This introduces two macros: RGA_COLOR_FMT_IS_YUV and RGA_COLOR_FMT_IS_RGB
which allow quick checking of the colorspace familily of a RGA color format.
These macros are then used to refactor the logic for CSC mode selection.
The two nested tests for input colorspace are simplified into a single one,
with a logical and, making the whole more readable.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
fimc_md_get_pinctrl() misses a check for pinctrl_lookup_state().
Add the missed check to fix it.
Fixes: 4163851f7b ("[media] s5p-fimc: Use pinctrl API for camera ports configuration]")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's not possible for "pcdev->mclk" to be zero because we check for
that earlier and set it to 20000000 in that situation. If it were
possible, that would be a problem because it could have lead to an Oops
in the error handling when we call v4l2_clk_unregister(pcdev->mclk_clk);
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since the driver was picked-up the starting of the PHY have changed
quiet a bit. An artifact of these changes is the now poorly named
callback confirm_start(). It used to confirm start of the PHY but now
performs post PHY start initialization, rename it to phy_post_init() to
reflect this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Several drivers implement the same enclosed_rectangle() function to
check if a rectangle is enclosed into another. Replace this with the
newly added v4l2_rect_enclosed() helper function.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds support for MEDIA_BUS_FMT_SRGGB8_1X8 format for CSI2
input.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for MEDIA_BUS_FMT_SRGGB8_1X8 format in rcar-vin by setting
format type to RAW8 in VNMC register and appropriately setting the bpp
and bytesperline to enable V4L2_PIX_FMT_SRGGB8.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Up until now the VIN was capable to convert any of its supported input mbus
formats to any of it's supported output pixel formats. With the addition of
RAW formats this is no longer true.
This patch invalidates the pipeline by adding a check if given vin input
format can be converted to supported output pixel format.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently we are considering the instances which are available
in core->inst list for load calculation in min_loaded_core()
function, but this is incorrect because by the time we call
decide_core() for second instance, the third instance not
filled yet codec_freq_data pointer.
Solve this by considering the instances whose session has started.
Cc: stable@vger.kernel.org # v5.7+
Fixes: 4ebf969375 ("media: venus: introduce core selection")
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove the confusing SoC Camera reference.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since components are registered in a list, the numeric component id that
specified a location in an array is not necessary.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The functions mtk_mdp_register/unregister_component have been created to
add / remove items from the list of components.
This will eventually enable us to specify a list of components in the
device tree instead of hardcoding them into this driver.
The list is modified by a single thread at driver probe time, and will
not be traversed by another thread until the call to pm_runtime_enable
at the end of probing.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo I Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is a cleanup to better handle errors during MDP probe.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is a cleanup to better handle errors during MDP probe.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These fields are not used and can be removed.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo I Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The mtk-mdp driver uses states to check if the formats have been set
on the capture and output when turning the streaming on, setting
controls or setting the selection rectangles.
Those states are reset when 0 buffers are requested like when checking
capabilities.
This patch removes all format checks and set one by default as queues in
V4L2 are expected to always have a format set.
https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-streamon.htmlhttps://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-g-ctrl.htmlhttps://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-g-selection.html
Signed-off-by: Francois Buergisser <fbuergisser@chromium.org>
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo I Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes coccicheck warning:
./drivers/media/platform/coda/coda-jpeg.c:331:3-31:
alloc with no test, possible model on line 354
Add NULL check after kmalloc.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently for msm_csiphy, msm_csid, and msm_ispif subdevices the media
entity function field is set to MEDIA_ENT_F_IO_V4L. This is incorrect
as MEDIA_ENT_F_IO_V4L implies V4L2 video node.
Change it to MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER as this is the best
fit from the functions defined in include/uapi/linux/media.h.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Tested-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200625130836.1916-2-joro@8bytes.org
After mm.h was removed from the asm-generic version of cacheflush.h,
s390 allyesconfig shows several warnings of the following nature:
In file included from arch/s390/include/generated/asm/cacheflush.h:1,
from drivers/media/platform/omap3isp/isp.c:42:
include/asm-generic/cacheflush.h:16:42: warning: 'struct mm_struct' declared inside parameter list will not be visible outside of this definition or declaration
As Geert and Laurent point out, this driver does not need this header in
the two files that include it. Remove it so there are no warnings.
Link: http://lkml.kernel.org/r/20200622234740.72825-2-natechancellor@gmail.com
Fixes: e0cf615d72 ("asm-generic: don't include <linux/mm.h> in cacheflush.h")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
preview_init_entities() does not call v4l2_ctrl_handler_free() when
it fails.
Add the missed function to fix it.
Fixes: de1135d44f ("[media] omap3isp: CCDC, preview engine and resizer")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mccic_register() forgets to cleanup the notifier in its error handler.
mccic_shutdown() also misses calling v4l2_async_notifier_cleanup().
Add the missed calls to fix them.
Fixes: 3eefe36cc0 ("media: marvell-ccic: use async notifier to get the sensor")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When platform_get_resource() returns an error code, a
pairing runtime PM usage counter decrement is needed
to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced. For all error
paths after pm_runtime_get_sync(), things are the same.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Xilinx MIPI CSI-2 Rx Subsystem soft IP is used to capture images
from MIPI CSI-2 camera sensors and output AXI4-Stream video data ready
for image processing. Please refer to PG232 for details.
The CSI2 Rx controller filters out all packets except for the packets
with data type fixed in hardware. RAW8 packets are always allowed to
pass through.
It is also used to setup and handle interrupts and enable the core. It
logs all the events in respective counters between streaming on and off.
The driver supports only the video format bridge enabled configuration.
Some data types like YUV 422 10bpc, RAW16, RAW20 are supported when the
CSI v2.0 feature is enabled in design. When the VCX feature is enabled,
the maximum number of virtual channels becomes 16 from 4.
Signed-off-by: Vishal Sagar <vishal.sagar@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----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=HeJz
-----END PGP SIGNATURE-----
Merge tag 'media/v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull more media updates from Mauro Carvalho Chehab:
- a set of atomisp patches. They remove several abstraction layers, and
fixes clang and gcc warnings (that were hidden via some macros that
were disabling 4 or 5 types of warnings there). There are also some
important fixes and sensor auto-detection on newer BIOSes via ACPI
_DCM tables.
- some fixes
* tag 'media/v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (95 commits)
media: rkvdec: Fix H264 scaling list order
media: v4l2-ctrls: Unset correct HEVC loop filter flag
media: videobuf2-dma-contig: fix bad kfree in vb2_dma_contig_clear_max_seg_size
media: v4l2-subdev.rst: correct information about v4l2 events
media: s5p-mfc: Properly handle dma_parms for the allocated devices
media: medium: cec: Make MEDIA_CEC_SUPPORT default to n if !MEDIA_SUPPORT
media: cedrus: Implement runtime PM
media: cedrus: Program output format during each run
media: atomisp: improve ACPI/DMI detection logs
media: Revert "media: atomisp: add Asus Transform T101HA ACPI vars"
media: Revert "media: atomisp: Add some ACPI detection info"
media: atomisp: improve sensor detection code to use _DSM table
media: atomisp: get rid of an iomem abstraction layer
media: atomisp: get rid of a string_support.h abstraction layer
media: atomisp: use strscpy() instead of less secure variants
media: atomisp: set DFS to MAX if sensor doesn't report fps
media: atomisp: use different dfs failed messages
media: atomisp: change the detection of ISP2401 at runtime
media: atomisp: use macros from intel-family.h
media: atomisp: don't set hpll_freq twice with different values
...
Commit 9495b7e92f ("driver core: platform: Initialize dma_parms for
platform devices") in v5.7-rc5 added allocation of dma_parms structure to
all platform devices. Then vb2_dma_contig_set_max_seg_size() have been
changed not to allocate dma_parms structure and rely on the one allocated
by the device core. Lets allocate the needed structure also for the
devices created for the 2 MFC device memory ports.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 9495b7e92f ("driver core: platform: Initialize dma_parms for platform devices")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Patch series "mm: consolidate definitions of page table accessors", v2.
The low level page table accessors (pXY_index(), pXY_offset()) are
duplicated across all architectures and sometimes more than once. For
instance, we have 31 definition of pgd_offset() for 25 supported
architectures.
Most of these definitions are actually identical and typically it boils
down to, e.g.
static inline unsigned long pmd_index(unsigned long address)
{
return (address >> PMD_SHIFT) & (PTRS_PER_PMD - 1);
}
static inline pmd_t *pmd_offset(pud_t *pud, unsigned long address)
{
return (pmd_t *)pud_page_vaddr(*pud) + pmd_index(address);
}
These definitions can be shared among 90% of the arches provided
XYZ_SHIFT, PTRS_PER_XYZ and xyz_page_vaddr() are defined.
For architectures that really need a custom version there is always
possibility to override the generic version with the usual ifdefs magic.
These patches introduce include/linux/pgtable.h that replaces
include/asm-generic/pgtable.h and add the definitions of the page table
accessors to the new header.
This patch (of 12):
The linux/mm.h header includes <asm/pgtable.h> to allow inlining of the
functions involving page table manipulations, e.g. pte_alloc() and
pmd_alloc(). So, there is no point to explicitly include <asm/pgtable.h>
in the files that include <linux/mm.h>.
The include statements in such cases are remove with a simple loop:
for f in $(git grep -l "include <linux/mm.h>") ; do
sed -i -e '/include <asm\/pgtable.h>/ d' $f
done
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-1-rppt@kernel.org
Link: http://lkml.kernel.org/r/20200514170327.31389-2-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This seems to lead to some crazy include loops when using
asm-generic/cacheflush.h on more architectures, so leave it to the arch
header for now.
[hch@lst.de: fix warning]
Link: http://lkml.kernel.org/r/20200520173520.GA11199@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Will Deacon <will@kernel.org>
Cc: Nick Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/20200515143646.3857579-7-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement a notifier bound op to register media links from the remote
sub-device's source pad(s) to the video-mux sink pad(s).
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use v4l2_subdev_get_fwnode_pad_1_to_1() as the get_fwnode_pad operation.
The video mux maps fwnode port numbers and pad indexes 1:1.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of using the convenience function
v4l2_async_register_fwnode_subdev(), parse the video-mux input endpoints
and set up the async sub-devices without using callbacks. The video-mux
knows which ports it must parse (the input ports) and how to handle
unconnected remotes, so it makes the code simpler to transfer control
of endpoint parsing to the driver.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since its inclusion in v3.9, no users of the SuperH VEU mem2mem video
processing driver have appeared upstream. All VEU devices in SuperH
board code still bind to the "uio_pdrv_genirq" driver instead.
The original author marked the driver orphaned in v3.15.
Remove the driver; it can always be resurrected from git history when
needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Landley <rob@landley.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Set the V4L2_CAP_IO_MC capability flag and remove the driver specific
vidioc_enum_input, vidioc_g_input and vidioc_s_input callbacks for the
media controller enabled part of the driver. Also add support mbus_code
filtering for format enumeration.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It is spurious to call 'clk_disable_unprepare()' when
'clk_prepare_enable()' has not been called yet.
Re-order the error handling path to avoid it.
Fixes: a4260ea495 ("media: sun4i: Add H3 deinterlace driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: err_exlusive_rate -> err_exclusive_rate]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
gcc warns about empty array declarations, which we get in this driver
when compile-testing without CONFIG_OF:
drivers/media/platform/ti-vpe/cal.c:2194:34: warning: array 'cal_of_match' assumed to have one element
2194 | static const struct of_device_id cal_of_match[];
Since all users of this driver do need CONFIG_OF anyway, there is no
point in making the array definition conditional to save space, so
just remove the #ifdef and move the array up a little.
Fixes: 343e89a792 ("[media] media: ti-vpe: Add CAL v4l2 camera capture driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to latest H/W manual v1.50, the description of channel
number in the VCDT/VCDT2 register is decremented by one.
Therefore, this patch fixes it about comment.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to the v4l spec s_fmt must return EBUSY while the
particular queue is streaming. Add such check in encoder and
decoder s_fmt methods.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to stateful Codec API the decoder will process all
remaining buffers from before the source change event in
dynamic-resolution-change state and mark the last buffer with
V4L2_BUF_FLAG_LAST.
In Venus case the firmware doesn't mark that last buffer and
some mechanism have to be created in v4l decoder driver.
Fortunately the firmware interface (HFI) claims that the
decoder output buffers will be returned to v4l decoder
driver before it send the insufficient event.
In order to do that we save last queued in the driver capture
buffer in the event_notify and issue flush on output firmware
buffers queue. Once the saved buffer is returned (as a result of
flush command) we mark it as LAST. For all that possible we
extend HFI flush command with one more argument and one more
flush_done HFI driver callback.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently the list initialization is done only in
dynamic-resolution-change state, which leads to list corruptions
and use-after-free. Init list_head unconditionally in
vdec_stop_capture called by vb2 stop_streaming without takeing
into account current codec state.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Once the hfi_session_flush is issued by the vdec all queued
buffers to firmware should be returned to the v4l driver. Some
of those buffers are not processed at the time of flush command,
those buffers has filled len zero (no data). Catch that in
buffer_done callback and mark not filled capture buffers with
error state so that client can discard them.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently calling venus_helper_buffers_done() will return buffers to
user for both capture and output queues in the same call. This is
wrong because both queues are really separate and calling
stop_streaming on one queue shouldn't return buffers for the other.
Solve this by add a new queue type argument and fix the clients of
the helper function.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The array is not changed in the code, so make it const.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The hfi_destroy function is called too early in remove method. It
destroys a mutex which is used later in the .remove from pmruntime.
Solve the issue by moving hfi_destroy after last usage of the mutex.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the encoder enables the rate control algorithms if the bitrate
control is non-zero. Implement the V4L2_CID_MPEG_VIDEO_FRAME_RC_ENABLE
and V4L2_CID_MPEG_VIDEO_MB_RC_ENABLE controls to allow userspace to
choose frame-level or macroblock-level rate control updates, or to
explicitly disable rate control. Both controls are initially enabled to
keep the current behavior.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enabling CONFIG_DMA_API_DEBUG=y and CONFIG_DMA_API_DEBUG_SG=y will
enable extra validation on DMA operations ensuring that the size
restraints are met.
When using the FCP in conjunction with the VSP1/DU, and display frames,
the size of the DMA operations is larger than the default maximum
segment size reported by the DMA core (64K). With the DMA debug enabled,
this produces a warning such as the following:
"DMA-API: rcar-fcp fea27000.fcp: mapping sg segment longer than device
claims to support [len=3145728] [max=65536]"
We have no specific limitation on the segment size which isn't already
handled by the VSP1/DU which actually handles the DMA allcoations and
buffer management, so define a maximum segment size of up to 4GB (a 32
bit mask).
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 7b49235e83 ("[media] v4l: Add Renesas R-Car FCP driver")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
aliases property name must include only lowercase and '-'. Fix in dts
and driver.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer 'common' is being assigned with a value that is never read,
the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As CEC support doesn't depend on MEDIA_SUPPORT, let's
place the platform drivers outside the media menu.
As a side effect, instead of depends on PCI, seco driver
can select it (and DMI).
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The stop-state timeout needs to be over 100us as per CSI spec. With the
CAL fclk of 266 MHZ on DRA76, with the current value the driver uses,
the timeout is 24us. Too small timeout will cause failure to enable the
streaming.
Also, the fclk can be different on other SoCs, as is the case with AM65x
where the fclk is 250 MHz.
This patch fixes the timeout by calculating it correctly based on the
fclk rate.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sometimes there is a timeout when waiting for the Stop-State. Testing
shows that sometimes we need to wait more than what the current code
does. It is not clear how long this wait can be, but it is based on how
quickly the sensor provides a valid clock, and how quickly CAL syncs to
it.
Change the code to make it more obvious how long we'll wait, and set a
wider range for usleep_range. Increase the timeout to 750ms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sometimes there is a timeout when waiting for the 'ComplexIO Reset
Done'. Testing shows that sometimes we need to wait more than what the
current code does. It is not clear how long this wait can be, but it is
based on how quickly the sensor provides a valid clock, and how quickly
CAL syncs to it.
Change the code to make it more obvious how long we'll wait, and set a
wider range for usleep_range. Increase the timeout to 750ms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To make csi2_wait_for_phy() more readable, move code to separate
functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: delete empty line before } ]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Set DMA max seg size correctly to get rid of warnings on 64 bit
platforms:
DMA-API: cal 6f03000.cal: mapping sg segment longer than device claims to support [len=720896] [max=65536]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL_CSI2_CTX register has LINES field, which, according to the
documentation, should be programmed to the number of lines transmitted
by the camera. If the number of lines is unknown, it can be set to 0.
The driver sets the field to 0 for some reason, even if we know the
number of lines.
This patch sets the number of lines properly, which will allow the HW to
discard extra lines (if the sensor would send such for some reason),
and, according to documentation: "This leads to regular video timings
and avoids potential artifacts".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After ComplexIO reset, a dummy read to PHY is needed as per CAL spec to
finish the reset. Currently the driver reads a ComplexIO register, not
PHY register. Fix this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the code to enable and disable ComplexIO power to its own function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Simplify the code by using reg_write_field() where trivially possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove a bunch of IRQ defines, of which only CAL_HL_IRQ_ENABLE and
CAL_HL_IRQ_CLEAR are used, and these defines only end up obfuscating
code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These macros only obfuscate the code, so drop them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of having identical code block to handle irqs for the two CAL
ports, we can have a for loop and a single code block.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver does not print any errors on ComplexIO reset timeout or when
waiting for stop-state, making it difficult to debug and notice
problems.
Add error prints for these cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL reports various errors via IRQs, which are not handled at all by the
current driver. Add code to enable and catch those IRQs and print
errors. This will make it much easier to notice and debug issues with
sensors.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix: spaces preferred around that '-']
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that cal_runtime_get and cal_runtime_put are only direct wrappers to
pm_runtime_get/put, we can drop cal_runtime_get and cal_runtime_put.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We need to do errata handling every time CAL is being enabled. The code
is currently in cal_runtime_get(), which is not the correct place for
it.
Move the code to cal_runtime_resume, which is called every time CAL is
enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
i913_errata() sets a bit to 1 in PHY_REG10, but for some reason uses
CAL_CSI2_PHY_REG0_HSCLOCKCONFIG_DISABLE for the bit value. The value of
that macro is 1, so it works, but is still wrong.
Fix this to 1.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IRQENABLE_SET registers are (usually) not meant to be read, only written
to. The current driver needlessly uses read-modify-write cycle to enable
IRQ bits.
The read-modify-write has no bad side effects here, but it's still
better to clean this up by only using write.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the CAL driver stops streaming, it will shut everything down
without waiting for the current frame to finish. This leaves the CAL DMA
in a slightly undefined state, and when CAL DMA is enabled when the
stream is started the next time, the old DMA transfer will continue.
It is not clear if the old DMA transfer continues with the exact
settings of the original transfer, or is it a mix of old and new
settings, but in any case the end result is memory corruption as the
destination memory address is no longer valid.
I could not find any way to ensure that any old DMA transfer would be
discarded, except perhaps full CAL reset. But we cannot do a full reset
when one port is getting enabled, as that would reset both ports.
This patch tries to make sure that the DMA transfer is finished properly
when the stream is being stopped. I say "tries", as, as mentioned above,
I don't see a way to force the DMA transfer to finish. I believe this
fixes the corruptions for normal cases, but if for some reason the DMA
of the final frame would stall a lot, resulting in timeout in the code
waiting for the DMA to finish, we'll again end up with unfinished DMA
transfer. However, I don't know what could cause such a timeout.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Venus driver is voting Configuration NoC during .probe but not clear
voting in .suspend. Because of this NoC is up during shutdown also. As a
consequence the whole device could leak energy while in .suspend.
So correct this by moving voting in .resume and unvoting
in .suspend
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement pmruntime autosuspend in video decoder. This will
allow to save power while the userspace is inactive for some
reasonable period of time. Here we power-off venus core clocks
and power domain and don't touch vcodec because it is under
hardware control. The later decision is made to simplify the
code and avoid a mess in the power management code.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Each jpeg can have the huffman tables optimized for its specific content
meaning that the table lenghts and values don't match the standard table
of substitutions so there's no reason to hardcode and expect the standard
lengths, otherwise we just end up rejecting optimized jpegs altogether.
Tested on CODA960.
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Similar to commit 9ee50a9489 ("media: coda: lock capture queue wakeup
against encoder stop command"), make sure that a JPEG decoder stop
command running concurrently with a decoder finish_run always either
flags the last returned buffer or wakes up the capture queue to signal
the end of stream condition afterwards.
This was not necessary for BIT processor contexts because of the need to
release the bitstream buffer with the stream end condition. In contrast,
the JPEG decoder can be finished with decoding the image between the
time the application queues the last output buffer and the time it
issues the decoder stop command.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If a JPEG decoding application queues the last capture and output
buffers, issues a decoder stop command after the decoding is already
done, and then dequeues the last capture buffer, it is not marked as
last. Detect this condition in the decoder stop command and mark the
last buffer on the capture done list.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Split marking the last metadata entry into a helper function to simplify
coda_decoder_cmd.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds JPEG decoding support for CODA960, handling the JPEG
hardware directly. A separate JPEG decoder video device is created due
to the separate hardware unit and different supported pixel formats.
While the hardware can not change subsampling on the fly, it can decode
4:2:2 subsampled JPEG images into YUV422P.
[m.felsch@pengutronix.de: fix qsequence counting by explicitly
checking for the !use_bit case]
[hverkuil-cisco@xs4all.nl: fix 'warning: missing braces around initializer']
[mchehab+huawei@kernel.org: fix 'BRACES: Unbalanced braces around else statement']
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The BIT decoders always write 16x16 macroblocks. Align stride and height to
avoid spilling luma data into the top of the chroma planes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Changing from "depends on" to "select" may cause some
side-effects. This patch is not ready to be merged yet,
as it requires some adjustments.
So, let's revert it.
This reverts commit a3b91d8bd1.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those documents don't really describe the driver API.
Instead, they contain development-specific information.
Yet, as the main index file describes the content of it as:
"how specific kernel subsystems work
from the point of view of a kernel developer"
It seems to be the better fit.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are lots of drivers that only work when the media controller
and/or the V4L2 subdev APIs are present.
Right now, someone need to first enable those APIs before
using those drivers.
Well, ideally, drivers, should, instead *optionally*
depend on it, in order for PC camera drivers to be able to use
them, but nowadays most drivers are UVC cameras, with don't
require a sensor driver.
So, be it.
Let's instead make them select the MEDIA_CONTROLLER and the
SUBDEV API, in order to make easier for people to be able
of enabling them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Most of media Kconfig/Makefile files already has SPDX,
but there are a few ones still missing. Add it to them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Right now, if one has an hybrid TV card, it has to select
both analog and digital TV support, as otherwise the needed
core support won't be selected.
Change the logic to auto-select the core support for those
drivers, as this is a way more intuitive.
It should be noticed that, as now both DVB_CORE and VIDEO_DEV
defaults depends on selecting a hybrid cards, we had to remove
the explicit dependencies there, in order to avoid circular
dependencies.
That requires some tricks:
1) the prompt should not be not visible when an hybrid card
is selected, as the user shold not change it.
2) When a media hybrid device is selected, the modular
option for DVB_CORE and VIDEO_DEV will follow the
MEDIA_SUPPORT dependency, as we can't have a core
built with "y" with a driver built as module.
Note: while here, moved two pure V4L2 PCI drivers out of the
"hybrid" part of config and consider pvrusb2 as an hybrid
device.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the first test device was added (vivi.c), there were just
one file. I was too lazy on that time to create a separate
directory just for it, so I kept it together with platform.
Now, we have vivid, vicodec, vim2m and vimc. Also, a new
virtual driver has been prepared to support DVB API.
So, it is time to solve this mess, by placing test stuff
on a separate directory.
It should be noticed that we also have some skeleton drivers
(for V4L and for DVB). For now, we'll keep them separate,
as they're not really test drivers, but instead, just
examples. The DVB frontend ones will likely be part of a new DVB
test driver. By that time, it should make sense to move them
here as well.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the platform drivers got added, they were all part of
complex camera support. This is not the case anymore, as we
now have codecs and other stuff there too.
So, fix the dependencies, in order to not require users to
manually select something that it doesn't make sense.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- Clean up and rework the PM QoS API to simplify the code and
reduce the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370
and similar platforms where the USB plug/unplug events are
handled by the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to
run on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate driver
and update its documentation (Rafael Wysocki, Alex Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file
and use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result (Leonard
Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level
PM QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences
in a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl6B/YkSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxEjIP/jXoO1pAxq7BMx7naZnZL7pzemJfAGR7
HVnRLDo0IlsSwI7Jvuy13a0eI+EcGPA6pRo5qnBM4TZCIFsHoO5Yle47ndNGsi8r
Jd3T89oT3I+fXI4KTfWO0n+K/F6mv8/CTZDz/E7Z6zirpFxyyZQxgIsAT76RcZom
xhWna9vygOlBnFsQaAeph+GzoXBWIylaMZfylUeT3v4c4DLH6FzcbnINPkgJsZCw
Ayt1bmE0L9yiqCizEto91eaDObkxTHVFGr2OVNa/Y/SVW+VUThUJrXqV28opQxPZ
h4TiQorpTX1CwMmiXZwmoeqqsiVXrm0KyhK0lwc5tZ9FnZWiW4qjJ487Eu6TjOmh
gecT+M2Yexy0BvUGN0wIdaCLtfmf2Hjxk0trxM2blAh3uoFjf3UJ9SLNkRjlu2/b
QqWmIRRPljD5fEUid5lVV4EAXuITUzWMJeia+FiAsgx1SF3pZPar80f+FGrYfaJN
wL2BTwBx1aXpPpAkEX0kM9Rkf6oJsFATR3p7DNzyZ1bMrQUxiToWRlQBID5H6G4v
/kAkSTQjNQVwkkylUzTLOlcmL56sCvc0YPdybH62OsLXs9K4gyC8v6tEdtdA5qtw
0Up9DrYbNKKv6GrSXf8eyk2Q2CEqfRXHv2ACNnkLRXZ6fWnFiTfMgNj7zqtrfna7
tJBvrV9/ACXE
=cBQd
-----END PGP SIGNATURE-----
Merge tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These clean up and rework the PM QoS API, address a suspend-to-idle
wakeup regression on some ACPI-based platforms, clean up and extend a
few cpuidle drivers, update multiple cpufreq drivers and cpufreq
documentation, and fix a number of issues in devfreq and several other
things all over.
Specifics:
- Clean up and rework the PM QoS API to simplify the code and reduce
the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370 and
similar platforms where the USB plug/unplug events are handled by
the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to run
on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate
driver and update its documentation (Rafael Wysocki, Alex
Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file and
use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result
(Leonard Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level PM
QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences in
a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies)"
* tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (78 commits)
cpufreq: intel_pstate: Simplify intel_pstate_cpu_init()
tools/power/x86/intel_pstate_tracer: fix a broken y-axis scale
ACPI: PM: s2idle: Refine active GPEs check
ACPICA: Allow acpi_any_gpe_status_set() to skip one GPE
PM: sleep: wakeup: Skip wakeup_source_sysfs_remove() if device is not there
PM / devfreq: Get rid of some doc warnings
PM / devfreq: Fix handling dev_pm_qos_remove_request result
PM / devfreq: Fix a typo in a comment
PM / devfreq: Change to DEVFREQ_GOV_UPDATE_INTERVAL event name
PM / devfreq: Remove unneeded extern keyword
PM / devfreq: Use constant name of userspace governor
ACPI: PM: s2idle: Fix comment in acpi_s2idle_prepare_late()
cpufreq: qcom: Add support for krait based socs
cpufreq: imx6q-cpufreq: Improve the logic of -EPROBE_DEFER handling
cpufreq: Use scnprintf() for avoiding potential buffer overflow
cpuidle: psci: Split psci_dt_cpu_init_idle()
PM / Domains: Allow no domain-idle-states DT property in genpd when parsing
PM / hibernate: Remove unnecessary compat ioctl overrides
PM: hibernate: fix docs for ioctls that return loff_t via pointer
Documentation: intel_pstate: update links for references
...
With the latest cleanup in qcom scm driver the secure monitor
call for setting the remote processor state returns EINVAL when
it is called for the first time and after another scm call
auth_and_reset. The error returned from scm call could be ignored
because the state transition is already done in auth_and_reset.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mt8173 VPU firmware has been moved to a sub-folder of
linux-firmware, so load vpu-fw from the new location first,
if it fails, then from the old one.
Signed-off-by: Rui Wang <gtk_ruiwang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The initial physical address was one too low for the outputs.
E.g. if 1.0.0.0 was expected, then it was set to 0.0.0.0, and
2.0.0.0 became 1.0.0.0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Johan Korsnes <johan.korsnes@gmail.com>
Fixes: 4ee895e71a ("media: vivid: reorder CEC allocation and control set-up")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch makes use of to_vpfe() to get a pointer to vpfe_device
Signed-off-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Check the return value of of_clk_get and print an error
message if not EPROBE_DEFER.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change stm32-cec driver to not print an error message when the
device probe operation is deferred.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change stm32-cec driver to defer probe when auxiliary clock
"hdmi-cec" is registered in the system not has not been probed yet.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling ccdc_data_size_max_bit() to validate data_sz in
vpfe_ccdc_validate_param(), it's treated as an enumeration ranging from
0 to 7 while essentially it's an 32 bit unsigned integer directly from
user space. This can make the return value of ccdc_data_size_max_bit()
underflow and bypass the following check.
To fix this, an additional check is added to the following if clause to
keep this enumaration variable in range. And if its value is not legal,
return -EINVAL properly.
Signed-off-by: Changming Liu <charley.ashbringer@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After the switch to use v4l2_async_notifier_add_subdev() and
v4l2_async_notifier_cleanup(), unloading the ti_cal module would cause a
kernel oops.
This was root cause to the fact that v4l2_async_notifier_cleanup() tries
to kfree the asd pointer passed into v4l2_async_notifier_add_subdev().
In our case the asd reference was from a statically allocated struct.
So in effect v4l2_async_notifier_cleanup() was trying to free a pointer
that was not kalloc.
So here we switch to using a kzalloc struct instead of a static one.
To achieve this we re-order some of the calls to prevent asd allocation
from leaking.
Fixes: d079f94c90 ("media: platform: Switch to v4l2_async_notifier_add_subdev")
Cc: stable@vger.kernel.org
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Previously, vpu->recv_buf and send_buf are forced cast from
void __iomem *tcm. vpu->recv_buf->share_buf is passed to
vpu_ipi_desc.handler(). It's not able to do unaligned access. Otherwise
kernel would crash due to unable to handle kernel paging request.
struct vpu_run {
u32 signaled;
char fw_ver[VPU_FW_VER_LEN];
unsigned int dec_capability;
unsigned int enc_capability;
wait_queue_head_t wq;
};
fw_ver starts at 4 byte boundary. If system enables
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS, strscpy() will do
read_word_at_a_time(), which tries to read 8-byte: *(unsigned long *)addr
vpu_init_ipi_handler() calls strscpy(), which would lead to crash.
vpu_init_ipi_handler() and several other handlers (eg.
vpu_dec_ipi_handler) only do read access to this data, so they can be
const, and we can use memcpy_fromio() to copy the buf to another non iomem
buffer then pass to handler.
Fixes: 85709cbf15 ("media: replace strncpy() by strscpy()")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add encoder control for enabling/disabling frame rate control via
V4L2_CID_MPEG_VIDEO_FRAME_RC_ENABLE. It is enabled by default.
Signed-off-by: Jeffrey Kardatzke <jkardatzke@google.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes the following smatch warning in the error path:
drivers/media/platform/qcom/venus/vdec.c:968 vdec_start_streaming()
warn: inconsistent returns 'mutex:&inst->lock'.
Locked on: line 952
Unlocked on: line 963
line 968
by goto mutex unlock.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the previously introduced v4l2-mem2mem core APIs to handle the drainig,
stopped and next-buf-is-last states.
With these changes, the v4l2-compliance still passes with the following
commands :
>>>><><><><><><><><><><><><><><><><>< 15.53 fps
15.53 fps
><><><><><><><><><><><><>< 13.99 fps
13.99 fps
><><><><><><><><><><><>< 13.52 fps
13.52 fps
><><><><><><><><><><><><>< 13.41 fps
13.41 fps
><><><><><><><><><><><><>< 13.21 fps
13.21 fps
><><><><><><><><><><><>< 13.09 fps
13.09 fps
><><><><><><><
STOP ENCODER
<<<
EOS EVENT
v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits
[...]
Total for vicodec device /dev/video0: 50, Succeeded: 50, Failed: 0, Warnings: 0
The full output is available at [1]
v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits
[...]
Total for vicodec device /dev/video1: 50, Succeeded: 50, Failed: 0, Warnings: 0
The full output is available at [2]
No functional changes should be noticed.
[1] https://termbin.com/25nn
[2] https://termbin.com/dza4
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Suggested-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
disable_irqs() was mistakenly disabling all interrupts when called.
This cause all port stream to stop even if only stopping one of them.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In future patch, the release of the device will move
to the release callback of v4l2_device. Therefore the
device will be released only when the last fh will be
closed. Dynamic allocation will then be needed since
when the device is unbounded and then bounded again,
it might be that the probe callback will run before
the release of the last device is finished. In that
case both operations will run on the same memory
concurrently and cause memory corruption.
This patch also removes the pdev field of
vimc_device since it is not needed anymore.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
replace 'vimc->pdev.dev' with 'vimc->mdev.dev'
in debug prints and in assignment to
vimc_ent_device.dev. This helps to unify the debug
statements. This will also eliminate the need to use
the pdev field in vimc_device in future patch.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the dma channel request error code is EPROBE_DEFER there is no need to
print error message.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Video engine in AST2600 has the exactly same register set with
AST2500 except VR084 register which provides more precise JPEG
size read back. This commit adds support for the difference and
adds 'aspeed,ast2600-video-engine' compatible OF string.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
VP9 bitstream specification indicate segment data should reset to
default when meet key frames, intra only frames or enable error
resilience mode. So memset segmentation map buffer before every
decode process is not appropriate.
Reset segment data only when needed, then start decoder hardware
Signed-off-by: Rui Wang <gtk_ruiwang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Allwinner A83T contains rotation core which can rotate and flip images.
Add a driver for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[hverkuil-cisco@xs4all.nl: MAINTAINERS paths were out of date, fix that]
[hverkuil-cisco@xs4all.nl: VFL_TYPE_GRABBER -> _VIDEO]
[hverkuil-cisco@xs4all.nl: Fix module build]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently, v4l2_pipeline_pm_use() prototype is:
int v4l2_pipeline_pm_use(struct media_entity *entity, int use)
Where the 'use' argument shall only be set to '1' for enable/power-on,
or to '0' for disable/power-off. The integer return is specified
as only meaningful when 'use' is set to '1'.
Let's enforce this semantic by splitting the function in two:
v4l2_pipeline_pm_get and v4l2_pipeline_pm_put. This is done
for several reasons.
It makes the API easier to use (or harder to misuse).
It removes the constraint on the values the 'use' argument
shall take. Also, it removes the need to constraint
the return value, by making v4l2_pipeline_pm_put void return.
And last, it's more consistent with other kernel APIs, such
as the runtime pm APIs, which makes the code more symmetric.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit ... prevented restarting CCDC through its interrupt handler when
it's about to be disabled. It missed to address the case when CCDC might
be enabled due to queueing a buffer. Do that now.
Fixes: dd12ed17ce ("omap3isp: Don't restart CCDC if we're about to stop")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In order to use dynamic video codec assignment add a new sdm845-v2
DT compatible and new venus_resource structure to cover the binding
where all pmdomains and clocks are under the venus_core control.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Handle 10bit video streams in the decoder by using dithering, i.e
the decoder output buffers will be in 8bit format.
The runtime handling is implemented by sending v4l2 event to
userspace application, then the application should stop the
streaming on capture queue and initiate format negotiation, and
start streaming again.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Co-developed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently the core (vcodec pipelines) assignment is static. Here we
introduce dynamic load balancing across the cores depending on the
current session load. The load on earch core is calculated and core
with minimum load is assigned to given instance. This will be
applicable on Venus v4 with more than one vcodec cores.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Co-developed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Redesign core (vcodec) clock control to give the venus core more
freedom to control them in order to make possible to use core
selection feature on Venus IP v4.
Move all clock and pmdomain functions in separate file and abstract
power control with common operations per Venus IP version.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those two properties are not implemented for Venus v4 (sdm845),
thus don't set them to firmware.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace explicit use of members of struct resource by %pR to print
the resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some older MSM8916 Venus firmware versions also seem to indicate
support for encoding HEVC, even though they really can't.
This will lead to errors later because hfi_session_init() fails
in this case.
HEVC is already ignored for "dec_codecs", so add the same for
"enc_codecs" to make these old firmware versions work correctly.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ignore errors returned from kthread_stop since the
vimc subdevices should still be notified that
streaming stopped so they can release the memory for
the streaming, and also kthread should be set to NULL.
kthread_stop can return -EINTR in case the thread
did not yet run. This can happen if userspace calls
streamon and streamoff right after.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's a mistakenly written self assignment in
`static int vpfe_enum_fmt_vid_cap(..)`.
Fixed it according to Prabhakar Lad's feedback.
Signed-off-by: Cengiz Can <cengiz@kernel.wtf>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver forgets to disable and unprepare clock when remove.
Add a call to clk_disable_unprepare() to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The hardware does not support capturing the field types
V4L2_FIELD_SEQ_TB and V4L2_FIELD_SEQ_BT. To capture in these formats the
driver needs to adjust the offset of the capture buffer and capture
twice to each vb2 buffer.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To support SEQ_TB/BT not all buffers given to the hardware will be
equal, the driver needs to keep track of different buffer types. Move
the tracking of buffers given to hardware into a struct so additional
tracking fields can be associated with each buffer.
[hverkuil: fix small checkpatch warning]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In case kthread_run fails, the vimc subdevices
should be notified that streaming stopped so they can
release the memory for the streaming. Also, kthread should be
set to NULL.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This exposes the white balance configuration of the ISC as v4l2 controls
into userspace.
There are 8 controls available:
4 gain controls, sliders, for each of the BAYER components: R, B, GR, GB.
These gains are multipliers for each component, in format unsigned 0:4:9
with a default value of 512 (1.0 multiplier).
4 offset controls, sliders, for each of the BAYER components: R, B, GR, GB.
These offsets are added/substracted from each component, in format signed
1:12:0 with a default value of 0 (+/- 0)
To expose this to userspace, added 8 custom controls, in an auto cluster.
To summarize the functionality:
The auto cluster switch is the auto white balance control, and it works
like this:
AWB == 1: autowhitebalance is on, the do_white_balance button is inactive,
the gains/offsets are inactive, but volatile and readable.
Thus, the results of the whitebalance algorithm are available to userspace
to read at any time.
AWB == 0: autowhitebalance is off, cluster is in manual mode, user can
configure the gain/offsets directly. More than that, if the
do_white_balance button is pressed, the driver will perform
one-time-adjustment, (preferably with color checker card) and the userspace
can read again the new values.
With this feature, the userspace can save the coefficients and reinstall
them for example after reboot or reprobing the driver.
[hverkuil: fix checkpatch warning]
[hverkuil: minor spacing adjustments in the functionality description]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the preferred form for GPL2+, and add IBM and Intel as the authors.
The driver was initially upstreamed by Eddie from IBM, and has had major
contributions from Jae at Intel.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The aspeed video IP has some differences between SoC families. Currently
the driver decides which registers to use at compile time, which means
a single kernel can not be used between platforms.
Switch to using runtime configuration of the registers that vary between
SoC families. This is in preparation for upcoming ast2600 support.
[hverkuil: replace ;; by ;]
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the recently introduced function devm_platform_ioremap_resource to
save a few lines of code. This makes the driver match common platform
device probe patterns.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The isif_config_defaults structure is only copied into another
structure, so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Paul Kocialkowski