1. It is really dangerous to have more than one
spinlock protecting the same information.
2. radeon_irq_set sometimes wasn't called with lock
protection, so it can happen that more than one
CPU would tamper with the irq regs at the same
time.
3. The pm.gui_idle variable was assuming that the 3D
engine wasn't becoming idle between testing the
register and setting the variable. So just remove
it and test the register directly.
v2: Also handle the hpd irq code the same way.
v3: Rename hpd parameter for clarification.
Signed-off-by: Christian Koenig <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
- Properly set up the RBs
- Properly set up the SPI
- Properly set up gb_addr_config
This should fix rendering issues on certain cards.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This closes a race seen with kexec where we enable PCI bus mastering
but the card has been reinitialised fully yet.
This was previously fixed by a patch from Jerome, but this should
close the race completely.
v2: add SI support as suggested by Alex.
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: agd5f: add new MAX_PIPES param
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The maximum number of pipes is needed by the user space compute
driver to calculate the number of wavefronts per thread group.
Signed-off-by: Tom Stellard <thomas.stellard@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current enabling of bus mastering in the drm midlayer allows a large
race condition under kexec. When a kexec'ed kernel re-enables bus mastering
for the GPU, previously setup dma blocks may cause writes to random pieces
of memory. On radeon the writeback mechanism can cause these sorts of issues.
This patch doesn't fix the problem, but it moves the bus master enable under
the individual drivers control so they can move enabling it until later in
their load cycle and close the race.
Fix for radeon kms driver will be in a follow-up patch.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Virtual address space are per drm client (opener of /dev/drm).
Client are in charge of virtual address space, they need to
map bo into it by calling DRM_RADEON_GEM_VA ioctl.
First 16M of virtual address space is reserved by the kernel.
Once using 2 level page table we should be able to have a small
vram memory footprint for each pt (there would be one pt for all
gart, one for all vram and then one first level for each virtual
address space).
Plan include using the sub allocator for a common vm page table
area and using memcpy to copy vm page table in & out. Or use
a gart object and copy things in & out using dma.
v2: agd5f fixes:
- Add vram base offset for vram pages. The GPU physical address of a
vram page is FB_OFFSET + page offset. FB_OFFSET is 0 on discrete
cards and the physical bus address of the stolen memory on
integrated chips.
- VM_CONTEXT1_PROTECTION_FAULT_DEFAULT_ADDR covers all vmid's >= 1
v3: agd5f:
- integrate with the semaphore/multi-ring stuff
v4:
- rebase on top ttm dma & multi-ring stuff
- userspace is now in charge of the address space
- no more specific cs vm ioctl, instead cs ioctl has a new
chunk
v5:
- properly handle mem == NULL case from move_notify callback
- fix the vm cleanup path
v6:
- fix update of page table to only happen on valid mem placement
v7:
- add tlb flush for each vm context
- add flags to define mapping property (readable, writeable, snooped)
- make ring id implicit from ib->fence->ring, up to each asic callback
to then do ring specific scheduling if vm ib scheduling function
v8:
- add query for ib limit and kernel reserved virtual space
- rename vm->size to max_pfn (maximum number of page)
- update gem_va ioctl to also allow unmap operation
- bump kernel version to allow userspace to query for vm support
v9:
- rebuild page table only when bind and incrementaly depending
on bo referenced by cs and that have been moved
- allow virtual address space to grow
- use sa allocator for vram page table
- return invalid when querying vm limit on non cayman GPU
- dump vm fault register on lockup
v10: agd5f:
- Move the vm schedule_ib callback to a standalone function, remove
the callback and use the existing ib_execute callback for VM IBs.
v11:
- rebase on top of lastest Linus
v12: agd5f:
- remove spurious backslash
- set IB vm_id to 0 in radeon_ib_get()
v13: agd5f:
- fix handling of RADEON_CHUNK_ID_FLAGS
v14:
- fix va destruction
- fix suspend resume
- forbid bo to have several different va in same vm
v15:
- rebase
v16:
- cleanup left over of vm init/fini
v17: agd5f:
- cs checker
v18: agd5f:
- reworks the CS ioctl to better support multiple rings and
VM. Rather than adding a new chunk id for VM, just re-use the
IB chunk id and add a new flags for VM mode. Also define additional
dwords for the flags chunk id to define the what ring we want to use
(gfx, compute, uvd, etc.) and the priority.
v19:
- fix cs fini in weird case of no ib
- semi working flush fix for ni
- rebase on top of sa allocator changes
v20: agd5f:
- further CS ioctl cleanups from Christian's comments
v21: agd5f:
- integrate CS checker improvements
v22: agd5f:
- final cleanups for release, only allow VM CS on cayman
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The 3D driver need to get the pipe to backend
map to certain things. Add a query to get the
info.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_pci_device_is_pcie duplicates the funcationality of pci_is_pcie.
Convert callers of the former to the latter. This has the side benefit
of removing an unnecessary search in the PCI configuration space due to
using a saved PCIe capability offset.
[airlied: update for new callsite]
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Out of the entire GART/VM subsystem, the hw designers changed
the location of 3 regs.
v2: airlied: add parameter for userspace to work from.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This abstracts the pci/platform interface out a step further,
we can go further but this is far enough for now to allow USB
to be plugged in.
The drivers now just call the init code directly for their
device type.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The CMASK RAM is for colorbuffer compression (used in conjunction
with MSAA). Only one user (filp) can access it.
The CMASK RAM access is managed in the same way as Hyper-Z, but there is
a separate ioctl, because an app that uses MSAA does not necessarily
have to use zbuffering.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to track the state of the switch in drivers, so that after s/r
we don't resume the card we've explicitly switched off before. Also
don't allow a userspace open to occur if we've switched the gpu off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds new functions for use by the drm core:
.get_vblank_timestamp() provides a precise timestamp
for the end of the most recent (or current) vblank
interval of a given crtc, as needed for the DRI2
implementation of the OML_sync_control extension.
It is a thin wrapper around the drm function
drm_calc_vbltimestamp_from_scanoutpos() which does
almost all the work and is shared across drivers.
.get_scanout_position() provides the current horizontal
and vertical video scanout position and "in vblank"
status of a given crtc, as needed by the drm for use by
drm_calc_vbltimestamp_from_scanoutpos().
The function is also used by the dynamic gpu reclocking
code to determine when it is safe to reclock inside vblank.
For that purpose radeon_pm_in_vbl() is modified to
accomodate a small change in the function prototype of
the radeon_get_crtc_scanoutpos() which is hooked up to
.get_scanout_position().
This code has been tested on AVIVO hardware, a RV530
(ATI Mobility Radeon X1600) in a Intel Core-2 Duo MacBookPro
and some R600 variant (FireGL V7600) in a single cpu
AMD Athlon 64 PC.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This seems to have gotten lost in the hyper-z merge.
Noticed by legume on IRC.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the current screwed but its ABI, ioctls for the drm, Linus pointed out that we could allow userspace to specify the allocation size, but we pass it to the driver which then uses it blindly to store a struct. Now if userspace specifies the allocation size as smaller than the driver needs, the driver can possibly overwrite memory.
This patch restructures the driver ioctls so we store the structure size we are expecting, and make sure we allocate at least that size. The copy from/to userspace are still restricted to the size the user specifies, this allows ioctl structs to grow on both sides of the equation.
Up until now we didn't really use the DRM_IOCTL defines in the kernel, so this cleans them up and adds them for nouveau.
v2:
fix nouveau pushbuf arg (thanks to Ben for pointing it out)
Reported-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This hasn't mattered up until the ioctl started using the value, and it fell
apart.
fixes fd.o 29340, Ubuntu LP 606081
[airlied: cleaned up whitespace and don't need an error before pushing]
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This interface allows userspace to request hyperz support, it probably
needs more locking, and really reporting that you can have hyperz is racy
since someone else might get it before you do.
v2: modify so we pass 0 valued packets to let DDX/r300c keep working.
also fixed incorrect 0x4f1c reference.
v3: fixup zb_bw_cntl so older drivers keep working
v4: add locking, fixup SC_HYPERZ_EN - patch stream to disable hiz
Signed-off-by: Dave Airlie <airlied@redhat.com>
This migrates a bunch of DRM_DEBUG->DRM_DEBUG_KMS so we can get more modesetting related info without all the other ioctl handling easily.
Also the PM code moves to DRM_DEBUG_DRIVER mostly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace needs this information to access tiled
buffers via the CPU.
v2: rebased on evergreen accel changes
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
By calling the ATIF method in the radeon driver we can make sure
that hotkeys such as the video switch key emit ACPI events when
pressed.
agd5f: fix warning
Signed-off-by: Alberto Milone <alberto.milone@canonical.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Return the crtc_id, not the counter value. They are not
necessarily the same.
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed to enable accel in the ddx. However,
due to a bug in older versions of the ddx, it relies
on accel being disabled in order to load properly on
evergreen chips. To maintain compatility, we add a new
get accel param and call that from the ddx. The old one
always returns false for evergreen cards.
[this fixes a regression with older userspaces on newer kernels].
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* anholt/drm-intel-next: (515 commits)
drm/i915: Fix out of tree builds
drm/i915: move fence lru to struct drm_i915_fence_reg
drm/i915: don't allow tiling changes on pinned buffers v2
drm/i915: Be extra careful about A/D matching for multifunction SDVO
drm/i915: Fix DDC bus selection for multifunction SDVO
drm/i915: cleanup mode setting before unmapping registers
drm/i915: Make fbc control wrapper functions
drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
drm/i915: Use spatio-temporal dithering on PCH
[MTD] Remove zero-length files mtdbdi.c and internal.ho
pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
libata: Fix several inaccuracies in developer's guide
slub: Fix bad boundary check in init_kmem_cache_nodes()
raid6: fix recovery performance regression
KEYS: call_sbin_request_key() must write lock keyrings before modifying them
KEYS: Use RCU dereference wrappers in keyring key type code
KEYS: find_keyring_by_name() can gain access to a freed keyring
ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
ALSA: take tu->qlock with irqs disabled
...
Userspace need to know the hw crtc id (0, 1, 2, ...) from the drm
crtc id. Bump the minor version so userspace can enable conditionaly
features depend on this.
V2 use num_crtc and avoid DRM_ERROR
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: Fix sparc regression in r300_scratch()
drm: make sure vblank interrupts are disabled at DPMS time
drm/radeon/kms/evergreen: No EnableYUV table
drm/radeon: 9800 SE has only one quadpipe
drm/radeon/kms: don't print error for legal crtcs.
drm/radeon/kms/evergreen: fix LUT setup
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Many new laptops now come with 2 gpus, one to be used for low power
modes and one for gaming/on-ac applications. These GPUs are typically
wired to the laptop panel and VGA ports via a multiplexer unit which
is controlled via ACPI methods.
4 combinations of systems typically exist - with 2 ACPI methods.
Intel/ATI - Lenovo W500/T500 - use ATPX ACPI method
ATI/ATI - some ASUS - use ATPX ACPI Method
Intel/Nvidia - - use _DSM ACPI method
Nvidia/Nvidia - - use _DSM ACPI method.
TODO:
This patch adds support for the ATPX method and initial bits
for the _DSM methods that need to written by someone with
access to the hardware.
Add a proper non-debugfs interface - need to get some proper
testing first.
v2: add power up/down support for both devices
on W500 puts i915/radeon into D3 and cuts power to radeon.
v3: redo probing methods, no DMI list, drm devices call to
register with switcheroo, it tries to find an ATPX method on
any device and once there is two devices + ATPX it inits the
switcher.
v4: ATPX msg handling using buffers - should work on more machines
v5: rearchitect after more mjg59 discussion - move ATPX handling to
radeon driver.
v6: add file headers + initial nouveau bits (to be filled out).
v7: merge delayed switcher code.
v8: avoid suspend/resume of gpu that is off
v9: rearchitect - mjg59 is always right. - move all ATPX code to
radeon, should allow simpler DSM also proper ATRM handling
v10: add ATRM support for radeon BIOS, add mutex to lock vgasr_priv
v11: fix bug in resuming Intel for 2nd time.
v12: start fixing up nvidia code blindly.
v13: blindly guess at finishing nvidia code
v14: remove radeon audio hacks - fix up intel resume more like upstream
v15: clean up printks + remove unnecessary igd/dis pointers
mount debugfs
/sys/kernel/debug/vgaswitcheroo/switch - should exist if ATPX detected
+ 2 cards.
DIS - immediate change to discrete
IGD - immediate change to IGD
DDIS - delayed change to discrete
DIGD - delayed change to IGD
ON - turn on not in use
OFF - turn off not in use
Tested on W500 (Intel/ATI) and T500 (Intel/ATI)
Signed-off-by: Dave Airlie <airlied@redhat.com>
This would allow us to properly unload others module like TTM if
initialization fails after we initiliazed TTM structure.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Userspace can query if acceleration is working or not true get
info ioctl and could fallback to software if for some reason
kernel failed to initialize KMS. This should allow to give a
working KMS setup in all case (even with non functionning accel).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We are splitting GPU & modeset init so that it's easier
to abord only remaining GPU init when somethings fails.
We want to always provide enough funcionalities to get
fbcon and a shadowfb X working. Only acceptable error
during initialization are memory allocation failure or
io mapping failure.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The previous patch assumes the ioctl already existed, when
it actually didn't.
It also didn't return the correct error code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes 3D apps timing out in the WAIT_VBLANK ioctl.
AVIVO bits compile-tested only.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds new set/get tiling interfaces where the pitch
and macro/micro tiling enables can be set. Along with
a flag to decide if this object should have a surface when mapped.
The only thing we need to allocate with a mapped surface should be
the frontbuffer. Note rotate scanout shouldn't require one, and
back/depth shouldn't either, though mesa needs some fixes.
It fixes the TTM interfaces along Thomas's suggestions, and I've tested
the surface stealing code with two X servers and not seen any lockdep issues.
I've stopped tiling the fbcon frontbuffer, as I don't see there being
any advantage other than testing, I've left the testing commands in there,
just flip the fb_tiled to true in radeon_fb.c
Open: Can we integrate endian swapping in with this?
Future features:
texture tiling - need to relocate texture registers TXOFFSET* with tiling info.
This also merges Michel's cleanup surfaces regs at init time patch
even though it makes sense on its own, this patch really relies on it.
Some PowerMac firmwares set up a tiling surface at the beginning of VRAM
which messes us up otherwise.
that patch is:
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It hasn't been used in ages, and having the user tell your how much
memory is being freed at free time is a recipe for disaster even if it
was ever used.
Signed-off-by: Eric Anholt <eric@anholt.net>
Christian Koenig