On i.MX53 and i.MX6, the CODA VPU can be reset by the System Reset Controller.
We can use this to get out of dire situations, for example after a picture
run timeout.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename the per-context prescan_failed variable to hold, as this is what the
flag does: it temporarily keeps the coda from running until new data is fed
into the bitstream buffer or stop_streaming is called on the input side.
A prescan failure on i.MX5 is one possible reason to enter this state, another
one is a picture run timeout on i.MX6.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The coda h.264 decoder also counts PIC_RUNs where no frame was decoded but
a frame was rotated out / marked as ready to be displayed. This causes an
offset between the incoming encoded frame's sequence number and the decode
sequence number returned by the coda. This patch introduces a sequence
counter offset variable to keep track of the difference.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the CODA reports macroblock errors, also set the VB2_BUF_STATE_ERROR flag
to alert userspace.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The coda driver advertises timestamp_type V4L2_BUF_FLAG_TIMESTAMP_COPY on
both queues, so we have to copy timestamps from input v4l2 buffers to the
corresponding destination v4l2 buffers. Since the h.264 decoder can reorder
frames, a timestamp queue is needed to keep track of and assign the correct
timestamp to destination buffers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In case no further buffers are queued after the stop command, restart
job scheduling explicitly.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Allow userspace to enable cyclic intra refresh by setting the number of
intra macroblocks per frame to a non-zero value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the bitrate control is set, the encoder works in CBR mode, dynamically
changing the quantization parameters to achieve a constant bitrate.
With the min/max QP controls the quantization parameters can be limited
to a given range.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver uses the genalloc API, which doesn't have stubs in
case GENERIC_ALLOCATOR is disabled.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This adds a new function coda_check_firmware that does the firmware
version checks so that this can be done only once from coda_probe
instead of every time the runtime pm framework resumes the coda.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch allows to use the runtime pm and generic pm domain frameworks
to completely gate power to the VPU if it is unused. This functionality
is available on i.MX6.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the mem2mem helpers introduced to get rid of some duplicated code.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Using the coda_mutex lock to serialize hardware access would cause
"INFO: possible circular locking dependency detected" lockdep warnings.
Since the possible locking paths are hard to follow, serialize hardware
access with a single workqueue thread. Ultimately the workqueue could
be converted to only do register setup and readout for per-command work
items.
Using the initialized context property, SEQ_END is only queued in
coda_release when needed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The h.264 decoder produces capture frames that are a multiple of the macroblock
size (16 pixels). To inform userspace about invalid pixel data at the edges,
use the active and padded composing rectangles on the capture queue.
The cropping information is obtained from the h.264 sequence parameter set.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This allows us to get rid of the now superfluous v4l2_m2m_get_vq check
in G_FMT. Also, we can use this to check the buffer type in G_SELECTION
later.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the CODA960 VPU in Freescale i.MX6 SoCs.
It enables h.264 and MPEG4 encoding and decoding support. Besides the usual
register shifting, the CODA960 gains frame memory control and GDI registers
that are set up for linear mapping right now, needs ENC_PIC_SRC_INDEX to be
set beyond the number of internal buffers for some reason, and has subsampling
buffers that need to be set up. Also, the work buffer size is increased to
80 KiB.
The CODA960 firmware spins if there is not enough input data in the bitstream
buffer. To make it continue, buffers need to be copied into the bitstream as
soon as they are queued. As the bitstream fifo is written into from two places,
it must be protected with a mutex. For that, using a threaded interrupt handler
is necessary.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Latest MFC v6 firmware requires tile mode and loop filter
setting to be done as part of Init buffer command, in sync
with v7. This patch adds this support for new v6 firmware.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For MFC firmwares, improved versions with bug fixes and
feature additions are released keeping the firmware version
including major and minor number same. The issue came with
the release of a new MFCv6 firmware with an interface change.
This patch adds the support of accepting multiple firmware
binaries for every version with the driver trying to load
firmwares starting from latest. This ensures full backward
compatibility regardless of which firmware version and kernel
version is used.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The function s5p_mfc_reload_firmware is exactly same as
s5p_mfc_load_firmware. So removing the duplicate function.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
drivers/built-in.o: In function `isp_video_open':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1253: undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `omap3isp_video_init':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1344: undefined reference to `vb2_dma_contig_init_ctx'
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1350: undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `omap3isp_video_cleanup':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1381: undefined reference to `vb2_dma_contig_cleanup_ctx'
make: *** [vmlinux] Error 1
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The bridge driver doesn't support interlaced formats, always return the
field order set to V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The CPB size is limited by the hardware. Add this limit to the s_fmt.
Signed-off-by: panpan liu <panpan1.liu@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
OVL and BTP IRAM buffers are never used, setup the bits for
for DBK/BIT/IP usage depending on CODA version in one place.
Also, use a simple allocator function and group IRAM addresses
and size in a coda_aux_buf structure.
This is done in preparation for CODA960 support.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media fixes from Mauro Carvalho Chehab:
"A series of driver fixes:
- fix DVB-S tuning with tda1071
- fix tuner probe on af9035 when the device has a bad eeprom
- some fixes for the new si2168/2157 drivers
- one Kconfig build fix (for omap4iss)
- fixes at vpif error path
- don't lock saa7134 ioctl at driver's base core level, as it now
uses V4L2 and VB2 locking schema
- fix audio at hdpvr driver
- fix the aspect ratio at the digital timings table
- one new USB ID (at gspca_pac7302): Genius i-Look 317 webcam"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca_pac7302: Add new usb-id for Genius i-Look 317
[media] tda10071: fix returned symbol rate calculation
[media] tda10071: fix spec inversion reporting
[media] tda10071: add missing DVB-S2/PSK-8 FEC AUTO
[media] tda10071: force modulation to QPSK on DVB-S
[media] hdpvr: fix two audio bugs
[media] davinci: vpif: missing unlocks on error
[media] af9035: override tuner id when bad value set into eeprom
[media] saa7134: use unlocked_ioctl instead of ioctl
[media] media: v4l2-core: v4l2-dv-timings.c: Cleaning up code wrong value used in aspect ratio
[media] si2168: firmware download fix
[media] si2157: add one missing parenthesis
[media] si2168: add one missing parenthesis
[media] staging: tighten omap4iss dependencies
If bitrate is not set, the encoder is running in VBR mode, with the
I- and P-frame quantization parameters configured from userspace.
For the quantization parameters, 0 is a valid value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently the rotator unit is used to copy decoded frames out into buffers
provided by videobuf2. Since the CODA reports the I/P/B frame type of the
last decoded frame, and this frame will be copied out in a later device_run,
depending on display order, we have to store the frame type until such time.
This patch also adds the B-frame type.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
fc906b6d "Remove special clock usage in driver" removed
initialization of MFC special clock, arguing that there's
no need to do it explicitly, since it's one of MFC gate clock's
dependencies and gets enabled along with it. However, there's
no promise of keeping this hierarchy across Exynos SoC
releases, therefore this approach fails to provide a stable,
portable solution.
Out of all MFC versions, only v6 doesn't use special clock at all.
For other versions log a message only in case clk_get fails,
as not all the devices with the same MFC version require
initializing the clock explicitly.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In the s5p_mfc_alloc_firmware() function there are some mistakes
where the code checks whether the DMA memory is properly allocated or
not.
First of all dma_alloc_coherent() returns NULL in case of error.
The code also checked two times fw_virt_addr, ignoring
the bank2_virt pointer.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pixel color components can be scaled using either bilinear interpolation
or a multitap filter. The multitap filter provides better results, but
can't be selected when the alpha layer need to be scaled down by more
than 1/2.
Disable alpha scaling when the input has a fixed alpha value, and
program the UDS to output a fixed alpha value in that case. This ensures
the multitap filter will be used whenever possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Expose the background color to userspace through the V4L2_CID_BG_COLOR
control.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The BRU outputs premultiplied colors, enable color data normalization
when the format configured at the output of the pipeline isn't
premultiplied.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adjust the BRU blending formula to avoid the multiplication by alpha
when the corresponding input format is premultiplied. As this requires
access to the RPFs connected to the BRU inputs from the BRU module,
store pointers to the RPFs in the BRU structure when validating the
pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The control is used to configure the fixed alpha channel value, when
reading from memory in the RPF or writing to memory in the WPF.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Support ARGB formats on the RPF side by reading the alpha component from
memory and on the WPF side by writing it to memory.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver ignores the alpha component on output video nodes and
hardcodes the alpha component to 0 on capture video nodes. Make this
explicit by exposing XRGB formats.
Compatibility with existing userspace applications is handled by
selecting the XRGB format corresponding to the requested old RGB format.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VSP1 stores the video pipelines' input (RPF) to output (WPF)
mappings in a WPF register. An RPF must never be associated with
multiple WPFs, even if all of those WPFs but one are unused, otherwise
the hardware won't function properly.
The driver doesn't ensure this correctly as it never clears the
mappings. An RPF used with one WPF and later with a different WPF will
lead to malfunction, as it will be associated with two WPFs. Clear the
mappings at stream off time to fix this.
Reported-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the subdev pointer directly to_vsp1_pipeline() macro instead of
casting from the subdev to the wpf object and back to the subdev.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The control value is currently stored in the SRU structure by the
control set handler and written to the hardware at stream on time,
making control set during streaming ineffective. Fix it by writing to
the registers from within the control set handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The default value isn't set and defaults to 0, which isn't in the 1-6
min-max range. Fix it by setting the default value to 1.
This shoud have been caught when checking the control handler error
field at initialization time, but the check was missing. Add it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When setting a control directly on a subdev node the VSP1 driver doesn't
guarantee that the device is powered on. This leads to crashes when the
control handlers writes to hardware registers. One easy way to fix this
is to ensure that the device gets powered on when a subdev node is
opened. However, this consumes power unnecessarily, as there's no need
to power the device on when setting formats on the pipeline.
Furthermore, control handler setup at entity init time suffers from the
same problem as the device isn't powered on easier.
Fix this by extend the entity base object to setup the control handler
automatically when starting the stream. Entities must then skip writing
to registers in the set control handler when not streaming, which can be
tested with the new vsp1_entity_is_streaming() helper function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modify the vsp1_device_get() function to return an error code instead of
a pointer to the VSP1 device, and use the return value in the callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Video nodes created and initialized in the RPF and WPF init code paths
are never unregistered, and the related resources (videobuf alloc
context and media entity) never released.
Fix this by storing a pointer to the vsp1_video object in vsp1_entity
and calling vsp1_video_cleanup() from vsp1_entity_destroy(). This also
allows simplifying the init error code paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the pipeline was already stopped when stopping the stream, no
frame end interrupt will be generated and the driver will time out
waiting for the pipeline to stop.
Fix this by setting the pipeline state to STOPPED when the pipeline is
idle waiting for frames to process, and to STOPPING at stream stop time
only when the pipeline is currently RUNNING.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
videobuf2 expects no buffer to be owned by the driver when the
stop_stream queue operation returns. As the vsp1 driver fails to do so,
a warning is generated at stream top time.
Fix this by releasing all buffers queued on the IRQ queue in the
stop_stream operation handler and marking them as erroneous.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit d9b45ed3d8 ("v4l: vsp1: Support
multi-input entities") reworked pipeline routing configuration and
introduced a bug by writing to the entities routing registers without
first checking whether the entity had a routing register. This results
in overwriting the value at offset 0 of the device register space when
stopping the stream.
Fix this by skipping routing register write for entities without a
routing register.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l2_pix_format structure has no reserved field. It is embedded in
the v4l2_framebuffer structure which has no reserved fields either, and
in the v4l2_format structure which has reserved fields that were not
previously required to be zeroed out by applications.
To allow extending v4l2_pix_format, inline it in the v4l2_framebuffer
structure, and use the priv field as a magic value to indicate that the
application has set all v4l2_pix_format extended fields and zeroed all
reserved fields following the v4l2_pix_format field in the v4l2_format
structure.
The availability of this API extension is reported to userspace through
the new V4L2_CAP_EXT_PIX_FORMAT capability flag. Just checking that the
priv field is still set to the magic value at [GS]_FMT return wouldn't
be enough, as older kernels don't zero the priv field on return.
To simplify the internal API towards drivers zero the extended fields
and set the priv field to the magic value for applications not aware of
the extensions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than having two unions for all types just keep 'val' and
'cur.val' and use the p_cur and p_new unions to access all others.
The only reason for keeping 'val' and 'cur.val' is that it is used
all over, so converting this as well would be a huge job.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While VIDIOC_QUERYCTRL is limited to 32 bit min/max/step/def values
for controls, the upcoming VIDIOC_QUERY_EXT_CTRL isn't. So increase
the internal representation to 64 bits in preparation.
Because of these changes the msi3101 driver has been modified slightly
to fix a formatting issue (%d becomes %lld), vivi had to be modified
as well to cope with the new 64-bit min/max values and the PIXEL_RATE
control in a few sensor drivers required proper min/max/def values.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since all the drivers that use `struct v4l2_fh' use the core
priority checking, the setting of the flag in the drivers can
be removed.
Signed-off-by: Ramakrishnan Muthukrishnan <ramakrmu@cisco.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
A check for CONFIG_DM644X_VIDEO_PORT_ENABLE was added in v2.6.32. The
related Kconfig symbol was never added so this check has always
evaluated to false. Remove that check.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We recently changed some locking around so we need some new unlocks on
the error paths.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sh_mobile_ceu_camera and sh_mobile_csi2 drivers are only useful on
SuperH and shmobile unless build testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch change MACH_MX27 dependency to SOC_IMX27 for MX2 camera
driver, since MACH_MX27 symbol is scheduled for removal.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That driver hasn't been really maintained for a long time. It doesn't
compile in any way, it includes non-existent headers, has no users,
and marked as "BROKEN" more than year. Due to these factors, mx1_camera
is now removed from the tree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The R-Car Video Input driver is only useful on shmobile unless build
testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The platform data is a single word, so simply copy
it into the device's private data structure than
keeping a copy of the pointer.
This will make changing to device-tree binding
easier as it is one allocation instead of two.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
devm_kzalloc() allocations are freed when the device is unbound. But if a
certain path fails and the allocated memory cannot be used anyway it is
better to free it explicitly immediately. This patch does exactly this if
asynchronous group probing in scan_async_group() fails after memory has
been allocated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace resource handling in the driver with managed device resource.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove bogus 'numbuffers' and 'bufsize' module options. The number of buffers and
buffer sizes are determined by VIDIOC_REQBUFS and VIDIOC_S_FMT and the amount of
available memory (in the case of the MMAP stream I/O mode) and not by module
options.
These module params are a left-over from the original montavista code that used
these parameters to pre-allocate the memory needed for the buffers. The code that
allocated those buffers was never upstreamed since by the time the drivers were
added to the kernel the TI cmem module could be used in combination with the
USERPTR mode to reserve and pass physically contiguous memory pointers around.
These days of course CMA is used instead of cmem.
This patch removes these module options altogether since they no longer do what
they originally were designed for. They should never have been part of the
upstreamed code in the first place, so they've been pointless ever since
2.6.32 when this driver first appeared in the mainline kernel.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The field is assigned but never read, remove it.
This fixes a bug caused by the struct vb2_buffer field not being be the
very first field of the vsp1_video_buffer buffer structure as required
by videobuf2.
Cc: stable@vger.kernel.org
Reported-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull OMAP3 updates from Mauro Carvalho Chehab:
"Some driver improvements on OMAP3. This series depend on some iommu
patches already merged"
* 'topic/omap3isp' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (26 commits)
[media] omap3isp: Rename isp_buffer isp_addr field to dma
[media] omap3isp: Move to videobuf2
[media] v4l: vb2: Add a function to discard all DONE buffers
[media] omap3isp: Cancel all queued buffers when stopping the video stream
[media] omap3isp: Move buffer irqlist to isp_buffer structure
[media] omap3isp: Move queue irqlock to isp_video structure
[media] omap3isp: Move queue mutex to isp_video structure
[media] omap3isp: queue: Don't build scatterlist for kernel buffer
[media] omap3isp: Use the ARM DMA IOMMU-aware operations
[media] omap3isp: queue: Use sg_alloc_table_from_pages()
[media] omap3isp: queue: Map PFNMAP buffers to device
[media] omap3isp: queue: Fix the dma_map_sg() return value check
[media] omap3isp: queue: Allocate kernel buffers with dma_alloc_coherent
[media] omap3isp: queue: Inline the ispmmu_v(un)map functions
[media] omap3isp: queue: Merge the prepare and sglist functions
[media] omap3isp: queue: Use sg_table structure
[media] omap3isp: queue: Move IOMMU handling code to the queue
[media] omap3isp: video: Set the buffer bytesused field at completion time
[media] omap3isp: ccdc: Use the DMA API for FPC
[media] omap3isp: ccdc: Use the DMA API for LSC
...
Pull updates and DT support for media engines from Mauro Carvalho Chehab.
For Analog Devices ADV7604 and the Renesas VSP1 video processing engines.
* 'topic/vsp1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] v4l: vsp1: Add DT support
[media] v4l: vsp1: Add DT bindings documentation
[media] v4l: vsp1: Add BRU support
[media] v4l: vsp1: Support multi-input entities
[media] v4l: vsp1: uds: Enable scaling of alpha layer
[media] v4l: vsp1: Remove unexisting rt clocks
* 'topic/adv76xx' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (21 commits)
[media] adv7604: Add LLC polarity configuration
[media] adv7604: Set HPD GPIO direction to output
[media] adv7604: Add endpoint properties to DT bindings
[media] adv7604: Add DT support
[media] adv7604: Specify the default input through platform data
[media] adv7604: Support hot-plug detect control through a GPIO
[media] adv7604: Sort headers alphabetically
[media] adv7604: Replace *_and_or() functions with *_clr_set()
[media] adv7604: Store I2C addresses and clients in arrays
[media] adv7604: Inline the to_sd function
[media] v4l: subdev: Remove deprecated video-level DV timings operations
[media] adv7604: Remove deprecated video-level DV timings operations
[media] adv7604: Add pad-level DV timings support
[media] adv7604: Make output format configurable through pad format operations
[media] adv7604: Add sink pads
[media] adv7604: Remove subdev control handlers
[media] adv7604: Add adv7611 support
[media] adv7604: Cache register contents when reading multiple bits
[media] adv7604: Add 16-bit read functions for CP and HDMI
[media] adv7604: Don't put info string arrays on the stack
...
The video enum_dv_timings operation is deprecated and unused. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video-level enum_dv_timings and dv_timings_cap operations are
deprecated in favor of the pad-level versions. All subdev drivers
implement the pad-level versions, switch to them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video-level enum_dv_timings and dv_timings_cap operations are
deprecated in favor of the pad-level versions. All subdev drivers
implement the pad-level versions, switch to them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video-level enum_dv_timings and dv_timings_cap operations are
deprecated in favor of the pad-level versions. All subdev drivers
implement the pad-level versions, switch to them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings operation is deprecated. Implement the
pad-level version of the operation to prepare for the removal of the
video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When stopping a video stream the driver waits for ongoing DMA opeations
to complete for the currently active buffer, but doesn't release the
non-active queued buffers. This isn't a problem in most cases as the
video device is usually closed after the stream is stopped, which will
release all the buffers. However the problem would generate a warning
when switching to videobuf2. Fix it by cancelling all buffers after DMA
operations have completed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This prepares for the move to videobuf2.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This prepares for the move to videobuf2.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This prepares for the move to videobuf2.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The scatterlist is not needed for those buffers, don't build it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Attach an ARM DMA I/O virtual address space to the ISP device. This
switches to the IOMMU-aware ARM DMA backend, we can thus remove the
explicit calls to the OMAP IOMMU map and unmap functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the custom implementation with a call to the scatterlist helper
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Userspace PFNMAP buffers need to be mapped to the device like the
userspace non-PFNMAP buffers in order for the DMA mapping implementation
to create IOMMU mappings when we'll switch to the IOMMU-aware DMA
mapping backend.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
dma_map_sg() can merge sglist entries, and can thus return a number of
mapped entries different than the original value. Don't consider this as
an error.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
And retrieve the related sg table using dma_get_sgtable().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ispmmu_vmap() and ispmmu_vunmap() functions are just wrappers around
omap_iommu_vmap() and omap_iommu_vunmap(). Inline them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In preparation for the switch to the DMA API merge the two functions
that handle buffer preparation for the USERPTR cases (both page-backed
and non page-backed memory).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the sglen and sglist fields stored in the buffer structure with
an sg_table. This allows using the sg table allocation helper function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As a preparation for the switch from the OMAP IOMMU API to the DMA API
move all IOMMU handling code from the video node implementation to the
buffers queue implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l buffer bytesused field is a value that will be returned to
userspace when the buffer gets dequeued. As such it doesn't need to be
set early at buffer queue time. Move the assignment to buffer completion
in the omap3isp_video_buffer_next() function to prepare for the video
buffers queue refactoring.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the OMAP-specific IOMMU API usage by the DMA API for FPC. The
table is now allocated using dma_alloc_coherent() and the related sg
table is retrieved using dma_get_sgtable() for sync operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the OMAP-specific IOMMU API usage by the DMA API for LSC. The
table is now allocated using dma_alloc_coherent() and the related sg
table is retrieved using dma_get_sgtable() for sync operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the OMAP-specific IOMMU API usage by the DMA API. All buffers
are now allocated using dma_alloc_coherent() and the related sg table is
retrieved using dma_get_sgtable() for sync operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver stores the IOMMU mapped iovm struct pointer in the buffer
structure but only needs the iovm sg table. Store the sg table instead
to prepare the migration to the DMA API.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The fields store buffer addresses as seen from the device. The first one
is used with an external DMA engine while the second one is used with
the ISP DMA engine. As they're never used together, merge them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move code common between the isp_stat_bufs_alloc_dma() and
isp_stat_bufs_alloc_iommu() functions to isp_stat_bufs_alloc().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The WARN_ON statements in the buffer allocation functions try to catch
conditions where buffers would have already been allocated. As the
buffers are explicitly freed right before being allocated this can't
happen.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The macro is meant to test whether the statistics engine uses an
external DMA engine to transfer data or supports DMA directly. As both
cases will be supported by DMA coherent buffers rename the macro to
ISP_STAT_USES_DMAENGINE for improved clarity.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The g_std and s_std operations are video-related, move them to the video
ops where they belong.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Drops check for #ifdef __KERNEL__, because this header is a Kernel
only header, where this define is always true.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds supports to return -ENODATA to *std calls
if the selected output does not support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds suppport to return -ENODATA for *dv_timings calls
if the current output does not support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch uses SIMPLE_DEV_PM_OPS, and drops unneeded members
from io_usrs, usrs and makes use of vb2 helepers instead.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch groups the v4l2_ioctl_ops and align them appropriately.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops cropcap as this driver doesnt support cropping.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes some modprobe parameters, without any reason
or description. I was supposed to not merge this patch, but It
was merged by mistake.
Revert it while nobody provides a good description for such patch.
This reverts commit b952662f27.
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When a resolution change point is reached, queue an event to signal the
userspace that a new set of buffers is required before decoding can
continue.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch moves the initalization of video device to a
single place and uses macro to define the driver name and
use it appropriately on the required places.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
the started member was indicating whether streaming was started
or not, this can be determined by vb2 offering, this patch replaces
the started member from struct common_obj with appropriate vb2 calls.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This field is set, but not used anymore. Remove it.
No functional changes.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops reserving contigiuos memory for the device,
as now with CMA support there is no need of this.
This patch also prepares to removal of config_params.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds support to use v4l2_fh_open() and vb2_fop_release,
which allows to drop driver specific struct vpif_fh, as this is handeled
by core. This patch also drops vpif_g/s_priority as this handeled
by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to reinvent the wheel. Just use the already existing
functions for that.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops unnecessary check from start_streaming() callback
as this is already done in try/s_fmt and some minor code cleanups,
drops check for vb2_is_streaming() as this check is done by vb2
itself before calling this callback.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch sets the sizes[0] of plane according to the fmt passed
or which is being set in the channel, in both MMAP and USERPTR buffer
type.
This patch also move the calculation of offests(vpif_calculate_offsets())
to queue_setup() callback as after queue_setup() callback the
application is no longer allowed to change format, and prepares to
removal of config_params.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch improve vpif_buffer_prepare() callback, as buf_prepare()
callback is never called with invalid state and check for
vb2_plane_vaddr(vb, 0) is dropped as payload check should
be done unconditionally.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops buf_cleanup() callback as this callback
is never called with buffer state active.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds support to release the buffer by calling
vb2_buffer_done(), with state marked as VB2_BUF_STATE_QUEUED
if start_streaming() call back fails.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch makes use of vb2_ops_wait_prepare/finish helper functions.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops the buf_init() callback as init
of buf list is not required.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch moves the initalization of vb2 queue and
the DMA context to probe() and clean up in remove()
callback respectively.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch fixes following checkpatch warning, and alongside
renames the DAVINCIHD_DISPLAY_H to VPIF_DISPLAY_H.
WARNING: Unnecessary space before function pointer arguments
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds supports to return -ENODATA to *std calls
if the selected output does not support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds suppport to return -ENODATA for *dv_timings calls
if the current output does not support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch uses SIMPLE_DEV_PM_OPS, and drops unneeded members
from io_usrs, usrs and makes use of vb2 helepers instead.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch gorups the v4l2_ioctl_ops and align them appropriately.
No functional changes.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops cropcap as this driver doesnt support cropping.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch moves the initalization of video device to a
single place and uses macro to define the driver name and
use it appropraitely in required places.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
the started member was indicating whether streaming was started
or not, this can be determined by vb2 offering, this patch replaces
the started member from struct common_obj with appropriate vb2 calls.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch drops numbuffers member from struct common_obj
as this was not required.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The common->memory field is set but not used anywhere. Drop it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops reserving contigiuos memory for the device,
as now with CMA support there is no need of this.
This patch also prepares to removal of config_params.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As fbuffers is not used anymore, remove it.
No functional changes.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds support to use v4l2_fh_open() and vb2_fop_release,
which allows to drop driver specific struct vpif_fh, as this is handeled
by core. This patch also drops vpif_g/s_priority as this handeled
by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to reinvent the wheel. Just use the already existing
functions for that.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops unnecessary check from start_streaming() callback
as this is already done in try/s_fmt and some minor code cleanups,
drops check for vb2_is_streaming() as this check is done by vb2
itself before calling this callback.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch sets the sizes[0] of plane according to the fmt passed
or which is being set in the channel, in both MMAP and USERPTR buffer
type.
This patch also move the calculation of offests(vpif_calculate_offsets())
to queue_setup() callback as after queue_setup() callback the
application is no longer allowed to change format, and prepares to
removal of config_params.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch improve vpif_buffer_prepare() callback, as buf_prepare()
callback is never called with invalid state and check for
vb2_plane_vaddr(vb, 0) is dropped as payload check should
be done unconditionally.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops buf_cleanup() callback as this callback
is never called with buffer state active.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds support to release the buffer by calling
vb2_buffer_done(), with state marked as VB2_BUF_STATE_QUEUED
if start_streaming() call back fails.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch makes use of vb2_ops_wait_prepare/finish helper functions.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch drops the buf_init() callback as init
of buf list is not required.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch moves the initalization of vb2 queue and
the DMA context to probe() and clean up in remove()
callback respectively.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All platforms supported by this driver are going to get device tree
support in this kernel release so remove code that would have been
actually not used any more.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ensure dma_free_coherent() is not called with incorrect arguments
and only when the memory was actually allocated. This will prevent
possible crashes on error paths of the top level media device driver,
when fimc-is device gets unregistered and its driver detached.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable@vger.kernel.org # for v3.15
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
CONFIG_COMMON_CLK is not enabled on S5PV210 platform, so include
some clk API data structures conditionally to avoid compilation
errors. These #ifdefs will be removed for next kernel release,
when the S5PV210 platform moves to DT and the common clk API.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable@vger.kernel.org # for 3.15
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds core support for v8 encoder. This
patch also adds register definitions and buffer size
requirements for H264 & VP8 encoding, needed for new
firmware version v8 for MFC
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
[k.debski@samsung.com: Change MFC version macro name to MFC_V8_BIT]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds variant data and core support for
V8 decoder. This patch also adds the register definition
file for new firmware version v8 for MFC.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
[k.debski@samsung.com: Change MFC version macro name to MFC_V8_BIT]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
MFC versions support a different set of formats, this specially applies
to the raw YUV formats. This patch changes enum_fmt, so that it only
reports formats that are supported by the used MFC version.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The patch adding the v6 version of MFC changed the default format for
the CAPTURE queue, but this also affects the v5 version. This patch
solves this problem by checking the MFC version before assigning the
default format.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Renaming the IS_MFCV7 macro to IS_MFCV7_PLUS for the
addition of MFCv8 support which reuses the v7 code.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch is needed in preparation to add MFC V8
where the register offsets are changed w.r.t MFC V6/V7.
This patch adds variants of MFC V6 and V7 while
accessing MFC registers. Registers are kept in mfc context
and are initialized to a particular MFC variant during probe,
which is used instead of macros.
This avoids duplication of the code for MFC variants
V6 & V7, and reduces the if_else checks while accessing
registers of different MFC variants.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The register S5P_FIMV_D_INIT_BUFFER_OPTIONS holds good for v6
firmware too. So moving the definition from v7 regs to v6.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Update the MPEG4 decoder scratch buffer size as per the
new v6 firmware. This updation is increasing the size and so
is backward compatible with older v6 firmwares.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently, for formats that are not H264, MFC driver will check
the consumed stream size returned by the firmware and, based on that,
will try to decide whether the bitstream buffer contained more than
one frame. If the size of the buffer is larger than the consumed
stream, it assumes that there are more frames in the buffer and that the
buffer should be resubmitted for decode. This rarely works though and
actually introduces problems, because:
- v7 firmware will always return consumed stream size equal to whatever
the driver passed to it when running decode (which is the size of the whole
buffer), which means we will never try to resubmit, because the firmware
will always tell us that it consumed all the data we passed to it;
- v6 firmware will return the number of consumed bytes, but will not
include the padding ("stuffing") bytes that are allowed after the frame
in VP8. Since there is no way of figuring out how many of those bytes
follow the frame without getting the frame size from IVF headers (or
somewhere else, but not from the stream itself), the driver tries to guess that
padding size is not larger than 4 bytes, which is not always true;
The only way to make it work is to queue only one frame per buffer from
userspace and the check in the kernel is useless and wrong for VP8.
So adding VP8 also along with H264 to disallow re-submitting of buffer
back to hardware for decode.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Scratch buffer size updated for vp8 encoding as per
the latest v7 firmware. As the new macro increases the
scratch buffer size, it is backward compatible with the older
firmware too.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently, we allocate private codec buffers on STREAMON, which may fail
if we are out of memory. We don't check for failure though, which will
make us crash with the codec accessing random memory.
We shouldn't be failing STREAMON with out of memory errors though. So move
the allocation of private codec buffers to REQBUFS for OUTPUT queue. Also,
move MFC instance opening and closing to REQBUFS as well, as it's tied to
allocation and deallocation of private codec buffers.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for a new flow to fix issues with streamon, which
should not be allocating buffer memory.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- Honor return values from vb2_reqbufs on REQBUFS(0).
- Do not set the number of allocated buffers to 0 if userspace tries
to request buffers again without freeing them.
- There is no need to verify correct instance state on reqbufs, as we will
verify this in queue_setup().
- There is also no need to verify that vb2_reqbufs() was able to allocate enough
buffers (pb_count) and call buf_init on that many buffers (i.e. dst_buf_count
is at least pb_count), because this will be verified by second queue_setup()
call as well and vb2_reqbufs() will fail otherwise.
- Only verify state is MFCINST_INIT when allocating, not when freeing.
- Refactor and simplify code.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Timestamps for destination buffers are assigned by copying them from
corresponding source buffers when the decode operation results in a frame
being outputted to a destination buffer. But the decision when to do this, i.e.
whether the decode operation on current source buffer produced a destination
frame, is wrongly based on "display status". Display status reflects the status
of the destination buffer, not source.
This used to work for firmwares version <= 6, because in addition to the above,
we'd check the decoded frame type register, which was set to "skipped" if
a destination frame was not produced, exiting early from
s5p_mfc_handle_frame_new().
Firmware >=7 does not set the frame type register for frames that were not
decoded anymore though, which results in us wrongly overwriting timestamps of
previously decoded buffers (firmware reports the same destination buffer address
as previously decoded one if a frame wasn't decoded during current operation).
To do it properly, we should be basing our decision to copy the timestamp on the
status of the source buffer, i.e. "decode status". The decode status register
values are confusing, because in its case "display" means "a frame has been
outputted to a destination buffer". We should copy if "decode and display"
is returned in it. This also works on <= v6 firmware, which behaves in the same
way with regards to decode status register.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the missing mutex_destroy(), when the driver is removed.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are no need to store resource struct and IRQ in the driver
internal structure.
This patch remove these fields and improve error handling by using
proper return codes from devm_ioremap_resource() and devm_request_irq().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VIDIOC_STREAMOFF clears the encoder's destination queue -- routines run
from the interrupt handler cannot assume that the queue is non-empty.
Signed-off-by: John Sheu <sheu@google.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename the memory block resource "vpe_csc" to "csc" since it also exists within
the VIP IP block. This would make the name more generic, and both VPE and VIP DT
nodes in the future can use it.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add selection ioctl ops. For VPE, cropping makes sense only for the input to
VPE(or V4L2_BUF_TYPE_VIDEO_OUTPUT/MPLANE buffers) and composing makes sense
only for the output of VPE(or V4L2_BUF_TYPE_VIDEO_CAPTURE/MPLANE buffers).
For the CAPTURE type, V4L2_SEL_TGT_COMPOSE results in VPE writing the output
in a rectangle within the capture buffer. For the OUTPUT type, V4L2_SEL_TGT_CROP
results in selecting a rectangle region within the source buffer.
Setting the crop/compose rectangles should successfully result in
re-configuration of registers which are affected when either source or
destination dimensions change, set_srcdst_params() is called for this purpose.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some parameters of the VPE descriptors were understood incorrectly. They are now
fixed. The fixes are explained as follows:
- When adding an inbound data descriptor to the VPDMA descriptor list, we intend
to use c_rect as the cropped region fetched by VPDMA. Therefore, c_rect->width
shouldn't be used to calculate the line stride, the original image width
should be used for that. We add a 'width' argument which gives the buffer
width in memory.
- frame_width and frame_height describe the complete width and height of the
client to which the channel is connected. If there are multiple channels
fetching data and providing to the same client, the above 2 arguments should
be the width and height of the region covered by all the channels. In the case
where there is only one channel providing pixel data to the client
(like in VPE), frame_width and frame_height should be the cropped width and
cropped height respectively. The calculation of these params is done in the
vpe driver now.
- start_h and start_v is also used in the case of multiple channels to describe
where each channel should start filling pixel data. We don't use this in VPE,
and pass 0s to the vpdma_add_in_dtd() helper.
- Some minor changes are made to the vpdma_add_out_dtd() helper. The c_rect
param is used for specifying the 'composition' target, and 'width' is added
to calculate the line stride.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For OMAP and DRA7x, we generally allocate video and graphics buffers through
omapdrm since the corresponding omap-gem driver provides DMM-Tiler backed
contiguous buffers. omapdrm is a dma-buf exporter. These buffers are used by
other drivers in the video pipeline.
Add VB2_DMABUF flag to the io_modes of the vb2 output and capture queues. This
allows the driver to import dma shared buffers.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
vpe fops(vpe_open in particular) should be called only when VPDMA firmware
is loaded. File operations on the video device are possible the moment it is
registered.
Currently, we register the video device for VPE at driver probe, after calling
a vpdma helper to initialize VPDMA and load firmware. This function is
non-blocking(it calls request_firmware_nowait()), and doesn't ensure that the
firmware is actually loaded when it returns.
We remove the device registration from vpe probe, and move it to a callback
provided by the vpe driver to the vpdma library, through vpdma_create().
The ready field in vpdma_data is no longer needed since we always have firmware
loaded before the device is registered.
A minor problem with this approach is that if the video_register_device
fails(which doesn't really happen), the vpe platform device would be registered.
however, there won't be any v4l2 device corresponding to it.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This will help to debug driver, allows us to see the full name of
the device through /proc/interrupts.
CPU0
...
69: 0 mxc-avic 53 10023000.coda
...
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch adds support to release the buffer by calling
vb2_buffer_done(), with state marked as VB2_BUF_STATE_QUEUED
if start_streaming() call back fails.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions.The label err_register is removed as it is no longer required.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
devm_ioremap_resource() returns a pointer to the remapped memory or
an ERR_PTR() encoded error code on failure. Fix the checks inside
csc_create() and sc_create() accordingly.
Cc: Archit Taneja <archit@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Archit Taneja<archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTfR2zAAoJEHm+PkMAQRiG3noH/2s+KUge3qO2M+AmxttUo74B
+npAMdbqYR3MdEiwxYZfsHcMu4Ye/IKLcrh4pydB5hI2mdjtGkH1bnmia0f1ve/c
Z/a0256+W8gWp7mcUBqSNztqLPAWa7wKOqNdLjj5idr1BSj6u8im+fQ9FBh2woki
1fyYAuq/60lq4CMOKJvkA95V1Ome/jO+8tS4PguOgsCETQxCVFGurZcBbG3Mx5Y3
v+ioCqeRc6GvxPFR6YngnTZCrsLxSRT3tnO2Qy5zX7dxjIQkCEbvIckpBQv01Y3R
wNUaX+2Jae207igxrEv8CjmCFnmZFuUI15aWWCy6fOS/j8bjuk6ThYJO8N4ZBM0=
=2ShG
-----END PGP SIGNATURE-----
Merge tag 'v3.15-rc6' into patchwork
Linux 3.15-rc6
* tag 'v3.15-rc6': (1314 commits)
Linux 3.15-rc6
Btrfs: send, fix incorrect ref access when using extrefs
Btrfs: fix EIO on reading file after ioctl clone works on it
scripts/checksyscalls.sh: Make renameat optional
asm-generic: Add renameat2 syscall
ia64: add renameat2 syscall
parisc: add renameat2 syscall
m68k: add renameat2 syscall
sysfs: make sure read buffer is zeroed
ahci: imx: PLL clock needs 100us to settle down
PCI: Wrong register used to check pending traffic
target: fix memory leak on XCOPY
random: fix BUG_ON caused by accounting simplification
clk: tegra: Fix wrong value written to PLLE_AUX
staging: rtl8723au: Do not reset wdev->iftype in netdev_close()
ACPI / video: Revert native brightness quirk for ThinkPad T530
staging: rtl8723au: Use correct pipe type for USB interrupts
crush: decode and initialize chooseleaf_vary_r
libceph: fix corruption when using page_count 0 page in rbd
arm64: fix pud_huge() for 2-level pagetables
...
Pull media fixes from Mauro Carvalho Chehab:
"Most of the changes are drivers fixes (rtl28xuu, fc2580, ov7670,
davinci, gspca, s5p-fimc and s5c73m3).
There is also a compat32 fix and one infoleak fixup at the media
controller"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] V4L2: fix VIDIOC_CREATE_BUFS in 64- / 32-bit compatibility mode
[media] V4L2: ov7670: fix a wrong index, potentially Oopsing the kernel from user-space
[media] media-device: fix infoleak in ioctl media_enum_entities()
[media] fc2580: fix tuning failure on 32-bit arch
[media] Prefer gspca_sonixb over sn9c102 for all devices
[media] media: davinci: vpfe: make sure all the buffers unmapped and released
[media] staging: media: davinci: vpfe: make sure all the buffers are released
[media] media: davinci: vpbe_display: fix releasing of active buffers
[media] media: davinci: vpif_display: fix releasing of active buffers
[media] media: davinci: vpif_capture: fix releasing of active buffers
[media] s5p-fimc: Fix YUV422P depth
[media] s5c73m3: Add missing rename of v4l2_of_get_next_endpoint() function
[media] rtl28xxu: silence error log about disabled rtl2832_sdr module
[media] rtl28xxu: do not hard depend on staging SDR module
S5PC210 SoC doesn't support encoding NV12 raw images. Remove
relavant flag from the respective entry in the sjpeg_formats
array.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch fixes build break occurring when there is no support
for Device Tree turned on in the kernel configuration. In such
case only the driver variant for S5PC210 SoC will be available.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Prevent decompression of a JPEG 4:2:0 with odd width to
the YUV 4:2:0 compliant formats for Exynos4x12 SoCs and
adjust capture format to RGB565 in such a case. This is
required because the configuration would produce a raw
image with broken luma component.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch fixes jpeg sysmmu page fault on Exynos4x12 SoCs.
During encoding Exynos4x12 SoCs access wider memory area
than it results from Image_x and Image_y values written to
the JPEG_IMAGE_SIZE register. In order to avoid sysmmu page
fault apply proper output buffer size alignment.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove erroneous guard preventing successful execution of
g_selection callback in case the driver variant is different
from SJPEG_S5P.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Simplify the code by adding m2m_ops field to the
s5p_jpeg_variant structure which allows to avoid
"if" statement in the s5p_jpeg_probe function.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change the driver variant check from "is not S5PC210"
to "is Exynos4" while checking whether YUV format needs
to be downgraded in order to prevent upsampling which
is not supported by Exynos4 SoCs family.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Simplify the code by adding fmt_ver_flag field
to the s5p_jpeg_variant structure which allows
to avoid "if" statement in the s5p_jpeg_find_format
function.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This formula did not take into account the required tiled alignement for
NV12MT format. As this was already computed an stored in payload array
initially, reuse that value.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Testing showed that HW produces BGR32 rather then RGB32 as exposed
in the driver. The documentation seems to state the pixels are stored
in little endian order.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
[s.nawrocki@samsung.com] replaced "BGRB888, 32 bpp" with "BGRA8888, 32 bpp"
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Depth and payload is defined per memory plane. It's better to iterate using
number of memory planes. This was not causing much issue since the rest
of the arrays involved where intialized to zero.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the sub-device did not report any tvnorms, then disable the STD
ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement support for the VSP1 DT bindings in the VSP1 driver. The
driver now first retrieves platform data either from the platform data
pointer or by reading the device tree node, and then validates it
regardless of the platform data source.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Blend ROP Unit performs blending and ROP operations for up to four
sources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Scaling of the alpha layer is disabled as both the RPF and WPF are
configured to hardcode the alpha value to 255. This results in a 0 alpha
value at the UDS output, making the image invisible when alpha blended
in the BRU. Fix it by enabling scaling of the alpha layer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VSP1 has no rt clock. Remove them from the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The stop_streaming op is only called if streaming is in progress,
so drop the unnecessary 'if (!vb2_is_streaming(vq))' check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vb2 core ignores any return code from the stop_streaming op.
And there really isn't anything it can do anyway in case of an error.
So change the return type to void and update any drivers that implement it.
The int return gave drivers the idea that this operation could actually
fail, but that's really not the case.
The pwc amd sdr-msi3101 drivers both had this construction:
if (mutex_lock_interruptible(&s->v4l2_lock))
return -ERESTARTSYS;
This has been updated to just call mutex_lock(). The stop_streaming op
expects this to really stop streaming and I very much doubt this will
work reliably if stop_streaming just returns without really stopping the
DMA.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch migrates the vpfe driver to use v4l2_fh for
priority handling.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch migrates the vpbe driver to use v4l2_fh for
priority handling. This also fixes v4l2-compliance test.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VIDEO_TIMBERDALE selects TIMB_DMA which itself depends on
MFD_TIMBERDALE, so VIDEO_TIMBERDALE should either select or depend on
MFD_TIMBERDALE as well. I chose to make it depend on it because I
think it makes more sense and it is consistent with what other options
are doing.
Adding a "|| HAS_IOMEM" to the TIMB_DMA dependencies silenced the
kconfig warning about unmet direct dependencies but it was wrong:
without MFD_TIMBERDALE, TIMB_DMA is useless as the driver has no
device to bind to.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
from commit-id: b3379c6201
"vb2: only call start_streaming if sufficient buffers are queued"
the vb2 framework warns on (WARN_ON()) if all the active buffers
are not released when streaming is stopped, initially the vb2 silently
released the buffer internally if the buffer was not released by
the driver.
This patch fixes following issue:
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:2011 __vb2_queue_cancel+0x1a0/0x218()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpbe_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252e0c>] (__vb2_queue_cancel+0x1a0/0x218)
[<c0252e0c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpbe_display_release+0x60/0x230)
[<c025a65c>] (vpbe_display_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:1095 vb2_buffer_done+0x1e0/0x224()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpbe_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252c28>] (vb2_buffer_done+0x1e0/0x224)
[<c0252c28>] (vb2_buffer_done) from [<c0252e3c>] (__vb2_queue_cancel+0x1d0/0x218)
[<c0252e3c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpbe_display_release+0x60/0x230)
[<c025a65c>] (vpbe_display_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a2 ]---
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
from commit-id: b3379c6201
"vb2: only call start_streaming if sufficient buffers are queued"
the vb2 framework warns on (WARN_ON()) if all the active buffers
are not released when streaming is stopped, initially the vb2 silently
released the buffer internally if the buffer was not released by
the driver.
Also this patch moves the disabling of interrupts from relase() callback
to stop_streaming() callback as which needs to be done ideally.
This patch fixes following issue:
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:2011 __vb2_queue_cancel+0x1a0/0x218()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252e0c>] (__vb2_queue_cancel+0x1a0/0x218)
[<c0252e0c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:1095 vb2_buffer_done+0x1e0/0x224()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252c28>] (vb2_buffer_done+0x1e0/0x224)
[<c0252c28>] (vb2_buffer_done) from [<c0252e3c>] (__vb2_queue_cancel+0x1d0/0x218)
[<c0252e3c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a2 ]---
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
from commit-id: b3379c6201
"vb2: only call start_streaming if sufficient buffers are queued"
the vb2 framework warns on (WARN_ON()) if all the active buffers
are not released when streaming is stopped, initially the vb2 silently
released the buffer internally if the buffer was not released by
the driver.
Also this patch moves the disabling of interrupts from relase() callback
to stop_streaming() callback as which needs to be done ideally.
This patch fixes following issue:
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:2011 __vb2_queue_cancel+0x1a0/0x218()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_capture Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252e0c>] (__vb2_queue_cancel+0x1a0/0x218)
[<c0252e0c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:1095 vb2_buffer_done+0x1e0/0x224()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_capture Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252c28>] (vb2_buffer_done+0x1e0/0x224)
[<c0252c28>] (vb2_buffer_done) from [<c0252e3c>] (__vb2_queue_cancel+0x1d0/0x218)
[<c0252e3c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a2 ]---
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All YUV 422 has 16bit per pixels.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The dequed CAPTURE_MPLANE type buffers don't contain the flags that the
originally queued OUTPUT_MPLANE type buffers have. This breaks compliance.
Copy the source v4l2_buffer flags to the destination v4l2_buffer flags before
they are dequed.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vpe driver wasn't setting the correct field parameter for dequed CAPTURE
type buffers for the case where the captured output is progressive.
Set the field to V4L2_FIELD_NONE for the completed destination buffers when
the captured output is progressive.
For OUTPUT type buffers, a queued buffer's field is forced to V4L2_FIELD_NONE
if the pixel format(configured through s_fmt for the buffer type
V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE specifies) the field type isn't interlaced.
If the pixel format specified was V4L2_FIELD_ALTERNATE, and the queued buffer's
field isn't V4L2_FIELD_TOP or V4L2_FIELD_BOTTOM, the vb2 buf_prepare op returns
an error.
This ensures compliance, and that the dequeued output and captured buffers
contain the field type that the driver used internally.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Zero out the reserved formats in v4l2_pix_format_mplane and
v4l2_plane_pix_format members of the returned v4l2_format pointer when passed
through TRY_FMT ioctl.
This ensures that the user doesn't interpret the non-zero fields as some data
passed by the driver, and ensures compliance.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vpe output and capture queues are initially configured to default values in
vpe_open(). A G_FMT before any S_FMTs will result in these values being
populated.
The colorspace and bytesperline parameter of this initial configuration are
incorrect. This breaks compliance when as we get 'TRY_FMT(G_FMT) != G_FMT'.
Fix the initial queue configuration such that it wouldn't need to be fixed by
try_fmt.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The bus_info parameter in v4l2_capabilities expects a 'platform_' prefix. This
wasn't done in the driver and hence was breaking compliance. Update the bus_info
parameter accordingly.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
querycap currently returns V4L2_CAP_VIDEO_M2M as a capability, this should be
V4L2_CAP_VIDEO_M2M_MPLANE instead, as the driver supports multiplanar formats.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The minimum width and height for VPE input/output was kept as 128 pixels. VPE
doesn't have a constraint on the image height, it requires the image width to
be at least 16 bytes.
Change the minimum supported dimensions to 32x32. This allows us to de-interlace
qcif content. A smaller image size than 32x32 didn't make much sense, so stopped
at this.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video_device struct is currently embedded in the driver data struct vpe_dev.
A vpe_dev instance is allocated by the driver, and the memory for the vfd is a
part of this struct.
The v4l2 core, however, manages the removal of the vfd region, through the
video_device's .release() op, which currently is the helper
video_device_release. This causes memory corruption, and leads to issues when
we try to re-insert the vpe module.
Use the video_device_release_empty helper function instead.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VPE has a ctrl parameter which decides how many mem to mem transactions the
active job from the job queue can perform.
The driver's job_ready() made sure that the number of ready source buffers are
sufficient for the job to execute successfully. But it didn't make sure if
there are sufficient ready destination buffers in the capture queue for the
VPE output.
If the time taken by VPE to process a single frame is really slow, then it's
possible that we don't need to imply such a restriction on the dst queue, but
really fast transactions(small resolution, no de-interlacing) may cause us to
hit the condition where we don't have any free buffers for the VPE to write on.
Add the extra check in job_ready() to make sure we have the sufficient amount
of destination buffers.
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull exynos media updates from Mauro Carvalho Chehab:
"These are the remaining patches I have for the merge windows. It
basically adds a new sensor and adds the needed DT bits for it to
work"
* 'topic/exynos' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] s5p-fimc: Remove reference to outdated macro
[media] s5p-jpeg: Fix broken indentation in jpeg-regs.h
[media] exynos4-is: Add the FIMC-IS ISP capture DMA driver
[media] exynos4-is: Add support for asynchronous subdevices registration
[media] exynos4-is: Add clock provider for the SCLK_CAM clock outputs
[media] exynos4-is: Use external s5k6a3 sensor driver
[media] V4L: s5c73m3: Add device tree support
[media] V4L: Add driver for s5k6a3 image sensor
[media] Documentation: devicetree: Update Samsung FIMC DT binding
[media] Documentation: dt: Add binding documentation for S5C73M3 camera
[media] Documentation: dt: Add binding documentation for S5K6A3 image sensor
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
Add a video capture node for the FIMC-IS ISP IP block. The Exynos4x12
FIMC-IS ISP IP block has 2 DMA interfaces that allow to capture raw
Bayer and YUV data to memory. Currently only the DMA2 output is and
raw Bayer data capture is supported.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for registering external sensor subdevs using
v4l2-async API. The async API is used only for sensor subdevs
and only for booting from DT.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds clock provider so the the SCLK_CAM0/1 output clocks
can be accessed by image sensor devices through the clk API.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes the common fimc-is-sensor driver for image sensors
that are normally controlled by the FIMC-IS firmware. The FIMC-IS
driver now contains only a table of properties specific to each sensor.
The sensor properties required for the ISP's firmware are parsed from
device tree and retrieved from the internal table, which is selected
based on the compatible property of an image sensor.
To use the Exynos4x12 internal ISP the S5K6A3 sensor driver (drivers/
media/i2c/s5k6a3.c) is now required.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The "Renesas Corporation" listed in the copyright notice doesn't exist.
Replace it with "Renesas Electronics Corporation" and update the
copyright years.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since the introduction of the new OMAP DSS DVI connector driver in
commit 348077b154 ("OMAPDSS: Add new DVI
Connector driver"), DVI outputs report a new display type of
OMAP_DISPLAY_TYPE_DVI instead of OMAP_DISPLAY_TYPE_DPI. Handle the new
type in the IRQ handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
try_fmt should just set field to NONE and not return an error if
a different field was passed.
buf_prepare should check if the field passed in from userspace has a
supported field value. At the moment only NONE is supported and ANY
is mapped to NONE.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- Set the sequence counters correctly.
- Copy timestamps, timecode, relevant buffer flags and field from
the received buffer to the outgoing buffer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
To keep the vb2 buffer administration in balance stop_streaming() must
return any pending buffers to the vb2 framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no reason why we shouldn't enable this here.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This resolves an issue raised by v4l2-compliance: if the given format does
not exist, then pick a default format.
While there is an exception regarding this for TV capture drivers, this
m2m driver should do the right thing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The default of 1 second is a bit painful, switch to a 25 Hz framerate.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no any reason to use comma here.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for MBUS YUV10 BT656 and BT601 formats at rcar driver.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
interruptible_sleep_on is racy and going away. In the arv driver that
race has probably never caused problems since it would require a whole
video frame to be captured before the read function has a chance to
go to sleep, but using wait_event_interruptible lets us kill off the
old interface. In order to do this, we have to slightly adapt the
meaning of the ar->start_capture field to distinguish between not having
started a frame and having completed it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If NO_DMA=y:
warning: (VIDEO_DM6446_CCDC && VIDEO_DM355_CCDC && VIDEO_DM365_ISIF && VIDEO_OMAP2_VOUT && VIDEO_SH_VOU && VIDEO_VIU && VIDEO_TIMBERDALE && VIDEO_MX1 && VIDEO_OMAP1) selects VIDEOBUF_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/built-in.o: In function `videobuf_vm_close':
videobuf-dma-contig.c:(.text+0x407aa0): undefined reference to `videobuf_queue_cancel'
drivers/built-in.o: In function `__videobuf_dc_alloc':
videobuf-dma-contig.c:(.text+0x407ba2): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `__videobuf_mmap_mapper':
videobuf-dma-contig.c:(.text+0x407d44): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `free_buffer':
sh_vou.c:(.text+0x41f73a): undefined reference to `videobuf_waiton'
drivers/built-in.o: In function `sh_vou_poll':
sh_vou.c:(.text+0x41f884): undefined reference to `videobuf_poll_stream'
drivers/built-in.o: In function `sh_vou_buf_prepare':
sh_vou.c:(.text+0x41fdf6): undefined reference to `videobuf_iolock'
drivers/built-in.o: In function `sh_vou_reqbufs':
sh_vou.c:(.text+0x4203b0): undefined reference to `videobuf_reqbufs'
drivers/built-in.o: In function `sh_vou_querybuf':
sh_vou.c:(.text+0x42040a): undefined reference to `videobuf_querybuf'
drivers/built-in.o: In function `sh_vou_qbuf':
sh_vou.c:(.text+0x42045e): undefined reference to `videobuf_qbuf'
drivers/built-in.o: In function `sh_vou_dqbuf':
sh_vou.c:(.text+0x4204c2): undefined reference to `videobuf_dqbuf'
drivers/built-in.o: In function `sh_vou_streamon':
sh_vou.c:(.text+0x420572): undefined reference to `videobuf_streamon'
drivers/built-in.o: In function `sh_vou_streamoff':
sh_vou.c:(.text+0x4205d2): undefined reference to `videobuf_streamoff'
drivers/built-in.o: In function `sh_vou_mmap':
sh_vou.c:(.text+0x420c46): undefined reference to `videobuf_mmap_mapper'
VIDEO_SH_VOU selects VIDEOBUF_DMA_CONTIG, which bypasses its dependency on
HAS_DMA. Make VIDEO_SH_VOU depend on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function never checked if width and height are correct. Add such
a check so the v4l2-compliance tool returns OK again for vivi.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If start_streaming fails then any queued buffers must be given back
to the vb2 core.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In commit 02f142ecd2 support was added to
start_streaming to return -ENOBUFS if insufficient buffers were queued
for the DMA engine to start. The vb2 core would attempt calling
start_streaming again if another buffer would be queued up.
Later analysis uncovered problems with the queue management if start_streaming
would return an error: the buffers are enqueued to the driver before the
start_streaming op is called, so after an error they are never returned to
the vb2 core. The solution for this is to let the driver return them to
the vb2 core in case of an error while starting the DMA engine. However,
in the case of -ENOBUFS that would be weird: it is not a real error, it
just says that more buffers are needed. Requiring start_streaming to give
them back only to have them requeued again the next time the application
calls QBUF is inefficient.
This patch changes this mechanism: it adds a 'min_buffers_needed' field
to vb2_queue that drivers can set with the minimum number of buffers
required to start the DMA engine. The start_streaming op is only called
if enough buffers are queued. The -ENOBUFS handling has been dropped in
favor of this new method.
Drivers are expected to return buffers back to vb2 core with state QUEUED
if start_streaming would return an error. The vb2 core checks for this
and produces a warning if that didn't happen and it will forcefully
reclaim such buffers to ensure that the internal vb2 core state remains
consistent and all buffer-related resources have been correctly freed
and all op calls have been balanced.
__reqbufs() has been updated to check that at least min_buffers_needed
buffers could be allocated. If fewer buffers were allocated then __reqbufs
will free what was allocated and return -ENOMEM. Based on a suggestion from
Pawel Osciak.
__create_bufs() doesn't do that check, since the use of __create_bufs
assumes some advance scenario where the user might want more control.
Instead streamon will check if enough buffers were allocated to prevent
streaming with fewer than the minimum required number of buffers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The buf_finish op should always work, so change the return type to void.
Update the few drivers that use it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds a new struct of_endpoint which is then embedded in struct
v4l2_of_endpoint and contains the endpoint properties that are not V4L2
(or even media) specific: the port number, endpoint id, local device tree
node and remote endpoint phandle. of_graph_parse_endpoint parses those
properties and is used by v4l2_of_parse_endpoint, which just adds the
V4L2 MBUS information to the containing v4l2_of_endpoint structure.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch moves the parsing helpers used to parse connected graphs
in the device tree, like the video interface bindings documented in
Documentation/devicetree/bindings/media/video-interfaces.txt, from
drivers/media/v4l2-core/v4l2-of.c into drivers/of/base.c.
This allows to reuse the same parser code from outside the V4L2
framework, most importantly from display drivers.
The functions v4l2_of_get_next_endpoint, v4l2_of_get_remote_port,
and v4l2_of_get_remote_port_parent are moved. They are renamed to
of_graph_get_next_endpoint, of_graph_get_remote_port, and
of_graph_get_remote_port_parent, respectively.
Since there are not that many current users yet, switch all of
them to the new functions right away.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Use the correct name in the comment describing function
omap3isp_module_sync_is_stopping().
isp_isr() never returned IRQ_NONE, remove the comment saying so.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel