Removing IFX0102 from tpm_tis was not a right move because both tpm_tis
and tpm_infineon use the same device ID. Revert the commit and add a
remark about a bug caused by commit 93e1b7d42e ("[PATCH] tpm: add HID
module parameter").
Fixes: e918e57041 ("tpm_tis: Remove the HID IFX0102")
Reported-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acer C720 running Linux v5.3 reports this in klog:
tpm_tis: 1.2 TPM (device-id 0xB, rev-id 16)
tpm tpm0: tpm_try_transmit: send(): error -5
tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts
tpm_tis tpm_tis: Could not get TPM timeouts and durations
tpm_tis 00:08: 1.2 TPM (device-id 0xB, rev-id 16)
tpm tpm0: tpm_try_transmit: send(): error -5
tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts
tpm_tis 00:08: Could not get TPM timeouts and durations
ima: No TPM chip found, activating TPM-bypass!
tpm_inf_pnp 00:08: Found TPM with ID IFX0102
% git --no-pager grep IFX0102 drivers/char/tpm
drivers/char/tpm/tpm_infineon.c: {"IFX0102", 0},
drivers/char/tpm/tpm_tis.c: {"IFX0102", 0}, /* Infineon */
Obviously IFX0102 was added to the HID table for the TCG TIS driver by
mistake.
Fixes: 93e1b7d42e ("[PATCH] tpm: add HID module parameter")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203877
Cc: stable@vger.kernel.org
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Reported-by: Ferry Toth: <ferry.toth@elsinga.info>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
On a Chromebook I'm working on I noticed a big (~1 second) delay
during bootup where nothing was happening. Right around this big
delay there were messages about the TPM:
[ 2.311352] tpm_tis_spi spi0.0: TPM ready IRQ confirmed on attempt 2
[ 3.332790] tpm_tis_spi spi0.0: Cr50 firmware version: ...
I put a few printouts in and saw that tpm_tis_spi_init() (specifically
tpm_chip_register() in that function) was taking the lion's share of
this time, though ~115 ms of the time was in cr50_print_fw_version().
Let's make a one-line change to prefer async probe for tpm_tis_spi.
There's no reason we need to block other drivers from probing while we
load.
NOTES:
* It's possible that other hardware runs through the init sequence
faster than Cr50 and this isn't such a big problem for them.
However, even if they are faster they are still doing _some_
transfers over a SPI bus so this should benefit everyone even if to
a lesser extent.
* It's possible that there are extra delays in the code that could be
optimized out. I didn't dig since once I enabled async probe they
no longer impacted me.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The tpm2_get_cc_attrs_tbl() call will result in TPM commands being issued,
which will need the use of the internal command/response buffer. But,
we're issuing this *before* we've waited to make sure that buffer is
allocated.
This can result in intermittent failures to probe if the hypervisor / TPM
implementation doesn't respond quickly enough. I find it fails almost
every time with an 8 vcpu guest under KVM with software emulated TPM.
To fix it, just move the tpm2_get_cc_attrs_tlb() call after the
existing code to wait for initialization, which will ensure the buffer
is allocated.
Fixes: 18b3670d79 ("tpm: ibmvtpm: Add support for TPM2")
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Trivial fix, the spelling of "drescription" is incorrect
in function comment.
Fix this.
Signed-off-by: Binbin Zhou <zhoubinbin@uniontech.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Found by smatch:
drivers/char/tpm/tpm_tis_core.c:1088 tpm_tis_core_init() warn:
variable dereferenced before check 'chip->ops' (see line 979)
'chip->ops' is assigned in the beginning of function
in tpmm_chip_alloc->tpm_chip_alloc
and is used before first possible goto to error path.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
During flow control we are just reading from the TPM, yet our spi_xfer
has the tx_buf and rx_buf both non-NULL which means we're requesting a
full duplex transfer.
SPI is always somewhat of a full duplex protocol anyway and in theory
the other side shouldn't really be looking at what we're sending it
during flow control, but it's still a bit ugly to be sending some
"random" data when we shouldn't.
The default tpm_tis_spi_flow_control() tries to address this by
setting 'phy->iobuf[0] = 0'. This partially avoids the problem of
sending "random" data, but since our tx_buf and rx_buf both point to
the same place I believe there is the potential of us sending the
TPM's previous byte back to it if we hit the retry loop.
Another flow control implementation, cr50_spi_flow_control(), doesn't
address this at all.
Let's clean this up and just make the tx_buf NULL before we call
flow_control(). Not only does this ensure that we're not sending any
"random" bytes but it also possibly could make the SPI controller
behave in a slightly more optimal way.
NOTE: no actual observed problems are fixed by this patch--it's was
just made based on code inspection.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
It has been reported that some TIS based TPMs are giving unexpected
errors when using the O_NONBLOCK path of the TPM device. The problem
is that some TPMs don't like it when you get and then relinquish a
locality (as the tpm_try_get_ops()/tpm_put_ops() pair does) without
sending a command. This currently happens all the time in the
O_NONBLOCK write path. Fix this by moving the tpm_try_get_ops()
further down the code to after the O_NONBLOCK determination is made.
This is safe because the priv->buffer_mutex still protects the priv
state being modified.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206275
Fixes: d23d124843 ("tpm: fix invalid locking in NONBLOCKING mode")
Reported-by: Mario Limonciello <Mario.Limonciello@dell.com>
Tested-by: Alex Guzman <alex@guzman.io>
Cc: stable@vger.kernel.org
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
Also, the following issue shows up due to the flexible-array member
having incomplete type[4]:
drivers/char/tpm/eventlog/tpm2.c: In function ‘tpm2_bios_measurements_start’:
drivers/char/tpm/eventlog/tpm2.c:54:46: error: invalid application of ‘sizeof’ to incomplete type ‘u8[]’ {aka ‘unsigned char[]’}
54 | size = sizeof(struct tcg_pcr_event) - sizeof(event_header->event)
| ^
drivers/char/tpm/eventlog/tpm2.c: In function ‘tpm2_bios_measurements_next’:
drivers/char/tpm/eventlog/tpm2.c:102:10: error: invalid application of ‘sizeof’ to incomplete type ‘u8[]’ {aka ‘unsigned char[]’}
102 | sizeof(event_header->event) + event_header->event_size;
| ^
drivers/char/tpm/eventlog/tpm2.c: In function ‘tpm2_binary_bios_measurements_show’:
drivers/char/tpm/eventlog/tpm2.c:140:10: error: invalid application of ‘sizeof’ to incomplete type ‘u8[]’ {aka ‘unsigned char[]’}
140 | sizeof(event_header->event) + event_header->event_size;
| ^
scripts/Makefile.build:266: recipe for target 'drivers/char/tpm/eventlog/tpm2.o' failed
make[3]: *** [drivers/char/tpm/eventlog/tpm2.o] Error 1
As mentioned above: "Flexible array members have incomplete type, and
so the sizeof operator may not be applied. As a quirk of the original
implementation of zero-length arrays, sizeof evaluates to zero."[1] As
in "sizeof(event_header->event) always evaluated to 0, so removing it
has no effect".
Lastly, make use of the struct_size() helper to deal with the
flexible array member and its host structure.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
[4] https://github.com/KSPP/linux/issues/43
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
There is export_uuid() function which exports uuid_t to the u8 array.
Use it instead of open coding variant.
This allows to hide the uuid_t internals.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Call disable_interrupts() if we have to revert to polling in order not to
unnecessarily reserve the IRQ for the life-cycle of the driver.
Cc: stable@vger.kernel.org # 4.5.x
Reported-by: Hans de Goede <hdegoede@redhat.com>
Fixes: e3837e74a0 ("tpm_tis: Refactor the interrupt setup")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
For the algorithm that does not match the bank, a positive
value EINVAL is returned here. I think this is a typo error.
It is necessary to return an error value.
Cc: stable@vger.kernel.org # 5.4.x
Fixes: 9f75c82246 ("KEYS: trusted: correctly initialize digests and fix locking issue")
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
tpm_ibmvtpm_send() can fail during PowerVM Live Partition Mobility resume
with an H_CLOSED return from ibmvtpm_send_crq(). The PAPR says, 'The
"partner partition suspended" transport event disables the associated CRQ
such that any H_SEND_CRQ hcall() to the associated CRQ returns H_Closed
until the CRQ has been explicitly enabled using the H_ENABLE_CRQ hcall.'
This patch adds a check in tpm_ibmvtpm_send() for an H_CLOSED return from
ibmvtpm_send_crq() and in that case calls tpm_ibmvtpm_resume() and
retries the ibmvtpm_send_crq() once.
Cc: stable@vger.kernel.org # 3.7.x
Fixes: 132f762947 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Reported-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: George Wilson <gcwilson@linux.ibm.com>
Tested-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This patch fixes the following problem when the ibmvtpm driver
is built as a module:
ERROR: modpost: "tpm2_get_cc_attrs_tbl" [drivers/char/tpm/tpm_ibmvtpm.ko] undefined!
make[1]: *** [scripts/Makefile.modpost:94: __modpost] Error 1
make: *** [Makefile:1298: modules] Error 2
Fixes: 18b3670d79 ("tpm: ibmvtpm: Add support for TPM2")
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Commit 9255782f70 ("sysfs: Wrap __compat_only_sysfs_link_entry_to_kobj
function to change the symlink name") made this function a wrapper
around a new non-underscored function, which is a bit odd. The normal
naming convention is the other way around: the underscored function is
the wrappee, and the non-underscored function is the wrapper.
There's only one single user (well, two call-sites in that user) of the
more limited double underscore version of this function, so just remove
the oddly named wrapper entirely and just add the extra NULL argument to
the user.
I considered just doing that in the merge, but that tends to make
history really hard to read.
Link: https://lore.kernel.org/lkml/CAHk-=wgkkmNV5tMzQDmPAQuNJBuMcry--Jb+h8H1o4RA3kF7QQ@mail.gmail.com/
Cc: Sourabh Jain <sourabhjain@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support TPM2 in the IBM vTPM driver. The hypervisor tells us what
version of TPM is connected through the vio_device_id.
In case a TPM2 device is found, we set the TPM_CHIP_FLAG_TPM2 flag
and get the command codes attributes table. The driver does
not need the timeouts and durations, though.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Synchronize with the results from the CRQs before continuing with
the initialization. This avoids trying to send TPM commands while
the rtce buffer has not been allocated, yet.
This patch fixes an existing race condition that may occurr if the
hypervisor does not quickly respond to the VTPM_GET_RTCE_BUFFER_SIZE
request sent during initialization and therefore the ibmvtpm->rtce_buf
has not been allocated at the time the first TPM command is sent.
Fixes: 132f762947 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
A vTPM 2.0 is identified by 'IBM,vtpm20' in the 'compatible' node in
the device tree. Handle it in the same way as 'IBM,vtpm'.
The vTPM 2.0's log is written in little endian format so that for this
aspect we can rely on existing code.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
In a recent change to the SPI subsystem [1], a new 'delay' struct was added
to replace the 'delay_usecs'. This change replaces the current
'delay_usecs' with 'delay' for this driver.
The 'spi_transfer_delay_exec()' function [in the SPI framework] makes sure
that both 'delay_usecs' & 'delay' are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
For /sys/kernel/security/tpm0/binary_bios_measurements:
1) read after lseek beyound end of file generates whole last line.
2) read after lseek to middle of last line generates
expected end of last line and unexpected whole last line once again.
Cc: stable@vger.kernel.org # 4.19.x
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
In case of /sys/kernel/security/tpm0/ascii_bios_measurements
and binary_bios_measurements:
1) read after lseek beyound end of file generates whole last line.
2) read after lseek to middle of last line generates
expected end of last line and unexpected whole last line once again.
Cc: stable@vger.kernel.org # 4.19.x
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
If a TPM is in disabled state, it's reasonable for it to have an empty
log. Bailing out of probe in this case means that the PPI interface
isn't available, so there's no way to then enable the TPM from the OS.
In general it seems reasonable to ignore log errors - they shouldn't
interfere with any other TPM functionality.
Signed-off-by: Matthew Garrett <matthewgarrett@google.com>
Cc: stable@vger.kernel.org # 4.19.x
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
chip->allocated_banks, an array of tpm_bank_info structures, contains the
list of TPM algorithm IDs of allocated PCR banks. It also contains the
corresponding ID of the crypto subsystem, so that users of the TPM driver
can calculate a digest for a PCR extend operation.
However, if there is no mapping between TPM algorithm ID and crypto ID, the
crypto_id field of tpm_bank_info remains set to zero (the array is
allocated and initialized with kcalloc() in tpm2_get_pcr_allocation()).
Zero should not be used as value for unknown mappings, as it is a valid
crypto ID (HASH_ALGO_MD4).
Thus, initialize crypto_id to HASH_ALGO__LAST.
Cc: stable@vger.kernel.org # 5.1.x
Fixes: 879b589210 ("tpm: retrieve digest size of unknown algorithms with PCR read")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Revert tpm_tis_spi_mod.ko back to tpm_tis_spi.ko as the rename could
break user space scripts. This can be achieved by renaming tpm_tis_spi.c
as tpm_tis_spi_main.c. Then tpm_tis_spi-y can be used inside the
makefile.
Cc: Andrey Pronin <apronin@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: stable@vger.kernel.org # 5.5.x
Fixes: 797c0113c9 ("tpm: tpm_tis_spi: Support cr50 devices")
Reported-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Easily determining what TCG version a tpm device implements
has been a pain point for userspace for a long time, so
add a sysfs file to report the TCG major version of a tpm device.
Also add an entry to Documentation/ABI/stable/sysfs-class-tpm
describing the new file.
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Mimi Zohar <zohar@linux.ibm.com>
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-integrity@vger.kernel.org
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The priv->response_length can hold the size of an response or an negative
error code, and the tpm_common_read() needs to handle both cases correctly.
Changed the type of response_length to signed and accounted for negative
value in tpm_common_read().
Cc: stable@vger.kernel.org
Fixes: d23d124843 ("tpm: fix invalid locking in NONBLOCKING mode")
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
There has been a bunch of reports (one from kernel bugzilla linked)
reporting that when this commit is applied it causes on some machines
boot freezes.
Unfortunately hardware where this commit causes a failure is not widely
available (only one I'm aware is Lenovo T490), which means we cannot
predict yet how long it will take to properly fix tpm_tis interrupt
probing.
Thus, the least worst short term action is to revert the code to the
state before this commit. In long term we need fix the tpm_tis probing
code to work on machines that Stefan's fix was supposed to fix.
Fixes: 21df4a8b60 ("tpm_tis: reserve chip for duration of tpm_tis_core_init")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205935
Cc: stable@vger.kernel.org
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Xiaoping Zhou <xiaoping.zhou@intel.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
There has been a bunch of reports (one from kernel bugzilla linked)
reporting that when this commit is applied it causes on some machines
boot freezes.
Unfortunately hardware where this commit causes a failure is not widely
available (only one I'm aware is Lenovo T490), which means we cannot
predict yet how long it will take to properly fix tpm_tis interrupt
probing.
Thus, the least worst short term action is to revert the code to the
state before this commit. In long term we need fix the tpm_tis probing
code to work on machines that Stefan's fix was supposed to fix.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205935
Fixes: 1ea32c83c6 ("tpm_tis_core: Set TPM_CHIP_FLAG_IRQ before probing for interrupts")
Cc: stable@vger.kernel.org
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Xiaoping Zhou <xiaoping.zhou@intel.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Revert a commit, which was included in Linux v5.5-rc3 because it did not
properly fix the issues it was supposed to fix.
Fixes: 21df4a8b60 ("tpm_tis: reserve chip for duration of tpm_tis_core_init")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205935
Cc: stable@vger.kernel.org
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Xiaoping Zhou <xiaoping.zhou@intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Add shutdown call back to close existing session with fTPM TA
to support kexec scenario.
Add parentheses to function names in comments as specified in kdoc.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@microsoft.com>
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
When an application sends TPM commands in NONBLOCKING mode
the driver holds chip->tpm_mutex returning from write(),
which triggers: "WARNING: lock held when returning to user space".
To fix this issue the driver needs to release the mutex before
returning and acquire it again in tpm_dev_async_work() before
sending the command.
Cc: stable@vger.kernel.org
Fixes: 9e1b74a63f (tpm: add support for nonblocking operation)
Reported-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in>
Tested-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The original code, before it was moved into security/keys/trusted-keys
had a flush after the blob unseal. Without that flush, the volatile
handles increase in the TPM until it becomes unusable and the system
either has to be rebooted or the TPM volatile area manually flushed.
Fix by adding back the lost flush, which we now have to export because
of the relocation of the trusted key code may cause the consumer to be
modular.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixes: 2e19e10131 ("KEYS: trusted: Move TPM2 trusted keys code")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Instead of repeatedly calling tpm_chip_start/tpm_chip_stop when
issuing commands to the tpm during initialization, just reserve the
chip after wait_startup, and release it when we are ready to call
tpm_chip_register.
Cc: Christian Bundy <christianbundy@fraction.io>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Cc: linux-integrity@vger.kernel.org
Fixes: a3fbfae82b ("tpm: take TPM chip power gating out of tpm_transmit()")
Fixes: 5b359c7c43 ("tpm_tis_core: Turn on the TPM before probing IRQ's")
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need support
for time64_t.
In completely unrelated work, I spent time on cleaning up parts of this
file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the rest
of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which is
the scsi ioctl handlers. I have patches for those as well, but they need
more testing or possibly a rewrite.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgCl
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
platform_get_irq() calls dev_err() on an error. As the IRQ usage in the
tpm_tis driver is optional, this is undesirable.
Specifically this leads to this new false-positive error being logged:
[ 5.135413] tpm_tis MSFT0101:00: IRQ index 0 not found
This commit switches to platform_get_irq_optional(), which does not log
an error, fixing this.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()"
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Bug link: https://bugzilla.kernel.org/show_bug.cgi?id=195657
cmd/rsp buffers are expected to be in the same ACPI region.
For Zen+ CPUs BIOS's might report two different regions, some of
them also report region sizes inconsistent with values from TPM
registers.
Memory configuration on ASRock x470 ITX:
db0a0000-dc59efff : Reserved
dc57e000-dc57efff : MSFT0101:00
dc582000-dc582fff : MSFT0101:00
Work around the issue by storing ACPI regions declared for the
device in a fixed array and adding an array for pointers to
corresponding possibly allocated resources in crb_map_io function.
This data was previously held for a single resource
in struct crb_priv (iobase field) and local variable io_res in
crb_map_io function. ACPI resources array is used to find index of
corresponding region for each buffer and make the buffer size
consistent with region's length. Array of pointers to allocated
resources is used to map the region at most once.
Signed-off-by: Ivan Lazeev <ivan.lazeev@gmail.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Move TPM2 trusted keys code to trusted keys subsystem. The reason
being it's better to consolidate all the trusted keys code to a single
location so that it can be maintained sanely.
Also, utilize existing tpm_send() exported API which wraps the internal
tpm_transmit_cmd() API.
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Move tpm_buf code to common include/linux/tpm.h header so that it can
be reused via other subsystems like trusted keys etc.
Also rename trusted keys and asymmetric keys usage of TPM 1.x buffer
implementation to tpm1_buf to avoid any compilation errors.
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The current code uses GFP_HIGHMEM, which is wrong because GFP_HIGHMEM
(on 32 bit systems) is memory ordinarily inaccessible to the kernel
and should only be used for allocations affecting userspace. In order
to make highmem visible to the kernel on 32 bit it has to be kmapped,
which consumes valuable entries in the kmap region. Since the tpm_buf
is only ever used in the kernel, switch to using a GFP_KERNEL
allocation so as not to waste kmap space on 32 bits.
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
devm_kcalloc() can fail and return NULL so we need to check for that.
Cc: stable@vger.kernel.org
Fixes: 58472f5cd4 ("tpm: validate TPM 2.0 commands")
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Some of these includes aren't used, for example of_gpio.h and freezer.h,
or they are missing, for example kernel.h for min_t() usage. Add missing
headers and remove unused ones so that we don't have to expand all these
headers into this file when they're not actually necessary.
Cc: Andrey Pronin <apronin@chromium.org>
Cc: Duncan Laurie <dlaurie@chromium.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Alexander Steffen <Alexander.Steffen@infineon.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Add TPM2.0 PTP FIFO compatible SPI interface for chips with Cr50
firmware. The firmware running on the currently supported H1 Secure
Microcontroller requires a special driver to handle its specifics:
- need to ensure a certain delay between SPI transactions, or else
the chip may miss some part of the next transaction
- if there is no SPI activity for some time, it may go to sleep,
and needs to be waken up before sending further commands
- access to vendor-specific registers
Cr50 firmware has a requirement to wait for the TPM to wakeup before
sending commands over the SPI bus. Otherwise, the firmware could be in
deep sleep and not respond. The method to wait for the device to wakeup
is slightly different than the usual flow control mechanism described in
the TCG SPI spec. Add a completion to tpm_tis_spi_transfer() before we
start a SPI transfer so we can keep track of the last time the TPM
driver accessed the SPI bus to support the flow control mechanism.
Split the cr50 logic off into a different file to keep it out of the
normal code flow of the existing SPI driver while making it all part of
the same module when the code is optionally compiled into the same
module. Export a new function, tpm_tis_spi_init(), and the associated
read/write/transfer APIs so that we can do this. Make the cr50 code wrap
the tpm_tis_spi_phy struct with its own struct to override the behavior
of tpm_tis_spi_transfer() by supplying a custom flow control hook. This
shares the most code between the core driver and the cr50 support
without combining everything into the core driver or exporting module
symbols.
Signed-off-by: Andrey Pronin <apronin@chromium.org>
Cc: Andrey Pronin <apronin@chromium.org>
Cc: Duncan Laurie <dlaurie@chromium.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Alexander Steffen <Alexander.Steffen@infineon.com>
Cc: Heiko Stuebner <heiko@sntech.de>
[swboyd@chromium.org: Replace boilerplate with SPDX tag, drop
suspended bit and remove ifdef checks in cr50.h, migrate to functions
exported in tpm_tis_spi.h, combine into one module instead of two]
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cr50 firmware has a different flow control protocol than the one used by
this TPM PTP SPI driver. Introduce a flow control callback so we can
override the standard sequence with the custom one that Cr50 uses.
Cc: Andrey Pronin <apronin@chromium.org>
Cc: Duncan Laurie <dlaurie@chromium.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Alexander Steffen <Alexander.Steffen@infineon.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
On some platforms, the TPM power is managed by firmware and therefore we
don't need to stop the TPM on suspend when going to a light version of
suspend such as S0ix ("freeze" suspend state). Add a chip flag,
TPM_CHIP_FLAG_FIRMWARE_POWER_MANAGED, to indicate this so that certain
platforms can probe for the usage of this light suspend and avoid
touching the TPM state across suspend/resume.
Cc: Andrey Pronin <apronin@chromium.org>
Cc: Duncan Laurie <dlaurie@chromium.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Alexander Steffen <Alexander.Steffen@infineon.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
There was revealed a bug in the STM TPM chipset used in Dell R415s.
Bug is observed so far only on chipset firmware 1.2.8.28
(1.2 TPM, device-id 0x0, rev-id 78). After some number of
operations chipset hangs and stays in inconsistent state:
tpm_tis 00:09: Operation Timed out
tpm_tis 00:09: tpm_transmit: tpm_send: error -5
Durations returned by the chip are the same like on other
firmware revisions but apparently with specifically 1.2.8.28 fw
durations should be reset to 2 minutes to enable tpm chip work
properly. No working way of updating firmware was found.
This patch adds implementation of ->update_durations method
that matches only STM devices with specific firmware version.
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Alexey Klimov <aklimov@redhat.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (!update_durations path)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (!update_durations path)
Patch adds method ->update_durations to override returned
durations in case TPM chip misbehaves for TPM 1.2 drivers.
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Alexey Klimov <aklimov@redhat.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (!update_durations path)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Replace existing TPM 1.x version structs with new structs that consolidate
the common parts into a single struct so that code duplication is no longer
needed in caps_show().
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Alexey Klimov <aklimov@redhat.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Jarkko Sakkinen