When the audio stream is paused or suspended we stop the sDMA and when it
is unpaused/resumed we start the channel without reconfiguring it.
The omap_dma_stop() clears the link configuration when we pause the dma, but
it is not setting it back on start. This will result only one audio buffer
to be played back and the DMA will stop, since the linking is disabled.
We need to restore the CLINK_CTRL register in case of resume.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add mb() call to resume path to ensure the necessary barrier.
Resume can happen after waking up from suspend for example.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Braswell SoC has two DMA controllers for LPSS. This patch adds them to
supported list in the PCI driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On BayTrail platform DMA is not functional in the PCI mode, whereby it always
failed and exit at the point when it tries to get a clock. It causes the PCI
mode probe to exit with the error message:
dw_dmac_pci: probe of 0000:00:1e.0 failed with error -2
This patch moves clock operations to where it belongs to. Thus, the clock is
provided only in ACPI / non-PCI cases.
Reported-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The introduced filter function would be reused in the ACPI and DT cases since
in those cases we have to apply mandatory data to the requested channel. Thus,
patch moves platform driver to use it in that case.
The function unlikely can't be used by users of the driver due to an implicit
dependency to the dw_dmac_core module.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of one request line member let's use both source and destination ones.
Usually we have no such hardware except Atmel MMC controller found on AVR32
platform (see arch/avr32/mach-at32ap/at32ap700x.c and
drivers/mmc/host/atmel-mci.c).
This patch removes slave_id usage since it'll be removed from the generic
structure in later. This breaks the non-ACPI / non-DT cases for the users of
the driver, i.e. SPI and HSUART. However, these cases mean only PCI enumerated
devices for now, which is anyway broken (considering more than one DMA
controller in the system) and this patch series is intended to fix that
eventually.
The ACPI and DT cases shall be aware of the channel direction when setting
request lines, but this is a minor problem that would be addressed in future.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of exposing the possibility to set DMA registers CFG_HI and CFG_LO
strict user to provide handshake interfaces explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is a common storage for platform data related structures and definitions
inside kernel source tree. The patch moves file from include/linux to
include/linux/platform_data and renames it acoordingly. The users are also
updated.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[For the arch/avr32/.* and .*sound/atmel.*]
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need to make sure to deqeueue the descriptor from the active list before
we call vchan_cookie_complete(). Also we need obviously only set chan->desc
to NULL after we stopped using it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
add DMA_PREP_INTERRUPT flag to support no_period_wakeup, in which
user space app doesn't want audio interrupt to wake up audio threads.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We can't annotate probe functions as __init since binding can occur at
any time, not just during kernel init.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case of no corresponding slave ID, the audmapp_set_slave() returns
-ENXIO same as sh_dmae_set_slave() of shdmac.c.
DMAEngine might return wrong channel without this patch
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Jun Watanabe <jun.watanabe.ue@renesas.com>,
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When we fail to allocate memory for thread->srcs or thread->dsts and src_cnt or
dst_cnt great than 1 we leak memory on error path. This patch fixes the issue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
To be future-proof and for better readability the time comparisons are modified
to use time_before_jiffies() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
[djbw: use time_before_jiffies() to make argument order more clear]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Levente Kurusa <lkurusa@redhat.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Several dma drivers calls tasklet_kill() in remove function. This is done
because all running tasklets should be killed on remove. This is missing
in imx sdma driver, so adding tasklet_kill() in sdma_remove function.
Signed-off-by: Vignesh Raman <Vignesh_Raman@mentor.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently there is no module_exit declared in SDMA driver, so that once
sdma module is inserted, it's shown with permanent attribute by lsmod,
and it can't be removed.
Use module_platform_driver to register/unregister SDMA driver and modify
SDMA's remove operation, to make SDMA driver possible to be removed.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull slave-dma updates from Vinod Koul:
"Some notable changes are:
- new driver for AMBA AXI NBPF by Guennadi
- new driver for sun6i controller by Maxime
- pl330 drivers fixes from Lar's
- sh-dma updates and fixes from Laurent, Geert and Kuninori
- Documentation updates from Geert
- drivers fixes and updates spread over dw, edma, freescale, mpc512x
etc.."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (72 commits)
dmaengine: sun6i: depends on RESET_CONTROLLER
dma: at_hdmac: fix invalid remaining bytes detection
dmaengine: nbpfaxi: don't build this driver where it cannot be used
dmaengine: nbpf_error_get_channel() can be static
dma: pl08x: Use correct specifier for size_t values
dmaengine: Remove the context argument to the prep_dma_cyclic operation
dmaengine: nbpfaxi: convert to tasklet
dmaengine: nbpfaxi: fix a theoretical race
dmaengine: add a driver for AMBA AXI NBPF DMAC IP cores
dmaengine: add device tree binding documentation for the nbpfaxi driver
dmaengine: edma: Do not register second device when booted with DT
dmaengine: edma: Do not change the error code returned from edma_alloc_slot
dmaengine: rcar-dmac: Add device tree bindings documentation
dmaengine: shdma: Allocate cyclic sg list dynamically
dmaengine: shdma: Make channel filter ignore unrelated devices
dmaengine: sh: Rework Kconfig and Makefile
dmaengine: sun6i: Fix memory leaks
dmaengine: sun6i: Free the interrupt before killing the tasklet
dmaengine: sun6i: Remove switch statement from buswidth convertion routine
dmaengine: of: kconfig: select DMA_ENGINE when DMA_OF is selected
...
Fixes a compilation error when RESET_CONTROLLER is not enabled in the
configuration.
drivers/dma/sun6i-dma.c: In function 'sun6i_dma_probe':
drivers/dma/sun6i-dma.c:911:2: error: implicit declaration of function 'devm_reset_control_get' [-Werror=implicit-function-declaration]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Found using smatch:
drivers/dma/at_hdmac.c:299 atc_get_bytes_left() warn: unsigned
'atchan->remain_desc' is never less than zero.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Although this driver doesn't have any explicit compile-time architecture
dependencies, it is better not to bloat kernels on those platforms, where
this driver isn't needed, unless a compile test is being performed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There've been many updates in ASoC side at this time, especially the
framework enhancement for multiple CODECs on a single DAI and more
componentization works. The only major change in ALSA core is the
addition of timestamp type in sw_params field. This should behave in
backward compatible way. Other than that, there are lots of small
changes and new drivers in wide range, including a large code cut in
HD-audio driver for deprecated static quirks. Some highlights are
below:
ALSA Core:
- Add the new timestamp type field to sw_params to choose
MONOTONIC_RAW type
HD-audio:
- Continued conversion to standard printk macros, generic code
cleanups
- Removal of obsoleted static quirk codes for Conexant and C-Media
codecs
- Fixups for HP Envy TS, Dell XPS 15, HP and Dell mute/mic LED,
Gigabyte BXBT-2807 mobo
- Intel Braswell support
ASoC:
- Support for multiple CODECs attached to a single DAI, enabling
systems with for example multiple DAC/speaker drivers on a single
link, contributed by Benoit Cousson based on work from Misael Lopez
Cruz
- Support for byte controls larger than 256 bytes based on the use of
TLVs contributed by Omair Mohammed Abdullah
- More componentisation work from Lars-Peter Clausen
- The remainder of the conversions of CODEC drivers to params_width()
by Mark Brown
- Drivers for Cirrus Logic CS4265, Freescale i.MX ASRC blocks, Realtek
RT286 and RT5670, Rockchip RK3xxx I2S controllers and Texas
Instruments TAS2552
- Lots of updates and fixes, especially to the DaVinci, Intel,
Freescale, Realtek, and rcar drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=RL72
-----END PGP SIGNATURE-----
Merge tag 'sound-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There've been many updates in ASoC side at this time, especially the
framework enhancement for multiple CODECs on a single DAI and more
componentization works.
The only major change in ALSA core is the addition of timestamp type
in sw_params field. This should behave in backward compatible way.
Other than that, there are lots of small changes and new drivers in
wide range, including a large code cut in HD-audio driver for
deprecated static quirks. Some highlights are below:
ALSA Core:
- Add the new timestamp type field to sw_params to choose
MONOTONIC_RAW type
HD-audio:
- Continued conversion to standard printk macros, generic code
cleanups
- Removal of obsoleted static quirk codes for Conexant and C-Media
codecs
- Fixups for HP Envy TS, Dell XPS 15, HP and Dell mute/mic LED,
Gigabyte BXBT-2807 mobo
- Intel Braswell support
ASoC:
- Support for multiple CODECs attached to a single DAI, enabling
systems with for example multiple DAC/speaker drivers on a single
link, contributed by Benoit Cousson based on work from Misael Lopez
Cruz
- Support for byte controls larger than 256 bytes based on the use of
TLVs contributed by Omair Mohammed Abdullah
- More componentisation work from Lars-Peter Clausen
- The remainder of the conversions of CODEC drivers to params_width()
by Mark Brown
- Drivers for Cirrus Logic CS4265, Freescale i.MX ASRC blocks,
Realtek RT286 and RT5670, Rockchip RK3xxx I2S controllers and Texas
Instruments TAS2552
- Lots of updates and fixes, especially to the DaVinci, Intel,
Freescale, Realtek, and rcar drivers"
* tag 'sound-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (402 commits)
ALSA: usb-audio: Whitespace cleanups for sound/usb/midi.*
ALSA: usb-audio: Respond to suspend and resume callbacks for MIDI input
sound/oss/pss: Remove typedefs pss_mixerdata and pss_confdata
sound/oss/opl3: Remove typedef opl_devinfo
ALSA: fireworks: fix specifiers in format strings for propper output
ASoC: imx-audmux: Use uintptr_t for port numbers
ASoC: davinci: Enable menuconfig entry for McASP
ASoC: fsl_asrc: Don't access members of config before checking it
ASoC: fsl_sarc_dma: Check pair before using it
ASoC: adau1977: Fix truncation warning on 64 bit architectures
ALSA: virtuoso: add Xonar Essence STX II support
ALSA: riptide: fix %d confusingly prefixed with 0x in format strings
ALSA: fireworks: fix %d confusingly prefixed with 0x in format strings
ALSA: hda - add codec ID for Braswell display audio codec
ALSA: hda - add PCI IDs for Intel Braswell
ALSA: usb-audio: Adjust Gamecom 780 volume level
ALSA: usb-audio: improve dmesg source grepability
ASoC: rt5670: Fix duplicate const warnings
ASoC: rt5670: Staticise non-exported symbols
ASoC: Intel: update stream only on stream IPC msgs
...
When printing size_t values we should use the %zd or %zx format specifier
in order to ensure the value is displayed correctly and avoid warnings from
sparse.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The argument is always set to NULL and never used. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is common among dmaengine drivers to use a tasklet for bottom half
interrupt processing. Convert nbpfaxi to do the same.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A race possibility exists if a DMA slave driver tries to free channel
resources witout waiting for all transfers to complete and without
explicitly terminating all requests. In such a case the IRQ processing
thread can race with .device_free_chan_resources(). To fix this race empty
all descriptor lists before freeing descriptor cache.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds a driver for NBPF DMAC IP cores from Renesas, designed for
the AMBA AXI bus.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DT boot does not yet support more than one edma device. To avoid issues at
runtime we should not register the second device when the kernel is booted
with DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case of edma_alloc_slot() failure during probe we should return the error
unchanged to make debugging easier.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sg list used to prepare cyclic DMA descriptors is currently
allocated statically on the stack as an array of 32 elements. This makes
the shdma_prep_dma_cyclic() function consume a lot of stack space, as
reported by the compiler:
drivers/dma/sh/shdma-base.c: In function ‘shdma_prep_dma_cyclic’:
drivers/dma/sh/shdma-base.c:715:1: warning: the frame size of 1056 bytes
is larger than 1024 bytes [-Wframe-larger-than=]
Given the limited Linux kernel stack size, this could lead to stack
overflows. Fix the problem by allocating the sg list dynamically.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The shdma_chan_filter() function relies on the DMA channel being
embedded in an shdma_chan structure. If this assumption isn't true, for
instance when the system contains DMA channels supported by an unrelated
driver, the function will crash.
Avoid this by returning false directly when the channel belongs to an
unrelated device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Separate helpers and drivers in the Kconfig and Makefile to improve
readability and move the CONFIG_OF dependency from the Makefile to
Kconfig.
[pebolle@tiscali.nl: reported need to rename SHDMA_R8A73A4 instances]
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: squashed rename of SHDMA_R8A73A4 instances]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sun6i_dma_prep_memcpy and sun6i_dma_prep_slave_sg functions were both
leaking the descriptor they allocated if an error was happening after a
successful dma_pool_alloc call.
It also fixes a memleak that was happening in the scatter gather list
traversal, that was allocating as much descriptor as there was scatter gather
items, but only freeing the current descriptor if an error was to arise.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There's still a small window between the call to sun6i_kill_tasklet and the end
of the driver remove function where a spurious interrupt might trigger, and
start using deallocated resources.
Replace the call to synchronize_irq by a free_irq, so that we're sure that we
won't get any further interrupts when we're deallocating resources.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the conversion routine is quite trivial, we don't need this switch, and
we can just use a simple calculation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Select DMA_ENGINE when DMA_OF is selected since
of_dma_xlate_by_chan_id() from drivers/dma/of-dma.c uses
dma_get_slave_channel() from drivers/dma/dmaengine.c
This resolves error reported:
drivers/built-in.o: In function `of_dma_xlate_by_chan_id':
drivers/dma/of-dma.c:253: undefined reference to `dma_get_slave_channel'
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Move the DMA channel used in cyclic mode (audio) to the highest priority
event queue which helps to reduce audio problems.
When the channel is terminated, move it back to the default queue.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the client (audio) does not request interrupts for every period we can
disable them.
With updated audio driver stack we can play audio w/o the need to process
any edma interrupts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The edma can report accurate DMA position so update the residue_granularity
to DMA_RESIDUE_GRANULARITY_BURST.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sg_dma_len() returns unsigned int but we had driver print it as %zu, use
%u as documented in Documentation/printk-formats.txt
drivers/dma/sun6i-dma.c: In function ‘sun6i_dma_prep_slave_sg’:
drivers/dma/sun6i-dma.c:643: warning: format ‘%zu’ expects type ‘size_t’,
but argument 8 has type ‘unsigned int’
drivers/dma/sun6i-dma.c:661: warning: format ‘%zu’ expects type ‘size_t’,
but argument 8 has type ‘unsigned int’
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the driver defined COMPILE_TEST, it gets compiled for different arch's
The driver uses __virt_to_phys() insteadof virt_to_phys, so replace it
drivers/dma/sun6i-dma.c: In function ‘sun6i_dma_dump_chan_regs’:
drivers/dma/sun6i-dma.c:203: error: implicit declaration of function '__virt_to_phys'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Register the controller for device tree based lookup of DMA channels
(non-fatal for backwards compatibility with older device trees) and
provide the '#dma-cells' property in the shared mpc5121.dtsi file
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds a new common OF dma xlate callback function which will match a
channel by it's id. The binding expects one integer argument which it will use to
lookup the channel by the id.
Unlike of_dma_simple_xlate this function is able to handle a system with
multiple DMA controllers. When registering the of dma provider with
of_dma_controller_register a pointer to the dma_device struct which is
associated with the dt node needs to passed as the data parameter.
New function will use this pointer to match only channels which belong to the
specified DMA controller.
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Allwinner A31 has a 16 channels DMA controller that it shares with the
newer A23. Although sharing some similarities with the DMA controller of the
older Allwinner SoCs, it's significantly different, I don't expect it to be
possible to share the driver for these two.
The A31 Controller is able to memory-to-memory or memory-to-device transfers on
the 16 channels in parallel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit - 653e67f7e5: "dmaengine: inherit debug settings from the subsystem
for subdirectories" introduced debug option for subdirectories too
This exposed issue with ipu driver not using return value
For now just warn users about it
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Per license_is_gpl_compatible(), the MODULE_LICENSE() string for GPL v2 is
"GPL v2", not "GPLv2". Use "GPL v2" so this module doesn't taint the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Shared Peripheral ASRC, running on SPBA, needs to use shp sciprts for
DMA transfer. So this patch just adds a new DMATYPE for it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The filter() function is currently called by xlate() while it transfers
imx_dma_data as a local variable to the filter() but releases the data
right after returning a DMA channel pointer, which results chan->private
pointing an invalid memory space.
So this patch just stores the imx_dma_data into sdmac to make usre the
private pointer valid as long as the channel exists.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 6079d38 ("dmaengine: pl330: Remove useless xfer_cb indirection")
removed the __callback() function which created an unnecessary level of
indirection to execute the tranfer callback .xfer_cb
Unfortunately the commit also changed the semantics slightly since that
function used to check if the request was not NULL before attempting to
execute the callback function. Not checking this could lead to a kernel
NULL pointer dereference error.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Select DMA_ENGINE instead of DMAENGINE and delete the default
line as the default is 'n' anyways.
Link: https://lkml.org/lkml/2014/7/14/90
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accordingly to discussion [1] and followed up documentation the DMA controller
driver shouldn't start any DMA operations when dmaengine_submit() is called.
This patch fixes the workflow in dw_dmac driver to follow the documentation.
[1] http://www.spinics.net/lists/arm-kernel/msg125987.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It would be useful to know when the first descriptor in the queue is started
along with its cookie.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have a duplicate code which starts first descriptor in the queue. Let's make
this as a separate helper that can be used in future as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330_chan_ctrl() function has 3 internal code paths which, except for the
locking, do not share any code outside of their sections. One code path is never
exercised and can be removed. The other two are mostly just forwards to the
_start() and _stop() calls. This patch modifies the code to instead of going via
pl330_chan_ctrl() to call _start() and _stop() directly. This allows to
completely remove pl330_chan_ctrl().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of storing a special instruction in the command buffer to mark a request
as currently unused just set the descriptor field to NULL.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330_req struct is embedded into the dma_pl330_desc struct. But half of the
pl330_req struct are pointers to other fields of the dma_pl330_desc struct it is
embedded to. By directly embedding the fields from the pl330_req struct into the
dma_pl330_desc struct and reworking the code to work with the dma_pl330_desc
struct those pointers can be eliminated. This slightly simplifies the code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Both the dma_pl330_dmac and the pl330_dmac struct have the same lifetime and the
separation of them is a relict of this having been two different drivers in the
past. Merging them into one struct makes the code a bit simpler as it for
example allows to remove the pointers going back and forth between the two
structs.
While we are at it also directly embed the pl330_info struct into the
pl330_dmac struct as this allows to remove some more redundant fields.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we keep a pointer to the manager thread it is fairly easy to check if a
thread is the manager thread.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We know that we do not create invalid ccr settings in this driver. There is no
need to validate them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330_chid field of the dma_pl330_chan struct always holds a pointer to the
thread that is associated with the channel. Changing its type form void * to
struct pl330_thread makes things more type safe and removes the need for
unnecessary typecasts. While we are at it also rename the field from the cryptic
pl330_chid to thread.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The xfer_cb callback of the pl330_req struct is always set to the same function.
This adds an unnecessary step of indirection. Instead just call the callback
function directly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mc_len is initialized but its value is never read again, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The next field is always NULL, so we can remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dmac_reset() callaback of the pl330_info struct is always set to NULL, so
remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330_chanstatus struct is completely unused, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The settings for destination and source cache control are exactly the same. This
patch removes the duplicated enum and uses the same for both destination and
source cache control.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330 driver has the custom pl330_reqtype enum which has the same possible
settings as the generic dma_transfer_direction enum. Switching over to the
generic enum internally makes it possible to directly initialize it from the
transfer request direction.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
To be able to see debug messages during boot, enable the debug settings
from Kconfig also for drivers in subdirectories.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for end of transaction (EOT) and notify when done (NWD)
hardware descriptor flags.
The EOT flag requests that the peripheral assert an end of transaction interrupt
when that descriptor is complete. It also results in special signaling protocol
that is used between the attached peripheral and the core using the DMA
controller. Clients will specify DMA_PREP_INTERRUPT to enable this flag.
The NWD flag requests that the peripheral wait until the data has been fully
processed by the peripheral before moving on to the next descriptor. Clients
will specify DMA_PREP_FENCE to enable this flag.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix the potential risk when enable config NET_DMA and ASYNC_TX. Async_tx is
lack of support in current release process of dma descriptor, all descriptors
will be released whatever is acked or no-acked by async_tx, so there is a
potential race condition when dma engine is uesd by others clients (e.g. when
enable NET_DMA to offload TCP).
In our case, a race condition which is raised when use both of talitos and
dmaengine to offload xor is because napi scheduler will sync all pending
requests in dma channels, it affects the process of raid operations due to
ack_tx is not checked in fsl dma. The no-acked descriptor is freed which is
submitted just now, as a dependent tx, this freed descriptor trigger
BUG_ON(async_tx_test_ack(depend_tx)) in async_tx_submit().
TASK = ee1a94a0[1390] 'md0_raid5' THREAD: ecf40000 CPU: 0
GPR00: 00000001 ecf41ca0 ee44/921a94a0 0000003f 00000001 c00593e4 00000000 00000001
GPR08: 00000000 a7a7a7a7 00000001 045/920000002 42028042 100a38d4 ed576d98 00000000
GPR16: ed5a11b0 00000000 2b162000 00000200 046/920000000 2d555000 ed3015e8 c15a7aa0
GPR24: 00000000 c155fc40 00000000 ecb63220 ecf41d28 e47/92f640bb0 ef640c30 ecf41ca0
NIP [c02b048c] async_tx_submit+0x6c/0x2b4
LR [c02b068c] async_tx_submit+0x26c/0x2b4
Call Trace:
[ecf41ca0] [c02b068c] async_tx_submit+0x26c/0x2b448/92 (unreliable)
[ecf41cd0] [c02b0a4c] async_memcpy+0x240/0x25c
[ecf41d20] [c0421064] async_copy_data+0xa0/0x17c
[ecf41d70] [c0421cf4] __raid_run_ops+0x874/0xe10
[ecf41df0] [c0426ee4] handle_stripe+0x820/0x25e8
[ecf41e90] [c0429080] raid5d+0x3d4/0x5b4
[ecf41f40] [c04329b8] md_thread+0x138/0x16c
[ecf41f90] [c008277c] kthread+0x8c/0x90
[ecf41ff0] [c0011630] kernel_thread+0x4c/0x68
Another modification in this patch is the change of completed descriptors,
there is a potential risk which caused by exception interrupt, all descriptors
in ld_running list are seemed completed when an interrupt raised, it works fine
under normal condition, but if there is an exception occured, it cannot work as
our excepted. Hardware should not be depend on s/w list, the right way is to
read current descriptor address register to find the last completed descriptor.
If an interrupt is raised by an error, all descriptors in ld_running should not
be seemed finished, or these unfinished descriptors in ld_running will be
released wrongly.
A simple way to reproduce:
Enable dmatest first, then insert some bad descriptors which can trigger
Programming Error interrupts before the good descriptors. Last, the good
descriptors will be freed before they are processsed because of the exception
intrerrupt.
Note: the bad descriptors are only for simulating an exception interrupt. This
case can illustrate the potential risk in current fsl-dma very well.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Qiang Liu <qiang.liu@freescale.com>
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The usage of spin_lock_irqsave() is a stronger locking mechanism than is
required throughout the driver. The minimum locking required should be used
instead. Interrupts will be turned off and context will be saved, it is
unnecessary to use irqsave.
This patch changes all instances of spin_lock_irqsave() to spin_lock_bh(). All
manipulation of protected fields is done using tasklet context or weaker, which
makes spin_lock_bh() the correct choice.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Qiang Liu <qiang.liu@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This resolves a number of merge issues with changes in this tree and
Linus's tree at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch implements DMA Engine API for DMA controller on MIC X100
Coprocessors. DMA h/w is shared between host and card s/w.
Channels 0 to 3 are used by host and 4 to 7 are used by card.
Since the DMA device doesn't show up as PCIe device, a virtual bus called mic
bus is created and virtual devices are added on that bus to follow device model.
Allowed dma transfer directions are host to card, card to host and card to card.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Siva Yerramreddy <yshivakrishna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds DT support to Audio DMAC peri peri driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: Do not add trailing blank line to rcar-audmapp.txt]
[horms+renesas@verge.net.au: squashed patch to add NULL terminater to audmapp_of_match]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Also add a few definitions that were missing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current audmapp driver is keeping audmapp_slave_config
for each channeles, but, nessasary information is only "chcr".
Current style (= keeping audmapp_slave_config) is
not good match for DT support.
Keep "chcr" instead of audmapp_slave_config
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current .set_slave callback did nothing,
since it assumed src/dst address come from platform settings.
But, it isn't good match to DT probing.
This patch enables .set_slave callback to this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
eDMA can be configured for 3bytes word size for source and destination.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
I received a report this morning from one of the Novena developers that
the behaviour of the iMX6 ASoC codec driver (using imx-pcm-dma.c) was
sub-optimal under high system load.
While there are issues relating to system load remaining, upon reviewing
the ASoC imx-pcm-dma.c driver, it was noticed that it not using the
residue support, because SDMA doesn't support it. This has the effect
that SDMA has to make multiple calls into the ASoC and ALSA code, one
for each period.
Since ALSA's snd_pcm_elapsed() does not need to be called multiple times
and it is entirely sufficient to call it once to update ALSA with the
current buffer position via the pointer method, we can do better here.
We can also avoid stopping the DMA entirely, just like real cyclic DMA
implementations behave. While this means that we replay some old samples,
this is a nicer behaviour than having audio stop and restart.
The changes to achieve this are relatively minor - imx-sdma.c can track
where the DMA is to the nearest descriptor boundary - it does this
already when deciding how many callbacks to issue. In doing this,
buf_tail always points at the descriptor which will complete next.
The residue is defined by the bytes remaining to the end of the buffer,
when the buffer is viewed as a single block of memory [start...end].
So, when we start out, there's a full buffer worth of residue, and this
counts down as we approach the end of the buffer, eventually becoming
zero at the end, before returning to the full buffer worth when we
wrap back to the start.
Moving the walking of the descriptors into the interrupt handler means
that we can update the BD_DONE flag at interrupt time, thus avoiding
a delayed tasklet stopping the cyclic DMA.
This means that the residue can be calculated from (total descriptors -
buf_tail) * descriptor size. This is what the change below does. We
update imx-pcm-dma.c to remove the NO_RESIDUE flag since we now provide
the residue.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When a 0-length packet is received on the bus, desc->pd0 yields 1,
which confuses the driver's users. This information is clearly wrong
and not in accordance to the datasheet, but it's been observed on an
AM335x board, very reproducible.
Fix this by looking at bit 19 in PD2 of the completed packet. This bit
will tell us if a zero-length packet was received on a queue. If it's
set, ignore the value in PD0 and report a total length of 0 instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dynamic stack allocation in kernel is considered bad as kernel stack is low and
we get warns on few archs as reported by kbuild test robot
>> drivers/dma/sh/shdma-base.c:671:32: sparse: Variable length array is used.
>> drivers/dma/sh/shdma-base.c:701:1: warning: 'shdma_prep_dma_cyclic' uses
>> dynamic stack allocation [enabled by default]
Fix this by making a static array of 32 which should be sufficient for
shdma_prep_dma_cyclic which only user in kernel is audio and 32 periods for
audio seems quite sufficient atm
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As documented in Documentation/printk-formats.txt we should use %zu/%zx
specifiers for size_t type variables for the code to compile on different
architectures. This is uncovered as COMPILE_TEST has been enabled recently for
this driver
drivers/dma/sh/shdma-base.c: In function 'shdma_prep_dma_cyclic':
>> drivers/dma/sh/shdma-base.c:683:4: warning: format '%d' expects argument of
>> type 'int', but argument 4 has type 'size_t' [-Wformat=]
__func__, buf_len, period_len, slave_id);
>> drivers/dma/sh/shdma-base.c:683:4: warning: format '%d' expects argument of
>> type 'int', but argument 5 has type 'size_t' [-Wformat=]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
kbuild test robot reports that shdma_prep_dma_cyclic should be static, since
symbol is not declared, quick check revails that is the case
>> drivers/dma/sh/shdma-base.c:660:32: sparse: symbol 'shdma_prep_dma_cyclic'
>> was not declared. Should it be static?
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing lists),
we are here adding a drivers/soc directory. The purpose of this is
to keep per-vendor shared code that's needed by different drivers but
that doesn't fit into the MFD (nor drivers/platform) model. We expect
to keep merging contents for this hierarchy through arm-soc so we can
keep an eye on what the vendors keep adding here and not making it a
free-for-all to shove in crazy stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=SC+e
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC driver changes from Olof Johansson:
"SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing
lists), we are here adding a drivers/soc directory. The purpose of
this is to keep per-vendor shared code that's needed by different
drivers but that doesn't fit into the MFD (nor drivers/platform)
model. We expect to keep merging contents for this hierarchy through
arm-soc so we can keep an eye on what the vendors keep adding here and
not making it a free-for-all to shove in crazy stuff"
* tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
cpufreq: exynos: Fix driver compilation with ARCH_MULTIPLATFORM
tty: serial: msm: Remove direct access to GSBI
power: reset: keystone-reset: introduce keystone reset driver
Documentation: dt: add bindings for keystone pll control controller
Documentation: dt: add bindings for keystone reset driver
soc: qcom: fix of_device_id table
ARM: EXYNOS: Fix kernel panic when unplugging CPU1 on exynos
ARM: EXYNOS: Move the driver to drivers/cpuidle directory
ARM: EXYNOS: Cleanup all unneeded headers from cpuidle.c
ARM: EXYNOS: Pass the AFTR callback to the platform_data
ARM: EXYNOS: Move S5P_CHECK_SLEEP into pm.c
ARM: EXYNOS: Move the power sequence call in the cpu_pm notifier
ARM: EXYNOS: Move the AFTR state function into pm.c
ARM: EXYNOS: Encapsulate the AFTR code into a function
ARM: EXYNOS: Disable cpuidle for exynos5440
ARM: EXYNOS: Encapsulate boot vector code into a function for cpuidle
ARM: EXYNOS: Pass wakeup mask parameter to function for cpuidle
ARM: EXYNOS: Remove ifdef for scu_enable in pm
ARM: EXYNOS: Move scu_enable in the cpu_pm notifier
ARM: EXYNOS: Use the cpu_pm notifier for pm
...
The APBX-DMA block is also found on MX6Q/MX6DL chips.
Update the help text accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
linux/err.h isn't implicitly included by the current headers on all
platforms, resulting in compilation failures due to implicit
declarations of IS_ERR and PTR_ERR. Fix this by including linux/err.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
linux/err.h isn't implicitly included by the current headers on all
platforms, resulting in compilation failures due to implicit
declarations of IS_ERR and PTR_ERR. Fix this by including linux/err.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
linux/err.h isn't implicitly included by the current headers on all
platforms, resulting in compilation failures due to implicit
declarations of IS_ERR and PTR_ERR. Fix this by including linux/err.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Many audio interface drivers require support of cyclic transfers to work
correctly, for example Samsung ASoC DMA driver. This patch adds support
for cyclic transfers to the s3c24xx-dma driver
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Due to redundant 'break' in loop driver processed only first chunk.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In cyclic dma tx's handler sdma_handle_channel_loop(),
SDMA channel statue is set to either DMA_ERROR or DMA_IN_PROGRESS
based on each period's status. This has the following issues:
1) If one period's status is BD_RROR, then channel status
will be set to DMA_ERROR, but it will be overwritten to DMA_IN_PROGRESS
if the following periods are OK.
2) DMA client may call sdma_control(DMA_TERMINATE_ALL) to stop the cyclic dma
operation, sdma channel status will be set to DMA_ERROR,
but if after this handler is called, then again the channel status will be overwritten
to DMA_IN_PROGRESS. Then the following dmaengine_prep_dma_cyclic() will always fail,
as channel status is DMA_IN_PROGRESS.
As in cyclic dma tx, channel status will be initially set to DMA_IN_PROGRESS,
driver only needs to change it to DMA_ERROR, when something wrong happens
(one period status is wrong, or stoped by client explicitly).
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull slave-dmaengine fixes from Vinod Koul:
"We have three small fixes.
First one from Andy reverts the devm_request irq as we need to ensure
the tasklet is killed after irq is freed, so we need to do free irq in
our code. Other two from Arnd are fixing the compilation issue in
omap and sa11x0 drivers with ARM randconfigs"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: sa11x0: remove broken #ifdef
dmaengine: omap: hide filter_fn for built-in drivers
dmaengine: dw: went back to plain {request,free}_irq() calls
commit 4828b493 introduced COMPILE_TEST for this driver and this cause compile
failure on alpha as kzalloc wasnt availble for this arch in included header, so
explictly add slab.h
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_async_device_register() may return non-zero error code. In such case we
have to follow error path.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit dbde5c29 "dw_dmac: use devm_* functions to simplify code" turns
probe function to use devm_* helpers and simultaneously brings a regression.
We have to 1) call clk_disable_unprepare() on error path, and 2) check error
code of clk_enable_prepare(). First part was done in the original code, second
one is an update.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
hclk signal is a bus clock. So, it means we have to have it enabled during
access to the DMA controller. This patch makes sure that we enable clock before
access to the device, though it currently works on Intel hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pch_dma driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Introduce support for slave s/g transfer preparation and the associated
device control callback in the MPC512x DMA controller driver, which adds
support for data transfers between memory and peripheral I/O to the
previously supported mem-to-mem transfers.
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
[fixed subsytem name]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The count which is used to get_unmap_data maybe not the same as the
count computed in dmaengine_unmap which causes to free data in a
wrong pool.
This patch fixes this issue by keeping the map count with unmap_data
structure and use this count to get the pool.
Cc: <stable@vger.kernel.org>
Signed-off-by: Xuelin Shi <xuelin.shi@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We need to use writel() instead of writel_relaxed() when starting
a channel, to ensure all the descriptors have been flushed before
the activation.
While at it, remove the unneeded read-modify-write and make the
code simpler.
Cc: <stable@vger.kernel.org>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The sa11x0_dma_pm_ops unconditionally reference sa11x0_dma_resume
and sa11x0_dma_suspend, which currently breaks if CONFIG_PM_SLEEP
is disabled.
There is probably a better way to remove the reference in this
case, but the safe choice is to have the suspend/resume code always
built in the driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: dmaengine@vger.kernel.org
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is deprecated.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit dbde5c29 "dw_dmac: use devm_* functions to simplify code" turns
probe function to use devm_* helpers and simultaneously brings a regression. We
need to ensure irq is disabled, followed by ensuring that don't schedule any
more tasklets and then its safe to use tasklet_kill().
The free_irq() will ensure that the irq is disabled and also wait till all
scheduled interrupts are executed by invoking synchronize_irq(). So we need to
only do tasklet_kill() after invoking free_irq().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Clients may still be active in the early phase of system PM, thus we
need to move the suspend operations to the late system PM phase.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A channel can accommodate more than one transaction, each consisting of
multiple descriptors, the last of which has the DCMD_ENDIRQEN bit set.
In order to report the channel's residue, we hence have to walk the
list of running descriptors, look for those which match the cookie,
and then try to find the descriptor which defines upper and lower
boundaries that embrace the current transport pointer. Once it is found,
walk forward until we find the descriptor that tells us about the end of
a transaction via a set DCMD_ENDIRQEN bit.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Make sure to handle register context save/restore when needed from
system PM callbacks.
Previously we solely trusted the device to reside in in-active state
while the system suspend callback were invoked, which is just too
optimistic.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Converting to the PM macros makes us simplify and remove some code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
While probing, don't rely on CONFIG_PM_RUNTIME to be configured.
Instead, let's power up the device and make it fully operational.
Update the runtime PM status to reflect the active state.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The runtime PM resume callback needs to be executed while holding the
spinlock, make sure to maintain this for the pause operation as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit 4501fe61 "dma: dw: Add suspend and resume handling for PCI mode
DW_DMAC." introduces system power management callbacks. Regarding to commit
f78c4cff "PM / Sleep: Add macro to define common late/early system PM
callbacks" we have nice macro to setup dev_pm_ops structure. This patch
converts a driver to use the macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to use *_noirq version of suspend and resume PM callbacks. The
suspend_late / resume_early suit better (it was discussed in [1]) and in future
could be used for runtime PM support.
[1] http://www.spinics.net/lists/kernel/msg1650974.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix mpc_dma_probe() error path and mpc_dma_remove(): manually free IRQs and
dispose IRQ mappings before devm_* takes care of other resources.
Moreover replace devm_request_irq() with request_irq() since there is no need
to use it because the original code always frees IRQ manually with
devm_free_irq(). Replace devm_free_irq() with free_irq() accordingly.
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
MPC512x and MPC8308 have similar DMA controllers, but are independent SoCs.
DMA controller driver should have separate 'compatible' values for these SoCs.
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Concentrate the specific code for MPC8308 in the 'if' branch
and handle MPC512x in the 'else' branch.
This modification only reorders instructions but doesn't change behaviour.
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
These functions will be modified in the next patch in the series. By moving the
function in a patch separate from the changes, it will make review easier.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Qiang Liu <qiang.liu@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are several places where descriptors are freed using identical code.
This patch puts this code into a function to reduce code duplication.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Qiang Liu <qiang.liu@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Delete attribute DMA_INTERRUPT because fsldma doesn't support this function,
exception will be thrown if talitos is used to offload xor at the same time.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Qiang Liu <qiang.liu@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Methods of accessing DMA controller registers are inconsistent, some registers
are accessed by DMA_IN/OUT directly, while others are accessed by functions
get/set_* which are wrappers of DMA_IN/OUT, and even for the BCR register, it
is read by get_bcr but written by DMA_OUT.
This patch unifies the inconsistent methods, all registers are accessed by
get/set_* now.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some codes are calling chan_dbg with FSL_DMA_LD_DEBUG surrounded, it is really
unnecessary to use such a macro because chan_dbg is a wrapper of dev_dbg, we do
have corresponding DEBUG macro to switch on/off dev_dbg, and most of the other
codes are also calling chan_dbg directly without using FSL_DMA_LD_DEBUG.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add cyclic transfer support and enables dmaengine_prep_dma_cyclic()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[reflown changelog for readablity]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current shdma is using "last" which indicates last desc which needs to have
callback function. But that desc's chunks is always 1, we can use it as finder
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[reflown changelog for readablity]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use sizeof(*var) instead of sizeof(type) when calling devm_k*alloc().
This avoids using the wrong type as was done to allocate the physical
channels array.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As the physical channel and virtual channel point to each other,
pchan->phy->vchan is always equal to pchan. Simplify the code
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is the driver for the AXI Video Direct Memory Access (AXI
VDMA) core, which is a soft Xilinx IP core that provides high-
bandwidth direct memory access between memory and AXI4-Stream
type video target peripherals. The core provides efficient two
dimensional DMA operations with independent asynchronous read
and write channel operation.
This module works on Zynq (ARM Based SoC) and Microblaze platforms.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Reviewed-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
edma param struct is now within an edma_pset struct introduced in Thomas
Gleixner's edma tx status series. Update memcpy function for the same.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The granular residue accounting code uses certain variables specifically
for residue accounting. Document these in the structure declaration.
Also move around some elements and group them together.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The first slot in the ParamRAM of EDMA holds the current active
subtransfer. Depending on the direction we read either the source or
the destination address from there. In the internal psets we have the
address of the buffer(s).
In the cyclic case we only use the internal pset[0] which holds the
start address of the circular buffer and calculate the remaining room
to the end of the buffer.
In the SG case we read the current address and compare it to the
internal psets address and length.
- If the current address is outside of this range, the pset has been
processed already and we mark it done, update the residue_stat value
and process the next set. That avoids that we need to walk all
processed psets for every invocation of tx_status.
- If its inside the range we know that we look at the current active
set and stop the walk.
- In case of intermediate transfers we update the stats in the
interrupt callback function before starting the next batch of
transfers. The tx_status callback and the interrupt callback are
serialized via vchan.lock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[joelf@ti.com: Hunk #2 in original patch manually applied]
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
For granular accounting we need to store the direction and the
information for the individual psets:
- source or destination address, depending on direction
- length
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Preparatory patch to support finer grained accounting.
Move the edma_params array out of edma_desc so we can add further per
pset data to it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[joelf@ti.com: Fixed up hunk #3 in original patch to apply]
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It's likely that the caller investigates the status of a currently
active descriptor. Make that simple check first and only rumage in the
vchan list if that fails.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The residue reporting in edma_tx_status() is just broken. It blindly
walks the psets and recalculates the lenght of the transfer from the
hardware parameters. For cyclic transfers it adds the link pset, which
results in interestingly large residues. For non-cyclic it adds the
dummy pset, which is stupid as well.
Aside of that it's silly to walk through the pset params when the per
descriptor residue is known at the point of creating it.
Store the information in edma_desc and use it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It helps to identify issues if we have some information regarding to the
channel which the event is associated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The vchan lock in edma_callback is acquired in hard interrupt context. As
interrupts are already disabled, there's no point in save/restoring interrupt
mask bit or cpsr flags.
Get rid of flags local variable and use spin_lock instead of spin_lock_irqsave.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We add DMA memcpy support to EDMA driver. Successful tests performed using
dmatest kernel module. Copy alignment is set to DMA_SLAVE_BUSWIDTH_4_BYTES and
users must ensure length is aligned so that copy is performed fully.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case of not supported direction it is better to print the direction also.
It is unlikely, but in such an event it helps with the debugging.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-and-Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Ujfalusi