Introduce save_area_alloc(), save_area_boot_cpu(), save_area_add_regs()
and save_area_add_vxrs to deal with storing the CPU state in case of a
system dump. Remove struct save_area and save_area_ext, and create a new
struct save_area as a local definition to arch/s390/kernel/crash_dump.c.
Copy each individual field from the hardware status area to the save area,
storing the minimum of required data.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To collect the CPU registers of the crashed system allocated a single
page with memblock_alloc_base and use it as a copy buffer. Replace the
stop-and-store-status sigp with a store-status-at-address sigp in
smp_save_dump_cpus() and smp_store_status(). In both cases the target
CPU is already stopped and store-status-at-address avoids the detour
via the absolute zero page.
For kexec simplify s390_reset_system and call store_status() before
the prefix register of the boot CPU has been set to zero. Use STPX
to store the prefix register and remove dump_prefix_page.
Acked-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow to ipl from CCW based devices residing in any subchannel set.
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It turned out that SIGP set-multi-threading can only be done once.
Therefore switching to a different MT level after switching to
sclp.mtid_prev in the dump case fails.
As a symptom specifying the "nosmt" parameter currently fails for
the kdump kernel and the kernel starts with multi-threading enabled.
So fix this and issue diag 308 subcode 1 call after collecting the
CPU states for the dump. Also enhance the diag308_reset() function to
be usable also with enabled lowcore protection and prefix register != 0.
After the reset it is possible to switch the MT level again. We have
to do the reset very early in order not to kill the already initialized
console. Therefore instead of kmalloc() the corresponding memblock
functions have to be used. To avoid copying the sclp cpu code into
sclp_early, we now use the simple sigp loop method for CPU detection.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With this patch for kdump the s390 vector registers are stored into the
prepared save areas in the old kernel and into the REGSET_VX_LOW and
REGSET_VX_HIGH ELF notes for /proc/vmcore in the new kernel.
The NT_S390_VXRS_LOW note contains the lower halves of the first 16 vector
registers 0-15. The higher halves are stored in the floating point register
ELF note. The NT_S390_VXRS_HIGH contains the full vector registers 16-31.
The kernel provides a save area for storing vector register in case of
machine checks. A pointer to this save are is stored in the CPU lowcore
at offset 0x11b0. This save area is also used to save the registers for
kdump. In case of a dumped crashed kdump those areas are used to extract
the registers of the production system.
The vector registers for remote CPUs are stored using the "store additional
status at address" SIGP. For the dump CPU the vector registers are stored
with the VSTM instruction.
With this patch also zfcpdump stores the vector registers.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the loadparm is only supported for CCW IPL. But also for SCSI
IPL it can be specified either on the HMC load panel respectively
z/VM console or via diagnose 308.
So fix this for SCSI and add the required sysfs attributes for reading the
IPL loadparm and for setting the loadparm for re-IPL.
With this patch the following two sysfs attributes are introduced:
- /sys/firmware/ipl/loadparm (for system that have been IPLed from SCSI)
- /sys/firmware/reipl/fcp/loadparm
Because the loadparm is now available for SCSI and CCW it is moved
now from "struct ipl_block_ccw" to the generic "struct ipl_list_hdr".
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently zfpcdump can only collect registers for up to CONFIG_NR_CPUS
CPUss. This dependency is not necessary. So remove it by dynamically
allocating the save area array.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the following mechanisms are available to move active
Linux on System z instances between machines:
* z/VM 6.2 SSI (Single System Image)
* Suspend/resume
For moving Linux instances in this patch the term LGR (Linux Guest
Relocation) is used. Because such an operation is critical, it
should be detectable from Linux. With this patch for both, a live
system and a kernel dump, the information about LGRs is accessible.
To identify a guest, stsi and stfle data is used. A new function
lgr_info_log() compares the current data (lgr_info_cur) with the
last recorded one (lgr_info_last). In case the two data sets differ,
lgr_info_cur is logged to the "lgr" s390dbf.
The following trigger points call lgr_info_log():
* panic
* die
* kdump
* LGR timer
* PSW restart
* QDIO recovery
* resume
This patch also changes the s390dbf hex_ascii view. Now only printable ASCII
characters are shown.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch provides the architecture specific part of the s390 kdump
support.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The diagnose 308 call is the prefered method for clearing all ongoing I/O.
Therefore if it is available we use it instead of doing a manual reset.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Append scpdata to the kernel boot command line. If scpdata starts
with the equal sign (=), the kernel boot command line is replaced.
(For consistency with zIPL and IPL PARM parameters.)
To use scpdata for the kernel boot command line, scpdata must consist
of ascii characters only. If scpdata contains other characters,
scpdata is not appended to the kernel boot command line.
In addition, re-IPL is extended for setting scpdata for the next
Linux reboot.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Martin Schwidefsky