template.
- Added logic to handle request_irq() failure so
that msix vector resource is de-allocated immediately
when failure happens.
- BSG enhancements to collect vHBA releated info and port log.
- Removed the workaround of incrementing the module refcnt on bsg request.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added PHY sub-module.
- Implemented interface to obtain stats and to
read/update the fw from the PHY module.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added diagnostics sub-module to BFA.
- Implemented interface to perform memtest/loopback test
and some other diagnostics tests.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added SFP sub-module to BFA.
- Added interface to collect sfp media info and sfp speed.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added CEE sub-module.
- Added support to collect stats/cee module info
using BSG interface.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support to collect driver/fw stats.
- Added support to perform adapter/ioc enable, disable operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added logic to initiate a PLOGI to the target, while processing a LOGO
from the same target in Direct attach mode.
- Added logic to generate a FCCT Reject indicating unsupported command,
upon receiving FCCT/FCGS requests.
- Added logic to set the fcpim in offline state and avoid any PRLI retries
if a PRLI response is a reject with a reason Command Not Supported.
- Updated the FDMI Supported/Current speeds.
- Added logic to wait for the response from the firmware before sending
ACC to PLOGI and transitioning to subsequent states - while processing an
Incoming PLOGI in online state.
- Added a wait state in the fcs_vport state machine - For case where
FDISC is in progress and we get a vport delete request we wait for
fdisc response and will transition to the appropriate state based on
rsp status, else its causing both driver/fw resources to be not
freed.
- Remove the fc_credit_recovery module param.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Modified the design such that each BFA sub-module will provide
the amount of DMA and KVA memory needed by it and queues the
same request to the global dma and kva info queues.
- During the memory allocation we iterate over this queue to allocate
the dma and kva memory requested by sub-modules.
- The change is needed to avoid requesting the aggregate amount of memory
needed by all the BFA sub-modules as one contiguous chunk.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Introduced partitioning of the BFA resources.
- Added h/w queue ID in CPE messages, firmware uses h/w queue ID
from messages to pick a matching RME queue.
- Added message header to bfa_reqq_produce(). h/w queue ID is set
in the message header and firmware modules use h/w queue ID from
message header instead of from cpqe event.
- Made changes to allow using all 256 queues of Brocade-1860 asic.
Previously only a single queue per queue group was used.
- Added function tag to BFI message header. Only used by FC BFI
messages. Used to translate host tag to firmware tag. bfa_lpuid()
is changed to bfa_fn_lpu() that encodes both PCI function and port
ID in BFI message header.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- If flash controller is halted unconditionally, this results in
illegal write access to flash controller register domain. Since
flash controller registers are only accessible once s_clk is started
- added logic to check for WGN status and halt flash controller only
if it is already running.
- Added check to wait for flash controller halt to be completed before
proceeding with s_clk/l_clk initializations.
- Removed unnecessary reset logic for PMM 1T memory and moved memory
initialization after flash access enable.
- Disable Brocade-1860 asic MBOX interrupt before PLL initialization.
- Remove reset enable for S_CLK/L_CLK after both PLL initializations
are complete.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Updated/added data structures and definitions to support FAA protocol.
- Modified the IOC state machine to support FAA.
- Introduced FAA feature configuration - enable/disable/query.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Add logic to handle the case where PCI mapping goes away when
IOCPF state machine is waiting for semaphore.
- Added logic to unlock hw semaphore if the previos FW boot was
from flash based and the current FW initialization attempt is from OS.
- Added fix to update hbfails and hb_count stats during hwerror event.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added ASIC block configuration APIs:
- to create/delete/update the physical functions
- to do adapter/port mode configuration
- to query the current ASIC block configuration.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added BSG interface support to BFA driver
- Adds support to send ELS/CT FC passthru commands and
few vendor specific BSG requests.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Moved FCS initialization, which internally does the im_port creation
as well as the scsi_host creation before bfa_init.
Once the bfa_init is complete & successful:
- Reset the FCS base port cfg params such as pwwn/nwwn and setup fc host
params - based on the values learned during the ioc getattr request.
- Change needed to support BSG commands even on bfa init failure.
- Model description fixes for Brocade adapters.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Enhancements to FCPIM module.
- Introduced IO tag management to allocate/release IOs to FCPIM module
from a free IOtag pool.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Introduce FC credit recovery.
- Added module parameter to enable/disable credit recovery.
Bug Fixes:
- Removed check for ignoring plogi from initiator in switched fabric mode.
- The ABTS for PLOGI is going out few millisecs earlier due to FW
timer calibration (around 300 miilisecs earlier). So there is a
window if an accept comes during this time HBA would have initiated
an ABORT.
- Added 1 to FC_ELS_TOV for compensating for FW timer.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support for 16Gbps.
- Added logic to flush pending mailbox command queue when IOC is disabled.
- Fix to Halt the flash controller during fw initialization - since
when asic blck is programmed flash controller's continuous access
blocks f/w access to flash.
- Added new asic based card types and modified IOC get card model routine.
- Added PLL init fix to do LPU reset every time we do a memory
initialization, since not doing so will cause LPU to be
uninitialized during driver load.
- Added fix to Halt flash controller before PLL initialization.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Introduced IOC poll mechanism which replaces current interrupt
based FW READY method.
- The timer based poll routine in IOC will query the ioc_fwstate
register to see if there is a state change in FW, and sends the READY event.
- Bug fixes in the new asic PLL initialization.
- Added logic to handle CPE/RME queue interrupts before iocfc config done.
1. Use the queue_process flag to see if iocfc configuration is done
in INTX mode.
2. Split the MSIX handler installation in two - one for IOC intr
handler and the other for cpe/rme queue handler - and delay
assigning queue handlers until iocfc config is done in MSIX mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to FCS lport, vport state machines to support vport
enable / disable operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support for Brocade-1860 Fabric Adapter.
- Made changes to support single firmware image per asic type.
- Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with
only minimal defines used by host.
- Added changes to setup CPE/RME Queue register offsets based on
firmware response.
- Removed queue register offset initializations and added register offsets
to BFI config response message.
- Added Brocade-1860 asic specific interrupt status definitions and
mailbox interfaces.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Introduced a generic event notification callback function that
receives IOC_ENABLED, IOC_DISABLED, IOC_FAILED events and notifies the
modules registered for these events.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Avoid the use of hardware defined structure bfi_sge_s for DMA
requests in host.
- Defined a generic address len pair to represent a DMA memory chunk
(bfi_alen_s).
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Root cause: When kernel crashes, bfa IOC state machine and FW doesn't get
a notification and hence are not cleanly shutdown. So registers holding
driver/IOC state information are not reset back to valid disabled/parking
values. This causes subsequent driver initialization to hang during kdump
kernel boot.
Fix description: during the initialization of first PCI function, reset
corresponding register when unclean shutown is detect by reading chip
registers. This will make sure that ioc/fw gets clean re-initialization.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Move the initialization of debugfs before bfa init, to enable us to
collect driver/firmware traces if init fails. Also add a printk to
display message on bfa_init failure.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch includes fixes for two issues releated to firmware download
implementation: 1) Merged memory leak fix provided by Jesper Juhl
<jj@chaosbits.net>. Basically we need to call release_firmware() after
request_firmware(). 2) fixed issues with the firmware download interface
as pointed out by Rolf Eike Beer <eike@sf-mail.de> in linux-scsi. Rearranged
the code and fixed related function protypes.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes unused functions, data strucutres, and definitions. It
also includes misc comment and formatting cleanups.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes some inactive functions and macros.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Fix iotag handling:
1) Update and check io tag for retry case.
2) Clearing upper 3 bits in io tag when an IO completes.
The 3 upper bits in io tags are used for counting FCP exchange retry.
Un-cleared bits will cause firmware to access invalid memory when the
same io tag is used for an IO to a target that doesn't support FCP
exchange retry.
3) Only check the effective bits when validating an iotag.
Other minor fixes:
1) Added trace to get FC header type with assert of unhandled packet received.
Ignore the type FC_TYPE_FC_FSS (FC_XS).
2) Fixed the adapter info display check - to check for fcmode flag even.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Direct attach is not working due to the check of PID in fcxp_send request.
- Added logic to set the lps->lp_pid with the PID assigned for n2n mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Made IOC auto_recovery synchronized and not timer based.
- Only one PCI function will attempt to recover and reinitialize
the ASIC on a failure, after all the active PCI fns
acknowledge the IOC failure.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the bfa driver is loaded a flogi is sent without the knowledge of
trunking configuration. This normal flogi causes the switch ports
which had trunking enabled to go to persistent offline. Solution is
to store the port configuration (which has trunking info) in the flash
for persistency. The firmware will read this configuration when the
very first fcport enable is received.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Move fw trace save logic to bfa_ioc_sm_fail_entry(),
so that fw trace is saved irrespective of the cause of the failure.
- Make bfa_ioc_sm_fail() a failure parking state.
- Rename bfa_ioc_sm_initfail() to a more appropriate bfa_ioc_sm_fail_retry()
as it is no longer a parking state.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove OS wrapper functions/macros, and as a result remove bfa_os_inc.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove SCSI IO callbacks, and as a result remove bfa_cb_ioim.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modified scatter gather processing to use the kernel provided
scsi_for_each_sg() macro.
1) Instead of allocating and setting up sgpg in bfa_ioim_sge_setup(),
we only do allocation. As a result, we remove
bfa_ioim_sgpg_setup() and rename bfa_ioim_sge_setup() to
bfa_ioim_sgpg_alloc().
2) bfa_ioim_send_ioreq() call scsi_for_each_sg() to handle both inline
and sgpg setup.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cleaned up one line functions.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
First round of fix for the endianess check warnings from make C=2 CF="-D__CHECK_ENDIAN__".
Signed-off-by: Maggie <xmzhang@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Rename log_level to bfa_log_level to make the global variable more bfa
specific and avoid clashes with other drivers which was causing a
build failure.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch addresses the comments from Randy Dunlap (Randy.Dunlap@oracle.com)
regarding comment blocks that begining with "/**". bfa driver comments
currently do not follow kernel-doc convention, we hence replace all
/** with /* and **/ with */.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch addresses the comments from Randy Dunlap (Randy.Dunlap@oracle.com)
regarding comment blocks that begining with "/**". bfa driver comments
currently do not follow kernel-doc convention, we hence replace all
/** with /* and **/ with */.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix compile warning for frame size over 1024 in gcc 4.4.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch replaces register access functions and macros with the the ones
provided by linux.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes os wrapper and unused functions.
bfa_os_assign(), bfa_os_memset(), bfa_os_memcpy(), bfa_os_udelay()
bfa_os_vsprintf(), bfa_os_snprintf(), and bfa_os_get_clock() are replaced with
direct assignment or native linux functions. Some unused functions related to VF
(Vitual fabric) are also removed.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We have flattened the BFA hierarchy and also reduced the number of
source and header files we used to have earlier.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'params' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (22 commits)
param: don't deref arg in __same_type() checks
param: update drivers/acpi/debug.c to new scheme
param: use module_param in drivers/message/fusion/mptbase.c
ide: use module_param_named rather than module_param_call
param: update drivers/char/ipmi/ipmi_watchdog.c to new scheme
param: lock if_sdio's lbs_helper_name and lbs_fw_name against sysfs changes.
param: lock myri10ge_fw_name against sysfs changes.
param: simple locking for sysfs-writable charp parameters
param: remove unnecessary writable charp
param: add kerneldoc to moduleparam.h
param: locking for kernel parameters
param: make param sections const.
param: use free hook for charp (fix leak of charp parameters)
param: add a free hook to kernel_param_ops.
param: silence .init.text references from param ops
Add param ops struct for hvc_iucv driver.
nfs: update for module_param_named API change
AppArmor: update for module_param_named API change
param: use ops in struct kernel_param, rather than get and set fns directly
param: move the EXPORT_SYMBOL to after the definitions.
...
A couple of scsi drivers define a BIT() macro, duplicating the one in
bitops.h.
Cc: Jing Huang <huangj@brocade.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It appears that the wrong fcport H2I message was tested
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jing Huang <huangj@Brocade.COM>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the writing to sysfs can free the old one, we need to block that
when we access the charp variables.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Jing Huang <huangj@brocade.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
- Add debugfs support to obtain firmware trace, driver trace
and read/write to registers.
- debugfs hierarchy:
/sys/kernel/debug/bfa/host#
where the host number corresponds to the one under /sys/class/scsi_host/host#
- Following are the new debugfs entries added:
drvtrc: collect current driver trace
fwtrc: collect current firmware trace.
fwsave: collect last saved fw trace as a result of firmware crash.
regwr: write one word to chip register
regrd: read one or more words from chip register.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes 3 bugs in vport create/delete.
1) Replace scsi_add_host() with scsi_add_host_with_dma()
2) Fix rmmod hang when there are vports configured. This is due to a race
condition between the workqueue destroy in pci remove context and the vport
delete works being handled. The fix is to use a counter to track the
vport delete work, so that workqueue destroy will not be called until all
configured vports are deleted from workqueue.
3) Fix rmmmod crash when there are PBC vport configured. PBC is not allowed
to be deleted dynamically. However, if someone try to delete it, it leaves the
vport is wrong state. The fix is to restore the vport back to original state
when the attempt to delete pbc vport delete is failed.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes the issue of passing wrong argument to callback function.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds ioc state checking while enabling a port.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update bfa driver API and data structure to support BOFM (IBM BladeCenter
Open Fabric Manager).
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
While processing the ioim in callback functions, the ioim is still in io_q.
During this time, if the itnim goes offline, the ioim is requeued from
itnim->io_q into itnim->delay_comp_q although the request is already completed.
This results in requeing the ioim into the callback queue if the ioim is not
freed by the time the ioim is requeued. This results in double completion of
the ioim. To fix this, whenever a response is received from firmware for an
ioim, deque it from io_q and enque to fcpim->comp_q. This will eliminate any
possibility of itnim picking any ioim for which the response is already
received.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the FCoE Linkup event is sent to the host, the link_state
(struct bfa_pport_link_s) structure is copied to the RME buf to be sent to
the host. But the size of this structure(164 bytes) is larger than the
reserved RME buffer size(128 byes). The following changes reduce the size
of the structure to be less than RME buffer size(128 bytes):
- Remove the trunk and loop info from link_state structure, because both trunk
and loop are not supported.
- Combine qos_vc_attr and fcf into an union.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add new bfa functionality to support dynamic queue selection (IO redirection).
IO redirection can only be enabled when QoS is disabled.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
BFA UF module did not hold lock when seding uf post buffer message to firmware
causing CPE-Q corruption. Fix is to check present of FCS and if FCS present
hold lock while posting UF buffers.
Handle PRLO with sending acc to it and relogin with rport. Discard fcxp
before any state change.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Clear PSS memory reset that is set as part of power-on-reset (pci reset).
Complete PMM memory reset before BISTR start. Clear EDRAM BISTR start bit
after fixed delay. BISTR DONE bit status is not getting set. Use a fixed
1ms delay for BISTR now. Expose PMM IT memory definitions to host.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update related data structures to support firmeare configuration.
Add AEN events related to firmware configuation.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add PBC port disable handling in BFA and return the appropriate status from
BFA APIs. In bfa_fcs_lport.c, handle OFFLINE event to avoid BFA_ASSERT.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add a max retry limit for PRLI retries. Max retry limit (5) is same as used
in rport PLOGI. Once the retries are exhausted, invoke rport offline so that
existing logic of rport re-discovery can kick-in. Also fixed a bug in rport.c
where one less retry was happening.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When a rport goes offline, its speed setting was not reset. Subsequently, if
the rport was not deleted due to it coming back online within rport del
timeout, previously discovered speed would continue to show up. The fix is to
reset the speed when processing rport offline transition.
In rport attributes, rport's with unknown speed were indicated as TRL
enforced. The right thing do to would be to use TRL default speed to
determine if TRL is enforced, when TRL is enabled.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Do not update the coalesce flag of the intr_attr struct in driver config area
on config response. This is to prevent the coalesce flag being reported as on
after an ioc disable/enable even if it was set to off before disable.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use standards defined 2 * RA_TOV as a timeout for ELS Request retries.
And standards defined 3 * RA_TOV as a timeout for FC-CT Request retries.
Also, added a check to send RPSC2 to a Brocade Fabric only.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Added time stamp for fcport stats reset
- Added new fileds to the statistics data structures.
- Typo removal and minor cleanup.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes the APIs to obtain ioc attributes
- fix API to obtain wwpn, wwnn, and mac.
- add API to get mfg wwpn, wwnn, and mac.
- fix API to obtain wwn of boot target.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Vport state machine does not cleanup associated lport in some states: while
waiting for fdisc response or fdisc failure state. The fixe is to cleanup lport
on vport delete in all states. In fdisc state, discard fdisc response and
delete lport and wait for lport deletecompletion. in error state, delete lport
and wait for delete completion.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch enables creating PBC vport.
During fcs init, fcs will read PBC vport using bfa iocfc API and invoke fcb
callback to add the pbc vport entries into a list. The pbc vport list will be
traversed in the subsequent pci probe process and vport will be created using
fc transport provided vport create function.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The patch includes the driver side changes to enable basic PBC (PreBoot
Configuration) feature.
- Data structure changes and new definitions for PBC.
- APIs to access PBC info.
- Remove unused code.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch enables support of new mezzanine cards for HP and IBM blade server.
- Add new pciids for HP and IBM mezzanine card.
- Add a new firmware image for HP mezzanine card, which is running in
FC only mode. Rename firmware image to reflect the difference. Change the
firmware download code accordingly for the above changes.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The port data structure related to fc_host statistics collection is
not initialized. This causes system crash when reading the fc_host
statistics. The fix is to initialize port structure during driver
attach.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
[SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
[SCSI] aacraid: prohibit access to array container space
[SCSI] aacraid: add support for handling ATA pass-through commands.
[SCSI] aacraid: expose physical devices for models with newer firmware
[SCSI] aacraid: respond automatically to volumes added by config tool
[SCSI] fcoe: fix fcoe module ref counting
[SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
[SCSI] libfcoe: Fix incorrect MAC address clearing
[SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
[SCSI] libfc: Move the port_id into lport
[SCSI] fcoe: move link speed checking into its own routine
[SCSI] libfc: Remove extra pointer check
[SCSI] libfc: Remove unused fc_get_host_port_type
[SCSI] fcoe: fixes wrong error exit in fcoe_create
[SCSI] libfc: set seq_id for incoming sequence
[SCSI] qla2xxx: Updates to ISP82xx support.
[SCSI] qla2xxx: Optionally disable target reset.
[SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
[SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
[SCSI] qla2xxx: T10 DIF support added.
...
Fix the compilation warning in powerpc. The same change also fixes endian
issue we found in powerpc test. This patch has been tested in x86 and
powerpc platform. it is created using scsi-misc-2.6.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
sg address in IO request is not set up correctly for big endian platform.
add new macros to properly swap the address.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
idr is a global resource, protect it with global bfad_mutex.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use pci_iomap() and pci_iounmap() to simplify the code. Remove uncessary #ifdef
check for ia64 (it was added as a workaound for some RHEL 5.x release which
doesn't export iounmap function)
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently the driver doesn't take into consideraion of possible sg chaining
when it walks through the sg list. This is fixed by using the sg_next()
which automatically handles the chaining case. Obosolete code is removed
as a result of this change.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use duplicate fc transport template for physical and vitual port. Add
vport create/delete/disalbe functions in the transport template of physical
port. Changes to make the vport create/delete function to work under this
framework.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The variable bfa_itnim is initialized twice to the same (side effect-free)
expression. Drop one initialization.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@forall@
idexpression *x;
identifier f!=ERR_PTR;
@@
x = f(...)
... when != x
(
x = f(...,<+...x...+>,...)
|
* x = f(...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Jing Huang <huangj@brocade.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Upgrade the upstream driver from 2.0.0.0 to 2.1.2.1.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When IO is completed with underrun and with good SCSI status, check if
the transferred bytes against scsi_cmnd->underflow, which is set to
minimum number of bytes that must be transferred for this command, if
is less than required minimum, complete the IO with DID_ERROR.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
MS module did not invoke fdmi offline in all cases,
call fdmi offline when ms module receives a port offline,
so that fdmi offline is from one place in the ms module.
Make changes to handle 10G speed in the conversion routine.
Replaced the usage of bfa_adapter_attr_s struct with specific API's.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modified the portstats get/clear logic for port physical/FCoE/QoS stats.
Added more stats to FC
Fixed some issues with FCoE stats collection.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfa_ioc_attr_s is a big structure and some times could cause
stack overflow if defined locally, so add specific APIs that
are needed to replace the use of ioc_attr local var.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Rename pport structures to fcport in BFA FCS, to resolve confusion
about the port structures in the firmware, and make sure the SG page
is setup correctly.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently BFA was not checking for IOC down condition when issuing
getstats/clearstats
Add check to see if IOC is operational, before issuing
getstats/clearstats.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use dummy interrupt handlers till chip initialization is complete.
Install real interrupt handlers after chip initialization.
Also removed msix installation code in bfa_iocfc_init().
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixed the issue of not acknowledging the command queue
full-to-non-full interrupt. Implemented separate acknowledging
functions for different ASIC and interrupt mode.
Fixed the case of missing CPE interrupt by always processing the
pending requests in the completion path.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ioc_recover failed to work in fcmode.
Fixed the code to initialize the ioc_regs.err_set during the
notify_hbfail.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace enum types with int and rearrange the fields to fix some
alignment issue.
Local var ioc_attr is causing the stack to overflow, so removed the
usage of the local ioc_attr var and now invoking an API to return the
ioc_type.
Fix some AEN issues.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Introduce a link notification state machine to handle next incoming
link events while the current event is being delivered to the driver.
When the event has been processed by the driver, the link notification
state machine will queue the next event (if there is any) to the
driver.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Made FCS authentication related changes to state machines and header
files.
Made changes in FCS state machines to handle the case when secret
string is NULL.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Changed PCI VPD to incorporate specific OEM vendors.
Added FCoE specific interrupt latency and delay params.
Added some variables needed by FIP 2.0.
Added some new logging and tracing definitions.
Added reserved members to make the structures (IOC, IOCFC) 64bit aligned.
Changed the module identifiers, as some files were moved.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Copy fpma MAC when requested by user space application. Added FPMA
mac address to the lport attributes structure.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Make sure that in direct attach mode, we do not query the name server
after a target is marked offline.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace bfa_assert() with bfa_sm_fault() to get unhandled events for
debugging.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Clear LL_HALT and PSS_ERR bit in the interrupt status register on an IOC crash.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support for faster IOC recovery after failure.
Split bfa_ioc.c into three files:
bfa_ioc.c: Common code shared between crossbow and catapult ASIC's.
bfa_ioc_cb.c: Code specific to the crossbow, reg mapping and
interrupt related routines.
bfa_ioc_ct.c: Code specific to the catapult, reg mapping and
interrupt related routines.
Fix to make sure IOC reinitialize's properly on enable request -
update the ioc_fwstate reg with BFI_IOC_FAIL on ioc disable mbox cmd
timeout.
Makefile changes to support the 2 newly added files bfa_ioc_cb.c and
bfa_ioc_ct.c.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfad.c & bfad_drv.h:
* Created a kernel thread from pci_probe that does the bfad start
operations after BFA init done on a firmware mismatch.
* The kernel thread on a fw mismatch waits for an event from IOC
call back and is woken up from bfa_cb_init() on BFA init success.
* In normal cases of no firmware mismatch this thread is terminated
in pci_probe.
bfa_fcs_lport.c, fabric.c, fcs_lport.h & vport.c:
* Split the lport init to attach time and init time code, so that
proper config attributes are set after firmware mismatch.
bfa_iocfc.c:
* Handle an IOC timer issue, where the IOC timer would expire before
the init completion and send Init fail event to the driver,
however IOC init continues and completes successfully at the later
stage. The bfa and driver were not handling this kind of deferred
init completion.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Brocade CNA currently supports only 190 vports (instead of 191),
since there are only 192 unicast cam entries reserved for FCoE.
Brocade CNA has a total of 256 unicast cam entries (192 FCoE + 64 LL)
192 cam entries = 1 burned in mac + 1 baseport FPMA mac + 190 vport
FPMA macs.
Made changes to the code to support only 190 vports.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Split bfa_fcs_init() into bfa_fcs_attach() and bfa_fcs_init().
Removed empty function definitions in FCS modules
Modified driver to call bfa_fcs_attach() and bfa_fcs_init() as needed.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added a FCS function to be called during driver init, to set the FDMI
Driver parameter.
fdmi.c: Created a disabled state when fdmi is disabled.
bfad.c:
* Added fdmi_enable driver parameter.
* Added support to call bfa_fcs_set_fdmi_param() to initialize fcs
fdmi setting.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfa_intr.c: Enable new halt interrupt in BFA.
bfi_ctreg.h: Expose new halt interrupt bit definition to host.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfa_ioc.c:
- Enable IOC auto-recovery by default.
- When CNA is in FC mode, return IOC type as FC (not FCoE)
bfa_iocfc.c:
- Set fcmode before pci initialization/setup.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Clear virtual links was not propagated upwards to bfa from fw.
This resulted in HBA and switch being in an inconsistent state.
So defined a new LPS event for clear virtual link on a vport,
and also now clear virtual link on a baseport, is sent as a
link down event from the fw.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added separate MSI-X module parameters to selectively
enable / disable MSI-X interrupts for both Brocade HBA and CNA's.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
"Definition" is misspelled "defintion" in several comments; this
patch fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
BFA_PORT_ROLE_FCP_IPFC is 0x04 so this always evaluates to true
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jing Huang <huangj@Brocade.COM>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Krishna Gudipati