Revert to using direct register writes to set the divisor and
line-control registers.
A recent change switched to using the init vendor command to update
these registers, something which also enabled support for CH341A
devices. It turns out that simply setting bit 7 in the divisor register
is sufficient to support CH341A and specifically prevent data from being
buffered until a full endpoint-size packet (32 bytes) has been received.
Using the init command also had the side-effect of temporarily
deasserting the DTR/RTS signals on every termios change (including
initialisation on open) something which for example could cause problems
in setups where DTR is used to trigger a reset.
Fixes: 4e46c410e0 ("USB: serial: ch341: reinitialize chip on
reconfiguration")
Signed-off-by: Johan Hovold <johan@kernel.org>
A recent change added support for modifying the default line-control
settings, but did not make sure that the modified settings were used as
part of reconfiguration after a device has been reset during resume.
This caused a port that was open before suspend to be unusable until
being closed and reopened.
Fixes: ba781bdf86 ("USB: serial: ch341: add support for parity, frame
length, stop bits")
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix reset-resume handling which failed to resubmit the read and
interrupt URBs, thereby leaving a port that was open before suspend in a
broken state until closed and reopened.
Fixes: 1ded7ea47b ("USB: ch341 serial: fix port number changed after
resume")
Fixes: 2bfd1c96a9 ("USB: serial: ch341: remove reset_resume callback")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to stop the interrupt URB before returning on errors during
open.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The modem-control signals are managed by the tty-layer during open and
should not be asserted prematurely when set_termios is called from
driver open.
Also make sure that the signals are asserted only when changing speed
from B0.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The private baud_rate variable is used to configure the port at open and
reset-resume and must never be set to (and left at) zero or reset-resume
and all further open attempts will fail.
Fixes: aa91def41a ("USB: ch341: set tty baud speed according to tty
struct")
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
DTR and RTS will be asserted by the tty-layer when the port is opened
and deasserted on close (if HUPCL is set). Make sure the initial state
is not-asserted before the port is first opened as well.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Checks on the operand to VMXON are performed after the check for
legacy mode operation and the #GP checks, according to the pseudo-code
in Intel's SDM.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
On interrupt delivery the PPR can only grow (except for auto-EOI),
so it is impossible that non-auto-EOI interrupt delivery results
in KVM_REQ_EVENT. We can therefore use __apic_update_ppr.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On PPR update, we set KVM_REQ_EVENT unconditionally anytime PPR is lowered.
But we can take into account IRR here already.
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PPR needs to be updated whenever on every IRR read because we
may have missed TPR writes that _increased_ PPR. However, these
writes need not generate KVM_REQ_EVENT, because either KVM_REQ_EVENT
has been set already in __apic_accept_irq, or we are going to
process the interrupt right away.
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since we're already in VCPU context, all we have to do here is recompute
the PPR value. That will in turn generate a KVM_REQ_EVENT if necessary.
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This statistic can be useful to estimate the cost of an IRQ injection
scenario, by comparing it with irq_injections. For example the stat
shows that sti;hlt triggers more KVM_REQ_EVENT than sti;nop.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a guest causes a NPF which requires emulation, KVM sometimes walks
the guest page tables to translate the GVA to a GPA. This is unnecessary
most of the time on AMD hardware since the hardware provides the GPA in
EXITINFO2.
The only exception cases involve string operations involving rep or
operations that use two memory locations. With rep, the GPA will only be
the value of the initial NPF and with dual memory locations we won't know
which memory address was translated into EXITINFO2.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
LAPIC after reset is in xAPIC mode, which poses a problem for hotplug of
VCPUs with high APIC ID, because reset VCPU is waiting for INIT/SIPI,
but there is no way to uniquely address it using xAPIC.
From many possible options, we chose the one that also works on real
hardware: accepting interrupts addressed to LAPIC's x2APIC ID even in
xAPIC mode.
KVM intentionally differs from real hardware, because real hardware
(Knights Landing) does just "x2apic_id & 0xff" to decide whether to
accept the interrupt in xAPIC mode and it can deliver one interrupt to
more than one physical destination, e.g. 0x123 to 0x123 and 0x23.
Fixes: 682f732ecf ("KVM: x86: bump MAX_VCPUS to 288")
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Slow path tried to prevent IPIs from x2APIC VCPUs from being delivered
to xAPIC VCPUs and vice-versa. Make slow path behave like fast path,
which never distinguished that.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There were three calls sites:
- recalculate_apic_map and kvm_apic_match_physical_addr, where it would
only complicate implementation of x2APIC hotplug;
- in apic_debug, where it was still somewhat preserved, but keeping the
old function just for apic_debug was not worth it
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Interrupt to self can be sent without knowing the APIC ID.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a brief description of the lockless access tracking mechanism
to the documentation of fast page faults in locking.txt.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change implements lockless access tracking for Intel CPUs without EPT
A bits. This is achieved by marking the PTEs as not-present (but not
completely clearing them) when clear_flush_young() is called after marking
the pages as accessed. When an EPT Violation is generated as a result of
the VM accessing those pages, the PTEs are restored to their original values.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MMIO SPTEs currently set both bits 62 and 63 to distinguish them as special
PTEs. However, bit 63 is used as the SVE bit in Intel EPT PTEs. The SVE bit
is ignored for misconfigured PTEs but not necessarily for not-Present PTEs.
Since MMIO SPTEs use an EPT misconfiguration, so using bit 63 for them is
acceptable. However, the upcoming fast access tracking feature adds another
type of special tracking PTE, which uses not-Present PTEs and hence should
not set bit 63.
In order to use common bits to distinguish both type of special PTEs, we
now use only bit 62 as the special bit.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
mmu_spte_update() tracks changes in the accessed/dirty state of
the SPTE being updated and calls kvm_set_pfn_accessed/dirty
appropriately. However, in some cases (e.g. when aging the SPTE),
this shouldn't be done. mmu_spte_update_no_track() is introduced
for use in such cases.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This simplifies mmu_spte_update() a little bit.
The checks for clearing of accessed and dirty bits are refactored into
separate functions, which are used inside both mmu_spte_update() and
mmu_spte_clear_track_bits(), as well as kvm_test_age_rmapp(). The new
helper functions handle both the case when A/D bits are supported in
hardware and the case when they are not.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change adds retries into the Fast Page Fault path. Without the
retries, the code still works, but if a retry does end up being needed,
then it will result in a second page fault for the same memory access,
which will cause much more overhead compared to just retrying within the
original fault.
This would be especially useful with the upcoming fast access tracking
change, as that would make it more likely for retries to be needed
(e.g. due to read and write faults happening on different CPUs at
the same time).
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change renames spte_is_locklessly_modifiable() to
spte_can_locklessly_be_made_writable() to distinguish it from other
forms of lockless modifications. The full set of lockless modifications
is covered by spte_has_volatile_bits().
Signed-off-by: Junaid Shahid <junaids@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change adds some symbolic constants for VM Exit Qualifications
related to EPT Violations and updates handle_ept_violation() to use
these constants instead of hard-coded numbers.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When using two-dimensional paging, the mmu_page_hash (which provides
lookups for existing kvm_mmu_page structs), becomes imbalanced; with
too many collisions in buckets 0 and 512. This has been seen to cause
mmu_lock to be held for multiple milliseconds in kvm_mmu_get_page on
VMs with a large amount of RAM mapped with 4K pages.
The current hash function uses the lower 10 bits of gfn to index into
mmu_page_hash. When doing shadow paging, gfn is the address of the
guest page table being shadow. These tables are 4K-aligned, which
makes the low bits of gfn a good hash. However, with two-dimensional
paging, no guest page tables are being shadowed, so gfn is the base
address that is mapped by the table. Thus page tables (level=1) have
a 2MB aligned gfn, page directories (level=2) have a 1GB aligned gfn,
etc. This means hashes will only differ in their 10th bit.
hash_64() provides a better hash. For example, on a VM with ~200G
(99458 direct=1 kvm_mmu_page structs):
hash max_mmu_page_hash_collisions
--------------------------------------------
low 10 bits 49847
hash_64 105
perfect 97
While we're changing the hash, increase the table size by 4x to better
support large VMs (further reduces number of collisions in 200G VM to
29).
Note that hash_64() does not provide a good distribution prior to commit
ef703f49a6 ("Eliminate bad hash multipliers from hash_32() and
hash_64()").
Signed-off-by: David Matlack <dmatlack@google.com>
Change-Id: I5aa6b13c834722813c6cca46b8b1ed6f53368ade
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Report the maximum number of mmu_page_hash collisions as a per-VM stat.
This will make it easy to identify problems with the mmu_page_hash in
the future.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The check in kvm_set_pic_irq() and kvm_set_ioapic_irq() was just a
temporary measure until the code improved enough for us to do this.
This changes APIC in a case when KVM_SET_GSI_ROUTING is called to set up pic
and ioapic routes before KVM_CREATE_IRQCHIP. Those rules would get overwritten
by KVM_CREATE_IRQCHIP at best, so it is pointless to allow it. Userspaces
hopefully noticed that things don't work if they do that and don't do that.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We don't treat kvm->arch.vpic specially anymore, so the setup can look
like ioapic. This gets a bit more information out of return values.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
irqchip_in_kernel() tried to save a bit by reusing pic_irqchip(), but it
just complicated the code.
Add a separate state for the irqchip mode.
Reviewed-by: David Hildenbrand <david@redhat.com>
[Used Paolo's version of condition in irqchip_in_kernel().]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Split irqchip cannot be created after creating the kernel irqchip, but
we forgot to restrict the other way. This is an API change.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The i2s clock pre-divider 1 is used for both i2s1 and sysclk.
The i2s1 is usually used for the main i2s and the pre-divider
will be set in hw_params function.
However, if i2s2 is used, the pre-divider is not set in the hw_params
function and the default value of i2s clock pre-divider 1 is too high
for sysclk and DMIC usage. Fix by overriding default divider value to 2.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=95681
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing declarations of basic string functions to string.h to allow
a clean build.
Fixes: 5be8656615 ("String-handling functions for the new x86 setup code.")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Link: http://lkml.kernel.org/r/1483781911-21399-1-git-send-email-hofrat@osadl.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We've recently added the fsid to trace events, this makes the line quite
long. To reduce the it again, remove extra spaces around = and remove
",".
Signed-off-by: David Sterba <dsterba@suse.com>
This can help us monitor truncated ordered extents.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
'inode' is an important field for btrfs_get_extent, lets trace it.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Enabling btrfs tracepoints leads to instant crash, as reported. The wq
callbacks could free the memory and the tracepoints started to
dereference the members to get to fs_info.
The proposed fix https://marc.info/?l=linux-btrfs&m=148172436722606&w=2
removed the tracepoints but we could preserve them by passing only the
required data in a safe way.
Fixes: bc074524e1 ("btrfs: prefix fsid to all trace events")
CC: stable@vger.kernel.org # 4.8+
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Florian Fainelli says:
====================
net: dsa: bcm_sf2: Couple fixes
Here are a couple of fixes for bcm_sf2, please queue these up for -stable
as well, thank you very much!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We are implementing a MDIO bus which is behind another one, so use the
nested version of the accessors to get lockdep annotations correct.
Fixes: 461cd1b03e ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.
Fixes: f458995b9a ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes for 4.10:
- Polaris 12 support
- Add new amd-gfx mailing list to MAINTAINERS file
- UVD clockgating fix
- SI dpm fixes
* 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: drop verde dpm quirks
drm/radeon: drop verde dpm quirks
drm/radeon: update smc firmware selection for SI
drm/amdgpu: update si kicker smc firmware
drm/amd/powerplay: extend smu's response timeout time.
drm/amdgpu: remove static integer for uvd pp state
drm/amd/amdgpu: add Polaris12 PCI ID
drm/amdgpu/powerplay: add Polaris12 support
drm/amd/amdgpu: add Polaris12 support (v3)
MAINTAINERS: Update mailing list for radeon and amdgpu
There is no checking valid value of maxmtu when getting it from
device tree. This resolution added the checking condition to
ensure the assignment is made within a valid range.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few fixes for 4.10.. the first fixes a long-standing logic bug, that
by luck (ie. size of packets written into RB for a submit) wasn't hit
on a3xx/a4xx but was causing intermittent GPU lockups on a5xx. And a
couple other robustness issues that Jordan noticed.
* 'msm-fixes-4.10' of git://people.freedesktop.org/~robclark/linux:
drm/msm: Verify that MSM_SUBMIT_BO_FLAGS are set
drm/msm: Put back the vaddr in submit_reloc()
drm/msm: Ensure that the hardware write pointer is valid
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Yyce
-----END PGP SIGNATURE-----
Merge tag 'tilcdc-4.10-fixes' of https://github.com/jsarha/linux into drm-fixes
tilcdc fixes for v4.10.
* tag 'tilcdc-4.10-fixes' of https://github.com/jsarha/linux:
drm: tilcdc: simplify the recovery from sync lost error on rev1
single drm fix.
* tag 'drm-misc-fixes-2017-01-04' of git://anongit.freedesktop.org/git/drm-misc:
drm: Clean up planes in atomic commit helper failure path
Johan Hovold