Drop CONFIG_I2C_BOARDINFO ifdefs as the common i2c header handles this
already by stubbing things out
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Avoid conditional branch instructions during carry bit additions.
Special thanks to Bernd.
Simplify: Use ((len + proto) << 8) like every other __LITTLE_ENDIAN__ machine
Cc: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Mike Frysinger <vapier.adi@gmail.com>:
- setup P_DEFAULT_BOOT_SPI_CS for every arch based on
the default bootrom behavior and convert all our boards
to it
- revert previous anomaly change ... bf51x is not affected
by anomaly 05000353]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
merge more of the bf54x and !bf54x gpio code together to
cut down on #ifdef mess
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This patch changes the gpio_free implementations for the blackfin
architecture.
Signed-off-by: Uwe Kleine-Koenig <ukleinek@strlen.de>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make sure we don't accidently re-enable interrupts if we are being
called in atomic context
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
when requesting a GPIO for the first time, the POLAR setting is not
set to a sane state. this can lead to indeterminate behavior that
cannot be resolved without an explicit write to the Blackfin port POLAR
register.
when requesting a GPIO for the first time via gpio_request(), the POLAR
setting for the GPIO in question should be set to sane state. this
should occur if the GPIO has not been allocated in any other way.
some examples:
- when doing something like "request_irq(); gpio_request();" on the
same GPIO, the POLAR setting should not be reset.
- when doing "gpio_request(); gpio_request();" on the same GPIO, the
POLAR setting should be reset only the first time and not the second.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
On BF561 EBIU_SDGCTL bit 31 controls the SDRAM external data
path width, typically set 0 for a 32-bit bus width. On other
Blackfin derivatives this bit should be set by default.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Dmacopy failed in BF537-STAMP when copy from SRAM to SDRAM and kernel
will reboot automatically.
Fixing by doing a SSYNC before mucking with DMA registers
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
They were long enough set deprecated...
Update Documentation/cpu-freq/users-guide.txt:
The deprecated files listed there seen not to exist for some time anymore
already.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: fix to enable APIC for AMD Fam10h on chipsets with a missing/b0rked
ACPI MP table (MADT)
Booting a 32bit kernel on an AMD Fam10h CPU running on chipsets with
missing/b0rked MP table leads to a hang pretty early in the boot process
due to the APIC not being initialized. Fix that by falling back to the
default APIC base address in 32bit code, as it is done in the 64bit
codepath.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Fix race condition
xen_mc_batch has a small preempt race where it takes the address of a
percpu variable immediately before disabling interrupts, thereby
leaving a small window in which we may migrate to another cpu and save
the flags in the wrong percpu variable. Disable interrupts before
saving the old flags in a percpu.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This builds upon eeabac7386
("sparc64: Validate kernel generated fault addresses on sparc64.")
Upon further consideration, we actually should never see any
fault addresses for 32-bit tasks with the upper 32-bits set.
If it does every happen, by definition it's a bug. Whatever
context created that fault would only have that fault satisfied
if we used the full 64-bit address. If we truncate it, we'll
always fault the wrong address and we'll always loop faulting
forever.
So catch such conditions and mark them as errors always. Log
the error and fail the fault.
Signed-off-by: David S. Miller <davem@davemloft.net>
Trim out obsolete/extraneous properties and tighten up some usage
conventions. Changes include:
- removal of device_type properties
- removal of cell-index properties
- Addition of gpio-controller and #gpio-cells properties to gpio
nodes
- Move common interrupt-parent property out of device nodes and
into top level parent node.
This patch also include what looks to be just trivial editorial
whitespace/format changes, but there is real method in this
madness. Editorial changes were made to keep the all the
mpc5200 board device trees as similar as possible so that diffs
between them only show the real differences between the boards.
The pcm030 device tree was most affected by this because many
of the comments had been changed from // to /* */ style and
some cell values where changed from decimal to hex format when
it was cloned from one of the other 5200 device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
In order to handle all of the cases of address calculation overflow
properly, we run sparc 32-bit processes in "address masking" mode
when running on a 64-bit kernel.
Address masking mode zeros out the top 32-bits of the address
calculated for every load and store instruction.
However, when we're in privileged mode we have to run with that
address masking mode disabled even when accessing userspace from
the kernel.
To "simulate" the address masking mode we clear the top-bits by
hand for 32-bit processes in the fault handler.
It is the responsibility of code in the compat layer to properly
zero extend addresses used to access userspace. If this isn't
followed properly we can get into a fault loop.
Say that the user address is 0xf0000000 but for whatever reason
the kernel code sign extends this to 64-bit, and then the kernel
tries to access the result.
In such a case we'll fault on address 0xfffffffff0000000 but the fault
handler will process that fault as if it were to address 0xf0000000.
We'll loop faulting forever because the fault never gets satisfied.
So add a check specifically for this case, when the kernel is faulting
on a user address access and the addresses don't match up.
This code path is sufficiently slow path, and this bug is sufficiently
painful to diagnose, that this kind of bug check is warranted.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we're idling in NOHZ mode, timer interrupts are not running.
Evidence of processing timer interrupts is what the NMI watchdog
uses to determine if the CPU is stuck.
On Niagara, we'll yield the cpu. This will make the cpu, at
worst, hang out in the hypervisor until an interrupt arrives.
This will prevent the NMI watchdog timer from firing.
However on non-Niagara we just loop executing instructions
which will cause the NMI watchdog to keep firing. It won't
see timer interrupts happening so it will think the cpu is
stuck.
Fix this by touching the NMI watchdog in the cpu idle loop
on non-Niagara machines.
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Fixes dumpstack and KDB on 64 bits
This re-adds the old stack pointer to the top of the irqstack to help
with unwinding. It was removed in commit d99015b1ab
as part of the save_args out-of-line work.
Both dumpstack and KDB require this information.
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: Change link order of pciehp & acpiphp
PCI hotplug: fakephp: Allocate PCI resources before adding the device
PCI MSI: Fix undefined shift by 32
PCI PM: Do not wait for buses in B2 or B3 during resume
PCI PM: Power up devices before restoring their state
PCI PM: Fix hibernation breakage on EeePC 701
PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
PCI PM: Fix suspend error paths and testing facility breakage
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
powerpc: Fix oops on some machines due to incorrect pr_debug()
powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
powerpc/5200: update device tree binding documentation
powerpc/5200: Bugfix for PCI mapping of memory and IMMR
powerpc/5200: update defconfigs
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Automatic I2C device probing is not done any more. Therefore we need
proper DTS device node definitions for the I2C LM75 thermal sensor on
the TQM85xx modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Recently, a patch left DEBUG enabled in the powerpc common PCI code,
resulting in an old bug in a pr_debug() statement to show up and cause
a NULL dereference on some machines.
This fixes the pr_debug() statement and reverts to DEBUG not being
force-enabled in that file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Eric Paris reported:
> I have an hp dl785g5 which is unable to successfully run
> 2.6.29-0.66.rc3.fc11.x86_64 or 2.6.29-rc2-next-20090126. During bootup
> (early in userspace daemons starting) I get the below BUG, which quickly
> renders the machine dead. I assume it is because sparse_irq_lock never
> gets released when the BUG kills that task.
Adjust lock sequence when migrating a descriptor with
CONFIG_NUMA_MIGRATE_IRQ_DESC enabled.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, ds, bts: cleanup/fix DS configuration
ring-buffer: reset timestamps when ring buffer is reset
trace: set max latency variable to zero on default
trace: stop all recording to ring buffer on ftrace_dump
trace: print ftrace_dump at KERN_EMERG log level
ring_buffer: reset write when reserve buffer fail
tracing/function-graph-tracer: fix a regression while suspend to disk
ring-buffer: fix alignment problem
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 setup: fix asm constraints in vesa_store_edid
xen: make sysfs files behave as their names suggest
x86: tone down mtrr_trim_uncached_memory() warning
x86: correct the CPUID pattern for MSR_IA32_MISC_ENABLE availability
[
mingo@elte.hu: these fixes are a subset of changes cherry-picked from:
git://git.kernel.org:/pub/scm/linux/kernel/git/jejb/voyager-2.6.git
They fix various problems that recent x86 changes caused in the Voyager
subarchitecture: both APIC changes and cpumask changes and certain
cleanups caused subarch assumptions to break.
Most of these changes are obsolete as the subarch code has been removed
from the x86 development tree - but we merge them upstream to make Voyager
build and boot.
]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"flash" is a very generic name for a platform_driver that is only
available on SA11x0.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Pitre <nico@marvell.com>
SPIN_LOCK_UNLOCKED is deprecated as lockdep cannot properly work with
locks initialized with it.
This fix is necessary to compile the linux-rt tree for ARM.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Steven Rostedt <srostedt@redhat.com>
Impact: fix potential miscompile (currently believed non-manifest)
As the comment explains, the VBE DDC call can clobber any register.
Tell the compiler about that fact.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In Linus' current -git the cpumask member is now a pointer.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This kernel symbol provides a way for drivers to switch on alternate
function for a certain GPIO pin. Turning it off is done implicitly when
changing the GPIO direction, as that would be fixed when using the given
pin als alternate function.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the {set,get}_434_reg() prototypes, as the functions have been
removed. Also move the prototypes for {get,set}_latch_u5() to the correct
place.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As rb532_dev3_ctl_res is not used by any platform device, it can be dropped
when not used for holding the physical address of the device 3 controller.
Also a size of one byte should suffice when ioremapping the physical
address mentioned above, as only a single byte is being read from and
written to it.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These kernel symbols are unused. Also, since dev3 init has been moved to
devices.c, set_434_reg() breaks compiling as it uses dev3.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This code doesn't belong to gpio.c, as it's completely unrelated to
GPIO. As dev1 and dev2 init code is in devices.c, it seems to be a more
adequate place.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The data to be written is just a byte, so use writeb instead of writel.
Also, dev3.base contains the address, not the data so referencing here
is wrong.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This register just contains the address of the actual resource, so
initialisation has to be the same as cf_slot0_res and nand_slot0_res.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As the korina ethernet driver uses platform_get_drvdata() to extract the
driver specific data from the platform device, driver_data has to be
used here.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Auto-detection works just fine, so use it instead of specifying the type
manually. Also define a platform device for the uart, as suggested by
David Daney.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As the pata-rb532-cf driver calls gpio_direction_input(), the calls to
rb532_gpio_set_func() and rb532_gpio_direction_input() are not needed since
the alternate function is automatically being disabled when changing the
GPIO pin direction.
The later two calls to rb532_gpio_set_{ilevel,istat}() are implicitly being
done by the IRQ initialisation of pata-rb532-cf.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When a driver calls gpio_set_direction_{input,output}(), it obviously
doesn't want the alternate function for that pin to be active (as the
direction would not matter in that case). This patch ensures alternate
function is disabled when the direction is being changed.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Interrupt Group 4 mapps the GPIO pins enabled as interrupt sources;
add defines to make this clear when addressing them later in code.
The mapped GPIOs support triggering on either level high or low. To
achieve this, the set_type() function calls rb532_gpio_set_ilevel() for
interrupts of the above mentioned group.
As there is no way to alter the triggering characteristics of the other
interrupts, accept level triggering on status high only. (This is just a
guess; but as the system boots fine and interrupt-driven devices (e.g.
serial console) work with no implications, it seems to be right.)
To clear a GPIO mapped IRQ, the source has to be cleared (i.e., the
interrupt status bit of the corresponding GPIO pin). This is done inside
rb532_disable_irq().
After applying these changes I could undo most of my former "fixes" to
pata-rb532-cf. Particularly all interrupt handling can be done
generically via set_irq_type() as it was before.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code is rather based on trial-and-error than knowledge. Verified Via
Rhine functionality in PIO as well as MMIO mode.
[Looks sane -- Ralf]
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The algorithm works unconditionally. If bitval is one, the first line is
a no op and the second line sets the bit at offset position. Vice versa,
if bitval is zero, the first line clears the bit at offset position and
the second line is a no op.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The previous definition inadvertently omits Octeon which currently is
treated as an architecture variant separate from MIPS32 and MIPS64.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If a context switch occurred between the watch exception and reading the
watch registers, it would be possible for the new process to corrupt their
state. Enabling interrupts only after the watch registers are read avoids
this race.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes the ptrace ABI for watch registers, and should allow 64bit
kernels to use the watch register support.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The special IP27 DMA code selected by DMA_IP27 has been removed a while
ago turning DMA_IP27 into almost a nop. Also fixup the broken logic of
its last users memcpy.S and memcpy-inatomic.s.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This shaves of 1912 bytes of an IP27 defconfig kernel and avoids
unexpected overflow behaviour in atomic_sub_if_positive. Apply the same
changes to the atomic64_* functions for consistency.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
fix the following 'make headers_check' warnings:
usr/include/asm/swab.h:4: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm/swab.h:7: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm/sigcontext32.h:20: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm/sigcontext.h:5: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm/sigcontext.h:24: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm/ptrace-abi.h:86: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm/ptrace-abi.h:93: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm/mtrr.h:61: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm/mce.h:7: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm/mce.h:29: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm/kvm.h:9: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm/kvm.h:16: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm/e820.h:44: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Move DMA-mapping.txt to Documentation/PCI/.
DMA-mapping.txt was supposed to be moved from Documentation/ to
Documentation/PCI/. The 00-INDEX files in those two directories
were updated, along with a few other text files, but the file
itself somehow escaped being moved, so move it and update more
text files and source files with its new location.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: Fix a memory leak with the lg object during launcher close
lguest: disable the FORTIFY for lguest.
lguest: typos fix
The commit "alpha: teach the compiler that BUG doesn't return"
(ed6b9b97f4) moved the asm code into inline
function which takes __FILE__ and __LINE__ as arguments. This violates
asm constrains there ("i" - an immediate operand with constant value), so
that compile may result in warning or error, depending on compiler
version.
Just adding an infinite loop to the BUG() is sufficient.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- jensen build: fix conflicting declarations for pci_alloc_consistent()
and undefined virt_to_phys();
- SMP: arch/alpha/kernel/smp.c:124: warning: passing argument 2
of '__cpu_test_and_set' discards qualifiers from pointer target type
Interestingly, this only happens with gcc-4.2; gcc <= 4.1 and gcc-4.3
are OK. Fixed with extra assignment.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch ensures that memory gets properly mapped into the PCI
address space. Without this patch, the memory window BAR is left
at whatever value happened to be loaded into the BAR when Linux
was booted. Without this patch, memory could end up getting mapped
at any of the 1G address boundaries instead of at '0' where Linux
expects it.
Similarly, this patch also ensures that the internally memory mapped
registers (IMMR) are mapped to the correct PCI address range.
Without this patch, PCI appears to work correctly until a PCI
device is inserted which DMAs into memory.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
In omap24xx_cpu_suspend assembly routine, the r2 register which holds
the address of the SDRC_POWER reg is set to zero before the value is
written back triggering a fault due to writing to address zero.
It's hard to tell where this change was introduced since this file
has been moved and merged.
While this fix prevents a crash, suspend on my n810 is broken with
current kernels. I never come out of suspend.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By Ingo Molnar, interrupts are not masked by default.
(refer to 76d2160147)
But if interrupts are not masked, the processor can wake up while in
Suspend-to-RAM state by an external interrupt. For example, if an
OMAP3 board is connected to Host PC by USB and entered to Suspend-to-RAM
state, it wake up automatically by M_IRQ_92. The disable_irq() function
can't disable the interrupt in H/W level, So I modified
arch/arm/mach-omap2/irq.c
Signed-off-by: Kim Kyuwon <chammoru@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When 32 kHz timer is used the min_delta_ns should be initialized so
that it reflects the timer programming cost. A write to the timer
device will be usually posted, but it takes roughly 3 cycles before
it is effective. If the timer is reprogrammed before that, the CPU
will stall until the previous write completes. This was pointed out by
Richard Woodruff.
Since the lower bound for min_delta_ns is 1000, the change is visible
only with tick rates less than 3 MHz.
Also note that the old value is incorrect for 32 kHz also due to
a rounding error, and it can cause the timer queue to hang (due to
clockevent code trying to program the timer with zero ticks).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Reviewed-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The naming accidentally broke while changing the name for the
driver to not to conflict with the other mmc driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This has similar symptoms than 66c23551b1
where just omap_request_dma, omap_dma_link_lch and omap_dma_unlink_lch
can cause incorrect dump_stack(). Here it can happen if channel has been
used before and the channel flags variable holds old status.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CSR must be cleared before invoking the callback.
If the callback function starts a new, fast DMA transfer on the same
channel, the completion status might lost if CSR is cleared after
the callback invocation.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A spin_lock deadlock will occur when omap_mcbsp_request() is invoked.
omap_mcbsp_request()
\- clk_enable(mcbsp->clk) [takes and holds clockfw_lock]
\- omap2_clk_enable()
\- _omap2_clk_enable()
\- omap_mcbsp_clk_enable()
\- clk_enable(child clock) [tries for clockfw_lock again]
mcbsp_clk is a virtual clock and it comprises several child clocks. when
enable mcbsp_clk in omap_mcbsp_request(), the enable function of mcbsp_clk
will enable its child clocks, then the deadlock occurs.
The solution is to remove the virtual clock and enable these child clocks in
omap_mcbsp_request() directly.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
kerneloops.org is reporting a lot of these warnings that come due to
vmware not setting up any MTRRs for emulated CPUs:
| Reported 709 times (14696 total reports)
| BIOS bug (often in VMWare) where the MTRR's are set up incorrectly
| or not at all
|
| This warning was last seen in version 2.6.29-rc2-git1, and first
| seen in 2.6.24.
|
| More info:
| http://www.kerneloops.org/searchweek.php?search=mtrr_trim_uncached_memory
Keep a one-liner KERN_INFO about it - so that we have so notice if empty
MTRRs are caused by native hardware/BIOS weirdness.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds basic support for the 6 GPIO lines found on GE Fanucs SBC310 to the GE Fanuc GPIO driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the default config file for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This corrects a deadlock encountered on ap325 in the cases where the
mutex is contended and the slow-path needs to be fallen back upon.
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The T-bit manipulation for syscall error checking had the side effect of
spuriously returning ERESTART* errno values over EINTR. So, we simplify
the error checking a bit and leave the T-bit alone.
Reported-by: Kaz Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes a bug in the FPU exception handler for the FCNVDS instruction.
To get the register number the instruction is shifted right by 9,
though it should be shifted right by 8.
More information at ST Linux bugzilla:
https://bugzilla.stlinux.com/show_bug.cgi?id=4892
Signed-off-by: Giuseppe Di Giore <giuseppe.di-giore@st.com>
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In rare circumstances csum_partial() can be called with data which is
not 16 or 32 bit aligned. This is been observed with RPC calls for NFS
file systems for example. Add support for handling this without resorting
to the misaligned fixup code (which is why this hasn't been seen as a
problem). This mimics the i386 version, which has had this support for
some time.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the ap325 defconfig to include
ov772x camera driver.
Old camera is still supported.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch add ov772x camera settings to ap325,
Old camera is still supported. And it will be 2nd camera
if you select ov772x and soc_camera_platform in same time.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the Migo-R defconfig to include
ov772x camera and tw9910 video driver
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It all lives in the oprofile support code currently and we will need
to share this stuff with NMI watchdog and perf_counter support.
Signed-off-by: David S. Miller <davem@davemloft.net>
The FSL PCI code depends on PCI quirks being enabled to function
properly. We can ensure this by doing a select in Kconfig of
PCI_QUIRKS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Instead of rounding the divider down, improve the baud-rate generators
accuracy by rounding to the nearest integer.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On booke processors, the code that maps low memory only uses up to three
CAM entries, even though there are sixteen and nothing else uses them.
Make this number configurable in the advanced options menu along with max
low memory size. If one wants 1 GB of lowmem, then it's typically
necessary to have four CAM entries.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code that maps kernel low memory would only use page sizes up to 256
MB. On E500v2 pages up to 4 GB are supported.
However, a page must be aligned to a multiple of the page's size. I.e.
256 MB pages must aligned to a 256 MB boundary. This was enforced by a
requirement that the physical and virtual addresses of the start of lowmem
be aligned to 256 MB. Clearly requiring 1GB or 4GB alignment to allow
pages of that size isn't acceptable.
To solve this, I simply have adjust_total_lowmem() take alignment into
account when it decides what size pages to use. Give it PAGE_OFFSET =
0x7000_0000, PHYSICAL_START = 0x3000_0000, and 2GB of RAM, and it will map
pages like this:
PA 0x3000_0000 VA 0x7000_0000 Size 256 MB
PA 0x4000_0000 VA 0x8000_0000 Size 1 GB
PA 0x8000_0000 VA 0xC000_0000 Size 256 MB
PA 0x9000_0000 VA 0xD000_0000 Size 256 MB
PA 0xA000_0000 VA 0xE000_0000 Size 256 MB
Because the lowmem mapping code now takes alignment into account,
PHYSICAL_ALIGN can be lowered from 256 MB to 64 MB. Even lower might be
possible. The lowmem code will work down to 4 kB but it's possible some of
the boot code will fail before then. Poor alignment will force small pages
to be used, which combined with the limited number of TLB1 pages available,
will result in very little memory getting mapped. So alignments less than
64 MB probably aren't very useful anyway.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code to map lowmem uses three CAM aka TLB[1] entries to cover it. The
size of each is stored in three globals named __cam0, __cam1, and __cam2.
All the code that uses them is duplicated three times for each of the three
variables.
We have these things called arrays and loops....
Once converted to use an array, it will be easier to make the number of
CAMs configurable.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We currently have a few variants of fsl-booke processors (e500v1, e500v2,
e500mc, and e200). They all have minor differences that we had previously
been handling via ifdefs.
To move towards having this support the following changes have been made:
* PID1, PID2 only exist on e500v1 & e500v2 and should not be accessed on
e500mc or e200. We use MMUCFG[NPIDS] to determine which case we are
since we only touch PID1/2 in extremely early init code.
* Not all IVORs exist on all the processors so introduce cpu_setup
functions for each variant to setup the proper IVORs that are either
unique or exist but have some variations between the processors
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pcie nodes to the appropriate dts files, plus adds
some probing code for the boards.
Also, remove of_device_is_avaliable() check from the mpc837x_mds.c
board file, as mpc83xx_add_bridge() has the same check now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for PCI-Express controllers as found on the
newer MPC83xx chips.
The work is loosely based on the Tony Li's patch[1], but unlike the
original patch, this patch implements sliding window for the Type 1
transactions using outbound window translations, so we don't have to
ioremap the whole PCI-E configuration space.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-January/049028.html
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix handling of _PAGE_COHERENT in BAT setup code
powerpc/pseries: Correct VIO bus accounting problem in CMO env.
powerpc: More printing warning fixes for the l64 to ll64 conversion
powerpc: Remove arch/ppc cruft from Kconfig
powerpc: Printing fix for l64 to ll64 conversion: phyp_dump.c
powerpc/embedded6xx: Update defconfigs
powerpc/8xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/mpc8313erdb: fix kernel panic because mdio device is not probed
powerpc/4xx: Update multi-board PowerPC 4xx defconfigs
powerpc/44x: Update PowerPC 44x defconfigs
powerpc/40x: Update PowerPC 40x defconfigs
powerpc/85xx: Fix typo in mpc8572ds dts
powerpc/44x: Warp patches for the new NDFC driver
powerpc/4xx: DTS: Add Add'l SDRAM0 Compatible and Interrupt Info
When there are multiple L1-aliasing userland mappings of the same physical
page, we currently remap each of them uncached, to prevent VIVT cache
aliasing issues. (E.g. writes to one of the mappings not being immediately
visible via another mapping.) However, when we do this remapping, there
could still be stale data in the L2 cache, and an uncached mapping might
bypass L2 and go straight to RAM. This would cause reads from such
mappings to see old data (until the dirty L2 line is eventually evicted.)
This issue is solved by forcing a L2 cache flush whenever the shared page
is made L1 uncacheable.
Ideally, we would make L1 uncacheable and L2 cacheable as L2 is PIPT. But
Feroceon does not support that combination, and the TEX=5 C=0 B=0 encoding
for XSc3 doesn't appear to work in practice.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 5329 ColdFire periphal addressing
uclinux: add process name to allocation error message
m68knommu: correct the mii calculations for 532x ColdFire FEC
m68knommu: add ColdFire M532x to the FEC configuration options
m68knommu: fix syscall restarting
m68knommu: remove the obsolete and long unused comempci chip support
m68knommu: remove the no longer used PCI support option
m68knommu: remove obsolete and unused eLIA board
m68knommu: set NO_DMA
m68knommu: fix cache flushing for the 527x ColdFire processors
m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
m68knommu: use one exist from execption
Aaro says:
> With spinlock debugs enabled I get might_sleep() warnings when using
> ptrace.
tracked down to a missing enable_irq before calling do_undefinstr().
Reported-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Tested-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-msm/board-halibut.c:45: error: implicit declaration of function 'MSM_GPIO_TO_INT'
arch/arm/mach-msm/board-halibut.c:45: error: initializer element is not constant
arch/arm/mach-msm/board-halibut.c:45: error: (near initialization for 'smc91x_resources[1].start')
arch/arm/mach-msm/board-halibut.c:46: error: initializer element is not constant
arch/arm/mach-msm/board-halibut.c:46: error: (near initialization for 'smc91x_resources[1].end')
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
_PAGE_COHERENT is now always set in _PAGE_RAM resp. PAGE_KERNEL.
Thus it has to be masked out, if the BAT mapping should be non
cacheable or CPU_FTR_NEED_COHERENT is not set.
This will work on normal SMP setups because we force-set
CPU_FTR_NEED_COHERENT as part of CPU_FTR_COMMON on SMP.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the VIO bus code the wrappers for dma alloc_coherent and free_coherent
calls are rounding to IOMMU_PAGE_SIZE. Taking a look at the underlying
calls, the actual mapping is promoted to PAGE_SIZE. Changing the
rounding in these two functions fixes under-reporting the entitlement
used by the system. Without this change, the system could run out of
entitlement before it believes it has and incur mapping failures at the
firmware level.
Also in the VIO bus code, the wrapper for dma map_sg is not exiting in
an error path where it should. Rather than fall through to code for the
success case, this patch adds the return that is needed in the error path.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove some leftover cruft from the arch/ppc days
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits)
USB: Driver for Freescale QUICC Engine USB Host Controller
USB: option: add QUANTA HSDPA Data Card device ids
USB: storage: Add another unusual_dev for off-by-one bug
USB: unusual_dev: usb-storage needs to ignore a device
USB: GADGET: fix !x & y
USB: new id for ti_usb_3410_5052 driver
USB: cdc-acm: Add another conexant modem to the quirks
USB: 'option' driver - onda device MT503HS has wrong id
USB: Remove ZTE modem from unusual_devices
USB: storage: support of Dane-Elec MediaTouch USB device
USB: usbmon: Implement compat_ioctl
USB: add kernel-doc for wusb_dev in struct usb_device
USB: ftdi_sio driver support of bar code scanner from Diebold
USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID
USB: cp2101 device
USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
USB: remove vernier labpro from ldusb
USB: CDC-ACM quirk for MTK GPS
USB: cdc-acm: support some gps data loggers
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
...
The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 5329 ColdFire peripheral IO register addresses are not relative to
the MBAR register. So fix the serial platform setup array and IRQ acking
to use just the direct addresses.
Signed-off-by: Matt Waddel <Matt.Waddel@freescale.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make restart blocks working, required for proper syscall restarting.
Derived from same changes for m68k arch by Andreas Schwab <schwab@suse.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer said about this board:
Only ever a handful where made, and that was in 1999.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
m68knommu does not set the Kconfig NO_DMA variable, but also does
not provide the required functions, resulting in the following
build error triggered by commit a40c24a133
(net: Add SKB DMA mapping helper functions.):
<-- snip -->
..
LD vmlinux
net/built-in.o: In function `skb_dma_unmap':
(.text+0xac5e): undefined reference to `dma_unmap_single'
net/built-in.o: In function `skb_dma_unmap':
(.text+0xac7a): undefined reference to `dma_unmap_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xacdc): undefined reference to `dma_map_single'
net/built-in.o: In function `skb_dma_map':
(.text+0xace8): undefined reference to `dma_mapping_error'
net/built-in.o: In function `skb_dma_map':
(.text+0xad10): undefined reference to `dma_map_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xad82): undefined reference to `dma_unmap_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xadc6): undefined reference to `dma_unmap_single'
make[1]: *** [vmlinux] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix cache flushing for the 527x ColdFire processors
Its CACR register format is slightly different.
Along with this add support for flushing the 523x cache, which uses
the same format as the 527x ColdFire's, and was missing flush support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Part of the code that did not make sense to me got removed by Greg.
This is part two:
The first compare is to check whether the interrupts are disabled or not.
Depending on the result we exectute the RESTORE_ALL macro is not only
restoring the stack but also returning to caller.
The test for pending softirq has been removed because it is allready done
in irq_exit().
Since system_call() is allso using the SAVE_ALL macro and returning via
ret_from_exception label I see no reason why we could not do this here
as well. This is also handy because if we return from the timer interrupt
and we need to resched than we check for this :)
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Warn on deprecated binding model use
eeprom: More consistent symbol names
eeprom: Move 93cx6 eeprom driver to /drivers/misc/eeprom
spi: Move at25 (for SPI eeproms) to /drivers/misc/eeprom
i2c: Move old eeprom driver to /drivers/misc/eeprom
i2c: Move at24 to drivers/misc/eeprom
i2c: Quilt tree has moved
i2c: Delete many unused adapter IDs
i2c: Delete 10 unused driver IDs
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix DAX handling via userspace access from kernel.
sparc64: Annotate sparc64 specific syscalls with SYSCALL_DEFINEx()
[CVE-2009-0029] sparc: Enable syscall wrappers for 64-bit
sparc64: Initialize FHC/CLOCK LED platform_device 'id' field correctly.
sparc64: fix modpost failure
sparc64: fix readout of cpu/fpu type
Probe the new mdio node added by b31a1d8b. Fix kernel panic problem when
gianfar driver wants to get the of_platform_device of that mdio.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.
Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
swab.h seems to have been missed during the header merge.
Add conditionals similar to byteorder.h and remove the
now unnecessary byteorder_no/mm.h
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
i.MX31: framebuffer driver
i.MX31: Image Processing Unit DMA and IRQ drivers
dmaengine: add async_tx_clear_ack() macro
dmaengine: dma_issue_pending_all == nop when CONFIG_DMA_ENGINE=n
dmaengine: kill some dubious WARN_ONCEs
fsldma: print correct IRQ on mpc83xx
fsldma: check for NO_IRQ in fsl_dma_chan_remove()
dmatest: Use custom map/unmap for destination buffer
fsldma: use a valid 'device' for dma_pool_create
dmaengine: fix dependency chaining
* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (22 commits)
dma-coherent: Restore dma_alloc_from_coherent() large alloc fall back policy.
dma-coherent: per-device coherent area is in pages, not bytes.
sh: fix unaligned and nonexistent address handling
nommu: Stub in vm_map_ram()/vm_unmap_ram()/vm_unmap_aliases().
sh: fix sh-sci / early printk build on sh7723
sh: export the sh7343 JPU to user space
sh: update defconfigs.
serial: sh-sci: Fix up SH7720/SH7721 SCI build.
sh: Kill off obsolete busses from arch/sh/Kconfig.
sh: sh7785lcr/highlander/hp6xx need linux/irq.h.
sh: Migo-R MMC support using spi_gpio and mmc_spi.
sh: ap325rxa MMC support using spi_gpio and mmc_spi
sh: mach-x3proto: needs linux/irq.h.
sh: Drop the BKL from sys_execve() on SH-5.
sh: convert rsk7203 to use smsc911x.
sh: convert magicpanelr2 platform to use smsc911x.
sh: convert ap325rxa platform to use smsc911x.
sh: mach-migor: Add tw9910 support.
sh: mach-migor: Delete soc_camera_platform setup.
sh: mach-migor: Add ov772x support.
...
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debugobjects: add and use INIT_WORK_ON_STACK
rcu: remove duplicate CONFIG_RCU_CPU_STALL_DETECTOR
relay: fix lock imbalance in relay_late_setup_files
oprofile: fix uninitialized use of struct op_entry
rcu: move Kconfig menu
softlock: fix false panic which can occur if softlockup_thresh is reduced
rcu: add __cpuinit to rcu_init_percpu_data()
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimers: fix inconsistent lock state on resume in hres_timers_resume
time-sched.c: tick_nohz_update_jiffies should be static
locking, hpet: annotate false positive warning
kernel/fork.c: unused variable 'ret'
itimers: remove the per-cpu-ish-ness
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (29 commits)
xen: unitialised return value in xenbus_write_transaction
x86: fix section mismatch warning
x86: unmask CPUID levels on Intel CPUs, fix
x86: work around PAGE_KERNEL_WC not getting WC in iomap_atomic_prot_pfn.
x86: use standard PIT frequency
xen: handle highmem pages correctly when shrinking a domain
x86, mm: fix pte_free()
xen: actually release memory when shrinking domain
x86: unmask CPUID levels on Intel CPUs
x86: add MSR_IA32_MISC_ENABLE bits to <asm/msr-index.h>
x86: fix PTE corruption issue while mapping RAM using /dev/mem
x86: mtrr fix debug boot parameter
x86: fix page attribute corruption with cpa()
Revert "x86: signal: change type of paramter for sys_rt_sigreturn()"
x86: use early clobbers in usercopy*.c
x86: remove kernel_physical_mapping_init() from init section
fix: crash: IP: __bitmap_intersects+0x48/0x73
cpufreq: use work_on_cpu in acpi-cpufreq.c for drv_read and drv_write
work_on_cpu: Use our own workqueue.
work_on_cpu: don't try to get_online_cpus() in work_on_cpu.
...
Impact: re-enable CPUID unmasking on affected processors
As far as I am capable of discerning from the documentation,
MSR_IA32_MISC_ENABLE should be available for all family 0xf CPUs, as
well as family 6 for model >= 0xd (newer Pentium M).
The documentation on this isn't ideal, so we need to be on the lookout
for errors, still.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Here function vmi_activate calls a init function activate_vmi , which
causes the following section mismatch warnings:
LD arch/x86/kernel/built-in.o
WARNING: arch/x86/kernel/built-in.o(.text+0x13ba9): Section mismatch
in reference from the function vmi_activate() to the function
.init.text:vmi_time_init()
The function vmi_activate() references
the function __init vmi_time_init().
This is often because vmi_activate lacks a __init
annotation or the annotation of vmi_time_init is wrong.
WARNING: arch/x86/kernel/built-in.o(.text+0x13bd1): Section mismatch
in reference from the function vmi_activate() to the function
.devinit.text:vmi_time_bsp_init()
The function vmi_activate() references
the function __devinit vmi_time_bsp_init().
This is often because vmi_activate lacks a __devinit
annotation or the annotation of vmi_time_bsp_init is wrong.
WARNING: arch/x86/kernel/built-in.o(.text+0x13bdb): Section mismatch
in reference from the function vmi_activate() to the function
.devinit.text:vmi_time_ap_init()
The function vmi_activate() references
the function __devinit vmi_time_ap_init().
This is often because vmi_activate lacks a __devinit
annotation or the annotation of vmi_time_ap_init is wrong.
Fix it by marking vmi_activate() as __init too.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix boot hang on pre-model-15 Intel CPUs
rdmsrl_safe() does not work in very early bootup code yet, because we
dont have the pagefault handler installed yet so exception section
does not get parsed. rdmsr_safe() will just crash and hang the bootup.
So limit the MSR_IA32_MISC_ENABLE MSR read to those CPU types that
support it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The EH message for NODEV_HINT path was describing the opposite
condition. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In the absence of PAT, PAGE_KERNEL_WC ends up mapping to a memory type that
gets UC behavior even in the presence of a WC MTRR covering the area in
question. By swapping to PAGE_KERNEL_UC_MINUS, we can get the actual
behavior the caller wanted (WC if you can manage it, UC otherwise).
This recovers the 40% performance improvement of using WC in the DRM
to upload vertex data.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Tomi Valkeinen reports:
Running with latest linux-omap kernel on OMAP3 SDP board, I have
problem with iounmap(). It looks like iounmap() does not properly
free large areas. Below is a test which fails for me in 6-7 loops.
for (i = 0; i < 200; ++i) {
vaddr = ioremap(paddr, size);
if (!vaddr) {
printk("couldn't ioremap\n");
break;
}
iounmap(vaddr);
}
The changes to vmalloc.c weren't reflected in the ARM ioremap
implementation. Turns out the fix is rather simple.
Tested-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Tested-by: Matt Gerassimoff <mgeras@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
the RDC and ELAN platforms use slighly different PIT clocks, resulting in
a timex.h hack that changes PIT_TICK_RATE during build time. But if a
tester enables any of these platform support .config options, the PIT
will be miscalibrated on standard PC platforms.
So use one frequency - in a subsequent patch we'll add a quirk to allow
x86 platforms to define different PIT frequencies.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The old matching algorithm was too fuzzy, causing false positives.
For example, when asked for device D connection C1 and we only find
device D connection C2, we return that as a valid match despite the
connection names being different.
Change the algorithm such that:
An entry with a NULL ID is assumed to be a wildcard.
If an entry has a device ID, it must match
If an entry has a connection ID, it must match
However, we maintain the order of precidence while still only doing
a single pass over all entries: dev+con > dev only > con only.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: David Brownell <dbrownell@users.sourceforge.net>
Subject: ARM/mach-davinci/usb.c buildfix
CC arch/arm/mach-davinci/usb.o
arch/arm/mach-davinci/usb.c:60: error: 'IRQ_USBINT' undeclared here (not in a function)
make[1]: *** [arch/arm/mach-davinci/usb.o] Error 1
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On -rt we were seeing spurious bad page states like:
Bad page state in process 'firefox'
page:c1bc2380 flags:0x40000000 mapping:c1bc2390 mapcount:0 count:0
Trying to fix it up, but a reboot is needed
Backtrace:
Pid: 503, comm: firefox Not tainted 2.6.26.8-rt13 #3
[<c043d0f3>] ? printk+0x14/0x19
[<c0272d4e>] bad_page+0x4e/0x79
[<c0273831>] free_hot_cold_page+0x5b/0x1d3
[<c02739f6>] free_hot_page+0xf/0x11
[<c0273a18>] __free_pages+0x20/0x2b
[<c027d170>] __pte_alloc+0x87/0x91
[<c027d25e>] handle_mm_fault+0xe4/0x733
[<c043f680>] ? rt_mutex_down_read_trylock+0x57/0x63
[<c043f680>] ? rt_mutex_down_read_trylock+0x57/0x63
[<c0218875>] do_page_fault+0x36f/0x88a
This is the case where a concurrent fault already installed the PTE and
we get to free the newly allocated one.
This is due to pgtable_page_ctor() doing the spin_lock_init(&page->ptl)
which is overlaid with the {private, mapping} struct.
union {
struct {
unsigned long private;
struct address_space *mapping;
};
spinlock_t ptl;
struct kmem_cache *slab;
struct page *first_page;
};
Normally the spinlock is small enough to not stomp on page->mapping, but
PREEMPT_RT=y has huge 'spin'locks.
But lockdep kernels should also be able to trigger this splat, as the
lock tracking code grows the spinlock to cover page->mapping.
The obvious fix is calling pgtable_page_dtor() like the regular pte free
path __pte_free_tlb() does.
It seems all architectures except x86 and nm10300 already do this, and
nm10300 doesn't seem to use pgtable_page_ctor(), which suggests it
doesn't do SMP or simply doesnt do MMU at all or something.
Signed-off-by: Peter Zijlstra <a.p.zijlsta@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Add wrapper functions for the following compat system calls:
* readahead
* sendfile64
* tkill
* tgkill
* keyctl
This ensures that the high order bits of the parameter registers are correctly
sign extended.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Precreate stop_machine threads in case the machine supports ETR/STP.
Otherwise we might deadlock if a time sync operation gets scheduled
and the creation of stop_machine threads would cause disk I/O.
This is just the minimal fix.
The real fix would be to only precreate stop_machine threads if
ETR/STP is actually used. But that would be a rather large and
complicated patch.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
On (initial) cpu hotplug the lowcore values for user_timer and
system_timer don't get initialized like they would get on each
process schedule.
On initial start of secondary cpus this leads to the situation
where per thread user/system_timer values are larger than the
corresponding contents of the lowcore. When later calculating
time spent in user/system context the result can be negative.
So for cpu hotplug we should manually initialize lowcore values.
Fixes this bug:
Kernel BUG at 000ec080 [verbose debug info unavailable]
fixpoint divide exception: 0009 [#1] PREEMPT SMP
Modules linked in:
CPU: 10 Not tainted 2.6.28 #4
Process sysctl (pid: 975, task: 3fa752e0, ksp: 3fbebca0)
Krnl PSW : 070c1000 800ec080 (show_stat+0x390/0x5fc)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:0 CC:1 PM:0
Krnl GPRS: 7fffffff fefc7ce5 3faec080 003879ae
00000001 01388000 7fffffff 01388000
00000000 00000000 0049ad50 3fbebcf8
01388000 002f51a8 800ec1fe 3fbebcf8
Krnl Code: 800ec076: 9001b188 stm %r0,%r1,392(%r11)
800ec07a: 9801b0c0 lm %r0,%r1,192(%r11)
800ec07e: 1d05 dr %r0,%r5
>800ec080: 9001b0c0 stm %r0,%r1,192(%r11)
800ec084: 5860b0c4 l %r6,196(%r11)
800ec088: 1806 lr %r0,%r6
800ec08a: 8c800001 srdl %r8,1
800ec08e: 1d87 dr %r8,%r7
Call Trace:
([<00000000000ec1ee>] show_stat+0x4fe/0x5fc)
[<00000000000c13e8>] seq_read+0xc4/0x3ac
[<00000000000e4796>] proc_reg_read+0x6e/0x9c
[<00000000000a6a44>] vfs_read+0x78/0x100
[<00000000000a6ba8>] sys_read+0x40/0x80
[<00000000000234a8>] sysc_do_restart+0x1a/0x1e
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
When 31 bit user space programs call sigaltstack on a 64 bit Linux
OS, the system call returns -1 with errno=EFAULT. The 31 bit pointer passed
to the system call is extended to 64 bit, but the high order bits are not
set to zero. The kernel detects the invalid user space pointer and
returns -EFAULT. To solve the problem, sys32_sigaltstack_wrapper()
instead of sys32_sigaltstack() has to be called. The wrapper function sets
the high order bits to zero.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Use the personality() macro to mask out all bits that are not
relevant for the personality type.
The personality field contains bits for other things as well,
so without masking out the not relevalent bits the comparison
won't do what is expected.
Reported-by: Andreas Krebbel <krebbel@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cleanup the cpuid check for DS configuration.
This also fixes a Corei7 CPUID enumeration bug.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Fix debugobjects warning
debugobject enabled kernels spit out a warning in hpet code due to a
workqueue which is initialized on stack.
Add INIT_WORK_ON_STACK() which calls init_timer_on_stack() and use it
in hpet.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: Fixes crashes with misconfigured BIOSes on XSAVE hardware
Avuton Olrich reported early boot crashes with v2.6.28 and
bisected it down to dc1e35c6e9
("x86, xsave: enable xsave/xrstor on cpus with xsave support").
If the CPUID limit bit in MSR_IA32_MISC_ENABLE is set, clear it to
make all CPUID information available. This is required for some
features to work, in particular XSAVE.
Reported-and-bisected-by: Avuton Olrich <avuton@gmail.com>
Tested-by: Avuton Olrich <avuton@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: None (new bit definitions currently unused)
Add bit definitions for the MSR_IA32_MISC_ENABLE MSRs to
<asm/msr-index.h>.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Beschorner Daniel reported:
> hwinfo problem since 2.6.28, showing this in the oops:
> Corrupted page table at address 7fd04de3ec00
Also, PaX Team reported a regression with this commit:
> commit 9542ada803
> Author: Suresh Siddha <suresh.b.siddha@intel.com>
> Date: Wed Sep 24 08:53:33 2008 -0700
>
> x86: track memtype for RAM in page struct
This commit breaks mapping any RAM page through /dev/mem, as the
reserve_memtype() was not initializing the return attribute type and as such
corrupting the PTE entry that was setup with the return attribute type.
Because of this bug, application mapping this RAM page through /dev/mem
will die with "Corrupted page table at address xxxx" message in the kernel
log and also the kernel identity mapping which maps the underlying RAM
page gets converted to UC.
Fix this by initializing the return attribute type before calling
reserve_ram_pages_type()
Reported-by: PaX Team <pageexec@freemail.hu>
Reported-and-tested-by: Beschorner Daniel <Daniel.Beschorner@facton.com>
Tested-and-Acked-by: PaX Team <pageexec@freemail.hu>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is a framebuffer driver for i.MX31 SoCs. It only supports synchronous
displays, vertical panning supported, no overlay support.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
while looking at:
http://bugzilla.kernel.org/show_bug.cgi?id=11541
I realized that the mtrr.show param cannot work, because
the code is processed much too early.
This patch:
- Declares mtrr.show as early_param
- Stays consistent with the previous param (which I doubt
that it ever worked), so mtrr.show=1 would still work
- Declares mtrr_show as initdata
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix sporadic slowdowns and warning messages
This patch fixes a performance issue reported by Linus on his
Nehalem system. While Linus reverted the PAT patch (commit
58dab916df) which exposed the issue,
existing cpa() code can potentially still cause wrong(page attribute
corruption) behavior.
This patch also fixes the "WARNING: at arch/x86/mm/pageattr.c:560" that
various people reported.
In 64bit kernel, kernel identity mapping might have holes depending
on the available memory and how e820 reports the address range
covering the RAM, ACPI, PCI reserved regions. If there is a 2MB/1GB hole
in the address range that is not listed by e820 entries, kernel identity
mapping will have a corresponding hole in its 1-1 identity mapping.
If cpa() happens on the kernel identity mapping which falls into these holes,
existing code fails like this:
__change_page_attr_set_clr()
__change_page_attr()
returns 0 because of if (!kpte). But doesn't
set cpa->numpages and cpa->pfn.
cpa_process_alias()
uses uninitialized cpa->pfn (random value)
which can potentially lead to changing the page
attribute of kernel text/data, kernel identity
mapping of RAM pages etc. oops!
This bug was easily exposed by another PAT patch which was doing
cpa() more often on kernel identity mapping holes (physical range between
max_low_pfn_mapped and 4GB), where in here it was setting the
cache disable attribute(PCD) for kernel identity mappings aswell.
Fix cpa() to handle the kernel identity mapping holes. Retain
the WARN() for cpa() calls to other not present address ranges
(kernel-text/data, ioremap() addresses)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
unaligned and nonexistent address causes wrong exception
handling in traps_32.c(handle_unaligned_access).
'handle_unalinged_ins' should return -EFAULT if address error
is fixed up with kernel exception table, otherwise
'handle_unaligned_access' increases already fixed program counter
and then crash.
for example
ioctl(fd, TCGETA, (struct termio *)-1)
never return and stay in TASK_UNINTERRUPTIBLE state forever
in my kernel.
Signed-off-by: SUGIOKA Toshinobu <sugioka@itonet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the sh7343 JPU to user space using uio_pdrv_genirq,
very similar to the sh7722 JPU patch by Hayama-san.
While at it fix up the end of the sh7722 JPU iomem resource.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Mike Frysinger