Impact: fix to enable APIC for AMD Fam10h on chipsets with a missing/b0rked
ACPI MP table (MADT)
Booting a 32bit kernel on an AMD Fam10h CPU running on chipsets with
missing/b0rked MP table leads to a hang pretty early in the boot process
due to the APIC not being initialized. Fix that by falling back to the
default APIC base address in 32bit code, as it is done in the 64bit
codepath.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Fixes dumpstack and KDB on 64 bits
This re-adds the old stack pointer to the top of the irqstack to help
with unwinding. It was removed in commit d99015b1ab
as part of the save_args out-of-line work.
Both dumpstack and KDB require this information.
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Eric Paris reported:
> I have an hp dl785g5 which is unable to successfully run
> 2.6.29-0.66.rc3.fc11.x86_64 or 2.6.29-rc2-next-20090126. During bootup
> (early in userspace daemons starting) I get the below BUG, which quickly
> renders the machine dead. I assume it is because sparse_irq_lock never
> gets released when the BUG kills that task.
Adjust lock sequence when migrating a descriptor with
CONFIG_NUMA_MIGRATE_IRQ_DESC enabled.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, ds, bts: cleanup/fix DS configuration
ring-buffer: reset timestamps when ring buffer is reset
trace: set max latency variable to zero on default
trace: stop all recording to ring buffer on ftrace_dump
trace: print ftrace_dump at KERN_EMERG log level
ring_buffer: reset write when reserve buffer fail
tracing/function-graph-tracer: fix a regression while suspend to disk
ring-buffer: fix alignment problem
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 setup: fix asm constraints in vesa_store_edid
xen: make sysfs files behave as their names suggest
x86: tone down mtrr_trim_uncached_memory() warning
x86: correct the CPUID pattern for MSR_IA32_MISC_ENABLE availability
[
mingo@elte.hu: these fixes are a subset of changes cherry-picked from:
git://git.kernel.org:/pub/scm/linux/kernel/git/jejb/voyager-2.6.git
They fix various problems that recent x86 changes caused in the Voyager
subarchitecture: both APIC changes and cpumask changes and certain
cleanups caused subarch assumptions to break.
Most of these changes are obsolete as the subarch code has been removed
from the x86 development tree - but we merge them upstream to make Voyager
build and boot.
]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move DMA-mapping.txt to Documentation/PCI/.
DMA-mapping.txt was supposed to be moved from Documentation/ to
Documentation/PCI/. The 00-INDEX files in those two directories
were updated, along with a few other text files, but the file
itself somehow escaped being moved, so move it and update more
text files and source files with its new location.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kerneloops.org is reporting a lot of these warnings that come due to
vmware not setting up any MTRRs for emulated CPUs:
| Reported 709 times (14696 total reports)
| BIOS bug (often in VMWare) where the MTRR's are set up incorrectly
| or not at all
|
| This warning was last seen in version 2.6.29-rc2-git1, and first
| seen in 2.6.24.
|
| More info:
| http://www.kerneloops.org/searchweek.php?search=mtrr_trim_uncached_memory
Keep a one-liner KERN_INFO about it - so that we have so notice if empty
MTRRs are caused by native hardware/BIOS weirdness.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debugobjects: add and use INIT_WORK_ON_STACK
rcu: remove duplicate CONFIG_RCU_CPU_STALL_DETECTOR
relay: fix lock imbalance in relay_late_setup_files
oprofile: fix uninitialized use of struct op_entry
rcu: move Kconfig menu
softlock: fix false panic which can occur if softlockup_thresh is reduced
rcu: add __cpuinit to rcu_init_percpu_data()
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimers: fix inconsistent lock state on resume in hres_timers_resume
time-sched.c: tick_nohz_update_jiffies should be static
locking, hpet: annotate false positive warning
kernel/fork.c: unused variable 'ret'
itimers: remove the per-cpu-ish-ness
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (29 commits)
xen: unitialised return value in xenbus_write_transaction
x86: fix section mismatch warning
x86: unmask CPUID levels on Intel CPUs, fix
x86: work around PAGE_KERNEL_WC not getting WC in iomap_atomic_prot_pfn.
x86: use standard PIT frequency
xen: handle highmem pages correctly when shrinking a domain
x86, mm: fix pte_free()
xen: actually release memory when shrinking domain
x86: unmask CPUID levels on Intel CPUs
x86: add MSR_IA32_MISC_ENABLE bits to <asm/msr-index.h>
x86: fix PTE corruption issue while mapping RAM using /dev/mem
x86: mtrr fix debug boot parameter
x86: fix page attribute corruption with cpa()
Revert "x86: signal: change type of paramter for sys_rt_sigreturn()"
x86: use early clobbers in usercopy*.c
x86: remove kernel_physical_mapping_init() from init section
fix: crash: IP: __bitmap_intersects+0x48/0x73
cpufreq: use work_on_cpu in acpi-cpufreq.c for drv_read and drv_write
work_on_cpu: Use our own workqueue.
work_on_cpu: don't try to get_online_cpus() in work_on_cpu.
...
Impact: re-enable CPUID unmasking on affected processors
As far as I am capable of discerning from the documentation,
MSR_IA32_MISC_ENABLE should be available for all family 0xf CPUs, as
well as family 6 for model >= 0xd (newer Pentium M).
The documentation on this isn't ideal, so we need to be on the lookout
for errors, still.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Here function vmi_activate calls a init function activate_vmi , which
causes the following section mismatch warnings:
LD arch/x86/kernel/built-in.o
WARNING: arch/x86/kernel/built-in.o(.text+0x13ba9): Section mismatch
in reference from the function vmi_activate() to the function
.init.text:vmi_time_init()
The function vmi_activate() references
the function __init vmi_time_init().
This is often because vmi_activate lacks a __init
annotation or the annotation of vmi_time_init is wrong.
WARNING: arch/x86/kernel/built-in.o(.text+0x13bd1): Section mismatch
in reference from the function vmi_activate() to the function
.devinit.text:vmi_time_bsp_init()
The function vmi_activate() references
the function __devinit vmi_time_bsp_init().
This is often because vmi_activate lacks a __devinit
annotation or the annotation of vmi_time_bsp_init is wrong.
WARNING: arch/x86/kernel/built-in.o(.text+0x13bdb): Section mismatch
in reference from the function vmi_activate() to the function
.devinit.text:vmi_time_ap_init()
The function vmi_activate() references
the function __devinit vmi_time_ap_init().
This is often because vmi_activate lacks a __devinit
annotation or the annotation of vmi_time_ap_init is wrong.
Fix it by marking vmi_activate() as __init too.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix boot hang on pre-model-15 Intel CPUs
rdmsrl_safe() does not work in very early bootup code yet, because we
dont have the pagefault handler installed yet so exception section
does not get parsed. rdmsr_safe() will just crash and hang the bootup.
So limit the MSR_IA32_MISC_ENABLE MSR read to those CPU types that
support it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cleanup the cpuid check for DS configuration.
This also fixes a Corei7 CPUID enumeration bug.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Fix debugobjects warning
debugobject enabled kernels spit out a warning in hpet code due to a
workqueue which is initialized on stack.
Add INIT_WORK_ON_STACK() which calls init_timer_on_stack() and use it
in hpet.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: Fixes crashes with misconfigured BIOSes on XSAVE hardware
Avuton Olrich reported early boot crashes with v2.6.28 and
bisected it down to dc1e35c6e9
("x86, xsave: enable xsave/xrstor on cpus with xsave support").
If the CPUID limit bit in MSR_IA32_MISC_ENABLE is set, clear it to
make all CPUID information available. This is required for some
features to work, in particular XSAVE.
Reported-and-bisected-by: Avuton Olrich <avuton@gmail.com>
Tested-by: Avuton Olrich <avuton@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
while looking at:
http://bugzilla.kernel.org/show_bug.cgi?id=11541
I realized that the mtrr.show param cannot work, because
the code is processed much too early.
This patch:
- Declares mtrr.show as early_param
- Stays consistent with the previous param (which I doubt
that it ever worked), so mtrr.show=1 would still work
- Declares mtrr_show as initdata
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 4217458daf.
Justin Madru bisected this commit, it was causing weird Firefox
crashes.
The reason is that GCC mis-optimizes (re-uses) the on-stack parameters of
the calling frame, which corrupts the syscall return pt_regs state and
thus corrupts user-space register state.
So we go back to the slightly less clean but more optimization-safe
method of getting to pt_regs. Also add a comment to explain this.
Resolves: http://bugzilla.kernel.org/show_bug.cgi?id=12505
Reported-and-bisected-by: Justin Madru <jdm64@gawab.com>
Tested-by: Justin Madru <jdm64@gawab.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
-tip testing found this crash:
> [ 35.258515] calling acpi_cpufreq_init+0x0/0x127 @ 1
> [ 35.264127] BUG: unable to handle kernel NULL pointer dereference at (null)
> [ 35.267554] IP: [<ffffffff80478092>] __bitmap_intersects+0x48/0x73
> [ 35.267554] PGD 0
> [ 35.267554] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
arch/x86/kernel/cpu/cpufreq/acpi-cpufreq.c is still broken: there's no
allocation of the variable mask, so we pass in an uninitialized cmd.mask
field to drv_read(), which then passes it to the scheduler which then
crashes ...
Switch it over to the much simpler constant-cpumask-pointers approach.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: use new work_on_cpu function to reduce stack usage
Replace the saving of current->cpus_allowed and set_cpus_allowed_ptr() with
a work_on_cpu function for drv_read() and drv_write().
Basically converts do_drv_{read,write} into "work_on_cpu" functions that
are now called by drv_read and drv_write.
Note: This patch basically reverts 50c668d6 which reverted 7503bfba, now
that the work_on_cpu() function is more stable.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Dieter Ries <clip2@gmx.de>
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Cc: <cpufreq@vger.kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The function setup_cpu_local_masks() has been marked __init, in
order to remove the following section mismatch messages:
WARNING: vmlinux.o(.text+0x3c2c7): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.
WARNING: vmlinux.o(.text+0x3c2d3): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.
WARNING: vmlinux.o(.text+0x3c2df): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.
WARNING: vmlinux.o(.text+0x3c2eb): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add debug warning
Fire off one message if two apic's discovered with different
apic versions. (this code is only called during CPU init)
The goal of this is to pave the way of the removal of the apic_version[]
array. We dont expect any apic version incompatibilities in the x86
landscape of systems [if so we dont handle them very well and probably
never will handle deep apic version assymetries well], but it's prudent
to have a debug check for one kernel cycle nevertheless.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Check CONFIG_FREEZER instead of CONFIG_PM because kprobe booster
depends on freeze_processes() and thaw_processes() when CONFIG_PREEMPT=y.
This fixes a linkage error which occurs when CONFIG_PREEMPT=y, CONFIG_PM=y
and CONFIG_FREEZER=n.
Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Len Brown <len.brown@intel.com>
The function uv_wait_completion() spins on reads of a memory-mapped
register, waiting for completion of BAU hardware replies.
It should call "cpu_relax()" between those reads to improve performance
on hyperthreaded configurations.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix potential boot crash on MAXSMP
Remove code left over by:
50c668d: Revert "cpumask: use work_on_cpu in acpi-cpufreq.c for drv_read
That cmd.cpumask is not allocated anymore. No impact on default !MAXSMP
kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit e0c7317557.
This patch was wrong, as lockdep (and thus the irq state tracer)
aren't nmi safe. People are already seeing lockdep warnings due
to this.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 7503bfbae8.
Dieter Ries reported bootup soft-hangs and bisected it back to
this commit, and reverting this commit gave him a working system.
The commit introduces work_on_cpu() use into the cpufreq code,
but that is subtly problematic from a lock hierarchy POV: the
hotplug-cpu lock is an highlevel lock that is taken before
lowlevel locks, and in this codepath we are called with the
policy lock taken.
Dieter did not have lockdep enabled so we dont have a nice stack
trace proof for this, but using work_on_cpu() in such a lowlevel
place certainly looks wrong, so we revert the patch.
work_on_cpu() needs to be reworked to be more generally usable.
Reported-by: Dieter Ries <clip2@gmx.de>
Tested-by: Dieter Ries <clip2@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix this by reintroducing asm/smp.h include in apic.c - later on
I will fix this by removing non-smp data from smp.h
Also fix the __inquire_remote_apic() prototype/inline.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix this by reintroducing asm/smp.h include in mpparse.c - later on
I will fix this by removing non-smp data from smp.h.
Reported-by: Petr Titera <P.Titera@century.cz>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Alexander Beregalov reported that this warning is caused by the HPET code:
> hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
> hpet0: 3 comparators, 64-bit 14.318180 MHz counter
> ODEBUG: object is on stack, but not annotated
> ------------[ cut here ]------------
> WARNING: at lib/debugobjects.c:251 __debug_object_init+0x2a4/0x352()
> Bisected down to 26afe5f2fb
> (x86: HPET_MSI Initialise per-cpu HPET timers)
The commit is fine - but the on-stack workqueue entry needs annotation.
Reported-and-bisected-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
x86: fix section mismatch warnings in mcheck/mce_amd_64.c
x86: offer frame pointers in all build modes
x86: remove duplicated #include's
x86: k8 numa register active regions later
x86: update Alan Cox's email addresses
x86: rename all fields of mpc_table mpc_X to X
x86: rename all fields of mpc_oemtable oem_X to X
x86: rename all fields of mpc_bus mpc_X to X
x86: rename all fields of mpc_cpu mpc_X to X
x86: rename all fields of mpc_intsrc mpc_X to X
x86: rename all fields of mpc_lintsrc mpc_X to X
x86: rename all fields of mpc_iopic mpc_X to X
x86: irqinit_64.c init_ISA_irqs should be static
Documentation/x86/boot.txt: payload length was changed to payload_length
x86: setup_percpu.c fix style problems
x86: irqinit_64.c fix style problems
x86: irqinit_32.c fix style problems
x86: i8259.c fix style problems
x86: irq_32.c fix style problems
x86: ioport.c fix style problems
...
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
[IA64] fix typo in cpumask_of_pcibus()
x86: fix x86_32 builds for summit and es7000 arch's
cpumask: use work_on_cpu in acpi-cpufreq.c for read_measured_perf_ctrs
cpumask: use work_on_cpu in acpi-cpufreq.c for drv_read and drv_write
cpumask: use cpumask_var_t in acpi-cpufreq.c
cpumask: use work_on_cpu in acpi/cstate.c
cpumask: convert struct cpufreq_policy to cpumask_var_t
cpumask: replace CPUMASK_ALLOC etc with cpumask_var_t
x86: cleanup remaining cpumask_t ops in smpboot code
cpumask: update pci_bus_show_cpuaffinity to use new cpumask API
cpumask: update local_cpus_show to use new cpumask API
ia64: cpumask fix for is_affinity_mask_valid()
We found a situation on Linus' machine that the Nvidia timer quirk hit on
a Intel chipset system. The problem is that the system has a fancy Nvidia
card with an own PCI bridge, and the early-quirks code looking for any
NVidia bridge triggered on it incorrectly. This didn't lead a boot
failure by luck, but the timer routing code selecting the wrong timer
first and some ugly messages. It might lead to real problems on other
systems.
I checked all the devices which are currently checked for by early_quirks
and it turns out they are all located in the root bus zero.
So change the early-quirks loop to only scan bus 0. This incidently also
saves quite some unnecessary scanning work, because early_quirks doesn't
go through all the non root busses.
The graphics card is not on bus 0, so it is not matched anymore.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some boxes there exist both RSDT and XSDT table. But unfortunately
sometimes there exists the following error when XSDT table is used:
a. 32/64X address mismatch
b. The 32/64X FACS address mismatch
In such case the boot option of "acpi=rsdt" is provided so that
RSDT is tried instead of XSDT table when the system can't work well.
http://bugzilla.kernel.org/show_bug.cgi?id=8246
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
cc:Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
The Cx Register address obtained from the _CST object is used as the MWAIT
hints if the register type is FFixedHW. And it is used to check whether
the Cx type is supported or not.
On some boxes the following Cx state package is obtained from _CST object:
>{
ResourceTemplate ()
{
Register (FFixedHW,
0x01, // Bit Width
0x02, // Bit Offset
0x0000000000889759, // Address
0x03, // Access Size
)
},
0x03,
0xF5,
0x015E }
In such case we should use the bit[7:4] of Cx address to check whether
the Cx type is supported or not.
mask the MWAIT hint to avoid array address overflow
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by:Venki Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Mark the function local_allocate_threshold_blocks() with __cpuinit,
in order to remove the following section mismatch messages:
WARNING: arch/x86/kernel/cpu/mcheck/built-in.o(.text+0x1363): Section mismatch in reference from the function local_allocate_threshold_blocks() to the function .cpuinit.text:allocate_threshold_blocks()
The function local_allocate_threshold_blocks() references
the function __cpuinit allocate_threshold_blocks().
This is often because local_allocate_threshold_blocks lacks a __cpuinit
annotation or the annotation of allocate_threshold_blocks is wrong.
WARNING: arch/x86/kernel/cpu/built-in.o(.text+0x1def): Section mismatch in reference from the function local_allocate_threshold_blocks() to the function .cpuinit.text:allocate_threshold_blocks()
The function local_allocate_threshold_blocks() references
the function __cpuinit allocate_threshold_blocks().
This is often because local_allocate_threshold_blocks lacks a __cpuinit
annotation or the annotation of allocate_threshold_blocks is wrong.
WARNING: arch/x86/kernel/built-in.o(.text+0xef2b): Section mismatch in reference from the function local_allocate_threshold_blocks() to the function .cpuinit.text:allocate_threshold_blocks()
The function local_allocate_threshold_blocks() references
the function __cpuinit allocate_threshold_blocks().
This is often because local_allocate_threshold_blocks lacks a __cpuinit
annotation or the annotation of allocate_threshold_blocks is wrong.
All the callsites of this function are __cpuinit already, and all the
functions it calls are __cpuinit as well.
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: fix rcutorture bug
rcu: eliminate synchronize_rcu_xxx macro
rcu: make treercu safe for suspend and resume
rcu: fix rcutree grace-period-latency bug on small systems
futex: catch certain assymetric (get|put)_futex_key calls
futex: make futex_(get|put)_key() calls symmetric
locking, percpu counters: introduce separate lock classes
swiotlb: clean up EXPORT_SYMBOL usage
swiotlb: remove unnecessary declaration
swiotlb: replace architecture-specific swiotlb.h with linux/swiotlb.h
swiotlb: add support for systems with highmem
swiotlb: store phys address in io_tlb_orig_addr array
swiotlb: add hwdev to swiotlb_phys_to_bus() / swiotlb_sg_to_bus()
Ingo Molnar