The powernow-k6 driver used to read the initial multiplier from the
powernow register. However, there is a problem with this:
* If there was a frequency transition before, the multiplier read from the
register corresponds to the current multiplier.
* If there was no frequency transition since reset, the field in the
register always reads as zero, regardless of the current multiplier that
is set using switches on the mainboard and that the CPU is running at.
The zero value corresponds to multiplier 4.5, so as a consequence, the
powernow-k6 driver always assumes multiplier 4.5.
For example, if we have 550MHz CPU with bus frequency 100MHz and
multiplier 5.5, the powernow-k6 driver thinks that the multiplier is 4.5
and bus frequency is 122MHz. The powernow-k6 driver then sets the
multiplier to 4.5, underclocking the CPU to 450MHz, but reports the
current frequency as 550MHz.
There is no reliable way how to read the initial multiplier. I modified
the driver so that it contains a table of known frequencies (based on
parameters of existing CPUs and some common overclocking schemes) and sets
the multiplier according to the frequency. If the frequency is unknown
(because of unusual overclocking or underclocking), the user must supply
the bus speed and maximum multiplier as module parameters.
This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I found out that a system with k6-3+ processor is unstable during network
server load. The system locks up or the network card stops receiving. The
reason for the instability is the CPU frequency scaling.
During frequency transition the processor is in "EPM Stop Grant" state.
The documentation says that the processor doesn't respond to inquiry
requests in this state. Consequently, coherency of processor caches and
bus master devices is not maintained, causing the system instability.
This patch flushes the cache during frequency transition. It fixes the
instability.
Other minor changes:
* u64 invalue changed to unsigned long because the variable is 32-bit
* move the logic to set the multiplier to a separate function
powernow_k6_set_cpu_multiplier
* preserve lower 5 bits of the powernow port instead of 4 (the voltage
field has 5 bits)
* mask interrupts when reading the multiplier, so that the port is not
open during other activity (running other kernel code with the port open
shouldn't cause any misbehavior, but we should better be safe and keep
the port closed)
This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To make the driver multiplatform-friendly, unconditional initialization
in an initcall is replaced with a platform driver probed only if
respective platform device is registered.
Tested at: Exynos4210 (TRATS) and Exynos4412 (TRATS2)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in freq-table. This also makes cpufreq stats
inconsistent as cpufreq-stats would fail to register because current frequency
of CPU isn't found in freq-table.
Because we don't want this change to affect boot process badly, we go for the
next freq which is >= policy->cur ('cur' must be set by now, otherwise we will
end up setting freq to lowest of the table as 'cur' is initialized to zero).
In case current frequency doesn't match any frequency from freq-table, we throw
warnings to user, so that user can get this fixed in their bootloaders or
freq-tables.
Reported-by: Carlos Hernandez <ceh@ti.com>
Reported-and-tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in frequency table.
On some systems we can't really say what frequency we're running at the moment
and so for these we shouldn't check if we are running at a frequency present in
frequency table. And so we really can't force this for all the cpufreq drivers.
Hence we are created another flag here: CPUFREQ_NEED_INITIAL_FREQ_CHECK that
will be marked by platforms which want to go for this check at boot time.
Initially this is done for all ARM platforms but others may follow if required.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a routine check to see if the platform supplied the OPP table.
Incase there's no OPP table exist, it will try to initialise it.
It's been tested on iMX6SL board where the platform doesn't have
an OPP table.
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The imx6q-cpufreq driver nowadays is not only running on imx6q but also
other i.MX6 series SoCs like imx6dl and imx6sl. Update Kconfig prompt
and help text to make it clear to users.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
on i.MX6Q, cpu freq change need to follow below flows:
1. each setpoint has different VDDARM, VDDSOC/PU voltage, get the setpoint
table from dts;
2. when cpu freq is scaling up, need to increase VDDSOC/PU voltage before
VDDARM, if VDDPU is off, no need to change it;
3. when cpu freq is scaling down, need to decrease VDDARM voltage before
VDDSOC/PU, if VDDPU is off, no need to change it;
normally dts will pass vddsoc/pu freq/volt info to kernel, if not, will
use fixed value for vddsoc/pu voltage setting.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the current code, if we fail during a frequency transition, we
simply send the POSTCHANGE notification with the old frequency. This
isn't enough.
One of the core users of these notifications is the code responsible
for keeping loops_per_jiffy aligned with frequency changes. And mostly
it is written as:
if ((val == CPUFREQ_PRECHANGE && freq->old < freq->new) ||
(val == CPUFREQ_POSTCHANGE && freq->old > freq->new)) {
update-loops-per-jiffy...
}
So, suppose we are changing to a higher frequency and failed during
transition, then following will happen:
- CPUFREQ_PRECHANGE notification with freq-new > freq-old
- CPUFREQ_POSTCHANGE notification with freq-new == freq-old
The first one will update loops_per_jiffy and second one will do
nothing. Even if we send the 2nd notification by exchanging values of
freq-new and old, some users of these notifications might get
unstable.
This can be fixed by simply calling cpufreq_notify_post_transition()
with error code and this routine will take care of sending
notifications in the correct order.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Folded 3 patches into one, rebased unicore2 changes]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This introduces a new routine cpufreq_notify_post_transition() which
can be used to send POSTCHANGE notification for new freq with or
without both {PRE|POST}CHANGE notifications for last freq. This is
useful at multiple places, especially for sending transition failure
notifications.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use common clock framework (CCF) APIs to set the clock rates
instead of direct register manipulation. This now updates the
sysfs entry (cpuinfo_cur_freq) correctly which did not reflect
the correct value until now. While at it clean up the PLL s-div
parameter setting as it is handled by the PLL driver.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When a CPU is hot removed we'll cancel all the delayed work items via
gov_cancel_work(). Sometimes the delayed work function determines that
it should adjust the delay for all other CPUs that the policy is
managing. If this scenario occurs, the canceling CPU will cancel its own
work but queue up the other CPUs works to run.
Commit 3617f2 (cpufreq: Fix timer/workqueue corruption due to double
queueing) has tried to fix this, but reading governor_enabled is not
protected by cpufreq_governor_lock. Even though od_dbs_timer() checks
governor_enabled before gov_queue_work(), this scenario may occur. For
example:
CPU0 CPU1
---- ----
cpu_down()
... <work runs>
__cpufreq_remove_dev() od_dbs_timer()
__cpufreq_governor() policy->governor_enabled
policy->governor_enabled = false;
cpufreq_governor_dbs()
case CPUFREQ_GOV_STOP:
gov_cancel_work(dbs_data, policy);
cpu0 work is canceled
timer is canceled
cpu1 work is canceled
<waits for cpu1>
gov_queue_work(*, *, true);
cpu0 work queued
cpu1 work queued
cpu2 work queued
...
cpu1 work is canceled
cpu2 work is canceled
...
At the end of the GOV_STOP case cpu0 still has a work queued to
run although the code is expecting all of the works to be
canceled. __cpufreq_remove_dev() will then proceed to
re-initialize all the other CPUs works except for the CPU that is
going down. The CPUFREQ_GOV_START case in cpufreq_governor_dbs()
will trample over the queued work and debugobjects will spit out
a warning:
WARNING: at lib/debugobjects.c:260 debug_print_object+0x94/0xbc()
ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x14
Modules linked in:
CPU: 1 PID: 1205 Comm: sh Tainted: G W 3.10.0 #200
[<c01144f0>] (unwind_backtrace+0x0/0xf8) from [<c0111d98>] (show_stack+0x10/0x14)
[<c0111d98>] (show_stack+0x10/0x14) from [<c01272cc>] (warn_slowpath_common+0x4c/0x68)
[<c01272cc>] (warn_slowpath_common+0x4c/0x68) from [<c012737c>] (warn_slowpath_fmt+0x30/0x40)
[<c012737c>] (warn_slowpath_fmt+0x30/0x40) from [<c034c640>] (debug_print_object+0x94/0xbc)
[<c034c640>] (debug_print_object+0x94/0xbc) from [<c034c7f8>] (__debug_object_init+0xc8/0x3c0)
[<c034c7f8>] (__debug_object_init+0xc8/0x3c0) from [<c01360e0>] (init_timer_key+0x20/0x104)
[<c01360e0>] (init_timer_key+0x20/0x104) from [<c04872ac>] (cpufreq_governor_dbs+0x1dc/0x68c)
[<c04872ac>] (cpufreq_governor_dbs+0x1dc/0x68c) from [<c04833a8>] (__cpufreq_governor+0x80/0x1b0)
[<c04833a8>] (__cpufreq_governor+0x80/0x1b0) from [<c0483704>] (__cpufreq_remove_dev.isra.12+0x22c/0x380)
[<c0483704>] (__cpufreq_remove_dev.isra.12+0x22c/0x380) from [<c0692f38>] (cpufreq_cpu_callback+0x48/0x5c)
[<c0692f38>] (cpufreq_cpu_callback+0x48/0x5c) from [<c014fb40>] (notifier_call_chain+0x44/0x84)
[<c014fb40>] (notifier_call_chain+0x44/0x84) from [<c012ae44>] (__cpu_notify+0x2c/0x48)
[<c012ae44>] (__cpu_notify+0x2c/0x48) from [<c068dd40>] (_cpu_down+0x80/0x258)
[<c068dd40>] (_cpu_down+0x80/0x258) from [<c068df40>] (cpu_down+0x28/0x3c)
[<c068df40>] (cpu_down+0x28/0x3c) from [<c068e4c0>] (store_online+0x30/0x74)
[<c068e4c0>] (store_online+0x30/0x74) from [<c03a7308>] (dev_attr_store+0x18/0x24)
[<c03a7308>] (dev_attr_store+0x18/0x24) from [<c0256fe0>] (sysfs_write_file+0x100/0x180)
[<c0256fe0>] (sysfs_write_file+0x100/0x180) from [<c01fec9c>] (vfs_write+0xbc/0x184)
[<c01fec9c>] (vfs_write+0xbc/0x184) from [<c01ff034>] (SyS_write+0x40/0x68)
[<c01ff034>] (SyS_write+0x40/0x68) from [<c010e200>] (ret_fast_syscall+0x0/0x48)
In gov_queue_work(), lock cpufreq_governor_lock before gov_queue_work,
and unlock it after __gov_queue_work(). In this way, governor_enabled
is guaranteed not changed in gov_queue_work().
Signed-off-by: Jane Li <jiel@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Local variable used only in this file is made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Local variables used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The contents of this header file are not referenced in the driver.
Remove its inclusion.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The arm_big_little cpufreq driver is only used by ARM bigLITTLE
platforms and hence must depend on CONFIG_BIG_LITTLE.
This was highlighted by Russell earlier when he reported this issue:
drivers/built-in.o: In function `bL_cpufreq_set_rate':
powercap_sys.c:(.text+0x5ed9a0): undefined reference to `bL_switch_request_cb'
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prevent __cpufreq_add_dev() from overwriting the existing values of
user_policy.{min|max|policy|governor} with defaults during resume
from system suspend.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If cpufreq_policy_restore() returns NULL during system resume,
__cpufreq_add_dev() should just fall back to the full initialization
instead of returning an error, because that may actually make things
work. Moreover, it should not leave stale fallback data behind after
it has failed to restore a previously existing policy.
This change is based on Viresh Kumar's work.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
- remove <mach/regs-clock.h> for exynos
- remove <mach/regs-irq.h> for exynos
- local <mach/regs-pmu.h> into mach-exynos
- select PM_GENERIC_DOMAINS for ARCH_EXYNOS4
instead of each SOC_EXYNOS4XXX in Kconfig
- call pm_genpd_poweroff_unused() instead of via
exynos_pm_late_initcall() because no need to
handle whether CONFIG_PM_GENERIC_DOMAINS is enalbed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NgIt
-----END PGP SIGNATURE-----
Merge tag 'samsung-cleanup-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
From Kukjin Kim:
Samsung cleanup 2nd for v3.14
- remove <mach/regs-clock.h> for exynos
- remove <mach/regs-irq.h> for exynos
- local <mach/regs-pmu.h> into mach-exynos
- select PM_GENERIC_DOMAINS for ARCH_EXYNOS4
instead of each SOC_EXYNOS4XXX in Kconfig
- call pm_genpd_poweroff_unused() instead of via
exynos_pm_late_initcall() because no need to
handle whether CONFIG_PM_GENERIC_DOMAINS is enalbed
* tag 'samsung-cleanup-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
ARM: EXYNOS: local definitions for cpuidle.c into mach-exynos dir
cpufreq: exynos: move definitions for exynos-cpufreq into drivers/cpufreq/
ARM: EXYNOS: local definitions for pm.c into mach-exynos dir
PM / devfreq: move definitions for exynos4_bus into drivers/devfreq
ARM: EXYNOS: cleanup <mach/regs-clock.h>
ARM: EXYNOS: cleanup <mach/regs-irq.h>
ARM: EXYNOS: local regs-pmu.h header file
ARM: EXYNOS: remove inclusion <mach/regs-pmu.h> into another headers
ARM: EXYNOS: cleanup <mach/regs-pmu.h>
Signed-off-by: Olof Johansson <olof@lixom.net>
PM_OPP is a helper library used by several of the existing cpufreq drivers.
Some of the drivers select this symbol while others depend on it and rely
on the architecture to enable it. Make this behaviour more consistent and
obvious by having all the drivers select the symbol. This will also allow
better build coverage of the affected drivers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The patch currently under review to enable ARM cpufreq drivers for ARM64
which is useful due to the large amount of shared IP between ARM and ARM64
SoCs. However the big.LITTLE switcher relies on an architecture interface
to build which is not present on ARM64. Add a dependency until that is
resolved.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove the periodic P state boost. This code required for some corner
case benchmark tests. The calculation of the required P state was
incorrect/inaccurate and would not allow P state increase.
This was fixed by a combination of commits:
2134ed4 cpufreq / intel_pstate: Change to scale off of max P-state
d253d2a intel_pstate: Improve accuracy by not truncating until final result
References: https://bugzilla.kernel.org/show_bug.cgi?id=64271
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Baytrail requires setting P state and voltage pairs when adjusting the
requested P state. Add function for retrieving the valid voltage
values and modify *_set_pstate() functions to caluclate the
appropriate voltage for the requested P state.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When configuring a default governor (via CONFIG_CPU_FREQ_DEFAULT_*) with the
intel_pstate driver, the desired default policy is not properly set. For
example, setting 'CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE' ends up with the
'powersave' policy being set.
Fix by configuring the correct default policy, if either 'powersave' or
'performance' are requested. Otherwise, fallback to what the driver originally
set via its 'init' routine.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are cases where cpufreq_add_dev() may fail for some CPUs
during system resume. With the current code we will still have
sysfs cpufreq files for those CPUs and struct cpufreq_policy
would be already freed for them. Hence any operation on those
sysfs files would result in kernel warnings.
Example of problems resulting from resume errors (from Bjørn Mork):
WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212()
missing sysfs attribute operations for kobject: (null)
Modules linked in: [stripped as irrelevant]
CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006
ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000
ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310
Call Trace:
[<ffffffff81380b0e>] dump_stack+0x55/0x76
[<ffffffff81038635>] warn_slowpath_common+0x7c/0x96
[<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212
[<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43
[<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82
[<ffffffff81182382>] ? sysfs_open_file+0x32/0x212
[<ffffffff811823c7>] sysfs_open_file+0x77/0x212
[<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac
[<ffffffff81122562>] do_dentry_open+0x17c/0x257
[<ffffffff8112267e>] finish_open+0x41/0x4f
[<ffffffff81130225>] do_last+0x80c/0x9ba
[<ffffffff8112dbbd>] ? inode_permission+0x40/0x42
[<ffffffff81130606>] path_openat+0x233/0x4a1
[<ffffffff81130b7e>] do_filp_open+0x35/0x85
[<ffffffff8113b787>] ? __alloc_fd+0x172/0x184
[<ffffffff811232ea>] do_sys_open+0x6b/0xfa
[<ffffffff811233a7>] SyS_openat+0xf/0x11
[<ffffffff8138c812>] system_call_fastpath+0x16/0x1b
To fix this, remove those sysfs files or put the associated kobject
in case of such errors. Also, to make it simple, remove the cpufreq
sysfs links from all the CPUs (except for the policy->cpu) during
suspend, as that operation won't result in a loss of sysfs file
permissions and we can create those links during resume just fine.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-and-tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This moves regarding exynos-cpufreq definitions into drivers/cpufreq/
exynos-cpufreq.h because they are used only for the cpufreq driver.
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The function at32_cpufreq_driver_init was marked as __init but will be
called from inside the cpufreq framework. This lead to the following a
section mismatch during compilation:
WARNING: drivers/built-in.o(.data+0x2448): Section mismatch in reference
from the variable at32_driver to the function
.init.text:at32_cpufreq_driver_init()
The variable at32_driver references
the function __init at32_cpufreq_driver_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Commit 2167e2399d (cpufreq: fix garbage kobjects on errors during
suspend/resume) breaks suspend/resume on Martin Ziegler's system
(hard lockup during resume), so revert it.
Fixes: 2167e2399d (cpufreq: fix garbage kobjects on errors during suspend/resume)
References: https://bugzilla.kernel.org/show_bug.cgi?id=66751
Reported-by: Martin Ziegler <ziegler@uni-freiburg.de>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 5a87182aa2 (cpufreq: suspend governors on system
suspend/hibernate) causes hibernation problems to happen on
Bjørn Mork's and Paul Bolle's systems, so revert it.
Fixes: 5a87182aa2 (cpufreq: suspend governors on system suspend/hibernate)
Reported-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Treat both negative and zero return values from clk_round_rate()
as errors. This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather
than a signed type, since some clock sources can generate rates
higher than (2^31)-1 Hz.
Eventually, when calling clk_round_rate(), only a return value of
zero will be considered a error. All other values will be
considered valid rates. The comparison against values less than
0 is kept to preserve the correct behavior in the meantime.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Treat both negative and zero return values from clk_round_rate()
as errors. This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather
than a signed type, since some clock sources can generate rates
higher than (2^31)-1 Hz.
Eventually, when calling clk_round_rate(), only a return value of
zero will be considered a error. All other values will be
considered valid rates. The comparison against values less than
0 is kept to preserve the correct behavior in the meantime.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpuidle:
cpuidle: Check for dev before deregistering it.
intel_idle: Fixed C6 state on Avoton/Rangeley processors
* pm-cpufreq:
cpufreq: fix garbage kobjects on errors during suspend/resume
cpufreq: suspend governors on system suspend/hibernate
This patch changes the cpufreq-cpu0 driver to consider if
a cpu needs cooling (with cpufreq). In case the cooling is needed,
the cpu0 device tree node needs to be properly configured
with cooling device properties.
In case these properties are present,, the driver will
load a cpufreq cooling device in the system. The cpufreq-cpu0
driver is not interested in determining how the system should
be using the cooling device. The driver is responsible
only of loading the cooling device.
Describing how the cooling device will be used can be
accomplished by setting up a thermal zone that references
and is composed by the cpufreq cooling device.
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: cpufreq@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This is effectively a revert of commit 5302c3fb2e ("cpufreq: Perform
light-weight init/teardown during suspend/resume"), which enabled
suspend/resume optimizations leaving the sysfs files in place.
Errors during suspend/resume are not handled properly, leaving
dead sysfs attributes in case of failures. There are are number of
functions with special code for the "frozen" case, and all these
need to also have special error handling.
The problem is easy to demonstrate by making cpufreq_driver->init()
or cpufreq_driver->get() fail during resume.
The code is too complex for a simple fix, with split code paths
in multiple blocks within a number of functions. It is therefore
best to revert the patch enabling this code until the error handling
is in place.
Examples of problems resulting from resume errors:
WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212()
missing sysfs attribute operations for kobject: (null)
Modules linked in: [stripped as irrelevant]
CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006
ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000
ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310
Call Trace:
[<ffffffff81380b0e>] dump_stack+0x55/0x76
[<ffffffff81038635>] warn_slowpath_common+0x7c/0x96
[<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212
[<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43
[<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82
[<ffffffff81182382>] ? sysfs_open_file+0x32/0x212
[<ffffffff811823c7>] sysfs_open_file+0x77/0x212
[<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac
[<ffffffff81122562>] do_dentry_open+0x17c/0x257
[<ffffffff8112267e>] finish_open+0x41/0x4f
[<ffffffff81130225>] do_last+0x80c/0x9ba
[<ffffffff8112dbbd>] ? inode_permission+0x40/0x42
[<ffffffff81130606>] path_openat+0x233/0x4a1
[<ffffffff81130b7e>] do_filp_open+0x35/0x85
[<ffffffff8113b787>] ? __alloc_fd+0x172/0x184
[<ffffffff811232ea>] do_sys_open+0x6b/0xfa
[<ffffffff811233a7>] SyS_openat+0xf/0x11
[<ffffffff8138c812>] system_call_fastpath+0x16/0x1b
The failure to restore cpufreq devices on cancelled hibernation is
not a new bug. It is caused by the ACPI _PPC call failing unless the
hibernate is completed. This makes the acpi_cpufreq driver fail its
init.
Previously, the cpufreq device could be restored by offlining the
cpu temporarily. And as a complete hibernation cycle would do this,
it would be automatically restored most of the time. But after
commit 5302c3fb2e the leftover sysfs attributes will block any
device add action. Therefore offlining and onlining CPU 1 will no
longer restore the cpufreq object, and a complete suspend/resume
cycle will replace it with garbage.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds cpufreq suspend/resume calls to dpm_{suspend|resume}_noirq()
for handling suspend/resume of cpufreq governors.
Lan Tianyu (Intel) & Jinhyuk Choi (Broadcom) found anr issue where
tunables configuration for clusters/sockets with non-boot CPUs was
getting lost after suspend/resume, as we were notifying governors
with CPUFREQ_GOV_POLICY_EXIT on removal of the last cpu for that
policy and so deallocating memory for tunables. This is fixed by
this patch as we don't allow any operation on governors after
device suspend and before device resume now.
Reported-and-tested-by: Lan Tianyu <tianyu.lan@intel.com>
Reported-by: Jinhyuk Choi <jinchoi@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog, minor cleanups]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The init functions are linked statically (no support for
dynamic loading) and have no other users. Hence remove
EXPORT_SYMBOL for these functions.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
d4019f0a92 "cpufreq: move freq change notifications to cpufreq core"
added code to the cpufreq core to print an error if a cpufreq driver's
.target() function returned an error. This exposed the fact that Tegra's
cpufreq driver returns an error when it is ignoring requests due to the
system being suspended.
Modify Tegra's .target() function not to return an error in this case;
this prevents the error prints. The argument is that since the suspend
hook can't and doesn't inform the cpufreq core when its requests will
be ignored, there's no way for the cpufreq core to squelch them, so it's
not an error for the requests to keep coming. This change make the Tegra
driver consistent with how the Exynos handles the same situation. Note
that s5pv210-cpufreq.c probably suffers from this same issue though.
Fixes: d4019f0a92 (cpufreq: move freq change notifications to cpufreq core)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
* pm-cpufreq:
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
cpufreq: conservative: set requested_freq to policy max when it is over policy max
The related code has been changed and the comment is out of date.
So remove it.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from
Mika Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar,
Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski,
Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki,
Naresh Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani,
Zhang Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko,
Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JCxk
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
With a recent change "d4019f0 cpufreq: move freq change notifications to cpufreq
core" few variables (r & ret) are removed by mistake and hence these warnings:
drivers/cpufreq/omap-cpufreq.c: In function omap_target:
drivers/cpufreq/omap-cpufreq.c:64:2: error: ret undeclared (first use in this function)
drivers/cpufreq/omap-cpufreq.c:64:2: note: each undeclared identifier is reported only once for each function it appears in
drivers/cpufreq/omap-cpufreq.c:94:3: error: r undeclared (first use in this function)
drivers/cpufreq/omap-cpufreq.c:116:1: warning: control reaches end of non-void function [-Wreturn-type]
Lets fix them by declaring those variables again.
Fixes: d4019f0a92 (cpufreq: move freq change notifications to cpufreq core)
Reported-by: Sebastian Capella <sebastian.capella@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When requested_freq is over policy->max, set it to policy->max.
This can help to speed up decreasing frequency.
Signed-off-by: Xiaoguang Chen <chenxg@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
When decreasing frequency, requested_freq may be less than
freq_target, So requested_freq minus freq_target may be negative,
But reqested_freq's unit is unsigned int, then the negative result
will be one larger interger which may be even higher than
requested_freq.
This patch is to fix such issue. when result becomes negative,
set requested_freq as the min value of policy.
Signed-off-by: Xiaoguang Chen <chenxg@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq:
intel_pstate: skip the driver if ACPI has power mgmt option
cpufreq: ondemand: Remove redundant return statement
cpufreq: move freq change notifications to cpufreq core
cpufreq: distinguish drivers that do asynchronous notifications
cpufreq/intel_pstate: Add static declarations to internal functions
cpufreq: arm_big_little: reconfigure switcher behavior at run time
cpufreq: arm_big_little: add in-kernel switching (IKS) support
ARM: vexpress/TC2: register vexpress-spc cpufreq device
cpufreq: arm_big_little: add vexpress SPC interface driver
ARM: vexpress/TC2: add cpu clock support
ARM: vexpress/TC2: add support for CPU DVFS
Do not load the Intel pstate driver if the platform firmware
(ACPI BIOS) supports the power management alternatives.
The ACPI BIOS indicates that the OS control mode can be used
if the _PSS (Performance Supported States) is defined in ACPI
table. For the OS control mode, the Intel pstate driver will be
loaded.
HP BIOS has several power management modes (firmware, OS-control and
so on). For the OS control mode in HP BIOS, the Intel p-state driver
will be loaded. When the customer chooses the firmware power
management in HP BIOS, the Intel p-state driver will be ignored.
I put hw_vendor_info vendor_info in case other vendors (Dell, Lenovo...)
have their firmware power management. Vendors should make sure their
firmware power management works properly, and they can go for adding
their vendor info to the variable.
I have verified the patch on HP ProLiant servers. The patch worked
correctly.
Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com>
[rjw: Fixed up !CONFIG_ACPI build]
[Linda Knippers: As Adrian has recently left HP, I retested the
updated patch on an HP ProLiant server and verified that it is
behaving correctly. When the BIOS is configured for OS control for
power management, the intel_pstate driver loads as expected. When
the BIOS is configured to provide the power management, the
intel_pstate driver does not load and we get the pcc_cpufreq driver
instead.]
Signed-off-by: Linda Knippers <linda.knippers@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit dfa5bb6225 (cpufreq: ondemand: Change the calculation
of target frequency), this return statement is no longer needed.
Reported-by: Henrik Nilsson <Karl.Henrik.Nilsson@gmail.com>
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the drivers do following in their ->target_index() routines:
struct cpufreq_freqs freqs;
freqs.old = old freq...
freqs.new = new freq...
cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE);
/* Change rate here */
cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE);
This is replicated over all cpufreq drivers today and there doesn't exists a
good enough reason why this shouldn't be moved to cpufreq core instead.
There are few special cases though, like exynos5440, which doesn't do everything
on the call to ->target_index() routine and call some kind of bottom halves for
doing this work, work/tasklet/etc..
They may continue doing notification from their own code as flag:
CPUFREQ_ASYNC_NOTIFICATION is already set for them.
All drivers are also modified in this patch to avoid breaking 'git bisect', as
double notification would happen otherwise.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are few special cases like exynos5440 which doesn't send POSTCHANGE
notification from their ->target() routine and call some kind of bottom halves
for doing this work, work/tasklet/etc.. From which they finally send POSTCHANGE
notification.
Its better if we distinguish them from other cpufreq drivers in some way so that
core can handle them specially. So this patch introduces another flag:
CPUFREQ_ASYNC_NOTIFICATION, which will be set by such drivers.
This also changes exynos5440-cpufreq.c and powernow-k8 in order to set this
flag.
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes warnings reported by kbuild test robot
sparse warnings: (new ones prefixed by >>)
drivers/cpufreq/intel_pstate.c:729:6: sparse: symbol 'copy_pid_params' was not declared. Should it be static?
drivers/cpufreq/intel_pstate.c:739:6: sparse: symbol 'copy_cpu_funcs' was not declared. Should it be static?
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The b.L switcher can be turned on/off at run time. It is therefore
necessary to change the cpufreq driver behavior accordingly.
The driver must be unregistered/registered with the cpufreq core
to reconfigure freq tables for the virtual or actual CPUs. This is
accomplished via the b.L switcher notifier callback.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds IKS (In Kernel Switcher) support to cpufreq driver.
This creates a combined freq table for A7-A15 CPU pairs. A7 frequencies
are virtualized and scaled down to half the actual frequencies to
approximate a linear scale across the combined A7+A15 range. When the
requested frequency change crosses the A7-A15 boundary a cluster switch
is invoked.
Based on earlier work from Sudeep KarkadaNagesha.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The TC2(i.e. CA15_A7) Versatile Express has external Cortex M3 based
power controller which is responsible for CPU DVFS and SPC provides
the interface for the same.
This patch adds a tiny interface driver to check if OPPs are
initialised by SPC platform code and register the arm_big_little
cpufreq driver.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq: (167 commits)
cpufreq: create per policy rwsem instead of per CPU cpu_policy_rwsem
intel_pstate: Add Baytrail support
intel_pstate: Refactor driver to support CPUs with different MSR layouts
cpufreq: Implement light weight ->target_index() routine
PM / OPP: rename header to linux/pm_opp.h
PM / OPP: rename data structures to dev_pm equivalents
PM / OPP: rename functions to dev_pm_opp*
cpufreq / governor: Remove fossil comment
cpufreq: exynos4210: Use the common clock framework to set APLL clock rate
cpufreq: exynos4x12: Use the common clock framework to set APLL clock rate
cpufreq: Detect spurious invocations of update_policy_cpu()
cpufreq: pmac64: enable cpufreq on iMac G5 (iSight) model
cpufreq: pmac64: provide cpufreq transition latency for older G5 models
cpufreq: pmac64: speed up frequency switch
cpufreq: highbank-cpufreq: Enable Midway/ECX-2000
exynos-cpufreq: fix false return check from "regulator_set_voltage"
speedstep-centrino: Remove unnecessary braces
acpi-cpufreq: Add comment under ACPI_ADR_SPACE_SYSTEM_IO case
cpufreq: arm-big-little: use clk_get instead of clk_get_sys
cpufreq: exynos: Show a list of available frequencies
...
Conflicts:
drivers/devfreq/exynos/exynos5_bus.c
We have per-CPU cpu_policy_rwsem for cpufreq core, but we never use
all of them. We always use rwsem of policy->cpu and so we can
actually make this rwsem per policy instead.
This patch does this change. With this change other tricky situations
are also avoided now, like which lock to take while we are changing
policy->cpu, etc.
Suggested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for the Baytrail processor.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Non-core processors have a different MSR layout to commumicate P state
information. Refactor the driver to use CPU dependent accessors to
P state information.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, the prototype of cpufreq_drivers target routines is:
int target(struct cpufreq_policy *policy, unsigned int target_freq,
unsigned int relation);
And most of the drivers call cpufreq_frequency_table_target() to get a valid
index of their frequency table which is closest to the target_freq. And they
don't use target_freq and relation after that.
So, it makes sense to just do this work in cpufreq core before calling
cpufreq_frequency_table_target() and simply pass index instead. But this can be
done only with drivers which expose their frequency table with cpufreq core. For
others we need to stick with the old prototype of target() until those drivers
are converted to expose frequency tables.
This patch implements the new light weight prototype for target_index() routine.
It looks like this:
int target_index(struct cpufreq_policy *policy, unsigned int index);
CPUFreq core will call cpufreq_frequency_table_target() before calling this
routine and pass index to it. Because CPUFreq core now requires to call routines
present in freq_table.c CONFIG_CPU_FREQ_TABLE must be enabled all the time.
This also marks target() interface as deprecated. So, that new drivers avoid
using it. And Documentation is updated accordingly.
It also converts existing .target() to newly defined light weight
.target_index() routine for many driver.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) data structures are specific
to device specific power management, be specific and rename opp_* data
structures in OPP library with dev_pm_opp_* equivalent.
Affected structures are:
struct opp
enum opp_event
Minor checkpatch warning resulting of this change was fixed as well.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.
Affected functions are:
opp_get_voltage
opp_get_freq
opp_get_opp_count
opp_find_freq_exact
opp_find_freq_floor
opp_find_freq_ceil
opp_add
opp_enable
opp_disable
opp_get_notifier
opp_init_cpufreq_table
opp_free_cpufreq_table
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make acpi_cpufreq_init() return error codes when the driver cannot be
registered so that the module doesn't stay useless in memory and so
that acpi_cpufreq_exit() doesn't attempt to unregister things that
have never been registered when the module is unloaded.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The minimum pstate is supposed to be a percentage of the maximum P
state available. Calculate min using max pstate and not the
current max which may have been limited by the user
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch addresses Bug 60727
(https://bugzilla.kernel.org/show_bug.cgi?id=60727)
which was due to the truncation of intermediate values in the
calculations, which causes the code to consistently underestimate the
current cpu frequency, specifically 100% cpu utilization was truncated
down to the setpoint of 97%. This patch fixes the problem by keeping
the results of all intermediate calculations as fixed point numbers
rather scaling them back and forth between integers and fixed point.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60727
Signed-off-by: Brennan Shacklett <bpshacklett@gmail.com>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_set_policy() has been changed to origin __cpufreq_set_policy()
and policy->lock has been converted to rewrite lock by commit 5a01f2.
So remove the comment.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the exynos4210_set_apll() function, the APLL frequency is set with
direct register manipulation.
Such approach is not allowed in the common clock framework. The frequency
is changed, but the corresponding clock value is not updated. This causes
wrong frequency read from cpufreq's cpuinfo_cur_freq sysfs attribute.
Also direct manipulation with PLL's S parameter has been removed. It is
already done at PLL35xx code.
Tested at:
- Exynos4210 - Trats board (linux 3.12-rc4)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the exynos4x12_set_apll() function, the APLL frequency is set with
direct register manipulation.
Such approach is not allowed in the common clock framework. The frequency
is changed, but the corresponding clock value is not updated. This causes
wrong frequency read from cpufreq's cpuinfo_cur_freq sysfs attribute.
Also direct manipulation with PLL's S parameter has been removed. It is
already done at PLL35xx code.
Tested at:
- Exynos4412 - Trats2 board (linux 3.12-rc4)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function update_policy_cpu() is expected to be called when the policy->cpu
of a cpufreq policy is to be changed: ie., the new CPU nominated to become the
policy->cpu is different from the old one.
Print a warning if it is invoked with new_cpu == old_cpu, since such an
invocation might hint at a faulty logic in the caller.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Enable cpufreq on iMac G5 (iSight) model. Tested with the 2.1 GHz version.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently cpufreq ondemand governor cannot used on older G5 models,
because the transition latency is set to CPUFREQ_ETERNAL. Provide a
value based on a measurement on Xserve G5, which happens to be also the
highest allowed latency.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some functions on switch path use msleep() which is inaccurate, and
depends on HZ. With HZ=100 msleep(1) takes actually over ten times longer.
Using usleep_range() we get more accurate sleeps.
I measured the "pfunc_slewing_done" polling to take 300us at max (on
2.3GHz dual-processor Xserve G5), so using 500us sleep there should
be fine.
With the patch, g5_switch_freq() duration drops from ~50ms to ~10ms on
Xserve with HZ=100.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Calxeda's new ECX-2000 part uses the same cpufreq interface as highbank,
so add it to the driver's compatibility list.
This is a minor change that can safely be applied to the 3.10 and 3.11
stable trees.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, code checks false return value from "regulator_set_voltage"
to show failure message. Modify the code to check proper return
value from "regulator_set_voltage".
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As per coding style, braces {} are not necessary for single statement block
Signed-off-by: Evgeny Kapaev <orener300@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->cur is now set by cpufreq core when cpufreq_driver->get() is defined and
so drivers aren't required to set it. When space_id is ACPI_ADR_SPACE_SYSTEM_IO
for acpi cpufreq driver it doesn't set ->get to a valid function pointer and so
policy->cur is required to be set by driver.
This is already followed in acpi-cpufreq driver. This patch adds a comment
describing why we need to set policy->cur from driver.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The index field of cpufreq_frequency_table has been renamed to
driver_data by commit 5070158 (cpufreq: rename index as driver_data
in cpufreq_frequency_table).
This patch updates the s3c64xx driver to match.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: 3.11+ <stable@vger.kernel.org> # 3.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently clk_get_sys is used with cpu-cluster.<n> as the device id
which is incorrect. It should be connection/consumer ID instead.
It is possible to specify input clock in the cpu device node along
with the optional clock-name. clk_get_sys can't handle that.
This patch replaces clk_get_sys with clk_get to extend support for
clocks specified in the device tree cpu node.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds freq_attr to show a list of exynos5440 scaling
available frequencies through sysfs. Common exynos driver already
supports this attribute.
Signed-off-by: Jungseok Lee <jays.lee@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The expression in line 398 of intel_pstate.c causes the following
warning to be emitted:
drivers/cpufreq/intel_pstate.c:398:3: warning: left shift count >= width of type
which happens because unsigned long is 32-bit on some architectures.
Fix that by using a helper u64 variable and simplify the code
slightly.
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This makes the Integrator cpufreq driver probe from the core
module device tree node through it's registered platforms
device, getting the memory base from the device tree,
remapping it and removing dependencies to <mach/platform.h>
and <mach/hardware.h> by moving the two affected CM
register offsets into the driver.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the system is suspended while max_perf_pct is less than 100 percent
or no_turbo set policy->{min,max} will be set incorrectly with scaled
values which turn the scaled values into hard limits.
References: https://bugzilla.kernel.org/show_bug.cgi?id=61241
Reported-by: Patrick Bartels <petzicus@googlemail.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.9+ <stable@vger.kernel.org> # 3.9+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
This also rearranges the code a bit to make it more sensible. Also removes some
unnecessary checks.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here. This driver wasn't setting transition_latency and so is getting set to 0
by default. Lets mark it explicitly by calling the generic routine with
transition_latency as 0.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CONFIG_CPU_FREQ_TABLE will be always enabled when cpufreq framework is used, as
cpufreq core depends on it. So, we don't need this CONFIG option anymore as it
is not configurable. Remove CONFIG_CPU_FREQ_TABLE and update its users.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many CPUFreq drivers for SMP system (where all cores share same clock lines), do
similar stuff in their ->init() part.
This patch creates a generic routine in cpufreq core which can be used by these
so that we can remove some redundant code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init(). And so we don't need to set policy->cur from driver anymore.
Over that it sets policy->min and max correctly. They were earlier set to
current frequency of CPU but they should be set to max and min freq of cpu.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-By: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Steven Miao <realmz6@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Almost all drivers set policy->cur with current CPU frequency in their ->init()
part. This can be done for all of them at core level and so they wouldn't need
to do it.
This patch adds supporting code in cpufreq core for calling get() after we have
called init() for a policy.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the Tegra driver.
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the speedstep driver.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the spear driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the sparc driver.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the sh driver.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the sc520 driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the sa11x0 driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the s5pv210 driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the s3cx4xx driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the PXA driver.
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the ppc_cbe driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the ppc-corenet driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the powernow driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the pmac driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the pasemi driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the p4-clockmod driver.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the OMAP driver.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the maple driver.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the loongson2 driver.
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the longhaul driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the kirkwood driver.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines for in the imx6q driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the ia64-acpi driver.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the exynos driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-By: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the elanfreq driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the e_powersaver driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines for in the dbx500 driver.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the davinci driver.
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the cris driver.
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the cpufreq-cpu0 driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the blackfin driver.
Cc: Steven Miao <realmz6@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the at32ap driver.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the arm_big_little driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses the generic verify routine in the ACPI driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch introduces generic .attr, .exit() and .verify() cpufreq drivers.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the users of cpufreq_verify_within_limits() calls it for
limiting with min/max from policy->cpuinfo. We can make that code
simple by introducing another routine which will do this for them
automatically.
This patch adds another routine cpufreq_verify_within_cpu_limits()
and updates others to use it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use cpufreq_driver->flags to mark CPUFREQ_HAVE_GOVERNOR_PER_POLICY instead
of a separate field within cpufreq_driver. This will save some bytes of
memory.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Earlier there used to be two functions named __cpufreq_set_policy() and
cpufreq_set_policy(), but now we only have a single routine lets name it
cpufreq_set_policy() instead of __cpufreq_set_policy().
This also removes some invalid comments or fixes some incorrect comments.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_frequency_table_verify() is rewritten here to make it more logical
and efficient.
- merge multiple lines for variable declarations together.
- quit early if any frequency between min/max is found.
- don't call cpufreq_verify_within_limits() in case any valid freq is
found as it is of no use.
- rename the count variable as found and change its type to boolean.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Nobody except cpufreq_remove_dev() calls __cpufreq_remove_dev() and
so we don't need two separate routines here. Merge code from
__cpufreq_remove_dev() into cpufreq_remove_dev() and get rid of
__cpufreq_remove_dev().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As a rule its better not to break string (quoted inside "") in a
print statement even if it crosses 80 column boundary as that may
introduce bugs and so this patch rewrites one of the print statements..
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We don't need a blank line just at start of a block, lets remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some section of kerneldoc comment for __cpufreq_remove_dev() is invalid now.
Remove it.
Suggested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
lock_policy_rwsem_{read|write}() currently has return type of int,
but it always returns zero and hence its return type should be void
instead. This patch makes that change and modifies all of the users
accordingly.
Reported-by: Jon Medhurst<tixy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When sysfs for no_turbo is set, then also some p states in turbo regions
are observed. This patch will set IDA Engage bit when no_turbo is set to
explicitly disengage turbo.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drivers which have an exit path must call cpufreq_frequency_table_put_attr() if
they have called cpufreq_frequency_table_get_attr() in their init path.
This driver was missing this part and is fixed with this patch.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drivers which have an exit path must call cpufreq_frequency_table_put_attr() if
they have called cpufreq_frequency_table_get_attr() in their init path.
This driver was missing this part and is fixed with this patch.
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drivers which have an exit path must call cpufreq_frequency_table_put_attr() if
they have called cpufreq_frequency_table_get_attr() in their init path.
This driver was missing this part and is fixed with this patch.
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drivers which have an exit path must call cpufreq_frequency_table_put_attr() if
they have called cpufreq_frequency_table_get_attr() in their init path.
This driver was missing this part and is fixed with this patch.
Cc: Steven Miao <realmz6@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drivers which have an exit path must call cpufreq_frequency_table_put_attr() if
they have called cpufreq_frequency_table_get_attr() in their init path.
This driver was missing this part and is fixed with this patch.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds a dynamically calculated frequency table to the at32ap driver.
In short the architecture can scale in power of two between a maximum and
minimum frequency. Min, max, and the steps in between are added to the table.
Signed-off-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
->exit() of drivers should call cpufreq_frequency_table_put_attr() if they have
called cpufreq_frequency_table_get_attr() earlier in init() and they aren't
required to validate their cpufreq table in exit by calling
cpufreq_frequency_table_cpuinfo(). Tegra's driver wasn't calling
cpufreq_frequency_table_put_attr() and was calling
cpufreq_frequency_table_cpuinfo() in exit.
Fix both these issues in it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many fields of struct policy are filled by cpufreq core when we call
cpufreq_table_validate_and_show() and so cpufreq driver doesn't need to set them
anymore.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch exposes sa11x0's frequency table to cpufreq core. It always existed
but not as an array frequencies and not in the format cpufreq core wants it to.
Also it was present in the unit of 100kHz earlier which is made consistent with
cpufreq core now, i.e. kHz.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Steven Miao <realmz6@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This exposes frequency table of driver to cpufreq core and is required for core
to guess what the index for a target frequency is, when it calls
cpufreq_frequency_table_target(). And so this driver needs to expose it.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This exposes frequency table of driver to cpufreq core and is required for core
to guess what the index for a target frequency is, when it calls
cpufreq_frequency_table_target(). And so this driver needs to expose it.
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This exposes frequency table of driver to cpufreq core and is required for core
to guess what the index for a target frequency is, when it calls
cpufreq_frequency_table_target(). And so this driver needs to expose it.
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Almost every cpufreq driver is required to validate its frequency table with:
cpufreq_frequency_table_cpuinfo() and then expose it to cpufreq core with:
cpufreq_frequency_table_get_attr().
This patch creates another helper routine cpufreq_table_validate_and_show() that
will do both these steps in a single call and will return 0 for success, error
otherwise.
This also fixes potential bugs in cpufreq drivers where people have called
cpufreq_frequency_table_get_attr() before calling
cpufreq_frequency_table_cpuinfo(), as the later may fail.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since the patch "cpufreq: cpufreq-cpu0: NULL is a valid regulator", cpu_reg
contains an error value if the regulator is not set, instead of NULL.
Accordingly, fix the remaining check for non-NULL cpu_reg.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'clk_round_rate' returns a negative error code upon failure. This
will never get detected by unsigned 'newfreq'. Make it signed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If 'dvfs_info' is NULL (due to devm_kzalloc failure) the failure
error message would try to dereference it. Use 'pdev' instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_get() can be called from external drivers which might not be aware if
cpufreq driver is registered or not. And so we should actually check if cpufreq
driver is registered or not and also if cpufreq is active or disabled, at the
beginning of cpufreq_get().
Otherwise call to lock_policy_rwsem_read() might hit BUG_ON(!policy).
Reported-and-tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the hw supports intel_pstate and acpi_cpufreq, intel_pstate will
get loaded first.
acpi_cpufreq_init() will call acpi_cpufreq_early_init()
and that will allocate perf data and init those perf data in ACPI core,
(that will cover all CPUs). But later it will free them as
cpufreq_register_driver(acpi_cpufreq) will fail as intel_pstate is
already registered
Use cpufreq_get_current_driver() to check if we can skip the
acpi_cpufreq loading.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_has_method() is a new ACPI API introduced to check
the existence of an ACPI control method.
It can be used to replace acpi_get_handle() in the case that
1. the calling function doesn't need the ACPI handle of the control method.
and
2. the calling function doesn't care the reason why the method is unavailable.
Convert acpi_get_handle() to acpi_has_method()
in drivers/cpufreq/pcc_freq.c in this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On systems that support intel_pstate, acpi_cpufreq fails to load, and
udev keeps trying until trace gets filled up and kernel crashes.
The root cause is driver return ret from cpufreq_register_driver(),
because when some other driver takes over before, it will return
EBUSY and then udev will keep trying ...
cpufreq_register_driver() should return EEXIST instead so that the
system can boot without appending intel_pstate=disable and still use
intel_pstate.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit cdc58d602d "cpufreq: imx6q-cpufreq:
remove device tree parsing for cpu nodes" assumed the pdev->dev is set to
cpu0 device in the platform code. But it actually points to the virtual
cpufreq-cpu0 platform device which is not present in the device tree.
Most of the information needed by cpufreq is stored in cpu0 DT node.
So cpu_dev must point to cpu0 device.
This patch fixes the wrong assignment to cpu_dev.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit f837a9b5ab "cpufreq: cpufreq-cpu0:
remove device tree parsing for cpu nodes" assumed the pdev->dev is set to
cpu0 device in the platform code. But it actually points to the virtual
cpufreq-cpu0 platform device which is not present in the device tree.
Most of the information needed by cpufreq is stored in cpu0 DT node.
So cpu_dev must point to cpu0 device.
This patch fixes the wrong assignment to cpu_dev.
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Current code looks like this:
WARN_ON(lock_policy_rwsem_write(cpu));
update_policy_cpu(policy, new_cpu);
unlock_policy_rwsem_write(cpu);
{lock|unlock}_policy_rwsem_write(cpu) takes/releases policy->cpu's rwsem.
Because cpu is changing with the call to update_policy_cpu(), the
unlock_policy_rwsem_write() will release the incorrect lock.
The right solution would be to release the same lock as was taken earlier. Also
update_policy_cpu() was also called from cpufreq_add_dev() without any locks and
so its better if we move this locking to inside update_policy_cpu().
This patch fixes a regression introduced in 3.12 by commit f9ba680d23
(cpufreq: Extract the handover of policy cpu to a helper function).
Reported-and-tested-by: Jon Medhurst<tixy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Mikulas Patocka