This patch adds i.MX7 thermal sensor support, most
of the i.MX7 thermal sensor functions are same with
i.MX6 except the registers offset/layout, so we move
those registers offset/layout definitions to soc data
structure.
i.MX7 uses single calibration data @25C, the calibration
data is located at OCOTP offset 0x4F0, bit[17:9], the
formula is as below:
Tmeas = (Nmeas - n1) + 25; n1 is the fuse value for 25C.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Due to the old method has already been marked as deprecated in binding
doc, so obviously it's better to update the example to new bindings
as well.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
On newer imx SOCs accessing OCOTP directly is wrong because the ocotp
clock needs to be enabled first. Add a binding for accessing the same
values through the imx-ocotp nvmem driver using nvmem-cells. This is
similar to other thermal drivers.
The old binding is preserved for compatibility and because it still
works fine on imx6qdl series chips.
In theory this problem could be solved by adding a reference to the
OCOTP clock instead but it is better to hide such details in a specific
nvmem driver.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
i.MX6SX has some new features of thermal interrupt function,
there are LOW, HIGH and PANIC irq for thermal sensor, so add
platform data to separate different thermal version;
The reset value of LOW ALARM is 0 which means the highest
temp, so the LOW ALARM will be triggered once irq is enabled,
so we need to correct it before enabling thermal irq;
Enable PANIC ALARM as critical trip point, it will trigger
system reset via SRC module once PANIC IRQ is triggered, it
is pure hardware function, so use it instead of software
reset by cooling device.
Signed-off-by: Anson Huang <b20788@freescale.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal sensor needs pll3_usb_otg when measuring temperature,
otherwise the temperature read will be incorrect, so need to
enable this clk before sensor working, for alarm function,
as hardware will take measurement periodically, so we should
keep this clk always on once alarm function is enabled.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This is based on the initial imx thermal work done by
Rob Lee <rob.lee@linaro.org> (Not sure if the email address is still
valid). Since he is no longer interested in the work and I have
rewritten a significant amount of the code, I just took the authorship
over from him.
It adds the imx thermal support using Temperature Monitor (TEMPMON)
block found on some Freescale i.MX SoCs. The driver uses syscon regmap
interface to access TEMPMON control registers and calibration data, and
supports cpufreq as the cooling device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Anson Huang