A real phy don't transmit the transmitted frame back to the phy. This
behaviour will confuse the 6LoWPAN and the upper IPv6 neighbour
discovery cache. We need now at least two virtual phy's to creating a
virtual wpan network.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch renames fakelb_dev_priv to fakelb_phy. We don't faking
devices here, we fake wpan phys. This avoids also confusing with the
variable priv, which is used several times in this driver to represent
this structure.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Iterate and removing items from a list, we should use
list_for_each_entry_safe instead list_for_each_entry to avoid accidents
by removing.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the default virtual wpan phys of fakelb driver from
one to two. To have one virtual phy makes no sense, because it need at
least two virtual phy's to speak to each other.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for the atusb transceiver.
The current driver supports basic functionality only. Possible further
tasks would be to sync functionality with the at86rf230 driver, because
the atusb use internally an at86rf231 transceiver. Some of these
features need a firmware update like AACK and ARET handling.
I did small changes to this driver to work with xmit_async callback and
setting of a random extended perm address.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Werner Almesberger <werner@almesberger.net>
Cc: Stefan Schmidt <s.schmidt@samsung.com>
Cc: Richard Sharpe <realrichardsharpe@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix the complete callback for going into aret on. Currently
we starting after a state change into aret on again a state change into
aret on which is not necessary.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
fakelb_hw_deliver creates a copy of the skb's header which can
potentially return NULL so we now check for this before actually
delivering to the 802.15.4 MAC layer.
Signed-off-by: Martin Townsend <martin.townsend@xsilon.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the reset states for tx power levels after running reset
procedure.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds reset values for cca ed level values after running reset
procedure.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch reworks the cca energy detection level handling. This
contains a calculation which works on all transceiver types and
add support for dump cca energy detection levels.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for get transmit power levels and reworks the
set of transmit power levels which was broken before.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch sets the at86rf230 supported cca modes. In case of at86rf212
it also can support listen before transmit.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce a flag property for the wpan phy structure.
The current flag settings in ieee802154_hw are accessable in mac802154
layer only which is okay for flags which indicates MAC handling which
are done by phy. For real PHY layer settings like cca mode, transmit
power, cca energy detection level.
The difference between these flags are that the MAC handling flags are
only handled in mac802154/HardMac layer e.g. on an interface up. The phy
settings are direct netlink calls from nl802154 into the driver layer
and the nl802154 need to have a chance to check if the driver supports
this handling before sending to the next layer.
We also check now on PHY flags while dumping and setting pib attributes.
In comparing with MIB attributes the 802.15.4 gives us an default value
which we assume when a transceiver implement less functionality. In case
of MIB settings the nl802154 layer doesn't need to check on the
ieee802154_hw flags then.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce the wpan_phy_supported struct for wpan_phy. There
is currently no way to check if a transceiver can handle IEEE 802.15.4
complaint values. With this struct we can check before if the
transceiver supports these values before sending to driver layer.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Suggested-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the handling of cca energy detection level from dbm to
mbm. This prepares to handle floating point cca energy detection levels
values. The old netlink 802.15.4 will convert the dbm value to mbm for
handling backward compatibility.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the handling of transmit power level from dbm to mbm.
This prepares to handle floating point transmit power levels values. The
old netlink 802.15.4 will convert the dbm value to mbm for handling
backward compatibility.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the transmit power from s8 to s32. This prepares to store a
mbm value instead dbm inside the transmit power variable. The old
interface keep the a s8 dbm value, which should be backward compatibility
when assign s8 to s32.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for one of the slp_tr gpio use cases which
indicates the TX_START command without doing some spi bus traffic.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a transmit ends in a calibration which means the transceiver do a
TRX_OFF state change, we can directly change into TX_ARET state instead
doing a TX_ON to TX_ARET statechange.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All supported transceivers can do a valid state change from TRX_OFF to
AACK_ON. This patch removes the state change chain from TRX_OFF ->
TX_ON -> AACK_ON instead we doing a directly state change from TRX_OFF
to AACK_ON.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a calibration timeout reset when change from TRX_OFF to
TX_ARET_ON which also occurs a calibration.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the calculation timeout of TRX_OFF to RX_AACK_ON
handling to the async state change functionality. With this patch we can
do a reset of calculation timeout when others TRX_OFF to RX_AACK_ON
happens instead of doing this on interface up only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups the at86rf230 driver to use a space instead a tab
after define.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of using the 'magic' number of 0x1f the TRX_STATE_MASK macro is
introduced.
Signed-off-by: Christoffer Holmstedt <christoffer.holmstedt@gmail.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Netlink attribute for the power is s8. But for the driver level
operations we are collection power level value into integer.
It has to be change to s8 from int.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix the error handling when is_tx is true. The error handling
tries to get the transceiver into RX_AACK_ON mode then we need to be
sure that is_tx is false.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This spinlock isn't necessary because if we are in TX_ON/TX_ARET_ON
state the transceiver can't be interrupted e.g. by receiving a frame
when a SHR was detected. In this time the transceiver doesn't leave
the TX_ON/TX_ARET_ON state until the tx complete irq change the state
into RX_AACK_ON again. This means a receiving interrupt in state
TX_ON/TX_ARET_ON can't happen and is_tx is protected by transceiver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The TI CC2521 is an RF power amplifier that is designed to interface
with the CC2520. Conveniently, it directly interfaces with the CC2520
and does not require any pins to be connected to a
microcontroller/processor. Adding a CC2591 increases the CC2520's range,
which is useful for border router and other wall-powered applications.
Using the CC2591 with the CC2520 requires configuring the CC2520 GPIOs
that are connected to the CC2591 to correctly set the CC2591 into TX and
RX modes. Further, TI recommends that the CC2520_TXPOWER and
CC2520_AGCCTRL1 registers are set differently to maximize the CC2591's
performance. These settings are covered in TI Application Note AN065.
This patch adds an optional `amplified` field to the cc2520 entry in the
device tree. If present, the CC2520 will be configured to operate with a
CC2591.
The expected pin mapping is:
CC2520 GPIO0 --> CC2591 EN
CC2520 GPIO5 --> CC2591 PAEN
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Storing the `platform_data` struct inside of the SPI struct when using
the device tree allows for a later function to edit the content of that
struct. This patch refactors the `cc2520_get_platformat_data` function
to accept a pointer to a `cc2520_platform_data` struct and populates
the fields inside of it.
This change mirrors commit aaa1c4d226
("at86rf230: copy pdata to driver allocated space").
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix an issue when at86rf230_read_subreg was successful. The
function at86rf230_read_subreg will directly call regmap_read which
returns zero on successful. Nobody figured out issues yet because it was
only necessary to evaluate dvdd state while probing. This could make
trouble because the stack variable could have an random value.
The function is also used by reset the irq line before requesting irq, but
the value isn't evaluated afterwards.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These registers are also changed by transceiver and should be volatile
for right accessing via regmap debugfs.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a handling for calibration if we are 5 minutes in PLL
state. I first tried to implement the calibration functionality in
TX_ON state via register values CF_START and DCU_START, but this occurs
a one second delay at each calibration time.
An another solution to start a calibration is to switch from TRX_OFF
state into TX_ON, then a calibration is done automatically by
transceiver. This method will be used in this patch, after each transmit
of a frame we check with jiffies if the PLL is set 5 minutes without
doing a TRX_OFF->(TX_ON || RX_AACK_ON) or channel switch. The worst case
would be a transceiver in receiving mode only, but this is under normal
operation very unlikely.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Cc: Werner Almesberger <werner@almesberger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replace the state change timing relevant sleeps with
hrtimers. Currently the sleeps are done in the complete handler of
spi_async. The relation of doing the state change timing sleep with a
timer will get the sleep functionality out of spi_async complete handler
context.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch initialize xtal_trim value to zero. The xtal_trim property is
an optional device tree value. Currently if no xtal_trim property is
given the xtal_trim value can be contain random data, because it's a
stack variable. This patch init the xtal_trim value to zero which is
also the default value after reset for at86rf230 transceivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the most cases the spi messages has a length of two. Currently we
always set the the len field to two before transmit a spi message. In
cases for read out/write in the frame buffer we need another len. This
patch use trx len two as default. For the frame buffer cases we restore
the trx len to two on success and failure. This will reduce the len
setting of two when it's already two.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups the referencing for the state change context
variable. The state change context should only set once and this is by
initial a state change. This patch will use the initial state change
variable in the complete handler of the state change by using the ctx
context which should be always the same like the initial state change
context.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By holding the irq variable inside at86rf230_state_change we can squash
some multiple dereferencing for getting irq num.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch refactor the receive handling into one function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
I had this variable because I thought it would be protected by
disable/enable irq but this is not true. It's protected by stop/wake
netdev queue which is called by ieee802154_xmit_complete.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce a transmit retry handling into at86rf230 transmit
path. Current behaviour is to wait the normal receive time if we want
to go into STATE_TX_ON when the transceiver is in STATE_BUSY_RX_AACK
which indicates that a frame is currently receiving. A non force state
change will not interrupt the the receiving state.
The current behaviour is that after the normal receive time we will
start a force change into STATE_TX_ON. With this patch we do seven
retries to go into STATE_TX_ON without forcing. After we hit the
AT86RF2XX_MAX_TX_RETRIES we will start the force state change.
This is a polling like method to go into STATE_TX_ON in times of maximum
receiving time.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
While testing I experience a deadlock while using the at86rf233 on a
raspberry pi. The reason was an edge triggered gpio irq because the irq
triggered while irq was disabled. This issue doesn't happend on a level
triggered irq because the irq will hit after calling enable_irq.
This patch adds a warning that it's not recommended to use a edge-triggered
irq type. Also change the examples to high-level irqtype.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The at86rf2xx chips supports the setting of irq polarity if active low
or active high. This patch adds a handling for IRQ_ACTIVE_LOW if the
irq_type is IRQ_TYPE_LEVEL_LOW.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we support at86rf233 we need to ensure that basic operation
default values are the same. This patch always sets IRQ_MASK_MODE to 0
which is after reset 1 at the at86rf233 and 0 at the at86rf231.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes tx_timeout handling. We used it in sync xmit
handling. Since we support async xmit handling a xmit timeout handling
isn't easy to implement and should be implemented by netdev watchdog
mechanism.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for setting the xtal trim register. Some at86rf2xx
transceiver boards needs fine tuning the xtal capacitor.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch copies the platform data in driver allocated space at first.
With this change we ensure that we access the allocated platform data as
readonly space.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
return type of wait_for_completion_timeout is unsigned long not int.
As rc is used here only for wait_for_completion_timeout the type is simply
changed to unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the warnings (space before , ) shown by
checkpatch.pl
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces the shifting operations by BIT macro
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will remove the bug of havine zero perm_extended_addr address.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If allocation of memory fails instead of going to ret goto label
and returning from there, we can directly return -ENOMEM on failure.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit ab78029ecc (drivers/pinctrl: grab default handles from device
core), we can rely on device core for setting the default pins.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This version check allows the driver to only work with v=1 hardware
however there is no driver-facing difference with newer versions
(confirmed by Atmel FAEs) so this check needlessly prevents the driver
from being used with radios now in production.
Tested on AT86RF212B radio (which came up as v=3).
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver was reading the PART_NUM register for both the part number
(type of device) and the part version, the version is actually in
register 0x1D, VERSION_NUM. I believe that this was a copy-paste error.
Tested on AT86RF212B where the part is detected to be the expected part
number (0x07) and version (0x03 on mine).
Signed-off-by: Andrey Yurovsky <andrey@snupi.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The attribute extra_tx_headroom should already be zero.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the context pointer to the parameter given one inside
function at86rf230_async_state_change_start. This could occur problem if
context isn't pointed to lp->state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes the at86rf230_async_error inline. This function is
small enough to handle inline.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes an unnecessary if branch inside the tx complete
handler.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
CC: Alan Ott <alan@signal11.us>
Signed-off-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
CC: Alan Ott <alan@signal11.us>
Signed-off-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the default cca setting after device reset for at86rf230
driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current cca setting handle is a driver specific call. We need to
introduce some 802.15.4 specific layer and mapping 802.15.4 cca modes to
driver specific ones inside the 802.15.4 driver. This patch will add
such 802.15.4 layer and mapping the cca settings to driver specific ones.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This patch fix an copy&paste issue in the comment of setting symbol
duration. These comments are more correct according the at86rf212 datasheet
now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the interframe spacing time workaround from at86rf230
driver and use the mac802154 one. The interframe spacing time differs at
at86rf212 and channel setting. This patch fix this handling which is also
a new workaround and should be moved into mac802154 while channel
setting.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new interframe spacing time handling into mac802154
layer. Interframe spacing time is a time period between each transmit.
This patch adds a high resolution timer into mac802154 and starts on
xmit complete with corresponding interframe spacing expire time if
ifs_handling is true. We make it variable because it depends if
interframe spacing time is handled by transceiver or mac802154. At the
timer complete function we wake the netdev queue again. This avoids
new frame transmit in range of interframe spacing time.
For synced driver we add no handling of interframe spacing time. This
is currently a lack of support in all synced xmit drivers. I suppose
it's working because the latency of workqueue which is needed to call
spi_sync.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the invalid max frame retries check from driver
layer. This is already handled by nl802154 framework. Also the IEEE
802.15.4 standard doesn't allow a frame retries setting above 7. This
seems to be valid for the at86rf230 transceiver but the chip running out
of spec then. We only allow settings according 802.15.4 right now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the invalid check on max csma backoffs in driver
layer. This is already handled by nl802154 framework.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the invalid backoff exponent check from driver layer.
This is already handled by nl802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes validation of page and channel while setting from
driver layer. This is already handled by nl802154 and mac802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
drivers/net/ieee802154/at86rf230.c:1365:1-3: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a force setting of slotted operation bit. The atben
chips sometimes set these bit. The reason is unknown. Nevertheless we
don't support slotted operation so we set this bit now force while
probing.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for a random generated perm extended address for
the at86rf230 driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an ieee802154_vif similar like the ieee80211_vif which
holds the interface type and maybe further more attributes like the
ieee80211_vif structure.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch sets the reset state channels accoridng at86rf2xx datasheets.
We don't need to set the default page here which is zero on all chips.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit e37d2ec82a ("mac802154: ops:
declare channel and page as u8") the page parameter can't be below zero.
This patch fix a kbuild test robot warning. Furthermore this check
should be removed and handled by netlink 802.15.4 interface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch indicates that the at86rf230 driver deliver with checksum
instead drop the crc before delivering.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for promiscuous mode setting for the at86rf230
driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Overdue introduction for address filtering hardware flag. Furthermore we
will check and set address filtering on interface up. This patch
prepares that we can check if an transceiver supports address filtering
option. Currently all mainline driver supports hardware address filtering.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new IEEE802154_HW_ARET hardware flag for indicating
that the transceiver supports ARET handling. Also remove the
IEEE802154_HW_FRAME_RETRIES from IEEE802154_HW_CSMA flag. Frame retries
handling is part of ARET.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes all might_sleep calls from driver layer. This
handling is already done by mac802154 layer.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The range of channel and page fits into an unsigned byte range. This
patch changes the set_channel parameter definitions for channel and
page to u8.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ieee802154_ops structure should be never changed during runtime.
This patch declare this structure as const to avoid a runtime change.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Current behaviour it to copy the frame inclusive CRC into a skb, then
remove the CRC from the skb. This patch optimizes this by not copying
the CRC at the first place.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the ieee802154_is_valid_psdu_len function to validate
the psdu length. If the psdu length is invalid we use the maximum
payload to receive also corrupted frames in monitor mode.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the allocation of skb inside the ieee802154 driver
layer to dev_alloc_skb. This changes also the gfp mask to GFP_ATOMIC
which is needed for upcomming change that the receiving is done by a
tasklet and not a workqueue anymore.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the sync xmit handling into an async xmit handling. The
driver was already prepared for this step, all other drivers need more
work to implement a xmit_async function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch renames the existsing xmit callback to xmit_sync and
introduces an asynchronous xmit_async function. If ieee802154_ops
doesn't provide the xmit_async callback, then we have a fallback to
the xmit_sync callback.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The identical struct of the wireless stack implementation is named
ieee80211_hw. This is useful to name the variable hw instead of get
confusing with netdev dev variable.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the not functional fakehard driver. We don't support
HardMAC 802.15.4 drivers right now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the ieee802154 header into include/linux instead
include/net. Similar like wireless which have the ieee80211 header
inside of include/linux.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The wpan-phy header contains the wpan_phy struct information. Later this
header will be have similar function like cfg80211 header. The cfg80211
header contains the wiphy struct which is identically the wpan_phy
struct inside 802.15.4 subsystem.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixs a typo in address filter defines from IEEE802515 to
IEEE802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the FSF address in files which belongs to ieee802154
and mac802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The async error function will already printout the errno over dev_err.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sometimes the async state function is call in an context where the spi
irq is diabled. This patch fix the handling to enable the irq when
spi_async failed in the async state change calling chain. We do this by
a context parameter irq_enable and evaluate this parameter when
spi_async failed instead of returning spi_async errno.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the driver waits for a tx completion currently the driver direct
enables the irq. When we switching to RX_AACK_ON some steps afterwards
the driver could receive a new frame and request resources which are
already in use, for example irq state change resource.
To be sure there are no new interrupts when we switching to RX_AACK_ON,
we enable the irq when state change to RX_AACK_ON was completed.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a missing enable_irq when spi_async in isr failed.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes dereferencing irq number over spi struct. Instead we
doing it directly over isr paramater.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds lifs/sifs handling only if max_frame_retries is above
zero. The at86rf2xx datasheets says nothing about phy lifs/sifs
handling. I asked the atmel support and they said lifs/sifs is done
by phy when max_frame_retries is above zero.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an async error handling function if sync state change
runs into a timeout. The async error handling function tries to recover
the phy state machine into a valid state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The rc variable is zero if we get a timeout. Instead of pass the rc
variable to the async error handling function which try to recover the
phy, we use a static -ETIMEDOUT errno.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The MRF24J40MC module has an external amplifier which should be
enabled. The TX power has to be lowered to meet FCC regs.
Signed-off-by: Simon Vincent <simon.vincent@xsilon.com>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove the return statement in the void function.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the current synchron state change function and add a
new function for a state assert. Change the start and stop callbacks to
use this new synchron state change behaviour. It's a wrapper around the
async state change function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rework the irq_pol register setting for rising and falling
interrupt settings only. The default behaviour should be rising flag.
Also use IRQ_TYPE_* defines instead of IRQF_* defines. There is no
functionality change but irq_get_trigger_type returns IRQ_TYPE_* defines.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set this bit in start callback which could be
called more than once.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a complete reimplementation of transmit and receive
handling for the at86rf230 driver.
It solves also six bugs:
First:
The RX_SAFE_MODE is enabled and the transceiver doesn't leave the
receive state while the framebuffer isn't read by a CMD_FB command.
This is useful to read out the frame and don't get into another receive
or transmit state, otherwise the frame would be overwritten.
The current driver do twice CMD_FB calls, the first one leaves this
protection.
Second:
Sometimes the CRC calculation is correct and the length field is greater
127. The current mac802154 layer and filter of a at86rf2xx doesn't check
on this and the kernel crashes. In this case the frame is corrupted, we
send the whole receive buffer to the next layer which can be useful for
sniffing.
Thrid:
There is a undocumented race condition. When we are go into the
RX_AACK_ON state the transceiver could be changed into RX_AACK_BUSY
state. This is a normal behaviour. In this case the transceiver received
a SHR while assert wasn't finished.
Fourth:
It also handle some more "correct" state changes. In aret mode the
transceiver need to go to TX_ON before the transceiver go into
RX_AACK_ON.
Fifth:
The programming model [0] describes also a error handling in ARET mode
if the trac status is different than zero. This is patch adds support
for handling this.
Sixth:
In receive handling the transceiver should also get the trac status
according [0]. The driver could use the trac status as error statistic
handling, but the driver doesn't use this currently. There is maybe some
timing behaviour or the read of this register change some transceiver
states.
In addition the irqworker is removed. Instead we do async spi calls and
no scheduling is involved anymore. The transmit function is also
asynchron but with a wait_for_completion handling. The mac802154 layer
doesn't support asynchron transmit handling right now.
The state change behaviour is now changes, before it was:
1. assert while(!STATE_TRANSITION_IN_PROGRESS)
2. state change
3. assert while(!STATE_TRANSITION_IN_PROGRESS)
4. assert once(wanted state != current state)
Sometimes a unexcepted state change occurs when 4. assert was violated.
The new state change behaviour is:
1. assert while(!STATE_TRANSITION_IN_PROGRESS)
2. state change
3. wait state change timing according datasheet
4. assert once(wanted state != current state)
This behaviour is described in the at86rf231 software programming model [0].
The state change documentation in this programming guide should also valid for
at86rf212 and at86rf233 chips.
The transceiver don't do a FORCE_TX_ON while we want to transmit a PDU.
The new behaviour is a TX_ON and wait a receiving time (tFrame + tPAck).
If we are still in RX_AACK_BUSY then we transmit a FORCE_TX_ON as timeout
handling. The different is that FORCE_TX_ON aborts receiving and TX_ON
waits if RX_AACK_BUSY is finished. This should decrease the drop rate of
packets.
[0] http://www.atmel.com/Images/AVR2022_swpm231-2.0.zip
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To set the CCA_ED_THRES register the calculation for at86rf23x is
different than for at86rf212. This patch adds a new callback for this
calculation in chip data struct.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new at86rf2xx_chip_data structure which holds device
specific attributes. Instead of runtime decisions "if (is212())" we set
callbacks/attributes while device detection.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch drops the current lowlevel spi calls for the detect device
function instead we handle this via regmap. Also put the detection of
in a seperate function and set all device specific attributes while detection.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds regmap support for the at86rf230 driver and drop the
lowlevel spi access functions and use the regmap access functions.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new mac802154 hw flags for transmit power, csma and
listen before transmit (lbt). These flags indicates that the transceiver
supports these features. If the flags are set and the driver doesn't
implement the necessary functions, then ieee802154_register_device
returns -ENOSYS "Function not implemented".
This patch merges also all at86rf230 operations into one operations structure
and set the right hw flags for the at86rf230 transceivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver support for the cc2520 radio.
Driver support:
- Tx and Rx of IEEE-802.15.4 packets
- Energy Detection on channel
- Setting the Channel for the radio. [b/w 11 - 26 channels]
- Start and Stop the radio
- h/w address filtering
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8eba0eefae ("at86rf230: remove irq_type in
request_irq") removed the trigger configuration when requesting an irq,
and instead relied on the interrupt trigger to be properly configured
already. This does not seem to be an assumption that can be safely made,
since boards disable all interrupt triggers on boot.
On these boards, force the irq to trigger on rising edge, which is also
the default for the chip.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
separate the mrf24j40 hardware initialisation from probe()
and adds the sanity checkings.
These checkings are required if somebody hasn't a right spi configuration
the probe function should fail. So we have to return from there.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
adds the device managed APIs so that no need worry about
freeing the resources.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. An explicit linux/device.h include is added to make sure
the devm_*() routine declarations are unambiguously available.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is small enough, we don't need a extra function for this.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a unnecessary state read. The status value is never
evaluate after reading the state.
Also rename the status variable to dvdd, because this variable will be
used later.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resets the irq line before we are requesting the irq. This
avoids pending interrupts before requesting.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is already handled by the of_match_ptr macro.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a at86rf230_device_id table to offers various module
aliases.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace the gpio_request functions with devm_gpio_request_one
functions. Then we don't need to take care about freeing gpios.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace request_irq with devm_request_irq. With
devm_request_irq we don't need to care about freeing the irq.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to set these values at request_irq. The interrupt line is
already configured to same value like irq_get_trigger_type returned.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the platform data for the irq_type. We use instead
the irq_get_trigger_type function to get these flags which should
already configured by the interrupt controller.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __at86rf230_read_subreg function don't mask and shift register
contents which it should do. This patch adds the necessary masks and
shift operations in this function.
Since we have csma support this can make some trouble on state changes.
Since CSMA support turned on some bits in the TRX_STATUS register that
used to be zero, not masking broke checking of the TRX_STATUS field
after commanding a state change.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVDD regulator is only enabled when the RF section is active TX_ON
(PLL_ON) state. Since commit 7dcbd22a97
("ieee802154: ensure that first RF212 state comes from TRX_OFF").
We are in TRX_OFF state at the time at86rf230_hw_init is run.
Note that this test would only fail in case of a severe hardware
malfunction (faulty/shorted power supply, etc.) so it wasn't all that
useful in the first place.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix a copy&paste failure for setting the MAX_CSMA_RETRIES
value of the at86rf212 chip which was introduced by commit
f2fdd67c6b ("ieee802154: enable
smart transmitter features of RF212")
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netback/netback.c
A bug fix overlapped with changing how the netback SKB control
block is implemented.
Signed-off-by: David S. Miller <davem@davemloft.net>
While transmit over a at86rf231 device and unloading the module I got:
[ 29.643073] WARNING: CPU: 0 PID: 3 at kernel/workqueue.c:1335 __queue_work+0xb4/0x224()
[ 29.651457] Modules linked in: at86rf230(-) autofs4
[ 29.656612] CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: G W 3.14.0-rc6-01602-g902659e-dirty #294
[ 29.666490] [<c00124f0>] (unwind_backtrace) from [<c0010ad0>] (show_stack+0x10/0x14)
[ 29.674628] [<c0010ad0>] (show_stack) from [<c0032c80>] (warn_slowpath_common+0x60/0x80)
[ 29.683116] [<c0032c80>] (warn_slowpath_common) from [<c0032d30>] (warn_slowpath_null+0x18/0x20)
[ 29.692329] [<c0032d30>] (warn_slowpath_null) from [<c0045b08>] (__queue_work+0xb4/0x224)
[ 29.700906] [<c0045b08>] (__queue_work) from [<c0045cc8>] (queue_work_on+0x50/0x78)
[ 29.708944] [<c0045cc8>] (queue_work_on) from [<c05669cc>] (mac802154_tx+0x1e4/0x240)
[ 29.717164] [<c05669cc>] (mac802154_tx) from [<c0471814>] (dev_hard_start_xmit+0x2f0/0x43c)
[ 29.725926] [<c0471814>] (dev_hard_start_xmit) from [<c04878d0>] (sch_direct_xmit+0x64/0x2a0)
[ 29.734867] [<c04878d0>] (sch_direct_xmit) from [<c0487c38>] (__qdisc_run+0x12c/0x18c)
[ 29.743169] [<c0487c38>] (__qdisc_run) from [<c046e1b0>] (net_tx_action+0xe0/0x178)
[ 29.751205] [<c046e1b0>] (net_tx_action) from [<c0036690>] (__do_softirq+0x100/0x264)
[ 29.759420] [<c0036690>] (__do_softirq) from [<c0036818>] (run_ksoftirqd+0x24/0x4c)
[ 29.767453] [<c0036818>] (run_ksoftirqd) from [<c005232c>] (smpboot_thread_fn+0x128/0x13c)
[ 29.776121] [<c005232c>] (smpboot_thread_fn) from [<c004c3fc>] (kthread+0xd0/0xe4)
[ 29.784061] [<c004c3fc>] (kthread) from [<c000da88>] (ret_from_fork+0x14/0x2c)
[ 29.791628] ---[ end trace 3406ff24bd973834 ]---
The problem is there are still interrupts after deregister ieee802154
device. This patch mask all interrupts in the at86rf2xx chips before
deregister the device.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds devicetree support for the at86rf230 driver.
Possible gpios to configure are "reset-gpio" and "sleep-gpio".
Also add support to configure the "irq-type" for the irq polarity
register.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch make the reset pin optionally. Some devices like the atben
from qi-hardware don't have a reset pin externally. The usually way is
to turn power off/on for the atben device to initiate a device reset.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While checkpatch another patch I got a:
"WARNING: msleep < 20ms can sleep for up to 20ms"
The datasheet of at86rf231 and at86rf212 says a minimum delay for reset
pulse width and spi access latency after reset is 625 nanoseconds.
This patch removes the 1 milliseconds sleep and replace it with a 1
microseconds udelay which should be also okay for the reset pulse width.
To change the state from RESET -> TRX_OFF the at86rf230 device needs 120
microseconds, this is a worst case of all at86rf* chips.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to lock the clearing of IRQ_TRX_END in status.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix a unexpected state change for the at86rf231 chip.
We can't change into STATE_FORCE_TX_ON while the chip is in one of
SLEEP, P_ON, RESET, TRX_OFF, and all *_NOCLK states.
In this case we are in the TRX_OFF state. See datasheet [1] page 71 for
more information.
Without this patch you will get the following message on a at86rf231 device:
[ 20.065218] unexpected state change: 8, asked for 4
[ 20.070527] ------------[ cut here ]------------
[ 20.075414] WARNING: CPU: 0 PID: 160 at net/mac802154/ieee802154_dev.c:43 mac802154_slave_open+0x70/0xb8()
[ 20.085594] Modules linked in: autofs4
[ 20.089667] CPU: 0 PID: 160 Comm: ifconfig Not tainted 3.14.0-20140108-1-00993-g905c192 #162
[ 20.098612] [<c00127b8>] (unwind_backtrace) from [<c0010b1c>] (show_stack+0x10/0x14)
[ 20.106819] [<c0010b1c>] (show_stack) from [<c0033838>] (warn_slowpath_common+0x60/0x80)
[ 20.115311] [<c0033838>] (warn_slowpath_common) from [<c00338e8>] (warn_slowpath_null+0x18/0x20)
[ 20.124590] [<c00338e8>] (warn_slowpath_null) from [<c057b7e8>] (mac802154_slave_open+0x70/0xb8)
[ 20.133880] [<c057b7e8>] (mac802154_slave_open) from [<c0488a58>] (__dev_open+0xa8/0x108)
[ 20.142553] [<c0488a58>] (__dev_open) from [<c0488cb0>] (__dev_change_flags+0x8c/0x148)
[ 20.151051] [<c0488cb0>] (__dev_change_flags) from [<c0488d84>] (dev_change_flags+0x18/0x48)
[ 20.159968] [<c0488d84>] (dev_change_flags) from [<c04e2e9c>] (devinet_ioctl+0x2b0/0x63c)
[ 20.168623] [<c04e2e9c>] (devinet_ioctl) from [<c04712e4>] (sock_ioctl+0x23c/0x29c)
[ 20.176727] [<c04712e4>] (sock_ioctl) from [<c00e3cb8>] (do_vfs_ioctl+0x4a8/0x578)
[ 20.184671] [<c00e3cb8>] (do_vfs_ioctl) from [<c00e3dd4>] (SyS_ioctl+0x4c/0x78)
[ 20.192402] [<c00e3dd4>] (SyS_ioctl) from [<c000da00>] (ret_fast_syscall+0x0/0x48)
[ 20.200392] ---[ end trace 9a34542f4ea08e47 ]---
This patch was tested on at86rf231 and at86rf212.
[1] http://www.atmel.com/images/doc8111.pdf
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all internal uses of ieee802154_addr_sa to ieee802154_addr,
except for those instances that communicate directly with userspace.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable sparse warnings about endianness, replace the remaining fields
regarding network operations without explicit endianness annotations
with such that are annotated, and propagate this through the entire
stack.
Uses of ieee802154_addr_sa are not changed yet, this patch is only
concerned with all other fields (such as address filters, operation
parameters and the likes).
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct as currently defined uses host byte order for some fields,
and most big endian/EUI display byte order for other fields. Inside the
stack, endianness should ideally match network byte order where possible
to minimize the number of byteswaps done in critical paths, but this
patch does not address this; it is only preparatory.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rf233 and rf231 are sufficiently similar that we can treat
rf233 like rf231.
rf233 is missing some features that rf231 has, but we don't currently
make use of them so there's nothing to handle differently yet.
Should we add support in the future for rf231 *_NOCLK or SLEEP states,
or PAD_IO drive strength, exceptions will need to be made for rf233.
Signed-off-by: Thomas Stilwell <stilwellt@openlabs.co>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some whitespace issues in Kconfig files of IEEE
802.15.4 subsytem.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 8fad346f36
(ieee802154: add basic support for RF212 to at86rf230 driver)
we support at86rf212 as well.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 9b2777d608 ("ieee802154: add TX power control to
wpan_phy") introduced the new function at86rf212_set_txpower() with
the questionable check of the return of __at86rf230_write() in the
exit path:
1) Both at86rf212_set_txpower() and __at86rf230_write() have the
same return type.
2) Whatever __at86rf230_write() returns becomes the return value of
at86rf212_set_txpower().
Thus, fix the exit path by getting rid of that check entirely.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 8fad346f36 ("eee802154: add basic support for RF212 to
at86rf230 driver") introduced the new function is_rf212() with some
minor issues in declaration:
1) Fix the function type by changing it to bool as the function
definition returns a boolean value. Additionally both callers of
is_rf212() are expected to return a boolean value.
2) Fix the function specifier by deleting the inline keyword as the
compiler takes care of that.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does multiple things:
* add .set_csma_params and .set_frame_retries for the RF212 radio.
This should work fine with RF230, but since I have no RF230 radios to
test with, RF230 does not implement these right now
* enable TX_ARET for frame retransmission limits greater than -1
Since RF230 has no operations to change CSMA parameters or frame retry
limits, RF230 will not be able to enter TX_ARET with this patch.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A documented erratum of the RF212 chip describes that some versions of
RF212 may not be properly reset by the standard reset procedure. The
described workaround seems to not fully work either; my RF212 chips will
not correctly receive any frames unless they are taken from RX mode to
TRX_OFF and back to RX mode, effectively forcing a up-down-up-cycle.
Going to TRX_OFF and to RX without intermediate state changes at least
once fixes this.
The same transition is allowed for RF230, so simply do it all the time.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since three of the four clear channel assesment modes make use of energy
detection, provide an API to set the energy detection threshold.
Driver support for this is available in at86rf230 for the RF212 chips.
Since for these chips the minimal energy detection threshold depends on
page and channel used, add a field to struct at86rf230_local that stores
the minimal threshold. Actual ED thresholds are configured as offsets
from this value.
For RF212, setting the ED threshold will not work before a channel/page
has been set due to the dependency of energy detection in the chip and
the actual channel/page selected.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard describes four modes of clear channel assesment: "energy
above threshold", "carrier found", and the logical and/or of these two.
Support for CCA mode setting is included in the at86rf230 driver,
predicated for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Listen-before-talk is an alternative to CSMA in uncoordinated networks
and prescribed by european regulations if one wants to have a device
with radio duty cycles above 10% (or less in some bands). Add a phy
property to enable/disable LBT in the phy, including support in the
at86rf230 driver for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard assigns channel 0 on page 2 to be 100kbps QPSK in the
868.3MHz band. Add support to the at86rf230 driver for this channel and
page, at the moment predicated only for the RF212 chip.
Per the datasheet, configurations for page 0, channels 0 to 10 and page
2, channels 0 to 10 differ only in the BPSK_QPSK bit. Support for
channels 1 to 10 is untested.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the current u8 transmit_power in wpan_phy with s8 transmit_power.
The u8 field contained the actual tx power and a tolerance field,
which no physical radio every used. Adjust sysfs entries to keep
compatibility with userspace, give tolerances of +-1dB statically there.
This patch only adds support for this in the at86rf230 driver and the
RF212 chip. Configuration calculation for RF212 is also somewhat basic,
but does the job - the RF212 datasheet gives a large table with
suggested values for combinations of TX power and page/channel, if this
does not work well, we might have to copy the whole table.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IEEE802.15.4 stack assumes that a radio will never deliver
packets with a bad CRC into the stack, as required by the standard.
at86rf230 driven radios violates this assumption because of another
incompatibility: devices are required to send ACKs if requested by a
sender, but RF2xx will only send ACKs from a special receive mode that
is currently not used by the driver.
Enable this receive mode to fix both bugs. Frames with bad CRCs will not
be received at all, and ACKs will be sent if so requested.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the AT86RF2xy chips are mostly compatible, this is only a small
change to the actual driver code. The at86rf230 driver already supports the
RF212 in most places, only three small adjustments are required:
* force the initial state after P_ON to FORCE_TRX_OFF to work around a
documented erratum
* channels_supported depends on the frequency of the transceiver, and
thus is_rf212
* do early detection of chip version select an appropriate _ops struct
based on the chip version.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mrf24j40 generates level interrupts. There are rare cases where it
appears that the interrupt line never gets de-asserted between interrupts,
causing interrupts to be lost, and causing a hung device from the driver's
perspective. Switching the driver to interpret these interrupts as
level-triggered fixes this issue.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate all the workqueue and interrupt enable/disable.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids a race condition where complete(tx_complete) could be called
before tx_complete is initialized.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented separate irq handling for edge and level type interrupt
configuration. For edge type interrupts calls to disable_irq_nosync()
and enable_irq() are removed. The at86rf230 resets the irq line only
after the irq status register is read. Disabling the irq can lock the
driver in situations where a irq is set by the radio while the driver
is still reading the frame buffer.
With irq_type configuration set to 0 the original behavior is
preserverd.
Additional the irq filter register is set to filter out all unused
interrupts and the irq status register is read in the probe
function to clear the irq line.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Conflicts:
drivers/net/ieee802154/at86rf230.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option to at86rf230 platform data to configure the type of the
interrupt used by the driver. The irq polarity of the device will
be configured accordingly.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_spi_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the MRF24J40, link-layer acknowledgment request and retry must be
turned on explicitly for each packet. Turn this on in the hardware based
on the FC_ACK_REQ bit being set in the packet.
Also, now that failure to receive an ACK will cause the hardware to report
failure of transmission, change the log level for this failure to debug
level.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
In at86rf230_probe() lp was first set to dev->priv and a few lines later
dev->priv was set to lp again, without changing lp in between. The call
to ieee802154_unregister_device() before err_irq: was unreachable.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It served no purpose: we never call it from anywhere in the stack
and the only driver that did implement it (fakehard) merely provided
a dummy value.
There is also considerable doubt whether it would make sense to
even attempt beacon processing at this level in the Linux kernel.
Signed-off-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register names have been wrong since the beginning but it only showed up now
as they are actualy used for the upcoming auto ACK support.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the filter function to update short address, pan id and ieee
address on change. Allowing for hardware address filtering needed for
auto ACK.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load the 64-bit Extended (IEEE) address into the hardware in the proper
byte order.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon consulting the datasheet further, it does indicates a maximum speed
for SCK at 10MHz.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue a warning if a transmit complete interrupt doesn't happen in time.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to implement empty suspend/resume callbacks if there is nothing
to do during suspend/resume. The drivers will behave the same with no callbacks
or empty callbacks during suspend/resume.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The network merge brought in a few users of functions that got
deprecated by the workqueue cleanups: the 'system_nrt_wq' is now the
same as the regular system_wq, since all workqueues are now non-
reentrant.
Similarly, remove one use of flush_work_sync() - the regular
flush_work() has become synchronous, and the "_sync()" version is thus
deprecated as being superfluous.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver for the Microchip MRF24J40 802.15.4 WPAN module.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE 802.15.4 standard represents a networking protocol. I don't
exactly know why drivers for this protocol are stored into the root
'driver' folder, but better will be to store them with other
networking stuff. Currently there are only 3 drivers available for
IEEE 802.15.4 stack, so lets do it now with the smallest overhead.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring