We've noticed that sometimes "MTD do_write_buffer(): software timeout"
message was printed out when writing to a Fujitsu NOR flash.
It turned out that this was because of a race in the timeout handling
do_write_buffer(). A small timeout of (HZ / 1000) + 1 is used there, and
sometimes if the timer interrupt handling takes more than one or even two
jiffies (which is 1-2 ms with HZ == 1000) and that interrupt happens just
after chip_ready() call, the driver bails out from a ready polling loop
despite the chip has actually become ready while all those interrupts were
handled. To deal with this issue, extra check for chip ready is neccessary on
timeout expiration (and the checks should better be reordered).
As do_write_oneword() uses the same approach, it needs to also be changed.
Signed-off-by: Konstantin Baidarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The following patch adds support for the TQ Systems TQM834x Boards.
Verified on TQM8349L.
This is a resubmit after integrating the suggested changes.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix two compile warnings that occur because of treating two
'unsigned long's as 'void *'s.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The assignement of a "const char *" to a "char *" variable
is emitting a warning with gcc 4.0. We cannot change
mtd->name to "const char *" as we have dynamic assignements
of the name. So casting is the correct solution here
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Nathan Roberts noticed the nand_write_ecc index into oobbuf goes out of
bounds when crossing an erase block boundary, causing incorrect OOB data
to be written and corrupting memory. Reset the index to zero after
re-preparing oobbuf for a new erase block.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In case of an odd offset, the result was shifted by 1 instead of 8
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Use map.virt instead of map.map_priv_1 since it has the correct type.
- Use readw/writew instead of dereferencing an ioremap'd cookie.
- Remove an unused variable.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Sharp Zaurus akita and borzoi models are large page flash devices.
This patch adds support for them to the sharpsl MTD NAND driver but
keeps the oob layout and bad block positions compatible with the Sharp
Zaurus 2.4 kernel and ROM bootloader.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change to the extended cfi table parsing for Intel NOR flash that uses
the info in the extended table to 'walk' the table rather than using
hard coding for various primary extended query table version numbers.
From: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added .owner initialisation to allow the
tracking of the device_driver owners when
built as a module
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added owner to device driver field for tracking
when loaded as a module.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added owner fields to the device_driver for tracking
ownership when built as a module
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Don't assume eraseblock size is power of 2.
Dataflash can have aligned eraseblock size.
From: Peter Menzebach <pm-mtd@mw-itcon.de>
Acked-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add density mask for better support of DDP chips.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Simple bad block table source and header files
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- cleaned up the partitions and include files
- added more flexible CS and address detection and setup
Regression tested on db1200 and db1550.
Signed-off-by: Pete Popov <ppopov@pacbell.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add support for "4G Systems MTX-1 Flash device", better known as meshcube.
From: Bruno Randolf <bruno.randolf@4g-systems.biz>
Signed-off-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The changes introduced allow to suspend/resume NAND flash.
A new state (FL_PM_SUSPENDED) is introduced, as well as
routines for mtd->suspend and mtd->resume to put the flash in
suspended state from software pov.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now we can use the generic platform driver
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Intel chip driver has a reboot notifier so no need to reset the chip here.
- Don't play with chip selects (platform code should do this if necessary).
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Update OMAP OneNAND mapping file using device driver model
- Remove board specific macro and values.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add OneNAND Sync. Burst Read support
Tested with OMAP platform
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
OneNAND is a new flash technology from Samsung with integrated SRAM
buffers and logic interface.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The bit mask used for oob size calculation was using 2 bits instead
of one. Fortunately the next bit has been 0 all the time.
Thanks to Nathan H. for pointing this out
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While this might be useful for all supported flash types, it is mandatory
for proper JFFS2 support with Sibley flash.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This updates the Primary Vendor-Specific Extended Query parsing to
version 1.4 in order to get the information about the Configurable
Programming Mode regions implemented in the Sibley flash, as well as
selecting the appropriate write command code.
This flash does not behave like traditional NOR flash when writing data.
While mtdblock should just work, further changes are needed for JFFS2 use.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This includes improved error handling/reporting plus some other
message cleanups.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This type of flash translation layer (FTL) is used by the Embedded BIOS
by General Software. It is known as the Resident Flash Disk (RFD), see:
http://www.gensw.com/pages/prod/bios/rfd.htm
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This adds support for the Nvidia Geforce 7800 series of cards to the
nvidiafb framebuffer driver. All it does is add the PCI device id for
the 7800, 7800 GTX, 7800 GO, and 7800 GTX GO cards to the module device
table for the nvidiafb.ko driver, so that nvidiafb.ko will actually work
on these cards.
I also added the relevant PCI device ids to linux/pci_ids.h
I tested it on my 7800 GTX here and it works like a charm. I now can
get framebuffer support on this card! Woo hoo!! Nothing like 200x75 text
mode to make your eyes BLEED. ;)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Konstantin Baidarov