This merges in:
x86/build, x86/microcode, x86/spinlocks, x86/memory-corruption-check,
x86/early-printk, x86/xsave, x86/quirks, x86/setup, x86/signal,
core/signal, x86/urgent, x86/xen
* 'x86-core-v2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (142 commits)
x86: make processor type select depend on CONFIG_EMBEDDED
x86: extend processor type select help text
x86, amd-iommu: propagate PCI device enabling error
warnings: fix arch/x86/kernel/io_apic_64.c
warnings: fix arch/x86/kernel/early_printk.c
x86, fpu: check __clear_user() return value
x86: memory corruption check - cleanup
x86: ioperm user_regset
xen: do not reserve 2 pages of padding between hypervisor and fixmap.
xen: use spin_lock_nest_lock when pinning a pagetable
x86: xsave: set FP, SSE bits in the xsave header in the user sigcontext
x86: xsave: fix error condition in save_i387_xstate()
x86: SB450: deprioritize DMI quirks
x86: SB450: skip IRQ0 override if it is not routed to INT2 of IOAPIC
x86: replace a magic number with a named constant in the VESA boot code
x86 setup: remove IMAGE_OFFSET
x86 setup: remove DEF_INITSEG and DEF_SETUPSEG
Revert "x86: fix ghost EDD devices in /sys again"
x86 setup: fix ghost entries under /sys/firmware/edd take 3
x86: signal: remove indent in restore_sigcontext()
...
In opposite to the P7131 Dual this early OEM card has a male
radio antenna connector and also no remote.
We currently switch the DVB-T RF feed to the radio input, like
on the P7131 with female radio connector used also for DVB-T
and should improve this.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the ALi m5602 usb bridge and is based on
the gspca framework.
It contains code for communicating with 5 different sensors:
OmniVision OV9650, Pixel Plus PO1030, Samsung S5K83A, S5K4AA and
finally Micron MT9M111.
Signed-off-by: Erik Andren <erik.andren@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
[mchehab@redhat.com: fix m5602/Makefile]
[mchehab@redhat.com: extern debug caused conflicts. Renamed to m5602_debug]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add PCI ID and device specific tables for ADS Tech Instant HDTV.
[mchehab@redhat.com: make checkpatch happy and fix merge conflicts]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sidney Matias <sidney.matias@gmail.com> for getting GPIO
values and testing on this device.
Cc: Sidney Matias <sidney.matias@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Hans Werner for finding the problem.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding support for Hauppauge's cx88 S2 based products, based on the
cx24116 DVB-S2 demodulator.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added vendor/product id for EM2820_BOARD_PROLINK_PLAYTV_USB2
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is on behalf of Stephen Backway <stev391@email.com>, and
represents two patches I received (and some subsequent whitespace
cleanup I had due to how I pulled the patches).
From the original author:
a) Add DVB support for the Leadtek Winfast PxDVR3200 H.
b) The tuner callback previously checked the command 3 times:
1) To see if it was the XC2028_RESET_CLK
2) To see if it was not the XC2028_RESET_TUNER
3) To see if it was the XC2028_RESET_TUNER
This patch removes the third check.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Stephen Backway <stev391@email.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the DViCO FusionHDTV DVB-T Dual Express card, based on
work by Chris Pascoe and Stephen Backway.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) and CDI Brasil
(www.cdibrasil.com.br/) for sponsoring this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) and CDI Brasil
(www.cdibrasil.com.br/) for sponsoring this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (43 commits)
ext4: Rename ext4dev to ext4
ext4: Avoid double dirtying of super block in ext4_put_super()
Update ext4 MAINTAINERS file
Hook ext4 to the vfs fiemap interface.
generic block based fiemap implementation
ocfs2: fiemap support
vfs: vfs-level fiemap interface
ext4: fix xattr deadlock
jbd2: Fix buffer head leak when writing the commit block
ext4: Add debugging markers that can be used by systemtap
jbd2: abort instead of waiting for nonexistent transaction
ext4: fix initialization of UNINIT bitmap blocks
ext4: Remove old legacy block allocator
ext4: Use readahead when reading an inode from the inode table
ext4: Improve the documentation for ext4's /proc tunables
ext4: Combine proc file handling into a single set of functions
ext4: move /proc setup and teardown out of mballoc.c
ext4: Don't use 'struct dentry' for internal lookups
ext4/jbd2: Avoid WARN() messages when failing to write to the superblock
ext4: use percpu data structures for lg_prealloc_list
...
* 'x86-v28-for-linus-phase4-D' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (186 commits)
x86, debug: print more information about unknown CPUs
x86 setup: handle more than 8 CPU flag words
x86: cpuid, fix typo
x86: move transmeta cap read to early_init_transmeta()
x86: identify_cpu_without_cpuid v2
x86: extended "flags" to show virtualization HW feature in /proc/cpuinfo
x86: move VMX MSRs to msr-index.h
x86: centaur_64.c remove duplicated setting of CONSTANT_TSC
x86: intel.c put workaround for old cpus together
x86: let intel 64-bit use intel.c
x86: make intel_64.c the same as intel.c
x86: make intel.c have 64-bit support code
x86: little clean up of intel.c/intel_64.c
x86: make 64 bit to use amd.c
x86: make amd_64 have 32 bit code
x86: make amd.c have 64bit support code
x86: merge header in amd_64.c
x86: add srat_detect_node for amd64
x86: remove duplicated force_mwait
x86: cpu make amd.c more like amd_64.c v2
...
* 'x86-v28-for-linus-phase3-B' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (74 commits)
AMD IOMMU: use iommu_device_max_index, fix
AMD IOMMU: use iommu_device_max_index
x86: add PCI IDs for AMD Barcelona PCI devices
x86/iommu: use __GFP_ZERO instead of memset for GART
x86/iommu: convert GART need_flush to bool
x86/iommu: make GART driver checkpatch clean
x86 gart: remove unnecessary initialization
x86: restore old GART alloc_coherent behavior
revert "x86: make GART to respect device's dma_mask about virtual mappings"
x86: export pci-nommu's alloc_coherent
iommu: remove fullflush and nofullflush in IOMMU generic option
x86: remove set_bit_string()
iommu: export iommu_area_reserve helper function
AMD IOMMU: use coherent_dma_mask in alloc_coherent
add AMD IOMMU tree to MAINTAINERS file
AMD IOMMU: use cmd_buf_size when freeing the command buffer
AMD IOMMU: calculate IVHD size with a function
AMD IOMMU: remove unnecessary cast to u64 in the init code
AMD IOMMU: free domain bitmap with its allocation order
AMD IOMMU: simplify dma_mask_to_pages
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1075 commits)
myri10ge: update driver version number to 1.4.3-1.369
r8169: add shutdown handler
r8169: preliminary 8168d support
r8169: support additional 8168cp chipset
r8169: change default behavior for mildly identified 8168c chipsets
r8169: add a new 8168cp flavor
r8169: add a new 8168c flavor (bis)
r8169: add a new 8168c flavor
r8169: sync existing 8168 device hardware start sequences with vendor driver
r8169: 8168b Tx performance tweak
r8169: make room for more specific 8168 hardware start procedure
r8169: shuffle some registers handling around (8168 operation only)
r8169: new phy init parameters for the 8168b
r8169: update phy init parameters
r8169: wake up the PHY of the 8168
af_key: fix SADB_X_SPDDELETE response
ath9k: Fix return code when ath9k_hw_setpower() fails on reset
ath9k: remove nasty FAIL macro from ath9k_hw_reset()
gre: minor cleanups in netlink interface
gre: fix copy and paste error
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (49 commits)
MIPS: RB532: provide GPIO_BUILTIN_NR and irq_to_gpio/gpio_to_irq
MIPS: Move ptrace prototypes to ptrace.h
MIPS: Ptrace support for HARDWARE_WATCHPOINTS
MIPS: Scheduler support for HARDWARE_WATCHPOINTS.
MIPS: Watch exception handling for HARDWARE_WATCHPOINTS.
MIPS: Probe watch registers and report configuration.
MIPS: Add HARDWARE_WATCHPOINTS definitions and support code.
MIPS: Add HARDWARE_WATCHPOINTS configure option.
MIPS: Replace use of <asm-generic/uaccess.h> with native implementations.
MIPS: TXx9: Add TX4939 ATA support (v2)
MIPS: Rewrite spinlocks to ticket locks.
MIPS: IP checksums: Optimize adjust of sum on buffers of odd alignment.
MIPS: IP checksums: Remove unncessary .set pseudos
MIPS: IP checksums: Remove unncessary folding of sum to 16 bit.
MIPS: Move headfiles to new location below arch/mips/include
MIPS: Alchemy: rename directory
MIPS: Optimize get_user and put_user for 64-bit
MIPS: TXx9: Implement prom_free_prom_memory
MIPS: TXx9: Add RBTX4939 board support
MIPS: TXx9: Add TX4939 SoC support
...
* 'for-linus' of git://git.alsa-project.org/alsa-kernel: (258 commits)
ALSA: hda: VREF powerdown for headphones
ALSA: hda: STAC_HP_M4
ALSA: ASoC: Check for machine type in GTA01 machine driver
ALSA: mtpav - Fix race in probe
ALSA: usb-audio: dynamic detection of MIDI interfaces in uaxx-quirk
ALSA: Add a note on dependency of RTC stuff
ALSA: ASoC: add new param mux to dapm_mux_update_power
ALSA: Increase components array size
ALSA: ASoC: Correct inverted Mic PGA Switch control in wm8510 driver
ALSA: hda: comment typo fix
ALSA: hda: comment typo fix
ALSA: hda - Fix PCI SSID for ASROCK K18N78FullHD-hSLI
ALSA: snd-usb-audio: support for Edirol UA-4FX device
ALSA: usb - Fix possible Oops at USB-MIDI disconnection
ALSA: hda - Fix another ALC889A (rev 0x100101)
ALSA: hda: add more board-specific information for Realtek ALC662 rev1
ALSA: Correct Vladimir Barinov's e-mail address
ALSA: cs46xx: Add PCI IDs for TerraTec and Hercules cards
ALSA: hda: SPDIF stream muting support
ALSA: hda: appletv support
...
The Routerboard 532 bootloader passes the korina ethernet
MAC adapter address to the kernel on the command line.
Document this in the kernel-parameters file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds the core function pnp_dbg() and a new config option to
enable it.
The PNP core debugging messages can be enabled at boot-time with the
"pnp.debug" kernel parameter.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If the journal doesn't abort when it gets an IO error in file data
blocks, the file data corruption will spread silently. Because
most of applications and commands do buffered writes without fsync(),
they don't notice the IO error. It's scary for mission critical
systems. On the other hand, if the journal aborts whenever it gets
an IO error in file data blocks, the system will easily become
inoperable. So this patch introduces a filesystem option to
determine whether it aborts the journal or just call printk() when
it gets an IO error in file data.
If you mount an ext4 fs with data_err=abort option, it aborts on file
data write error. If you mount it with data_err=ignore, it doesn't
abort, just call printk(). data_err=ignore is the default.
Here is the corresponding patch of the ext3 version:
http://kerneltrap.org/mailarchive/linux-kernel/2008/9/9/3239374
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The ext4 filesystem is getting stable enough that it's time to drop
the "dev" prefix. Also remove the requirement for the TEST_FILESYS
flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We need to add a flag for all code that is in the drivers/staging/
directory to prevent all other kernel developers from worrying about
issues here, and to notify users that the drivers might not be as good
as they are normally used to.
Based on code from Andreas Gruenbacher and Jeff Mahoney to provide a
TAINT flag for the support level of a kernel module in the Novell
enterprise kernel release.
This is the kernel portion of this feature, the ability for the flag to
be set needs to be done in the build process and will happen in a
follow-up patch.
Cc: Andreas Gruenbacher <agruen@suse.de>
Cc: Jeff Mahoney <jeffm@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'rcu-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (21 commits)
rcu: RCU-based detection of stalled CPUs for Classic RCU, fix
rcu: RCU-based detection of stalled CPUs for Classic RCU
rcu: add rcu_read_lock_sched() / rcu_read_unlock_sched()
rcu: fix sparse shadowed variable warning
doc/RCU: fix pseudocode in rcuref.txt
rcuclassic: fix compiler warning
rcu: use irq-safe locks
rcuclassic: fix compilation NG
rcu: fix locking cleanup fallout
rcu: remove redundant ACCESS_ONCE definition from rcupreempt.c
rcu: fix classic RCU locking cleanup lockdep problem
rcu: trace fix possible mem-leak
rcu: just rename call_rcu_bh instead of making it a macro
rcu: remove list_for_each_rcu()
rcu: fixes to include/linux/rcupreempt.h
rcu: classic RCU locking and memory-barrier cleanups
rcu: prevent console flood when one CPU sees another AWOL via RCU
rcu, debug: detect stalled grace periods, cleanups
rcu, debug: detect stalled grace periods
rcu classic: new algorithm for callbacks-processing(v2)
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
selinux: Fix an uninitialized variable BUG/panic in selinux_secattr_to_sid()
selinux: use default proc sid on symlinks
file capabilities: uninline cap_safe_nice
Update selinux info in MAINTAINERS and Kconfig help text
SELinux: add gitignore file for mdp script
SELinux: add boundary support and thread context assignment
securityfs: do not depend on CONFIG_SECURITY
selinux: add support for installing a dummy policy (v2)
security: add/fix security kernel-doc
selinux: Unify for- and while-loop style
selinux: conditional expression type validation was off-by-one
smack: limit privilege by label
SELinux: Fix a potentially uninitialised variable in SELinux hooks
SELinux: trivial, remove unneeded local variable
SELinux: Trivial minor fixes that change C null character style
make selinux_write_opts() static
* 'sched-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (38 commits)
sched debug: add name to sched_domain sysctl entries
sched: sync wakeups vs avg_overlap
sched: remove redundant code in cpu_cgroup_create()
sched_rt.c: resch needed in rt_rq_enqueue() for the root rt_rq
cpusets: scan_for_empty_cpusets(), cpuset doesn't seem to be so const
sched: minor optimizations in wake_affine and select_task_rq_fair
sched: maintain only task entities in cfs_rq->tasks list
sched: fixup buddy selection
sched: more sanity checks on the bandwidth settings
sched: add some comments to the bandwidth code
sched: fixlet for group load balance
sched: rework wakeup preemption
CFS scheduler: documentation about scheduling policies
sched: clarify ifdef tangle
sched: fix list traversal to use _rcu variant
sched: turn off WAKEUP_OVERLAP
sched: wakeup preempt when small overlap
kernel/cpu.c: create a CPU_STARTING cpu_chain notifier
kernel/cpu.c: Move the CPU_DYING notifiers
sched: fix __load_balance_iterator() for cfq with only one task
...
Add documentation for the new "purge" cio_ignore parameter.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (37 commits)
[SCSI] zfcp: fix double dbf id usage
[SCSI] zfcp: wait on SCSI work to be finished before proceeding with init dev
[SCSI] zfcp: fix erp list usage without using locks
[SCSI] zfcp: prevent fc_remote_port_delete calls for unregistered rport
[SCSI] zfcp: fix deadlock caused by shared work queue tasks
[SCSI] zfcp: put threshold data in hba trace
[SCSI] zfcp: Simplify zfcp data structures
[SCSI] zfcp: Simplify get_adapter_by_busid
[SCSI] zfcp: remove all typedefs and replace them with standards
[SCSI] zfcp: attach and release SAN nameserver port on demand
[SCSI] zfcp: remove unused references, declarations and flags
[SCSI] zfcp: Update message with input from review
[SCSI] zfcp: add queue_full sysfs attribute
[SCSI] scsi_dh: suppress comparison warning
[SCSI] scsi_dh: add Dell product information into rdac device handler
[SCSI] qla2xxx: remove the unused SCSI_QLOGIC_FC_FIRMWARE option
[SCSI] qla2xxx: fix printk format warnings
[SCSI] qla2xxx: Update version number to 8.02.01-k8.
[SCSI] qla2xxx: Ignore payload reserved-bits during RSCN processing.
[SCSI] qla2xxx: Additional residual-count corrections during UNDERRUN handling.
...
* 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block: (132 commits)
doc/cdrom: Trvial documentation error, file not present
block_dev: fix kernel-doc in new functions
block: add some comments around the bio read-write flags
block: mark bio_split_pool static
block: Find bio sector offset given idx and offset
block: gendisk integrity wrapper
block: Switch blk_integrity_compare from bdev to gendisk
block: Fix double put in blk_integrity_unregister
block: Introduce integrity data ownership flag
block: revert part of d7533ad0e132f92e75c1b2eb7c26387b25a583c1
bio.h: Remove unused conditional code
block: remove end_{queued|dequeued}_request()
block: change elevator to use __blk_end_request()
gdrom: change to use __blk_end_request()
memstick: change to use __blk_end_request()
virtio_blk: change to use __blk_end_request()
blktrace: use BLKTRACE_BDEV_SIZE as the name size for setup structure
block: add lld busy state exporting interface
block: Fix blk_start_queueing() to not kick a stopped queue
include blktrace_api.h in headers_install
...
This merges phase 1 of the x86 tree, which is a collection of branches:
x86/alternatives, x86/cleanups, x86/commandline, x86/crashdump,
x86/debug, x86/defconfig, x86/doc, x86/exports, x86/fpu, x86/gart,
x86/idle, x86/mm, x86/mtrr, x86/nmi-watchdog, x86/oprofile,
x86/paravirt, x86/reboot, x86/sparse-fixes, x86/tsc, x86/urgent and
x86/vmalloc
and as Ingo says: "these are the easiest, purely independent x86 topics
with no conflicts, in one nice Octopus merge".
* 'x86-v28-for-linus-phase1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (147 commits)
x86: mtrr_cleanup: treat WRPROT as UNCACHEABLE
x86: mtrr_cleanup: first 1M may be covered in var mtrrs
x86: mtrr_cleanup: print out correct type v2
x86: trivial printk fix in efi.c
x86, debug: mtrr_cleanup print out var mtrr before change it
x86: mtrr_cleanup try gran_size to less than 1M, v3
x86: mtrr_cleanup try gran_size to less than 1M, cleanup
x86: change MTRR_SANITIZER to def_bool y
x86, debug printouts: IOMMU setup failures should not be KERN_ERR
x86: export set_memory_ro and set_memory_rw
x86: mtrr_cleanup try gran_size to less than 1M
x86: mtrr_cleanup prepare to make gran_size to less 1M
x86: mtrr_cleanup safe to get more spare regs now
x86_64: be less annoying on boot, v2
x86: mtrr_cleanup hole size should be less than half of chunk_size, v2
x86: add mtrr_cleanup_debug command line
x86: mtrr_cleanup optimization, v2
x86: don't need to go to chunksize to 4G
x86_64: be less annoying on boot
x86, olpc: fix endian bug in openfirmware workaround
...
The sbpcd tester program is not included in the kernel source tree,
so remove the reference to it.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Nick Warne <nick@ukfsn.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
After commit 831830b5a2 aka
"restrict reading from /proc/<pid>/maps to those who share ->mm or can ptrace"
sysctl stopped being relevant because commit moved security checks from ->show
time to ->start time (mm_for_maps()).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Kees Cook <kees.cook@canonical.com>
Replace the no longer working links and email address in the
documentation and in source code.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Dave Jones <davej@redhat.com>
Describe the sysfs files that were introduced in the ibmaem driver.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This example isn't the proper way to handle scatterlists (can't handle
sg chaining).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Update the description of fifo_batch to match the current implementation,
and include a description of how to tune it.
Signed-off-by: Aaron Carroll <aaronc@gelato.unsw.edu.au>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
These are now replaced by the rfkill interface.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
This updates xt_recent to support the IPv6 address family.
The new /proc/net/xt_recent directory must be used for this.
The old proc interface can also be configured out.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Documentation/powerpc/smp.txt is so outdated that it makes sense to just
remove it.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit 14cf11af6c ("powerpc: Merge enough to
start building in arch/powerpc.") unwired /proc/ppc_htab, and commit
917f0af9e5 ("powerpc: Remove arch/ppc and
include/asm-ppc") removed the rest of the /proc/ppc_htab support, but there are
still a few references left. Kill them for good.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (33 commits)
V4L/DVB (9103): em28xx: HVR-900 B3C0 - fix audio clicking issue
V4L/DVB (9099): em28xx: Add detection for K-WORLD DVB-T 310U
V4L/DVB (9092): gspca: Bad init values for sonixj ov7660.
V4L/DVB (9080): gspca: Add a delay after writing to the sonixj sensors.
V4L/DVB (9075): gspca: Bad check of returned status in i2c_read() spca561.
V4L/DVB (9053): fix buffer overflow in uvc-video
V4L/DVB (9043): S5H1420: Fix size of shadow-array to avoid overflow
V4L/DVB (9037): Fix support for Hauppauge Nova-S SE
V4L/DVB (9029): Fix deadlock in demux code
V4L/DVB (8979): sms1xxx: Add new USB product ID for Hauppauge WinTV MiniStick
V4L/DVB (8978): sms1xxx: fix product name for Hauppauge WinTV MiniStick
V4L/DVB (8967): Use correct XC3028L firmware for AMD ATI TV Wonder 600
V4L/DVB (8963): s2255drv field count fix
V4L/DVB (8961): zr36067: Fix RGBR pixel format
V4L/DVB (8960): drivers/media/video/cafe_ccic.c needs mm.h
V4L/DVB (8958): zr36067: Return proper bytes-per-line value
V4L/DVB (8957): zr36067: Restore the default pixel format
V4L/DVB (8955): bttv: Prevent NULL pointer dereference in radio_open
V4L/DVB (8935): em28xx-cards: Remove duplicate entry (EM2800_BOARD_KWORLD_USB2800)
V4L/DVB (8933): gspca: Disable light frquency for zc3xx cs2102 Kokom.
...
Correct firmware type to MTS
Correct audio routing for composite/s-video
Add DVB-T detection.
This patch uses the eeprom hash method for detection as the vendor/product
ids are also used for the DIGIVOX_AD. This may be a clone of the same
product. Explanatory text has been added prior to the hask look-up in
anticipation that it may help others.
The following has been tested to work:
Analogue TV (PAL-I)
Composite In
DVB-T (UK Crystal Palace)
USB AUDIO
The following has not been tested but probably works:
S-Video In
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The "Documentation" section of this file mentions that when an interface
change is made, I should be CCed with info about the change (so that
man-pages can document it). Additionally request that this info be CCed
to the new linux-api@vger.kernel.org list.
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mention that patches that change the kernel-userland interface should
be CCed to the new list linux-api@vger.kernel.org.
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Basic vfs-level fiemap infrastructure, which sets up a new ->fiemap
inode operation.
Userspace can get extent information on a file via fiemap ioctl. As input,
the fiemap ioctl takes a struct fiemap which includes an array of struct
fiemap_extent (fm_extents). Size of the extent array is passed as
fm_extent_count and number of extents returned will be written into
fm_mapped_extents. Offset and length fields on the fiemap structure
(fm_start, fm_length) describe a logical range which will be searched for
extents. All extents returned will at least partially contain this range.
The actual extent offsets and ranges returned will be unmodified from their
offset and range on-disk.
The fiemap ioctl returns '0' on success. On error, -1 is returned and errno
is set. If errno is equal to EBADR, then fm_flags will contain those flags
which were passed in which the kernel did not understand. On all other
errors, the contents of fm_extents is undefined.
As fiemap evolved, there have been many authors of the vfs patch. As far as
I can tell, the list includes:
Kalpak Shah <kalpak.shah@sun.com>
Andreas Dilger <adilger@sun.com>
Eric Sandeen <sandeen@redhat.com>
Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: linux-api@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
With modern hard drives, reading 64k takes roughly the same time as
reading a 4k block. So request readahead for adjacent inode table
blocks to reduce the time it takes when iterating over directories
(especially when doing this in htree sort order) in a cold cache case.
With this patch, the time it takes to run "git status" on a kernel
tree after flushing the caches via "echo 3 > /proc/sys/vm/drop_caches"
is reduced by 21%.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There's already a fc_vport_termintate() call exported by
the transport. This patch adds a symmetric call to the API to allow
an NPIV-capable LLD to instantiate vports sans user intervention.
Additional comments/updates:
Re: scsi_fc_transport.txt
Add a function prototype for fc_vport_terminate similar to what's
done for fc_vport_create
Re: fc_vport_create
I recommend we pass the channel number in fc_vport_create rather
than fixing it at zero.
Also, ids->vport_type should be set to FC_PORTTYPE_NPIV prior to
calling fc_vport_create. The comment is also meaningless.
Added-by and
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix grammar errors spotted by Randy Dunlap,
and adds some more details.
Signed-off-by: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UBIFS read performance can be improved by skipping the CRC
check when data nodes are read. This option can be used if
the underlying media is considered to be highly reliable.
Note that CRCs are always checked for metadata.
Read speed on Arm platform with OneNAND goes from 19 MiB/s
to 27 MiB/s with data CRC checking disabled.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Some flash media are capable of reading sequentially at faster rates.
UBIFS bulk-read facility is designed to take advantage of that, by
reading in one go consecutive data nodes that are also located
consecutively in the same LEB.
Read speed on Arm platform with OneNAND goes from 17 MiB/s to
19 MiB/s.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Correct copy-paste problem: CDROMCLOSETRAY is about closing the tray,
not opening it.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Due to recent patches removing the now deprecated references to
{set,reset}_scoop_gpio() and converting them to the generic GPIO
API, the references in the documentation also need to be fixed.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Liam Girdwood <lrg@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a usage documentation for the virtual CAN driver (vcan).
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Structured similar to the existing QE GPIO support.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the example code consistent with changed API.
Signed-off-by: Marin Mitov <mitov@ispp.bas.bg>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The documentation about the CFS scheduler is scarse when it comes to
scheduling policies. This patch adds a chapter about the scheduling
policies it supports. Peter Zijlstra provided most of the information
for it in
http://marc.info/?l=linux-kernel&m=122210038326356&w=2
Signed-off-by: Martin Steigerwald <ms@teamix.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch against tip/x86/iommu virtually reverts
2842e5bf31. But just reverting the
commit breaks AMD IOMMU so this patch also includes some fixes.
The above commit adds new two options to x86 IOMMU generic kernel boot
options, fullflush and nofullflush. But such change that affects all
the IOMMUs needs more discussion (all IOMMU parties need the chance to
discuss it):
http://lkml.org/lkml/2008/9/19/106
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The GART currently implements the iommu=[no]fullflush command line
parameters which influence its IO/TLB flushing strategy. This patch
makes these parameters generic so that they can be used by the AMD IOMMU
too.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add the fsl,playback-dma and fsl,capture-dma properties to the Freescale
MPC8610 HPCD device tree. These properties connect the SSI nodes to the
DMA nodes for the DMA channels that the SSI should use. Also update the
ssi.txt documentation.
These properties will be needed when the ASoC V2 version of the Freescale
MPC8610 device drivers are merged into the mainline.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simplify the sysfs ABI of the wusb-cbaf (Cable Based Association)
driver: use one value per file and cause the write of the CHID to
fetch the CDID (instead of requiring a separate read).
Update the example wusb-cbaf script to work with this revised ABI.
Signed-off-by: Felipe Zimmerle <felipe.zimmerle@indt.org.br>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Documentation (and example utilities) for the UWB (and WUSB) stacks.
Some of the documentation may be out-of-date.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
A few errors sneaked in over time, some functions no longer exist,
for some alternatives exist. This changes the docbook template to
include the right things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, rfkill would stand in the way of properly supporting wireless
devices that are capable of waking the system up from sleep or hibernation
when they receive a special wireless message. It would also get in the way
of mesh devices that need to remain operational even during platform
suspend.
To avoid that, stop trying to block the transmitters on the rfkill class
suspend handler.
Drivers that need rfkill's older behaviour will have to implement it by
themselves in their own suspend handling.
Do note that rfkill *will* attempt to restore the transmitter state on
resume in any situation. This happens after the driver's resume method is
called by the suspend core (class devices resume after the devices they are
attached to have been resumed).
The following drivers need to check if they need to explicitly block
their transmitters in their own suspend handlers (maintainers Cc'd):
arch/arm/mach-pxa/tosa-bt.c
drivers/net/usb/hso.c
drivers/net/wireless/rt2x00/* (USB might need it?)
drivers/net/wireless/b43/ (SSB over USB might need it?)
drivers/misc/hp-wmi.c
eeepc-laptop w/rfkill support (not in mainline yet)
Compal laptop w/rfkill support (not in mainline yet)
toshiba-acpi w/rfkill support (not in mainline yet)
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Andrew Bird <ajb@spheresystems.co.uk>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the new wireless regulatory infrastructure. The
main motiviation behind this was to centralize regulatory
code as each driver was implementing their own regulatory solution,
and to replace the initial centralized code we have where:
* only 3 regulatory domains are supported: US, JP and EU
* regulatory domains can only be changed through module parameter
* all rules were built statically in the kernel
We now have support for regulatory domains for many countries
and regulatory domains are now queried through a userspace agent
through udev allowing distributions to update regulatory rules
without updating the kernel.
Each driver can regulatory_hint() a regulatory domain
based on either their EEPROM mapped regulatory domain value to a
respective ISO/IEC 3166-1 country code or pass an internally built
regulatory domain. We also add support to let the user set the
regulatory domain through userspace in case of faulty EEPROMs to
further help compliance.
Support for world roaming will be added soon for cards capable of
this.
For more information see:
http://wireless.kernel.org/en/developers/Regulatory/CRDA
For now we leave an option to enable the old module parameter,
ieee80211_regdom, and to build the 3 old regdomains statically
(US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY.
These old static definitions and the module parameter is being
scheduled for removal for 2.6.29. Note that if you use this
you won't make use of a world regulatory domain as its pointless.
If you leave this option enabled and if CRDA is present and you
use US or JP we will try to ask CRDA to update us a regulatory
domain for us.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide summary ABI docs about the /sys/class/gpio files.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no description of bit 4 of coredump_filter in the
documentation. This patch adds it.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If all the cpus in a cpuset are offlined, the tasks in it will be moved to
the nearest ancestor with non-empty cpus.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Jackson <pj@sgi.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch resolves a few issues found with multiq including wording
suggestions and a problem seen in the allocation of queues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new action will have the ability to change the priority and/or
queue_mapping fields on an sk_buff.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is intended to add a qdisc to support the new tx multiqueue
architecture by providing a band for each hardware queue. By doing
this it is possible to support a different qdisc per physical hardware
queue.
This qdisc uses the skb->queue_mapping to select which band to place
the traffic onto. It then uses a round robin w/ a check to see if the
subqueue is stopped to determine which band to dequeue the packet from.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atomic_inc_not_zero(v) return 0 if *v = 0.
use spin_lock instead of write_lock for update lock.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the 2.6.27 circle ->fasync lost the BKL, and the last remaining
->open variant that takes the BKL is also gone. ->get_sb and ->kill_sb
didn't have BKL forever, so updated the entries while we're at that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The corruption check is enabled in Kconfig by default, but disabled at runtime.
This patch adds several kernel parameters to control the corruption
check's behaviour; these are documented in kernel-parameters.txt.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some BIOSes have been observed to corrupt memory in the low 64k. This
change:
- Reserves all memory which does not have to be in that area, to
prevent it from being used as general memory by the kernel. Things
like the SMP trampoline are still in the memory, however.
- Clears the reserved memory so we can observe changes to it.
- Adds a function check_for_bios_corruption() which checks and reports on
memory becoming unexpectedly non-zero. Currently it's called in the
x86 fault handler, and the powermanagement debug output.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (98 commits)
V4L/DVB (8881): gspca: After 'while (retry--) {...}', retry will be -1 but not 0.
V4L/DVB (8880): PATCH: Fix parents on some webcam drivers
V4L/DVB (8877): b2c2 and bt8xx: udelay to mdelay
V4L/DVB (8876): budget: udelay changed to mdelay
V4L/DVB (8874): gspca: Adjust hstart for sn9c103/ov7630 and update usb-id's.
V4L/DVB (8873): gspca: Bad image offset with rev012a of spca561 and adjust exposure.
V4L/DVB (8872): gspca: Bad image format and offset with rev072a of spca561.
V4L/DVB (8870): gspca: Fix dark room problem with sonixb.
V4L/DVB (8869): gspca: Move the Sonix webcams with TAS5110C1B from sn9c102 to gspca.
V4L/DVB (8868): gspca: Support for vga modes with sif sensors in sonixb.
V4L/DVB (8844): dabusb_fpga_download(): fix a memory leak
V4L/DVB (8843): tda10048_firmware_upload(): fix a memory leak
V4L/DVB (8842): vivi_release(): fix use-after-free
V4L/DVB (8840): dib0700: add basic support for Hauppauge Nova-TD-500 (84xxx)
V4L/DVB (8839): dib0700: add comment to identify 35th USB id pair
V4L/DVB (8837): dvb: fix I2C adapters name size
V4L/DVB (8835): gspca: Same pixfmt as the sn9c102 driver and raw Bayer added in sonixb.
V4L/DVB (8834): gspca: Have a bigger buffer for sn9c10x compressed images.
V4L/DVB (8833): gspca: Cleanup the sonixb code.
V4L/DVB (8832): gspca: Bad pixelformat of vc0321 webcams.
...
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6:
acer-wmi: remove debugfs entries upon unloading
ACPI: Avoid bogus timeout about SMbus check
fujitsu-laptop: fix regression for P8010 in 2.6.27-rc
ACPI: Make Len Brown the ACPI maintainer again
ACPI: thinkpad-acpi: wan radio control is not experimental
PNPACPI: ignore the producer/consumer bit for extended IRQ descriptors
acpi: add checking for NULL early param
ACPI: Fix typo in "Disable MWAIT via DMI on broken Compal board"
ACPI: Fix now signed module parameter.
ACPI: Change package length error to warning
ACPI: Fix now signed module parameter.
As noted by Gu Rui in http://bugzilla.kernel.org/show_bug.cgi?id=11444,
there is a typo in Documentation/sound/alsa/ALSA-Configuration.txt.
After checking the source (sound/pci/hda/hda_intel.c), the report
looks correct to me.
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds a generic infrastructure for policy-based dequeueing of
TX packets and provides two policies:
* a simple FIFO policy (which is the default) and
* a priority based policy (set via socket options).
Both policies honour the tx_qlen sysctl for the maximum size of the write
queue (can be overridden via socket options).
The priority policy uses skb->priority internally to assign an u32 priority
identifier, using the same ranking as SO_PRIORITY. The skb->priority field
is set to 0 when the packet leaves DCCP. The priority is supplied as ancillary
data using cmsg(3), the patch also provides the requisite parsing routines.
Signed-off-by: Tomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This adds full support for local/remote Sequence Window feature, from which the
* sequence-number-validity (W) and
* acknowledgment-number-validity (W') windows
derive as specified in RFC 4340, 7.5.3.
Specifically, the following changes are introduced:
* integrated new socket fields into dccp_sk;
* updated the update_gsr/gss routines with regard to these fields;
* updated handler code: the Sequence Window feature is located at the TX side,
so the local feature is meant if the handler-rx flag is false;
* the initialisation of `rcv_wnd' in reqsk is removed, since
- rcv_wnd is not used by the code anywhere;
- sequence number checks are not done in the LISTEN state (cf. 7.5.3);
- dccp_check_req checks the Ack number validity more rigorously;
* the `struct dccp_minisock' became empty and is now removed.
Until the handshake completes with activating negotiated values, the local/remote
Sequence-Window values are undefined and thus can not reliably be estimated.
This issue is addressed in a separate patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This removes the use of the sysctl and the minisock variable for the Send Ack
Vector feature, which is now handled fully dynamically via feature negotiation;
i.e. when CCID2 is enabled, Ack Vectors are automatically enabled (as per
RFC 4341, 4.).
Using a sysctl in parallel to this implementation would open the door to
crashes, since much of the code relies on tests of the boolean minisock /
sysctl variable. Thus, this patch replaces all tests of type
if (dccp_msk(sk)->dccpms_send_ack_vector)
/* ... */
with
if (dp->dccps_hc_rx_ackvec != NULL)
/* ... */
The dccps_hc_rx_ackvec is allocated by the dccp_hdlr_ackvec() when feature
negotiation concluded that Ack Vectors are to be used on the half-connection.
Otherwise, it is NULL (due to dccp_init_sock/dccp_create_openreq_child),
so that the test is a valid one.
The activation handler for Ack Vectors is called as soon as the feature
negotiation has concluded at the
* server when the Ack marking the transition RESPOND => OPEN arrives;
* client after it has sent its ACK, marking the transition REQUEST => PARTOPEN.
Adding the sequence number of the Response packet to the Ack Vector has been
removed, since
(a) connection establishment implies that the Response has been received;
(b) the CCIDs only look at packets received in the (PART)OPEN state, i.e.
this entry will always be ignored;
(c) it can not be used for anything useful - to detect loss for instance, only
packets received after the loss can serve as pseudo-dupacks.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Updating the NDP count feature is handled automatically now:
* for CCID-2 it is disabled, since the code does not use NDP counts;
* for CCID-3 it is enabled, as NDP counts are used to determine loss lengths.
Allowing the user to change NDP values leads to unpredictable and failing
behaviour, since it is then possible to disable NDP counts even when they
are needed (e.g. in CCID-3).
This means that only those user settings are sensible that agree with the
values for Send NDP Count implied by the choice of CCID. But those settings
are already activated by the feature negotiation (CCID dependency tracking),
hence this form of support is redundant.
At startup the initialisation of the NDP count feature is with the default
value of 0, which is done implicitly by the zeroing-out of the socket when
it is allocated. If the choice of CCID or feature negotiation enables NDP
count, this will then be updated via the NDP activation handler.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
The TX/RX CCIDs of the minisock are now redundant: similar to the Ack Vector
case, their value equals initially that of the sysctl, but at the end of
feature negotiation may be something different.
The old interface removed by this patch thus has been replaced by the newer
interface to dynamically query the currently loaded CCIDs earlier in this
patch set.
Also removed the constructors for the TX CCID and the RX CCID, since the
switch rx/non-rx is done by the handler in minisocks.c (and the handler is
the only place in the code where CCIDs are loaded).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
With this patch, TX/RX CCIDs can now be changed on a per-connection basis, which
overrides the defaults set by the global sysctl variables for TX/RX CCIDs.
To make full use of this facility, the remaining patches of this patch set are
needed, which track dependencies and activate negotiated feature values.
Note on the maximum number of CCIDs that can be registered:
-----------------------------------------------------------
The maximum number of CCIDs that can be registered on the socket is constrained
by the space in a Confirm/Change feature negotiation option.
The space in these in turn depends on the size of header options as defined
in RFC 4340, 5.8. Since this is a recurring constant, it has been moved from
ackvec.h into linux/dccp.h, clarifying its purpose.
Relative to this size, the maximum number of CCID identifiers that can be
present in a Confirm option (which always consumes 1 byte more than a Change
option, cf. 6.1) is 2 bytes less than the maximum TLV size: one for the
CCID-feature-type and one for the selected value.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch deprecates the Ack Ratio sysctl, since
* Ack Ratio is entirely ignored by CCID-3 and CCID-4,
* Ack Ratio currently doesn't work in CCID-2 (i.e. is always set to 1);
* even if it would work in CCID-2, there is no point for a user to change it:
- Ack Ratio is constrained by cwnd (RFC 4341, 6.1.2),
- if Ack Ratio > cwnd, the system resorts to spurious RTO timeouts
(since waiting for Acks which will never arrive in this window),
- cwnd is not a user-configurable value.
The only reasonable place for Ack Ratio is to print it for debugging. It is
planned to do this later on, as part of e.g. dccp_probe.
With this patch Ack Ratio is now under full control of feature negotiation:
* Ack Ratio is resolved as a dependency of the selected CCID;
* if the chosen CCID supports it (i.e. CCID == CCID-2), Ack Ratio is set to
the default of 2, following RFC 4340, 11.3 - "New connections start with Ack
Ratio 2 for both endpoints";
* what happens then is part of another patch set, since it concerns the
dynamic update of Ack Ratio while the connection is in full flight.
Thanks to Tomasz Grobelny for discussion leading up to this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This provides a data structure to record which CCIDs are locally supported
and three accessor functions:
- a test function for internal use which is used to validate CCID requests
made by the user;
- a copy function so that the list can be used for feature-negotiation;
- documented getsockopt() support so that the user can query capabilities.
The data structure is a table which is filled in at compile-time with the
list of available CCIDs (which in turn depends on the Kconfig choices).
Using the copy function for cloning the list of supported CCIDs is useful for
feature negotiation, since the negotiation is now with the full list of available
CCIDs (e.g. {2, 3}) instead of the default value {2}. This means negotiation
will not fail if the peer requests to use CCID3 instead of CCID2.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
-Add usb id for 093a:2624 (pac7302)
-Report some controls to userspace with 7302 only, as they are 7302 only
-Add gain and exposure controls
-Add autogain
-Fix 7302 imaged being mirrored by default
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch adapted from a patch to gspcav1 made by the google microdia group.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update Documentation/filesystems/proc.txt: it describes the file
auto_msgmni intoduced to enable/disable msgmni automatic recomputing upon
memory add/remove (see thread http://lkml.org/lkml/2008/7/4/27). Also
added a description for msgmni (this filex is only listed in
Documentation/sysctl/kernel.txt).
Signed-off-by: Nadia Derbey <Nadia.Derbey@bull.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the location of the NTFS homepage in several files.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the new firmware infrastructure in 2.6.27, some files are generated and shouldn't be
diffed; add these 2 to the "dontdiff" file
Signed-off-by: Arjan van de Ven <arjan@Linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added the support of Toshiba RX1 laptop with ALC262 codec chip.
Related ALSA bug#3386:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3386
Signed-off-by: Hiroshi Miura <miurahr@acm.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the descriptions of missing model values.
Also, fixed the model strings of a few new models to a standard style.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The WWAN radio control has been working well for over three years,
and is no longer experimental.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Commit ecd29476ae removed the
"disable_8254_timer" and "enable_8254_timer" kernel parameters from
the kernel but did not remove the references to them from two
files in the Documentation directory: kernel-parameters.txt and
x86/x86_64/boot-options.txt.
This change completes the removal.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In August 2006 I posted a patch generating a minimal SELinux policy. This
week, David P. Quigley posted an updated version of that as a patch against
the kernel. It also had nice logic for auto-installing the policy.
Following is David's original patch intro (preserved especially
bc it has stats on the generated policies):
se interested in the changes there were only two significant
changes. The first is that the iteration through the list of classes
used NULL as a sentinel value. The problem with this is that the
class_to_string array actually has NULL entries in its table as place
holders for the user space object classes.
The second change was that it would seem at some point the initial sids
table was NULL terminated. This is no longer the case so that iteration
has to be done on array length instead of looking for NULL.
Some statistics on the policy that it generates:
The policy consists of 523 lines which contain no blank lines. Of those
523 lines 453 of them are class, permission, and initial sid
definitions. These lines are usually little to no concern to the policy
developer since they will not be adding object classes or permissions.
Of the remaining 70 lines there is one type, one role, and one user
statement. The remaining lines are broken into three portions. The first
group are TE allow rules which make up 29 of the remaining lines, the
second is assignment of labels to the initial sids which consist of 27
lines, and file system labeling statements which are the remaining 11.
In addition to the policy.conf generated there is a single file_contexts
file containing two lines which labels the entire system with base_t.
This policy generates a policy.23 binary that is 7920 bytes.
(then a few versions later...):
The new policy is 587 lines (stripped of blank lines) with 476 of those
lines being the boilerplate that I mentioned last time. The remaining
111 lines have the 3 lines for type, user, and role, 70 lines for the
allow rules (one for each object class including user space object
classes), 27 lines to assign types to the initial sids, and 11 lines for
file system labeling. The policy binary is 9194 bytes.
Changelog:
Aug 26: Added Documentation/SELinux.txt
Aug 26: Incorporated a set of comments by Stephen Smalley:
1. auto-setup SELINUXTYPE=dummy
2. don't auto-install if selinux is enabled with
non-dummy policy
3. don't re-compute policy version
4. /sbin/setfiles not /usr/sbin/setfiles
Aug 22: As per JMorris comments, made sure make distclean
cleans up the mdp directory.
Removed a check for file_contexts which is now
created in the same file as the check, making it
superfluous.
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
This patch adds kernel doc for the completion feature.
An error in the split-man.pl PERL snippet in kernel-doc-nano-HOWTO.txt is
also fixed.
Signed-off-by: Kevin Diggs <kevdig@hypersurf.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Added the basic support of AD1882A codec chip.
It's almost compatible with AD1882, but with a digital mic and some
differences in connections.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
By calling pcmcia_loop_config(), a pcmcia driver can iterate over all
available configuration options. During a driver's probe() phase, one
doesn't need to use pcmcia_get_{first,next}_tuple, pcmcia_get_tuple_data
and pcmcia_parse_tuple directly in most if not all cases.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Update documentation to remind users to update mke2fs.conf
ext4: Fix small file fragmentation
ext4: Initialize writeback_index to 0 when allocating a new inode
ext4: make sure ext4_has_free_blocks returns 0 for ENOSPC
ext4: journal credit fix for the delayed allocation's writepages() function
ext4: Rework the ext4_da_writepages() function
ext4: journal credits reservation fixes for DIO, fallocate
ext4: journal credits reservation fixes for extent file writepage
ext4: journal credits calulation cleanup and fix for non-extent writepage
ext4: Fix bug where we return ENOSPC even though we have plenty of inodes
ext4: don't try to resize if there are no reserved gdt blocks left
ext4: Use ext4_discard_reservations instead of mballoc-specific call
ext4: Fix ext4_dx_readdir hash collision handling
ext4: Fix delalloc release block reservation for truncate
ext4: Fix potential truncate BUG due to i_prealloc_list being non-empty
ext4: Handle unwritten extent properly with delayed allocation
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] pata_it821x: fix warning
libata: Fix a large collection of DMA mode mismatches
ahci: sis controllers actually can do PMP
pata_via: clean up recent tf_load changes
libata: restore SControl on detach
libata: use ata_link_printk() when printing SError
libata: always do follow-up SRST if hardreset returned -EAGAIN
libata: fix EH action overwriting in ata_eh_reset()
sata_mv: add the Gen IIE flag to the SoC devices.
ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
sata_mv: don't issue two DMA commands concurrently
libata: implement no[hs]rst force params
Implement force params nohrst, nosrst and norst. This is to work
around reset related problems and ease debugging.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hi,
This patch adds SubmitChecklist translated into Japanese to
Documentation/ja_JP directory.
The translated SubmitChecklist has already been reviewed by JF project.
SubmitChecklist is one of the important policy documents.
So, I would like to merge into 2.6.27.
Signed-off-by: Takenori Nagano <t-nagano@ah.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation update for PAT. Reflect the latest API details.
Also, adds details about ways to get more info in order to debug PAT.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rewrite of the CFS documentation - because the old one was sorely
out-dated.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"bootmem_debug" is not mentioned in kernel-parameters.txt. Recently I
had to use that kernel option and I think it should be documented.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (22 commits)
[SCSI] ibmvfc: Driver version 1.0.2
[SCSI] ibmvfc: Add details to async event log
[SCSI] ibmvfc: Sanitize response lengths
[SCSI] ibmvfc: Fix for lost async events
[SCSI] ibmvfc: Fixup host state during reinit
[SCSI] ibmvfc: Fix another hang on module removal
[SCSI] ibmvscsi: Fixup desired DMA value for shared memory partitions
[SCSI] megaraid_sas: remove sysfs dbg_lvl world writeable permissions
[SCSI] qla2xxx: Update version number to 8.02.01-k7.
[SCSI] qla2xxx: Explicitly tear-down vports during PCI remove_one().
[SCSI] qla2xxx: Reference proper ha during SBR handling.
[SCSI] qla2xxx: Set npiv_supported flag for FCoE HBAs.
[SCSI] qla2xxx: Don't leak SG-DMA mappings while aborting commands.
[SCSI] qla2xxx: Correct vport-state management issues during ISP-ABORT.
[SCSI] qla2xxx: Correct synchronization of software/firmware fcport states.
[SCSI] scsi_dh: Initialize lun_state in check_ownership()
[SCSI] scsi_dh: Do not use scsilun in rdac hardware handler
[SCSI] megaraid_sas: version and Documentation Update
[SCSI] megaraid_sas: add new controllers (0x78 0x79)
[SCSI] megaraid_sas: add the shutdown DCMD cmd to driver shutdown routine
...
Add security/inode.c functions to the kernel-api docbook.
Use '%' on constants in kernel-doc notation.
Fix several typos/spellos in security function descriptions.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Morris <jmorris@namei.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (94 commits)
pkt_sched: Prevent livelock in TX queue running.
Revert "pkt_sched: Add BH protection for qdisc_stab_lock."
Revert "pkt_sched: Protect gen estimators under est_lock."
pkt_sched: remove bogus block (cleanup)
nf_nat: use secure_ipv4_port_ephemeral() for NAT port randomization
netfilter: ctnetlink: sleepable allocation with spin lock bh
netfilter: ctnetlink: fix sleep in read-side lock section
netfilter: ctnetlink: fix double helper assignation for NAT'ed conntracks
netfilter: ipt_addrtype: Fix matching of inverted destination address type
dccp: Fix panic caused by too early termination of retransmission mechanism
pkt_sched: Don't hold qdisc lock over qdisc_destroy().
pkt_sched: Add lockdep annotation for qdisc locks
pkt_sched: Never schedule non-root qdiscs.
removed unused #include <version.h>
rt2x00: Fix txdone_entry_desc_flags
b43: Fix for another Bluetooth Coexistence SPROM Programming error for BCM4306
mac80211: remove kdoc references to IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE
p54u: reset skb's data/tail pointer on requeue
p54: move p54_vdcf_init to the right place.
iwlwifi: fix printk newlines
...
Guard rfkill controllers attached to a rfkill class against state changes
after class suspend has been issued.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch improves the performance of the ecc generation code by a
factor of 18 on an INTEL D920 CPU, a factor of 7 on MIPS and a factor of 5
on ARM (NSLU2)
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'linux-next' of git://git.infradead.org/~dedekind/ubifs-2.6: (29 commits)
UBIFS: xattr bugfixes
UBIFS: remove unneeded check
UBIFS: few commentary fixes
UBIFS: fix budgeting request alignment in xattr code
UBIFS: improve arguments checking in debugging messages
UBIFS: always set i_generation to 0
UBIFS: correct spelling of "thrice".
UBIFS: support splice_write
UBIFS: minor tweaks in commit
UBIFS: reserve more space for index
UBIFS: print pid in dump function
UBIFS: align inode data to eight
UBIFS: improve budgeting checks
UBIFS: correct orphan deletion order
UBIFS: fix typos in comments
UBIFS: do not union creat_sqnum and del_cmtno
UBIFS: optimize deletions
UBIFS: increment commit number earlier
UBIFS: remove another unneeded function parameter
UBIFS: remove unneeded function parameter
...
Minor documentation update to reflect the current full name of the power
management hardware interface and reflows the text a bit.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With man-pages-3.07, the numa_maps documentation home is now proc(5), so
the reference in Documentation/vm/page_migration needs updating.
(Cliff/Lee are removing numa_maps.5 from the numactl package.) Also, the
download location for the numactl package changed a while back. This
patch fixes both things, as well as a typo (provided-->provides).
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Cliff Wickman <cpw@sgi.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All of the in-tree uses of list_for_each_rcu() have been converted to
list_for_each_entry_rcu(), so list_for_each_rcu() can now be removed.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Added the ignore_ctl_error parameter to enable/disable the control-error
handling for mixer interfaces. It was a hard-coded ifdef, and now you
can change it more easily.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing description of module parameters of usb-audio driver
to ALSA-Configuration.txt.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add support for the Asus Xonar D1. It is the same as the DX, but
without the external power detection.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
this mentions a new deadlock due to advanced power management.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the auerswald USB driver from the linux kernel
2.6.26.
This driver was included into the kernel mainly to connect to the ISDN
framework. This was done in linux 2.4.x. For 2.6.x, due to the fragile
and moving ISDN support, this connection was never realized, and the
only use of this driver was for device configuration. In the age of DSL,
the demand of ISDN support is getting very low.
Meanwhile, with the advent of libusb, an userspace driver was done for
the device configuration which works fine for linux and mac. (Thanks to
the libusb developers!). The userspace driver is downloadable from the
auerswald web site.
So this driver is obsolete now and has to be removed. Many thanks to all
developers which helped me to bring this driver up and working.
Signed-off-by: Wolfgang Muees <wolfgang@iksw-muees.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds