Recent Chelsio firmware started using few port capablity bits to
manage FEC and as driver was not aware of FEC changes those bits
were zeroed, consequently disabling FEC.
Avoid zeroing those bits and default to whatever the firmware
tells us the Link is currently advertising.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are using the smallest padding boundary (8 bytes), which isn't
smaller than the Memory Controller Read/Write Size
We get best performance in 100G when the Packing Boundary is a multiple
of the Maximum Payload Size. Its related to inefficient chopping of DMA
packets by PCIe, that causes more overhead on bus. So driver is helping
by making the starting address alignment to be MPS size.
We will try to determine PCIE MaxPayloadSize capabiltiy and set
IngPackBoundary based on this value. If cache line size is greater than
MPS or determinig MPS fails, we will use cache line size to determine
IngPackBoundary(as before).
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform an emergency shutdown of the adapter and stop it from
continuing any further communication on the ports or DMA to the
host. This is typically used when the adapter and/or firmware
have crashed and we want to prevent any further accidental
communication with the rest of the world. This will also force
the port Link Status to go down -- if register writes work --
which should help our peers figure out that we're down.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not count pause frames as part of general TX/RX frame
counters.
Based on the original work of Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port description for 25G and 100G cards, and also
change few port descriptions in compliance with the new
naming convention.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue comes when there are multiple threads attempting to use
the mailbox facility at the same time.
When DCB operations and interface up/down is run in a loop for every
0.1 sec, we observed mailbox collisions. And out of the two commands
one would fail with the present code, since we don't queue the second
command.
To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at
the head issue the mailbox command, else wait for the existing command
to complete. Usually command takes less than a milli-second to
complete.
Also timeout from the loop, if the command under execution takes
long time to run.
In reality, the number of mailbox access collisions is going to be
very rare since no one runs such abusive script.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t6fw-1.15.15.0 enabled compressed error vector in cpl_rx_pkt for T6.
Updating driver to take care of these changes.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added missing dev_port assignment in cxgb4vf driver.
Also made dev_port assignment of cxgb4 in sync with cxgb4vf driver.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing check for 25G and 100G while checking port speed,
which lead to less number of queues getting allocated for 25G & 100G
adapters and leading to low throughput. Adding the missing check for
both NIC and vNIC driver.
Also fixes port advertisement for 25G and 100G in ethtool output.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for ndo_get_vf_config, also fill the default mac address
that will be provided to the VF by firmware, in case user doesn't
provide one. So user can get the default MAC address address also
through ndo_get_vf_config.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to create tx traffic scheduling classes with specified
scheduling parameters. Return an existing class if a match is found
with same scheduling parameters.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_set_vf_mac support which allows to set the MAC address
for cxgb4vf interfaces from the host
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for firmware errors in the mailbox command loop and report
them differently rather than simply timing out when the firmware goes
belly up.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link goes down, from the interrupt handler DCB priority for the
Tx queues needs to be unset. We issue mbox command to unset the Tx queue
priority with negative timeout. In t4_wr_mbox_meat_timeout() do not sleep
when negative timeout is passed, since it is called from interrupt context.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new /sys/kernel/debug/ support to dump a firmware mailbox command
issued and replies for debugging purpose.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware can send a set of asynchronous replies through FW_PORT_CMD
with DCBX information when that's negotiated with the Link Peer. The old
code always assumed that a FW_PORT_CMD reply was always a Get Port
Information message. This change conditionalizes the code to only handle
the Get Port Information messages and throws a warning if we don't
understand what we've been given.
Also refactor t4_handle_fw_rpl() so that core functionality performed by
t4_handle_get_port_info() for a specified port.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor t4_port_init() so that the core functionality is done by
t4_init_portinfo() for a particular port. Also rename variables to
sensible ones.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new routine to print out general adapter information (various version
numbers, adapter name, part number, serial number, etc.) and remove
redundant information dumped in the Port Information.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix memory leak in iwlwifi, from Matti Gottlieb.
2) Add missing registration of netfilter arp_tables into initial
namespace, from Florian Westphal.
3) Fix potential NULL deref in DecNET routing code.
4) Restrict NETLINK_URELEASE to truly bound sockets only, from Dmitry
Ivanov.
5) Fix dst ref counting in VRF, from David Ahern.
6) Fix TSO segmenting limits in i40e driver, from Alexander Duyck.
7) Fix heap leak in PACKET_DIAG_MCLIST, from Mathias Krause.
8) Ravalidate IPV6 datagram socket cached routes properly, particularly
with UDP, from Martin KaFai Lau.
9) Fix endian bug in RDS dp_ack_seq handling, from Qing Huang.
10) Fix stats typing in bcmgenet driver, from Eric Dumazet.
11) Openvswitch needs to orphan SKBs before ipv6 fragmentation handing,
from Joe Stringer.
12) SPI device reference leak in spi_ks8895 PHY driver, from Mark Brown.
13) atl2 doesn't actually support scatter-gather, so don't advertise the
feature. From Ben Hucthings.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
openvswitch: use flow protocol when recalculating ipv6 checksums
Driver: Vmxnet3: set CHECKSUM_UNNECESSARY for IPv6 packets
atl2: Disable unimplemented scatter/gather feature
net/mlx4_en: Split SW RX dropped counter per RX ring
net/mlx4_core: Don't allow to VF change global pause settings
net/mlx4_core: Avoid repeated calls to pci enable/disable
net/mlx4_core: Implement pci_resume callback
net: phy: spi_ks8895: Don't leak references to SPI devices
net: ethernet: davinci_emac: Fix platform_data overwrite
net: ethernet: davinci_emac: Fix Unbalanced pm_runtime_enable
qede: Fix single MTU sized packet from firmware GRO flow
qede: Fix setting Skb network header
qede: Fix various memory allocation error flows for fastpath
tcp: Merge tx_flags and tskey in tcp_shifted_skb
tcp: Merge tx_flags and tskey in tcp_collapse_retrans
drivers: net: cpsw: fix wrong regs access in cpsw_ndo_open
tcp: Fix SOF_TIMESTAMPING_TX_ACK when handling dup acks
openvswitch: Orphan skbs before IPv6 defrag
Revert "Prevent NUll pointer dereference with two PHYs on cpsw"
VSOCK: Only check error on skb_recv_datagram when skb is NULL
...
Chelsio adapters have two VPD structures stored in the VPD:
- offset 0x000: an abbreviated VPD, and
- offset 0x400: the complete VPD.
After 104daa71b3 ("PCI: Determine actual VPD size on first access"), the
PCI core computes the valid VPD size by parsing the VPD starting at offset
0x0. That size only includes the abbreviated VPD structure, so reads of
the complete VPD at 0x400 fail.
Explicitly set the VPD size with pci_set_vpd_size() so the driver can read
both VPD structures.
[bhelgaas: changelog, split patches, rename to pci_set_vpd_size() and
return int (not ssize_t)]
Fixes: 104daa71b3 ("PCI: Determine actual VPD size on first access")
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Stop all Ethernet RX Queues before freeing up various Ingress/Egress
Queues, etc. We were seeing cases of Ingress Queues not getting serviced
during the shutdown process leading to Ingress Paths jamming up through
the chip and blocking the shutdown effort itself.
One such case involved the Firmware sending a "Flush Token" through the
ULP-TX -> ULP-RX path for an Ethernet TX Queue being freed in order to
make sure there weren't any remaining TX Work Requests in the pipeline.
But the return path was stalled by Ingress Data unable to be delivered to
the Host because those Ingress Queues were no longer being serviced.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SGE context congestion map changed from 4 to 8 priority per port
in T6 as there are only 2 channels.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating Congestion Channel/Priority Map in Congestion Manager Context
for T6. In T6 port 0 is mapped to channel 0 and port 1 is mapped to
channel 1. For 2 port T4/T5 adapter, port 0 is mapped to channel 0,1 and
port 1 is mapped to channel 2,3
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ingress padding boundary values got changed for T6.
T5: 0=32B 1=64B 2=128B 3=256B 4=512B 5=1024B 6=2048B 7=4096B
T6: 0=8B 1=16B 2=32B 3=64B 4=128B 5=128B 6=256B 7=512B
Updating the driver to set the correct boundary values in SGE_CONTROL to
32B.
Also, need to take care of this fl alignment change when calculating the
next packet offset.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated pm_stats code to display input FIFO wait (index 5) and read
latency (index 7) counters for T6 adapters
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t4_check_fw_version() can return several error codes (-EINVAL, -EBUSY,
-EAGAIN). The present code sets the adapter state to UNINIT only if its
an EFAULT. In all the error cases set the adapter to uninitialized state.
In t4_check_fw_version() if call to t4_get_fw_version() fails, repeat the
operation a few times before returning failure.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update T4/T5/T6 adapter register ranges so that it doesn't read non
existent registers when dumped using ethtool
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcing uninitialized state allows us to upgrade and reinitialize
the adapter.
FW_VERSION_T4 = 1.4.0.0
FW_VERSION_T5 = 0.0.0.0
FW_VERSION_T6 = 0.0.0.0
At this point driver supports above and greater than above version.
If FW in adapter < min FW_VERSION driver supports tries to upgrade the FW
If FW in adapter >= FW_VERSION driver supports then it follows normal path
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle TRACE_PKT, stack can sniff them on the first port
Add debubfs enrty to configure tracing for offload traffic like iWARP
& iSCSI for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the correct bits of PL Who Am I for the Source PF field which has
changed in T6
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to dump edc bist status for ECC data errors
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs entry 'use_backdoor' to enable backdoor access to read sge
context. By default, we read sge context's via firmware. In case of FW
issues, one can enable backdoor access via debugfs to dump sge context
for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating the driver to read the stats of only available channels. T6 and
later has only 2 channels
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Enhance cxgb4_t4_bar2_sge_qregs() and cxgb4_bar2_sge_qregs() to support T4
user mode mappings. Update all the current users as well.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The patch e85c9a7abfa4: ("cxgb4/cxgb4vf: Add code to calculate T5 BAR2
Offsets for SGE Queue Registers") from Dec 3, 2014, leads to the
following static checker warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:5358
t4_bar2_sge_qregs()
warn: should '(qid >> qpp_shift) << page_shift' be a 64 bit type?
This patch fixes it
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TP_PIO_{ADDR,DATA} registers are are in conflict with the firmware's
use of these registers. Added a routine to access it through FW LDST
cmd.
Access all TP_PIO_{ADDR,DATA} register access through new routine if FW
is alive. If firmware is dead, than fall back to indirect access.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grab the Adapter MAC Address out of the VPD and use it for the "debug"
network interface when either we can't contact the firmware
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar