commit 1e41568d73 ("Take ima_path_check()
in nfsd past dentry_open() in nfsd_open()") moved this code back to its
original location but missed the "else".
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] megaraid_sas: fix for 32bit apps
[SCSI] fcoe: Only rmmod fcoe.ko if there are no active connections
[SCSI] libfcoe: Send port LKA every FIP_VN_KA_PERIOD secs.
[SCSI] libfc: Don't assume response request present.
[SCSI] libfc: Fix e_d_tov ns -> ms scaling factor in PLOGI response.
[SCSI] libfc: call ddp setup for only FCP reads to avoid accessing junk fsp pointer
[SCSI] iscsi_tcp regression: remove bogus warn on in write path
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
sfc: SFE4002/SFN4112F: Widen temperature and voltage tolerances
sfc: Fix sign of efx_mcdi_poll_reboot() error in efx_mcdi_poll()
net-sysfs: Use rtnl_trylock in wireless sysfs methods.
net: Fix sysctl restarts...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: bump the UMS driver version number to indicate rv740 fix
drm/radeon/kms: free fence IB if it wasn't emited at IB free time
drm/ttm: fix caching problem on non-PAT systems.
drm/radeon/rv740: fix backend setup
drm/radeon/kms: fix shared ddc detection
drm/radeon/kms/rs600: add connector quirk
vgaarb: fix "target=default" passing
The temperature and voltage limits currently set on these boards are
too conservative and will cause the driver to stop the net device
erroneously in some systems.
Based on a review of the chip datasheets and advice from the designer
of these boards:
- Raise the maximum board temperatures to the specified maximum ambient
temperatures for their PHYs plus the expected temperature bias of the
board
- Raise the maximum controller temperature to 90 degrees
- Lower the minimum temperatures to 0 degrees
- Widen the voltage tolerances to at least +/- 10%
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_mcdi_poll() uses positive error numbers, matching the MCDI
protocol. It must negate the result of efx_mcdi_poll_reboot() which
returns the usual negative error numbers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wireless sysfs methods like the rest of the networking sysfs
methods are removed with the rtnl_lock held and block until
the existing methods stop executing. So use rtnl_trylock
and restart_syscall so that the code continues to work.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuck. It turns out that when we restart sysctls we were restarting
with the values already changed. Which unfortunately meant that
the second time through we thought there was no change and skipped
all kinds of work, despite the fact that there was indeed a change.
I have fixed this the simplest way possible by restoring the changed
values when we restart the sysctl write.
One of my coworkers spotted this bug when after disabling forwarding
on an interface pings were still forwarded.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to testcase and report from Brad Spengler:
--------------------
#include <stdio.h>
typedef int (* _wee)(void);
int main(void)
{
char buf[8] = { '\x81', '\xc7', '\xe0', '\x08', '\x81', '\xe8',
'\x00', '\x00' };
_wee wee;
printf("%p\n", &buf);
wee = (_wee)&buf;
wee();
return 0;
}
--------------------
TSB I-tlb load code tries to use andcc to check the _PAGE_EXEC_4U bit,
but that's bit 12 so it gets sign extended all the way up to bit 63
and the test nearly always passes as a result.
Use sethi to fix the bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
This lets UMS userspace know the rv740 fix is in. For KMS we can
consider the kernel release to be the v2.0.0 release so we don't need the
bump there.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If at IB free time fence wasn't emited that means the IB wasn't
scheduled because an error occured somewhere, thus we can free
then fence and mark the IB as free.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
http://bugzilla.kernel.org/show_bug.cgi?id=15328
This fixes a serious regression on AGP/non-PAT systems, where
pages were ending up in the wrong state and slowing down the
whole system.
[airlied: taken this from the bug as the other option is to revert
the change which caused it].
Tested-by: John W. Linville (in bug).
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes occlusion queries and rendering errors
on rv740 boards. Hardcoding the backend map is not an optimal
solution, but a better fix is being worked on.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just compare the i2c id since the i2c structs
may be slighly different.
Fixes fdo bug 26616.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs600 board lists DVI port as HDMI.
Fixes fdo bug 26605
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 77c1ff3982 fixed the userspace
pointer dereference, but introduced another bug pointed out by Eugene Teo
in RH bug #564264. Instead of comparing the point we were at in the string,
we instead compared the beginning of the string to "default".
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Reported-by: Eugene Teo <eteo@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It looks like this patch -
commit 7b2519afa1
Author: Yang, Bo <Bo.Yang@lsi.com>
Date: Tue Oct 6 14:52:20 2009 -0600
[SCSI] megaraid_sas: fix 64 bit sense pointer truncation
has caused a problem for 32bit programs with 64bit os -
http://bugzilla.kernel.org/show_bug.cgi?id=15001
fix by converting the user space 32bit pointer to a 64 bit one when
needed.
[jejb: fix up some 64 bit warnings]
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Cc: Bo Yang <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The HT extension channel settings require priv->staging_rxon.channel to be
accurate. However, iwl_set_rxon_ht was being called before iwl_set_rxon_channel
and thus HT40 could be broken unless another call to iwl_mac_config came in.
This problem was recently introduced by "iwlwifi: Fix to set correct ht
configuration"
The particular setting in which I noticed this was monitor mode:
iwconfig wlan0 mode monitor
ifconfig wlan0 up
./iw wlan0 set channel 64 HT40-
#./iw wlan0 set channel 64 HT40-
tcpdump -i wlan0 -y IEEE802_11_RADIO
would only catch HT40 packets if I issued the IW command twice.
From visual inspection, iwl_set_rxon_channel does not depend on
iwl_set_rxon_ht, so simply swapping them should be safe and fixes this problem.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the user enables breakpoints through dr7, he can choose
between "local" or "global" enable bits but given how linux is
implemented, both have the same effect.
That said we don't keep track how the user enabled the breakpoints
so when the user requests the dr7 value, we only translate the
"enabled" status using the global enabled bits. It means that if
the user enabled a breakpoint using the local enabled bit, reading
back dr7 will set the global bit and clear the local one.
Apps like Wine expect a full dr7 POKEUSER/PEEKUSER match for emulated
softwares that implement old reverse engineering protection schemes.
We fix that by keeping track of the whole dr7 value given by the user
in the thread structure to drop this bug. We'll think about
something more proper later.
This fixes a 2.6.32 - 2.6.33-x ptrace regression.
Reported-and-tested-by: Michael Stefaniuc <mstefani@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Maneesh Soni <maneesh@linux.vnet.ibm.com>
Cc: Alexandre Julliard <julliard@winehq.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Before we had a generic breakpoint API, ptrace was accepting
breakpoints on NULL address in x86. The new API refuse them,
without given strong reasons. We need to follow the previous
behaviour as some userspace apps like Wine need such NULL
breakpoints to ensure old emulated software protections
are still working.
This fixes a 2.6.32 - 2.6.33-x ptrace regression.
Reported-and-tested-by: Michael Stefaniuc <mstefani@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: K.Prasad <prasad@linux.vnet.ibm.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Maneesh Soni <maneesh@linux.vnet.ibm.com>
Cc: Alexandre Julliard <julliard@winehq.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
This removes 8 bytes of padding from struct inode on 64bit builds, and
so allows 1 more object/slab in the inode_cache when using slub.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
----
patch against 2.6.33-rc8
compiled & tested on x86_64 AMDX2
I've been running this patch for over a week with no obvious problems
regards
Richard
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make sure that automount "symlinks" are followed regardless of LOOKUP_FOLLOW;
it should have no effect on them.
Cc: stable@kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Earlier, Ingo Molnar posted a patch to make it so that the kernel would avoid
reading _PPC on his broken T60. Unfortunately, it seems that with Thomas
Renninger's patch last July to eliminate _PPC evaluations when the processor
driver loads, the kernel never actually reads _PPC at all! This is problematic
if you happen to boot your non-T60 computer in a state where the BIOS _wants_
_PPC to be something other than zero.
So, put the _PPC evaluation back into acpi_processor_get_performance_info if
ignore_ppc isn't 1.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Set the backlight to use the current brightness when loaded, rather than
always resetting the backlight to maximum brightness.
Fixes kernel bugzilla #14207
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Reported-by: Denis Mukhin <denis_mukhin@yahoo.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move I2C IR initialization from just after I2C bus setup to right
before non-I2C IR initialization. This avoids the case where an I2C IR
device is blocking audio support (at least the PV951 suffers from
this). It is also more logical to group IR support together,
regardless of the connectivity.
This fixes bug #15184:
http://bugzilla.kernel.org/show_bug.cgi?id=15184
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Regression was caused by my commit 6b35ca0d3d
which determined message size using sizeof rather than hardcoded constants.
Unfortunately pwc_set_shutter_speed reuses a 2 byte buffer for a one byte
message too so the sizeof was bogus in this case.
All other uses of sizeof checked and are ok.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This polling is needed if camera is in standby mode, but current exiting
condition is inverted.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cxusb uses the atbm8830 and lgs8gxx (not lgs8gl5) frontends and the
max2165 tuner, so it needs to select them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I'm trying to fix it on the GCC side (PR43007), but the module is
quite stupid in using ULL constants to operate on u32 values:
static int apply_frontend_param (struct dvb_frontend* fe, struct
dvb_frontend_parameters *param)
{
...
static const u32 ppm = 8000;
u32 spi_bias;
...
spi_bias *= 1000ULL;
spi_bias /= 1000ULL + ppm/1000;
which causes current GCC 4.5 to emit calls to __udivdi3 for i?86 again.
This patch fixes this issue.
Signed-off-by: Richard Guenther <rguenther@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It appears the wrong GPIO registers were used
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
mod_timer() takes an absolute time and not a delay as its argument.
Cc: <stable@kernel.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Due to lack of time, space, motivation, hardware and probably expertise,
I have reluctantly decided to orphan the DECnet code in the kernel.
Judging by the deafening silence on the linux-decnet mailing list I
suspect it's either not being used anyway, or the few people that are
using it are happy with their older kernels.
Signed-off-by: Christine Caulfield <christine.caulfield@googlemail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'outer_cache' variable is needed by the outer_inv_range(),
outer_clean_range() and outer_flush_range() functions, which are
declared as inline in asm/cacheflush.h. Otherwise drivers built
as a loadable module, which access these functions, will have
an undefined symbol.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: fix "acpi=ht" boot option
ACPI, i915: blacklist Clevo M5x0N bad_lid state
ACPI: fix High cpu temperature with 2.6.32
ACPI: dock: properly initialize local struct dock_station in dock_add()
ACPI: remove Asus P2B-DS from acpi=ht blacklist
thinkpad-acpi: wrong thermal attribute_group removed in thermal_exit()
ACPI: acpi_bus_{scan,bus,add}: return -ENODEV if no device was found
ACPI: Add NULL pointer check in acpi_bus_start
ACPI: processor: only evaluate _PDC once per processor
ACPI: processor: add kernel command line support for early _PDC eval
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: fix bo's fence association
drm/radeon/kms: fix indirect buffer management V2
drm/edid: Fix interlaced detailed timings to be frame size, not field.
drm/vmwgfx: Use fb handover mechanism instead of stealth mode.
drm/radeon/kms: use udelay for short delays
drm/nouveau: Force TV encoder DPMS reinit after resume.
drm/nouveau: use mutex for vbios lock
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/85xx: Fix SMP when "cpu-release-addr" is in lowmem
powerpc/85xx: Fix oops during MSI driver probe on MPC85xxMDS boards
Most laptops have keys that are intended to toggle all device state, not
just wifi. These are currently generally mapped to KEY_WLAN. As a result,
rfkill will only kill or enable wifi in response to the key press. This
confuses users and can make it difficult for them to enable bluetooth
and wwan devices.
This patch adds a new keycode, KEY_RFKILL. It indicates that the system
should toggle the state of all rfkillable devices.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
633aae2 "Input: i8042 - switch to using dev_pm_ops" removed handling
for PMSG_THAW, since we do not need to do anything during freeze and
thus it was thougt that thaw is not needed as well. However, there is
a period when interrupts are kept off, and if key happens to be pressed
during that time KBC becomes jammed. To avoid the jam we simply need
to poll KBC once during thaw.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We broke "acpi=ht" in 2.6.32 by disabling MADT parsing
for acpi=disabled. e5b8fc6ac1
This also broke systems which invoked acpi=ht via DMI blacklist.
acpi=ht is a really ugly hack,
but restore it for those that still use it.
http://bugzilla.kernel.org/show_bug.cgi?id=14886
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-airlied' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: Force TV encoder DPMS reinit after resume.
drm/nouveau: use mutex for vbios lock
Previous code did associate fence to bo before the fence was emited
and it also didn't lock protected access to ttm sync_obj member.
Both of this flaw leads to possible race between different code
path. This patch fix this by associating fence only once the fence
is emitted and properly lock protect access to sync_obj member of
ttm.
Fix:
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely similar others bugs
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is 3 different distinct states for an indirect buffer (IB) :
1- free with no fence
2- free with a fence
3- non free (fence doesn't matter)
Previous code mixed case 2 & 3 in a single one leading to possible
catastrophique failure. This patch rework the handling and properly
separate each case. So when you get ib we set the ib as non free and
fence status doesn't matter. Fence become active (ie has a meaning
for the ib code) once the ib is scheduled or free. This patch also
get rid of the alloc bitmap as it was overkill, we know go through
IB pool list like in a ring buffer as the oldest IB is the first
one the will be free.
Fix :
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely other bugs.
V2 remove the scheduled list, it's useless now, fix free ib scanning
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When the vmwgfx module is loaded on top of vesafb, it would operate in
stealth mode in parallel with vesafb, evicting VRAM on dropmaster.
Change that to use the vesafb handover mechanism, like other drmfb drivers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Chuck Ebbert