The buffer size on nxt200x is not enough:
...
> Dec 20 10:52:04 rich kernel: [ 31.747949] nxt200x: nxt200x_writebytes: i2c wr reg=002c: len=255 is too big!
...
Increase it to 256 bytes.
Reported-by: Rich Freeman <rich0@gentoo.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Value of fec is achieved by the upper nibble bits 6,7 & 8.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Register 0x70 is used to set fec, register 0x76 is used to get fec
Register 0x76 is set to 0x8.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The correct lock values is when bits of the value 0xee are set.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Current setting of symbol rate is not very actuate causing
loss of lock.
Covert temp to u64 and use mclk to calculate from big number.
Calculate symbol rate by dividing symbol rate by 1000 times
1 << 24 and dividing sum by mclk.
Add other symbol rate settings to function registers 0xa0-0xa3.
In set_frontend add changes to register 0xf1 this must be done
prior call to fe_reset. Register 0x00 doesn't need a second
write of 0x1
Applied after patch
m88rs2000: add m88rs2000_set_carrieroffset
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set the carrier offset correctly using the default mclk values.
Add function m88rs2000_get_mclk to calculate the mclk value
against crystal frequency which will later be used for
other functions.
Add function m88rs2000_set_carrieroffset to calculate
and set the offset value.
variable offset becomes a signed value.
Register 0x86 is set the appropriate value according to
remainder value of frequency % 192857 calculation as
shown.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by kbuild test robot <fengguang.wu@intel.com>:
with a random config:
drivers/built-in.o: In function `dib8000_get_time_us.isra.16':
>> dib8000.c:(.text+0x3075aa): undefined reference to `__udivdi3'
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* remove Free Software Foundation postal address
* add one pair of parenthesis
* use sizeof(*foo), not sizeof(struct foo)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adapter is locked by I2C core already. Use unlocked i2c_transfer()
version __i2c_transfer() to avoid deadlock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Write inittab using reg address auto-increment in order to reduce
I/O a little bit.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reg 0x56 should be programmed to 0x01. Add default to inittab.
Reported-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Optimal AGC is highly depended on used RF tuner and due to that
it is already included to chip configuration. However, inittab
has default AGC value, which was later replaced by one from config.
Add also comment to all chip configuration options about default
values and if those are needed to set or not.
Reported-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DIV_ROUND_CLOSEST does the job and looks better.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Switch standard I2C adapter to muxed I2C adapter.
David reported that I2C adapter implementation caused deadlock.
I discussed with Jean and he suggested to implement it as a
multiplexed i2c adapter because tuner I2C bus could be seen like
own I2C segment.
Reported-by: David Howells <dhowells@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I2C transfer were using dynamic stack allocation. Get rid of it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PER/UCB statistics are collected once on each 1 second.
However, it doesn't provide the total number of packets
needed to calculate PER.
Yet, as we know the bit rate, it is possible to estimate
such number. So, do it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On dib8000, the BER statistics are updated on every 1.25e6 bits.
Adjust the code to only update the statistics after having it
done.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On dib8000, the block error count is a monotonic 32 bits register.
With DVBv5 stats, we use a 64 bits counter, that it is reset
when a new channel is tuned.
Change the UCB counting start from 0 and to be returned with
64 bits, just like the API requests.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Use multiple linear segments to better interpolate the dBm
for the signal strength.
The table that converts from linear strength to dB was
empirically determinated with the help of a signal generator
(DTA-2111).
The entries from -35dBm to -22.5dBm were taken using just
the signal generator and the board.
For the entries from -36dBm to -51dBm, a 16 dB tap was used,
in order to extend its range.
Signals below to -51dBm are just linearly interpolated.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Better to have Signal strength in dB.
This takes a very rough estimation for the signal strength,
that was calibrated using a Dektec DTA-2111 Gold RF generator
and a Pixelview dib8076 stick.
It estimates the signal strength using a linear equation where:
- the max is -22.5 dBm, with returns 55953
- the min is -35.0 dBm, with returns 50110
With -22dBm, the signal strengh is returned as 65535.
Unfortunately, the min strength generated with DTA-2111 is
-35dBm.
It should be noticed that approximating it by a linear equation
is not right. I should probably be splitting it into 0.5 dB
linear segments, in order to get a higher precision, just like
it is done on mb86a20s, but that would force me to add some
attenuators, in order to get dB levels below -35dBm, which is,
btw, strong enough to get signal lock.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
The advantage of DVBv5 stats is that it allows adding proper
scales to all measures. use it for this frontend.
This patch adds a basic set of stats, basically cloning what's already
provided by DVBv3 API. Latter patches will improve it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On ISDB-T, the valid values for interleaving are 0, 1, 2 and 4.
While the first 3 are properly reported, the last one is reported
as 3 instead. Fix it.
Tested with a Dektec DTA-2111 RF generator.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
The logic that detects if auto search mode should be used is too
complex.
Also, it doesn't cover all cases, as the dib8000_tune logic
requires either auto mode or a fully specified manual mode.
So, move it to a separate function and add some extra debug
data to help identifying when it falled back to auto mode,
because the manual settings are invalid.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Both dvbv5-scan and dvbv5-zap tools call FE_GET_PROPERTY inside the
loop that checks for stats. If the frontend doesn't support DVBv5, it
falls back to call the DVBv5 stats APIs(FE_READ_BER, FE_READ_SIGNAL,
FE_READ_SNR and FE_READ_UNCORRECTED_BLOCKS).
A call to FE_GET_PROPERTY makes dvb-frontend core to call get_frontend().
However, due to a race condition on dib8000 between dib8000_get_frontend
and dib8000_tune, if get_frontend occurs too early, it causes the
tune state machine to fail and not get any lock.
This patch adds a workaround code that makes get_frontend() to just
return if none of the frontends have a SYNC. This change fixed the issue
with dvbv5-scan/dvbv5-zap, but a fine-tuned logic might be needed in
the future, when we implement DVBv5 stats on this frontend.
The procedure to test the bug and the fix is the one below:
1) tune into a non-existing frequency with:
$ dvbv5-zap -I dvbv5 -c non_existing_freqs -m 679142857 -t3
2) tune/lock into an existing frequency with:
$ dvbv5-zap -I dvbv5 -c isdb-test -m 479142857
or
$ dvbv5-scan isdb-test
In this case, 679 MHz carrier doesn't exist. Only 479 MHz does.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
As the dvb-frontend kthread can be called anytime, it can race
with some get status ioctl. So, it seems better to avoid one to
race with the other while reading a 32 bits register.
I can't see any other reason for having a mutex there at I2C, except
to provide such kind of protection, as the I2C core already has a
mutex to protect I2C transfers.
Note: instead of this approach, it could eventually remove the dib8000
specific mutex for it, and either group the 4 ops into one xfer or
to manually control the I2C mutex. The main advantage of the current
approach is that the changes are smaller and more puntual.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Commit 173a64cb3f broke support for some dib807x versions.
Fix it by providing backward compatibility with the older versions.
[mkrufky@linuxtv.org: conflict handling and CodingStyle fixes]
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Merge the media fixes merged upstream for v3.13-rc4
* upstream-fixes: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch should fix/enhance the set_voltage function for
the cx24117 demodulator.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the complete list of all the commands known
for the cx24117 demodulator.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver did not work anymore since I2C has gone broken due
to recent commit:
commit 37ebaf6891
[media] dvb-frontends: Don't use dynamic static allocation
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@vger.kernel.org
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stv090x.c:750:1: warning: 'stv090x_write_regs.constprop.6' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stv0367.c:791:1: warning: 'stv0367_writeregs.constprop.4' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stb0899_drv.c:540:1: warning: 'stb0899_write_regs' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/af9013.c:77:1: warning: 'af9013_wr_regs_i2c' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/af9033.c:188:1: warning: 'af9033_wr_reg_val_tab' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/af9033.c:68:1: warning: 'af9033_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/bcm3510.c:230:1: warning: 'bcm3510_do_hab_cmd' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/cxd2820r_core.c:84:1: warning: 'cxd2820r_rd_regs_i2c.isra.1' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/rtl2830.c:56:1: warning: 'rtl2830_wr' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/rtl2832.c:187:1: warning: 'rtl2832_wr' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda10071.c:52:1: warning: 'tda10071_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda10071.c:84:1: warning: 'tda10071_rd_regs' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/bcm3510.c:230:1: warning: 'bcm3510_do_hab_cmd' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/itd1000.c:69:1: warning: 'itd1000_write_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/mt312.c:126:1: warning: 'mt312_write' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/nxt200x.c:111:1: warning: 'nxt200x_writebytes' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stb6100.c:216:1: warning: 'stb6100_write_reg_range.constprop.3' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stv6110.c:98:1: warning: 'stv6110_write_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stv6110x.c:85:1: warning: 'stv6110x_write_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda18271c2dd.c:147:1: warning: 'WriteRegs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/zl10039.c:119:1: warning: 'zl10039_write' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/s5h1420.c:851:1: warning: 's5h1420_tuner_i2c_tuner_xfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In the specific case of this frontend, only ttpci uses it. The maximum
number of messages there is two, on I2C read operations. As the logic
can add an extra operation, change the size to 3.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use R820T config for R828D too as those are about same tuner.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxk_hard.c:1086:62: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxk_hard.c:2784:63: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxd_hard.c:1017:70: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:1038:69: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:2836:33: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:2972:30: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These aren't necessary after switch and while statements.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch will fix the situation where the mutex was left in a
locked state if for some reason the FE init failed.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab