This fixes setting the clock divider on the TI OMAP-L138 LCDK board.
The clock drivers for OMAP-L138 are being covernted to the common clock
framework. When this happens, clk_set_rate() will no longer return an
error. However, on this SoC, the clock rate cannot actually be changed
because the clock has to maintain a fixed ratio to the ARM clock. So
after attempting to set the clock rate, we need to check to see if the
new rate is actually close enough. If not, then follow the previous
error path to adjust the divider in LCDC IP block to compensate for not
being able to change the parent clock rate.
Tested working on a TI OMAP-L138 LCDK board.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Rename the bundled tilcdc_panel driver from just "panel" to
"tilcdc-panel" to avoid noisy error messages from the driver trying to
probe all device nodes named "panel".
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for drm panels to tilcdc. Adding the support on top of the
existing bridge support needs only couple of lines of code when using
using the drm panel bridge helpers.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Omit an extra message for a memory allocation failure in these functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PnqB
-----END PGP SIGNATURE-----
Merge tag 'tilcdc-4.16' of https://github.com/jsarha/linux into drm-next
drm/tilcdc changes for 4.16
* tag 'tilcdc-4.16' of https://github.com/jsarha/linux:
drm/tilcdc: make tilcdc_mode_hvtotal() static
drm/tilcdc: Remove drm_framebuffer_get() and *_put() calls
drm/tilcdc: ensure nonatomic iowrite64 is not used
The function tilcdc_mode_hvtotal is local to the source and does not need
to be in global scope, so make it static.
drivers/gpu/drm/tilcdc/tilcdc_crtc.c:297:6: warning: no previous prototype for 'tilcdc_mode_hvtotal' [-Wmissing-prototypes]
uint tilcdc_mode_hvtotal(const struct drm_display_mode *mode)
Signed-off-by: Xiongwei Song <sxwjean@gmail.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
The drm_framebuffer_get() and drm_framebuffer_put() calls in the
tilcdc driver are obsolete. The drm atomic modesetting core should
take care of holding the references while the atomic state object is
in use. The old state is deleted when a commit of a new one is
completed after drm_atomic_helper_wait_for_vblanks().
This also fixes an occasional framebuffer leak the old
drm_framebuffer_get() and drm_framebuffer_put() code had.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Add a check to ensure iowrite64 is only used if it is atomic.
It was decided in [1] that the tilcdc driver should not be using an
atomic operation (so it was left out of this patchset). However, it turns
out that through the drm code, a nonatomic header is actually included:
include/linux/io-64-nonatomic-lo-hi.h
is included from include/drm/drm_os_linux.h:9:0,
from include/drm/drmP.h:74,
from include/drm/drm_modeset_helper.h:26,
from include/drm/drm_atomic_helper.h:33,
from drivers/gpu/drm/tilcdc/tilcdc_crtc.c:19:
And thus, without this change, this patchset would inadvertantly
change the behaviour of the tilcdc driver.
[1] lkml.kernel.org/r/CAK8P3a2HhO_zCnsTzq7hmWSz5La5Thu19FWZpun16iMnyyNreQ@mail.gmail.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Use drm_fb_cma_fbdev_init() and drm_fb_cma_fbdev_fini() which relies on
the fact that drm_device holds a pointer to the drm_fb_helper structure.
This means that the driver doesn't have to keep track of that.
Also use the drm_fb_helper functions directly.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Jyri Sarha <jsarha@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115142001.45358-16-noralf@tronnes.org
Cross-subsystem Changes:
- device tree doc for the Mitsubishi AA070MC01 and Tianma TM070RVHG71
panels (Lukasz Majewski) and for a 2nd endpoint on stm32 (Philippe Cornu)
Core Changes:
The most important changes are:
- Add drm_driver .last_close and .output_poll_changed helpers to reduce
fbdev emulation footprint in drivers (Noralf)
- Fix plane clipping in core and for vmwgfx (Ville)
Then we have a bunch of of improvement for print and debug such as the
addition of a framebuffer debugfs file. ELD connector, HDMI and
improvements. And a bunch of misc improvements, clean ups and style
changes and doc updates
[airlied: drop eld bits from amdgpu_dm]
Driver Changes:
- sii8620: filter unsupported modes and add DVI mode support (Maciej Purski)
- rockchip: analogix_dp: Remove unnecessary init code (Jeffy Chen)
- virtio, cirrus: add fb create_handle support to enable screenshots(Lepton Wu)
- virtio: replace reference/unreference with get/put (Aastha Gupta)
- vc4, gma500: Convert timers to use timer_setup() (Kees Cook)
- vc4: Reject HDMI modes with too high of clocks (Eric)
- vc4: Add support for more pixel formats (Dave Stevenson)
- stm: dsi: Rename driver name to "stm32-display-dsi" (Philippe Cornu)
- stm: ltdc: add a 2nd endpoint (Philippe Cornu)
- via: use monotonic time for VIA_WAIT_IRQ (Arnd Bergmann)
* tag 'drm-misc-next-2017-11-30' of git://anongit.freedesktop.org/drm/drm-misc: (96 commits)
drm/bridge: tc358767: add copyright lines
MAINTAINERS: change maintainer for Rockchip drm drivers
drm/vblank: Fix vblank timestamp debugs
drm/via: use monotonic time for VIA_WAIT_IRQ
dma-buf: Fix ifnullfree.cocci warnings
drm/printer: Add drm_vprintf()
drm/edid: Allow HDMI infoframe without VIC or S3D
video/hdmi: Allow "empty" HDMI infoframes
dma-buf/fence: Fix lock inversion within dma-fence-array
drm/sti: Handle return value of platform_get_irq_byname
drm/vc4: Add support for NV21 and NV61.
drm/vc4: Use .pixel_order instead of custom .flip_cbcr
drm/vc4: Add support for DRM_FORMAT_RGB888 and DRM_FORMAT_BGR888
drm: Move drm_plane_helper_check_state() into drm_atomic_helper.c
drm: Check crtc_state->enable rather than crtc->enabled in drm_plane_helper_check_state()
drm/vmwgfx: Try to fix plane clipping
drm/vmwgfx: Use drm_plane_helper_check_state()
drm/vmwgfx: Remove bogus crtc coords vs fb size check
gpu: gma500: remove unneeded DRIVER_LICENSE #define
drm: don't link DP aux i2c adapter to the hardware device node
...
-----BEGIN PGP SIGNATURE-----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=P4O6
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15-part2' of git://people.freedesktop.org/~airlied/linux
Pull more drm updates from Dave Airlie:
"Fixes/cleanups for rc1, non-desktop flags for VR
- remove the MSM dt-bindings file Rob managed to push in the previous
pull.
- add a property/edid quirk to denote HMD devices, I had these
hanging around for a few weeks and Keith had done some work on
them, they are fairly self contained and small, and only affect
people using HTC Vive VR headsets so far.
- amdgpu, tegra, tilcdc, fsl fixes
- some imx-drm cleanups I missed, these seemed pretty small, and no
reason to hold off.
I have one TTM regression fix (fixes bochs-vga in qemu) sitting
locally awaiting review I'll probably send that in a separate pull
request tomorrow"
* tag 'drm-for-v4.15-part2' of git://people.freedesktop.org/~airlied/linux: (33 commits)
dt-bindings: remove file that was added accidentally
drm/edid: quirk HTC vive headset as non-desktop. [v2]
drm/fb: add support for not enabling fbcon on non-desktop displays [v2]
drm: add connector info/property for non-desktop displays [v2]
drm/amdgpu: fix rmmod KCQ disable failed error
drm/amdgpu: fix kernel hang when starting VNC server
drm/amdgpu: don't skip attributes when powerplay is enabled
drm/amd/pp: fix typecast error in powerplay.
drm/tilcdc: Remove obsolete "ti,tilcdc,slave" dts binding support
drm/tegra: sor: Reimplement pad clock
Revert "drm/radeon: dont switch vt on suspend"
drm/amd/amdgpu: fix over-bound accessing in amdgpu_cs_wait_any_fence
drm/amd/powerplay: fix unfreeze level smc message for smu7
drm/amdgpu:fix memleak
drm/amdgpu:fix memleak in takedown
drm/amd/pp: fix dpm randomly failed on Vega10
drm/amdgpu: set f_mapping on exported DMA-bufs
drm/amdgpu: Properly allocate VM invalidate eng v2
drm/fsl-dcu: enable IRQ before drm_atomic_helper_resume()
drm/fsl-dcu: avoid disabling pixel clock twice on suspend
...
Bake in the conflict between the drm_print.h extraction and the
addition of DRM_DEBUG_LEASES since we lost it a few too many times.
Also fix a new use of drm_plane_helper_check_state in msm to follow
Ville's conversion in
commit a01cb8ba3f
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Nov 1 22:16:19 2017 +0200
drm: Move drm_plane_helper_check_state() into drm_atomic_helper.c
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch removes DRM_TILCDC_SLAVE_COMPAT option for supporting the
obsolete "ti,tilcdc,slave" device tree binding. The new of_graph based
binding - that is widely used in other drm driver too - has been
supported since Linux v4.2. Maintaining the the backwards dts
conversion code in the DRM_TILCDC_SLAVE_COMPAT has become a nuisance
for the device/of development so the we decided to drop it after Linux
v4.14, the 2017 LTS.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----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=xVV2
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
There is a new core debugfs file that prints fb/gem info:
<debugfs>/dri/<n>/framebuffer
Use drm_gem_cma_print_info() to provide info to that output instead
of using drm_fb_cma_debugfs_show().
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171107191348.17555-11-noralf@tronnes.org
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The process of applying an overlay consists of:
- unflatten an overlay FDT (flattened device tree) into an
EDT (expanded device tree)
- fixup the phandle values in the overlay EDT to fit in a
range above the phandle values in the live device tree
- create the overlay changeset to reflect the contents of
the overlay EDT
- apply the overlay changeset, to modify the live device tree,
potentially changing the maximum phandle value in the live
device tree
There is currently no protection against two overlay applies
concurrently determining what range of phandle values are in use
in the live device tree, and subsequently changing that range.
Add a mutex to prevent multiple overlay applies from occurring
simultaneously.
Move of_resolve_phandles() into of_overlay_apply() so that it does not
have to be duplicated by each caller of of_overlay_apply().
The test in of_resolve_phandles() that the overlay tree is detached is
temporarily disabled so that old style overlay unittests do not fail.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
When an attempt to apply an overlay changeset fails, an effort
is made to revert any partial application of the changeset.
When an attempt to remove an overlay changeset fails, an effort
is made to re-apply any partial reversion of the changeset.
The existing code does not check for failure to recover a failed
overlay changeset application or overlay changeset revert.
Add the missing checks and flag the devicetree as corrupt if the
state of the devicetree can not be determined.
Improve and expand the returned errors to more fully reflect the
result of the effort to undo the partial effects of a failed attempt
to apply or remove an overlay changeset.
If the device tree might be corrupt, do not allow further attempts
to apply or remove an overlay changeset.
When creating an overlay changeset from an overlay device tree,
add some additional warnings if the state of the overlay device
tree is not as expected.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch is aimed primarily at drivers/of/overlay.c, but those
changes also have a small impact in a few other files.
overlay.c is difficult to read and maintain. Improve readability:
- Rename functions, types and variables to better reflect what
they do and to be consistent with names in other places,
such as the device tree overlay FDT (flattened device tree),
and make the algorithms more clear
- Use the same names consistently throughout the file
- Update comments for name changes
- Fix incorrect comments
This patch is intended to not introduce any functional change.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ka0T
-----END PGP SIGNATURE-----
Merge tag 'tilcdc-4.15' of https://github.com/jsarha/linux into drm-next
tilcdc changes for v4.15
* tag 'tilcdc-4.15' of https://github.com/jsarha/linux:
drm/tilcdc: Remove redundant OF_DETACHED flag setting
drm/tilcdc: Precalculate total frametime in tilcdc_crtc_set_mode()
drm/tilcdc: Use tilcdc_crtc_shutdown() in tilcdc_crtc_destroy()
drm/tilcdc: Remove WARN_ON(!drm_modeset_is_locked(&crtc->mutex)) checks
drm/tilcdc: Turn raster off in crtc reset, if it was on in the HW
drm/tilcdc: switch to drm_*{get,put} helpers
drm/tilcdc: tilcdc_tfp410: make of_device_ids const.
drm/tilcdc: tilcdc_panel: make of_device_ids const.
of_fdt_unflatten_tree() already sets the flag on this node to
OF_DETACHED, because of_fdt_unflatten_tree() calls
__unflatten_device_tree() with the detached bool set to true.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
We need the total frame refresh time to check if we are too close to
vertical sync when updating the two framebuffer DMA registers and risk
a collision. This new method is more accurate that the previous that
based on mode's vrefresh value, which itself is inaccurate or may not
even be initialized.
Reported-by: Kevin Hao <kexin.hao@windriver.com>
Fixes: 11abbc9f39 ("drm/tilcdc: Set framebuffer DMA address to HW only if CRTC is enabled")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use tilcdc_crtc_shutdown() instead of tilcdc_crtc_disable() in
tilcdc_crtc_destroy() and remove the modeset locking.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
This forces the HW to be in sync with the empty state. This should
help with the problem when LCDC is already enabled (e.g. by the
bootloader) at the initialization phase and the enable fails when a
new mode is applied.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
drm_*_reference() and drm_*_unreference() functions are just
compatibility alias for drm_*_get() and drm_*_put() adn should not be
used by new code. So convert all users of compatibility functions to use
the new APIs.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1496 592 0 2088 828 drivers/gpu/drm/tilcdc/tilcdc_tfp410.o
File size after constify:
text data bss dec hex filename
1880 176 0 2056 808 drivers/gpu/drm/tilcdc/tilcdc_tfp410.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1531 592 0 2123 84b drivers/gpu/drm/tilcdc/tilcdc_panel.o
File size after constify:
text data bss dec hex filename
1915 176 0 2091 82b drivers/gpu/drm/tilcdc/tilcdc_panel.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
For maintaining consistency with kernel coding style replace
reference/unreference in ref counting functions with get/put.
The following cocci script was used to generate the tilcdc patch:
@@
expression ex;
@@
(
-drm_framebuffer_unreference(ex);
+drm_framebuffer_put(ex);
|
-drm_dev_unref(ex);
+drm_dev_put(ex);
|
-drm_framebuffer_reference(ex);
+drm_framebuffer_get(ex);
)
Signed-off-by: Aishwarya Pant <aishpant@gmail.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/3f2f592f6ea28adfea3fd8b70421b2fab38f0b94.1506413698.git.aishpant@gmail.com
It's dead code, the core handles all this directly now.
The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Cc: Chen Feng <puck.chen@hisilicon.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Partially-Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[seanpaul changed subject prefix and fixed conflict in stm/ltdc.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_atomic_helper_swap_state() will be changed to interruptible waiting
in the next few commits, so all drivers have to be changed to handling
failure.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170711143314.2148-10-maarten.lankhorst@linux.intel.com
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The CRTC .disable() helper operation is deprecated for atomic drivers,
the new .atomic_disable() helper operation being preferred. Convert all
atomic drivers to .atomic_disable() to avoid cargo-cult use of
.disable() in new drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-3-laurent.pinchart+renesas@ideasonboard.com
The old state is useful for drivers that need to perform operations at
enable time that depend on the transition between the old and new
states.
While at it, rename the operation to .atomic_enable() to be consistent
with .atomic_disable(), as the .enable() operation is used by atomic
helpers only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-drm and mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> # for hdlcd and mali-dp
Acked-by: Stefan Agner <stefan@agner.ch> # for fsl-dcu
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-2-laurent.pinchart+renesas@ideasonboard.com
Convert drivers to use the new of_graph_get_remote_node() helper
instead of parsing the endpoint node and then getting the remote device
node. Now drivers can just specify the device node and which
port/endpoint and get back the connected remote device node. The details
of the graph binding are nicely abstracted into the core OF graph code.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Jyri Sarha <jsarha@ti.com>
Tested by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Again this is an internal helper, not the official way to lock a crtc.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170322215058.8671-9-daniel.vetter@ffwll.ch
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYzznuAAoJEHm+PkMAQRiGAzMIAJDBo5otTMMLhg8eKj8Cnab4
2NyaoWDN6mtU427rzEKEfZlTtp3gIBVdFex5x442weIdw6BgRQW0dvF/uwEn08yI
9Wx7VJmIUyH9M8VmhDtkUTFrhwUGr29qb3JhENMd7tv/CiJaehGRHCT3xqo5BDdu
xiyPcwSkwP/NH24TS91G87gV6r0I0oKLSAxu+KifEFESrb8gaZaduslzpEj3m/Ds
o9EPpfzaiGAdW5EdNfPtviYbBk7ZOXwtxdMV+zlvsLcaqtYnFEsJZd2WyZL0zGML
VXBVxaYtlyTeA7Mt8YYUL+rDHELSOtCeN5zLfxUvYt+Yc0Y6LFBLDOE5h8b3eCw=
=uKUo
-----END PGP SIGNATURE-----
BackMerge tag 'v4.11-rc3' into drm-next
Linux 4.11-rc3 as requested by Daniel
Less code ftw.
This converts all drivers except the tinydrm helper module. That one
needs more work, since it gets the THIS_MODULE reference from
tinydrm.ko instead of the actual driver module like it should.
Probably needs a similar trick like I used here with generating the
entire struct with a macro.
Cc: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-24-daniel.vetter@ffwll.ch
Touching HW while clocks are off is a serious error and for instance
breaks suspend functionality. After this patch tilcdc_crtc_update_fb()
always updates the primary plane's framebuffer pointer, increases fb's
reference count and stores vblank event. tilcdc_crtc_update_fb() only
writes the fb's DMA address to HW if the crtc is enabled, as
tilcdc_crtc_enable() takes care of writing the address on enable.
This patch also refactors the tilcdc_crtc_update_fb() a bit. Number of
subsequent small changes had made it almost unreadable. There should
be no other functional changes but checking the CRTC's enable
state. However, the locking goes a bit differently and some of the
redundant checks have been removed in this new version.
The enable_lock should be enough to protect the access to
tilcdc_crtc->enabled. The irq_lock protects the access to last_vblank
and next_fb. The check for vrefresh and last_vblank being valid is
redundant, as the vrefresh should be always valid if the CRTC is
enabled and now last_vblank should be too, because it is initialized
to current time when CRTC raster is enabled. If for some reason the
values are not correctly initialized the division by zero warning is
quite appropriate.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix badly hardcoded return return value under fail-label. All goto
branches to the label set the "ret"-variable accordingly.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Merge Laurent's drm_platform removal code. Only conflict is with the
drm_pci.h extraction, which allows me to fix up the misplayed
drm_platform_init fumble that 0day and Stephen Rothwell reported.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The field contains a pointer to the parent platform device of the DRM
device. As struct drm_device also contains a dev pointer to the struct
device embedded in the platform_device structure, the platformdev field
is redundant. Remove it and use the dev pointer directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Vincent Abriou <vincent.abriou@st.com> # For sti
Acked-by: Russell King <rmk+kernel@armlinux.org.uk> # For armada
Acked-by: Rob Clark <robdclark@gmail.com> # For msm
Acked-by: Xinwei Kong<kong.kongxinwei@hisilicon.com>
The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers. For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
While at it, the 'return' of .disable_vblank is dropped to fix the
following checkpatch warning.
WARNING: void function return statements are not generally useful
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Jyri Sarha <jsarha@ti.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-22-git-send-email-shawnguo@kernel.org
David Lechner