The default hop penalty is currently set to 15, which is applied like
that for multi interface devices (e.g. dual band APs). Single band
devices will still use an effective penalty of 30 (hop penalty + wifi
penalty).
After receiving reports of too long paths in mesh networks with dual
band APs which were fixed by increasing the hop penalty, we'd like to
suggest to increase that default value in the default setting as well.
We've evaluated that increase in a handful of medium sized mesh
networks (5-20 nodes) with single and dual band devices, with changes
for the better (shorter routes, higher throughput) or no change at all.
This patch changes the hop penalty to 30, which will give an effective
penalty of 60 on single band devices (hop penalty + wifi penalty).
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Conflicts:
drivers/infiniband/hw/cxgb4/device.c
The cxgb4 conflict was simply overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN interface (on top of batX) is removed and
re-added within a short timeframe TT does not have enough
time to properly cleanup. This creates an internal TT state
mismatch as the newly created softif_vlan will be
initialized from scratch with a TT client count of zero
(even if TT entries for this VLAN still exist). The
resulting TT messages are bogus due to the counter / tt
client listing mismatch, thus creating inconsistencies on
every node in the network
To fix this issue destroy_vlan() has to not free the VLAN
object immediately but it has to be kept alive until all the
TT entries for this VLAN have been removed. destroy_vlan()
still removes the sysfs folder so that the user has the
feeling that everything went fine.
If the same VLAN is re-added before the old object is free'd,
then the latter is resurrected and re-used.
Implement such behaviour by increasing the reference counter
of a softif_vlan object every time a new local TT entry for
such VLAN is created and remove the object from the list
only when all the TT entries have been destroyed.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch a node sends IPv4 multicast packets to nodes which
have a BATADV_MCAST_WANT_ALL_IPV4 flag set and IPv6 multicast packets
to nodes which have a BATADV_MCAST_WANT_ALL_IPV6 flag set, too.
Why is this needed? There are scenarios involving bridges where
multicast report snooping and multicast TT announcements are not
sufficient, which would lead to packet loss for some nodes otherwise:
MLDv1 and IGMPv1/IGMPv2 have a suppression mechanism
for multicast listener reports. When we have an MLDv1/IGMPv1/IGMPv2
querier behind a bridge then our snooping bridge is potentially not
going to see any reports even though listeners exist because according
to RFC4541 such reports are only forwarded to multicast routers:
-----------------------------------------------------------
---------------
{Querier}---|Snoop. Switch|----{Listener}
---------------
\ ^
-------
| br0 | < ???
-------
\
_-~---~_
_-~/ ~-_
~ batman-adv \-----{Sender}
\~_ cloud ~/
-~~__-__-~_/
I) MLDv1 Query: {Querier} -> flooded
II) MLDv1 Report: {Listener} -> {Querier}
-> br0 cannot detect the {Listener}
=> Packets from {Sender} need to be forwarded to all
detected listeners and MLDv1/IGMPv1/IGMPv2 queriers.
-----------------------------------------------------------
Note that we do not need to explicitly forward to MLDv2/IGMPv3 queriers,
because these protocols have no report suppression: A bridge has no
trouble detecting MLDv2/IGMPv3 listeners.
Even though we do not support bridges yet we need to provide the
according infrastructure already to not break compatibility later.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With this patch a node may additionally perform the dropping or
unicasting behaviour for a link-local IPv4 and link-local-all-nodes
IPv6 multicast packet, too.
The extra counter and BATADV_MCAST_WANT_ALL_UNSNOOPABLES flag is needed
because with a future bridge snooping support integration a node with a
bridge on top of its soft interface is not able to reliably detect its
multicast listeners for IPv4 link-local and the IPv6
link-local-all-nodes addresses anymore (see RFC4541, section 2.1.2.2
and section 3).
Even though this new flag does make "no difference" now, it'll ensure
a seamless integration of multicast bridge support without needing to
break compatibility later.
Also note, that even with multicast bridge support it won't be possible
to optimize 224.0.0.x and ff02::1 towards nodes with bridges, they will
always receive these ranges.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With this patch a multicast packet is not always simply flooded anymore,
the behaviour for the following cases is changed to reduce
unnecessary overhead:
If all nodes within the horizon of a certain node have signalized
multicast listener announcement capability then an IPv6 multicast packet
with a destination of IPv6 link-local scope (excluding ff02::1) coming
from the upstream of this node...
* ...is dropped if there is no according multicast listener in the
translation table,
* ...is forwarded via unicast if there is a single node with interested
multicast listeners
* ...and otherwise still gets flooded.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
If the soft interface of a node is not part of a bridge then a node
announces a new multicast TVLV: The existence of this TVLV
signalizes that this node is announcing all of its multicast listeners
via the translation table infrastructure.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
On some architectures ether_addr_copy() is slightly faster
than memcpy() therefore use the former when possible.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Our .ndo_start_xmit handler (batadv_interface_tx()) can rely on having
the skb mac header pointer set correctly since the following commit
present in kernels >= 3.9:
"net: reset mac header in dev_start_xmit()" (6d1ccff627)
Therefore we can safely use eth_hdr() and vlan_eth_hdr() instead of
skb->data now, which spares us some ugly type casts.
At the same time set the mac_header in batadv_dat_snoop_incoming_arp_request()
before sending the skb along the TX path.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
If the same interface is used for sending and receiving, there might be
throughput degradation on half-duplex interfaces such as WiFi. Add a
penalty if the same interface is used to reflect this problem in the
metric. At the same time, change the hop penalty from 30 to 15 so there
will be no change for single wifi mesh network. the effective hop
penalty will stay at 30 due to the new wifi penalty for these networks.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
If a broadcast packet is coming from a client marked as
isolated, then mark the skb using the isolation mark so
that netfilter (or any other application) can recognise
them.
The mark is written in the skb based on the mask value:
only bits set in the mask are substitued by those in the
mark value
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
A client sending packets which mark matches the value
configured via sysfs has to be identified as isolated using
the TT_CLIENT_ISOLA flag.
The match is mask based, meaning that only bits set in the
mask are compared with those in the mark value.
If the configured mask is equal to 0 no operation is
performed.
Such flag is then advertised within the classic client
announcement mechanism.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This attribute can be used to set and read the value and the
mask of the skb mark which will be used to classify the
source non-mesh client as ISOLATED. In this way a client can
be advertised as such and the mark can potentially be
restored at the receiving node before delivering the skb.
This can be helpful for creating network wide netfilter
policies.
This sysfs file expects a string of the shape "$mark/$mask".
Where $mark has to be a 32-bit number in any base, while
$mask must be a 32bit mask expressed in hex base. Only bits
in $mark covered by the bitmask are really stored.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
In different situations it is possible that the DHCP server
or client uses broadcast Ethernet frames to send messages
to each other. The GW component in batman-adv takes care of
using bat-unicast packets to bring broadcast DHCP
Discover/Requests to the "best" server.
On the way back the DHCP server usually sends unicasts,
but upon client request it may decide to use broadcasts as
well.
This patch improves the GW component so that it now snoops
and sends as unicast all the DHCP packets, no matter if they
were generated by a DHCP server or client.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
As suggested by checkpatch, remove all the references to the
FSF address since the kernel already has one reference in
its documentation.
In this way it is easier to update it in case of future
changes.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
When batadv_get_vid() is invoked in interface_rx() the
batman-adv header has already been removed, therefore
the header_len argument has to be 0.
Introduced by c018ad3de6
("batman-adv: add the VLAN ID attribute to the TT entry")
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
If an interface enslaved into batman-adv is a bridge (or a
virtual interface built on top of a bridge) the nf_bridge
member of the skbs reaching the soft-interface is filled
with the state about "netfilter bridge" operations.
Then, if one of such skbs is locally delivered, the nf_bridge
member should be cleaned up to avoid that the old state
could mess up with other "netfilter bridge" operations when
entering a second bridge.
This is needed because batman-adv is an encapsulation
protocol.
However at the moment skb->nf_bridge is not released at all
leading to bogus "netfilter bridge" behaviours.
Fix this by cleaning the netfilter state of the skb before
it gets delivered to the upper layer in interface_rx().
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The size of the batadv_header of 3 is problematic on some architectures
which automatically pad all structures to a 32 bit boundary. To not lose
performance by packing this struct, better embed it into the various
host structures.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The local translation table size is limited by what can be
transferred from one node to another via a full table request.
The number of entries fitting into a full table request depend
on whether the fragmentation is enabled or not. Therefore this
patch introduces a max table size check and refuses to add
more local clients when that size is reached. Moreover, if the
max full table packet size changes (MTU change or fragmentation
is disabled) the local table is downsized instantaneously.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
With this patch the functions batadv_send_skb_unicast() and
batadv_send_skb_unicast_4addr() are further refined into
batadv_send_skb_via_tt(), batadv_send_skb_via_tt_4addr() and
batadv_send_skb_via_gw(). This way we avoid any "guessing" about where to send
a packet in the unicast forwarding methods and let the callers decide.
This is going to be useful for the upcoming multicast related patches in
particular.
Further, the return values were polished a little to use the more
appropriate NET_XMIT_* defines.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
AP isolation has to be enabled on one VLAN interface only.
This patch moves the AP isolation attribute to the per-vlan
interface attribute set, enabling it to have a different
value depending on the selected vlan.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Each VLAN can now have its own set of attributes which are
exported through a new subfolder in the sysfs tree.
Each VLAN created on top of a soft_iface will have its own
subfolder.
The subfolder is named "vlan%VID" and it is created inside
the "mesh" sysfs folder belonging to batman-adv.
Attributes corresponding to the untagged LAN are stored in
the root sysfs folder as before.
This patch also creates all the needed macros and data
structures to easily handle new VLAN spacific attributes.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Since batman-adv is now fully VLAN-aware, a proper framework
able to handle per-vlan-interface attributes is needed.
Those attributes will affect the associated VLAN interface
only, rather than the real soft_iface (which would result
in every vlan interface having the same attribute
configuration).
To make the code simpler and easier to extend, attributes
associated to the standalone soft_iface are now treated
like belonging to yet another vlan having a special vid.
This vid is different from the others because it is made up
by all zeros and the VLAN_HAS_TAG bit is not set.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
To make the translation table code VLAN-aware, each entry
must carry the VLAN ID which it belongs to. This patch adds
such attribute to the related TT structures.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
We do not actually need to set any rx filters for the virtual batman
soft interface. However a dummy handler enables a user to set static
multicast listeners for instance.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The module prints a warning when the MTU on the hard interface is too
small to transfer payload traffic without fragmentation. The required
MTU is calculated based on the encapsulation header size. If network
coding is compild into the module its header size is taken into
account as well.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
When comparing a network ordered value with a constant, it
is better to convert the constant at compile time by means
of htons() instead of converting the value at runtime using
ntohs().
This refactoring may slightly improve the code performance.
Moreover substitute __constant_htons() with htons() since
the latter increase readability and it is smart enough to be
as efficient as the former
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Non-broadcast packets larger than MTU are fragmented and sent with
an encapsulating header. Up to 16 fragments are supported, which are
sent in reverse order on the wire to allow minimal memory copying when
creating fragments.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Fragments arriving at their destination are buffered for later merge.
Merged packets are passed to the main receive function as had they never
been fragmented.
Fragments are forwarded without merging if the MTU of the outgoing
interface is smaller than the size of the merged packet.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Remove the existing fragmentation code before adding the new version
and delete unicast.{h,c}.
batadv_unicast_send_skb() is moved to send.c and renamed to
batadv_send_skb_unicast().
fragmentation entry in sysfs (bat_priv->fragmentation) is kept for use in
the new fragmentation code.
BATADV_UNICAST_FRAG packet type is renamed to BATADV_FRAG for use in the
new fragmentation code.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
This is replaced by a userspace program, we don't need this
functionality to bloat the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Prior to this patch batman-adv read the advertised uplink bandwidth
from userspace and compressed this information into a single byte
called "gateway class".
Now the download & upload bandwidth information is sent as-is. No
userspace change is necessary since the sysfs API always allowed
to specify a bandwidth.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Spyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
When receiving or sending a packet a packet on a VLAN, the
vid has to be marked with the TAG flag in order to make any
component in batman-adv understand that the packet is coming
from a really tagged network.
This fix the Bridge Loop Avoidance behaviour which was not
able to send announces over VLAN interfaces.
Introduced by 0b1da1765fdb00ca5d53bc95c9abc70dfc9aae5b
("batman-adv: change VID semantic in the BLA code")
Signed-off-by: Antonio Quartulli <antonio@open-mesh.org>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The skb priority field may help the wireless driver to choose the right
queue (e.g. WMM queues). This should be set in batman-adv, as this
information is only available here.
This patch adds support for IPv4/IPv6 DS fields and VLAN PCP. Note that
only VLAN PCP is used if a VLAN header is present. Also initially set
TC_PRIO_CONTROL only for self-generated packets, and keep the priority
set by higher layers.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
There are several functions which might reallocate skb data. Currently
some places keep reusing their old ethhdr pointer regardless of whether
they became invalid after such a reallocation or not. This potentially
leads to kernel paging errors.
This patch fixes these by refetching the ethdr pointer after the
potential reallocations.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In order to make batman-adv fully vlan aware later, the
semantic used for variables storing the VLAN ID values has
to be changed in order to be adapted to the new one which
will be used batman-adv wide.
In particular, the VID has to be an "_unsigned_ short int"
and its 4 MSB will be used as a flag bitfield, while the
remaining 12 bits are used to store the real VID value
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Instead of casting the result of skb_mac_header() to
"struct ethhdr *" every time, the eth_hdr inline function
can be use to beautify the code and improve its readability.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
On errors in batadv_mesh_init(), bat_counters will be freed in both
batadv_mesh_free() and batadv_softif_init_late(). This patch fixes this
by returning earlier from batadv_softif_init_late() in case of errors in
batadv_mesh_init() and by setting bat_counters to NULL after freeing.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
batadv_mesh_free() schedules some RCU callbacks which need the bat_priv struct
to do their jobs, while free_netdev(), which is called immediately after, is
destroying the private data.
Put an rcu_barrier() in the middle so that free_netdev() is invoked only after
all the callbacks returned.
This bug has been introduced by ab8f433dd39be94e8617cff2dfe9f7eca162eb15
("batman-adv: Move deinitialization of soft-interface to destructor")
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sysfs configuration interface of batman-adv to add/remove slaves of an
soft-iface is not deadlock free and doesn't follow the currently common way to
modify slaves of an interface.
An additional configuration interface though rtnl_link is introduced which
provides easy device adding/removing with tools like "ip":
$ ip link set dev eth0 master bat0
$ ip link set dev eth0 nomaster
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The sysfs configuration interface of batman-adv to add/remove soft-interfaces
is not deadlock free and doesn't follow the currently common way to create new
virtual interfaces.
An additional interface though rtnl_link is introduced which provides easy device
creation/deletion with tools like "ip":
$ ip link add dev bat0 type batadv
$ ip link del dev bat0
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
CC: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The deinitialization of the soft-interface created in ndo_init/constructor
should be done in the destructor and not directly before calling
unregister_netdevice
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The initialization of an net_device object should be done in the
init/constructor function and not from the outside after the register_netdevice
was done to avoid race conditions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When receiving a network coded packet, the decoding buffer is searched
for a packet to use for decoding. The source, destination, and crc32 from
the coded packet is used to identify the wanted packet. The decoded
packet is passed to the usual unicast receiver function, as had it never
been network coded.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
To be able to decode a network coded packet, a node must already know
one of the two coded packets. This is done by buffering skbs before
transmission and buffering packets sniffed with promiscuous mode from
other hosts.
Packets are kept in a buffer similar to the one with forward-skbs: A
hash table, where each entry, which corresponds to a src-dst pair, has a
linked list packets.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Before adding forward-skbs to the coding buffer, the buffer is searched
for a potential coding opportunity. If one is found, the two packets are
network coded and transmitted right away. If not, the forward-skb is
added to the buffer.
Network coded packets are transmitted with information about the two
receivers and the two coded packets. The first receiver is given by the
MAC header, while the second is given in the payload/bat-header. The
second receiver uses promiscuous mode to receive the packet and check
the second destination.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Network coding exploits the 802.11 shared medium to allow multiple
packets to be sent in a single transmission. In brief, a relay can XOR
two packets, and send the coded packet to two destinations. The
receivers can decode one of the original packets by XOR'ing the coded
packet with the other original packet. This will lead to increased
throughput in topologies where two packets cross one relay.
In a simple topology with three nodes, it takes four transmissions
without network coding to get one packet from Node A to Node B and one
from Node B to Node A:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <--- p2 ---- Node R Node B
4. Node A Node R ---- p1 ---> Node B
With network coding, the relay only needs one transmission, which saves
us one slot of valuable airtime:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <- p1 x p2 - Node R - p1 x p2 -> Node B
The same principle holds for a topology including five nodes. Here the
packets from Node A and Node B are overheard by Node C and Node D,
respectively. This allows Node R to send a network coded packet to save
one transmission:
Node A Node B
| \ / |
| p1 p2 |
| \ / |
p1 > Node R < p2
| |
| / \ |
| p1 x p2 p1 x p2 |
v / \ v
/ \
Node C < > Node D
More information is available on the open-mesh.org wiki[1].
This patch adds the initial code to support network coding in
batman-adv. It sets up a worker thread to do house keeping and adds a
sysfs file to enable/disable network coding. The feature is disabled by
default, as it requires a wifi-driver with working promiscuous mode, and
also because it adds a small delay at each hop.
[1] http://www.open-mesh.org/projects/batman-adv/wiki/Catwoman
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When processing the unregister notify for a hard interface, removing
the sysfs files may lead to a circular deadlock (rtnl mutex <->
s_active).
To overcome this problem, postpone the sysfs removal in a worker.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When the Bridge Loop Avoidance component is not compiled-in, its boolean switch
should be not compiled as well. This patch surrounds the switch with a proper
ifdef.
This behaviour was introduced by 9fd6b0615b5499b270d39a92b8790e206cf75833
("batman-adv: add bridge loop avoidance compile option")
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The current translation table mechanism is not suitable for multicast
addresses and we are currently flooding such frames anyway.
Therefore this patch prevents multicast MAC addresses being added to the
translation table.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ETH_P_BATMAN ethertype is now defined kernel-wide. Use it instead
of the private BATADV_ETH_P_BATMAN define.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The logic in the BLA mechanism may decide to drop broadcast packets
because the node may still be in the setup phase. For this reason,
further broadcast processing like the early client detection mechanism
must be done only after the BLA check.
This patches moves the invocation to BLA before any other broadcast
processing.
This was introduced 30cfd02b60
("batman-adv: detect not yet announced clients")
Reported-by: Glen Page <glen.page@thet.net>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
tt_poss_change is a node-wide flag which tells whether the node is in a roaming
state (a client recently moved to/away from it) in order to let it apply special
re-routing rules. However this flag does not give a clear idea of the current
state because it is not possible to understand *which client* is actually
involved in the roaming. For this reason a better approach has been chosen:
instead of using a node-wide variable, the roaming state is now given by a
per-tt_entry ROAM flag which, in case of packet coming through the node, tells
the node whether the real destination is in roaming state or not.
With this flag change, batadv_check_unicast_ttvn() has also been rearranged in
order to better fit the new re-routing logic and to be much more readable.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This patch adds a runtime switch that enables the user to turn the DAT feature
on or off at runtime
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In case of an ARP message going in or out the soft_iface, it is intercepted and
a special action is performed. In particular the DHT helper functions previously
implemented are used to store all the ARP entries belonging to the network in
order to provide a fast and unicast lookup instead of the classic broadcast
flooding mechanism.
Each node stores the entries it is responsible for (following the DHT rules) in
its soft_iface ARP table. This makes it possible to reuse the kernel data
structures and functions for ARP management.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The current unicast packet type does not contain the orig source address. This
patches add a new unicast packet (called UNICAST_4ADDR) which provides two new
fields: the originator source address and the subtype (the type of the data
contained in the packet payload). The former is useful to identify the node
which injected the packet into the network and the latter is useful to avoid
creating new unicast packet types in the future: a macro defining a new subtype
will be enough.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
We have seen this to break networks when used with bridge loop
avoidance. As we can't see any benefit from sending these ancient frames
via our mesh, we just drop them.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Transmissions over batman-adv devices always start another nested transmission
over devices attached to the batman-adv interface. These devices usually use
the ethernet lockdep class for the tx_queue lock which is also set by default
for all batman-adv devices. Lockdep will detect a nested locking attempt of two
locks with the same class and warn about a possible deadlock.
This is the default and expected behavior and should not alarm the locking
correctness prove mechanism. Therefore, the locks for all netdevice specific tx
queues get a special batman-adv lock class to avoid a false positive for each
transmission.
Reported-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
Into function interface_set_mac_addr, the function tt_local_add was
invoked before updating dev->dev_addr. The new MAC address was not
tagged as NoPurge.
Signed-off-by: Def <def@laposte.net>
In order to understand where a broadcast packet is coming from and use
this information to detect not yet announced clients, this patch modifies the
interface_rx() function by passing a new argument: the orig node
corresponding to the node that originated the received packet (if known).
This new argument if not NULL for broadcast packets only (other packets does not
have source field).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The structure batadv_priv grows everytime a new feature is introduced. It gets
hard to find the parts of the struct that belongs to a specific feature. This
becomes even harder by the fact that not every feature uses a prefix in the
member name.
The variables for bridge loop avoidence, gateway handling, translation table
and visualization server are moved into separate structs that are included in
the bat_priv main struct.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the gateway functionality is used, some broadcast packets (DHCP
requests) may be transmitted as unicast packets. As the bridge loop
avoidance code now only considers the payload Ethernet destination,
it may drop the DHCP request for clients which are claimed by other
backbone gateways, because it falsely infers from the broadcast address
that the right backbone gateway should havehandled the broadcast.
Fix this by checking and delegating the batman-adv packet type used
for transmission.
Reported-by: Guido Iribarren <guidoiribarren@buenosaireslibre.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
The reserved fields in batman-adv packets are not set to a constant value. The
content of these memory regions is leaked unintentionally to the network.
This regression was introduced in 3b27ffb00f
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The "bat_" prefix in the source files implementing the batman-adv sysfs and
debugfs interface doesn't have a special meaning and are only used by these
files and files that implement the actual B.A.T.M.A.N. path finding algorithm.
The prefix is better suited to mark files that are used to implement the main
part of the path finding. All other files should not use it and therefore gets
renamed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv doesn't follow the style for multiline comments that David S. Miller
prefers. All comments should be reformatted to follow this consistent style to
make the code slightly more readable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Added additional counters in a bat_stats structure, which are exported
through the ethtool api. The counters are specific to batman-adv and
includes:
forwarded packets and bytes
management packets and bytes (aggregated OGMs at this point)
translation table packets
New counters are added by extending "enum bat_counters" in types.h and
adding corresponding descriptive string(s) to bat_counters_strings in
soft-iface.c.
Counters are increased by calling batadv_add_counter() and incremented
by one by calling batadv_inc_counter().
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Instead of using sizeof(struct ethhdr) it is strongly recommended to use the
kernel macro ETH_HLEN. This patch substitute each occurrence of the former
expressione with the latter one.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The define CONFIG_BATMAN_ADV_BLA switches the bridge loop avoidance
on - skip it, and the bridge loop avoidance is not compiled in.
This is useful if binary size should be saved or the feature is
not needed.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This second version of the bridge loop avoidance for batman-adv
avoids loops between the mesh and a backbone (usually a LAN).
By connecting multiple batman-adv mesh nodes to the same ethernet
segment a loop can be created when the soft-interface is bridged
into that ethernet segment. A simple visualization of the loop
involving the most common case - a LAN as ethernet segment:
node1 <-- LAN --> node2
| |
wifi <-- mesh --> wifi
Packets from the LAN (e.g. ARP broadcasts) will circle forever from
node1 or node2 over the mesh back into the LAN.
With this patch, batman recognizes backbone gateways, nodes which are
part of the mesh and backbone/LAN at the same time. Each backbone
gateway "claims" clients from within the mesh to handle them
exclusively. By restricting that only responsible backbone gateways
may handle their claimed clients traffic, loops are effectively
avoided.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The functionality is to be replaced by an improved implementation,
so first clean up.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Remove dev_addr in interface_setup(), it's not needed anymore.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: use bitops, adapt to eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To increase readability the has_timed_out() functions has been introduced.
This patch converts existing time_after() calls to use this wrapper
function (if applicable).
This patch also converts all timeouts to miliseconds to be consistent.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
All batman-adv packets have a common 3 byte header. It can be used to share
some code between different code paths, but it was never explicit stated that
this header has to be always the same for all packets. Therefore, new code
changes always have the problem that they may accidently introduce regressions
by moving some elements around.
A new structure is introduced that contains the common header and makes it
easier visible that these 3 bytes have to be the same for all on-wire packets.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When entering softif_create(), the rtnl lock has already been acquired
by store_mesh_iface().
(store_mesh_iface() -> hardif_enable_interface() -> softif_create)
In case of an error, we should therefore call unregister_netdevice()
instead of unregister_netdev().
unregister_netdev() tries to acquire the rtnl lock itself and deadlocks
in this situation. unregister_netdevice() assumes that the rtnl lock
is already been held.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
corrects a critical bug of the GW feature. This bug made all the unicast
packets destined to a GW to be sent as broadcast. This bug is present even if
the sender GW feature is configured as OFF. It's an urgent bug fix and should
be committed as soon as possible.
This was a regression introduced by 43676ab590
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The follow-up routing code changes are going to introduce additional
routing packet types which make this distinction necessary.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
If a node has to send a packet issued by a WIFI client to another WIFI client,
the packet is dropped.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When a node receives a unicast packet it checks if the source and the
destination client can communicate or not due to the AP isolation
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Clients connected through a 802.11 device are now marked with the
TT_CLIENT_WIFI flag. This flag is also advertised with the tt
announcement.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Several typos have been corrected and some sentences have been rephrased
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Almost all of these have long outstayed their welcome.
And for every one of these macros, there are 10 features for which we
didn't add macros.
Let's just delete them all, and get out of habit of doing things this
way.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
In order to make possible to use the broadcast list for delayed sendings
the "delay" parameter is now provided instead of using 1 as hardcoded
value.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
If a client issues a DHCPREQUEST for renewal, the packet is dropped
if the old destination (the old gateway for the client) TQ is smaller
than the current best gateway TQ less GW_THRESHOLD
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
With the current client announcement implementation, in case of roaming,
an update is triggered on the new AP serving the client. At that point
the new information is spread around by means of the OGM broadcasting
mechanism. Until this operations is not executed, no node is able to
correctly route traffic towards the client. This obviously causes packet
drops and introduces a delay in the time needed by the client to recover
its connections.
A new packet type called ROAMING_ADVERTISEMENT is added to account this
issue.
This message is sent in case of roaming from the new AP serving the
client to the old one and will contain the client MAC address. In this
way an out-of-OGM update is immediately committed, so that the old node
can update its global translation table. Traffic reaching this node will
then be redirected to the correct destination utilising the fresher
information. Thus reducing the packet drops and the connection recovery
delay.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The client announcement mechanism informs every mesh node in the network
of any connected non-mesh client, in order to find the path towards that
client from any given point in the mesh.
The old implementation was based on the simple idea of appending a data
buffer to each OGM containing all the client MAC addresses the node is
serving. All other nodes can populate their global translation tables
(table which links client MAC addresses to node addresses) using this
MAC address buffer and linking it to the node's address contained in the
OGM. A node that wants to contact a client has to lookup the node the
client is connected to and its address in the global translation table.
It is easy to understand that this implementation suffers from several
issues:
- big overhead (each and every OGM contains the entire list of
connected clients)
- high latencies for client route updates due to long OGM trip time and
OGM losses
The new implementation addresses these issues by appending client
changes (new client joined or a client left) to the OGM instead of
filling it with all the client addresses each time. In this way nodes
can modify their global tables by means of "updates", thus reducing the
overhead within the OGMs.
To keep the entire network in sync each node maintains a translation
table version number (ttvn) and a translation table checksum. These
values are spread with the OGM to allow all the network participants to
determine whether or not they need to update their translation table
information.
When a translation table lookup is performed in order to send a packet
to a client attached to another node, the destination's ttvn is added to
the payload packet. Forwarding nodes can compare the packet's ttvn with
their destination's ttvn (this node could have a fresher information
than the source) and re-route the packet if necessary. This greatly
reduces the packet loss of clients roaming from one AP to the next.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
char was used in different places to store information without really
using the characteristics of that data type or by ignoring the fact that
char has not a well defined signedness.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
interface_tx is not used outside of soft-interface.c and thus doesn't
need to be declared inside soft-interface.h
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Usually rcu_dereference isn't necessary in situations were the
RCU-protected data structure cannot change, but sparse and lockdep still
need a similar functionality for analysis. rcu_dereference_protected
implements the reduced version which should be used to support the
dynamic and static analysis.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Documentation/CodingStyle recommends to use the form
p = kmalloc(sizeof(*p), ...);
to calculate the size of a struct and not the version where the struct
name is spelled out to prevent bugs when the type of p changes. This
also seems appropriate for manipulation of buffers when they are
directly associated with p.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv uses pointers which are marked as const and should not
violate that type qualifier by passing it to functions which force a
cast to the non-const version.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
It is slightly irritating that comments after a long line span over
multiple lines without any code. It is easier to put them before the
actual code and reduce the number of lines which the eye has to read.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
To be coherent, all the functions/variables/constants have been renamed
to the TranslationTable style
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
hardif_list_lock is unneccessary because we already ensure that no
multiple admin operations can take place through rtnl_lock.
hardif_list_lock only adds additional overhead and complexity.
Critical functions now check whether they are called with rtnl_lock
using ASSERT_RTNL.
It indirectly fixes the problem that orig_hash_del_if() expects that
only one interface is deleted from hardif_list at a time, but
hardif_remove_interfaces() removes all at once and then calls
orig_hash_del_if().
Reported-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The bridge loop detection for batman-adv allows the bat0 interface
to be bridged into an ethernet segment which other batman-adv nodes
are connected to. In order to also allow multiple VLANs on top of
the bat0 interface to be bridged into the ethernet segment this
patch extends the aforementioned bridge loop detection.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The RCU callback softif_neigh_free_rcu() just calls kfree(), so we can
use kfree_rcu() instead of call_rcu().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Marek Lindner <lindner_marek@yahoo.de>
Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
The rcu protected macros rcu_dereference() and rcu_assign_pointer()
for the bat_priv->primary_if need to be used, as well as spin/rcu locking.
Otherwise we might end up using a primary_if pointer pointing to already
freed memory.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antonio Quartulli