devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Barry Song <Baohua.Song@csr.com>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
This is support for the ARM Chromebook, originally scheduled
as a "late" pull request. Since it's already late now, we
can combine this into the existing next/dt2 branch.
* late/dt:
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
Pull i2c changes from Wolfram Sang:
- an arbitration driver. While the driver is quite simple, it caused
discussion if we need additional arbitration on top of the one
specified in the I2C standard. Conclusion is that I accept a few
generic mechanisms, but not very specific ones.
- the core lost the detach_adapter() call. It has no users anymore and
was in the way for other cleanups. attach_adapter() is sadly still
there since there are users waiting to be converted.
- the core gained a bus recovery infrastructure. I2C defines a way to
recover if the data line is stalled. This mechanism is now in the
core and drivers can now pass some data to make use of it.
- bigger driver cleanups for designware, s3c2410
- removing superfluous refcounting from drivers
- removing Ben Dooks as second maintainer due to inactivity. Thanks
for all your work so far, Ben!
- bugfixes, feature additions, devicetree fixups, simplifications...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: xiic: must always write 16-bit words to TX_FIFO
i2c: octeon: use HZ in timeout value
i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
i2c: designware-pci: drop superfluous {get|put}_device
i2c: designware-plat: drop superfluous {get|put}_device
i2c: davinci: drop superfluous {get|put}_device
MAINTAINERS: Ben Dooks is inactive regarding I2C
i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
i2c: at91: convert to dma_request_slave_channel_compat()
i2c: mxs: do error checking and handling in PIO mode
i2c: mxs: remove races in PIO code
i2c-designware: switch to use runtime PM autosuspend
i2c-designware: use usleep_range() in the busy-loop
i2c-designware: enable/disable the controller properly
i2c-designware: use dynamic adapter numbering on Lynxpoint
i2c-designware-pci: use managed functions pcim_* and devm_*
i2c-designware-pci: use dev_err() instead of printk()
i2c-designware: move to managed functions (devm_*)
i2c: remove CONFIG_HOTPLUG ifdefs
i2c: s3c2410: Add SMBus emulation for block read
...
The TX_FIFO register is 10 bits wide. The lower 8 bits are the data to be
written, while the upper two bits are flags to indicate stop/start.
The driver apparently attempted to optimize write access, by only writing a
byte in those cases where the stop/start bits are zero. However, we have
seen cases where the lower byte is duplicated onto the upper byte by the
hardware, which causes inadvertent stop/starts.
This patch changes the write access to the transmit FIFO to always be 16 bits
wide.
Signed off by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
I've been debugging the abnormal operation of i2c on octeon. If a process is
terminated by signal in the middle of i2c operation, next i2c read operation
which is done by another process was failed. So i changed to ignore signal in
the middle of i2c operation. After that the problem was not reproduced.
Signed-off-by: Eunbong Song <eunb.song@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Sekhar Nori <nsekhar@ti.com>
The i2c-arb-gpio-challenge driver implements an I2C arbitration scheme
where masters need to claim the bus with a GPIO before they can start
a transaction. This should generally only be used when standard I2C
multimaster isn't appropriate for some reason (errata/bugs).
This driver is based on code that Simon Glass added to the i2c-s3c2410
driver in the Chrome OS kernel 3.4 tree. The current incarnation as a
mux driver is as suggested by Grant Likely. See
<https://patchwork.kernel.org/patch/1877311/> for some history.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Use generic DMA DT helper. Platforms booting with or without DT populated are
both supported.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In PIO mode we can end up with the same errors as in DMA mode, but as IRQs
are disabled there we have to check for them manually after each command.
Also don't use the big controller reset hammer when receiving a NAK from a
slave. It's sufficient to tell the controller to continue at a clean state.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit fixes the three following races in PIO code:
- The CTRL0 register is racy in itself, when programming transfer state and
run bit in the same cycle the hardware sometimes ends up using the state
from the last transfer. Fix this by programming state in one cycle, make
sure the write is flushed down APBX bus by reading back the reg and only
then trigger the run bit.
- Only clear the DMAREQ bit in DEBUG0 after the read/write to the data reg
happened. Otherwise we are racing with the hardware about who touches
the data reg first.
- When checking for completion of a transfer it's not sufficient to check
if the data engine finished, but also a check for i2c bus idle is needed.
In PIO mode we are really fast to program the next transfer after a finished
one, so the controller possibly tries to start a new transfer while the
clkgen engine is still busy writing the NAK/STOP from the last transfer to
the bus.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using autosuspend helps to reduce the resume latency in situations where
another I2C message is going to be started soon. For example with HID over
I2C touch panels we get several messages in a short period of time while
the touch panel is in use.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is not an atomic context so there is no need to use mdelay() but
instead use usleep_range().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The correct way to disable or enable the controller is to wait until the
DW_IC_ENABLE_STATUS register bit matches the bit we program into DW_IC_ENABLE
register. This procedure is described in the DesignWare I2C databook.
By doing this we can be sure that the controller is in correct state once
the function returns.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is not good idea to mix static and dynamic I2C adapter numbering. In
this particular case on Lynxpoint we had graphics I2C adapter which took
the first numbers preventing the designware I2C driver from using the
adapter numbers it preferred.
Since Lynxpoint support was just introduced and there is no hardware available
outside Intel we can fix this by switching to use dynamic adapter numbering
instead of static.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With dev_err() we can get the device instance printed as well and is pretty
much standard to use dev_* macros in the drivers anyway. In addition
correct the indentation of probe() arguments.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller and tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
CONFIG_HOTPLUG is going away as an option, cleanup CONFIG_HOTPLUG
ifdefs in i2c files.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBus read and write are supported by the emulation layer of i2c
framework if the controller doesn't have SMBus features.
I2C_M_RECV_LEN flag is used to let i2c drivers know rx length is not
yet determined but will be read to the first byte in rx buffer.
s3c2410 doesn't handle this flag. So only one byte is read from slave.
There fore following two features are added to the driver code.
1. skip rx length check if I2C_M_RECV_LEN is set and the length is 1.
2. add actual bytes to the rx length after reading first bytes if
I2C_M_RECV_LEN.
I2C_M_RECV_LEN is only set for SMBus command. So this code does not
affect legacy codes which only use i2c command for s3c2410.
Signed-off-by: Jaemin Yoo <jmin.yoo@samsung.com>
Tested-by: Prasanna Kumar <prasanna.ps@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With the generic DMA device tree helper supported by mxs-dma driver,
client devices only need to call dma_request_slave_channel() for
requesting a DMA channel from dmaengine.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
The ACPI handle of struct i2c_adapter's dev member should not be
set, because this causes that struct i2c_adapter to be associated
with the ACPI device node corresponding to its parent as the
second "physical_device", which is incorrect (this happens during
the registration of struct i2c_adapter). Consequently,
acpi_i2c_register_devices() should use the ACPI handle of the
parent of the struct i2c_adapter it is called for rather than the
struct i2c_adapter's ACPI handle (which should be NULL).
Make that happen and modify the i2c-designware-platdrv driver,
which currently is the only driver for ACPI-enumerated I2C
controller chips, not to set the ACPI handle for the
struct i2c_adapter it creates.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
i2c_del_mux_adapter always returns 0 and none of it current users check its
return value anyway. It is also an essential requirement of the Linux device
driver model, that functions which may be called from a device's remove callback
to free resources provided by the device, are not allowed to fail. This is the
case for i2c_del_mux_adapter(), so make its return type void to make the
fact that it won't fail explicit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_del_mux_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore its return
value and assume that it will always succeed (which it will). A subsequent
patch will make the return type of i2c_del_mux_adapter() void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_del_adapter() is usually called from a drivers remove callback. The Linux
device driver model does not allow the remove callback to fail and all resources
allocated in the probe callback need to be freed, as well as all resources which
have been provided to the rest of the kernel(for example a I2C adapter) need to
be revoked. So any function revoking such resources isn't allowed to fail
either. i2c_del_adapter() adheres to this requirement and will never fail. But
i2c_del_adapter()'s return type is int, which may cause driver authors to think
that it can fail. This led to code constructs like:
ret = i2c_del_adapter(...);
BUG_ON(ret);
Since i2c_del_adapter() always returns 0 the BUG_ON is never hit and essentially
becomes dead code, which means it can be removed. Making the return type of
i2c_del_adapter() void makes it explicit that the function will never fail and
should prevent constructs like the above from re-appearing in the kernel code.
All callers of i2c_del_adapter() have already been updated in a previous patch
to ignore the return value, so the conversion of the return type from int to
void can be done without causing any build failures.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_del_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore the return
value and assume that it will always succeed (which it will). In a subsequent
patch the return type of i2c_del_adapter() will be made void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently i2c_del_adapter() returns -EINVAL when it gets an adapter which is not
registered. But none of the users of i2c_del_adapter() depend on this behavior,
so for the sake of being able to sanitize the return type of i2c_del_adapter
argue, that the purpose of i2c_del_adapter() is to remove an I2C adapter from
the system. If the adapter is not registered in the first place this becomes a
no-op. So we can return success without having to do anything.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The detach_adapter callback has been deprecated for quite some time and has no
user left. Keeping it alive blocks other cleanups, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the code to use devm_* API so that driver core will manage
resources.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since we have generic i2c bus recover routines now, these custom ones
need to be renamed to fix the namespace clash. Proper conversion needs
to be done by someone who has access to the hardware.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
gpio_direction_output() may fail, check for that and deal with it
appropriately. Also log an error message if gpio_request() fails.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
GPIOs may not be available immediately when i2c-gpio looks for them.
Implement support for deferred probing so that probing can be
attempted again later when GPIO pins are finally available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make them conform more to established standards.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The register definitions are only used in the driver itself.
This also removes the last dependency on plat/ includes from the
i2c driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Delete the header that defines it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit: "i2c-core: dt: Pick i2c bus number from i2c alias if
present" adds support for automatically picking the bus number based
on the alias ID. Remove the now unnecessary code from i2c-pxa that
did the same thing.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c bus recovery infrastructure to i2c adapters as specified in the i2c
protocol Rev. 03 section 3.1.16 titled "Bus clear".
http://www.nxp.com/documents/user_manual/UM10204.pdf
Sometimes during operation i2c bus hangs and we need to give dummy clocks to
slave device to start the transfer again. Now we may have capability in the bus
controller to generate these clocks or platform may have gpio pins which can be
toggled to generate dummy clocks. This patch supports both.
This patch also adds in generic bus recovery routines gpio or scl line based
which can be used by bus controller. In addition controller driver may provide
its own version of the bus recovery routine.
This doesn't support multi-master recovery for now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[wsa: changed gpio type to int and minor reformatting]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows you to get the equivalent functionality of
i2c_add_numbered_adapter() with all data in the device tree and no
special case code in your driver. This is a common device tree
technique.
For quick reference, the FDT syntax for using an alias to provide an
ID looks like:
aliases {
i2c0 = &i2c_0;
i2c1 = &i2c_1;
};
Signed-off-by: Doug Anderson <dianders@chromium.org>
[wsa: removed one check from static function. We know our callers]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c fixes from Wolfram Sang:
"One bugfix for the tegra driver. Two updates regarding email
addresses and MAINTAINERS which I like to have up-to-date so people
can be reached immediately. While we are here, there is on PCI_ID
addition."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer entry for atmel i2c driver
i2c: Fix my e-mail address in drivers and documentation
i2c: iSMT: add Intel Avoton DeviceIDs
i2c: tegra: check the clk_prepare_enable() return value
This patch adds the iSMT SMBus Controller DeviceIDs for the Intel Avoton SOC.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
NVIDIA's Tegra SoC allows read/write of controller register only
if controller clock is enabled. System hangs if read/write happens
to registers without enabling clock.
clk_prepare_enable() can be fail due to unknown reason and hence
adding check for return value of this function. If this function
success then only access register otherwise return to caller with
error.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Wolfram Sang