This patch adds a work-around for handling zero allocation length
control CDBs (type SCF_SCSI_CONTROL_SG_IO_CDB) that was causing an
OOPs with the following raw calls:
# sg_raw -v /dev/sdd 3 0 0 0 0 0
# sg_raw -v /dev/sdd 0x1a 0 1 0 0 0
This patch will follow existing zero-length handling for data I/O
and silently return with GOOD status. This addresses the zero length
issue, but the proper long-term resolution for handling arbitary
allocation lengths will be to refactor out data-phase handling in
individual CDB emulation logic within target_core_cdb.c
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
According to SPC-4, the sense key for commands that are failed with
INVALID FIELD IN PARAMETER LIST and INVALID FIELD IN CDB should be
ILLEGAL REQUEST (5h) rather than ABORTED COMMAND (Bh). Without this
patch, a tcm_loop LUN incorrectly gives:
# sg_raw -r 1 -v /dev/sda 3 1 0 0 ff 0
Sense Information:
Fixed format, current; Sense key: Aborted Command
Additional sense: Invalid field in cdb
Raw sense data (in hex):
70 00 0b 00 00 00 00 0a 00 00 00 00 24 00 00 00
00 00
While a real SCSI disk gives:
Sense Information:
Fixed format, current; Sense key: Illegal Request
Additional sense: Invalid field in cdb
Raw sense data (in hex):
70 00 05 00 00 00 00 18 00 00 00 00 24 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
with the main point being that the real disk gives a sense key of
ILLEGAL REQUEST (5h).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Doing alloc_page(GFP_KERNEL | __GFP_ZERO) to get pages used for data
buffers wastes a lot of CPU clearing pages that will be quickly be
overwritten by the actual data. However, for emulated control
commands such as INQUIRY and so on, the code does assume that the
buffer is zeroed.
To avoid this CPU overhead, skip the __GFP_ZERO for commands that are
actually moving data, ie cmds that have SCF_SCSI_DATA_SG_IO_CDB set.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Initiators that aren't the active reservation holder should be able to
do a PERSISTENT RESERVE IN command in all cases, so add it to the list
of allowed CDBs in core_scsi3_pr_seq_non_holder().
Signed-off-by: Marco Sanvido <marco@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The comments quote the right parts of the spec:
* d) Establish a unit attention condition for the
* initiator port associated with every I_T nexus
* that lost its registration other than the I_T
* nexus on which the PERSISTENT RESERVE OUT command
* was received, with the additional sense code set
* to REGISTRATIONS PREEMPTED.
and
* e) Establish a unit attention condition for the initiator
* port associated with every I_T nexus that lost its
* persistent reservation and/or registration, with the
* additional sense code set to REGISTRATIONS PREEMPTED;
but the actual code accidentally uses ASCQ_2AH_RESERVATIONS_PREEMPTED
instead of ASCQ_2AH_REGISTRATIONS_PREEMPTED. Fix this.
Signed-off-by: Marco Sanvido <marco@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We never embedd the bio into a structure, so there is no need to allocate
64 bytes of headroom per bio.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The target code was not setting the additional sense length field in the
sense data it returned, which meant that at least the Linux stack
ignored the ASC/ASCQ fields. For example, without this patch, on a
tcm_loop device:
# sg_raw -v /dev/sda 2 0 0 0 0 0
gives
cdb to send: 02 00 00 00 00 00
SCSI Status: Check Condition
Sense Information:
Fixed format, current; Sense key: Illegal Request
Raw sense data (in hex):
70 00 05 00 00 00 00 00
while after the patch we correctly get the following (which matches what
a regular disk returns):
cdb to send: 02 00 00 00 00 00
SCSI Status: Check Condition
Sense Information:
Fixed format, current; Sense key: Illegal Request
Additional sense: Invalid command operation code
Raw sense data (in hex):
70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00
00 00
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes a legacy se_dev_check_online() check from within
transport_execute_tasks() that should no longer be necessary as
transport_lookup_cmd_lun() is already making this call.
Using transport_cmd_check_stop() from transport_execute_tasks() should
already be checking per se_cmd context for each descriptor upon active
I/O shutdown, so no need to acquire dev->dev_status_lock again while
executing se_task submission.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes the original usage of __transport_execute_tasks() ahead
of every transport_get_cmd_from_queue() call in transport_processing_thread().
This helps reduce se_device->execute_task_lock contention between qla2xxx wq
with target_submit_cmd() for READs and transport_processing_thread()
context servicing WRITEs with full payloads for I/O submission.
It also adds a __transport_execute_tasks() to kick the task queue again
without a *se_cmd descriptor with existing queue full logic, but this may
end up not being necessary.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes __transport_execute_tasks() perform the addition of
tasks to dev->execute_task_list via __transport_add_tasks_from_cmd()
while holding dev->execute_task_lock during normal I/O fast path
submission.
It effectively removes the unnecessary re-acquire of dev->execute_task_lock
during transport_execute_tasks() -> transport_add_tasks_from_cmd() ahead
of calling __transport_execute_tasks() to queue tasks for the passed
*se_cmd descriptor.
(v2: Re-add goto check_depth usage for multi-task submission for now..)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Historically, pSCSI devices have been the ones that required target-core
to enforce a per se_device->depth_left. This patch changes target-core
to no longer (by default) enforce a per se_device->depth_left or sleep in
transport_tcq_window_closed() when we out of queue slots for all backend
export cases.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes __transport_execute_tasks() use a local *se_dev
reference to prevent direct se_cmd->se_dev access after
transport_cmd_check_stop() -> transport_add_tasks_from_cmd()
has been called, as in the current implementation we can expect
__transport_execute_tasks() may be called from another context
that may have already completed the I/O.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the main ft_send_work() I/O path to use
target_submit_cmd() with a single se_cmd->cmd_kref reference
that is released via the existing ft_check_stop_free() response
path callback.
It also makes ft_send_tm() use transport_init_se_cmd() and
target_get_sess_cmd() to also use single se_cmd->cmd_kref
reference.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a target_submit_cmd() caller that can be used by fabrics
to submit an uninitialized se_cmd descriptor to an struct se_session +
unpacked_lun from workqueue process context. This call will invoke the
following steps:
- transport_init_se_cmd() to setup se_cmd specific pointers
- Obtain se_cmd->cmd_kref references with target_get_sess_cmd()
- set se_cmd->t_tasks_bidi
- transport_lookup_cmd_lun() to setup struct se_cmd->se_lun from
the passed unpacked_lun
- transport_generic_allocate_tasks() to setup the passed *cdb, and
- transport_handle_cdb_direct() handle READ dispatch or WRITE
ready-to-transfer callback to fabric
v2 changes from hch feedback:
*) Add target_sc_flags_table for target_submit_cmd flags
*) Rename bidi parameter to flags, add TARGET_SCF_BIDI_OP
*) Convert checks to BUG_ON
*) Add out_check_cond for transport_send_check_condition_and_sense
usage
v3 changes:
*) Add TARGET_SCF_ACK_KREF for target_submit_cmd into
target_get_sess_cmd to determine when the fabric caller is expecting
a second kref_put() from fabric packet acknowledgement.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves target_put_sess_cmd() to use a se_cmd->cmd_kref
callback target_release_cmd_kref when performing driver release of
fabric->se_cmd descriptor memory. It sets the default cmd_kref
count value to '2' within target_get_sess_cmd() setup, and
currently assumes TFO->check_stop_free() usage.
It drops se_tfo->check_release_cmd() usage in the main
transport_release_cmd codepath.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Current SCSI specs say that the "response format" field in the standard
INQUIRY response should be set to 2, and all the real SCSI devices I
have do put 2 here. So let's do that too.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is not reason to artifically limit max_sectors in tcm_loop, set
it to UINT_MAX to allow stressing the large I/O handling in the target
core using the loopback driver. Also remove various superflous defines
hiding the values set in the host template.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch strips the trailing newline from backend device udev_path and
alias attributes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes chap_server_compute_md5() use proper unsigned long
usage for the CHAP_I (identifier) and check for values beyond 255 as
per RFC-1994.
Reported-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A reader should spend an extra moment whenever noticing a cast,
because either something special is going on that deserves extra
attention or, as is all too often the case, the code is wrong.
These casts, afaics, have all been useless. They cast a foo* to a
foo*, cast a void* to the assigned type, cast a foo* to void*, before
assigning it to a void* variable, etc.
In a few cases I also removed an additional &...[0], which is equally
useless.
Lastly I added three FIXMEs where, to the best of my judgement, the
code appears to have a bug. It would be good if someone could check
these.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- rename to target_check_cdb_and_preempt
- use non-safe list_for_each_entry
- move common check into callee (simplifying callers)
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The command
| echo rd_pages=32768 > ramdisk/control
Does not work because it writes "rd_pages=32768\n" and the parser which
matches for "rd_pages=%d" does not recognize it due to the \n. One way
of fixing this would be using "echo -n" instead.
This patch adds \n to the list of separators so we don't have to use the
-n argument which I find is more convinient.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is no need to make task_state_active an atomic_t given that it is
always set under the execute_task_lock so we can make it a simple bool.
Also rename it to t_state_active to be closer to the list it guards,
and make sure all checks before the list addion/removal actually happen
under execute_task_lock.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We only reach transport_complete_task once per task, so the test and set on
task_error_status is never going to have an effect.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This reorganized the headers under include/target into:
- target_core_base.h stays as is with all target-wide data stuctures and defines
- target_core_backend.h contains the whole interface to I/O backends
- target_core_fabric.h contains the whole interface to fabric modules
Except for those only the various configfs macro headers stay around.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Create a new headers, drivers/target/target_core_internal.h that is supposed
to hold all target_core-internal prototypes. Move all non-exported includes
from include/target to it, and merge the smaller prototype-only includes
inside drivers/target into it as well. Mark functions that were found to
not be called outside their implementation file static.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix the following compile warning with hex2bin() usage:
drivers/target/iscsi/iscsi_target_auth.c: In function ‘chap_string_to_hex’:
drivers/target/iscsi/iscsi_target_auth.c:35: warning: ignoring return value of ‘hex2bin’, declared with attribute warn_unused_result
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If an attribute is present (but not yet supported) it should be OK
to write 0 (a no-op) to the attribute.
This is an issue because userspace should be able to save and restore all
set attribute values without error.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
So the code assumes that the sg list is only a array while in reality
loopback SGL memory via scsi_cmnd into target-core may be already
chained. This patch converts ramdisk code to use sg_miter logic from
scatterlist.h in order to properly support passthrough SGL usage with
transport_generic_map_mem_to_cmd() via loopback.
With this patch the bug goes away. However after umount/mount of the
device my files are gone. So something is still not right. After looking
at it for a while I decided to rewrite the that part of the code and now
things do work for me.
For reference:
- http://article.gmane.org/gmane.linux.scsi.target.devel/595
the sg_next() conversion
- http://article.gmane.org/gmane.linux.scsi.target.devel/602
the rewrite of the copy code
(nab: Fix compile warning in rd_MEMCPY)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Breakout rd_MEMCPY_do_task() usage of do_div() to tmp value during
rd_request->rd_page assignment.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes fileio to use for_each_sg() when walking se_task->task_sg
memory passed into from loopback LLD struct scsi_cmnd scatterlist memory.
This addresses an issue where FILEIO backends with loopback where hitting the
following OOPs with mkfs.ext2:
|kernel BUG at include/linux/scatterlist.h:97!
|invalid opcode: 0000 [#1] PREEMPT SMP
|Modules linked in: sd_mod tcm_loop target_core_stgt scsi_tgt target_core_pscsi target_core_file target_core_iblock target_core_mod configfs scsi_mod
|
|Pid: 671, comm: LIO_fileio Not tainted 3.1.0-rc10+ #139 Bochs Bochs
|EIP: 0060:[<e0afd746>] EFLAGS: 00010202 CPU: 0
|EIP is at fd_do_task+0x396/0x420 [target_core_file]
| [<e0aa7884>] __transport_execute_tasks+0xd4/0x190 [target_core_mod]
| [<e0aa797c>] transport_execute_tasks+0x3c/0xf0 [target_core_mod]
|EIP: [<e0afd746>] fd_do_task+0x396/0x420 [target_core_file] SS:ESP 0068:dea47e90
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Some are never used, some are set but never read, dev_hoq_count is
incremented and decremented, but never read.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The LSB of the page length is at offset 3, not 2.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SBC-3 says:
A TRANSFER LENGTH field set to zero specifies that 256 logical
blocks shall be written. Any other value specifies the number
of logical blocks that shall be written.
The old code was always just returning the value in the TRANSFER LENGTH
byte. Fix this to return 256 if the byte is 0.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
IO commands with a TRANSFER LENGTH of 0 are not an error; for example,
for READ (10) and WRITE (10), SBC-3 says:
A TRANSFER LENGTH field set to zero specifies that no logical blocks
shall be read. This condition shall not be considered an error.
In case we have nothing to do, just complete the command with good status.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch sets the missing ISCSI_FLAG_CMD_FINAL bit in
iscsit_send_task_mgt_rsp() for a struct iscsi_tm_rsp PDU.
This usage is hardcoded for all TM response PDUs in RFC-3720
section 10.6.
Reported-by: whucecil <whucecil1999@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes iscsi-target handling of underflow where residual data is
causing an OOPs by using the incorrect iscsi_cmd_t->data_length initially
assigned in iscsit_allocate_se_cmd(). It resets iscsi_cmd_t->data_length
from se_cmd_t->data_length after transport_generic_allocate_tasks()
has been invoked in iscsit_handle_scsi_cmd() RX context, and converts
iscsi_cmd->residual_count usage to access iscsi_cmd->se_cmd.residual_count
to get the proper residual count set by target-core.
Reported-by: <lists@internyc.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes transport_generic_map_mem_to_cmd() to reject SCSI data
overflow and to send exception status with CHECK_CONDITION + TCM_INVALID_CDB_FIELD
for fabrics that are passing a pre-populated struct scatterlist (eg: tcm_loop
and iscsi-target) being mapped into se_cmd->t_data_sg and se_cmd->t_data_nents.
This addresses an OOPs where transport_allocate_data_tasks() would walk
the incorrect post OVERFLOW cmd->data_length value beyond the end of
the passed scatterlist.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We never walk ordered_cmd_list in the se_device, so remove all code related
to supporting it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We already have a perfectly valid se_device pointer in the command, so
remove the mostly useless duplicates.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes config_item_name() informational usage of
TFO->free_wwn() treewide in loopback, tcm_fc, ib_srpt and
tcm_vhost module code.
Using v4 target_core_fabric_configfs.c logic, a fabric call for
config_item_name() in TFO->drop_wwn() context returns NULL as
target_fabric_drop_wwn() invoking config_item_put() ->
config_group_put() will release fabric_port->port_wwn.wwn_group
before the last config_item_put() -> TFO->drop_wwn() is
invoked.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
While testing ib_srpt I noticed that the target system became
rather unresponsive during intensive I/O. The patch below made
my target system responsive again during I/O without decreasing
performance.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds missing kfree() for an allocation in iscsi_login_zero_tsih_s1()
code, and make transport_init_session() check for IS_ERR() returns.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes legacy usage of PYX_TRANSPORT_* return codes in a number
of locations and addresses cases where transport_generic_request_failure()
was returning the incorrect sense upon CHECK_CONDITION status after the
v3.1 converson to use errno return codes.
This includes the conversion of transport_generic_request_failure() to
process cmd->scsi_sense_reason and handle extra TCM_RESERVATION_CONFLICT
before calling transport_send_check_condition_and_sense() to queue up
response status. It also drops PYX_TRANSPORT_OUT_OF_MEMORY_RESOURCES legacy
usgae, and returns TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE w/ a response
for these cases.
transport_generic_allocate_tasks(), transport_generic_new_cmd(), backend
SCF_SCSI_DATA_SG_IO_CDB ->do_task(), and emulated ->execute_task() have
all been updated to set se_cmd->scsi_sense_reason and return errno codes
universally upon failure. This includes cmd->scsi_sense_reason assignment
in target_core_alua.c, target_core_pr.c and target_core_cdb.c emulation code.
Finally it updates fabric modules to remove the legacy usage, and for
TFO->new_cmd_map() callers forwards return values outside of fabric code.
iscsi-target has also been updated to remove a handful of special cases
related to the cleanup and signaling QUEUE_FULL handling w/ ft_write_pending()
(v2: Drop extra SCF_SCSI_CDB_EXCEPTION check during failure from
transport_generic_new_cmd, and re-add missing task->task_error_status
assignment in transport_complete_task)
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Instead of calling into transport_emulate_control_cdb from
__transport_execute_tasks for some CDBs always set up ->exectute_tasks
in the command sequence and use it uniformly.
(nab: Add default passthrough break for SERVICE_ACTION_IN)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All ->execute_task instances now need to complete the I/O explicitly,
which can either happen synchronously or asynchronously.
Note that a lot of the CDB emulations appear to return success even if
some lowlevel operations failed. Given that this is an existing issue
this patch doesn't change that fact.
(nab: Adding missing switch breaks in PR-IN + PR_OUT)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Encapsulate each CDB emulation into a function of its own, to prepare
setting ->exectute_task to these routines.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We want to be able to handle all CDBs through it and remove hacks like
always using the first task in a CDB in target_report_luns.
Also rename the callback to ->execute_task to better describe its use.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Split core_scsi2_emulate_crh into one routine each for the
PERSISTENT_RESERVE_IN and PERSISTENT_RESERVE_OUT side.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Split core_scsi2_emulate_crh into one routine each for the reserve and
release side. The common code now is in a helper called by both
routines.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the initial pieces of generic active I/O shutdown logic.
This is intended to be a 'opt-in' feature for fabric modules that
includes the following functions to provide a mechinism for fabric
modules to track se_cmd via se_session->sess_cmd_list:
*) target_get_sess_cmd() - Add se_cmd to sess->sess_cmd_list, called
from fabric module incoming I/O path.
*) target_put_sess_cmd() - Check for completion or drop se_cmd from
->sess_cmd_list
*) target_splice_sess_cmd_list() - Splice active I/O list from
->sess_cmd_list to ->sess_wait_list, can called with HW fabric
lock held.
*) target_wait_for_sess_cmds() - Walk ->sess_wait_list waiting on
individual ->cmd_wait_comp. Optional transport_wait_for_tasks()
call.
target_splice_sess_cmd_list() is allowed to be called under HW fabric
lock, and performs the splice into se_sess->sess_wait_list and set
se_cmd->cmd_wait_set. Then target_wait_for_sess_cmds() walks the list
waiting for individual target_put_sess_cmd() fabric callbacks to
complete.
It also adds TFO->check_release_cmd() to split the completion and memory
release calls, where a fabric module uses target_put_sess_cmd() to check
for I/O completion during session shutdown. This is currently pushed out
into fabric modules as current fabric code may sleep here waiting for
TFO->check_stop_free() to complete in main response path, and because
target_wait_for_sess_cmds() calling TFO->release_cmd() to free fabric
descriptor memory directly.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
The commit
target: use a workqueue for I/O completions
accidentally removed setting t_tasks_failed in transport_complete_task.
Add it back in a slightly cleaner way; now it is set for every failed task
instead of special casing the last one completing by using the success
argument directly for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
The check is wrong here because blk_make_request() returns an
ERR_PTR() and it doesn't return NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch drops TRANSPORT_FREE_CMD_INTR usage from target core, which
includes the removal of transport_generic_free_cmd_intr() symbol,
TRANSPORT_FREE_CMD_INTR usage in transport_processing_thread(), and
special case LUN_RESET handling to skip TRANSPORT_FREE_CMD_INTR processing
in core_tmr_drain_cmd_list(). We now expect that fabric modules will
use an internal workqueue to provide process context when releasing
se_cmd descriptor resources via transport_generic_free_cmd().
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Madhuranath Iyengar <mni@risingtidesystems.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch converts target_core_fabric_ops->check_stop_free() usage in
transport_cmd_check_stop() and associated fabric module usage to
return '1' when the passed se_cmd has been released directly within
->check_stop_free(), or return '0' when the passed se_cmd has not
been released.
This addresses an issue where transport_cmd_finish_abort() ->
transport_cmd_check_stop_to_fabric() was leaking descriptors during
LUN_RESET for modules using ->check_stop_free(), but not directly
releasing se_cmd in all cases.
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch addresses two issues with non immediate TMR handling in
iscsit_handle_task_mgt_cmd(). The first involves breakage due to
v3.1-rc conversion of iscsit_sequence_cmd(), which upon good status
would hit the iscsit_add_reject_from_cmd() block of code. This patch
adds an explict check for CMDSN_ERROR_CANNOT_RECOVER.
The second adds a check to return when non immediate TMR operation is
detected after iscsit_ack_from_expstatsn(), as iscsit_sequence_cmd()
-> iscsit_execute_cmd() will have called transport_generic_handle_tmr()
for the non immediate TMR case already.
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a missing CMDSN_LOWER_THAN_EXP return check for
iscsit_sequence_cmd() in iscsit_handle_scsi_cmd() that was incorrectly
dropped during the v3.1-rc cleanups to use iscsit_sequence_cmd().
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
After the list_del() in core_tmr_drain_tmr_list(),
core_tmr_release_req() would list_del() the same object again.
Call graph:
core_tmr_drain_tmr_list
transport_cmd_finish_abort_tmr
transport_generic_remove
transport_free_se_cmd
core_tmr_release_req
So use list_del_init(), as list_del() of an initialized list_head is
safe and essentially a nop. In the CONFIG_DEBUG_LIST case, list_del()
actually poisons the list_head, but that is fine as we free the object
directly afterwards.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch adds a handful minor cleanups to core_tmr_drain_tmr_list() that
remove an unnecessary NULL check, use list_for_each_entry_safe() instead of
list_entry(), and makes the drain_tmr_list walk use *tmr_p instead of
directly referencing the passed *tmr function parameter.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Joern Engel <joern@logfs.org>
Reviewed-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes another bug from LUN_RESET re-org fallout in
core_tmr_drain_tmr_list() that was adding the wrong se_tmr_req
into the local drain_tmr_list to be walked + released.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Joern Engel <joern@logfs.org>
Reviewed-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in core_tmr_drain_tmr_list() where drain_tmr_list
was using the wrong se_tmr_req for cmd assignment due to a typo during the
LUN_RESET re-org. This was resulting in general protection faults while
using the leftover bogus *tmr_p pointer from list_for_each_entry_safe().
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Joern Engel <joern@logfs.org>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes target core to also check for -ENOMEM from fabric callbacks
to signal QUEUE_FULL status, instead of just -EAGAIN in order to catch a
larger set of fabric failure cases that want to trigger QUEUE_FULL logic.
This includes the callbacks for ->write_pending(), ->queue_data_in() and
->queue_status().
It also makes transport_generic_write_pending() return zero upon QUEUE_FULL,
and removes two unnecessary -EAGAIN checks to catch write pending QUEUE_FULL
cases from transport_generic_new_cmd() failures in transport_handle_cdb_direct()
and transport_processing_thread():TRANSPORT_NEW_CMD_MAP state.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch addresses an issue with buggy userspace code sending I/O
via scsi-generic that does not explictly clear their associated read
buffers. It adds an explict memset of the first SGL entry within
tcm_loop_new_cmd_map() for SCF_SCSI_CONTROL_SG_IO_CDB payloads that
are currently guaranteed to be a single SGL by target-core code.
This issue is a side effect of the v3.1-rc1 merge to remove the
extra memcpy between certain control CDB types using a contigious
+ cleared buffer in target-core, and performing a memcpy into the
SGL list within tcm_loop.
It was originally mainfesting itself by udev + scsi_id + scsi-generic
not properly setting up the expected /dev/disk/by-id/ symlinks because
the INQUIRY payload was containing extra bogus data preventing the
proper NAA IEEE WWN from being parsed by userspace.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the following compile warning in target_core_cdb.c in
recent linux-next code due to the new use of EXPORT_SYMBOL() for
target_get_task_cdb().
drivers/target/target_core_cdb.c:1316: warning: data definition has no type or storage class
drivers/target/target_core_cdb.c:1316: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
drivers/target/target_core_cdb.c:1316: warning: parameter names (without types) in function declaration
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (62 commits)
target: Fix compile warning w/ missing module.h include
target: Remove legacy se_task->task_timer and associated logic
target: Fix incorrect transport_sent usage
target: re-use the command S/G list for single-task commands
target: Fix BIDI t_task_cdb handling in transport_generic_new_cmd
target: remove transport_allocate_tasks
target: merge transport_new_cmd_obj into transport_generic_new_cmd
target: remove the task_sg_bidi field se_task and pSCSI BIDI support
target: transport_subsystem_check_init cleanups
target: use a workqueue for I/O completions
target: remove unused TRANSPORT_ states
target: remove TRANSPORT_DEFERRED_CMD state
target: remove the TRANSPORT_REMOVE state
target: move depth_left manipulation out of transport_generic_request_failure
target: stop task timers earlier
target: remove TF_TIMER_STOP
target: factor some duplicate code for stopping a task
target: fix list walking in transport_free_dev_tasks
target: use transport_cmd_check_stop_to_fabric consistently
target: do not pass the queue object to transport_remove_cmd_from_queue
...
* 'next' of git://selinuxproject.org/~jmorris/linux-security: (95 commits)
TOMOYO: Fix incomplete read after seek.
Smack: allow to access /smack/access as normal user
TOMOYO: Fix unused kernel config option.
Smack: fix: invalid length set for the result of /smack/access
Smack: compilation fix
Smack: fix for /smack/access output, use string instead of byte
Smack: domain transition protections (v3)
Smack: Provide information for UDS getsockopt(SO_PEERCRED)
Smack: Clean up comments
Smack: Repair processing of fcntl
Smack: Rule list lookup performance
Smack: check permissions from user space (v2)
TOMOYO: Fix quota and garbage collector.
TOMOYO: Remove redundant tasklist_lock.
TOMOYO: Fix domain transition failure warning.
TOMOYO: Remove tomoyo_policy_memory_lock spinlock.
TOMOYO: Simplify garbage collector.
TOMOYO: Fix make namespacecheck warnings.
target: check hex2bin result
encrypted-keys: check hex2bin result
...
This patch fixes the following compile warning in target_core_cdb.c in
recent linux-next code due to the new use of EXPORT_SYMBOL() for
target_get_task_cdb().
drivers/target/target_core_cdb.c:1316: warning: data definition has no type or storage class
drivers/target/target_core_cdb.c:1316: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
drivers/target/target_core_cdb.c:1316: warning: parameter names (without types) in function declaration
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes the legacy usage of se_task->task_timer and associated
infrastructure that originally was used as a way to help manage buggy backend
SCSI LLDs that in certain cases would never return back an outstanding task.
This includes the removal of target_complete_timeout_work(), timeout logic
from transport_complete_task(), transport_task_timeout_handler(),
transport_start_task_timer(), the per device task_timeout configfs attribute,
and all task_timeout associated structure members and defines in
target_core_base.h
This is being removed in preparation to make transport_complete_task() run
in lock-less mode.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts target-core to use se_cmd->t_transport_sent instead of
a duplicated se_cmd->transport_sent member in a handful of locations.
It also updates iscsi_target to properly use ->t_transport_sent instead of
it's own iscsi_cmd_t->transport_sent value that was not being assigned.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If we only have a single task per command (which at least in my testing
is the by far most common case) we do not have to allocate a new per-task
S/G list but can reuse the one from the command.
(nab: Fix BIDI handling in transport_free_dev_tasks)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug for BIDI handling in transport_generic_new_cmd() where
cmd->t_task_cdbs_left and Co. where not taking into account the extra
task count generated during the first call to transport_allocate_data_tasks().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There were only two callers, and one of them always wants the call
to transport_allocate_data_tasks anyway. Also drop the constant
lba argument to transport_allocate_data_tasks and move the variables
inside it into the minimum required scope.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
These are two fairly small functions, and merging them gives a much
more readable control flow, and opportunities for more useful comments.
It also moves all code related to resources allocation closer together
and allows to remove a forward declaration for transport_allocate_tasks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This field is never used given that BIDI handling happens at the
command and not the task level. Remove it and the dead code in
pscsi that tries to work on it.
It also prevents pSCSI passthrough for the two currently enabled BIDI
commands now that task->task_sg_bidi support has been removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the now unnecessary extra call to transport_subsystem_check_init() in
target_core_register_fabric(), and also merge transport_subsystem_reqmods()
directly into transport_subsystem_check_init().
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of abusing the target processing thread for offloading I/O
completion in the backends to user context add a new workqueue. This means
completions can be processed as fast as available CPU time allows it,
including in parallel with other completions and more importantly I/O
submission or QUEUE FULL retries. This should give much better performance
especially on loaded systems.
As a fallout we can merge all the completed states into a single
one.
On the downside this change complicates lun reset handling a bit by
requiring us to cancel a work item only for those states that have it
initialized. The alternative would be to either always initialize the work
item to a dummy handler, or always use the same handler and do a switch on
the state. The long term solution will be a flag that says that the command
has an initialized work item, but that's only going to be useful once we
have more users.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We never check for this state, and it makes testing for a completed
state much harder given that it overrides the existing state.
Also remove the unused deferred_t_state which is related to it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We never queue an command with this state, and only set it in a completely
bogus place in tcm_fc.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We only need to decrement dev->depth_left if failing a command from
__transport_execute_tasks. Instead of doing it first thing in
transport_generic_request_failure and requiring a pseudo-flag argument
for it just opencode the decrement in the two callers (which should
be factored into a single one anyway)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently we stop the timers for all tasks in a command fairly late during
I/O completion, which is fairly pointless and requires all kinds of safety
checks.
Instead delete pending timers early on in transport_complete_task, thus
ensuring no new timers firest after that. We take t_state_lock a bit later
in that function thus making sure currenly running timers are out of the
criticial section. To be completely sure the timer has finished we also
add another del_timer_sync call when freeing the task.
This also allows removing TF_TIMER_RUNNING as it would be equivalent
to TF_ACTIVE now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
TF_TIMER_STOP is useless as it only helps to mitigate a tiny race during
deleting the timer. But given that we have cleared TF_ACTIVE at this point
we already have another mitigation a few lines down the function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
list_for_each_entry_safe only protects against deletions from the list,
but not against any concurrent modifications. Given that we drop
t_state_lock inside the loop it is not safe in transport_free_dev_tasks.
Instead of use a local dispose_list that we move all tasks that are
to be deleted to. This is safe because we never do list_emptry checks
on t_list to check if a command is on the list anywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Change one remaining user of transport_cmd_check_stop(cmd, 2, 0) to the
transport_cmd_check_stop_to_fabric wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We always operated on the same queue, so move finding it into the function,
just like we do for all other helpers operating on it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add a new boolean at_head parameter to transport_add_cmd_to_queue and thus
obsolete the SCF_EMULATE_QUEUE_FULL flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the need for the transport_qf_callback callback by making
sure we have specific states with specific handlers for the two
queue full cases.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the dpo_emulated, fua_write_emulated, fua_read_emulated and
write_cache_emulated methods, and replace them with a simple bitfields in
se_subsystem_api in those cases where they ever returned one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Do not block the submitting thread when handling a SYNCHRONIZE CACHE command,
but implement it asynchronously by sending the FLUSH command ourself and
calling transport_complete_sync_cache from the completion handler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug with the handling of REPORT TARGET PORT GROUPS
containing a smaller allocation length than the payload requires causing
memory writes beyond the end of the buffer. This patch checks for the
minimum 4 byte length for the response payload length, and also checks
upon each loop of T10_ALUA(su_dev)->tg_pt_gps_list to ensure the Target
port group and Target port descriptor list is able to fit into the
remaining allocation length.
If the response payload exceeds the allocation length length, then rd_len
is still increments to indicate to the initiator that the payload has
been truncated.
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
Add a switch statement implementing the CDB LBA/len update directly
in target_get_task_cdb and remove the old ->transport_split_cdb
callback and all its implementations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of calling out to the backends from the core to get a per-task
CDB and then modify it for the LBA/len pair used for this CDB provide
a helper that writes the adjusted CDB into a provided buffer and call
this method from ->do_task in pscsi.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The most commonly used file, iblock and rd backends have no use for
a per-task CDB and thus don't need a method to copy it into their
otherwise unused CDB fields.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is a squashed version of the following unnecessary se_task structure
member removal patches:
target: remove the task_execute_queue field in se_task
Instead of using a separate flag we can simply do list_emptry checks
on t_execute_list if we make sure to always use list_del_init to remove
a task from the list. Also factor some duplicate code into a new
__transport_remove_task_from_execute_queue helper.
target: remove the read-only task_no field in se_task
The task_no field never was initialized and only used in debug printks,
so kill it.
target: remove the task_padded_sg field in se_task
This field is only check in one place and not actually needed there.
Rationale:
- transport_do_task_sg_chain asserts that we have task_sg_chaining
set early on
- we only make use of the sg_prev_nents field we calculate based on it
if there is another sg list that gets chained onto this one, which
never happens for the last (or only) task.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Replace various atomic_t variables that were mostly under t_state_lock
with new flags in task_flags. Note that the execution error path
didn't take t_state_lock before, so add it there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is a squashed version of the following se_task cleanup patches:
target: remove the unused task_state_flags field in se_task
target: remove the unused se_obj_ptr field in se_task
target: remove the se_dev field in se_task
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is a squashed version of the following target_core_base.h
cleanup patches:
target: remove the unused SHUTDOWN_SIGS defintion
target: remove unused se_mem leftovers
target: remove the unused map_func_t typedef
target: move TRANSPORT_IOV_DATA_BUFFER to the iscsi-specific code
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes the legacy device active I/O shutdown code that was
originally called from transport_processing_thread() context during shutdown
including transport_processing_shutdown() and transport_release_all_cmds().
This is due to the fact that in modern configfs control plane code by the
time shutdown of an se_device instance in transport_processing_thread()
is allowed to occur via:
rmdir /sys/kernel/config/target/core/$HBA/$DEV
all active I/O will already have been ceased while removing active configfs
fabric Port/LUN symlinks. Eg: the removal of an active se_device is protected
by inter-module VFS references from active Port/LUN symlinks.
Two WARN_ON() checks have been added in their place before exiting
transport_processing_thread() to watch out for any leaked descriptors.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch merges transport_cmd_finish_abort_tmr() logic into a single
transport_cmd_finish_abort() function by adding a cmd->se_tmr_req check
around transport_lun_remove_cmd(), and updates the single caller within
core_tmr_drain_tmr_list().
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes a number of SCF_SE_LUN_CMD flag abuses within iscsi-target
code to determine when iscsit_release_cmd() or transport_generic_free_cmd()
should be called while releasing an individual iscsi_cmd descriptor.
In the place of SCF_SE_LUN_CMD checks, this patch converts existing code to
use a new iscsit_free_cmd() that inspects iscsi_cmd->iscsi_opcode types to
determine which of the above functions should be invoked. It also removes the
now unnecessary special case checking in iscsit_release_commands_from_conn().
(hch: Use iscsit_free_cmd instead of open-coded alternative)
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts se_cmd->transport_wait_for_tasks(se_cmd, 1) usage to use
transport_generic_free_cmd() directly in target-core and iscsi-target fabric
usage. The includes:
*) Removal of the optional transport_generic_free_cmd() call from within
transport_generic_wait_for_tasks()
*) Usage of existing SCF_SUPPORTED_SAM_OPCODE to determine when
transport_generic_wait_for_tasks() processing may occur instead of
checking se_cmd->transport_wait_for_tasks()
*) Move transport_generic_wait_for_tasks() call ahead of core_dec_lacl_count()
and transport_lun_remove_cmd() in transport_generic_free_cmd() to follow
existing logic for iscsi-target w/ se_cmd->transport_wait_for_tasks(se_cmd, 1)
*) Removal of se_cmd->transport_wait_for_tasks() function pointer
*) Rename transport_generic_wait_for_tasks() -> transport_wait_for_tasks(), and
add docbook comment.
*) Add EXPORT_SYMBOL for transport_wait_for_tasks()
For the case in iscsi_target_erl2.c:iscsit_prepare_cmds_for_realligance()
where se_cmd->transport_wait_for_tasks(se_cmd, 0) is called, this patch
adds a direct call to transport_wait_for_tasks().
(hch: Fix transport_generic_free_cmd() usage in iscsit_release_commands_from_conn)
(nab: Add patch: Ensure that TMRs hit wait_for_tasks logic during release)
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Testing in_interrupt() to know when sleeping is allowed is not really
reliable (since eg it won't be true if the caller is holding a spinlock).
Instead have the caller tell core_tmr_alloc_req() what GFP_xxx to use;
every caller except tcm_qla2xxx can use GFP_KERNEL.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes pscsi_create_virtdevice() to properly return ERR_CAST
instead of a raw pointer upon scsi_host_lookup() failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts ft_parse_wwn() to use hex_to_bin() instead of custom
conversion code.
(Andy: Re-add missing strict && isupper(c) check)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts chap_string_to_hex() to use hex2bin() instead of
the internal chap_asciihex_to_binaryhex().
(nab: Fix up minor compile breakage + typo)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The cdb_none, map_data_SG and map_control_SG methods have no callers left
and can be removed now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move the entirely request allocation, mapping and submission into ->do_task.
This
a) avoids blocking the I/O submission thread unessecarily, and
b) simplifies the code greatly
Note that the code seems to have various error handling issues, mostly
related to bidi handling in the current form. I've added comments about
those but not tried to fix them in this commit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move the entirely bio allocation, mapping and submission into ->do_task.
This
a) avoids blocking the I/O submission thread unessecarily, and
b) simplifies the code greatly
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a minor simplfication in target_parse_naa_6h_vendor_specific()
to remove direct isxdigit() + ctype.h usage.
(nab: Fix next assignment breakage in for loop)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes the unnecessary session_reinstatement parameter from
se_cmd->transport_wait_for_tasks(), logic in transport_generic_wait_for_tasks,
and usage within iscsi-target code.
This also includes the removal of the 'bool' return from transport_put_cmd() +
transport_generic_free_cmd() that is no longer necessary.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Push session reinstatement out of transport_generic_free_cmd into the only
caller that actually needs it. Clean up transport_generic_free_cmd a bit,
and remove the useless comment. I'd love to add a more useful kerneldoc
comment for it, but as this point I'm still a bit confused in where it
stands in the command release stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All callers that never have the session_reinstatement flag set can trivially
be converted to transport_put_cmd. Opencode the session reinstatement code
in transport_generic_free_cmd, which was the only caller ever asking for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Inline two simple functions only used by it, and replace a goto
with a simple if else construct.
Note that the code moved from transport_dec_and_check seems fairly
buggy - the atomic_read check on a variable where we'd do an
atomic_dec_and_test looks racy if we'll ever get someone increment
it without the lock held around them (which it looks like we do),
and not decrementing the second counter if the first one doesn't
hit zero also at least needs an explanation.
(nab: Fix transport_put_cmd breakage)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of duplicating the code from transport_release_fe_cmd re-use it by
allowing transport_release_fe_cmd to return wether it actually freed the
command or not. Also rename transport_release_fe_cmd to transport_put_cmd
and add a kerneldoc comment for it to make the use case more obvious.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It is only called by transport_release_cmd, so inline it there. Also add
a kerneldoc comment for transport_release_cmd while we are at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iscsit_task_reassign_complete is always called from the TX thread, so
handle the CDB directly instead of offloading it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
ft_send_work is always called from workqueue context, which means we can
handle the CDB directly instead of doing another context switch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where transport_send_task_abort() could be called
during LUN_RESET to return SAM_STAT_TASK_ABORTED + tfo->queue_status(), when
SCF_SENT_CHECK_CONDITION -> tfo->queue_status() has already been sent from
within another context via transport_send_check_condition_and_sense().
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch fixes a bug in LUN_RESET operation with transport_cmd_finish_abort()
where transport_remove_cmd_from_queue() was incorrectly being called, causing
descriptors with t_state == TRANSPORT_FREE_CMD_INTR to be incorrectly removed
from qobj->qobj_list during process context release. This change ensures the
descriptor is only removed via transport_remove_cmd_from_queue() when doing a
direct release via transport_generic_remove().
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch contains a bugfix for TMR LUN_RESET related to TRANSPORT_FREE_CMD_INTR
operation, where core_tmr_drain_cmd_list() will now skip processing for this
case to prevent an ABORT_TASK status from being returned for descriptors that
are already queued up to be released by processing thread context.
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch is a re-orginzation of core_tmr_lun_reset() logic to properly
scan the active tmr_list, dev->state_task_list and qobj->qobj_list w/ the
relivent locks held, and performing a list_move_tail onto seperate local
scope lists before performing the full drain.
This involves breaking out the code into three seperate list specific
functions: core_tmr_drain_tmr_list(), core_tmr_drain_task_list() and
core_tmr_drain_cmd_list().
(nab: Include target: Remove non-active tasks from execute list during
LUN_RESET patch to address original breakage)
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch addresses a bug with the lio-core-2.6.git conversion of
transport_add_cmd_to_queue() to use a single embedded list_head, instead
of individual struct se_queue_req allocations allowing a single se_cmd to
be added to the queue mulitple times. This was changed in the following:
commit 2a9e4d5ca5d99f4c600578d6285d45142e7e5208
Author: Andy Grover <agrover@redhat.com>
Date: Tue Apr 26 17:45:51 2011 -0700
target: Embed qr in struct se_cmd
The problem is that some target code still assumes performing multiple
adds is allowed via transport_add_cmd_to_queue(), which ends up causing
list corruption in qobj->qobj_list code. This patch addresses this
by removing an existing struct se_cmd from the list before the add, and
removes an unnecessary list walk in transport_remove_cmd_from_queue()
It also changes cmd->t_transport_queue_active to use explict sets intead
of increment/decrement to prevent confusion during exception path handling.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/target/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that hex2bin does error checking, on error add debugging error msg.
Changelog v1 (update):
- fixed definition of 'ret'
- hex2bin now returns an int
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
This patch fixes a bug in the iscsit_fe_sendpage_sg() transmit codepath that
was originally introduced with the v3.1 iscsi-target merge that incorrectly
uses hardcoded cmd->iov_data_count values to determine cmd->iov_data[] offsets
for extra outgoing padding and DataDigest payload vectors.
This code is obviously incorrect for the DataDigest enabled case with sendpage
offload, and this fix ensures correct operation for padding + DataDigest,
padding only, and DataDigest only cases. The bug was introduced during a
pre-merge change in iscsit_fe_sendpage_sg() to natively use struct scatterlist
instead of the legacy v3.0 struct se_mem logic.
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes iscsi-target explictly disable OFMarker=Yes and IFMarker=yes
parameter key usage during iscsi login by setting IFMarkInt_Reject and
OFMarkInt_Reject values in iscsi_enforce_integrity_rules() to effectively
disable iscsi marker usage. With this patch, an initiator proposer asking
to enable either marker parameter keys will be issued a 'No' response, and
the target sets OFMarkInt + IFMarkInt parameter key response to 'Irrelevant'.
With markers disabled during iscsi login, this patch removes the problematic
on-stack local-scope array for marker intervals in iscsit_do_rx_data() +
iscsit_do_tx_data(), and other related marker code in iscsi_target_util.c.
This fixes a potentional stack smashing scenario with small range markers
enabled and a large MRDSL as reported by DanC here:
[bug report] target: stack can be smashed
http://www.spinics.net/lists/target-devel/msg00453.html
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds target_parse_naa_6h_vendor_specific() to address a bug where the
conversion of PRODUCT SERIAL NUMBER to use hex2bin() in target_emulate_evpd_83()
was not doing proper isxdigit() checking. This conversion of the vpd_unit_serial
configifs attribute is done while generating a VPD=0x83 NAA IEEE Registered
Extended DESIGNATOR format's 100 bits of unique VENDOR SPECIFIC IDENTIFIER +
VENDOR SPECIFIC IDENTIFIER EXTENSION area.
This patch allows vpd_unit_serial (VPD=0x80) and the T10 Vendor ID DESIGNATOR
format (VPD=0x83) to continue to use free-form variable length ASCII values,
and now skips any non hex characters for fixed length NAA IEEE Registered Extended
DESIGNATOR format (VPD=0x83) requring the binary conversion.
This was originally reported by Martin after the v3.1-rc1 change to use hex2bin()
in commit 11650b8596 where the use of non hex
characters in vpd_unit_serial generated different values than the original
v3.0 internal hex -> binary code. This v3.1 change caused a problem with
filesystems who write a NAA DESIGNATOR onto it's ondisk metadata, and this patch
will (again) change existing values to ensure that non hex characters are not
included in the fixed length NAA DESIGNATOR.
Note this patch still expects vpd_unit_serial to be set via existing userspace
methods of uuid generation, and does not do strict formatting via configfs input.
The original bug report and thread can be found here:
NAA breakage
http://www.spinics.net/lists/target-devel/msg00477.html
The v3.1-rc1 formatting of VPD=0x83 w/o this patch:
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 20
designator_type: NAA, code_set: Binary
associated with the addressed logical unit
NAA 6, IEEE Company_id: 0x1405
Vendor Specific Identifier: 0xffde35ebf
Vendor Specific Identifier Extension: 0x3092f498ffa820f9
[0x6001405ffde35ebf3092f498ffa820f9]
Designation descriptor number 2, descriptor length: 56
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: LIO-ORG
vendor specific: IBLOCK:ffde35ec-3092-4980-a820-917636ca54f1
The v3.1-final formatting of VPD=0x83 w/ this patch:
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 20
designator_type: NAA, code_set: Binary
associated with the addressed logical unit
NAA 6, IEEE Company_id: 0x1405
Vendor Specific Identifier: 0xffde35ec3
Vendor Specific Identifier Extension: 0x924980a82091763
[0x6001405ffde35ec30924980a82091763]
Designation descriptor number 2, descriptor length: 56
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: LIO-ORG
vendor specific: IBLOCK:ffde35ec-3092-4980-a820-917636ca54f1
(v2: Fix parsing code to dereference + check for string terminator instead
of null pointer to ensure a zeroed payload for vpd_unit_serial less
than 100 bits of NAA DESIGNATOR VENDOR SPECIFIC area. Also, remove
the unnecessary bitwise assignment)
Reported-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Problem: Changed from wake_up_interruptible -> wake_up_process and
wait_event_interruptible-> schedule_timeout_interruptible broke the FCoE
target. Earlier approach of wake_up_interruptible was also looking at
'queue_cnt' which is not necessary, because it increment of 'queue_cnt'
with wake_up_inetrriptible / waker_up_process introduces race condition.
Fix: Instead of fixing the code which used wake_up_process and remove
'queue_cnt', using work_queue based approach is cleaner and acheives
same result. As well, work queue based approach has less programming
overhead and OS manages threads which processes work queues.
This patch is developed by Christoph Hellwig and reviwed+validated by
Kiran Patil.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Problem: HW DDP context wasn;t invalidated in case of ABORTS, etc...
This leads to the problem where memory pages which are used for DDP
as user descriptor could get reused for some other purpose (such as to
satisfy new memory allocation request either by kernel or user mode threads)
and since HW DDP context was not invalidated, HW continue to write to
those pages, hence causing memory corruption.
Fix: Either on incoming ABORTS or due to exchange time out, allowed the
target to cleanup HW DDP context if it was setup for respective ft_cmd.
Added new function to perform this cleanup, furthur it can be enhanced
for other cleanup activity.
Additinal Notes: To avoid calling ddp_done from multiple places, composed
the functionality in helper function "ft_invl_hw_context" and it is being
called from multiple places. Cleaned up code in function "ft_recv_write_data"
w.r.t DDP.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When work is scheduled with schedule_work(), the work can end up
running on multiple CPUs at the same time -- this happens if
the work is already running on one CPU and schedule_work() is called
on another CPU. This leads to list corruption with target_qf_do_work(),
which is roughly doing:
spin_lock(...);
list_for_each_entry_safe(...) {
list_del(...);
spin_unlock(...);
// do stuff
spin_lock(...);
}
With multiple CPUs running this code, one CPU can end up deleting the
list entry that the other CPU is about to work on.
Fix this by splicing the list entries onto a local list and then
operating on that in the work function. This way, each invocation of
target_qf_do_work() operates on its own local list and so multiple
invocations don't corrupt each other's list. This also avoids dropping
and reacquiring the lock for each list entry.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/target/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With qla2xxx, acl_node_lock is taken inside qla2xxx's hardware_lock,
which is taken in hardirq context. This means acl_node_lock must become
an IRQ-disabling lock; in particular this fixes lockdep warnings along
the lines of
======================================================
[ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ]
(&(&se_tpg->acl_node_lock)->rlock){+.....}, at: [<ffffffffa026f872>] transport_deregister_session+0x92/0x140 [target_core_mod]
and this task is already holding:
(&(&ha->hardware_lock)->rlock){-.-...}, at: [<ffffffffa017c5e7>] qla_tgt_stop_phase1+0x57/0x2c0 [qla2xxx]
which would create a new lock dependency:
(&(&ha->hardware_lock)->rlock){-.-...} -> (&(&se_tpg->acl_node_lock)->rlock){+.....}
but this new dependency connects a HARDIRQ-irq-safe lock:
(&(&ha->hardware_lock)->rlock){-.-...}
to a HARDIRQ-irq-unsafe lock:
(&(&se_tpg->acl_node_lock)->rlock){+.....}
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
At least the tcm_qla2xxx fabric driver calls into transport_deregister_session()
while holding an IRQ-disabled spinlock, so the inner locking needs to
use spin_lock_irqsave() instead of spin_lock_bh().
This fixes warnings seen with tcm_qla2xxx like:
WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x98/0xb0()
Call Trace:
[<ffffffff8104e65f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8104e6ba>] warn_slowpath_null+0x1a/0x20
[<ffffffff81055368>] local_bh_enable_ip+0x98/0xb0
[<ffffffff814d5284>] _raw_spin_unlock_bh+0x14/0x20
[<ffffffffa027b7f6>] transport_deregister_session+0x96/0x180 [target_core_mod]
[<ffffffffa00f7731>] tcm_qla2xxx_free_session+0xd1/0x170 [tcm_qla2xxx]
[<ffffffffa01b9173>] qla_tgt_sess_put+0xc3/0x140 [qla2xxx]
[<ffffffffa01bf40f>] qla_tgt_stop_phase1+0x8f/0x2c0 [qla2xxx]
[<ffffffffa00f735e>] tcm_qla2xxx_tpg_store_enable+0x6e/0xd0 [tcm_qla2xxx]
[<ffffffffa026ca29>] target_fabric_tpg_attr_store+0x39/0x40 [target_core_mod]
[<ffffffffa00a575d>] configfs_write_file+0xbd/0x120 [configfs]
[<ffffffff811464a6>] vfs_write+0xc6/0x180
[<ffffffff811467c1>] sys_write+0x51/0x90
[<ffffffff814dd382>] system_call_fastpath+0x16/0x1b
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There's no need for the #ifdef protection when building into the kernel,
and in fact we need the module_init() for the initialization function to
be called.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make a log message more useful by printing both the page and subpage
that an initiator is requesting.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes two bugs in allocation failure handling in
iscsit_allocate_se_cmd_for_tmr():
This first reported by DanC is a free-after call to transport_free_se_cmd(), this
patch drops the transport_free_se_cmd() call all together, as iscsit_release_cmd()
will release existing allocations as expected.
The second is a bug where iscsi_cmd_t was being leaked on a cmd->tmr_req allocation
failure, so make this jump to iscsit_release_cmd() as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The iSCSI target configfs code to print out an initiator's IPv6 address
is not fully implemented. This patch uses snprintf() with the "%pI6c"
format string to format the IPv6 address for display purposes.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes two bugs associated with transport_do_task_sg_chain()
operation where transport_allocate_data_tasks() was incorrectly setting
task_padded_sg for all tasks, and causing bogus task->task_sg_nents
assignments + OOPsen with fabrics depending upon this code. The first bit
here adds a task_sg_nents_padded check in transport_allocate_data_tasks()
to include an extra SGL vector when necessary for tasks that expect to
be linked using sg_chain().
The second change involves making transport_do_task_sg_chain() properly
account for the extra SGL vector when task->task_padded_sg is set for
the non trailing ->task_sg or single ->task_sg allocations. Note this
patch also removes the BUG_ON(!task->task_padded_sg) check within
transport_do_task_sg_chain() as we expect this to happen normally
with the updated logic in transport_allocate_data_tasks(), along with
being bogus for CONTROL_SG_IO_CDB type payloads.
So far this bugfix has been tested with tcm_qla2xxx and iblock backends
in (task_count > 1)( and (task_count == 1) operation.
Reported-by: Kiran Patil <kiran.patil@intel.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses recent breakage with multiple se_task (task_count > 1)
operation following backend dev->se_sub_dev->se_dev_attrib.max_sectors in new
transport_allocate_data_tasks() code. The initial bug here was a bogus
task->task_sg_nents assignment in transport_allocate_data_tasks() based on
the passed parameter, which now uses DIV_ROUND_UP(task_size, PAGE_SIZE) to
determine the proper number of per task SGL entries for the (task_count > 1)
case.
This also means we now need to enforce a PAGE_SIZE aligned max_sector count
value for this to work as expected without bringing back the pre v3.1
transport_map_mem_to_sg() logic to handle SGL offsets across multiple tasks.
So this patch adds se_dev_align_max_sectors() to round down max_sectors as
necessary to ensure this alignment via se_dev_set_default_attribs() and
se_dev_align_max_sectors() and keeps it simple for (task_count > 1)
operation.
So far this bugfix has been tested with (task_count > 1) operation
using iscsi-target and iblock backends.
Reported-by: Chris Boot <bootc@bootc.net>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the missing transport_cmd_get_valid_sectors() check for
SCF_SCSI_DATA_SG_IO_CDB type payloads to ensure that a received LBA + range
does not exeed past the end of associated backend struct se_device.
This patch also fixes a bug in the failure path of transport_new_cmd_obj()
where this check can fail, so change to use a signed 'rc' and return '-EINVAL'
to signal proper transport_generic_request_failure() handling.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a SYNCHRONIZE_CACHE CDB handling bug with IBLOCK/FILEIO
backends where transport_cmd_get_valid_sectors() was incorrectly rejecting
a zero LBA + range CDB from being processed, and returning CHECK_CONDITION.
This includes changing transport_cmd_get_valid_sectors() to return '0' on
success and '-EINVAL' on failure (this makes more sense than sectors),
and to only check transport_cmd_get_valid_sectors() when a non zero LBA +
range SYNCHRONIZE_CACHE operation has been receieved for the non passthrough
case.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes a duplicate set of transport_complete_task() calls in
target_emulate_unmap() and target_emulate_write_same() as the completion
call is already done within transport_emulate_control_cdb()
This patch also adds a check in transport_emulate_control_cdb() for the
existing SCF_EMULATE_CDB_ASYNC flag currently used by SYNCHRONIZE_CACHE
in order to handle IMMEDIATE processing.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For all flavours of WRITE_SAME, we only expect to handle a single block
of data-out buffer payload, regardless of the number of logical blocks
presented in the CDB. This patch changes all flavours of WRITE_SAME in
transport_generic_cmd_sequencer() to pass '1' into transport_get_size()
instead of the extracted 'sectors' to properly handle the default usage
of sg_write_same without the --xferlen parameter.
Reported-by: Eric Seppanen <eric@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch adds initial WRITE_SAME (10) w/ UNMAP=1 support following updates in
sbcr26 to allow UNMAP=1 for the non 16 + 32 byte CDB case. It also refactors
current pSCSI passthrough passthrough checks into target_check_write_same_discard()
ahead of UNMAP=0 w/ write payload support into target_core_iblock.c.
This includes the support for handling WRITE_SAME in transport_emulate_control_cdb(),
and converts target_emulate_write_same to accept num_blocks directly for
WRITE_SAME, WRITE_SAME_16 and WRITE_SAME_32.
Reported-by: Eric Seppanen <eric@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch fixes a bug for fabrics using tfo->new_cmd_map() that
are expect transport_generic_request_failure() to be calling
transport_send_check_condition_and_sense() for both READ and WRITE,
instead of only for READ exceptions.
This was originally observed with a failed WRITE_SAME_16 w/ unmap=0
using tcm_loop.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a forever loop bug in iscsit_attach_ooo_cmdsn()
while walking sess->sess_ooo_cmdsn_list when the received
CmdSN is less than the tail of the list.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use BUG_ON(x) rather than if(x) BUG();
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ identifier x; @@
-if (x) BUG();
+BUG_ON(x);
@@ identifier x; @@
-if (!x) BUG();
+BUG_ON(!x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We leak memory if the allocations for 'new_param->name' or
'new_param->value' fail in iscsi_target_parameters.c::iscsi_copy_param_list()
We also do a lot of variable assignments that are completely pointless
if the allocations fail.
So, let's move the allocations before the assignments and also make
sure that we free whatever was allocated to one if the allocation fail.
There's also some small CodingStyle fixups in there (curly braces on
both branches of if statement, only one variable per line) since I was
in the area anyway. And finally, error messages in the function are
put on a single line for easy grep'abillity.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
The semantic patch that makes this output is available
in scripts/coccinelle/api/err_cast.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes target_emulate_inquiry_std() to set the 'not connected'
(0x35) bit in standard INQUIRY response data when we are processing a
request to a virtual LUN=0 mapping from struct se_device *g_lun0_dev that
have been setup for us in transport_lookup_cmd_lun().
This addresses an issue where qla2xxx FC clients need to be able
to create demo-mode I_T FC Nexuses by default, but should not be
exposing the default set of TPG LUNs to all FC clients. This includes
adding an new optional target_core_fabric_ops->tpg_check_demo_mode_login_only()
caller to allow demo_mode nexuses to skip the old default of bulding
a demo-mode MappedLUNs list via core_tpg_add_node_to_devs().
(roland: Add missing tpg_check_demo_mode_login_only check in core_dev_add_lun)
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch changes transport_send_check_condition_and_sense() for
TCM_NON_EXISTENT_LUN emulation to use 0x25 (LOGICAL UNIT NOT SUPPORTED)
instead of the original 0x20 (INVALID COMMAND OPERATION CODE). This is
helpful to distinguish between TCM_UNSUPPORTED_SCSI_OPCODE ASC=0x20
exceptions.
Signed-off-by: Nicholas A. Bellinger <nab@risingtidesystems.com>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data
target: Fix bug for transport_generic_wait_for_tasks with direct operation
target: iscsi_target depends on NET
target: Fix WRITE_SAME_16 lba assignment breakage
MAINTAINERS: Add target-devel list for drivers/target/
iscsi-target: Fix CONFIG_SMP=n and CONFIG_MODULES=n build failure
iscsi-target: Fix snprintf usage with MAX_PORTAL_LEN
iscsi-target: Fix uninitialized usage of cmd->pad_bytes
iscsi-target: strlen() doesn't count the terminator
iscsi-target: Fix NULL dereference on allocation failure
Problem: HW DDP context was not invalidated in case of ABORTS, etc...
This leads to the problem where memory pages which are used for DDP
as user descriptor could get reused for some other purpose (such as to
satisfy new memory allocation request either by kernel or user mode threads)
and since HW DDP context was not invalidated, HW continue to write to
those pages, hence causing memory corruption.
Fix: Either on incoming ABORTS or due to exchange time out, allowed the
target to cleanup HW DDP context if it was setup for respective ft_cmd.
Added new function to perform this cleanup, furthur it can be enhanced
for other cleanup activity. Fix ft_recv_write_data() to properly handle
fc_frame_payload_get to return pointer to payload if it exist. If there is
no payload which is most common case (+ve case in case if DDP is working
as expected, it will return NULL. Yes, scope of buf is limited to printk.
Invalidation of HW context (which is done inside ft_invl_hw_context() is
necessary in SUCCESS and FAILURE case of DDP. Hence invalidation is DONE
as long as there was DDP setup (whether it worked correctly or not,
NOTE: For some reason, if there is any error w.r.t DDP such as out of
order packet reception, HW simply post the full packet in rx queue.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Cc: Robert W Love <robert.w.love@intel.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in WRITE_SAME_16 LBA assignment where get_unaligned_be16()
is incorrectly being used instead of get_unaligned_be64() for a 64-bit LBA.
This was introduced with:
commit a1d8b49abd
Author: Andy Grover <agrover@redhat.com>
Date: Mon May 2 17:12:10 2011 -0700
target: Updates from AGrover and HCH (round 3)
(target: inline struct se_transport_task into struct se_cmd)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the following CONFIG_SMP=n and CONFIG_MODULES=n build
failure, because iscsit_thread_get_cpumask() is defined as a macro in
iscsi_target.c, but needed by iscsi_target_login.c
drivers/built-in.o: In function `iscsi_post_login_handler':
iscsi_target_login.c:(.text+0x13a315): undefined reference to `iscsit_thread_get_cpumask'
iscsi_target_login.c:(.text+0x13a4b4): undefined reference to `iscsit_thread_get_cpumask'
make: *** [.tmp_vmlinux1] Error 1
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes lio_target_call_addnptotpg() use sprintf() with
MAX_PORTAL_LEN + 1 to address the following smatch warning:
drivers/target/iscsi/iscsi_target_configfs.c +184 lio_target_call_addnptotpg(21)
error: snprintf() chops off the last chars of 'name': 257 vs 256
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes an uninitialized usage of cmd->pad_bytes inside of
iscsit_handle_text_cmd() introduced during a v4.1 change to use cmd
members instead of local pad_bytes variables.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes an off by one check in iscsit_add_tiqn() because the
NULL terminator isn't taken into consideration.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in iscsi_target_init_negotiation() where
the "goto out" path dereferences "login" which is NULL upon a
memory allocation failure.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Convert to DIV_ROUND_UP_SECTOR_T usage for sectors / dev_max_sectors
kernel.h: Add DIV_ROUND_UP_ULL and DIV_ROUND_UP_SECTOR_T macro usage
iscsi-target: Add iSCSI fabric support for target v4.1
iscsi: Add Serial Number Arithmetic LT and GT into iscsi_proto.h
iscsi: Use struct scsi_lun in iscsi structs instead of u8[8]
iscsi: Resolve iscsi_proto.h naming conflicts with drivers/target/iscsi
This patch adds the new macro usage of include/linux/kernel.h:DIV_ROUND_UP_SECTOR_T
for the new DIV_ROUND_UP_ULL() usage for 32-bit architectures with unsigned long long
sector_t division in transport_allocate_data_tasks() usage for target_core_mod v4.1
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
The Linux-iSCSI.org target module is a full featured in-kernel
software implementation of iSCSI target mode (RFC-3720) for the
current WIP mainline target v4.1 infrastructure code for the v3.1
kernel. More information can be found here:
http://linux-iscsi.org/wiki/ISCSI
This includes support for:
* RFC-3720 defined request / response state machines and support for
all defined iSCSI operation codes from Section 10.2.1.2 using libiscsi
include/scsi/iscsi_proto.h PDU definitions
* Target v4.1 compatible control plane using the generic layout in
target_core_fabric_configfs.c and fabric dependent attributes
within /sys/kernel/config/target/iscsi/ subdirectories.
* Target v4.1 compatible iSCSI statistics based on RFC-4544 (iSCSI MIBS)
* Support for IPv6 and IPv4 network portals in M:N mapping to TPGs
* iSCSI Error Recovery Hierarchy support
* Per iSCSI connection RX/TX thread pair scheduling affinity
* crc32c + crc32c_intel SSEv4 instruction offload support using libcrypto
* CHAP Authentication support using libcrypto
* Conversion to use internal SGl allocation with iscsit_alloc_buffs() ->
transport_generic_map_mem_to_cmd()
(nab: Fix iscsi_proto.h struct scsi_lun usage from linux-next in commit:
iscsi: Use struct scsi_lun in iscsi structs instead of u8[8])
(nab: Fix 32-bit compile warnings)
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andy Grover <agrover@redhat.com>
Acked-by: Roland Dreier <roland@kernel.org>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (77 commits)
[SCSI] fix crash in scsi_dispatch_cmd()
[SCSI] sr: check_events() ignore GET_EVENT when TUR says otherwise
[SCSI] bnx2i: Fixed kernel panic due to illegal usage of sc->request->cpu
[SCSI] bfa: Update the driver version to 3.0.2.1
[SCSI] bfa: Driver and BSG enhancements.
[SCSI] bfa: Added support to query PHY.
[SCSI] bfa: Added HBA diagnostics support.
[SCSI] bfa: Added support for flash configuration
[SCSI] bfa: Added support to obtain SFP info.
[SCSI] bfa: Added support for CEE info and stats query.
[SCSI] bfa: Extend BSG interface.
[SCSI] bfa: FCS bug fixes.
[SCSI] bfa: DMA memory allocation enhancement.
[SCSI] bfa: Brocade-1860 Fabric Adapter vHBA support.
[SCSI] bfa: Brocade-1860 Fabric Adapter PLL init fixes.
[SCSI] bfa: Added Fabric Assigned Address(FAA) support
[SCSI] bfa: IOC bug fixes.
[SCSI] bfa: Enable ASIC block configuration and query.
[SCSI] bnx2i: Updated copyright and bump version
[SCSI] bnx2i: Modified to skip CNIC registration if iSCSI is not supported
...
Fix up some trivial conflicts in:
- drivers/scsi/bnx2fc/{bnx2fc.h,bnx2fc_fcoe.c}:
Crazy broadcom version number conflicts
- drivers/target/tcm_fc/tfc_cmd.c
Just trivial cleanups done on adjacent lines
This patch drops transport_asciihex_to_binaryhex() in favor of proper
hex2bin usage from include/linux/kernel.h:hex2bin()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Additionally this patch brings proper apply of the designator type.
However, the original code luckily has no bug, because the association
equals to 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the default 'Unrestricted reordering allowed' for SCSI
control mode page QUEUE ALGORITHM MODIFIER on a per se_device basis in
target_modesense_control() following spc4r23. This includes a new
emuluate_rest_reord configfs attribute that currently (only) accepts
zero to signal 'Unrestricted reordering allowed' in control mode page
usage by the backend target device.
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch breaks up the ->map_task_SG() backend call into two seperate
->map_control_SG() and ->map_data_SG() in order to better address
IBLOCK and pSCSI. IBLOCK only allocates bios for ->map_data_SG(), and
pSCSI will allocate a struct request for both cases.
This patch fixes incorrect usage of ->map_task_SG() for all se_cmd descriptors
in transport_generic_new_cmd() by moving the call into it's proper location
directly inside of transport_allocate_data_tasks()
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch contains the squashed version of forth round series cleanups
from Andy and Christoph following the post heavy lifting in the preceeding:
'Eliminate usage of struct se_mem' and 'Make all control CDBs scatter-gather'
changes. This also includes a conversion of target core and the v3.0
mainline fabric modules (loopback and tcm_fc) to use pr_debug and the
CONFIG_DYNAMIC_DEBUG infrastructure!
These have been squashed into this third and final round for v3.1.
target: Remove ifdeffed code in t_g_process_write
target: Remove direct ramdisk code
target: Rename task_sg_num to task_sg_nents
target: Remove custom debug macros for pr_debug. Use pr_err().
target: Remove custom debug macros in mainline fabrics
target: Set WSNZ=1 in block limits VPD. Abort if WRITE_SAME sectors = 0
target: Remove transport do_se_mem_map callback
target: Further simplify transport_free_pages
target: Redo task allocation return value handling
target: Remove extra parentheses
target: change alloc_task call to take *cdb, not *cmd
(nab: Fix bogus struct file assignments in fd_do_readv and fd_do_writev)
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Both backstores and fabrics use arrays of struct scatterlist to describe
data buffers. However TCM used struct se_mems, basically a linked list
of scatterlist entries. We are able to simplify the code by eliminating
this intermediate data structure and just using struct scatterlist[]
throughout.
Also, moved attachment of task to cmd out of transport_generic_get_task
and into allocate_control_task and allocate_data_tasks. The reasoning
is that it's nonintuitive that get_task should automatically add it to
the cmd's task list -- it should just return an allocated, initialized
task. That's all it should do, based on the function's name, so either the
function shouldn't do it, or the name should change to encapsulate the
entire essence of what it does.
(nab: Fix compile warnings in tcm_fc, and make transport_kmap_first_data_page
honor sg->offset for SGLs from contigious memory with TCM_Loop, and
fix control se_cmd descriptor memory leak)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since sectors is not modified, it's more straightforward to do this.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Due to all cdbs' data buffers being referenced by scatterlists, buffers
of more than a page are not contiguous. Instead of handling this in all
control command handlers, we may be able to get away with just limiting
control cdb data buffers to one page. The only control CDBs we handle that
have potentially large data buffers are REPORT LUNS and UNMAP, so if we
didn't want to live with this limitation, they would need to be modified
to walk the pages in the data buffer's sgl.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Previously, some control CDBs did not allocate memory in pages for their
data buffer, but just did a kmalloc. This patch makes all cdbs allocate
pages.
This has the benefit of streamlining some paths that had to behave
differently when we used two allocation methods. The downside is that
all accesses to the data buffer need to kmap it before use, and need to
handle data in page-sized chunks if more than a page is needed for a given
command's data buffer.
Finally, note that cdbs with no data buffers are handled a little
differently. Before, SCSI_NON_DATA_CDBs would not call get_mem at all
(they'd be in the final else in transport_allocate_resources) but now
these will make it into generic_get_mem, but just not allocate any
buffers.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Implement page B1h, Block Device Characteristics, so that we can report
a medium rotation rate of 1 (non-rotating / solid state) if the
is_nonrot device attribute is set; we update the iblock backend to set
this attribute if the underlying Linux block device has its nonrot
flag set.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The current handling of VPD page 00h (Supported VPD Pages) for INQUIRY
commands has a couple of problems:
- The page length field is incorrectly set to 3, so the entry for 86h
(Extended INQUIRY Data) is ignored since it is in the fourth slot.
- Even though the code handles pages B0h and B2h, those pages aren't
mentioned in the Supported VPD Pages list, so eg the Linux SCSI stack
won't actually try to use them.
Fix these problems and make things more robust to avoid future problems
by moving to a table of supported VPD pages, which means that any added
VPD page support will automatically get reported on page 0.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In target_fabric_configfs_init(), we should allow fabric_mod to be NULL,
since THIS_MODULE is NULL for built-in modules. The main method of
using the target code may be as modules, but having everything built-in
is useful eg to be able to do quick testing with "qemu -kernel".
In any case, we shouldn't bomb out fabric registration for a perfectly
valid configuration, so simply drop the check of fabric_mod.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts ft_queue_cmd() to use wake_up_process() and
ft_thread() to use schedule_timeout_interruptible(MAX_SCHEDULE_TIMEOUT)
instead of wait_event_interruptible(). This fixes a potential race with
the wait_event_interruptible() conditional with qobj->queue_cnt in
ft_thread().
This patch also drops the unnecessary set_user_nice(current, -20) in
ft_thread(), and drops extra () around two if (!(acl)) conditionals in
tfc_conf.c.
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch removes the unnecessary EXTRA_CFLAGS includes, and drops the
unused -DTCM_FC_DEBUG define.
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
There is a memory leak in tcm_loop_make_scsi_hba().
If all the strstr() calls return NULL and we end up at return ERR_PTR(-EINVAL);
then we'll be leaking the memory previously allocated to tl_hba as
that variable goes out of scope.
This patch should fix the leak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger