Here is the big set of USB patches for 5.4-rc1.
Two major chunks of code are moving out of the tree and into the staging
directory, uwb and wusb (wireless USB support), because there are no
devices that actually use this protocol anymore, and what we have today
probably doesn't work at all given that the maintainers left many many
years ago. So move it to staging where it will be removed in a few
releases if no one screams.
Other than that, lots of little things. The usual gadget and xhci and
usb serial driver updates, along with a bunch of sysfs file cleanups due
to the driver core changes to support that. Nothing really major, just
constant forward progress.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIYYQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymn8ACfTi8Y2ku/yqw8Nvs4vQjc08MUDhgAoNnbhsI6
H3HUrZTjJJzuxHCM22Lh
=8ZRm
-----END PGP SIGNATURE-----
Merge tag 'usb-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.4-rc1.
Two major chunks of code are moving out of the tree and into the
staging directory, uwb and wusb (wireless USB support), because there
are no devices that actually use this protocol anymore, and what we
have today probably doesn't work at all given that the maintainers
left many many years ago. So move it to staging where it will be
removed in a few releases if no one screams.
Other than that, lots of little things. The usual gadget and xhci and
usb serial driver updates, along with a bunch of sysfs file cleanups
due to the driver core changes to support that. Nothing really major,
just constant forward progress.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: usbcore: Fix slab-out-of-bounds bug during device reset
usb: cdns3: Remove redundant dev_err call in cdns3_probe()
USB: rio500: Fix lockdep violation
USB: rio500: simplify locking
usb: mtu3: register a USB Role Switch for dual role mode
usb: common: add USB GPIO based connection detection driver
usb: common: create Kconfig file
usb: roles: get usb-role-switch from parent
usb: roles: Add fwnode_usb_role_switch_get() function
device connection: Add fwnode_connection_find_match()
usb: roles: Introduce stubs for the exiting functions in role.h
dt-bindings: usb: mtu3: add properties about USB Role Switch
dt-bindings: usb: add binding for USB GPIO based connection detection driver
dt-bindings: connector: add optional properties for Type-B
dt-binding: usb: add usb-role-switch property
usbip: Implement SG support to vhci-hcd and stub driver
usb: roles: intel: Enable static DRD mode for role switch
xhci-ext-caps.c: Add property to disable Intel SW switch
usb: dwc3: remove generic PHY calibrate() calls
usb: core: phy: add support for PHY calibration
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
With only 45 non-merge commits, we have a small merge window from the
Gadget perspective.
The biggest change here is the addition of the Cadence USB3 DRD
Driver. All other changes are small, non-critical fixes or smaller new
features like the improvement to BESL handling in dwc3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=KUJN
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: Changes for v5.4 merge window
With only 45 non-merge commits, we have a small merge window from the
Gadget perspective.
The biggest change here is the addition of the Cadence USB3 DRD
Driver. All other changes are small, non-critical fixes or smaller new
features like the improvement to BESL handling in dwc3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* tag 'usb-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (45 commits)
usb: gadget: net2280: Add workaround for AB chip Errata 11
usb: gadget: net2280: Move all "ll" registers in one structure
usb: dwc3: gadget: Workaround Mirosoft's BESL check
usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
usb: cdns3: Add Cadence USB3 DRD Driver
usb: common: Simplify usb_decode_get_set_descriptor function.
usb: common: Patch simplify usb_decode_set_clear_feature function.
usb: common: Separated decoding functions from dwc3 driver.
dt-bindings: add binding for USBSS-DRD controller.
usb: gadget: composite: Set recommended BESL values
usb: dwc3: gadget: Set BESL config parameter
usb: dwc3: Separate field holding multiple properties
usb: gadget: Export recommended BESL values
usb: phy: phy-fsl-usb: Make structure fsl_otg_initdata constant
usb: udc: lpc32xx: silence fall-through warning
usb: dwc3: meson-g12a: fix suspend resume regulator unbalanced disables
usb: udc: lpc32xx: remove set but not used 3 variables
usb: gadget: udc: core: Fix segfault if udc_bind_to_driver() for pending driver fails
usb: dwc3: st: Add of_dev_put() in probe function
usb: dwc3: st: Add of_node_put() before return in probe function
...
The errata description is:
Workaround for Default Duration of LFPS Handshake Signaling for
Device-Initiated U1 Exit is too short.
The default duration of the LFPS handshake generated by USB3380 for a device-initiated U1-exit may not be
long enough for certain SuperSpeed downstream ports (SuperSpeed hubs/hosts) to recognize. This could lead
to USB3380 entering the recovery state pre-maturely and ending up in the SS.Inactive state.
I have observed various enumeration failures, seemingly related to
lost transactions or SETUP status phases on modern hosts (typically
thunderbolt capable systems) without this workaround.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The split into multiple structures of the "ll" register bank is
impractical. It makes it hard to add ll_lfps_timers_2 which is
at offset 0x794, which is outside of the existing "lfps" structure
and would require us to add yet another one.
Instead, move all the "ll" registers into a single usb338x_ll_regs
structure, and add ll_lfps_timers_2 while at it. It will be used
in a subsequent patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Silence the following fall-through warning by adding a break statement:
drivers/usb/gadget/udc/lpc32xx_udc.c:2230:3: warning: this statement may
fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_protocol_cmd_r’:
drivers/usb/gadget/udc/lpc32xx_udc.c:744:6: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable]
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_handle_dma_ep’:
drivers/usb/gadget/udc/lpc32xx_udc.c:1994:14: warning: variable ‘epstatus’ set but not used [-Wunused-but-set-variable]
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_handle_ep0_setup’:
drivers/usb/gadget/udc/lpc32xx_udc.c:2200:22: warning: variable ‘wLength’ set but not used [-Wunused-but-set-variable]
It is not used since commit 90fccb529d ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Silence the following fall-through warning by adding a break statement:
drivers/usb/gadget/udc/lpc32xx_udc.c:2230:3: warning: this statement may
fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190821021627.GA2679@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only thing that prevents building this driver on other
platforms is the mach/hardware.h include, which is not actually
used here at all, so remove the line and allow CONFIG_COMPILE_TEST.
Link: https://lore.kernel.org/r/20190809144043.476786-3-arnd@arndb.de
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since the role_store() uses strncmp(), it's possible to refer
out-of-memory if the sysfs data size is smaller than strlen("host").
This patch fixes it by using sysfs_streq() instead of strncmp().
Fixes: cc995c9ec1 ("usb: gadget: udc: renesas_usb3: add support for usb role swap")
Cc: <stable@vger.kernel.org> # v4.12+
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We just accept them instead of stalling and return
zeros on GetTTState.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When nuking requests, it's useful to display how many were
actually nuked. It has proven handy when debugging issues
where EP0 went in a wrong state.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The state bit in the hub is sufficient
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We had some dodgy code using the speed setting to decide whether a
port reset would reset the device or just enable it.
Instead, if the device is disabled and has a gadget attached, a
reset will enable it. If it's already enabled, a reset will
reset it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A disconnect may just suspend the hub in absence of a physical
disconnect detection. If we start rejecting requests, the mass
storage function gets into a spin trying to requeue the same
request for ever and hangs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When stalling EP0, we need to wait for an ACK interrupt,
otherwise we may get out of sync on the next setup packet
data phase. Also we need to ignore the direction when
processing that interrupt as the HW reports a potential
mismatch.
Implement this by adding a stall state to EP0. This fixes
some reported issues with mass storage and some hosts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Otherwise, we can have a stale state after a disconnect and reconnect
causing errors on the first SETUP packet to the device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This bit should be only set when the port enable goes down, for
example, on errors. Not when it gets set after a port reset. Some
USB stacks seem to be sensitive to this and fails enumeration.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: tct_hammer_defconfig arm):
drivers/usb/gadget/udc/s3c2410_udc.c:314:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/usb/gadget/udc/s3c2410_udc.c:418:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190805191426.GA12414@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: at91_dt_defconfig arm):
drivers/usb/gadget/udc/atmel_usba_udc.c:329:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190805184842.GA8627@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: at91_dt_defconfig arm):
drivers/usb/gadget/udc/atmel_usba_udc.c:329:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: tct_hammer_defconfig arm):
drivers/usb/gadget/udc/s3c2410_udc.c:314:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/usb/gadget/udc/s3c2410_udc.c:418:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-47-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable ret is being initialized with a value that is never read and
ret is being re-assigned immediately after the initialization in both
paths of an if statement. This is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The pointer 's' is being assigned however the pointer is
never used with either of these values before it it reassigned much
later on. I suspect it was going to be used in the output of the
main control registers scnprintf but was omitted. The assignments
of 's' to the driver name or the literal string are redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With the current implementation omap_udc_stop is always
returning -ENODEV.
Added changes to return 0 and remove variable status.
Issue identified with coccicheck
drivers/usb/gadget/udc/omap_udc.c:2106:6-12:
Unneeded variable: "status". Return "- ENODEV" on line 2128
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes below warning reported by coccicheck
drivers/usb/gadget/udc/fotg210-udc.c:484:5-8: Unneeded variable: "ret".
Return "0" on line 507
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
at91_wakeup is always returning -EINVAL.
But usb_gadget_wakeup expects 0 on success and negative number on
failure. As per current implementation this function wont fail.
This patch removes unneeded variable and returns 0.
Issue identified by coccicheck
drivers/usb/gadget/udc/at91_udc.c:802:6-12:
Unneeded variable: "status". Return "- EINVAL" on line 821
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The RZ/G2E cat874 board has a type-c connector connected to hd3ss3220 usb
type-c drp port controller. Enhance role switch support to assign the role
requested by connector device using the usb role switch class framework.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
This issue was detected by using the Coccinelle software.
Fixes: 408b56ca5c ("usb: gadget: udc: lpc32xx: simplify probe")
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget drivers may queue request in interrupt context. This would lead to
a descriptor allocation in that context. In that case we would hit
BUG_ON(in_interrupt()) in __get_vm_area_node.
Also remove the unnecessary cast.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: James Grant <jamesg@zaltys.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no deallocation of fusb300->ep[i] elements, allocated at
fusb300_probe.
The patch adds deallocation of fusb300->ep array elements.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the USB device is connected to a host, the CPU cannot be suspended or
else the USB device appears to be disconnected from the host's point of
view. Only after a "USB suspend" state has been entered (as set by the
host) or the host is disconnected can the system safely be suspended: in
both these states, the clock is stopped. As such, this patch associates
a "wake lock" with the running clock of the UDC to keep the system awake
as long as the host maintains the USB connection active.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
CC: Cristian Birsan <cristian.birsan@microchip.com>
CC: Felipe Balbi <balbi@kernel.org>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Nicolas Ferre <nicolas.ferre@microchip.com>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Ludovic Desroches <ludovic.desroches@microchip.com>
CC: linux-arm-kernel@lists.infradead.org
CC: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for USB suspend to the Atmel UDC.
When suspended, the UDC clock can be stopped, resulting in some power
savings. The "wake up" interrupt will fire irregardless of whether the
clock is running or not, allowing the UDC clock to be restarted when the
USB master wants to wake the device again.
The IRQ state of this device is somewhat fiddly. The "wake up" IRQ
seems to actually be a "bus activity" indicator; the IRQ is almost
continuously asserted so enabling this IRQ should only be done after a
suspend when the wake IRQ becomes relevant. Similarly, the "suspend"
IRQ detects "bus inactivity" and may therefore fire together with a
"wake" if the two types of activity coincide during the period between
two IRQ handler invocations; therefore, it's important to ignore the
"suspend" IRQ while waiting for a wake-up.
This has been tested on a SAMA5D2 board.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
CC: Cristian Birsan <cristian.birsan@microchip.com>
CC: Felipe Balbi <balbi@kernel.org>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Nicolas Ferre <nicolas.ferre@microchip.com>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Ludovic Desroches <ludovic.desroches@microchip.com>
CC: linux-arm-kernel@lists.infradead.org
CC: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds set and clear functions for enabling/disabling
interrupts. This simplifies the implementation a bit as the masking of
previously set bits doesn't need to be so explicit.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
CC: Cristian Birsan <cristian.birsan@microchip.com>
CC: Felipe Balbi <balbi@kernel.org>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Nicolas Ferre <nicolas.ferre@microchip.com>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Ludovic Desroches <ludovic.desroches@microchip.com>
CC: linux-arm-kernel@lists.infradead.org
CC: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In some places, the code prints a human-readable USB endpoint
transfer type (e.g. "bulk"). This involves a switch statement
sometimes wrapped around in ({ ... }) block leading to code
repetition.
To make this scenario easier, here introduces usb_ep_type_string()
function, which returns a human-readable name of provided
endpoint type.
It also changes a few places switch was used to use this
new function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no actual need to do the enable/disable_irq dance. Instead enable
the interrupts on the phy only when necessary.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The STOTG04 phy is used as a drop-in replacement of the ISP1301 but some
bits doesn't have exactly the same meaning and this can lead to issues.
Detect the phy dynamically and avoid writing to reserved bits.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Only INT_VBUS_VLD is set to generate ATX interrupts on the phy but
INT_SESS_VLD is checked in vbus_work. This leads to cases where
hot-plugging USB doesn't work after boot.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use a threaded IRQ to handle vbus_work instead of using the global
worqueue.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Simplify .probe and .remove by using devm managed allocations and requests.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The net2280 UDC driver (and also net2272, probably via copy-and-paste)
incorrectly checks the req->zero flag during OUT transfers, after
copying data from the UDC's FIFO into memory. This makes no sense at
all; the "zero" flag indicates that an extra zero-length packet should
be appended to an IN transfer if the length is an even multiple of the
maxpacket size. It has nothing to do with OUT transfers.
In practice this doesn't cause any problems because gadget drivers
never set req->zero for OUT transfers anyway. Still, it is an error
and unnecessary code, so this patch removes the check.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The net2280 driver includes an unnecessary test for an endpoint's
queue being empty. The test is redundant; it sits inside a
conditional block of an "if" statement which already tests the
endpoint's queue.
This patch removes the redundant test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The syzkaller USB fuzzer identified a failure mode in which dummy-hcd
would never give back an unlinked URB. This causes usb_kill_urb() to
hang, leading to WARNINGs and unkillable threads.
In dummy-hcd, all URBs are given back by the dummy_timer() routine as
it scans through the list of pending URBS. Failure to give back URBs
can be caused by failure to start or early exit from the scanning
loop. The code currently has two such pathways: One is triggered when
an unsupported bus transfer speed is encountered, and the other by
exhausting the simulated bandwidth for USB transfers during a frame.
This patch removes those two paths, thereby allowing all unlinked URBs
to be given back in a timely manner. It adds a check for the bus
speed when the gadget first starts running, so that dummy_timer() will
never thereafter encounter an unsupported speed. And it prevents the
loop from exiting as soon as the total bandwidth has been used up (the
scanning loop continues, giving back unlinked URBs as they are found,
but not transferring any more data).
Thanks to Andrey Konovalov for manually running the syzkaller fuzzer
to help track down the source of the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+d919b0f29d7b5a4994b9@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Restore the status of ep->stopped in function net2272_dequeue().
When the given request is not found in the endpoint queue
the function returns -EINVAL without restoring the state of
ep->stopped. Thus the endpoint keeps blocked and does not transfer
any data anymore.
This fix is only compile-tested, since we do not have a
corresponding hardware. An analogous fix was tested in the sibling
driver. See "usb: gadget: net2280: Fix net2280_dequeue()"
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When a request must be dequeued with net2280_dequeue() e.g. due
to a device clear action and the same request is finished by the
function scan_dma_completions() then the function net2280_dequeue()
does not find the request in the following search loop and
returns the error -EINVAL without restoring the status ep->stopped.
Thus the endpoint keeps blocked and does not receive any data
anymore.
This fix restores the status and does not issue an error message.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Linus Torvalds